Search Results

Search found 6931 results on 278 pages for 'almost surely'.

Page 248/278 | < Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >

• md/raid:md2: cannot start dirty degraded array, kernel panic

  - by nl-x

  After having made use of a remote power switch, my server did not come back online. When I went to the datacenter and reboot the computer on the spot I see the server booting (I see the centos progress bar with running almost all the way to the end) and eventually giving the following messages: md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init not tainted 2.6.32-279.1.1.el6.i686 #1 Call Trace: [<c083bfbc>] ? panic+0x68/0x11c [<c045a501>] ? do_exit+0x741/0x750 [<c045a54c>] ? do_group_exit+0x3c/0xa0 [<c045a5c1>] ? sys_exit_group+0x11/0x20 [<c083eba4>] ? syscall_call+0x7/0xb [<c083007b>] ? cmos_wake_setup+0x62/0x112 The server runs CentOS and has software raid, and I don't have backups of the raid settings. The only backup I have is of /home and the database dumps. (Glad to at least have those though.) Since the server is an old Dell PowerEdge 1750 with no CD-ROM drive, I have no way of booting the machine from a boot disk. I also remember in the past that the server also wouldn't boot from a bootable USB disk. So the only way I know how to boot the server is to go to the datacenter, pick up the server and take it to the office. Screw open the server. Attach a cdrom drive to an IDE slot on the motherboard. And then boot it. I am hoping you guys could help me avoid this. I have looked a bit through the boot options and I found the following boot options. When CentOS is about to boot and interrupt the boot-countdown: CentOS (2.6.32-279.1.1.el63.i686) CentOS Linux (2.6.32-71.29.1.el6.i686) centos (2.6.32-71.el6.i686) I think the first configuration is the default one, because choosing that gets me to the above mentioned kernel panic. The other ones end with something like "Sleeping forever". I can press 'e' to edit boot commands, press 'a' to modify kernel arguments and press 'c' for grub command line. The command line gives a grub prompt. But I have no idea how to get the system to boot without (trying to) access the dirty partitions. What I want to do is off course: - boot the machine - check hard drive for errors - mark the drive as clean

  Read the article

• Postfix logs missing information on delivery status (postfix/smtp message)

  - by hegemon

  I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

  Read the article

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• What is the best server or Ip address to use for prolonged testing?

  - by eldorel

  I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

  Read the article

• What would cause Memcached to Hang for 2+ seconds?

  - by Brad Dwyer

  I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• .AVI Files randomly cease to open, other strange errors too

  - by Ben Franchuk

  I Recently (a couple weeks ago) downloaded the complete series of Seinfeld, all in varying file type. I Watched them in sequence according to season and to airing date, and all was well. All of the files played fine with my media player of choice ("BS Player"), and once I had finished, I went onto watch some other TV I had previously downloaded (The U.S. Series of "The Office"), and after then, some other film and then some music, over the following weeks (keep in mind all of these files are all on the same Hard Drive). Later then, More recently, I Went back to watching Seinfeld. The episodes played well as they did before- with the exclusion of a few in Season 7. I Have not tested all of the episodes in the season, but upon inspection, the majority of them are experiencing this problem; the problem being simply that they don't open! BS Player says that the files are either damaged or that the codecs to play the files are not on my computer-- however I am certain that the files DO have the codecs, and I am pretty sure that they are NOT DAMAGED either. I Have played the files with other players (such as VLC, Media Player Classic, and Windows Media Player), too, only to the same result; of them not opening. Seemingly the only way that I can differentiate between a damaged file and a non-damaged file are the way that the icon shows in Windows Explorer. For example, the below image is how explorer shows the information of a file that is non-damaged... ...and below is how a damaged file appears... The most disturbing and confusing part of this, though, is the last episode in the season- It opens, but not as a video- Instead, as a 1 Hour, 16 Minute, and 35 Second Audio file! The file plays a song for the first 4 or so minutes, and then is pretty much silent (except for some extremely quiet noise) until the last minute or so, when a random array of chopped up sounds and beeping noises play. I Do not recognise the song at the beginning of the file, but by the sounds of it, it is a song by the artist "Mr. Oizo," who's complete works I downloaded a couple weeks before now; and a bit before then I had finished downloading season 9 (not affected by these problems) of Seinfeld. I'd also like to note that the file I told of earlier (which played audio instead of video) reads as the same size as the other files in the season (around 175 MB) and also opens as a video clip. I Have NEVER experienced any of these problems in the past, and they seem to be only effecting the one season of my downloaded TV. The problems have not arisen with any of the other files on my Hard Drive, or any of the files downloaded around the time or after the time of which I downloaded season 7 of Seinfeld- or at least to my noticing. I Use the hard drive these files are located on almost every day, so could that be the cause of these problems? Is this a sign that my HDD is soon going to die? If it helps, the HDD is a Western Digital MyBook 1.5 TB 7500 RPM. It is connected to the computer via U.S.B. 2.0. EDIT! I noticed that this problem is now occurring with Season 9 of Seinfeld- and, presumably, other files on the drive I have yet to check. Please, If you have ANY IDEA AT ALL on what may be causing this or how to fix it, do tell me!

  Read the article

• Do hard drive enclosures fail/is it the HDD or enclosure?

  - by x0a

  I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

  Read the article

• VMware vSphere cluster design for site redundancy

  - by Stefan Radovanovici

  I have a question about the best design for site redudancy when using vSphere clusters. A bit of background info about our situation first though. We are a medium-sized company with two main offices, located in different countries. Our networks are linked by a Layer2 150Mbps leased line which is currently underused. We have a variety of services running for internal use within the company, some on physycal servers and some on existing vSphere clusters. In our department we also run several services (almost all running under various forms of Linux) like NTP, Syslog, jump servers, monitoring servers and so on. We have now the requirement that those servers need to be redundant within each location (which they are not at the moment) and also site redudant (which they are to some extent, the servers are duplicated in the 2nd location with configurations kept in sync via various methods at the application layer). There is no SAN available for us, at least not something that we can use at the moment. Cost is also an issue. While we do have some budget available for this, we can't afford to buy SANs for both locations for example. I looked at the VSA feature and it seems that this could be something for us but I am unsure how to solve the site-redudancy requirement. At the moment for testing purposes I am setting up in a lab a vSphere 5 with VSA on two ESXi hosts. I am currently using the Essentials Plus kit with VSA license, which allows me to build a VSA cluster on up to 3 hosts, together with a vCenter license to manage them. The hosts each have two dual-port network cards and two 600GB drives, running in Raid1. Hardware-wise this will be enough for us to run the all the services we need as VMs and will provide redundandcy within the site. At the moment I see only two option to have site redundancy: build an identical VSA cluter in the second location and keep the various services sync'ed at application layer (database sync, rsync and so on). simply move one of the hosts from the existing cluster to the second location, basically having the VSA cluster span the 150Mbps link between the sites. I would very much prefer the second option but I am unsure how well it'll work, if it can work at all. Technically it should, we can span the needed VLANs across the leased line and have them available in the second location. The advantage would be that we don't need to worry at all about sync'ing databases and the like. But I have the feeling that the bandwidth will not be enough, I have no way of knowing how much traffic will the VSA cluster generate between the hosts. I realize that this will most likely depend on the individual usage of the VMs but still, I have no idea how VSA replicates data between the ESXi hosts. Are these my only options or can my goals be achieved in some other way ? Is there perhaps a way to have some sort of "cold stand by" cluster in the second location where the VMs would be sync'ed once per night from the main location ? The idea is that in case the first site becomes unavailable, we would be able to bring all those VMs online there. We would be ok with the data being 1 day old. Any answers are appreciated. Best regards, Stefan

  Read the article

• Linux: Apple Wireless A1314 Fn key not registered, looks like software bug

  - by ramplank

  I'm trying to set up my Apple Wireless Keyboard with my Kubuntu systems. These are PC hardware powered by Intel Atom and Intel i5 respectively. The keyboard has a US keyboard layout and has model number A1314 written on the back. It takes two AA batteries. I'm saying that because it appears there are multiple types of model A1314. I have tried this on a 10.04, 11.04, 11.10 and 12.04 system with no success. Every time using a bluetooth dongle and the KDE bluetooth notification tray applet, the keyboard can be connected. In both cases it shows up as "Apple Wireless Keyboard". Almost everything works as expected, in fact, I'm typing on it right now. But one thing doesn't: The Fn key. I'd like to use Fn + Down Arrow as PgDn / Page Down, I understand this is default behaviour on Apple keyboards. And of course I'd like the same for Page Up, Home and End. I'll stick to Page Down in my example. I used the xev tool to see the keycodes the system receives, and if I press on Fn nothing happens, and nothing is registered. If I press Fn + Down Arrow, xev only registers the down arrow. Here's the output from my 11.04 system to illustrate: Press just the Fn key: no output Press Down Arrow key: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699773, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699860, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False Press Fn+Down Arrow Keys together: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701548, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701623, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False I've been searching this forum and other Linux-related forums for hours but I still have not found a solution. I mostly found advice on how to fix this when using an actual apple laptop or desktop, but I don't have that. They said to try something like the following echo 2 > /sys/module/hid_apple/ ... But since there's no hid_apple directory present on my systems, I've needed to modprobe hid_apple first. That didn't help either. I'm cool with changing some config files, or compiling my own patched kernel if that's necessary. I currently have a 10.04 and 12.04 system available to test. The same issue occurs when hooked up to Windows 7. Fn key still does nothing, not by itself or in combination with other keys. With some AutoHotkey fiddling, I was able to confirm the key is registered as pressed, but ignored by default. A custom AutoHotkey script can fix that. But AutoHotkey is only for Windows, I want my problem fixed on Linux. Hooked up to an iPad 2 it only works in combination with the F1-F12 keys. Not with the arrow keys. If the screen of the ipad is off, and I press just the Fn key, the screen will come on, so the key itself is registered as pressed. So to sum up my question: Can anyone help me get Page Up, Page Down, Home and End to work on this keyboard, when that requires me to use an Fn key which is currently not registered?

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• Unable to make the session state request to the session state server.

  - by Angry_IT_Guru

  For about 4-5 months now, I seem to be having this sporadic issue--mainly during our busiest time of the day between 10:30-11:45AM, where all my Windows 2003 web servers in a Microsoft NLB cluster start throwing session state server errors. A sample error is below. System.Web.HttpException: Unable to make the session state request to the session state server. Please ensure that the ASP.NET State service is started and that the client and server ports are the same. If the server is on a remote machine, please ensure that it accepts remote requests by checking the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\aspnet_state\Parameters\AllowRemoteConnection. If the server is on the local machine, and if the before mentioned registry value does not exist or is set to 0, then the state server connection string must use either 'localhost' or '127.0.0.1' as the server name. at System.Web.SessionState.OutOfProcSessionStateStore.MakeRequest(StateProtocolVerb verb, String id, StateProtocolExclusive exclusiveAccess, Int32 extraFlags, Int32 timeout, Int32 lockCookie, Byte[] buf, Int32 cb, Int32 networkTimeout, SessionNDMakeRequestResults& results) at System.Web.SessionState.OutOfProcSessionStateStore.SetAndReleaseItemExclusive(HttpContext context, String id, SessionStateStoreData item, Object lockId, Boolean newItem) at System.Web.SessionState.SessionStateModule.OnReleaseState(Object source, EventArgs eventArgs) at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Now I'm using ASP.NET State service on a centralized back-end Windows 2003 server that all servers communicate to. I was originally using SQL Server state for a couple years as well prior to having this issue. The problem with SQL wqas that when the issue occurred, it created a blocking situation which essentially impacted all users across all servers. The product company recommended that I use the standard ASP.NET State service as that was what they technically supported. Why this would make a difference is beyond me -- but I had no choice but to try it! I have attempted to create multiple application pools, adding additional servers, chaning TCP/IP timeout from 20 to 30 seconds, and even calling Microsoft ASP.NET product support, with very little success. I even recommended that they review whether they are using read-only session state instead of read/write per page request -- as I understand that this basically causes every page to make round-trips to state server even if state isn't being used on the page. Unfortunately, the application is developed by our product company and they insist that it is something with my environment because other clients do not have these sort of issues. However, I've talked to other clients and they tell me when they've seen issues like they, they've basically had to create another web farm. This issue almost seems like I've simply reached some architectural limit within the application... Microsoft's position on the issue is that the session state needs to be reduced and the returncode being reported back from the state server indicates buffers are full. To better understand the scope of issues (rather than wait for customers to call and complain), I installed ELMAH and configured it to send me e-mails when unhandled exceptions occur. I basically get 500-1000 e-mails during the time period of high activity! If any one has any other ideas I could try or better ways to troubleshoot, I'd appreciate it.

  Read the article

• I am starting to think that Prevx.com isnt a legit site...but heres my long-winded question

  - by cop1152

  I apologize in advance for the long-winded post. I posted it all because I believe its informative and may be useful. Also, I posted my question at the end. Moments ago I was RDC to a file server in my home (from inside my home). I had opened Firefox and Googled for a manufacturers website. Immediately after clicking the link, Firefox abruptly closed. This seemed odd to me to so I checked the running processes and discovered d.exe, e.exe, and f.exe running. I Googled these processes on a different machine and found them belonging to a key-logger/screen-capturer/trojan called defender.exe, which according to the Prevx lives in c:\documents and settings\user\local settings\temp. (Prevx link http://www.prevx.com/filenames/147352809685142526-X1/DEFENDER32.EXE.html) Simultaneously, an obviously-spoofed Windows Firewall popup appeared on the server asking me to click ‘yes’ to update Windows Firewall. At this time I ended all rogue processes, emptied the temp folder, removed defender.exe from startup, and checked my registry and a few other locations. Before deleting Defender.exe I noted that it was created moments ago, just before Firefox crashed. I believe that I was ‘almost’ infected with this malware. I believe that it needed me to click the phony popup in order to complete infection because it wasn’t allowed to execute processes from the temp folder. After cleaning the machine, I restarted it and have been monitoring it for over an hour. I am debating on whether or not to restore the Windows partition (a separate physical drive from the data) or to just watch it for awhle. I should mention that, because of the specs on this machine, I do not run antivirus software, but I know it well and inspect it regularly. It is a very old Compaq with a 400mhz processer and 512mb of ram. I have a static IP and the server is in the DMZ running an FTP client and some HTTP server software. All files transferred to and stored on this machine are scanned for malware before transferring. Usually the machine only runs 19 processes and performs pretty well for its intended purpose. I posted the story so that you could be aware of a possible new piece of malware and how it acts, but I also have a question or two. First, over the last few months I have noticed that PREVX is listed at the top of most of my Google searches when researching malware, especially for new or obscure malware…and they always want you to purchase something. I don’t think they are one of the top AV companies, so it seems odd that they are always the top Google result. Does anyone have any experience with any of their products? Also, what sites do you rely on for malware researching? Recently, I have found it difficult to find good info because of HijackThis-logs and other deadend info cluttering up my searches. And lastly, besides antivirus, third-party firewall, etc, what settings would you use to lock down a machine to make it more secure in instances where a stubborn admin like myself refuses to run AV? Thanks.

  Read the article

• Find/Replace Paragraph End (^13) in Microsoft Word 2007 Merges Paragraphs

  - by Mike Blyth

  I need to replace a target at the beginning of lines with something else. Without wildcards, I can say to replace "^pTarget" with "^pReplacement". With wildcards enabled, I use replace "^13Target" with "^13Replacement". The replacement is successful except that the paragraph is now merged with the previous one in a strange way: The end-paragraph mark is still in place and the paragraph begins on a new line, but Triple clicking to select paragraph selects both the changed paragraph and the one above In a macro, starting in the paragraph above and extending the selection to the end of paragraph causes both paragraphs to be selected. Inter-paragraph spacing disappears between the changed paragraph and the one above. In essence, the paragraph boundary has been removed although the end-paragraph mark is still shown. To duplicate this problem, make a new document Line 1 Line 2 Line 3 (separate paragraphs). Find and replace (with wildcards on) "^13" with "^13". If your result is the same as mine, you will see the problems listed above. I can work around this in the usual way of replacing ^p with something else first, e.g. "^p" = "$", then "$target" = "$replacement", but I'm curious about what's going on. (This is using Word 2007 on Windows 7) I don't know Word XML, but the XML output seems to correspond with the above. Replacing ^13 with ^13 moves the paragraphs together in almost the same way as replacing end-paragraph with end-line (^p = ^l). Here is the relevant XML of the original "Line 1, Line 2, Line 3" in separate paragraphs: <w:p w:rsidR="00BB3032" w:rsidRDefault="00027252"> <w:r><w:t>Line 1</w:t></w:r> </w:p> <w:p w:rsidR="00027252" w:rsidRDefault="00027252"> <w:r><w:t>Line 2</w:t></w:r> </w:p> <w:p w:rsidR="00027252" w:rsidRDefault="00027252"> <w:r><w:t>Line 3</w:t></w:r> </w:p> Now after replacing ^13 with ^13: <w:p w:rsidR="00027252" w:rsidRDefault="00027252"> <w:r><w:t>Line 1</w:t></w:r> <w:r w:rsidR="00C57863"><w:cr/></w:r> <w:r><w:t>Line 2</w:t></w:r> <w:r w:rsidR="00C57863"><w:cr/></w:r> <w:r><w:t>Line 3</w:t></w:r> <w:r w:rsidR="00C57863"><w:cr/></w:r> </w:p> Now original after replacement of ^p with ^l (convert end-paragraph to end-line) <w:p w:rsidR="00027252" w:rsidRDefault="00027252"> <w:r><w:t>Line 1</w:t></w:r> <w:r w:rsidR="00AC7B51"><w:br/></w:r> <w:r><w:t>Line 2</w:t></w:r> <w:r w:rsidR="00AC7B51"><w:br/></w:r> <w:r><w:t>Line 3</w:t></w:r> <w:r w:rsidR="00AC7B51"><w:br/></w:r> </w:p>

  Read the article

• Windows 8.1 Update 1 Disk Usage 100%

  - by Gookjin Jeong

  Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• Optimise Apache for EC2 micro instance

  - by Shiyu Sekam

  I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

  Read the article

• File server share access intermittent/slow/machine unstable: win2kr2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• How to save a ntfs partition which suddenly became empty

  - by SteveO

  One ntfs partition of my laptop was suddenly wiped out without any notice to me, when I rebooted from Windows 7 to Ubuntu 12.04 today. I am in need of help to save my files on that partition, which are important and unfortunately haven't been backed up yet. My laptop has two operating systems: Windows 7 and Ubuntu 12.04. with a ntfs partition shared between the two operating systems for storing some data files (109GB, about 97%of which has been used). I have almost always been using Ubuntu, but today I happened to have to work under Windows. Following is a record of what happened in the time order, numbering according to which operating system I was in at each stage. When I started into Windows 7, right before being able to log in, it took a while and two reboots to configure the Windows. I thought it was normal, since last time when I was using Windows two weeks ago, it took very long and several reboots to update Windows, since the last time I used Windows before then was in November last year. Then after finally being able to log in Windows 7, I installed Libre Office, MathType (I got it from http://dl.portablesoft.org/down/?id=2515, which I originally thought was a trial version, but later I learned was a cracked version and felt wrong. I made a copy of it at dropbox http://dl.dropbox.com/u/13029929/MathType_6.8_PortableSoft.rar, not for distributing it but to list it there just in case it will help to identify the problem), and MikTex. I then edited some .doc files in the ntfs partition under both Microsoft Office with MathType, and Libre Office. When I finished working under Windows and rebooted into Ubuntu, Ubuntu did some filesystem checking and reported that the ntfs partition was not able to be mounted. Then I rebooted again into Windows, and found that the ntfs partition had been emptied, i.e. all the data files were gone, and only one system file bootsqm.dat and one system directory System Volume Information were there, with their last updated time being the time when I first rebooted from Windows to Ubuntu (in fact, it is 4 hours in advanced than the actual time of that rebooting , see immediately below) Also I noticed that the time shown by Windows is not correct for my time zone (UTC-05:00) Eastern Time (US & Canada)), which is 4 hours in advance than the correct time (my current time is 3am, but the computer shows 7am). Same things happened when I rebooted into Ubuntu again: the ntfs has been emptied and left with only one Windows system file bootsqm.dat and one Windows system directory System Volume Information. the time shown by Ubuntu is 4 hours in advance than the correct time. I wonder what I can do to retrieve my data files back on the ntfs partition? If I am not able to do it myself, will some professionals be able to help me out? Thanks a lot! PS: I didn't think I did any thing that required emptying that partition. But there were quite some works I did during that stage right before the reboot from Windows to Ubuntu when the problem occured. Did I make any mis-operation?

  Read the article

• Hard drive write speed - finding a lighter antivirus?

  - by Shingetsu

  I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

  Read the article

• Windows 8 Stuck on Start Screen File Search

  - by baturayd

  I have been searching someone else having the same issue but I couldn't find any. Here is my problem: I'm using Windows 8 Pro with Media Center. File search screen does not close itself after I make a file search within start screen. It stuck on that screen. I can't go back to desktop, therefore, task manager is inaccessible. Only way to get out of it is to sign out. It also looks like non-operational. It doesn't give me any result at all. It's just a blank screen with "Files" title. It used to work perfectly. Things I have done before coming here: Safe mode minimal boot to ensure no other 3rd party software interferes. sfc haven't found any inconsistencies. Search index has been rebuild. Normal boot with all 3rd party services and start-up items disabled. System restore to a date that I know this feature was functional. And by the way, I have installed all updates released so far. I strongly used file search via start menu back in Windows 7. This is an absolute game changer for me. I'm curious what causes this. I'll do a "system refresh" if I can't fix this. I'm working on it, I'll keep this thread updated should I find any fix. First update: I just discovered that file search screen gets stuck if it's invoked by typing query directly in start screen. It doesn't get stuck if it's invoked from win + x menu. I was able to "escape" from stuck screen with invoking it again by win + x menu. After rebuilding search index again, search suggestions started to appear again but still there is no file search functionality. Second update: "Results for" expression appears only for a second near to "Files" title when search is initialized. Third update: As a last resort, I finally tried to do a "System Refresh" which has also failed to refresh by giving an error after waiting almost 20 minutes at 99%. (Seriously?) After cold boot it began to undo changes. After changes were reverted, I boot the machine without doing anything further and bingo! Search began acting normal again. This is a totally weird solution. It obviously fixed certain system files during failed refresh, and kept those changes untouched because they were supposed to be that way at the first place. I'll keep this thread alive should anyone comes with a more logical explanation. Forth update: After a windows update, search functionality again stopped responding. It happened after a system update for the first time. Now I have a pretty good suspicion about system update, though I have no solid proof of its involvement with this problem.

  Read the article

• Please verify my layout: bottom button keeps coming up over keyboard

  - by steff

  Hi everyone, I have a layout which does almost what I want. There's just one bug regarding the button at the bottom. I should stay at the bottom at all times. But whenever I bring up the soft-keyboard the button will be displayed above the keyboard. This is not what I want but it should become covered by the keyboard. Moreover, I'd be happy if you could comment on how the layout's built. Thanks, steff <?xml version="1.0" encoding="utf-8"?> <RelativeLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="fill_parent" android:layout_height="fill_parent" android:orientation="vertical"> <LinearLayout android:id="@+id/l_layout_tags" android:layout_width="fill_parent" android:layout_height="wrap_content" android:orientation="horizontal"> <TextView android:text="TAGS:" android:layout_width="wrap_content" android:layout_height="wrap_content" /> <AutoCompleteTextView android:id="@+id/actv_tags" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_weight="1" android:imeOptions="actionDone" /> <ImageButton android:id="@+id/btn_add_tag" android:layout_width="wrap_content" android:layout_height="wrap_content" android:src="@android:drawable/ic_input_add" android:onClick="addTag"/> </LinearLayout> <ScrollView android:id="@+id/sv_scroll_contents" android:layout_width="fill_parent" android:layout_height="wrap_content" android:layout_below="@id/l_layout_tags" android:scrollbarFadeDuration="2000" > <TableLayout android:id="@+id/t_layout_contents" android:layout_width="fill_parent" android:layout_height="wrap_content" android:stretchColumns="1" android:paddingRight="5dip"> <TableRow android:id="@+id/tr_template"> <ImageView android:id="@+id/iv_blank" android:src="@android:color/transparent" /> <EditText android:id="@+id/et_content1" android:gravity="top" android:maxWidth="200dp" android:imeOptions="actionDone" /> </TableRow> </TableLayout> </ScrollView> <LinearLayout android:id="@+id/l_layout_media_btns" android:layout_width="fill_parent" android:layout_height="wrap_content" android:orientation="horizontal" android:layout_centerHorizontal="true" android:layout_below="@id/sv_scroll_contents" > <ImageButton android:id="@+id/btn_camera" android:layout_width="wrap_content" android:layout_height="wrap_content" android:src="@android:drawable/ic_menu_camera" android:onClick="takePicture" /> <ImageButton android:id="@+id/btn_video" android:layout_width="wrap_content" android:layout_height="wrap_content" android:src="@android:drawable/ic_menu_camera" /> <ImageButton android:id="@+id/btn_audio" android:layout_width="wrap_content" android:layout_height="wrap_content" android:src="@android:drawable/ic_btn_speak_now" /> <ImageButton android:id="@+id/btn_sketch" android:layout_width="wrap_content" android:layout_height="wrap_content" android:src="@android:drawable/ic_menu_edit" /> </LinearLayout> <ImageButton android:id="@+id/btn_save_note" android:layout_width="fill_parent" android:layout_height="wrap_content" android:layout_alignParentBottom="true" android:src="@android:drawable/ic_menu_upload" /> </RelativeLayout>

  Read the article

• Problem with video playback on iPad with MPMoviePlayerViewController

  - by Symo

  Hello everybody... I have been fighting some code for about a week, and am hoping that someone else may have experienced this problem and can point me in the right direction. I am using the MPMoviePlayerViewController to play a video on the iPad. The primary problem is that it works FLAWLESSLY on the iPad Simulator, but will not play at all on the iPad. I have tried re-encoding the video to make sure that isn't an issue. The video I'm using is currently a 480x360 video encoded with H.264 Basline 3.0 with AAC/LC audio. The video plays fine on the iPhone, and also does play through Safari on the iPad. The video actually loads, and you can scrub through the video with the scrubber bar and see that it is there. The frames actually display, but just will not play. If you click play, it just immediately stops. Even when I have mp.moviePlayer.shouldAutoplay=YES set, you can see the player attempt to play, but only for a split second (maybe 1 frame?). I have tried just adding view with the following code: in .h ------ MPMoviePlayerViewController *vidViewController; @property (readwrite, retain) MPMoviePlayerViewController *vidViewController; in .m ------ MPMoviePlayerViewController *mp=[[MPMoviePlayerViewController alloc] initWithContentURL:[NSURL URLWithString:videoURL]]; [mp shouldAutorotateToInterfaceOrientation:YES]; mp.moviePlayer.scalingMode=MPMovieScalingModeAspectFit; mp.moviePlayer.shouldAutoplay=YES; mp.moviePlayer.controlStyle=MPMovieControlStyleFullscreen; [videoURL release]; self.vidViewController = mp; [mp release]; [self.view addSubview:vidViewController.view]; float w = self.view.frame.size.width; float h = w * 0.75; self.vidViewController.view.frame = CGRectMake(0, 0, w, h); I have also just tried to do a: [self presentMoviePlayerViewControllerAnimated:self.vidViewController]; which I actually can not get to orient properly...always shows up in Portrait and almost completely off the screen on the bottom, and the app is only intended to run in either of the Landscape views... If anybody needs more info, just let me know. I'm about at my wits end on this. ANY help will be GREATLY appreciated.

  Read the article

< Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >