Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 248/314 | < Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >

• Remote Desktop Connection issues

  - by stead1984

  I have a server at a remote site, the sites are connected to each other a site-to-site VPN connection using Cisco ASA 5510 firewalls. One end is managed by me, the other managed by the remote location's IT, between the 2 of us is another party who manage and route the connections. Remote desktop has been working fine with no problems then recently I noticed it was working for ONE server over the VPN which it previously had done. All the routes seem fine and I can still ping the remote server and even download files from an FTP site on the remote server.... so the VPN seems fine. Remote Desktop works fine to the remote server within the remote location but not over the VPN. I don't understand why it's stopped working, I originally thought it was a rule in place by the other party but they stress it's not them. The only thing that has changed on the server initiating the RDP connection is that it now runs file services sharing a folder. The source server (remote location) may or may not have had updates applied. Any idea's?

  Read the article

• Arch Linux: eth0 no carrier - network fails at boot

  - by user905686

  The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

  Read the article

• problems installing mysql and phpmyadmin to localhost

  - by Joel

  Hi guys, I know there have been many similar questions, but as far as I can tell, most of the other people have gotten further than I have... I'm trying to get a WAMP setup happening. I've got PHP and Apache running and talking to each other. PHP is in c:\PHP Apache is in it's default program files folder. mySQL is in it's default install location. I have localhost setup at D:\public_html\ I'm able to navigate to localhost and see html and php files. But I have a simple mySQL test file: <?php // hostname or ip of server (for local testing, localhost should work) $dbServer='localhost'; // username and password to log onto db server $dbUser='root'; $dbPass=''; // name of database $dbName='test'; $link = mysql_connect("$dbServer", "$dbUser", "$dbPass") or die("Could not connect"); print "Connected successfully<br>"; mysql_select_db("$dbName") or die("Could not select database"); print "Database selected successfully<br>"; // close connection mysql_close($link); ?> When I try and open this, I get "could not connect" Now, I haven't even created a database yet, because I can't log into mySQL with phpmyadmin-so I think I've done something wrong in my mySQL install because they aren't talking to each other. I guess my main question is how do I first create a database in mySQL to be sure I have even installed it correctly?

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Window 7 Host does not answer to ping

  - by gencha

  Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

  Read the article

• Periodic internet connection drops

  - by sterlingholt

  My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

  Read the article

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Green flickering pixels that move with black images

  - by user568458

  Strange question... Occasionally, on my LCD screen, pixels that should be black flicker rapidly and constantly between black and green, about 4 flickers a second. The crazy part is, unlike dead/stuck pixels, they are relative to content on the screen and move with it. For example, I might be looking at a web page with a picture that has lots of black. There might be a couple of green flashing pixels in that black that shouldn't be there. I scroll the page, and the green flickering pixels move with the image. It seems that everyphysical pixel is fine, but somehow something interprets part of the image in a way that causes flickering green... It's not just in a web browser. My first thought was to blame a trolling blogger cunningly uploading an animated gif that simulates a failing pixel... but it happens in a wide range of applications. It seems to occur randomly, other than that it seems to only occur in areas of pure black, and it's always pure 100% green. It happens rarely enough that it's not a big deal, but it's such a strange problem it bugs me. I can't find any info on anything like this. I'm not even sure if it's hardware or software. Any ideas? (windows 7 laptop connected to LCD by DVI to HDMI cable)

  Read the article

• Mounting any Windows share from OS X 10.7.5 suddenly stopped working

  - by user2169619

  I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• background jobs and ssh connections

  - by petrelharp

  This question has come up quite a lot (really a lot), but I'm finding the answers to be generally incomplete. The general question is "Why does/doesn't my job get killed when I exit/kill ssh?", and here's what I've found. The first question is: How general is the following information? The following seems to be true for modern Debian linux, but I am missing some bits; and what do others need to know? All child processes, backgrounded or not of a shell opened over an ssh connection are killed with SIGHUP when the ssh connection is closed only if the huponexit option is set: run shopt huponexit to see if this is true. If huponexit is true, then you can use nohup or disown to dissociate the process from the shell so it does not get killed when you exit. If huponexit is false, which is the default on at least some linuxes these days, then backgrounded jobs will not be killed on normal logout. But even if huponexit is false, then if the ssh connection gets killed, or drops (different than normal logout), then backgrounded processes will still get killed. This can be avoided by disown or nohup as in (2). There is some distinction between (a) processes whose parent process is the terminal and (b) processes that have stdin, stdout, or stderr connected to the terminal. I don't know what happens to processes that are (a) and not (b), or vice versa. Final question: How can I avoid behavior (3)? In other words, by default in Debian backgrounded processes run along merrily by themselves after logout but not after the ssh connection is killed. I'd like the same thing to happen to processes regardless of whether the connection was closed normally or killed. Or, is this a bad idea?

  Read the article

• Emails not sending from outlook / OWA - Not even hitting the mail queue in exchange

  - by webnoob

  We are having an issue this morning where we can receive external emails but cannot send internal or external ones from Outlook or OWA. If I use: Send-MailMessage –From <[email protected]> –To <[email protected]> –Subject “Test #01”-Body “Just a test message.” –SMTPServer <Server-Name> –Credential <domain\user> the email is sent correctly which makes me think there is a connection issue with OWA and Outlook. However, outlook is reporting as Connected with exchange. I have checked the message tracking in exchange tools and emails sent via outlook and OWA do not appear. Nothing has changed on the server on the weekend so I don't really know where to start debugging this issue. We are using Windows SBS 2011. We only have one send connector which isn't using Smart Hosts and is set to use DNS MX records. Use external DNS is not checked and I can ping google.com etc so doesn't appear to be a DNS issue (plus the email sends from the console anyway). EDIT It appears that users using IMAP can send emails correctly, its only ones that rely on the normal exchange connection type that don't work. EDIT Emails from IMAP are hitting the email queue's where as emails from the normal exchange accounts aren't. EDIT It seems that some of the emails we tried to send yesterday sent at about 1am but now it won't work again..

  Read the article

• How to clone a HDD and then use the clone with VMware (so that Windows works!)?

  - by Ahmad

  I have a system on which Windows 7 is installed, and I am trying to make a clone of its HDD image, which I then want to use in my main PC with VMware, so that I can boot Windows 7 off the cloned HDD. I used Ultimate Boot CD v5.1.1 with the system whose HDD I wanted to clone, and I cloned it using EaseUs Disk Copy, which comes with Ultimate Boot CD. The source HDD was 250 GB in size which had 3 partitions, while the USB HDD I attached to the system, which was supposed to be the destination/clone HDD, was 320 GB in size. I chose to create an exact replica, and so 250 GB worth of data (partitions, etc.) was copied exactly, and the rest of the space was un-allocated. I now connected this USB HDD to my main PC, fired up VMware Workstation 8 and defined a new Virtual Machine, and chose to boot off the USB HDD. Result is that when Windows is booting (from the cloned HDD inside VMware), I get the blue screen error before I reach the login screen. How can I change my methodology so that Windows even boots from the clone? I can change any tools I use, etc.

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• How CPU communicates with HW

  - by b-gen-jack-o-neill

  Good day. I am new here, but I could not find answer to my question using google, so I help I do not violate any rules. So, basically, all I want to ask is, how CPU comminucates with other HW, such as printers, Graphic card, sound card, LAN card etc. I know, that for basic system I/O, you can use BIOS interrupts. INT 10h I believe is for display output. But, what I would like to know is, what actually happens when you execute instruction int 10h. From desription of int instruction, it should jump to routine, which is stored on adress pointed by adress stored in iterrupt table. But how does this routine get into the RAM? Does BIOS save that routines to the RAM? And what actually that routine does? I mean, CPU can only acess RAM, right? So how can now acess some other HW? Is there some special instrucion for it? Or is CPU somehow connected to BIOS, and than BIOS actually does the work? And the last thing, does even OS like Windows or GNU/Linux use BIOS interrupts, or can OS acess HW directly? Thanks.

  Read the article

• Connect to Apache times out randomly

  - by Amadan

  We are trying to set up an Apache server on a remote machine, but we experience strange behaviour. Checking with telnet remote.machine 80, one of these things happen randomly: Connect and serve content normally (no delay) Connect after a long pause Connect normally, then time out without response Timeout on connect Once connected, the request seems to be processed normally. These things do not occur if I connect from that machine directly to localhost 80. The Apache is dedicated, as is the server it runs on (runs only this one application, no-one else is using it for anything else). I am not an administrator of the remote site, and I do not know the network architecture over there, but apparently it's firewalled: (HTTP port is open, SSH port is IP-restricted, most others are closed). If there was any one pattern, I might have some ideas, but this variety of symptoms baffles me. Any ideas as to what could be causing this? Apache is 2.2; Server version is: Linux version 2.6.9-22.ELsmp ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 SMP Mon Sep 19 18:32:14 EDT 2005

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• How to access a port via OpenVpn only

  - by Andy M

  I've set up an openvpn server alongside an apache website that can only be accessed on port 8100 on the same machine. My /etc/openvpn/server.conf file looks like this: port 1194 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/server.crt key ./easy-rsa2/keys/server.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem # Diffie-Hellman parameter server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt # make sure clients can still connect to the internet push "redirect-gateway def1 bypass-dhcp" keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 Now I tried to let only clients connected to the vpn network access the website on apache via port 8100. So I defined a few iptables rules: #!/bin/sh # My system IP/set ip address of server SERVER_IP="192.168.0.2" # Flushing all rules iptables -F iptables -X # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP # Allow incoming access to port 8100 from OpenVPN 10.8.0.1 iptables -A INPUT -i tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # outgoing http iptables -A OUTPUT -o tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT Now when I connect to the server from my client computer and try to access the website on 192.168.0.2:8100, my browser can't open it. Will I have to forward traffic from tun0 to eth0? Or is there anything else I'm missing?

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• RD Gateway reporting features/capabilities

  - by Don

  We have just implemented RD Gateway for our own department in preparation for a push to the whole agency for telecommuting. It is all setup and working great, but I was trying to figure out how best to go about monitoring/reporting of users. I see third party software out there that will do it, but is there anything built-in or via powershell/scripting that I could use that would give me a report of the daily activity of users? Something to say, "User A connected at this time, was on for this long, sent/received this much data"? Basically some of the same stuff you can see in event viewer. Ideally I'd like to be able to have this setup so that once a day it emails me with the daily usage for when a supervisor asks about if their person is actually working (or at least online sending and receiving x amount of data), I'll have some metrics to give them. I realize that actual work output is relevant and more of a managerial issue, but I would like to be able to offer as much as I can from my end when asked. Thoughts? Thanks!

  Read the article

• unable to recover data from failed hdd

  - by Eslam Elyamany

  my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

  Read the article

• Can any iSCSI NAS appliance replicate / clone a LUN to an external drive?

  - by Boden

  I would like to backup using Windows Imaging to some kind of NAS appliance. I believe this will require the NAS to support iSCSI. I would then like the appliance to support the replication of the iSCSI LUN to an external eSATA or USB disk connected directly to the appliance. I've found plenty of NAS appliances that can do iSCSI and replicate to an external drive, but none that I've found thus far can do both at once. That is, the devices can do iSCSI, but then the replication feature doesn't work. The idea here is to backup to an appliance located in a secure office far away from the server room. Offsite backups to external hard drive could be managed from the appliance. The benefits of such a setup would be: 1) very unlikely that fire or random theft would affect both server-room backup and "remote" backup appliance 2) offsite backups could be managed by multiple trusted people without granting access to server room 3) Windows imaging provides poor man's deduplication, so each backup volume can contain a decent backup history. I understand why this would be a non-trivial thing to implement, but I'm wondering if such a thing exists? Preferably a tabletop, low to medium cost device. Alternative solutions welcome. NOTE: I'm backing up very few but very large files, so file replication is not a good option.

  Read the article

• Move a screen session back to its original PID

  - by cron410

  Installed McMyAdmin (minecraft manager) on Ubuntu 12.04 32 bit. Wrote my own service to start McMyAdmin (.net app running in Mono) in its own screen session, and be able to inject proper McMyAdmin commands into that session with the init.d script. Its been running great! Today, I decided to start installing a Source dedicated server (counterstrike pro mod) I determine its going to be a long download process so I quit the process and fire up a fresh screen session called "source". I paste the command in, but it has a space at the begining and bash complains of ignoring semaphores or some such. I detach and reattach the session. Its sliding like butter. I ctrl+a-d out of the session and start exploring the new folder structure and figure out where I need to place a symbolic link. I go to resume that screen and this is what I see: $screen -r source There are several suitable screens on 20091.source (12/02/12 22:59:53) (Detached) 19972.source (12/02/12 22:57:31) (Detached) 917.minecraft (11/30/12 15:30:37) (Attached) It appears I am connected to the minecraft screen?!?!?! So I attach to the other screens one at a time. minecraft is running in 19972.source and sourceds is running in 20091.source So how the hell did I move the minecraft process to another session called source and my main terminal is now "attached" to the minecraft screen? more: I just used exit to quit the putty session, then logged back in, its still the same. did that 3 more times and now the minecraft screen is gone and everything is acting as it should except, of course, for the session name and start time of the "new" minecraft screen. Should I just submit this as a bug for GNU screen?

  Read the article

< Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >