Search Results

Search found 8416 results on 337 pages for 'stop'.

Page 249/337 | < Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >

  • How do I repair a Windows 7 installation damaged by Windows 8 sleep mode

    - by Mat
    I'm experimenting with a Windows 8 installation which is on a separate SSD. My actual Windows 7 installation I'm working with is on my old HDD. While Windows 8 was in sleep mode I swapped the hard disks and put in the Windows 7 HDD (I thought the computer was off). When I started the computer, Windows 8 started back up to the login screen – then it was stuck and some seconds later the computer rebooted. Now the Windows 7 Installation is damaged. When I boot, after the Windows 7 startup logo appears, a bluescreen shows up for few seconds stating: STOP: c000021a {Fatal System Error} The verification of KnownDLL failed. System process terminated unexpectedly with a status of 0xc000012f (0x00f0bb90 0x00000000). The system has been shut down. and then the computer reboots. The same happens in safe mode. 'Windows startup repair' cannot repair the issue. Any idea what could have happened exactly and/or how to repair this Windows 7 Installation?

    Read the article

  • Is Subversion(SVN) supported on Ubuntu 10.04 LTS 32bit?

    - by Chad
    I've setup subversion on Ubuntu 10.04, but can't get authentication to work. I believe all my config files are setup correctly, However I keep getting prompted for credentials on a SVN CHECKOUT. Like there is an issue with apache2 talking to svnserve. If I allow anonymous access checkout works fine. Does anybody know if there is a known issue with subversion and 10.04 or see a error in my configuration? below is my configuration: # fresh install of Ubuntu 10.04 LTS 32bit sudo apt-get install apache2 apache2-utils -y sudo apt-get install subversion libapache2-svn subversion-tools -y sudo mkdir /svn sudo svnadmin create /svn/DataTeam sudo svnadmin create /svn/ReportingTeam #Setup the svn config file sudo vi /etc/apache2/mods-available/dav_svn.conf #replace file with the following. <Location /svn> DAV svn SVNParentPath /svn/ AuthType Basic AuthName "Subversion Server" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user AuthzSVNAccessFile /etc/apache2/svn_acl </Location> sudo touch /etc/apache2/svn_acl #replace file with the following. [groups] dba_group = tom, jerry report_group = tom [DataTeam:/] @dba_group = rw [ReportingTeam:/] @report_group = rw #Start/Stop subversion automatically sudo /etc/init.d/apache2 restart cd /etc/init.d/ sudo touch subversion sudo cat 'svnserve -d -r /svn' > svnserve sudo cat '/etc/init.d/apache2 restart' >> svnserve sudo chmod +x svnserve sudo update-rc.d svnserve defaults #Add svn users sudo htpasswd -cpb /etc/apache2/dav_svn.passwd tom tom sudo htpasswd -pb /etc/apache2/dav_svn.passwd jerry jerry #Test by performing a checkout sudo svnserve -d -r /svn sudo /etc/init.d/apache2 restart svn checkout http://127.0.0.1/svn/DataTeam /tmp/DataTeam

    Read the article

  • Surprising corruption and never-ending fsck after resizing a filesystem.

    - by Steve Kemp
    System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

    Read the article

  • Using Windows Explorer, how to find file names starting with a dot (period), in 7 or Vista?

    - by Chris W. Rea
    I've got a MacBook laptop in the house, and when Mac OS X copies files over the network, it often brings along hidden "dot-files" with it. For instance, if I copy "SomeUtility.zip", there will also be copied a hidden ".SomeUtility.zip" file. I consider these OS X dot-files as useless turds of data as far as the rest of my network is concerned, and don't want to leave them on my Windows file server. Let's assume these dot-files will continue to happen. i.e. Think of the issue of getting OS X to stop creating those files, in the first place, to be another question altogether. Rather: How can I use Windows Explorer to find files that begin with a dot / period? I'd like to periodically search my file server and blow them away. I tried searching for files matching ".*" but that yielded – and not unexpectedly – all files and folders. Is there a way to enter more specific search criteria when searching in Windows Explorer? I'm referring to the search box that appears in the upper-right corner of an Explorer window. Please tell me there is a way to escape my query to do what I want? (Failing that, I know I can map a drive letter and drop into a cygwin prompt and use the UNIX 'find' command, but I'd prefer a shiny easy way.)

    Read the article

  • Windows Service with Logon a user

    - by David.Chu.ca
    I have a service running in a box with Windows XP and a box of Server (2003). There is one service running in autmactic mode. If I set the log on with a local user, the service will stop running if the user logs off the account from the Windows? In other words, in order to keep the service running, have I to keep the user as login mode? I understand that the service can be set as local system which will not need any one to login as long as the box is powered on. However, the service I need to run has to be running as a local user with the required permissions. The problem I have right now is that the box may reboot itself. If that happens, no one is logged in yet until some one has to log in as the required user. I want to make sure if the required user has to be as a log on user first. If that's the case, any suggestion to deal with unexpected reboot issue?

    Read the article

  • Unable to understand why Alfresco doesn't start on Tomcat

    - by Infernalsirius
    Hi all, I have a problem that I've been inspecting for a while now, googling and everything but could not begin to understand. I'm really not used to java, even less tomcat. So there it is. First, the setup. Centos 5.3 on a virtualized server. Bitnami Native Alfresco stack (tomcat5.5, mysql5, java, javajdk, JDBC) Content of catalina.log. Since it's the shortest and where I found my first clue to what is going wrong: SEVERE: Error listenerStart Aug 27, 2009 5:32:58 PM org.apache.coyote.http11.Http11BaseProtocol init INFO: Initializing Coyote HTTP/1.1 on http-8080 Aug 27, 2009 5:32:58 PM org.apache.catalina.startup.Catalina load INFO: Initialization processed in 229 ms Aug 27, 2009 5:32:58 PM org.apache.catalina.core.StandardService start INFO: Starting service Catalina Aug 27, 2009 5:32:58 PM org.apache.catalina.core.StandardEngine start INFO: Starting Servlet Engine: Apache Tomcat/5.5.25 Aug 27, 2009 5:32:58 PM org.apache.catalina.core.StandardHost start INFO: XML validation disabled Aug 27, 2009 5:34:47 PM org.apache.catalina.core.StandardContext start SEVERE: Error listenerStart Aug 27, 2009 5:34:47 PM org.apache.catalina.core.StandardContext start SEVERE: Context [/alfresco] startup failed due to previous errors Aug 27, 2009 5:34:48 PM org.apache.coyote.http11.Http11BaseProtocol start INFO: Starting Coyote HTTP/1.1 on http-8080 Aug 27, 2009 5:34:48 PM org.apache.jk.common.ChannelSocket init INFO: JK: ajp13 listening on /0.0.0.0:8009 Aug 27, 2009 5:34:48 PM org.apache.jk.server.JkMain start INFO: Jk running ID=0 time=0/11 config=null Aug 27, 2009 5:34:48 PM org.apache.catalina.storeconfig.StoreLoader load INFO: Find registry server-registry.xml at classpath resource Aug 27, 2009 5:34:48 PM org.apache.catalina.startup.Catalina start INFO: Server startup in 110327 ms Aug 27, 2009 5:38:27 PM org.apache.coyote.http11.Http11BaseProtocol pause INFO: Pausing Coyote HTTP/1.1 on http-8080 Aug 27, 2009 5:38:28 PM org.apache.catalina.core.StandardService stop INFO: Stopping service Catalina Aug 27, 2009 5:38:29 PM org.apache.coyote.http11.Http11BaseProtocol destroy INFO: Stopping Coyote HTTP/1.1 on http-8080 There's the content of catalina.out, it seems to be a stack trace or application trace of the error, is that right? Catalina.out gist on github There is a 404 error telling me this: The requested resource (/alfresco/) is not available. This is it. I think.

    Read the article

  • Setting "Run WWW service in IIS 5.0 isolation mode" does not persist in IIS 6

    - by Saul Dolgin
    Our IIS server was recently patched with the latest Microsoft Security Updates and since then, I am unable to enable the "Run WWW service in IIS 5.0 isolation mode" setting. This setting was enabled prior to patching and somehow changed during the updates. I have tried both using the IIS Manager console and the adsutil.vbs approach to change it. Either way, after resetting IIS for the change to take effect, when I go to verify that the isolation mode setting is enabled (true) I find that is reverts back to being disabled (false). Now... The patches have already been rolled back, however the setting still does not persist when I enable it. While I am trying to research the patches that were applied to see if there is a known issue (or perhaps a change in this setting's behavior) I was hoping someone else might have come across the same problem. Any help towards a workaround would be greatly appreciated! >cscript adsutil.vbs set W3SVC/IIs5IsolationModeEnabled TRUE IIs5IsolationModeEnabled : (BOOLEAN) True >iisreset Attempting stop... Internet services successfully stopped Attempting start... Internet services successfully restarted >cscript adsutil.vbs get W3SVC/IIs5IsolationModeEnabled IIs5IsolationModeEnabled : (BOOLEAN) False

    Read the article

  • Formatting an external HDD stuck at 70%

    - by mahmood
    My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

    Read the article

  • Balancing internal services using a Cisco CSS 11501

    - by Ladadadada
    First, the background to the problem: I have a Cisco CSS11501 that I am using to load balance a few web servers. These web servers have two network interfaces, one internal and one external and we are sending the requests to the internal interface. We have the CSS configured to do NAT because our webservers need to see the client's IP address. Because the TCP packets hit the webservers with a source address on the Internet, the webserver tries to send the packet back to the client over the external interface and not through the load balancer. In order to stop these requests being sent back out to the Internet via the external interface, we added a routing rule on these boxes so that all traffic with a source address on the internet will use the load balancer as the gateway. This part works fine. What I would also like to to is use the CSS as a load balancer for internal services such as our MySQL slaves. When I do this, I run into a similar problem; the TCP connection goes from the web server to the load balancer and then from the load balancer to the MySQL slave but the CSS spoofs a source address of the original webserver. The MySQL slave then tries to send the response directly to the webserver via the internal network and not via the load balancer. The ideal solution would be to tell the CSS not to do source address spoofing on the internal network and only do it for requests originating on the Internet. Is this possible ? Failing that, is there a way of directing the load balanced traffic back through the load balancer while keeping the other traffic (say SSH) purely on the internal network ? Is there another way of using the CSS11501 to load balance internal services ?

    Read the article

  • How to move a sata drive to a machine without AHCI mode

    - by Andrew Cooper
    I've got a Dell Inspiron 1545 on which the screen has died. I'm able to plug an external monitor into the Inspiron 1545 and it works fine, so the screen is the only issue. The OS is Win7. I'm trying to move the disk to a spare Dell Precision M90 laptop that I've got lying around. The problem is that almost as soon as the Windows logo appears in the boot sequence I get a BSOD with a STOP 0x0000007B message. Researching this message pointed to issues with SATA AHCI mode. I looked in the BIOS of the Inspiron 1545 and the controller was set to AHCI mode. I set it to ATA mode and tried to boot with the same drive and got the same result as on the Precision M90. Switching back to AHCI allowed the machine to boot correctly again. I checked the BIOS on the Precision M90 and it doesn't seem to support AHCI mode, although it is a SATA controller onboard. The BIOS is the latest A08 version available from Dell. Is there any way I can get this drive to boot in the M90 without reformatting it?

    Read the article

  • not able to register sip user on red5server, using red5phone

    - by sunil221
    I start the red5, and then i start red5phone i try to register sip user , details i provide are username = 999999 password = **** ip = asteriskserverip and i got --- Registering contact -- sip:[email protected]:5072 the right contact could be --- sip :99999@asteriskserverip this is the log: SipUserAgent - listen -> Init... Red5SIP register [SIPUser] register RegisterAgent: Registering contact <sip:[email protected]:5072> (it expires in 3600 secs) RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout RegisterAgent: Failed Registration stop try. Red5SIP Client leaving app 1 Red5SIP Client closing client 35C1B495-E084-1651-0C40-559437CAC7E1 Release ports: sip port 5072 audio port 3002 Release port number:5072 Release port number:3002 [SIPUser] close1 [SIPUser] hangup [SIPUser] closeStreams RTMPUser stopStream [SIPUser] unregister RegisterAgent: Unregistering contact <sip:[email protected]:5072> SipUserAgent - hangup -> Init... SipUserAgent - closeMediaApplication -> Init... [SIPUser] provider.halt RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout please let me know if i am doing anything wrong. regards Sunil

    Read the article

  • "Server Unavailable" and removed permissions on .NET sites after Windows Update [closed]

    - by andrewcameron
    Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Spammer relaying via Postfix mail server

    - by Paddington
    I have a Plesk 9.5 mail server (cm.snowbarre.co.za) on Ubuntu 8.04 LTS which forwards all SMTP traffic to an anti-spam server cacti.snowbarre.co.za. Many times I see the headers on the anti-spam server to contain from addresses not hosted on the mail server and I have checked and confirmed that my server is not an open relay server. How can a spammer be using my server to relay spam traffic? How can I stop this? Open relay test: paddington@paddington-MS-7387:~$ telnet cm 25 Trying 196.201.x.x... Connected to cm. Escape character is '^]'. 220 cm.snowbarre.co.za ESMTP Postfix (Ubuntu) mail from:[email protected] 250 2.1.0 Ok rcpt:[email protected] 221 2.7.0 Error: I can break rules, too. Goodbye. Connection closed by foreign host. paddington@paddington-MS-7387:~$ A typical headers is: *Received from cm.snowbarre.co.za (cm.snowbarre.co.za[196.201.x.x]) by cacti.snowbarre.co.za (Postfix) with ESMTPS id 00B601881AD; Mon, 27 Aug 2012 14:03:29 +0200 (SAST) Received from cm.snowbarre.co.za (localhost [127.0.0.1]) by cm.snowbarre.co.za (Postfix) with ESMTP id 81627367E007; Mon, 27 Aug 2012 14:02:50 +0200 (SAST) Received from User (ml82.128.x.x.multilinksg.com [82.128.x.x]) by cm.snowbarre.co.za (Postfix) with ESMTP; Mon, 27 Aug 2012 14:02:49 +0200 (SAST) Reply-To <[email protected]> From "Ms Nkeuri Aguiyi"<[email protected]> Subject Your Unpaid Fund. Date Mon, 27 Aug 2012 05:03:22 -0700 MIME-Version 1.0 Content-Type text/html; charset="Windows-1251" Content-Transfer-Encoding 7bit X-Priority 3 X-MSMail-Priority Normal X-Mailer Microsoft Outlook Express 6.00.2600.0000 X-MimeOLE Produced By Microsoft MimeOLE V6.00.2600.0000 X-Antivirus avast! (VPS 120821-0, 08/21/2012), Outbound message X-Antivirus-Status Clean Message-Id <[email protected]> To undisclosed-recipients:;*

    Read the article

  • Apache randomly looses permission to see files.

    - by arbales
    I have a server (Leopard Server, not my choice) running Apache and MySQL. Several months ago, the server began to raise "Forbidden" errors at random intervals, preventing access to a PHP application. This behavior randomly ceased. Now, several days ago I installed Passenger and deployed a Sintra/Rack application. The application runs as a user acarneg (for example) from /Library/WebServer/Documents/presto/current/public, acarneg owns the entire structure. The _www user has access to the directory via ACL chmod +a "_www allow read,write,...". Everything works great! But after a randomish interval, often ~12 or ~24 hours, Passenger throws an error that also prevents the PHP application from running. Passenger Error #2. Cannot stat file config.ru. Permission denied. But the permissions haven't changed (confirmed) and all one has to do to resolve the error is sudo apachectl graceful. If the permissions aren't changing and Apache doesn't seem to have a legit problem, what is causing this mess? Why did it stop before, and why has it resumed!?!?!? Thanks for the help!

    Read the article

  • VPN issue: SSTP Service service started and then stopped

    - by Ampersand
    When I was trying to set up a VPN connect on my laptop running Windows 7 Ultimate, I got this error: Network Connections Cannot load the Remote Access Connection Manager service. Error 711: The operation could not finish because it could not start the Remote Access Connection Manager service in time. Please try the operation again. I traced through some service dependencies and discovered that Secure Socket Tunneling Protocol Service was set to Manual. However, when I try to manually start the service, I get: Services The Secure Socket Tunneling Protocol Service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. Setting all the services involved to Automatic did not help. SSTP just showed Automatic and Stopped in the Services panel. I found a solution that involved booting in Safe Mode and deleting the contents of C:\Windows\System32\LogFiles\WMI\RtBackup. This solution worked, and I could set up a vpn connection, but only until I rebooted again. TL;DR I'm looking for a way to permanently enable Secure Socket Tunneling Protocol Service and other vpn-related services permanently so I don't have to reboot into safe mode and delete files every time I need to connect to a vpn.

    Read the article

  • How do I create a wifi network bridge with qemu on OS X?

    - by a paid nerd
    I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

    Read the article

  • Upstart: cannot run as root

    - by Ronni Egeriis
    I have made this upstart script, which starts a Node.js service. But all of the sudden the service has stopped, and upstart has failed to restart it. Now that I am trying to start it manually, it fails to recognize my service: start: Unknown job: queue The script is properly placed in /etc/init, and should have the correct rights: -rw-r--r-- 1 root root 200 Aug 7 13:30 queue.conf When I check the config file with init-checkconf however, it says that it is not able to run as root: root@production1:~# init-checkconf /etc/init/queue.conf ERROR: cannot run as root What causes this error and how do I solve it? Debug info: Ubuntu 12.04.3 LTS root@production1:~# service --version service ver. 0.91-ubuntu1 Edit Here's queue.conf: description "Echo.it command queue" author "Ronni Egeriis Persson <[email protected]>" stop on shutdown respawn respawn 20 5 exec sudo -u beanstalk /usr/bin/node /var/www/queue/index.js >> /var/log/queue.log 2>&1 The command sudo -u beanstalk /usr/bin/node /var/www/queue/index.js >> /var/log/queue.log 2>&1 works fine when run manually.

    Read the article

  • Firefox 3.6 and above. Always show one tab even if all tabs are closed like Firefox 3.0

    - by Jayapal Chandran
    I very much got used to Firefox 3.0. In that, to free the memory, I close all tabs but still the main Firefox window does not close. But in Firefox 3.6 and later if I want to close all tabs and if I do so then Firefox totally exists. This is not the case with 3.0. How to stop Firefox from not closing the main process even if I close all threads (tabs)? The autocomplete feature in the address bar of Firefox 3.6 and greater is in a dark blue color which makes me very much annoyed. With my environment and the monitor glare that is inducing anger in me, so how the color be changed to be like Firefox 3.0? Because you know that black and white are a neutral and good combination and since I have been working in Firefox 3.0 (and earlier versions) for a long time this new color change and other uncomfortable options are making me sick. To check CSS3 I need to use Firefox 3.5 and greater. Besides I like Firefox because it includes the W3C's recommendations so I can learn and test new recomendations from W3C.

    Read the article

  • bond0 and xen = crash

    - by Rajat
    Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

    Read the article

  • Auto-rebuild RAID6 with MDADM

    - by user65632
    Hello everybody, i'm new in this forum, and because I see that a lot of people get helped here, i'll ask my question here! I have a openSUSE 11.3 Linux computer with 5 disks of 1TB (WD enterprise disks) in it. with mdadm I configured an RAID6 device. Now, after a lot of thorough testing, i've noticed that when the computer goes down unsuspectedly it could happen (1 time out of 10) that while booting, the md0 device isn't recognised, and then the machine goes in "recovery mode", which means that i have to 'CTRL + C' it so it can boot to openSUSE. Once in openSUSE i have to readd the drive manually with 'mdadm /dev/md0 --add /dev/sdX'. After this everything works back fine (after resynching). So my question is: Is there a way to auto-rebuild the RAID6 device when there are problems? and how can I stop this "recovery mode" from happening. Because the computer will be in a place I can't go to, to connect a keyboard, 'CTRL + C' it just to get in openSUSE. If you could help me, I would be a very very very! happy man! :-) thanks in advance! Mikhail

    Read the article

  • How can I debug a port/connectivity issue?

    - by rfw21
    I am running a simple WebSocket server on Amazon EC2 (Fedora Core). I've opened the relevant port using ec2-authorize, and checked that it's opened. Iptables is definitely not running. However I can't connect to the port from outside EC2. I've tried the following (my server is running on port 7000): telnet ec2-public-dns.xx.xx.xx.amazon.com 7000 (from within EC2: connects fine) nmap localhost (output includes line: 7000/tcp open afs3-fileserver) telnet ec2-public-dns.xx.xx.xx.amazon.com 7000 (this time from my local machine: I get "connection refused: Unable to connect to remote host") The strange thing is this: if I start Nginx on port 7000 then it works and I can connect from outside EC2! And the WebSocket server fails on port 80, where Nginx works fine. To me this suggests a problem with the WebSocket server, BUT I can connect to it successfully from within EC2. (And it works fine on a different VPS account). How can I debug this further? If anybody can stop me tearing my hair out, I'd be very grateful indeed :)

    Read the article

  • WSS Search fills 10 GB limit on SBS server 2011

    - by Kactus
    I've got a SBS Server 2011 Standard SP1 that isn't very busy. 2 Users local and 2 remote. We have sharepoint that has maybe a dozen small documents at most. I've just started getting the following two error occur Could not allocate space for object 'dbo.MSSBatchHistory'.'IX_MSSBatchHistory' in database 'WSS_Search_SERVER' because the 'PRIMARY' filegroup is full. Create disk space by deleting unneeded files, dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. And CREATE DATABASE or ALTER DATABASE failed because the resulting cumulative database size would exceed your licensed limit of 10240 MB per database. Digging around in SQL manager I see that WSS Search DB file size is 10241MB, the log file is only 147 MB Firstly, why is WSS Search taking up so much space? How can I stop it from doing so, and what can I do now to get things running ok. I know about log file truncating and this isn't the case here since the log is tiny. Any help is appreciated. There is plenty of free space on the disk (791GB free) Thanks Kactus

    Read the article

  • `:Zone.Identifier` files keep on appearing in Windows XP virtual machine

    - by Jonathan Reno
    I have a Windows XP Home Edition guest and a Linux Mint 13 host. I use VirtualBox and the ~/Public directory is shared with the guest. It sometimes happens that I use IE on the guest system to download files (until I get a better Windows browser). All of the downloaded files go the the L:\ drive (the ~/Public directory). When they are finished downloading, Windows Explorer adds a :Zone.Identifier file for each file I download. When I extract a downloaded ZIP archive on the guest (on drive L:\), Windows creates a :Zone.Identifier file for every file in the extracted directory. This even occurs if I use the host to move a file to the ~/Public directory. The shared ~/Public directory is on an ext4 partition and the colon character is supposed to be illegal in file names in Windows, but not on the ext4 partition. Is there any way to stop Windows from putting all this rubbish on my filesystem? (I might have to create a shell script to clean up after Windows' act.) Here is what I see in Windows Explorer: By the way, if I were running a Mac OS X host (where colons are illegal file name characters) this would be even more horrendous.

    Read the article

  • IIS6: How to troubleshoot a 404 error in an ASP.NET application?

    - by Tomalak
    I have an ASP.NET application on a Windows Server 2003/IIS6 that refuses to run for some reason (it's the Xerox Centre, if that info helps). It has been working flawlessly before though on this server. Now, all I get if I try to open the app homepage (http://some.intranet.server/XeroxCentreWareWeb/) is a "404 - File or directory not found" error. The app is configured to run in it's own app pool, which runs as Network Service. The Network Service account has read access to the configured directory. If I stop the app pool, I get the expected "Service Unavailable" message, meaning the app and its pool are wired correctly I tried to track down any file permission issues with procmon - nothing to be seen. There isn't even an access to the web app directory happening when the page loads. Interestingly, according to procmon, the web server accesses the 401-2 custom error file (Logon failed due to server configuration) first, but then decides to send the 404 down to the client. EDIT: The app runs with Windows-integrated authentication. Regular users have access to the app directory as well (I would have noticed file system "ACCESS DENIED" messages in procmon, if there had been any.) This makes me think that there is some kind of weird permission problem that occurs even before the application files are being accessed. I just have no idea where to look. I've tried to run the app pool as Local System for a test, but to no avail. What else could I check in this case?

    Read the article

< Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >