Search Results

Search found 4186 results on 168 pages for 'ember router'.

Page 25/168 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

  • Blocking IP address with port forwarding

    - by Jeff Storey
    I have a website setup behind a router, so the router has the external facing address and it will forward requests to the webserver inside the network. If there are X number of invalid login attempts, that IP address will be blocked from logging in. The problem is that because the site is being accessed through port forwarding, all requests show up as though they are coming from the router address, and thus the router address becomes the blocked IP. I'm not sure if this is a limitation of the router (linksys wrt160n) or if this a more general issue. Is there a way to handle this?

    Read the article

  • two computers on same network cannot ping eachother nor view NetBios resources

    - by slava
    I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

    Read the article

  • Why does just splitting an Ethernet cable not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically a one-line communication bus (for argument's sake, I am excluding hubs). All machines attached on the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why would splitting one Ethernet line from my home router into two and connecting two computers not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room, and I had put a computer in another room (also my room, though). Since a wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

  • Is anyone else using OpenBSD as a router in the enterprise? What hardware are you running it on?

    - by Kamil Kisiel
    We have an OpenBSD router at each of our locations, currently running on generic "homebrew" PC hardware in a 4U server case. Due to reliability concerns and space considerations we're looking at upgrading them to some proper server-grade hardware with support etc. These boxes serve as the routers, gateways, and firewalls at each site. At this point we're quite familiar with OpenBSD and Pf, so hesitant at moving away from the system to something else such as dedicated Cisco hardware. I'm currently thinking of moving the systems to some HP DL-series 1U machines (model yet to be determined). I'm curious to hear if other people use a setup like this in their business, or have migrated to or away from one.

    Read the article

  • Why just splitting an Ethernet cable does not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

  • Can only ssh when not using wifi

    - by AChrapko
    So I have 3 machines, a windows 7 desktop that is always wired to my router, osX laptop, and raspberry pi running debian linux. My router is a Linksys e1000 wireless N. My goal is to be able to ssh the raspi from any machine, while it is connected via wifi. My problem is that when trying to ssh from either the win7 or osX to the Pi it either times out, or gives an error: "ssh: connect to host 192.168.1.### port 22: No route to host" The only times that I have managed to connect to the pi from any machine were when it connected to the router via an Ethernet cable. Currently with win7 desktop wired, macbook wireless, and pi wireless tests give the following: win7 ping macbook: Destination host unreachable. macbook ping win7: Request timeout. win7 ping pi: Destination host unreachable. macbook ping pi: Request timeout. blah blah blah Plugging the macbook into the router with an Ethernet cable all communication between win7 and macbook works. Pings, ssh, ftp, smb ect... No changes to the pi, still no connections possible to or from any of the other 2 machines. Note All machines, are able to connect to the internet and ssh to the same machine on a completely different network, wired or over wifi. Plugging the Pi in with Ethernet (and macbook still wired) I can ssh to the pi from both win7 and macbook. I can ssh from the pi to macbook. All machines still able to connect the the off network machine. Also another little side note- I was playing warcraft 3 with my roommates the other day, and the only time they were able to see my LAN game was when they were plugged into the router with an Ethernet cable. Once or twice one of the laptops was able to connect over wifi, but not without another computer connecting first via Ethernet. So basically does anyone have any info as to why my router seems to completely ignore local wireless traffic?

    Read the article

  • How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

    - by Pascal Bourque
    I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

    Read the article

  • How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

    - by Pascal Bourque
    I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

    Read the article

  • SQLAuthority News – Wireless Router Security and Attached Devices – Complex Password

    - by pinaldave
    In the last four days (April 21-24), I have received calls from friends who told me that they have got strange emails from me. To my surprise, I did not send them any emails. I was not worried until my wife complained that she was not able to find one of the very important folders containing our daughter’s photo that is located in our shared drive. This was alarming in my par, so I started a search around my computer’s folders. Again, please note that I am by no means a security expert. I checked my entire computer with virus and spyware, and strangely, there I found nothing. I tried to think what can cause this happening. I suddenly realized that there was a power outage in my area for about two hours during the days I have mentioned. Back then, my wireless router needed to be reset, and so I did. I had set up my WPA-PSK [TKIP] + WPA2-PSK [AES] very well. My key was very simple ( ‘SQLAuthority1′), and I never thought of changing it. (It is now replaced with a very complex one). While checking the Attached Devices, I found out that there was another very strange computer name and IP attached to my network. And so as soon as I found out that there is strange device attached to my computer, I shutdown my local network. Afterwards, I reconfigured my wireless router with a more complex security key. Since I created the complex password, I noticed that the user is no more connecting to my machine. Subsequently, I figured out that I can also set up Access Control List. I added my networked computer to that list as well. When I tried to connect from an external laptop which was not in the list but with a valid security key, I was not able to access the network, neither able to connect to it. I wasn’t also able to connect using a remote desktop, so I think it was good. If you have received any nasty emails from me (from my gmail account) during the afore-mentioned days, I want to apologize. I am already paying for my negligence of not putting a complex password; by way of losing the important photos of my daughter. I have already checked with my client, whose password I saved in SSMS, so there was no issue at all. In fact, I have decided to never leave any saved password of production server in my SSMS. Here is the tip SQL SERVER – Clear Drop Down List of Recent Connection From SQL Server Management Studio to clean them. I think after doing all this, I am feeling safe right now. However, I believe that safety is an illusion of many times. I need your help and advice if there is anymore I can do to stop unauthorized access. I am seeking advice and help through your comments. Reference : Pinal Dave (http://www.SQLAuthority.com) Filed under: SQL, SQL Authority, SQL Query, SQL Security, SQL Server, SQL Tips and Tricks, SQLAuthority News, T SQL, Technology

    Read the article

  • ISC-DHCP not providing address

    - by kiler129
    I just replaced my old router using server with Ubuntu. Everything's fine except DHCP. When I tried connecting iPhone - it works: http://pastebin.com/NNEeiRLY but unfortunately some of my devices can't get IP from server, e.g. my computer: http://pastebin.com/N6LnsEWC Here's my isc configuration: http://pastebin.com/N5KQnhZV I've also tried running DHCP server as root (because of some permission denied in logs on lease file). What can I do?

    Read the article

  • how to access shared external drive connected by usb to Airport Extreme Router

    - by Nathaniel
    I have an external hard drive connected to my Airport Extreme. I keep my photo and music files on it and can access them from both a Mac PowerPC and a Windows XP machine. For some reason I can find, much less connect to, it on my Ubuntu 10.10 machine. I can see my router in the "network" folder but can't seem to find and connect to the shared drive. Any help would greatly appreciated. I am somewhat of a novice with Ubuntu and networking. Thnaks, Nathaniel

    Read the article

  • DD-WRT RIP2 Router mode configuration

    - by Eduardo
    Can anybody tell me why my wireless router only redirects traffic to ADSL modem when it is on Gateway mode? These are the configurations when it is on RIP2 Router mode: ADSL Modem: ------------ LAN IP: 10.1.1.1 Subnet mask: 255.0.0.0 RIP v2 enabled in both directions Route: destination: 192.168.1.0 Subnet mask: 255.255.255.0 Gateway: 10.1.1.2 Wireless Router (DD-WRT) ------------------------ WAN IP: 10.1.1.2 WAN Subnet mask: 255.0.0.0 LAN IP: 192.168.1.1 LAN Subnet mask: 255.255.255.0 Operating mode: RIP2 Router Static Route: Destination LAN NET: 10.0.0.0 Subnet Mask: 255.0.0.0 Gateway: 10.1.1.1 Interface: LAN & WLAN

    Read the article

  • VPN - Cisco 2800 Series Router and Cisco ASA

    - by NickToyota
    What I currently have: Windows 2003/2008 servers supporting a 150 user environment. Linksys RV082 Router (HQ) and RV042 (satellite) routers Site to Site VPN Tunneling to 5 satellite (< 10 user) offices What I need: End-user VPN allowing myself and users to connect remotely to my network I need to replace our current routers and have been recommended the 2811 Router. Can this router alone be enough to get what I need (VPN tunnelling for users and site to site VPN) or will I require purchasing an additional ASA appliance?

    Read the article

  • Wireless Router will not allow connection

    - by Chris
    I am working with a RangeMax(TM) Wireless Router WPN824 v2, and it will not allow a wireless connection nor a wired connection. I am at an actual lost, with no way into the router I cannot test settings. I have unplugged it, left it off for a 32 hours, and reset it with no luck. Any ideas? Could the router just be done-zo?

    Read the article

  • Home network with Windows 7 as router

    - by Michael
    Background: I have tried to use routers, but so far all of them can't handle the bandwidth, number of connections eventually limited by the hardware resources, so overall the home routers are decreasing the internet speed. I went through DD-WRT and stuff like that. Question: What I want is to use my Windows7 PC as router. It has 2 LAN cards. I'm going to connect to this router another desktop 2 pcs and notebook through wireless router. The main question is what is the most efficient way to turn this Windows7 box(and I need Windows for native NTFS support) into router with NAT/Routing/Firewall functionality? Is there any routing software recommended for this purpose or I should just use windows native "Internet Sharing"? I'm going to run SIP phones in the LAN, so I need friendly NAT(Full cone perhaps). Also I'm going to have FTP server on that Windows7 "server" PC. As firewall I'm thinking about Comodo. Need to drop all incoming, unless explicitly allowed.

    Read the article

  • Forward differing hostnames to different internal IPs through NAT router

    - by abrereton
    Hi, I have one public IP address, one router and multiple servers behind the router. I would like to forward differing domains (All using HTTP) through the router to different servers. For example: example1.com => 192.168.0.110 example2.com => 192.168.0.120 foo.example2.com => 192.168.0.130 bar.example2.com => 192.168.0.140 I understand that this could be accomplished using Port Forwarding, but I need all hosts running on port 80. I found some information about IP Masquerading, but I found this difficult to understand, and I am not sure if it is what I am after. Another solution I have found is to direct all traffic to Reverse Proxy server, which forwards the requests onto the appropriate server. What about iptables? I am using a Billion 7404 VNPX router. Is there a feature that this router has that can accomplish this? Are these my only options? Have I missed something completely? Is one recommended over the others? I have searched around but I don't think I am hitting the correct keywords. Thanks in advance.

    Read the article

  • Sharing my broadband connection over a router

    - by user1004985
    I have a broadband connection which I can connect to my laptop's ethernet port. If I want to use the same connection on another machine I would have to do it via a router (I dont want to use ICS since it requires both machines to be ON). I have a router but its uplink is a 4p4c pin rather that an 8p8c(RJ45) so my broadband cable wont fit into it. The router I have is ZTE ZXDSL 531B. And the broadband connection I am talking about has an antenna on the rooftop from which an ethernet cable (CAT 5) runs to my PC's LAN port. Is there some way of utilising the LAN ports of the router to achieve what I mentioned above. Please Help

    Read the article

  • Single-port 2600 router with 2900XL switch

    - by Slava Maslennikov
    I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

    Read the article

  • Host spreads wrong MAC Adress of router on the WIFI

    - by JavaIsMyIsland
    Strange things are going on our network. Since yesterday a host which is actually not on our subnet spreads wrong ARP Replys on our network. To be precise, only on the WIFI. If I connect my Laptop to the cable ethernet, it gets the right MAC adress of the router. Also my Android phone and my Ubuntu system do get the right MAC Adress. So I took a look at wireshark. When I clear the ARP cache of the windows machine, the first ARP response is correct and comes from the router. But like 10 ms later another ARP response comes from another host in the WIFI. The host changes its IP Adresses from time to time and they look like they are not on our subnet. So I can not use the internet because DNS is not working anymore. Sometimes the router wins the race condition and the mac adress is set correctly in the arp cache. I first thought, this is an arp-poisoning mitm attack but it does not make sense if the packets get not routed correctly?! I restarted the router but it didn't help. I have no access to the router, else I would change the shared key to make sure there is no intruder on the wifi.

    Read the article

  • Linksys wireless router will not hardware reset.

    - by Jack M.
    Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

    Read the article

  • Setting up router: I can get online via Ethernet, and I can connect to router wirelessly, but can't

    - by Gabe
    I'm setting up a new D-Link N300 router, and trying to connect a MacBook Pro and a MacBook, both running OS X 10.6. As the question says, either computer can connect to the internet when connected to the router via Ethernet. And either one can get on the router's wireless network. But when connected wirelessly (without the Ethernet cable plugged in), neither one can get online. I can't figure out why that would be. Any help appreciated.

    Read the article

  • VLAN trunking between Juniper EX -> Cisco Catalyst -> and Cisco Router

    - by Hugo Garcia
    I have the following scenario: EX2200 Switch whit ge-0/0/6 set as an access port on VLAN 80 ge-0/0/0 set as a trunk port connected to a catalyst switch and various vlans allowed to pass includin vlan 80 On the Catalyst Switch. port #3 set up as a trunk port that receives traffic from the EX switch. port 46 is set up also as a trunk port that connects to a cisco router. Port #48 is where the host used to be connected host - EX2200 - Catalyst - Router the problem is that this EX2200 is a new addition to the network and the host connected previosly to the catalyst switch. traffic is not getting from the host to the router, but the router can send ARP request to the host. following is the relevant configuration: Catalyst Switch: interface GigabitEthernet1/46 switchport trunk encapsulation dot1q switchport trunk allowed vlan 80,82,83,93,289 switchport mode trunk mtu 1532 media-type rj45 speed 1000 duplex full arp timeout 300 ! interface GigabitEthernet1/48 switchport access vlan 80 switchport mode access mtu 1532 media-type rj45 speed 100 duplex full arp timeout 300 no cdp enable ! EX2200 Switch:

    Read the article

  • Using WDS to make a router act like a makeshift signal booster

    - by cornjuliox
    I've got a router that supports WDS, and I was wondering if I could use it to help extend the range of an existing wireless router? The PC I'm using right now is just barely within the signal range of a wireless router, and the signal is rather weak so I moved my wireless USB adapter away from the computer using a USB extension cord and used a pie tin + some packing tape + a stack of books and a tall wooden stand to make a sort of reflector dish. Sometime in the future I'd like other PCs to be able to connect wirelessly but with the way things are set up I can't move any farther from this spot or I lose the signal entirely. Can I use WDS to bridge the two networks together both to increase the range of the first network and allow computers connected to the 2nd router to share internet access?

    Read the article

  • WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

    - by Gordo
    I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

    Read the article

  • Netgear router keeps disconnecting iPhone

    - by DisgruntledGoat
    My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

    Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >