Search Results

Search found 2489 results on 100 pages for 'hp laserjet'.

Page 25/100 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• rsh connection from Linux to HP times out.

  - by kadeshpa

  I added Linux boxes to /etc/hosts.equiv and .rhosts file for rsh connectivity to HP box. I am able to do rsh as root from Linux to HP. But if I run in a root shell as different user connection times out. Any reason?

  Read the article

• My remote controller is not working.Hp Laptop Dv4 [closed]

  - by Vibin Jith

  I am new with HP. My problem is my remote control is not working. Is there is any driver is required ? if yes which one? i am using Hp Pavilion DV4 1211tu notebook Thank u

  Read the article

• Unable to install Windows 2008R2 x64 on HP ProLiant ML 150 G6 with Smart Array B110i

  - by lrosa

  I am installing Windows 2008 R2 x64 (Microsoft OEM version) on a ProLint ML 150 with Smart Array B110i controller. I load the B110i drivers from a USB thumbdrive, Windows Setup can create, delete and format correctly the partitions on the raidset, but when I exit the disk manager to start setup, Windows says that he cannot find a primary partition to install Windows. The EasySetup disk provided with the system does not support Windows 2008 R2 x64 Microsoft OEM. I downloaded the latest version of EasySetup from HP website, but does not support Windows 2008 R2 x64 Microsoft OEM. Any suggestion?

  Read the article

• Renci.SSHNet and HP ILO 4

  - by Andrew J. Brehm

  I am using Renci.SSHNet to connect to HP iLO processors. Generally this works fine and I can connect and run several commands and disconnect. However, I noticed that a few new servers that use iLO 4 simply don't react to any but the first command sent. When I login using Putty everything works fine, but when using an SSH connection with Renci only the first command sent is recognised whereas the second and further commands do not cause any reaction whatsoever by the iLO processor, not even an error message. Any ideas why that might be?

  Read the article

• NIC Teaming HP Server running Win2003

  - by Colm

  Hello everyone. I'm new to server NIC TEaming. I have a HP ProLiant DL360 G4p running Win2003 with 2 NICs , only one is currently active. I'd like to activate the 2nd NIC connected (in a active/passive state) to a 2nd switch with only one IP address and ideally only one mac layer address. The 1st switch is a Cisco 2960G and the 2nd is a Cisco C3560G. There are VLANS, RSTP and PAGP in use already. Can someone give me an idea, in broad terms , of what technology/protocols I should be investigating (HSRP, SLB/TLB Teaming etc.) ? I can provide more info if needed. Thanks, Colm.

  Read the article

• HP Compaq nc8230 hackintosh?

  - by David

  I have an HP Compaq nc8230 with a Pentium M (1.86GHz, SSE2) 1.5GB RAM, and an ATI Mobility Radeon x600 (64MB dedicated, 596MB shared). I'm trying to install Mac OS X Leopard on it. I have a legal copy of Leopard from apple, so I tried using the generic.iso and putting in the Leo DVD when it tells me to. It gets to the Apple logo with the spinny thing for maybe 5 minutes, but then the computer just restarts. I don't get past the apple logo. Then I tried using iDeneb 1.3 (10.5.5) but it doesn't boot into the DVD. My computer just ignores it and moves onto the hard drive. I would appreciate some help with either methods (moat prefferably the more legal one), I really need an intel Mac, my PowerBook G4 just doesn't cut it.

  Read the article

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• Dual Home HP Server running Win2003

  - by Colm

  Hello everyone. I'm new to server dual homing. I have a HP ProLiant DL360 G4p running Win2003 with 2 NICs , only one is currently active. I'd like to activate the 2nd NIC connected (in a active/passive state) to a 2nd switch with only one IP address and ideally only one mac layer address. The 1st switch is a Cisco 2960G and the 2nd is a Cisco C3560G. There are VLANS, RSTP and PAGP in use already. Can someone give me an idea, in broad terms , of what technology/protocols I should be investigating (HSRP, SLB Teaming etc.) ? I can provide more info if needed. Thanks, Colm.

  Read the article

• How to monitor the temperature of a HP Procurve 3500 switch via SNMP

  - by Murali Suriar

  I am attempting to poll the temperature of an HP ProCurve 3500YL switch remotely using SNMP. Looking at this MIB, it appears that the following OIDs: hpCpuTemperature 1.3.6.1.4.1.11.2.3.7.11.17.7.1.1.1.6 hpPowerSupplyTemperature 1.3.6.1.4.1.11.2.3.7.11.17.7.1.1.1.7 hpChassisTemperature 1.3.6.1.4.1.11.2.3.7.11.17.7.1.1.1.8 Within the 'hpProcurveSysMib' should provide the data I need. However, whenever I attempt to access these OIDs, I receive the response: SNMPv2-SMI::enterprises.11.2.3.7.11.17.7.1.1.1.6 = No Such Object available on this agent at this OID Further investigation reveals that the switch in question does not appear to implement the parent hpProcurveSystem MIB: SNMPv2-SMI::enterprises.11.2.3.7.11.17.7.1.1 = No Such Object available on this agent at this OID Does anyone know of an alternative MIB implemented by the 3500 that will allow its temperature to be polled automatically?

  Read the article

• HP Recovery Manager failed creating a backup disc

  - by Baehr

  I had to restore my computer (running Windows 7) back to its factory default, so I ran the HP recovery manager disc and chose to reformat my computer. Before doing this I was given an option to backup my current files to a DVD, and I did so; getting the confirmation of a successful DVD burn. Booting up my computer everything looks like it did when I first purchased it (like expected). But when I pop in the backup DVD and run the recovery EXE inside it, the application creates a directory inside C:\System Recovery Files which contains the empty directories: [(^_^)] and Program Data. So essentially what I'm getting out of this is a failure in creating a back-up. Which is not only confusing but incredibly frusterating. Is there any way that I can recover the files lost in the

  Read the article

• Disabling RAID feature on HP Smart Array P400

  - by Arie K

  I'm planning to use ZFS on my system (HP ML370 G5, Smart Array P400, 8 SAS disk). I want ZFS to manage all disks individually, so it can utilize better scheduling (i.e. I want to use software RAID feature in ZFS). The problem is, I can't find a way to disable RAID feature on the RAID controller. Right now, the controller aggregates all of the disks into one big RAID-5 volume. So ZFS can't see individual disk. Is there any way to acomplish this setup?

  Read the article

• HP Envy webcam pictures all purple

  - by kousen

  I have a new HP Envy 15 with an integrated webcam, running Win 7. It works, but all the images are purple, suggesting to me that the red and blue guns are working, but the green isn't. The problem shows up on both their own software and on Skype. I talked to tech support, and they had me update the BIOS, reinstall the hardware BIOS for the webcam, and update the webcam software. It therefore sounds like a hardware problem, but they won't back that unless I do a full restore, which would wipe my disk of all the software I've spent the last couple of weeks configuring. Is there anything else I can try? Other than just buying another webcam, I mean. Any suggestions would be appreciated.

  Read the article

• HP dv6000 laptop powers on only if plugged in

  - by Ben

  My HP dv6000 laptop will not run on battery power. It will only run while plugged into the wall. I have already replaced the battery, but it still will not operate on battery power. The problem began slowly. The original battery's life got shorter and shorter, until eventually it would only last ~45 seconds before going into hibernation. Finally, the battery would not work at all, so I threw it out and just used it without a battery. I bought a replacement recently.... but the problem persists. When I connect the new battery to the system, the "charging" light turns on for about 30 seconds, then goes dark. I'm assuming there's something wrong with the internal charging circuitry? If this is the case, how would I go about fixing this, short of buying a new motherboard? If anyone could give me some assistance in confirming/rejecting my diagnosis I'd be very appreciative! :)

  Read the article

• Autonegotiate errors between HP and Cisco hardware?

  - by Satanicpuppy

  This is a bit of a specific extension to this question. I've got two ASA's that feed into a Procurve switch, and then into an IPS. All is well except that the procurve absolutely refuses to autonegotiate with the ASA's...The asa's run 100full, and the procurve autonegotiates to 100half. It does it for both ASA's, so it's probably not a failure on one of them, and everything works fine if I force the procurve to 100full. Has anyone else seen this issue? I've been buying more HP hardware, but I'm not keen on getting equipment that's not going to play nice with my Cisco backbone.

  Read the article

• HP Pavillion dm3 (Windows 7) BSOD,

  - by Lee

  HI I have a HP Pavilion dm3. It came up with a BSOD and then didn't give me an option to start up in safe mode. I dont have any cd drive, nor did it come with a Windows cd anyway. I presume that it has a partition in my laptop for that kinda stuff. I was hoping to boot it using a usb but I don't know how to do it or where to download the stuff from. I have access to network computers, so am able to download from the internet but it's not a Windows7 computer. I am able to download from the computers that I have access to, but unable to run any executable files on them. Can someone please help? Thanks in advance

  Read the article

• Generic socket 940 CPU fan interchangeable with HP part number 411454-001

  - by ConcernedOfTunbridgeWells

  Hi, I'm trying to find a generic CPU fan that will fit the air duct in an XW9300. Note that there are two CPU fan mounting schemes used on this machine. One with two grommets in the motherboard that the CPU fan screws into and one with a plastic collar and base plate. The form factor I'm looking for is the former (see picture below): Two HP part numbers for fans in this form factor are 411454-001 (shown below) and 416055-001. Note that the dimensions are important as the machine has an air duct that fits over the fan. Can anyone tell me the manufacturer and model of an equivalent generic part? Better yet, do you know somewhere (preferrably in the UK) that I can obtain such an item from?

  Read the article

• ATI Driver for HP Pavilion dv2 notebook?

  - by Greg Mattes

  I'm looking for a Windows XP Professional (32-bit) ATI video driver for an HP Pavilion dv2 (model 1118nr). I've downloaded and run several drivers packages, but none have worked so far. The notebook has a sticker on it that reads, "ATI Radeon Premium Graphics 3000 Series" The notebook has an AMD Athlon Neo 64 CPU and it came with Vista 64, but I have a requirement to run 32-bit Windows XP. Does such a driver exist, and if so, where is it? I've tried the AMD ATI graphics drivers portal, but the "Mobility Radeon" section does not list the 3000 series. The "Radeon" section does list the 3000 series, but the package I downloaded and installed from there was not helpful. I also selected "All Graphics - Notebook" on the "Search Drivers and Downloads" page, then selected "Windows XP Professional/Home" on the OS drop down, pressed "Submit", and downloaded and installed the only choice (this single choice is listed twice), but again, it didn't seem to help.

  Read the article

• HP Printer odd behaviour in Vista Home Basic

  - by ricardo.acras

  I Have a HP 1018 printer. In my previous PC (with vista home premium) it worked just fine, and still works. In my new PC, which came with vista home basic, the printing almost never works. What happens is as follows 1 - I install the printer, windows says its ok. 2 - I send a document to print. 3 - Printer screen (spool) shows the document for 1 or 2 seconds and then it disappear. For two times it worked after numerous reinstallations, and after I restart my computer it stop working again. Any Ideas?

  Read the article

• My HP-Vista based laptop has become very slow recently

  - by goldenmean

  My HP laptop which has Vista Home premium. When I try to start Firefox, internet explorer, it becomes very slow. No other app. When i checked the Performance in Task Manager. It shows the Physical memory , Free as 0 bytes, almost always. This has been recently. Earlier it didn't used to be zero. Laptop has 2GB of RAM. I have nothing running in my tray except - Sound control, Laptop power plan indicator,Network status indicator. There are no other processes whose memory usage adds up to so high to make Free memory as 0. Then what could be hogging the memory and make the laptop very slow. Any pointers would help as it is crawling at the moment.

  Read the article

• HP DL380 G5 Predictive Drive Failure on a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

  - by JohnRB

  I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

  Read the article

• Need to upgrade DDR2 RAM on HP Desktop

  - by jds

  I have this HP Pavilion Desktop. As you can see, that page says the memory speed supported is PC2-4200. It currently has a 512 MB stick - CPU-Z Screenshots: hxxp://i41.tinypic.com/j5clj6.jpg and hxxp://i39.tinypic.com/20tldlc.jpg However, a crucial.com scan gives a slightly different report - hxxp://crucial.com/systemscanner/viewscanbyid.aspx?id=5718CFE831D926C3 It says the system can support PC2-5300 memory. So my question is which one should I trust? I want to upgrade the computer's ram to 2 GB (the maximum supported), because XP Media Center is giving me problems and I will install Windows 7 on this. PC2-6400 is the most common DDR2 memory I have been able to find here in the market. Will it cause any problems if I install 2 × 1 GB PC2-6400 DDR2 memory sticks (in dual channel) in this computer, (afaik, it will just run at the lower speed of 533 MHz, or whatever the motherboard supports), or do I absolutely need to get PC2-4200 sticks?

  Read the article

• Adding a CRT display to my HP Mini laptop

  - by Ritwik G

  I tried to add a CRT display to my HP Mini. Here are the details : This is where I thought the display plug must be inserted. This is what the plug looks like: (Please tell me what this thing is actually called. I am pretty sure it is not called a plug. lol) This is where the above plug usually goes into my desktop CPU : Details of my CPU monitor, which I am trying to connect : It did not work :( You can see it not working below: (Yes, the CRT Monitor was switched on) Can this ever work ? How to make this work ?

  Read the article

• Windows XP , HP , IntelInside Trobelshooting

  - by Jamil Hneini

  My Windows XP PC has stopped booting. On start up, before Windows boots a screen appears saying: Windows Could Not Boot: Could Not Find or Corrupted file <Windows root>\Sytem32\Hal.dll Please Reinstall the file... From that I understand that I have to reinstall the OS but my computer is so old that I have lost the backup and recovery disk. My Computer's Info: 32Bit Computer Pentium 4 Windows XP Service Pack 2 HP History: My Computer has 4 hard drives 2 internal 40 GB drives (C And D) 2 external 8GB drives (E And F) Additional Info: I need the files inside C And E The computer reads my flash drive as a hard drive (8.45GB)(I have never booted while my USB pluged in while I was troubleshooting) With some test I discovered that the C drive wasn't detected by the computer I have already configured the boot order of BiOS I have Set The SATA to IDE The Question: I have a setup for windows 8 32 bit how can I boot from my USB to run that setup? If that isn't the proper way to handle this problem please tell me the proper way.

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >