Search Results

Search found 4690 results on 188 pages for 'k ran'.

Page 25/188 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• Confusion on networking service start/stop in Ubuntu

  - by Daniel Ball

  I'm preparing to move and took down two of my servers, leaving only one with some essential services running. What I neglected to consider was that one was the DHCP server(which I realized when somebody contacted me saying they couldn't connect. Whups). So because I only have a few hosts on this small network, I opted to just statically configure them for now. One of these is a new Ubuntu 11.04 server, where I have very little experience. I edited /etc/network/interfaces and /etc/hosts to reflect my changes. I ran $sudo /etc/init.d/networking stop *deconfiguring network interfaces ... So yay. Then I try to start, it gives me the mumbo jumbo about using services (why didn't it do that for the stop?) So instead I run ... $sudo service networking start networking stop/waiting Now, to me that says the status of the service is stopped. But when I ping another computer, I get a successful reply. So is it not actually stopped? More importantly, am I doing something wrong? Edit daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking stop stop: Unknown instance: daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking start networking stop/waiting daniel@FOOBAR:~$ sudo service networking status networking stop/waiting So you can see why I ran /etc/init.d/networking stop instead. For some reason upstart (that is what "services" is, right?) isn't working with stop. cat /etc/hosts 127.0.0.1 localhost 127.0.1.1 FOOBAR 198.3.9.2 FOOBAR #Added entry July 19 2011 # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # hostname FOOBAR auto eth0 iface eth0 inet static address 198.3.9.2 netmask 255.255.255.0 network 198.3.9.0 broadcast 198.3.9.255 gateway 198.3.9.15 No I didn't save backups, it was just a minor change so I just commented out the old DHCP setting. Edit I set everything back to original settings and set up a DHCP server. "starting" networking does the same thing. I can only assume this is normal, I just don't know WHY. It can't be anything to do with the configuration files, since they've been restored.

  Read the article

• cant find nas mediaplayer on vista

  - by user31016

  i have a icy box ib mp3010hw media player i have it on wireless and have it connected to my tp link wr641g router and can access the radio on the net the problem i have is vista sp2 does not see it and i don't know how to go about making it find it. i ran the ping test i think it is by going through Firefox ip addy is 192.168.1.101 and it came up with a simple HTML+cgi example which im assuming means it working. i don't know wot else to do.

  Read the article

• TrueCrypt drive letter not available

  - by Tono Nam

  With c# or a batch file I mount a trueCrypt volume located at A:\volumeTrueCrypt.tc With c# I do: static void Main(string[] args) { var p = Process.Start( fileName:@"C:\Program Files\TrueCrypt\TrueCrypt.exe", arguments:@"/v a:\volumetruecrypt.tc /lw /a /p truecrypt" ); p.WaitForExit(); } the alternative is to run the command on the command line as: C:\Windows\system32>"C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lw /a /p truecrypt Either way I get the error: Why do I get that error? I was able to run that command the first time. The moment I dismounted the volume and tryied to mount it again I got that error. I know that drive letter W is available because it shows as an available letter on true crypt if I where to open it manually: If I where then click on the button mount and then type the password truecrypt (truecrypt is the password) then it will successfully mount on drive w. Why I am not able to mount it from the command line!? If I change the drive letter on the command line it works. I want to use the drive W though. In other words executing "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lz /a /p truecrypt will successfully mount that volume on drive z but I do not want to mount it on drive z I want to mount it on drive w. The first time I ran the batch it ran fine. Also if I restart my computer I believe it should work. More info on how to use trueCrypt through the command line can be found at: http://www.truecrypt.org/docs/?s=command-line-usage Edit I was also investivating when does this error occures. In order to generate this error you need to follow this steps. 1) execute the command: (note the /q argument at the end for quiet) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt /q "C...TrueCrypt.exe" = location where trueCrypt is located /v "path" = location where volume is located /n = drive letter n /p truecrypt = password is "trueCrypt" /q = execute in quiet mode. do not show window note I am mounting to drive letter n 2) now volume should be mounted. 3) Open trueCrypt and manually dismount that volume (without using command line) 4) Attempt to run the same command line (without the /q so you see the error) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt 5) an error should show up So the problem ocures when I manually dismount the volume. If I dismount it from the command line I get no errors. But I think this is a bug from trueCrypt

  Read the article

• MD3200 - 3 to 4x less throughput than MD1220. Am I missing something here?

  - by Igor Polishchuk

  I have two R710 servers with similar configuration. One in my office has MD1220 attached. Another one in the datacenter of my hosting services vendor has MD3200. I'm getting significantly worse throughput from MD3200 at my vendors setup. I'm mostly interested in sequential writes, and I'm getting these results in bonnie++ and dd tests: Seq. writes on MD1220 in my office: 1.1 GB/s - bonnie++, 1.3GB/s - dd Seq. writes on MD3200 at my vendor's: 240MB/s - bonnie++, 310MB/s - dd Unfortunately, I could not test the exactly the same configurations, but the two I have should be comparable. If anything, my good performing environment is cheaper than the bad performing. I expect at least similar throughput from these two setups. My vendor cannot really help me. Hopefully, somebody more familiar with the DAS performance can look at it and tell if I'm missing something here and my expectations are too high. To summarize, the question here is it reasonable to expect about 100MB/s of sequential write throughput per each couple of drives in RAID10 on MD3200? Is there any trick to enable such performance in MD3200 with dual controller as opposed to simple MD1220 with a single H800 adapter? More details about the configurations: A good one in my office: Dell R710 2CPU X5650 @ 2.67GHz 12 cores 96GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.26.1.el5 x86_64 20x300GB 2.5" SAS 10K in a single RAID10 1MB chunk size on MD1220 + Dell H800 I/O controller with 1GB cache in the host Not so good one at my vendor's: Dell R710 2CPU L5520 @ 2.27GHz 8 cores 144GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.11.4.el5 x86_64 20x146GB 2.5" SAS 15K in a single RAID10 512KB chunk size, Dell MD3200, 2 I/O controllers in array with 1GB cache each Additional information. I've also ran the same tests on the same vendor's host, but the storage was: two raids of 14x146GB 15K RPM drives RAID 10, striped together on the OS level on MD3000+MD1000. The performance was about 25% worse than on MD3200 despite having more drives. When I ran similar tests on the internal storage of my vendor's host (2x146GB 15K RPM drives RAID1, Perc 6i) I've got about 128MB/s seq. writes. Just two internal drives gave me about a half of 20 drives' throughput on MD3200. The random I/O performance of the MD3200 setup is ok, it gives me at least 1300 IOPS. I'm mostly have problems with sequentioal I/O throughput. Thank you for looking into it. Regards Igor

  Read the article

• ISAPI filter with LDAP over SSL only works as administrator

  - by Zac

  I have created an ISAPI filter for IIS 6.0 that tries to authenticate against Active directory using LDAP. The filter works fine when authenticating regularly over port 389, but when I try to use SSL, I always get the 0x51 Server Down error at the ldap_connect() call. Even skipping the connect call and using ldap_simple_bind_s() results in the same error. The weird thing is that if I change the app pool identity to the local admin account, then the filter works fine and LDAP over SSL is successful. I created an exe with the same code below and ran it on the server as admin and it works. Using the default NETWORK SERVICE identity for the site's app pool is what seems to be the problem. Any thoughts as to what is happening? I want to use the default identity since I don't want the website to have elevated admin privileges. The server is in a DMZ outside the network and domain where our DCs are that run AD. We have a valid certificate on our DCs for AD as well. Code: // Initialize LDAP connection LDAP * ldap = ldap_sslinit(servers, LDAP_SSL_PORT, 1); ULONG version = LDAP_VERSION3; if (ldap == NULL) { strcpy(error_msg, ldap_err2string(LdapGetLastError())); valid_user = false; } else { // Set LDAP options ldap_set_option(ldap, LDAP_OPT_PROTOCOL_VERSION, (void *) &version); ldap_set_option(ldap, LDAP_OPT_SSL, LDAP_OPT_ON); // Make the connection ldap_response = ldap_connect(ldap, NULL); // <-- Error occurs here! // Bind and continue... } UPDATE: I created a new user without admin privileges and ran the test exe as the new user and I got the same Server Down error. I added the user to the Administrators group and got the same error as well. The only user that seems to work with LDAP over SSL authentication on this particular server is administrator. The web server with the ISAPI filter (and where I've been running the test exe) is running Windows Server 2003. The DCs with AD on them are running 2008 R2. Also worth mentioning, we have a WordPress site on the same server that authenticates against LDAP over SSL using PHP (OpenLDAP) and there's no problem there. I have an ldap.conf file that specifies TLS_REQCERT never and the user running the PHP code is IUSR.

  Read the article

• "Hide from exchange address lists" not working in Exchange 2007

  - by Abdullah

  Hiding a user by checking the "hide from exchange address lists" from exchange management console is not working. The user still shows up in GAL. When I ran Get-Mailbox -Identity _user_ | FL I got HiddenFromAddressListsEnabled : True So the check-box is working but the user still shows up. It's been over 3 weeks since hiding the user so it's not a time issue. This is what I have tried: Using Outlook in online mode Using OWA Regenerating GAL Un-checking then re-checking the "hide" check-box

  Read the article

• Disable MySQL startup in Ubuntu 10.04

  - by bryanhogan

  Hi all, I want to prevent MySQL from starting in Ubuntu 10.04 I have used update-rc.d -f mysql remove and confirmed that there is no link to the /etc/inid.d/mysql script from any of the rc?.d directories. I also ran sysv-rc-conf and it shows me that MySQL is being called as part of the rc.d scripts. It is still starting on boot. How do I disable it? Regards, Bryan

  Read the article

• Windows somehow got convinced that a file is a folder. How do I change it back?

  - by Ben Collins

  I recently moved an external drive from my usb-enabled router to my desktop machine, and ran into some permissions-related issues. A number of files were giving me errors when I tried to take ownership or set permissions, and in all my fiddling on a particular file, it somehow got switched to a folder. Anyone have any idea how this might have happened, and how to flip it back? Here's a screenshot:

  Read the article

• DNS problems with Google on Windows 7

  - by awishformore

  Hello dear superuser community. I had no idea where to post this because it is a problem that completely baffles me. I have a lot of experience with network configuration, but I am completely out of ideas on how to fix this. I have a Fritz!Box branded router on my ISP 1&1 in Germany. My computer is connected to it with a normal Ethernet cable. I always manually set my IP on the computer and use the Google DNS servers for name resolution. I also tried OpenDNS and the result is the same. With that configuration the following happens: Google search responds with big delay Gmail, Google Calendar & Google Drive requests time out the majority of the time In order to troubleshoot, I set the network connection to DHCP for both IP & DNS. At that point, what happens is the following: Google search times out most of the time Gmail, Google Calendar & Google Drive work most of the time Sometimes, it happens that the sites that time out will come up, but weirdly enough, the pictures on the buttons will be missing. For instance, the magnifying glass on Google will be gone or the circle arrow on Gmail (but all buttons of course). All other websites load just fine - and very quickly. All other network functionality is completely unimpacted. The behaviour of fixed IP & Google DNS vs automatic IP & DNS is easily reproducible. I am going crazy trying to fix this as I have no idea what the hell is going on at this point. Here a list of the things I have tried thus far: Flushed the DNS Tried on different browsers (Works fine on my laptop by the way) Tried disabling Teredo & IPv6 stack Emptied all caches Checked the HOSTS file Rebooted the router Reset the router Reinstalled the network adapter Tracert displayes normal route until timing out at one point Ping usually doesn't work for the unreachable sites either Ran both complete Norton 360 & Kaspersky 2012 scan Ran Kaspersky Virus Removal Tool in safe mode Tried connection in safe mode & networking enabled If you have any ideas, please let me know. I'm getting desperate...

  Read the article

• Exchange Server is rejecting message after "MAIL FROM" with "500 5.3.3" with tarpit despite being a Trusted Receiver

  - by Don Rhummy

  I'm getting the message: "500 5.3.3 Unrecognized command" from Exchange server and seeing in the Exchange Server logs that it's tarpitting my smtp sender despite the fact that: I added a Receive Connector for my ip that allows connection, uses "Externally Secure" I ran the commands (with the actual server name): CODE: Set-ReceiveConnector "MyTrusted connector (Servername)" -MaxAcknowledgementDelay 0 Set-ReceiveConnector "MyTrusted connector (Servername)" -TarpitInterval 0 Despite all that, it STILL fails! Any idea what's wrong?

  Read the article

• Disable cookies for selected sites

  - by acidzombie24

  So far all sites have played nice but recently i ran into a site which aggressively tries to get users to sign up and pretty much puts the site on lockdown after 10 pageviews without signing up. What firefox extension can i use to either freeze or disable cookies for this one specific site? I dont want to whitelist every site i visit because one site is giving me trouble.

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• !! 0xc01a00d !! aka Vista won't boot

  - by Chris

  Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

  Read the article

• How to remove bots from my computer?

  - by Nrew

  Because trend micro's rubotted detected that there is a bot running on my system and recommends to run Trend micro's house call to remove the bot. But when I ran house call, it does not detect anything. By the way,my current antivirus software is Microsoft Security Essentials.

  Read the article

• Uninstall Adobe Flash C4 from mac

  - by Nava Carmon

  I've installed a trial of Adobe Flash CS4 (i didn't use this trial till the end) and wrongly entered the expired license number. I ran uninstall and tried to install a trial version again. Seems, that it keeps somewhere the wrong serial number and each time i run the Flash application it alerts me, that the license has expired. How do i properly install the trial? Do i have a chance at all? Thanks a lot!

  Read the article

• OSX Server & Client NFS "timeout" issues?

  - by user36659

  I have a mac environment our server is sharing an NFS mount Setup via Server Admin. Clients connect to the NFS mount at boot via The Directory Utility built into OSX... Everything works fine with one small exception, the NFS mount seems to timeout/dropout every now and then it seems random and requires a reboot to bring it back up? Has anyone else ran into this situation? Any fix would be appreciated.

  Read the article

• NAS device claims drive in a RAID is degraded but S.M.A.R.T. says it is fine

  - by Nathan Villaescusa

  I have a Synology DS213 with two 600GB drives in RAID 1. Last night the device reported that my second drive had become degraded and that I should replace it. When I ran a extensive S.M.A.R.T. test the results said that the drive is okay. How can I confirm that the drive is actually bad? Is there any case that the degraded drive is the good one and that it is actually the other drive that is bad?

  Read the article

• Is there an easy way to copy an audio CD in Mac OS X?

  - by Bob D

  (not a commercial CD). I did some recordings of a band years ago and ran into one of the band members who asked me if I could make copies. I assumed that this would be easy. I know that I can rip the CD into iTunes and then burn a new CD, but I have two optical drives available, is there a way to simply copy the CD from one drive to the other in one step?

  Read the article

• Ubuntu Server 10.04 Heavy Network Traffic causes disconnect

  - by K Vaughan

  I'm currently running a headless Ubuntu 10.04 server. Installed is the LAMP stack, Joomla, Virtualbox, phpvirtualbox, webmin and proFTP.. It resolves the IP address so I can access it remotely (either the apache2 webserver or the FTP) using DDClient. Any packages installed have been installed using apt-get. Webmin, although discouraged in Ubuntu Server, is used mostly to administer the webserver aspect. This issue also appeared when I was using Ubuntu Server 10.10. After periods of heavy network traffic, whether local or remote, the connect drops. I'm talking specifically about the transfer of files via FTP, SCP or Samba (the latter of which I seldom use). There is no response to ping or ssh. I can't FTP to the server nor can I load the website. There are times when the server has been on for a few days and everything runs fine because I haven't accessed it much, if at all (thus not much network traffic). I've gone through a few hardware changes although I don't believe this has cause the issue: this has been happening long before I made any changes. At first I thought it was my ISP-provided router blocking traffic because of some kind of misconfiguration (perhaps assuming it was some kind of DoS attack). I've changed routers and still found no success. I've checked syslog, dmesg and kern.log for warnings but have uncovered none. I've ran memtest via the GRUB2 menu at boot and once it turned up 4 errors. I ran again with individual sticks of RAM in various slots and everything turned up fine. I've looked through the BIOS settings and everything looks fine. I've tried unplugging unnecessary pieces of hardware (other internal hard drives, CD drives, floppy, PCI cards, etc). Any help or tips on how I can even begin to troubleshoot this would be very much appreciated. Please note that i've only started playing with servers as a hobby so my knowledge wouldn't be the most refined. I'm comfortable with command line and have the initiative to know how to look up something I can't do. Unfortunately I can't seem to find any issues like this. Additionally: If a solution can't be found some assistance to write a script that will cause the server to reboot automatically if, after x minutes, it gets no response to pinging somewhere like google. Admittedly that's not the cleanest solution should my internet end up going down but I can't think of what else to do.

  Read the article

• Reg Query Issues

  - by Fitz

  I have a batch script that does reporting on our systems and part of it queries the registry for information. The script fails to get the key's value when its ran by the system, but whenever I run the script myself, it works perfectly the command: REG QUERY "HKEY_LOCAL_MACHINE\SOFTWARE\TrendMicro\ScanMail for Exchange\CurrentVersion" /v PatternStringFormatted > current1.tmp should return: HKEY_LOCAL_MACHINE\SOFTWARE\TrendMicro\ScanMail for Exchange\CurrentVersion PatternStringFormatted REG_SZ 6.645.00 This script is failing on a Server 2008 R2 machine, but runs fine on Server 2003 R2 machines.

  Read the article

• Should I run antivirus application's "full system scan" again in future even I've run when I install

  - by Jitendra vyas

  I use the free AntiVir anti-virus program from Avira. When I installed it I ran a full system scan. should I run the full system scan again in the future even if AntiVir is set to Auto Protect on. Or is there no need to run "full system scan" again if I'm updating virus definitions regularly (auto update).

  Read the article

• How to be compliant with Exchange Basic SAL's

  - by Frederik Nielsen

  I am setting up an environment, where some users are on Standard SAL's, and other are on Basic SAL's. But how do I become compliant with the limitations of the Basic SAL? All they should have access to is: Personal mail folders Personal Contacts Personal Calendar Outlook Web Access Is there any powershell script that I can ran for each user, or a step by step guide to it? I am running Exchange 2010 SP2.

  Read the article

• Error Trying To Use Microsoft LifeCam VX-3000

  - by Brian

  Hello, I bought a Microsoft LifeCam VX-3000 web camera for may parent's Dell Dimension 3000 computer running XP SP 3, and I cannot get it to run. THe installation ran successfully, but when I try to run it, I get the error: Faulting application lifecam.exe, version 3.21.263.0, faulting module kernel32.dll, version 5.1.2600.5781, fault address 0x00012afb. The microsoft help link really didn't help... how do I even resolve this type of error? Thanks.

  Read the article

• Upgrading TFS 2005 to TFS 2010 fails at "Executing servicing step Upgrade Version Control Identities"

  - by nadeemmar

  Hi all, I have been trying to upgrade our TFS 2005 to TFS 2010 but with no luck so far. I went through the TFS Installation guide and many upgrade guides but with no luck in overcoming the issue I am facing which seems to be unique and different to other described issues. In our company, we have a domain forest with several domains. Lets say domain A, B, and C. TFS is in domain A and has users from all these three domains. All domains have trust reltionships between them. However, domain C was deleted several months ago. In the upgrade process, whenever I reach the collection upgrade step, the following error is raised: [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Data: ExtensionType = Microsoft.TeamFoundation.VersionControl.Server.PlugIns.WorkspaceSecurityNamespaceExtension [Info @09:57:50.997] [2010-12-29 09:55:47Z] Servicing step Create VersionControl Security Namespaces passed. (ServicingOperation: UpgradePreTfs2010Databases; Step group: Upgrade.TfsVersionControl) [Info @09:57:50.997] [2010-12-29 09:55:47Z] Executing servicing step Upgrade Version Control Identities. (ServicingOperation: UpgradePreTfs2010Databases; Step group: Upgrade.TfsVersionControl) [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Performer: VersionControl [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Type: UpgradeIdentity [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Data Text: [Error @09:57:50.997] [2010-12-29 09:55:51Z][Error] Sync error for identity: System.Security.Principal.WindowsIdentity, S-1-5-21-1004336348-527237240-682003330-2818 - The trust relationship between the primary domain and the trusted domain failed I looked for the SID and it seems to be for a user in the deleted domain C. With a bit of googling, I figured out that TFSConfig Identities command can be used to remap users from one domain to the other. I went ahead and created local users that matches the users we have from domain C and ran the TFSConfig Identities /Change command and it executed successfully. However, I still get the same error. I am stuck and can't figure out how to move forward :( I need your expertise, has anyone faced this issue before? Do I need to change these identities on TFS 2005 before I commence the upgrade? I forgot to mention, I am following the upgrade with a move approach. I created a virtual machine for testing the upgrade. Installed SQL server 2008, restored the TFS databases and installed TFS 2010 and ran the upgrade wizard. Regards, Nadeem

  Read the article

• DIG command is hanging and not timing out as expected

  - by igalvez

  I ran into the following issue by accident when playing around with the DIG command and testing some domain names. Why does DIG hang and not timeout after 10 seconds when executing the following: dig +tries=1 +tries=1 +retry=1 +time=5 +trace google.us.com DIG hangs for about 30 seconds instead of timing out and then dies with the following error message: dig: couldn't get address for 'ns.reserved-domain.uk.com': no more Do I need to set another flag/option for DIG to have it timeout instead of hanging, or is this a bug? DIG version: DiG 9.9.5-3-Ubuntu

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >