Search Results

Search found 7277 results on 292 pages for 'sound editing'.

Page 25/292 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• Configure audio on HP ENVY 4 ultrabook

  - by phodu_insaan

  I want to configure audio for ubuntu 12.04 on my laptop. Currently the audio just does not play. If i try and plug in headphones then somewhere midway to being fully plugged in the audio plays on the headphones, I plug in further and the sound disappears. How do I get this to work? lspci | grep audio Audio device: Intel Corporation Panther Point High Definition Audio Controller My laptop is one the beats edition HP laptops, and the driver for win7 was an IDT HD audio driver. --EDIT-- The output for cat /proc/asound/card0/codec* | grep Codec is Codec: IDT 92HD91BXX Codec: Intel PantherPoint HDMI I need to get both the IDT card to work and the HDMI card to work with my TV. --EDIT-- --EDIT 2-- I have added blacklist snd-usb-audio to the end of the file /etc/modprobe.d/alsa-base.conf Now the sound plays from my laptop speakers only when I plug in a headphones/external speaker. Otherwise no sound. :( Please help getting everything working as it should. --EDIT 2-- Thanks

  Read the article

• Bluetooth Audio and SoftPhone Audio Input/Output

  - by o7th Web Design

  I have a Voip Softphone software that I would like to start using on my Ubuntu 14.04 box. Here's the thing. My system sound right now goes through my HDMI to my speaker system so I can play music all day ;-) I have a bluetooth headset connected to the machine as well. What I am wondering is if there is a way to: Auto-mute the music when a call comes in Auto-switch the sound devices when a call comes in, from my hdmi sound device, to my headset Auto-switch back when the call ends, and auto-un-mute the music Or even just an auto-switch to the headset? I can always pause the music ;)

  Read the article

• No analog audio in 13.10

  - by danepowell

  I've installed 13.10 on a machine that was previously running Windows 8, and audio output isn't working out of the box. It worked fine in Windows, and the speakers work fine when hooked up to a laptop, so it must an incompatibility between Ubuntu and the motherboard. If I go to sound settings, "Built-in Audio" is selected (SPDIF is also available). This is an Intel Z77 motherboard with an integrated Creative CA0132 sound chipset. I've tried booting a live image of 13.10 (to check for a corrupt install), and the same problem exists. If I boot a live image of 13.04, the only audio output listed in sound settings is a "dummy" card. I've already tried basic troubleshooting steps, such as removing pulseaudio config directories, force-restarting alsa, and making sure the speakers aren't muted in the alsa mixer. At this point, I'm totally stumped :(

  Read the article

• How can I play different sounds each time I startup?

  - by user82171

  I have read questions on Changing startup sound in Ubuntu and Changing startup music in Ubuntu. I understand how to rename 'desktop-login.ogg' and copy the sound I want as 'desktop-login.ogg'. My question is - is there a way I can play different sounds each time I login? It may sound silly, but if possible I would like to play different sounds. I am guessing that this may be perhaps possible by running some kind of script which replaces/renames the desktop-login.ogg file each time I shutdown, so that a new file is ready to be played on the next startup. But I don't know how to copy a new file from a particular folder to desktop-login.ogg upon each shutdown, nor do I know where the script should reside. I would appreciate it if someone could tell me how to do it, or if there is an easier way of doing this. Thank you

  Read the article

• low volume/dual boot

  - by user2367

  I have an intel Imac dual-booting Ubuntu 10.04 and OSX 10.6. Both work fine, but sound is very quiet in Linux, even though the gnome volume control panel and pulse audio volume control panels are both set to 100%. I can turn the speaker volume up and it's fine, but then when I boot back to OSX the volume makes me jump out of my skin. Is there a setting I'm missing? If I turn the gnome sound pref volume higher then 100, it tends to distort the sound. (crackling)

  Read the article

• USB audio device not detected [solved]

  - by user199052

  I've been having problems with USB sound for some time (it used to work about 6 months ago). I find that any USB sound device that I connect is not recognised, and is not listed by aplay -l I've tried disabling pulseaudio. I've tried purging and re-installing alsa-base, pulseaudio, and pavucontrol. To no avail. I'm using 12.04 LTS. I found the solution: 12.04 does not have the needed kernel module snd-usb-hiface this is introduced in the 3.11.1 kernel and installing that on 12.04 gives USB sound for my equipment. How to install the 3.11.1 kernel is given here:- installing 3.11.1 kernel

  Read the article

• HTML5 and CSS3 Editing in Windows Live Writer

  - by Rick Strahl

  Windows Live Writer is a wonderful tool for editing blog posts and getting them posted to your blog. What makes it nice is that it has a small set of useful features, plus a simple plug-in model that has spawned many useful add-ins. Small tool with a reasonably decent plug-in model to extend equals a great solution to a simple problem. If you're running Windows, have a blog and aren’t using Live Writer you’re probably doing it wrong…One of Live Writer’s nice features is that it can download your blog’s CSS for preview and edit displays. It lets you edit your content inside of the context of that CSS using the WYSIWYG editor, so your content actually looks very close to what you’ll see on your blog while you’re editing your post. Unfortunately Live Writer renders the HTML content in the Web Browser Control’s  default IE 7 rendering mode. Yeah you read that right: IE 7 is the default for the Web Browser control and most applications that use it, are stuck in this modus unless the application explicitly overrides this default. The Web Browser control does not use the version of Internet Explorer installed on the system (IE 10 on my Win8 machine) but uses IE 7 mode for ‘compatibility’ for old applications.If you are importing your blog’s CSS that may suck if you’re using rich HTML 5 and CSS 3 formatting. Hack the Registry to get Live Writer to render using IE 9 or 10In order to get Live Writer (or any other application that uses the Web Browser Control for that matter) to render you can apply a registry hack that overrides the Web Browser Control engine usage for a specific application. I wrote about this in detail in a previous blog post a couple of years back.Here’s how you can set up Windows Live Writer to render your CSS 3 by making a change in your registry:The above is for setup on a 64 bit machine, where I configure Live Writer which is a 32 bit application for using IE 10 rendering. The keys set are as follows:32bit Configuration on 64 bit machine:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Microsoft\Internet Explorer\Main\FeatureControl\FEATURE_BROWSER_EMULATIONKey: WindowsLiveWriter.exeValue: 9000 or 10000  (IE 9 or 10 respectively) (DWORD value)On a 32 bit only machine: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\Main\FeatureControl\FEATURE_BROWSER_EMULATIONKey: WindowsLiveWriter.exeValue: 9000 or 10000  (IE 9 or 10 respectively) (DWORD value)Use decimal values of 9000, 10000 or 11000 to specify specific versions of Internet Explorer. This is a minor tweak, but it’s nice to actually see my blog posts now with the proper CSS formatting intact. Notice the rounded borders and shadow on the code blocks as well as the overflow-x and scrollbars that show up. In this particular case I can see what the code blocks actually look like in a specific resolution – much better than in the old plain view which just chopped things off at the end of the window frame. There are a few other elements that now show properly in the editor as well including block quotes and note boxes that I occasionally use. It’s minor stuff, but it makes the editing experience better yet and closer to the final things so there are less republish operations than I previously had. Sweet!Note that this approach of putting an IE version override into the registry works with most applications that use the Web Browser control. If you are using the Web Browser control in your own applications, it’s a good idea to switch the browser to a more recent version so you can take advantage of HTML 5 and CSS 3 in your browser displayed content by automatically setting this flag in the registry or as part of the application’s startup routine if not dedicated setup tool is used. At the very least you might set it to 9000 (IE 9) which supports most of the basic CSS3 features and is a decent baseline that works for most Windows 7 and 8 machines. If running pre-IE9, the browser will fall back to IE7 rendering and look bad but at least more recent browsers will see an improved experience.I’m surprised that there aren’t more vendors and third party apps using this feature. You can see in my first screen shot that there are only very few entries in the registry key group on my machine – any other apps use the Web Browser control are using IE7. Go figure. Certainly Windows Live Writer should be writing this key into the registry automatically as part of installation to support this functionality out of the box, but alas since it does not, this registry hack lets you get your way anyway…Resources.reg Files to register Live Write Browser Emulation (set for IE9)Specifying Internet Explorer Version for ApplicationsSnagIt LiveWriter Plug-inDownload Windows Live WriterDownload Windows Live Writer with Chocolatey© Rick Strahl, West Wind Technologies, 2005-2013Posted in Live Writer  Windows   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• Playing sound on server using php

  - by Lorenz

  I want to play a sound file on my server using PHP. The PHP script is called by Apache and runs under the user 'nobody', which has by default no access to the speakers. So I created a new user soundoutput which is allowed do play sound and has read permissions for the sound files he should play. If I'm logged in as root, I can play a sound file using echo password | sudo -Su soundoutput mpg321 '/path/to/sound.mp3'. The problem is, that it doesn't work when I'm executing this command using PHP's system_exec. I guess that user nobody isn't allowed to run sudo, but what can I do that he is allowed to do that? Any help appreciated.

  Read the article

• Using .NET C#, I need to create a simple program that responds whenever it picks up any sound from t

  - by David

  I am trying to create a program that will sit and wait until it picks up on any sound (i.e. a doorbell), and in response, triggers an event function that I can use to run some code. My exact goal is to have it run wmplayer playing a sound of a dog barking whenever it picks up something as loud as a doorbell from the microphone input. Thanks! --David

  Read the article

• Add a “Textmate Style” Lightweight Text Editor with Dropbox Syncing to Chrome and Iron

  - by Asian Angel

  Are you looking for a good text editing environment with Dropbox syncing built in for your browser? If the answer is yes, then you should definitely give the SourceKit – Text Editor Inside Chrome web app a try. Once SourceKit has finished installing you will need to log into your Dropbox account if you have not already done so. Note: Dropbox login tab will automatically open for your convenience. When the login process is complete you will need to authorize access for SourceKit to sync up with your account. After you authorize access you can switch back to the SourceKit tab and see a complete listing of your Dropbox files available on the left side. Note: Sidebar width is adjustable. Just choose a file to start editing it as desired. You can modify how the interface looks and acts using the controls at the top of the editing window. The tab bar UI also lets you work on multiple documents at the same time. Note: The .crx install file is 5.2 MB in size and SourceKit will take a few moments to get settled in once the file is downloaded. SourceKit – Text Editor Inside Chrome [Chrome Web Store] Latest Features How-To Geek ETC Learn To Adjust Contrast Like a Pro in Photoshop, GIMP, and Paint.NET Have You Ever Wondered How Your Operating System Got Its Name? Should You Delete Windows 7 Service Pack Backup Files to Save Space? What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions Add a “Textmate Style” Lightweight Text Editor with Dropbox Syncing to Chrome and Iron Is the Forcefield Really On or Not? [Star Wars Parody Video] Google Updates Picasa Web Albums; Emphasis on Sharing and Showcasing Uwall.tv Turns YouTube into a Video Jukebox Early Morning Sunrise at the Beach Wallpaper Data Networks Visualized via Light Paintings [Video]

  Read the article

• Sound not playing on Windows XP - SoundEffect or Song: Monogame

  - by ashes999

  I'm trying to integrate sound into my Monogame game. I don't have the content pipeline hack -- just straight Monogame (Beta 3) at this point. (I tried adding the content pipeline, but ran into some issues.) I added a .wav file to my /Content directory, and I can create and instantiate both SoundEffect and Song classes. However, both show durations of 00:00:00 (on a ten-second long file), and neither plays. I can call LoadContent without any issue. But when I call Play, nothing plays. I've tried a couple of different sounds, and different formats (MP3 and WAV) to rule that out. Only WAV seems to even load without crashing out, but it doesn't play. There seems to be a GitHub issue that fixes this problem in 2.5.1. Downgrading to 2.5.1 doesn't fix this problem; it seems like it's fixed in 3.0 (_data is set in the SoundEffect instance). This issue only occurs on Windows XP. I tested it on a Windows 7 laptop, and the sound plays fine.

  Read the article

• Game: Age of Empires sound good but video "out of range"

  - by Ezekiel

  I'm new to the Ubuntu realm. Currently i'm using Linux Mint 12 with Wine 1.4 and PLAYONLINUX as game loading/playing programs. Video card is MSI GeForce FX5200 (NVIDIA) and is 3d enabled. I can play "Call of Duty 5 demo just fine. My real love is the Age of Empires series games. I loaded the WINE version of AOE 1 demo. No sound and no picture. Black screen with "Out of Range" window in red. I loaded my CD version of AOE 1 through PLAYONLINUX. I get the sound just fine but again the black screen with "Out of Range" window in red. I have used all the monitor settings in both the "settings" and in winecfg. None of the eight monitor options worked in any combination. I have checked all the questions and blogs on this error and tried all I found and no one seems to come up with a real fix. I guess I need to know exactly what the "Out of Range" means. Any help? Anywhere? Thanks

  Read the article

• Sound card not detected in 13.04

  - by Ganessh Kumar R P

  I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

  Read the article

• Play sound on menu items on hover [migrated]

  - by Mahalia Samuels

  How can I go about making a sound clip play when an element is hovered over? I'm using the latest Wordpress, and the parent theme I am using gives me an option to paste scripts which it will embed to the <head> section. Is there a script which I can just add to my <head> that will play the sound when the cursor moves over my menu item class .menu li? I spent several hours trying to figure this out the other day with no avail. I've done this before in a simple HTML website: <head> <script language="javascript" type="text/javascript"> function playSound(soundfile) { document.getElementById("dummy").innerHTML= "<embed src=\""+soundfile+"\" hidden=\"true\" autostart=\"true\" loop=\"false\" />"; } </script> </head> <li><a href="index.html" onmouseover="playSound('lib/hover.mp3');" onclick="playSound('lib/click.mp3');"><span>Home</span></a></li> Not sure how to deploy this on Wordpress though.

  Read the article

• Mplayer no sound when playing some movies

  - by Ivan Peevski

  Ok, that's a bit of a strange problem, that somehow crept into my system. It used to work fine. Here is the problem as far as I can identify it. When I try to play certain video files with mplayer, there is no sound. As far as I can tell, it is only an issue with ac3 and dts sound tracks (using the ffmpeg decoder). Mplayer says: ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders AUDIO: 48000 Hz, 6 ch, s16le, 1536.0 kbit/33.33% (ratio: 192000->576000) Selected audio codec: [ffdca] afm: ffmpeg (FFmpeg DTS) ========================================================================== [AO_ALSA] Playback open error: Device or resource busy Failed to initialize audio driver 'alsa' Could not open/initialize audio device -> no sound. Audio: no sound (similar with ac3 sound, but using the ffac3 audio codec). Trying different audio output (-ao oss/pcm/sdl) doesn't fix the problem. The strange thing is that if I play these files directly with ffplay, they work fine. mplayer sound with mp3/ogg is fine My alsa configuration is standard (no /etc/asound.conf or ~/.asound*) OS: Linux Gentoo Mplayer: 1.0_rc4_p20100213 (SVN-r30554-4.3.4) FFMpeg: 0.5_p20601-r1 (SVN-r20601) Any other information I can provide?

  Read the article

• Windows 8 Communication Sound Setting not working

  - by blackmastiff

  I've been having a problem on my new laptop recently which is familiar but baffling the usual fixes. I'm running Windows 8 with an onboard Realtek soundcard. It's similar to the one on my older computer running Windows 7. The problem is, when I'm in Skype or Mumble, Windows changes the sound output to lower everything else automatically. I've disabled the communications sound change option on the communications tab within sound devices and checked all the applications settings to insure that they are not responsible. They aren't, and I noticed something else. When I'm in the sound properties dialog, and I switch to the microphone tab, the same audio output reduction occurs. This seems to say to me that the microphone must be responsible in some way, but seeing as I uninstalled all the drivers and installed windows drivers instead, I'm confused as to why this would be occurring. Any thoughts? EDIT: I just tried disabling the built in microphone and the sound no longer get changed. More confused now? As soon as I turn it back on, the sound gets dropped again. Incidentally, the fix for this on windows 7 was this question: Windows 7 lowers applications' volume automatically I've got my computer set that way and it doesn't work.

  Read the article

• Super-Charge GIMP’s Image Editing Capabilities with G’MIC [Cross-Platform]

  - by Asian Angel

  Recently we showed you how to enhance GIMP’s image editing power and today we help you super-charge GIMP even more. G’MIC (GREYC’s Magic Image Converter) will add an impressive array of filters and effects to your GIMP installation for image editing goodness. Note: We applied the Contrast Swiss Mask filter to the image shown in the screenshot above to create a nice, warm sunset effect. To add the new PPA open the Ubuntu Software Center, go to the Edit Menu, and select Software Sources. Access the Other Software Tab in the Software Sources Window and add the first of the PPAs shown below (outlined in red). The second PPA will be automatically added to your system. Once you have the new PPAs set up, go back to the Ubuntu Software Center and do a search for “G’MIC”. You will find two listings available and can select either one to add G’MIC to your system (both work equally well). Click on More Info for the listing that you choose and scroll down to where Add-ons are listed. Make sure to select the Add-on listed, click Apply Changes when it appears, and then click Install. We have both shown here for your convenience… When you get ready to use G’MIC to enhance an image, go to the Filters Menu and select G’MIC. A new window will appear where you can select from an impressive array of filters available for your use. Have fun! Command Line Installation For those of you who prefer using the command line for installation use the following commands: sudo add-apt-repository ppa:ferramroberto/gimp sudo apt-get update sudo apt-get install gmic gimp-gmic Links Note: G’MIC is available for Linux, Windows, and Mac. G’MIC PPA at Launchpad [via Web Upd8] G’MIC Homepage at Sourceforge *Downloads for all three platforms available here. Bonus The anime wallpaper shown in the screenshots above can be found here: anime sport [DesktopNexus] Latest Features How-To Geek ETC Learn To Adjust Contrast Like a Pro in Photoshop, GIMP, and Paint.NET Have You Ever Wondered How Your Operating System Got Its Name? Should You Delete Windows 7 Service Pack Backup Files to Save Space? What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions Access and Manage Your Ubuntu One Account in Chrome and Iron Mouse Over YouTube Previews YouTube Videos in Chrome Watch a Machine Get Upgraded from MS-DOS to Windows 7 [Video] Bring the Whole Ubuntu Gang Home to Your Desktop with this Mascots Wallpaper Hack Apart a Highlighter to Create UV-Reactive Flowers [Science] Add a “Textmate Style” Lightweight Text Editor with Dropbox Syncing to Chrome and Iron

  Read the article

• Editing Project files, Resource Editors in VS 2010

  - by rajbk

  Editing Project Files Visual Studio 2010 gives you the ability to easily edit the project file associated with your project (.csproj or .vbproj). You might do this to change settings related to how the project is compiled since proj files are MSBuild files. One would normally close Visual Studio and edit the proj file using a text editor.  The better way is to first unload the project in Visual Studio by right clicking on the project in the solution explorer and selecting “Unload Project”   The project gets unloaded and is marked “unavailable” The project file can now be edited by right clicking on the unloaded project.    After editing the file, the project can be reloaded. Resource editors in VS 2010 Visual studio also comes with a number of resource editors (see list here). For example, you could open a file using the Binary editor like so. Go to File > Open > File.. Select a File and choose the “Open With..” option in the bottom right.   We are given the option to choose an editor.   Note that clicking on the “Add..” in the dialog above allows you to include your favorite editor.   Choosing the “Binary editor” above allows us to edit the file in hex format. In addition, we can also search for hex bytes or ASCII strings using the Find command.   The “Open With..” option is also available from within the solution explorer as shown below: Enjoy!   Mr. Incredible: No matter how many times you save the world, it always manages to get back in jeopardy again. Sometimes I just want it to stay saved! You know, for a little bit? I feel like the maid; I just cleaned up this mess! Can we keep it clean for... for ten minutes!

  Read the article

• Where is /dev/dsp or /dev/audio?

  - by YumYumYum

  I have to apply sudo chmod a+r /dev/dsp or /dev/audio but in my Ubuntu 12.10 i do not have such. Where is then the PCM sound file for ssh? chmod: cannot access `/dev/dsp': No such file or directory chmod: cannot access `/dev/audio': No such file or directory Follow up: http://superuser.com/questions/244173/missing-dev-dsp-under-ubuntu I want to stream the sound output and input. So that i can capture any audio in/out to a file for recording.

  Read the article

• Volume range is narrow in 12.04

  - by Alejandro

  I have upgraded to Ubuntu 12.04 and I have a problem with the volume. The problem is that the volume is 0 when the volume bar is between 0% and 66% more or less, so the actual volume range is only between 66% and 100%. If I open the sound configuration menu, the position in the volume bar that makes the sound begin sounding (66% more or less) is placed where it says "no amplification". Can anyone help me? Thank you.

  Read the article

• How can I reinstall pulseaudio? (12.04 64bit)

  - by Luca Cerone

  I accidentally removed pulseaudio from my Ubuntu 12.04 64bit. I have tried reinstalling it using sudo apt-get install pulseaudio but my sound card doesn't appear in the list of the devices (in System Settings -- Sound). For the moment I managed to get sounds by using ALSA, but I would like to reinstall pulseaudio and have it working as before my accidental removal. How can I reinstall it and have the devices configured correctly?

  Read the article

• How to activate subwoofer in Inspiron 17r?

  - by alfC

  I have a Dell Inspiron 17r, after a fresh install of 12.10, the subwoofer seems to be not utilized. No sound comes from it and in the Sound Control Panel the settings appear grayed out (see screenshot). How can I activate the subwoofer? I tried adding the line options snd-hda-intel model=dell in the file /etc/modprobe.d/alsa-base.conf and enable-lfe-remixing = yes default-sample-channels = 3 in the file /etc/pulse/daemon.conf, but still doesn't work.

  Read the article

• OWB 11gR2 &ndash; OMB and File Editing

  - by David Allan

  Here we will see how we can use the IDE for editing OMB scripts. The 11gR2 release is based on the common Oracle platform IDE used also by JDeveloper. It comes with a bunch of standard behavior for editing and rendering code. One of the lesser known things is that if you drop a text file into OWB you can edit it. So you can drop your tcl scripts right into OWB and edit in-place, and don’t need another IDE like Eclipse just for this task. Cool, so you have the file here. There may be no line numbers, you can toggle line numbers on by right clicking in the gutter. If we edit the file within the OWB IDE, the save is a little different from normal. OWB doesn’t normally manipulate files so things like ctrl-s to save, saves the OWB objects, but if you edit a file the closing of the file will ask if you want to save it – check it out. Now we enter the realm of ‘he who dares’…. Note the IDE doesn’t know about tcl files out of the box, so you see above there is no syntax highlighting. The code is identified by the extension… .java is java, .html is HTML etc. With OWB, the OMB scripts are tcl, we usually have .tcl extension on these files. One of the things we can do to trick up the syntax highlighting is to simply rename the file to have a .java suffix, then all of a sudden we get syntax highlighting, see the illustration here where side by side we see a the file with a .java extension and a .tcl extension. Not ideal pretending to be .java but gets us a way to having something more useful than notepad. We can then change the syntax highlighting such that we get Eclipse like highlighting within the IDE from the Tools Preferences option; You then get the Eclipse like rendering albeit using a little tweak on the file names… Might be useful if you are doing any kind of heavy duty OMB script development and just want a single IDE. The OMBPlus panel is then at hand for executing and testing it out.

  Read the article

• How to associate hardware volume control to USB speakers?

  - by Wolfger

  My Xubuntu system recognizes my speakers, and I can change the mixer settings to make them the active sound device, but no matter what I do, the hardware dial will only affect the onboard sound device. generic-usb 0003:046D:0A19.0003: input,hidraw1: USB HID v1.00 Device [ Logitech Logitech Z205 ] on usb-0000:00:1d.1-1/input2 updated to reflect the fact that this was Xubuntu desktop (from Kubuntu install originally) where I had this problem. I was able to easily do this from Ubuntu Natty installation.

  Read the article

• PowerPivot: editing measures when you reach 45

  - by AlbertoFerrari

  I have always been used to small fonts but now, as I am getting older, I’d better admit that a greater font is much more relaxing. Editing PowerPivot measures has always been a pain, since all you have available is a small text box and I hate to admit that I got used to leverage ZoomIt for a long time to edit measures. Today I ran into a great Windows feature that I did not know about: ctrl-wheel on the mouse inside a textbox increases the font size of the text box. It seems to work with most textboxes...(read more)

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >