Search Results

Search found 22298 results on 892 pages for 'default'.

Page 250/892 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• IE 8 crashes when opening an html file from an autorun CD

  - by dave4351

  On Windows 7, when I insert a CD with a very simple HTML page referenced in the autorun.inf file, Internet Explorer 8 opens and then immediately crashes, with the error message "Internet Explorer has stopped working" and then checks for a solution. Then it says "A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available." On Windows Vista, IE 8 just opens and then closes silently, with no error messages or help of any kind. I have since discovered this is due to IE 8's "protected mode" and turning this off fixes the issue so that the HTML file on the CD launches normally. What I'd like to know: is there any way to get around this, so that I can launch a simple HTML file in the user's default browser, using an autorun.inf file on a CD, without first having my users open IE 8 and turn off protected mode? Perhaps the most bizarre thing is that if IE is already open when you insert the CD, the HTML page just opens--no crash. It only crashes if IE 8 happens to be closed when you insert the CD. And so a possible workaround may be to get the default browser to launch and then open the HTML file. All suggestions welcome.

  Read the article

• Is there any limit to AIX 5.3 pipe size ?

  - by snowflake

  Hello, I'm in trouble while performing cat/tail/head operation on large files on Aix 5.3. When asking for a cat of several 1Go file redirected to another one: cat file1 file2 file3 > outputfile The outputfile is limited to 2Go (cat: output error and result file is 2147483647 bytes) Filesystem is jfs2. I successfully uploaded through ftp 10Go files on the filesystem without problem. I found nothing relevant in etc/security/limits: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a core file size (blocks) unlimited data seg size (kbytes) 245759 file size (blocks) unlimited max memory size (kbytes) unlimited open files 2000 pipe size (512 bytes) 64 stack size (kbytes) 32768 cpu time (seconds) unlimited max user processes 2048 virtual memory (kbytes) 278527 The problem does not occur on another AIX 5.3 server, I'm just looking for a different configuration that might be the source of the problem. /etc/security/limits on the server without the problem: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a on the server without the problem: core file size (blocks, -c) 1048575 data seg size (kbytes, -d) 131072 file size (blocks, -f) unlimited max memory size (kbytes, -m) 32768 open files (-n) 20000 pipe size (512 bytes, -p) 64 stack size (kbytes, -s) 32768 cpu time (seconds, -t) unlimited max user processes (-u) 262144 virtual memory (kbytes, -v) unlimited

  Read the article

• Error in Bind9 named.conf file. Bind won't start.

  - by tj111

  I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

  Read the article

• MySQL Cluster ndb_mgmd error

  - by Patryk

  I set up MySQL Cluster on Ubuntu. My ndb_mgmd.cnf file looked: [NDBD DEFAULT] NoOfReplicas=2 DataDir= /var/lib/mysql-cluster # Management Node [NDB_MGMD] NodeId=1 HostName=192.168.204.20 DataDir=/var/lib/mysql-cluster # Storage Nodes (one for each node) [NDBD] NodeId=2 HostName=192.168.204.25 DataDir=/var/lib/mysql-cluster [NDBD] NodeId=3 HostName=192.168.204.26 DataDir=/var/lib/mysql-cluster # SQL Nodes (one for each node) [MYSQLD] NodeId=4 HostName=192.168.204.30 Now I want to edit this configuration, so I changed this file: [NDBD DEFAULT] NoOfReplicas=2 DataDir= /var/lib/mysql-cluster # Management Node [NDB_MGMD] NodeId=1 HostName=192.168.204.20 DataDir=/var/lib/mysql-cluster # Storage Nodes (one for each node) [NDBD] NodeId=2 HostName=192.168.204.25 DataDir=/var/lib/mysql-cluster [NDBD] NodeId=3 HostName=192.168.204.26 DataDir=/var/lib/mysql-cluster # SQL Nodes (one for each node) [MYSQLD] NodeId=4 HostName=192.168.204.25 [MYSQLD] NodeId=5 HostName=192.168.204.26 But ndb_mgm > show; still shows: Connected to Management Server at: localhost:1186 Cluster Configuration --------------------- [ndbd(NDB)] 2 node(s) id=2 (not connected, accepting connect from 192.168.204.25) id=3 (not connected, accepting connect from 192.168.204.26) [ndb_mgmd(MGM)] 1 node(s) id=1 @192.168.204.20 (mysql-5.1.51 ndb-7.1.9) [mysqld(API)] 1 node(s) id=4 (not connected, accepting connect from 192.168.204.30) I tried: sudo /etc/init.d/mysql-ndb-mgm restart sudo ndb_mgmd --initial sudo ndb_mgmd -f /etc/mysql/ndb_mgmd.cnf And nothing works. Any help?

  Read the article

• Spotlight actually searching every file on "This Mac"

  - by Cawas

  I know of 2 ways to search for any file in your machine using Finder (some say it's Spotlight) and no Terminal. To prevent answers / comments about Terminal, I consider it either for scripting something or as last resource. It's not practical for lots of usages. For instance, if you want to find something to attach to a mail, or embed in iTunes or any other app, you can just drag n' drop one or many of them. Definitely not practical to do under Terminal. There are many cases of use for any, but the focus here is Graphical User Interface. Well, the 2 ways basically are: Press Cmd + Opt + Spacebar and type in your search. Press the + button, select "System files" and "are included". This is so far my preferred way, but I'm not sure it will go through every file. Open Finder, press Cmd + Shift + G and/or select just one folder. Type in your search and select the folder rather than "This Mac". This will bring files not shown in "This Mac" if you select a folder outside of the default scope. Thing is, none of those is really convenient or have the nice presentation from regular Spotlight, which you get from Cmd + Spacebar and just typing. And, as far as I've heard, the default behavior on Spotlight in Tiger was actually being able to find files anywhere. So, is there any way to make the process significantly simpler? Maybe some tweak, configuration or really good Spotlight alternative? I'd rather keep it simple and tweak Spotlight.

  Read the article

• Internet doesn't work when enable local network

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: Lan A) WAN interface (192.168.51.50) ( Used for internet) Lan B) LAN interface (192.168.30.228) ( used for local connectivity ) When I keep both LAN Enabled than my internet doesn't work, but if I disable my local LAN then internet works fine. How can I resolve this issue? Do I need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Cisco IOS policy route for router originated VPN traffic

  - by Paul

  We have a Cisco IOS router with two DSL connections. One of them is intended for general traffic (ADSL), the other for VPN links (BDSL) and various other traffic. So the default route is the ADSL link, and we have a combination of static routes for the VPN traffic, and policy routes for other traffic types that should go out the BDSL link. For site to site traffic, this is fine, we just static route the public IPs and remote networks out of the BDSL line. The policy based routing works fine for any internal traffic that matches an ACL. The problem is now that there are remote VPN sites originating from dynamic addresses, so we cannot use static routes. The replies to incoming ISAKMP requests are following the default route out of the ADSL (despite there being no crypto map on that interface). I want to route the outgoing VPN traffic out of the BDSL. I have tried adding udp/500 and esp to and from the route-map acl that pushes traffic out of the BDSL line, but it doesn't match, presumably because the route-map happen earlier than the IPSec stuff. Any ideas how I can do this? IOS ver: 12.4.13T.

  Read the article

• Hylafax: Encounter "No font metric information" when try to send a fax

  - by Chau Chee Yang

  I am using Hylafax 6.0.5 on Fedora 13 x86_64. As there are no rpm package available for Fedora 13, I use the source tar ball to install hylafax myself. Everything seems fine during compile and install. I try to send a fax with sendfax and encounter error: # sendfax -n -d <fax-number> /etc/passwd /usr/local/sbin/textfmt: No font metric information found for "Courier-Bold". Usage: /usr/local/sbin/textfmt [-1] [-2] [-B] [-c] [-D] [-f fontname] [-F fontdir(s)] [-m N] [-o #] [-p #] [-r] [-U] [-Ml=#,r=#,t=#,b=#] [-V #] files... >out.ps Default options: -f Courier -1 -p 11bp -o 0 Error converting document; command was "/usr/local/sbin/textfmt -B -f Courier-Bold -Ml=0.4in -p 11 -s default >'/tmp//sndfaxp5GdJ9' <'/etc/passwd'" It seems like there is problem with font problem. I have ghostscript-fonts installed too. I can't find hyla.conf in path /etc/hylafax. There is no /etc/hylafax path in my file system. All configuration files seems located in /var/spool/hylafax/etc. Please advice. Thank you.

  Read the article

• Driver issue for 7850 HD Diamond Windows 7

  - by Mr.Student

  I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

  Read the article

• Outlook 2007, how to stop replies from being sent if they meet criteria

  - by CChriss

  I have my college's email account auto-forwarded (they don't offer pop3 or imap) to my main gmail account so I don't have to go to their website to check for mail. That gmail account, and others, use pop3 down to my Outlook 2007. In my Outlook, I have a rule that puts mail sent to my @college address into a folder named Collegemail. Since the college email system lacks pop3 or imap, I have to go to their site to send a reply, so that the reply will be sent from my @college email address. The problem is that I cannot seem to get into the habit of going to my college's website to reply to those emails, so quite often I reply to them while in Outlook, which means my replies are sent "from" my main gmail address. How can I set up Outlook to either 1) disable replying to emails in the Collegemail folder or to emails where my college email address is in the original To: line, or else 2) set it to send those replies from a non-functional dummy account. The dummy account would be unable to send the email so the email would be stuck in the Outbox. (I already have the non-functional dummy account set up as Outlook's "Default" account. When I compose a new mail I have to deliberately pick one of my good accounts to send the new mail with, or else Outlook uses the default dummy account and the email stays in the Outbox with a Send error.) Thanks. Update: Anybody? Please help.

  Read the article

• Win 2008 R2 terminal server and redirected printer queue security

  - by Ian

  I have a case where I need a non-priv account to be able to make a modification to the redirected printer. I know, its not advisable but we're not giving them access - changes will be made in code. So, following the docs (http://technet.microsoft.com/en-us/library/ee524015(WS.10).aspx) I modified the default security for new printer queues. This doesnt work though as windows doesn't seem to assign the privs you configure in the printer admin tool to redirected printer queues. As I test I added a non-priv test user to the default security tab in the printer admin tool (control panel - admin tools - printer admin. I assigned it all privs (its a test) and logged the user into the terminal server. The redirected printers duely appeared as usual. However if I open the printer properties - security tab, the user appears in the list of accounts/groups but the options I selected (all privs) are not set. Instead the user special privs box is marked and when I click on 'advanced options' and view them, there is nothing marked. So, something is clearing these options.... the question is, why and how can I convince it not to? Ian

  Read the article

• tftpd-hpa service must be restarted before working after fresh boot

  - by Steve

  I'm running Ubuntu 12.04 inside a VirtualBox VM. I've installed tftpd-hpa so I can boot an embedded Linux device via tftp. My problem is that after a fresh boot of the VM, tftpd doesn't seem to work until I restart the service, after which is works great until the system is rebooted. The transcript below should explain the situation. EDIT: After the fresh boot, I execute netstat -a | grep tftp and find nothing. After restarting the service, the same command returns udp 0 0 *:tftp *:* (whitespace removed). I think this might be the key to the problem, I'm just not sure how to resolve it. I don't think it's related to this specific issue, but I had another problem with tftpd that was asked and answered in this question. steve@steve-VirtualBox:~$ cat /etc/default/tftpd-hpa # /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/var/lib/tftpboot" TFTP_ADDRESS="0.0.0.0:69" TFTP_OPTIONS="--secure" steve@steve-VirtualBox:~$ ls -l /var/lib/tftpboot total 8204 -rw-r--r-- 1 root root 34352 May 28 08:22 am335x-boneblack.dtb -rw-r--r-- 1 root root 33206 May 28 08:22 am335x-bone.dtb -rw-r--r-- 1 root root 41564 May 28 08:22 am335x-evm.dtb -rw-r--r-- 1 root root 38048 May 28 08:22 am335x-evmsk.dtb -rwxr-xr-x 1 root root 4117904 May 20 09:39 zImage -rw-r--r-- 1 root root 4117616 May 28 08:22 zImage-am335x-evm.bin steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Transfer timed out. tftp> quit steve@steve-VirtualBox:~$ sudo service tftpd-hpa restart [sudo] password for steve: tftpd-hpa stop/waiting tftpd-hpa start/running, process 2106 steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Received 4143798 bytes in 1.4 seconds tftp> quit steve@steve-VirtualBox:~$

  Read the article

• Centos 6.2 Fresh 'Basic Server' install networking issues

  - by RWC

  I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

  Read the article

• Can I setup NAT for the same service, two public IPs on different routers to the same private IP?

  - by James

  This might be needlessly complex, but here goes. I've got two Firebox x550e devices. The first has a local IP of 10.0.0.1, public IP 64.x.x.x. The second has a local IP of 10.0.0.10, public IP 70.x.x.x. There is an FTP server on our LAN with a private IP of 10.0.0.55. I've set up NAT rules in each of the Fireboxes, on the first firebox it is 64.x.x.x-10.0.0.55 tcp 21, on the second 70.x.x.x-10.0.0.55 tcp 21. The first rule works fine. I can ftp to 64.x.x.x and everything's good. The second rule doesn't work. ftp to 70.x.x.x results in a connection timeout. The second firebox logs say the connection is being allowed through. The default gateway on the FTP server is 10.0.0.1 (the first firebox) If I change the default gateway on the server to 10.0.0.10, the rule on the second firebox starts working, but the rule from the first firebox stops. Is there some way to make this work for both rules?

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• MySQL encoding problem after site move

  - by Quan Zhou

  Guys, I need your help. Since last month my friend has lost his database on Dreamhost, he decided to move his wordpress based blog site (written in Chinese) to my server. He's using a wp-plugin called wp-db-backup to perform regular db backups. And the servers backgrounds are: Dreamhost: Linux 2.6.31.5-modsign-aufs2-grsec-2-opt mysql Ver 14.12 Distrib 5.0.16, for pc-linux-gnu (i386) using readline 5.0 apache2 unknown version My Server: Linux li159-46 2.6.32.12-x86_64-linode12 mysql Ver 14.14 Distrib 5.1.45, for debian-linux-gnu (x86_64) using readline 6.1 nginx 0.8.36 His site's encoding was UTF-8 in both wp-config and db. I imported his db backup file in UTF-8 by default, then I sync'd files using rsync from dreamhost, then I just changed the db address and nothing more. But when I take first look at the "new" site, it was full of unreadable characters, I met this problem before, I changed charset options in browser but none of them can make it displayed properly. Then I converted his db to GB18030, it works with only if browser set charset to GB18030 either GBK, but by default they recognize the charset as UTF-8. I tried to edit the headers but it doesn't work. What could I do now? Thx~~

  Read the article

• Emails sent through SMTP on VPS are considered to be spam

  - by Ilya

  During our business we have to make regular mailing to our clients: invoices, information emails, etc. Previously we received and sent emails using mail server of our hosting provider. But as the number of clients increased, we have to order VPS and install our own SMTP server their for performing our mailings. So, now we have default provider mail server for receiving emails, let it be business.com. We have email accounts like [email protected], etc. We use this mail server to receive emails and manage our email accounts. And we have SMTP server which is running on VPS. We use this SMTP only for sending emails with From addresses like [email protected]. VPS has default DNS records created by provider, let it be IP.AD.RE.SS <- ip-ad-re-ss.provider.com. Mailings are made using either desktop email clients or custom Java-based application which uses JavaMail for sending emails. The problem is that most of emails sent by us are placed in spam folders in clients email accounts. Clients have their email in Gmail, Yahoo, Hotmail, etc. Could you please tell what is the most probable reason and solution of described problem? Are there any service in Intranet where we can send test email and get an answer with description why this email could be considered to be spam?

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Routing for Two Hosts Behind a IPSec Tunnel

  - by Brent

  Network A 10.110.15.0/24 Firewall is .1 Host A is .2 Network B 10.110.16.0/24 Firewall is .1 Host B is .2 Two Cisco ASA's. IPSec tunnel with a crypo map that secures 10.110.15.0/24 <- 10.110.16.0/24. Let's say two hosts, 10.110.15.2 and 10.110.16.2 need to talk to each other. Normally I have to enter a persistent static route on a each host along the lines of: route add 10.110.16.0 mask 255.255.255.0 10.110.15.1 metric 1 -p (on the "A" box) I also have to enter another persistent static route on the .16 host in order for the traffic to know how to get back to the .15 network. Note that the default for each machine IS the firewall, so .1. I have no problem adding persistent routes on Windows/ESX/*nux machines but what about a smart switch in the .16 network that I want to manage from the .15 network. Do I need to run a routing protocol? Do I need to have Reverse Route Injection enabled on both ends of the IPSec tunnel? Should I add a route on the firewall? If so, how do you formulate it? Does it get a metric of 1 and my default route 0.0.0.0 get a metric of 2?

  Read the article

• How Do I Install Latest Java Plugin on Ubuntu 8.04 LTS with Custom Firefox 3.6.3?

  - by Volomike

  I have Ubuntu 8.04 LTS and will need to remain on that for awhile as I am a programmer and cannot disturb what I'm doing in the middle of a project. As you know, it doesn't want to install the latest Firefox by default and keeps me in the stone age. So, I had to install my own Firefox. I did so and with relative ease I was able to install the Flash plugin using the normal 'ln -s' technique one usually does with /usr/lib/firefox/plugins. Now I need to do a Gotomypc.com task and it requires Java -- moan -- so I need to figure out how to install Java. I downloaded and installed the latest Java plugin in /usr/java, and I do see underneath that layer of folders a plugins folder with a .so file. So, I went to /usr/lib/firefox/plugins and did this: ln -s /usr/java/jre1.6.0_20/plugin/i386/ns7/libjavaplugin_oji.so Then, I also read on the web that one has to create a ~/.mozilla/plugins folder, cd into it, and then run the same ln -s command again. Another site recommended finding one's ~/.mozilla/firefox and renaming it to ~/.mozilla/firefox.old (after you backed up your bookmarks) and then launching firefox again so that it creates ~/.mozilla/firefox and uses the new Java plugin. Well, all these attempts have completely failed and it is incredibly frustrating. I do about:plugins to see my plugins and all I get are the Flash and the default null plugin. I do not see the Java one. Also, they said on my tools menu with Firefox 3.6.3 I would see a Java Console menu and I don't see that either. I found a pluginreg.dat somewhere deep under ~/.mozilla/firefox, but it does not list the Java plugin inside -- only Flash and the null plugin. Please help me install Java. I need to help a client out and need to connect to his PC remotely with gotomypc, which requires Java inside firefox.

  Read the article

• really weird DNS problem in Ubuntu {after one month, seems like ISP problem}

  - by OmniWired

  Hello everyone. I been having this random dns problem, in Ubuntu 10.04 and in 10.10 it started about 2 weeks ago after (I believe) an update. Basically when I go to a website randomly I get that the website I'm visiting is not available ("Oops! Google Chrome could not connect to ..." & "This webpage is not available."). I tested with Chromium "7.0.515.0 (58587)" and Firefox minefield (4.0ish) and 3.6.9. I did these 4 things already: /etc/default/grub GRUB_CMDLINE_LINUX="ipv6.disable=1" and this: /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 *disabling Chromium DNS pre-fetching *using Google and OpenDNS servers as well as ISP DNS servers. But didn't improve, also no other computers in my network have the same problem. All computer wired to the same router. I'm a software engineer that run out of ideas, please help me. Thanks in advance. UPDATE: some programs (synaptic / firefox update/ vuze(azureus)) say connection refused for the error. Most of the time a second try will fix the "refusal". UPDATE2: I found out with Wireshark, that everytime I have this problem i've got this 192.168.0.10 8.8.8.8 ICMP Destination unreachable (Port unreachable) Confirmed an ISP error. ISP;Speedy Location: Argentina, Buenos Aires (capital Federal) Area.

  Read the article

• Installing/enabling PHP Pecl Intl extension on CentOs 5

  - by Marijn Huizendveld

  Original question: I'm having trouble installing the PHP Pecl Intl extension on my CentOs 5 machine. After installing both icu and libicu with the following commands: $ yum install icu $ yum install libicu I tried to install the Intl extension like so: $ /usr/bin/pecl install intl I selected to search for the default location for the ICU libraries and header files. It ends up crashing like this: checking whether to enable internationalization support... yes, shared checking for icu-config... no checking for location of ICU headers and libraries... not found configure: error: Unable to detect ICU prefix or no failed. Please verify ICU install prefix and make sure icu-config works. ERROR: `/tmp/pear/temp/intl/configure --with-icu-dir=DEFAULT' failed update After successfully installing the development version of icu as suggested by RusAlex (thanks RusAlex) like so: $ yum install libicu-devel I ran into a new problem which I also encountered locally the following command: $ /usr/bin/pecl install intl now produces this error: /private/tmp/pear/temp/intl/collator/collator_class.c:92: error: duplicate 'static' /private/tmp/pear/temp/intl/collator/collator_class.c:96: error: duplicate 'static' /private/tmp/pear/temp/intl/collator/collator_class.c:101: error: duplicate 'static' /private/tmp/pear/temp/intl/collator/collator_class.c:107: error: duplicate 'static' make: *** [collator/collator_class.lo] Error 1 ERROR: `make' failed It appears to have something to do with PHP 5.3 being bundled with Intl already. But how can I enable this extension, if I look in my PHP Info than I cannot find any reference to it...

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• Use Alladin eToken with ThunderBird and other tool

  - by Yurij73

  I'm looking for an example on how to setup the eToken PRO Java device to work with Mozilla Thunderbird and with other Linux tool such as PAM logon. I installed distributed pkiclient-5.00.28-0.i386.RPM from the official product page eToken Pro but that tool only handles importing/exporting certificates on the device. I read a glance an old HOWTO from eToken on Linux, but I couldn't install pkcs11-lib for this device as recommended for Thunderbird use this crypto device. It seems my usb token isn't listed in system, unless lsusb show it, so that is the matter modutil -list -dbdir /etc/pki/nssdb Listing of PKCS #11 Modules NSS Internal PKCS #11 Module Blockquote slots: 2 slots attached Blockquote status: loaded Blockquote slot: NSS User Private Key and Certificate Services Blockquote token: NSS Certificate DB Blockquote CoolKey PKCS #11 Module Blockquote library name: libcoolkeypk11.so Blockquote slots: 1 slot attached Blockquote status: loaded Blockquote slot: AKS ifdh [Main Interface] 00 00 token: is my token absent? on other hand i don't know which module is convenient to Java Pro, does CoolKey does all the job well? It seems Java token is too new hardware for Linux? there is excerpt from /etc/pam_pkcs11.conf #filename of the PKCS #11 module. The default value is "default" use_pkcs11_module = coolkey; screen_savers = gnome-screensaver,xscreensaver,kscreensaver pkcs11_module coolkey { module = libcoolkeypk11.so; description = "Cool Key"`

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >