Search Results

Search found 6697 results on 268 pages for 'e learning'.

Page 250/268 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• Speed Problem with Wireless Connectivity on Cisco 877w

  - by Carl Crawley

  Having a bit of a weird one with my local LAN setup. I recently installed a Cisco 877W router on my DSL2+ connection and all is working really well.. Upgraded the IOS to 12.4 and my wired clients are streaming connectivity superfast at 1.3mb/s. However, there seems to be an issue with my wireless clients - I can't seem to stream any data across the local wireless connection (LAN) and using the Internet, whilst responsive enough isn't really comparable with the wired connection speed. For example, all devices are connected to an 8 Port Gb switch on FE0 from the Router with a NAS disk and on my wired clients, I can transfer/stream etc absolutely fine - however, transferring a local 700Mb file on my local LAN estimates 7-8 hours to transfer :( The Wireless config is as follows : interface Dot11Radio0 description WIRELESS INTERFACE no ip address ! encryption mode ciphers tkip ! ssid [MySSID] ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 channel 2462 station-role root rts threshold 2312 world-mode dot11d country GB indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding All devices are connected to the Gb Switch which is connected to FE0 with the following: Hardware is Fast Ethernet, address is 0021.a03e.6519 (bia 0021.a03e.6519) Description: Uplink to Switch MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 19 packets/sec 5 minute output rate 167000 bits/sec, 23 packets/sec 177365 packets input, 52089562 bytes, 0 no buffer Received 919 broadcasts, 0 runts, 0 giants, 0 throttles 260 input errors, 260 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 156673 packets output, 106218222 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Not sure why I'm having problems on the wireless and I've reached the end of my Cisco knowledge... Thanks for any pointers! Carl

  Read the article

• Marshalling polymorphic objects in JAX-WS

  - by pkchukiss

  I'm creating a JAX-WS type webservice, with operations that return an object WebServiceReply. The class WebServiceReply itself contains a field of type Object. The individual operations would populate that field with a few different data-types, depending on the operation. Publishing the WSDL (I'm using Netbeans 6.7), and getting a ASP.NET application to retrieve and parse the WSDL was fine, but when I tried to call an operation, I would receive the following exception: javax.xml.ws.WebServiceException: javax.xml.bind.MarshalException - with linked exception: [javax.xml.bind.JAXBException: class [LDataObject.Patient; nor any of its super class is known to this context.] How do I mark the annotations in the DataObject.Patient class, as well as the WebServiceReply class to get it to work? I haven't been able to fine a definitive resource on marshalling based upon annotations within the target classes either, so it would be great if anybody could point me to that too. WebServiceReply.java @XmlRootElement(name="WebServiceReply") public class WebServiceReply { private Object returnedObject; private String returnedType; private String message; private String errorMessage; .......... // Getters and setters follow } DataObject.Patient.java @XmlRootElement(name="Patient") public class Patient { private int uid; private Date versionDateTime; private String name; private String identityNumber; private List<Address> addressList; private List<ContactNumber> contactNumberList; private List<Appointment> appointmentList; private List<Case> caseList; } Solution (Thanks to Gregory Mostizky for his answer) I edited the WebServiceReply class so that all the possible return objects extend from a new class ReturnValueBase, and added the annotations using @XmlSeeAlso to ReturnValueBase. JAXB worked properly after that! Nonetheless, I'm still learning about JAXB marshalling in JAX-WS, so it would be great if anyone can still post any tutorial on this. Gregory: you might want to add-on to your answer that the return objects need to sub-class from ReturnValueBase. Thanks a lot for your help! I had been going bonkers over this problem for so long!

  Read the article

• Auto update the content in ASP.NET

  - by Zerotoinfinite

  I have to design a website where user can update their status, just like facebook and twitter and other social networking sites. Now my requirement is to refresh the feed with new user updates. Ex: when the new status comes facebook automatically add that on the top of the feed. on the other hand twitter shows the number of updates which is ready to be load. both ways are acceptable to me Now, I have to decide what is the best way to achieve this functionality. I am open to use ASP.NET. So I am confused that regular repeater control with timer and auto refresh or any other way? (I am wondering that if I set repeater for auto update and meanwhile if user is performing some action on any status it will lost). or do I need to change my framework from ASP.NET to ASP.NET MVC (I am little afraid with MVC as I have very less knowledge regarding it and I know it has a learning curve to master ajax/Jquery things) Any suggestion how I can I achieve it in a better and feasible way? EDIT1 I am not looking for a code but I want advice to achieve this. Supporting URL's would be appreciated. EDIT2 I am open to JQuery which can regularly check the database and fill the section. But my concern is this that if user is updating any comment and want to load/feed is automatically generated. his textbox text shouldn't be disappear (just like facebook, twitter or Linkedin) EDIT3 I have seen that on Stack overflow when any other user has modified the question/answer, I got notification like this question/answer is modified. and when I clicked on that notification only that section got reloaded. I am curious to know how to achieve this functionality. So that when user is commenting on a status/post and if meanwhile someone has updated the content then it would show the other user comment. Edit4 Could someone please recommend me an example of ASP.NET MVC 3+ which can do similar kind of activity (i.e. one input box and once user insert an text it will add the item in the list (with JQuery).

  Read the article

• objective-c default init method for class?

  - by Alex

  Hello, I have two differing methods for initializing my objective-c class. One is the default, and one takes a configuration parameter. Now, I'm pretty green when it comes to objective-c, but I've implemented these methods and I'm wondering if there's a better (more correct/in good style) way to handle initialization than the way I have done it. Meaning, did I write these initialization functions in accordance with standards and good style? It just doesn't feel right to check for the existence of selfPtr and then return based on that. Below are my class header and implementation files. Also, if you spot anything else that is wrong or evil, please let me know. I am a C++/Javascript developer who is learning objective-c as hobby and would appreciate any tips that you could offer. #import <Cocoa/Cocoa.h> // class for raising events and parsing returned directives @interface awesome : NSObject { // silence is golden. Actually properties are golden. Hence this emptiness. } // properties @property (retain) SBJsonParser* parser; @property (retain) NSString* eventDomain; @property (retain) NSString* appid // constructors -(id) init; -(id) initWithAppId:(id) input; // destructor -(void) dealloc; @end #import "awesome.h" #import "JSON.h" @implementation awesome - (id) init { if (self = [super init]) { // if init is called directly, just pass nil to AppId contructor variant id selfPtr = [self initWithAppId:nil]; } if (selfPtr) { return selfPtr; } else { return self; } } - (id) initWithAppId:(id) input { if (self = [super init]) { if (input = nil) { input = [[NSString alloc] initWithString:@"a369x123"]; } [self setAppid:input]; [self setEventDomain:[[NSString alloc] initWithString:@"desktop"]]; } return self; } // property synthesis @synthesize parser; @synthesize appid; @synthesize eventDomain; // destructor - (void) dealloc { self.parser = nil; self.appid = nil; self.eventDomain = nil; [super dealloc]; } @end Thanks!

  Read the article

• How can I use this downloaded Class(es) on my Prototype Routine?

  - by O.C.

  I'm a newbie and I'm in need of some help. I'm working on a prototype for an app, but I'm learning at the same time. I want to display a popup image over a given UIView, but I would like it to behave like the UIAlertView or like the Facebook Connect for iPhone modal popup window, in that it has a bouncy, rubbber-band-like animation to it. I was able to find the following class(es) on the net, from someone who was trying to do something similar. He/she put this together, but there was no Demo, no instructions nor a way to contact them. Being that I am so new, I don't have any idea as to how to incorporate this into my code. This is the routine where I need the bouncy image to appear... //======================================================== // // productDetail // - (void) showProductDetail { _productDetailIndex++; if (_productDetailIndex > 7) { return; } else if (_productDetailIndex == 1) { NSString* filename = [NSString stringWithFormat:@"images/ICS_CatalogApp_0%d_ProductDetailPopup.png", _productDetailIndex]; [_productDetail setImageWithName:filename]; _productDetail.transform = CGAffineTransformMakeScale(0.1,0.1); [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:0.5]; // other animations goes here _productDetail.transform = CGAffineTransformMakeScale(1,1); // other animations goes here [UIView commitAnimations]; } NSString* filename = [NSString stringWithFormat:@"images/ICS_CatalogApp_0%d_ProductDetailPopup.png", _productDetailIndex]; [_productDetail setImageWithName:filename]; _productDetail.x = (self.width - _productDetail.width); _productDetail.y = (self.height - _productDetail.height); } and here is the code I found... float pulsesteps[3] = { 0.2, 1/15., 1/7.5 }; - (void) pulse { self.transform = CGAffineTransformMakeScale(0.6, 0.6); [UIView beginAnimations:nil context:nil]; [UIView setAnimationDuration:pulsesteps[0]]; [UIView setAnimationDelegate:self]; [UIView setAnimationDidStopSelector:@selector(pulseGrowAnimationDidStop:finished:context:)]; self.transform = CGAffineTransformMakeScale(1.1, 1.1); [UIView commitAnimations]; } - (void)pulseGrowAnimationDidStop:(NSString *)animationID finished:(NSNumber *)finished context:(void *)context { [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:pulsesteps[1]]; [UIView setAnimationDelegate:self]; [UIView setAnimationDidStopSelector:@selector(pulseShrinkAnimationDidStop:finished:context:)]; self.transform = CGAffineTransformMakeScale(0.9, 0.9); [UIView commitAnimations]; } - (void)pulseShrinkAnimationDidStop:(NSString *)animationID finished:(NSNumber *)finished context:(void *)context { [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:pulsesteps[2]]; self.transform = CGAffineTransformIdentity; [UIView commitAnimations]; } My routine is based on the Prototyping class given by Apple during WWDC 09. It may not be "correct" but it works as is. I just would like to add the animation to this image/screen to really make the concept clear.

  Read the article

• PERL newbie : get a proper minimal debug_mode solution

  - by Michael Mao

  Hi all: I am learning PERL in a "head-first" manner. I am absolutely a newbie in this language: I am trying to have a debug_mode switch from CLI which can be used to control how my script works, by switching certain subroutines "on and off". And below is what I've got so far: #!/usr/bin/perl -s -w # purpose : make subroutine execution optional, # which is depending on a CLI switch flag use strict; use warnings; use constant DEBUG_VERBOSE => "v"; use constant DEBUG_SUPPRESS_ERROR_MSGS => "s"; use constant DEBUG_IGNORE_VALIDATION => "i"; use constant DEBUG_SETPPING_COMPUTATION => "c"; our ($debug_mode); mainMethod(); sub mainMethod # () { if(!$debug_mode) { print "debug_mode is OFF\n"; } elsif($debug_mode) { print "debug_mode is ON\n"; } else { print "OMG!\n"; exit -1; } checkArgv(); printErrorMsg("Error_Code_123", "Parsing Error at..."); verbose(); } sub checkArgv #() { print ("Number of ARGV : ".(1 + $#ARGV)."\n"); } sub printErrorMsg # ($error_code, $error_msg, ..) { if(defined($debug_mode) && !($debug_mode =~ DEBUG_SUPPRESS_ERROR_MSGS)) { print "You can only see me if -debug_mode is NOT set". " to DEBUG_SUPPRESS_ERROR_MSGS\n"; die("terminated prematurely...\n") and exit -1; } } sub verbose # () { if(defined($debug_mode) && ($debug_mode =~ DEBUG_VERBOSE)) { print "Blah blah blah...\n"; } } So far as I can tell, at least it works...: the -debug_mode switch doesn't interfere with normal ARGV the following commandlines work: ./optional.pl ./optional.pl -debug_mode ./optional.pl -debug_mode=v ./optional.pl -debug_mode=s However, I am puzzled when multiple debug_modes are "mixed", such as: ./optional.pl -debug_mode=sv ./optional.pl -debug_mode=vs I don't understand why the above lines of code "magically works". I see both of the "DEBUG_VERBOS" and "DEBUG_SUPPRESS_ERROR_MSGS" apply to the script, which is fine in this case. However, if there are some "conflicting" debug modes, I am not sure how to set the "precedence of debue_modes"? Also, I am not certain if my approach is good enough to Perlists and I hope I am getting my feet in the right direction. One biggest problem is that I now put if statements inside most of my subroutines for controlling their behavior under different modes. Is this okay? Is there a more elegant way? I know there must be a debug module from CPAN or elsewhere, but I wanna a real minimal solution that doesn't depend on any other module than the "default" And I cannot have any control on the environment where this script will be executed... Many thanks to the suggestions in advance.

  Read the article

• Can't use attached property on combobox inside hierarchical datatemplate WPF

  - by jesse_t_r

  I'm hoping to use an attached property to assign a command to the selection changed event of a combobox that is embedded inside a treeview. I'm attempting to set the attached property inside the hierchical data template for the tree but the command is not set and does not fire when the item in the combobox is changed. I've found that setting the attached property directly on a combobox outside of a datatemplate works fine; here is how I'm trying to set the property in the template: <HierarchicalDataTemplate x:Key="template1" ItemsSource="{Binding Path=ChildColumns}"> <Border Background="{StaticResource TreeItem_Background}" BorderBrush="Blue" BorderThickness="2" CornerRadius="5" Margin="2,5,5,2" HorizontalAlignment="Left" > <Grid> <Grid.ColumnDefinitions > <ColumnDefinition Width="Auto"/> <ColumnDefinition Width="*"/> <ColumnDefinition Width="*"/> </Grid.ColumnDefinitions> <Grid.RowDefinitions> <RowDefinition /> <RowDefinition /> </Grid.RowDefinitions> <TextBlock MinWidth="80" HorizontalAlignment="Left" Grid.Column="0" Margin="5,2,2,2" Grid.Row ="0" Text="{Binding Path=ColName}"/> <ComboBox Name="cboColType" Grid.Column="1" HorizontalAlignment="Right" ItemsSource="{Binding Source={StaticResource dataFromEnum}}" SelectedItem="{Binding Path=ColumnType}" Margin="2,2,2,2" local:ItemSelectedBehavior.ItemSelected="{Binding Path=LoadConfigCommand}" /> </Grid> </Border> </HierarchicalDataTemplate> I also tried creating a style <Style x:Key="childItemStyle" TargetType="{x:Type FrameworkElement}"> <Setter Property="local:ItemSelectedBehavior.ItemSelected" Value="{Binding Path=LoadConfigCommand}" /> </Style> and setting the itemcontainerstyle to the style in the hierarchical datatemplate..still no luck .. <HierarchicalDataTemplate> ... <ComboBox Name="cboColType" Grid.Column="1" HorizontalAlignment="Right" ItemsSource="{Binding Source={StaticResource dataFromEnum}}" SelectedItem="{Binding Path=ColumnType}" Margin="2,2,2,2" ItemContainerStyle={StaticeResource childItemStyle}" /> ... </HierarchicalDataTemplate> I'm still learning a lot about WPF so I'm assuming there is something particular about the hierchical datatemplate that is not allowing the attache dproperty to be set..I have found similar posts in the forums and tried to implement their solutions as above, but after a day of searching and experimenting wiht no luck I'm hoping some one has an idea about this...

  Read the article

• Queue ExternalInterface calls to Flash Object in UpdatePanel - Needs Improvement?

  - by Laramie

  A Flash (actually Flex) object is created on an ASP.Net page within an Update Panel using a modified version of the embedCallAC_FL_RunContent.js script so it can be written in dynamically. It is re-created with this script with each partial postback to that panel. There are also other Update Panels on the page. With some postbacks (partial and full), External Interface calls such as $get('FlashObj').ExternalInterfaceFunc('arg1', 0, true); are prepared server-side and added to the page using ScriptManager.RegisterStartupScript. They're embedded in a function and stuffed into Sys.Application's load event, for example Sys.Application.add_load(funcContainingExternalInterfaceCalls). The problem is that because the Flash object's state state may change with each partial postback, the Flash (Flex) object and/or External Interface may not be ready or even exist yet in the DOM when the JavaScript - Flash External Interface call is made. It results in an "Object doesn't support this property or method" exception. I have a working strategy to make the ExternalInterface calls immediately if Flash is ready or else queue them until such time that Flash announces its readiness. //Called when the Flash object is initialized and can accept ExternalInterfaceCalls var flashReady = false; //Called by Flash when object is fully initialized function setFlashReady() { flashReady = true; //Make any queued ExternalInterface calls, then dequeue while (extIntQueue.length > 0) (extIntQueue.shift())(); } var extIntQueue = []; function callExternalInterface(flashObjName, funcName, args) { //reference to the wrapped ExternalInterface Call var wrapped = extWrap(flashObjName, funcName, args); //only procede with ExternalInterface call if the global flashReady variable has been set if (flashReady) { wrapped(); } else { //queue the function so when flashReady() is called next, the function is called and the aruments are passed. extIntQueue.push(wrapped); } } //bundle ExtInt call and hold variables in a closure function extWrap(flashObjName, funcName, args) { //put vars in closure return function() { var funcCall = '$get("' + flashObjName + '").' + funcName; eval(funcCall).apply(this, args); } } I set the flashReady var to dirty whenever I update the Update Panel that contains the Flash (Flex) object. ScriptManager.RegisterClientScriptBlock(parentContainer, parentContainer.GetType(), "flashReady", "flashReady = false;", true); I'm pleased that I got it to work, but it feels like a hack. I am still on the learning curve with respect to concepts like closures why "eval()" is apparently evil, so I'm wondering if I'm violating some best practice or if this code should be improved, if so how? Thanks.

  Read the article

• Explanation of converting exporting an XML document as a relational database using XSLT

  - by Yaaqov

  I would like to better understand the basic steps needed to a take an XML document like this Breakfast Menu... <?xml version="1.0" encoding="ISO-8859-1"?> <breakfast_menu> <food> <name>Belgian Waffles</name> <price>$5.95</price> <description>two of our famous Belgian Waffles with plenty of real maple syrup</description> <calories>650</calories> </food> <food> <name>Strawberry Belgian Waffles</name> <price>$7.95</price> <description>light Belgian waffles covered with strawberries and whipped cream</description> <calories>900</calories> </food> <food> <name>Berry-Berry Belgian Waffles</name> <price>$8.95</price> <description>light Belgian waffles covered with an assortment of fresh berries and whipped cream</description> <calories>900</calories> </food> <food> <name>French Toast</name> <price>$4.50</price> <description>thick slices made from our homemade sourdough bread</description> <calories>600</calories> </food> <food> <name>Homestyle Breakfast</name> <price>$6.95</price> <description>two eggs, bacon or sausage, toast, and our ever-popular hash browns</description> <calories>950</calories> </food> </breakfast_menu> And "export" it to say, an Access or MySQL database using XSLT, creating two joined tables: Table: breakfast_menu Field: menu_item_id Field: food_id Table: food Field: food_id Field: name Field: price Field: description Field: calories If there are online tutorials on this that you know of, I'd be interesting in learning more, as well. Thanks.

  Read the article

• Entering and retrieving data from SQLite for an android List View

  - by Infiniti Fizz

  Hi all, I started learning android development a few weeks ago and have gone through the developer.android.com tutorials etc. But now I have a problem. I'm trying to create an app which tracks the usage of each installed app. Therefore I'm pulling the names of all installed apps using the PackageManager and then trying to put them into an SQLite database table. I am using the Notepad Tutorial SQLite implementation but I'm running into some problems that I have tried for days to solve. I have 2 classes, the DBHelper class and the actual ListActivity class. For some reason the app force closes when I try and run my fillDatabase() function which gets all the app names from the PackageManager and tries to put them into the database: private void fillDatabase() { PackageManager manager = this.getPackageManager(); List<ApplicationInfo> appList = manager.getInstalledApplications(0); for(int i = 0; i < appList.size(); i++) { mDbHelper.addApp(manager.getApplicationLabel(appList.get(i)).toString(), 0); } } addApp() is a function defined in my AppsDbHelper class and looks as follows: public long createApp(String name, int usage) { ContentValues initialValues = new ContentValues(); initialValues.put(KEY_NAME, name); initialValues.put(KEY_USAGE, usage); return mDb.insert(DATABASE_TABLE, null, initialValues); } The database create is defined as follows: private static final String DATABASE_CREATE = "create table notes (_id integer primary key autoincrement, " + "title text not null, usage integer not null);"; I have commented out all statements that follow fillDatabase(); in the onCreate() method of the ListActivity and so know that it is definetely the problem but I don't know why. I am taking the appName and putting it into the KEY_NAME field of the row and putting 0 into the KEY_USAGE field of the row (because initially, my app will default the usage of each app to 0 (not used yet)). If my addApp() function doesn't take the usage and just puts KEY_NAME into the ContentValues and into the database, it seems to work fine, but I want a column for usage. Any ideas why it is not working? Have I overlooked something? Thanks for your time, InfinitiFizz

  Read the article

• MySQL table organization and optimization (Rails)

  - by aguynamedloren

  I've been learning Ruby on Rails over the past few months with no prior programming experience. Lately, I've been thinking about database optimization and table organization. I know there are great books on the subject, but I typically learn by example / as I go. Here's a hypothetical situation: Let's say I am building a social network for a niche community with 250,000 members (users). The users have the ability to attend events. Let's say there are 50,000 past/present/future events. Much like Facebook events, a user can attend any number of events and an event can have any number of attendees. In the database, there would be a table for users and a table for events. Somehow I would have to create an association between the users and events. I could create an "events" column in the users table such that each user row would contain a hash of event IDs, or I could create an "attendees" column in the events table such that each event row would contain a hash of user IDs. Neither of these solutions seem ideal, however. On a users profile page, I want to display the list of events they are associated with, which would require scanning the 50,000 event rows for the user ID of said user if I include an "attendees" column in the events table. Likewise, on an event page, I want to display a list of attendees for the event, which would require scanning the 250,000 user rows for the event ID of said event if I include an "events" column in the users table. Option 3 would be to create a third table that contains the attendee information for each and every event - but I don't see how this would solve any problems. Are these non-issues? Rails makes accessing all of this information easy, but I guess I'm worried about scale. It is entirely possible that I am under-estimating the speed and processing power of modern databases / servers / etc. How long would it take to scan 250,000 user rows for specific event IDs - 10ms? 100ms? 1,000ms? I guess that's not that bad. Am I just over-thinking this?

  Read the article

• Creating a simple templated control. Having issues...

  - by Jimock

  Hi, I'm trying to create a really simple templated control. I've never done it before, but I know a lot of my controls I have created in the past would have greatly benefited if I included templating ability - so I'm learning now. The problem I have is that my template is outputted on the page but my property value is not. So all I get is the static text which I include in my template. I must be doing something correctly because the control doesn't cause any errors, so it knows my public property exists. (e.g. if I try to use Container.ThisDoesntExist it throws an exception). I'd appreciate some help on this. I may be just being a complete muppet and missing something. Online tutorials on simple templated server controls seem few and far between, so if you know of one I'd like to know about it. A cut down version of my code is below. Many Thanks, James Here is my code for the control: [ParseChildren(true)] public class TemplatedControl : Control, INamingContainer { private TemplatedControlContainer theContainer; [TemplateContainer(typeof(TemplatedControlContainer)), PersistenceMode(PersistenceMode.InnerProperty)] public ITemplate ItemTemplate { get; set; } protected override void CreateChildControls() { Controls.Clear(); theContainer = new TemplatedControlContainer("Hello World"); this.ItemTemplate.InstantiateIn(theContainer); Controls.Add(theContainer); } } Here is my code for the container: [ToolboxItem(false)] public class TemplatedControlContainer : Control, INamingContainer { private string myString; public string MyString { get { return myString; } } internal TemplatedControlContainer(string mystr) { this.myString = mystr; } } Here is my mark up: <my:TemplatedControl runat="server"> <ItemTemplate> <div style="background-color: Black; color: White;"> Text Here: <%# Container.MyString %> </div> </ItemTemplate> </my:TemplatedControl>

  Read the article

• Any tool(s) for knowing the layout (segments) of running process in Windows?

  - by claws

  I've always been curious about How exactly the process looks in memory? What are the different segments(parts) in it? How exactly will be the program (on the disk) & process (in the memory) are related? My previous question: http://stackoverflow.com/questions/1966920/more-info-on-memory-layout-of-an-executable-program-process In my quest, I finally found a answer. I found this excellent article that cleared most of my queries: http://www.linuxforums.org/articles/understanding-elf-using-readelf-and-objdump_125.html In the above article, author shows how to get different segments of the process (LINUX) & he compares it with its corresponding ELF file. I'm quoting this section here: Courious to see the real layout of process segment? We can use /proc//maps file to reveal it. is the PID of the process we want to observe. Before we move on, we have a small problem here. Our test program runs so fast that it ends before we can even dump the related /proc entry. I use gdb to solve this. You can use another trick such as inserting sleep() before it calls return(). In a console (or a terminal emulator such as xterm) do: $ gdb test (gdb) b main Breakpoint 1 at 0x8048376 (gdb) r Breakpoint 1, 0x08048376 in main () Hold right here, open another console and find out the PID of program "test". If you want the quick way, type: $ cat /proc/`pgrep test`/maps You will see an output like below (you might get different output): [1] 0039d000-003b2000 r-xp 00000000 16:41 1080084 /lib/ld-2.3.3.so [2] 003b2000-003b3000 r--p 00014000 16:41 1080084 /lib/ld-2.3.3.so [3] 003b3000-003b4000 rw-p 00015000 16:41 1080084 /lib/ld-2.3.3.so [4] 003b6000-004cb000 r-xp 00000000 16:41 1080085 /lib/tls/libc-2.3.3.so [5] 004cb000-004cd000 r--p 00115000 16:41 1080085 /lib/tls/libc-2.3.3.so [6] 004cd000-004cf000 rw-p 00117000 16:41 1080085 /lib/tls/libc-2.3.3.so [7] 004cf000-004d1000 rw-p 004cf000 00:00 0 [8] 08048000-08049000 r-xp 00000000 16:06 66970 /tmp/test [9] 08049000-0804a000 rw-p 00000000 16:06 66970 /tmp/test [10] b7fec000-b7fed000 rw-p b7fec000 00:00 0 [11] bffeb000-c0000000 rw-p bffeb000 00:00 0 [12] ffffe000-fffff000 ---p 00000000 00:00 0 Note: I add number on each line as reference. Back to gdb, type: (gdb) q So, in total, we see 12 segment (also known as Virtual Memory Area--VMA). But I want to know about Windows Process & PE file format. Any tool(s) for getting the layout (segments) of running process in Windows? Any other good resources for learning more on this subject? EDIT: Are there any good articles which shows the mapping between PE file sections & VA segments?

  Read the article

• Running same powershell script multiple asynchronous times with separate runspace

  - by teqnomad

  Hi, I have a powershell script which is called by a batch script which is called by Trap Receiver (which also passes environment variables) (running on windows 2008). The traps are flushed out at times in sets of 2-4 trap events, and the batch script will echo the trap details for each message to a logfile, but the powershell script on the next line of the batch script will only appear to process the first trap message (the powershell script writes to the same logfile). My interpetation is that the defaultrunspace is common to all iterations of the script running and this is why the others appear to be ignored. I've tried adding "-sta" when I invoke the powershell script using "powershell.exe -command", but this didn't help. I've researched and found a method using C# but I don't know this language, and busy enough learning powershell, so hoping to find a more direct solution especially as interleaving a "wrapper" between batch and powershell will involve passing the environment variables. http://www.codeproject.com/KB/threads/AsyncPowerShell.aspx I've hunted through stackoverflow, and again the only question of similar vein was using C#. Any suggestions welcome. Some script background: The powershell script is actually a modification of a great script found at gregorystrike website - cant post the link as I'm limited to one link but its the one for Lefthand arrays. Lots of mods so it can do multiple targets from one .ini file, taking in the environment variables, and options to run portions of the script interactively with winform. But you can see the gist of the original script. The batch script is pretty basic. The keys things are I'm trying to filter out trap noise using the :~ operator, and I tried -sta option to see if this would compartmentalise the powershell script. set debug=off set CMD_LINE_ARGS="%*" set LHIPAddress="%2" set VARBIND8="%8" shift shift shift shift shift shift shift set CHASSIS="%9" echo %DATE% %TIME% "Trap Received: %LHIPAddress% %CHASSIS% %VARBIND8%" >> C:\Logs\trap_out.txt set ACTION="%VARBIND8:~39,18%" echo %DATE% %TIME% "Action substring is %ACTION%" 2>&1 >> C:\Logs\trap_out.txt if %ACTION%=="Remote Copy Volume" ( echo Prepostlefthand_env_v2.9 >> C:\Logs\trap_out.txt c:\Windows\System32\WindowsPowerShell\v1.0\PowerShell.exe -sta -executionpolicy unrestricted -command " & 'C:\Scripts\prepostlefthand_env_v2.9.ps1' Backupsettings.ini ALL" 2>&1 >> C:\Logs\trap_out.txt ) ELSE ( echo %DATE% %TIME% Action substring is %ACTION% so exiting" 2>&1 >> C:\Logs\trap.out.txt ) exit

  Read the article

• How do I add a custom view to iPhone app's UI?

  - by Dr Dork

  I'm diving into iPad development and I'm still learning how everything works together. I understand how to add standard view (i.e. buttons, tableviews, datepicker, etc.) to my UI using both Xcode and Interface Builder, but now I'm trying to add a custom calendar control (TapkuLibrary) to the left window in my UISplitView application. My question is, if I have a custom view (in this case, the TKCalendarMonthView), how do I programmatically add it to one of the views in my UI (in this case, the RootViewController)? Below are some relevant code snippets from my project... RootViewController interface @interface RootViewController : UITableViewController <NSFetchedResultsControllerDelegate> { DetailViewController *detailViewController; NSFetchedResultsController *fetchedResultsController; NSManagedObjectContext *managedObjectContext; } @property (nonatomic, retain) IBOutlet DetailViewController *detailViewController; @property (nonatomic, retain) NSFetchedResultsController *fetchedResultsController; @property (nonatomic, retain) NSManagedObjectContext *managedObjectContext; - (void)insertNewObject:(id)sender; TKCalendarMonthView interface @class TKMonthGridView,TKCalendarDayView; @protocol TKCalendarMonthViewDelegate, TKCalendarMonthViewDataSource; @interface TKCalendarMonthView : UIView { id <TKCalendarMonthViewDelegate> delegate; id <TKCalendarMonthViewDataSource> dataSource; NSDate *currentMonth; NSDate *selectedMonth; NSMutableArray *deck; UIButton *left; NSString *monthYear; UIButton *right; UIImageView *shadow; UIScrollView *scrollView; } @property (readonly,nonatomic) NSString *monthYear; @property (readonly,nonatomic) NSDate *monthDate; @property (assign,nonatomic) id <TKCalendarMonthViewDataSource> dataSource; @property (assign,nonatomic) id <TKCalendarMonthViewDelegate> delegate; - (id) init; - (void) reload; - (void) selectDate:(NSDate *)date; Thanks in advance for all your help! I still have a ton to learn, so I apologize if the question is absurd in any way. I'm going to continue researching this question right now!

  Read the article

• Problem getting correct parameters for C# P/Invoke call to C++ dll

  - by Jim Jones

  Trying to Interop a functionality from the Outside In API from Oracle. Have the following function: SCCERR EXOpenExport {VTHDOC hDoc, VTDWORD dwOutputId, VTDWORD dwSpecType, VTLPVOID pSpec, VTDWORD dwFlags, VTSYSPARAM dwReserved, VTLPVOID pCallbackFunc, VTSYSPARAM dwCallbackData, VTLPHEXPORT phExport); From the header files I reduced the parameters to: typedef VTSYSPARAM VTHDOC, VTLPHDOC * typedef DWORD_PTR VTSYSPARAM typedef unsigned long DWORD_PTR typedef unsigned long VTDWORD typedef VTVOID* VTLPVOID #define VTVOID void typedef VTHDOC VTHEXPORT, *VTLPEXPORT These are for 32 bit windows Going through the header files, the example programs, and the documentation I found: 1. That pSpec could be a pointer to a buffer or NULL, so I set it to a IntPtr.Zero (documentation). 2. That dwFlags and dwReserved according to the documentation "Must be set by the developer to 0". 3. That pCallbackFunc can be set to NULL if I don't want to handle callbacks. 4. That the last two are based on structs that I wrote C# wrappers for using the [StructLayout(LayoutKind.Sequential)]. Then instatiated an instance and generated the parameters by first creating a IntPtr with Marshal.AllocHGlobal(Marshal.SizeOf(instance)), then getting the address value which is passed as a uint for dwCallbackData and a IntPtr for phExport. The final parameter list is as follows: 1. phDoc as a IntPtr which was loaded with an address by the DAOpenDocument function called before. 2. dwOutputId as uint set to 1535 which represents FI_JPEGFIF 3. dwSpecType as int set to 2 which represents IOTYPE_ANSIPATH 4. pSpec as an IntPtr.Zero where the output will be written 5. dwFlags as uint set to 0 as directed 6. dwReserved as uint set to 0 as directed 7. pCallbackFunc as IntPtr set to NULL as I will handle results 8. dwCallBackDate as uint the address of a buffer for a struct 9. phExport as IntPtr to another struct buffer still get an undefined error from the API. Meaning that the call returns a 961 which is not defined in any of the header files. In the past I have gotten this when my choice of parameter types are incorrect. I started out using Interop Assistant which was helpful in learning how many of the parameter types get translated. It is however limited by how well I am able to glean the correct native type from the header files. For example the hDoc parameter used in the preceding function was defined as a non-filesytem handle, so attempted to use Marshal to create a handle, then used an IntPtr, and finally it turned out to be an int (actually it was &phDoc used here). So is there a more scientific way of doing this, other than trial and error? Jim

  Read the article

• Structuring Win32 GUI code

  - by kraf

  I wish to improve my code and file structure in larger Win32 projects with plenty of windows and controls. Currently, I tend to have one header and one source file for the entire implementation of a window or dialog. This works fine for small projects, but now it has come to the point where these implementations are starting to reach 1000-2000 lines, which is tedious to browse. A typical source file of mine looks like this: static LRESULT CALLBACK on_create(const HWND hwnd, WPARAM wp, LPARAM lp) { setup_menu(hwnd); setup_list(hwnd); setup_context_menu(hwnd); /* clip */ return 0; } static LRESULT CALLBACK on_notify(HWND hwnd, UINT msg, WPARAM wp, LPARAM lp) { const NMHDR* header = (const NMHDR*)lp; /* At this point I feel that the control's event handlers doesn't * necessarily belong in the same source file. Perhaps I could move * each control's creation code and event handlers into a separate * source file? Good practice or cause of confusion? */ switch (header->idFrom) { case IDC_WINDOW_LIST: switch (header->code) { case NM_RCLICK: return on_window_list_right_click(hwnd, wp, lp); /* clip */ } } } static LRESULT CALLBACK wndmain_proc(HWND hwnd, UINT msg, WPARAM wp, LPARAM lp) { switch (msg) { case WM_CREATE: return on_create(hwnd, wp, lp); case WM_CLOSE: return on_close(hwnd, wp, lp); case WM_NOTIFY: return on_notify(hwnd, wp, lp); /* It doesn't matter much how the window proc looks as it just forwards * events to the appropriate handler. */ /* clip */ default: return DefWindowProc(hwnd, msg, wp, lp); } } But now as the window has a lot more controls, and these controls in turn have their own message handlers, and then there's the menu click handlers, and so on... I'm getting lost, and I really need advice on how to structure this mess up in a good and sensible way. I have tried to find good open source examples of structuring Win32 code, but I just get more confused since there are hundreds of files, and within each of these files that seem GUI related, the Win32 GUI code seems so far encapsulated away. And when I finally find a CreateWindowEx statement, the window proc is nowhere to be found. Any advice on how to structure all the code while remaining sane would be greatly appreciated. Thanks! I don't wish to use any libraries or frameworks as I find the Win32 API interesting and valuable for learning. Any insight into how you structure your own GUI code could perhaps serve as inspiration.

  Read the article

• Python/Biophysics- Trying to code a simple stochastic simulation!

  - by user359597

  Hey guys- I'm trying to figure out what to make of the following code- this is not the clear, intuitive python I've been learning. Was it written in C or something then wrapped in a python fxn? The code I wrote (not shown) is using the same math, but I couldn't figure out how to write a conditional loop. If anyone could explain/decipher/clean this up, I'd be really appreciative. I mean- is this 'good' python- or does it look funky? I'm brand new to this- but it's like the order of the fxns is messed up? I understand Gillespie's- I've successfully coded several simpler simulations. So in a nutshell- good code-(pythonic)? order? c? improvements? am i being an idiot? The code shown is the 'answer,' to the following question from a biophysics text (petri-net not shown and honestly not necessary to understand problem): "In a programming language of your choice, implement Gillespie’s First Reaction Algorithm to study the temporal behaviour of the reaction A---B in which the transition from A to B can only take place if another compound, C, is present, and where C dynamically interconverts with D, as modelled in the Petri-net below. Assume that there are 100 molecules of A, 1 of C, and no B or D present at the start of the reaction. Set kAB to 0.1 s-1 and both kCD and kDC to 1.0 s-1. Simulate the behaviour of the system over 100 s." def sim(): # Set the rate constants for all transitions kAB = 0.1 kCD = 1.0 kDC = 1.0 # Set up the initial state A = 100 B = 0 C = 1 D = 0 # Set the start and end times t = 0.0 tEnd = 100.0 print "Time\t", "Transition\t", "A\t", "B\t", "C\t", "D" # Compute the first interval transition, interval = transitionData(A, B, C, D, kAB, kCD, kDC) # Loop until the end time is exceded or no transition can fire any more while t <= tEnd and transition >= 0: print t, '\t', transition, '\t', A, '\t', B, '\t', C, '\t', D t += interval if transition == 0: A -= 1 B += 1 if transition == 1: C -= 1 D += 1 if transition == 2: C += 1 D -= 1 transition, interval = transitionData(A, B, C, D, kAB, kCD, kDC) def transitionData(A, B, C, D, kAB, kCD, kDC): """ Returns nTransition, the number of the firing transition (0: A->B, 1: C->D, 2: D->C), and interval, the interval between the time of the previous transition and that of the current one. """ RAB = kAB * A * C RCD = kCD * C RDC = kDC * D dt = [-1.0, -1.0, -1.0] if RAB > 0.0: dt[0] = -math.log(1.0 - random.random())/RAB if RCD > 0.0: dt[1] = -math.log(1.0 - random.random())/RCD if RDC > 0.0: dt[2] = -math.log(1.0 - random.random())/RDC interval = 1e36 transition = -1 for n in range(len(dt)): if dt[n] > 0.0 and dt[n] < interval: interval = dt[n] transition = n return transition, interval if __name__ == '__main__': sim()

  Read the article

• counter and displaylist AS3

  - by VideoDnd

  How can I connect my counter to my display list?I've got a counter and a displaylist working, but I need help with everything in between. Try to explain I finished a Snowflake tutorial. The snowballs are children that are called to the stage. When connected to a dynamic variable, they move around and look like snow. I want my counter to move numbers around. I've got a counter, and I've got a 'for loop' to add children to the stage. link to file http://sandboxfun.weebly.com/ actionscript-3 //DISPLAYLIST "puts stuff on stage" for (var i:int = 0; i < 9; i++) { var t:MovieClip = new Tee(); t.x = 105 + i * 111; addChild(t);100 } //ARRAY //var o:Object = new Object(); <br> //var TeeProps:Dictionary= new Dictionary(true); <br> //var Tees:Array = new Array(); <br> //TeeProps[t] = o; <br> //addChild(t); <br> //Tees.push(t); <br> //} <br> //COUNTER drop in "mytext" text field to see it work var timer:Timer = new Timer(10); var count:int = 0; //start at -1 if you want the first decimal to be 0 var fcount:int = 100; timer.addEventListener(TimerEvent.TIMER, incrementCounter); timer.start(); function incrementCounter(event:TimerEvent) { count++; fcount=int(count*count/1000);//starts out slow... then speeds up // mytext.text = formatCount(fcount); } function formatCount(i:int):String { var fraction:int = i % 100; var whole:int = i / 100; return ("0000000" + whole).substr(-7, 7) + "." + (fraction < 10 ? "0" + fraction : fraction); } I'm rebuilding a earlier version for learning purposes.

  Read the article

• Would someone mind giving suggestions for this new assembly language?

  - by Noctis Skytower

  Greetings! Last semester in college, my teacher in the Computer Languages class taught us the esoteric language named Whitespace. In the interest of learning the language better with a very busy schedule (midterms), I wrote an interpreter and assembler in Python. An assembly language was designed to facilitate writing programs easily, and a sample program was written with the given assembly mnemonics. Now that it is summer, a new project has begun with the objective being to rewrite the interpreter and assembler for Whitespace 0.3, with further developments coming afterwards. Since there is so much extra time than before to work on its design, you are presented here with an outline that provides a revised set of mnemonics for the assembly language. This post is marked as a wiki for their discussion. Have you ever had any experience with assembly languages in the past? Were there some instructions that you thought should have been renamed to something different? Did you find yourself thinking outside the box and with a different paradigm than in which the mnemonics were named? If you can answer yes to any of those questions, you are most welcome here. Subjective answers are appreciated! hold N Push the number onto the stack copy Duplicate the top item on the stack copy N Copy the nth item on the stack (given by the argument) onto the top of the stack swap Swap the top two items on the stack drop Discard the top item on the stack drop N Slide n items off the stack, keeping the top item add Addition sub Subtraction mul Multiplication div Integer Division mod Modulo save Store load Retrieve L: Mark a location in the program call L Call a subroutine goto L Jump unconditionally to a label if=0 L Jump to a label if the top of the stack is zero if<0 L Jump to a label if the top of the stack is negative return End a subroutine and transfer control back to the caller exit End the program print chr Output the character at the top of the stack print int Output the number at the top of the stack input chr Read a character and place it in the location given by the top of the stack input int Read a number and place it in the location given by the top of the stack Question: How would you redesign, rewrite, or rename the previous mnemonics and for what reasons?

  Read the article

• Help with iphone dev - beyond bounds error

  - by dusk

  I'm just learning iphone development, so please forgive me for what is probably a beginner error. I've searched around and haven't found anything specific to my problem, so hopefully it is an easy fix. The book has examples of building a table from data hard coded via an array. Unfortunately it never really tells you how to get data from a URL, so I've had to look that up and that is where my problems show up. When I debug in xcode, it seems like the count is correct, so I don't understand why it is going out of bounds? This is the error message: 2010-05-03 12:50:42.705 Simple Table[3310:20b] *** Terminating app due to uncaught exception 'NSRangeException', reason: '*** -[NSCFArray objectAtIndex:]: index (1) beyond bounds (0)' My URL returns the following string: first,second,third,fourth And here is the iphone code with the book's working example commented out #import "Simple_TableViewController.h" @implementation Simple_TableViewController @synthesize listData; - (void)viewDidLoad { /* //working code from book NSArray *array = [[NSArray alloc] initWithObjects:@"Sleepy", @"Sneezy", @"Bashful", @"Bashful", @"Happy", @"Doc", @"Grumpy", @"Thorin", @"Dorin", @"Norin", @"Ori", @"Balin", @"Dwalin", @"Fili", @"Kili", @"Oin", @"Gloin", @"Bifur", @"Bofur", @"Bombur", nil]; self.listData = array; [array release]; */ //code from interwebz that crashes NSString *urlstr = [[NSString alloc] initWithFormat:@"http://www.mysite.com/folder/iphone-test.php"]; NSURL *url = [[NSURL alloc] initWithString:urlstr]; NSString *ans = [NSString stringWithContentsOfURL:url]; NSArray *listItems = [ans componentsSeparatedByString:@","]; self.listData = listItems; [urlstr release]; [url release]; [ans release]; [listItems release]; [super viewDidLoad]; } - (void)didReceiveMemoryWarning { // Releases the view if it doesn't have a superview. [super didReceiveMemoryWarning]; // Release any cached data, images, etc that aren't in use. } - (void)viewDidUnload { // Release any retained subviews of the main view. // e.g. self.myOutlet = nil; self.listData = nil; [super viewDidUnload]; } - (void)dealloc { [listData release]; [super dealloc]; } #pragma mark - #pragma mark Table View Data Source Methods - (NSInteger)tableView:(UITableView *)tableView numberOfRowsInSection:(NSInteger)section { return [self.listData count]; } - (UITableViewCell *)tableView:(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *)indexPath { static NSString *SimpleTableIdentifier = @"SimpleTableIdentifier"; UITableViewCell *cell = [tableView dequeueReusableCellWithIdentifier:SimpleTableIdentifier]; if (cell == nil) { cell = [[[UITableViewCell alloc] initWithStyle:UITableViewCellStyleDefault reuseIdentifier:SimpleTableIdentifier] autorelease]; } NSUInteger row = [indexPath row]; cell.textLabel.text = [listData objectAtIndex:row]; return cell; } @end

  Read the article

• Is Java assert broken?

  - by BlairHippo

  While poking around the questions, I recently discovered the assert keyword in Java. At first, I was excited. Something useful I didn't already know! A more efficient way for me to check the validity of input parameters! Yay learning! But then I took a closer look, and my enthusiasm was not so much "tempered" as "snuffed-out completely" by one simple fact: you can turn assertions off.* This sounds like a nightmare. If I'm asserting that I don't want the code to keep going if the input listOfStuff is null, why on earth would I want that assertion ignored? It sounds like if I'm debugging a piece of production code and suspect that listOfStuff may have been erroneously passed a null but don't see any logfile evidence of that assertion being triggered, I can't trust that listOfStuff actually got sent a valid value; I also have to account for the possibility that assertions may have been turned off entirely. And this assumes that I'm the one debugging the code. Somebody unfamiliar with assertions might see that and assume (quite reasonably) that if the assertion message doesn't appear in the log, listOfStuff couldn't be the problem. If your first encounter with assert was in the wild, would it even occur to you that it could be turned-off entirely? It's not like there's a command-line option that lets you disable try/catch blocks, after all. All of which brings me to my question (and this is a question, not an excuse for a rant! I promise!): What am I missing? Is there some nuance that renders Java's implementation of assert far more useful than I'm giving it credit for? Is the ability to enable/disable it from the command line actually incredibly valuable in some contexts? Am I misconceptualizing it somehow when I envision using it in production code in lieu of statements like if (listOfStuff == null) barf();? I just feel like there's something important here that I'm not getting. *Okay, technically speaking, they're actually off by default; you have to go out of your way to turn them on. But still, you can knock them out entirely.

  Read the article

• list of polymorphic objects

  - by LivingThing

  I have a particular scenario below. The code below should print 'say()' function of B and C class and print 'B says..' and 'C says...' but it doesn't .Any ideas.. I am learning polymorphism so also have commented few questions related to it on the lines of code below. class A { public: // A() {} virtual void say() { std::cout << "Said IT ! " << std::endl; } virtual ~A(); //why virtual destructor ? }; void methodCall() // does it matters if the inherited class from A is in this method { class B : public A{ public: // virtual ~B(); //significance of virtual destructor in 'child' class virtual void say () // does the overrided method also has to be have the keyword 'virtual' { cout << "B Sayssss.... " << endl; } }; class C : public A{ public: //virtual ~C(); virtual void say () { cout << "C Says " << endl; } }; list<A> listOfAs; list<A>::iterator it; # 1st scenario B bObj; C cObj; A *aB = &bObj; A *aC = &cObj; # 2nd scenario // A aA; // B *Ba = &aA; // C *Ca = &aA; // I am declaring the objects as in 1st scenario but how about 2nd scenario, is this suppose to work too? listOfAs.insert(it,*aB); listOfAs.insert(it,*aC); for (it=listOfAs.begin(); it!=listOfAs.end(); it++) { cout << *it.say() << endl; } } int main() { methodCall(); retrun 0; }

  Read the article

• How hard programming is? Really. [closed]

  - by Bubba88

  Hi! The question is about your perception of programming activity. How hard/exacting this task is? There is much buzz about programming nowadays, people say that programmers are smart, very technical and abstract at a time, know much about world, psychology etc.. They say, that programmers got really powerful brain thing, cause there is much to keep in consideration simultaneously again with much information folded into each other associatively (up 10 levels of folding they say))) Still, there are some terms to specify at our own.. So that is the question: What do you think about programming in general? Is it hard? Is it 'for everyone' or for the particular kind of people only? How much non-CS background do you need to program (just to program, really; enterprise applications for example)? How long is the learning curve? (again, for programming in general) And another bunch of random questions: - If you were not to like/love programming, would that be a serious trouble bothering your current employment? - If you were to start from the beginning, would you chose that direction this time? - What other areas (jobs or maybe hobbies) are comparable to programming in the way they can explode someone's lovely brain? - Is 'non turing-complete programming' (SQL, XML, etc.) comparable to what we do or is it really way easier, less requiring, cheap and akin to cooking :)? Well, the essence is: How would you describe programming activity WRT to its difficulty? Or, on the other hand: Did you ever catch yourself thinking at some point: OMG, it's sooo hard! I don't know how would I ever program, even carried away this way and doing programming just for fun? It's very interesting to know your opinion, your'e the programmers after all. I mean much people must be exaggerating/speculating about the thing they do not really know about. But that musn't be the case here on SO :) P.S.: I'll try my best to update this post later, and you please edit it too. At least I'll get decent English in my question text :)

  Read the article

• What Can I Do To One Of My Team Number (Good Friend As Well) Who Lost His Passion.

  - by skyflyer

  It seems this question is not program related, but there are lot of similar questions. So please bear with me! By the way, I am programmer and my team is also charging a software project. And SO is the only place which solved me lot of thorny troubles!THANK YOU GUYS! I joined my company with him years ago. At that time he was quite passionate on his job which is a front-end development. He gave us lot of useful suggestions concerning his work like design. And I believed he was a smart guy. I believe he still is smart too by the way. One years later, however, he seemed lost his passion and fooling around every day, did not care about his work any more and produced poorwork. Even worse he literally stopped learning new skills and honing his work related skills. For me it is horrible, we got to keep abreast with new technology development, otherwise we will be throw out. Since we were just coworkers, I did not care about it too much except mentioned my thoughts several times. But last month, we resembled a new group and assigned very important project. And I am the team leader, sadly! My boss gave me lot of support and expectation as well. I did a pretty good job before and I am very optimism to our future. But as a team, if my team does not work hard, we will be doomed to failure no matter how hard I work and push. In order to revitalize his passion, I tried couple of ways like talking to him about my concern and my boss's angry. I offered his new task which is quite new to him. I even persuaded my boss to give him new incentive package. But all of them knocked wall. His reaction was just he did not care. Even worse he did not want to talk about his situation. I want to be hard on him, but since we are friends and coworkers, I really can not see it will work. Even it works, I can not so quickly change my self from friend and coworker into manager. As a novice in management, I am really overwhelmed! I do not want get him fired, we are friends and I do not see him fired as my team number. What can I do? Thank you guys!

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >