Search Results

Search found 15139 results on 606 pages for 'scripting interface'.

Page 250/606 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

• What LTO 4 drive to buy

  - by pplrppl

  Evan Anderson mentioned in another solution you could buy a LTO-4 (autoloader, 1 tape / day) - $4,566.00 (the discussion included total cost of tapes for a specific rotation.) but I don't know specifics on what he or you would recommend for the actual drive and if necessary controller. Show me a newegg URL or CDW, Dell, or HP, or whatever your favorite vendor would be for your solution if you don't mind looking it up or just give me a brand and a model number and I'll be glad to do the leg work myself. I currently have on have on hand an external LTO 3 drive that uses LVD SCSI interface (and thus have a controller card that has an external LVD SCSI connector). If that card isn't sufficient to interface to a LTO 4 drive let me know. http://www.fujifilmusa.com/shared/bin/LTO_Overview.pdf shows minimum tape speeds for LTO4 and other LTO formats. It looks like the IBM LTO4 actually has a lower minimum speed than the IBM LTO3. Either way my average server is too slow to feed LTO3/4 without shoeshining so I'm looking for a drive with a low minimum write speed. If you trust the PDF from 2008 that makes my choices IBM LTO 4 full height IBM LTO 4 half height HP LTO 4 half height but presumably there are other options out there that weren't mentioned in the fuji PDF. Again I'm looking for a specific recommendation on a drive to buy (and the controller if needed).

  Read the article

• Debian Linux bridging router intermittently dropping packets [migrated]

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• Public-to-Public IPSec tunnel: NAT confusion

  - by WuckaChucka

  I know this is possible -- and apparently fairly common with larger companies that don't/can't route private addresses for overlap reasons -- but I can't wrap my head around how to get this to work. I'm playing around with pfSense, Vyatta and a Cisco 5505 right now, hardware-wise. So here's my setup: WEST: Vyatta outside: 10.0.0.254/24 inside: 172.16.0.1/24 machine a: 172.16.0.200/24 EAST: Cisco 5505 outside: 10.0.0.210/24 inside: 192.168.10.1 machine b (webserver): 192.168.10.2 So what we're trying to do is this: route traffic across the tunnel from machine A to machine B without using private addresses. i.e. 172.16.0.200 makes a TCP request to 10.0.0.210:80, and as far as EAST is concerned, it sees a src IP of 10.0.0.254. On WEST, I have your typical many-to-one Source NAT to translate 172.16.0.0/24 to 10.0.0.254 and that's confirmed to be working. Also on WEST, I have the following IPSec config: Local IP: 10.0.0.254 Peer IP: 10.0.0.210 local subnet: 10.0.0.254/32 remote subnet: 10.0.0.210/32 I have the reversed configuration on EAST. What happens when I make a request from machine A to 10.0.0.210:80 is that the SNAT translates the private address of machine A to 10.0.0.254 and it's routed out (and discarded at the other end) without establishing the tunnel. What I'm assuming is happening is that the inside interface on WEST receives a packet from 172.16.0.200 and since this doesn't match the local subnet defined in the tunnel configuration, it's not processed by the IPSec engine and the tunnel is not established. How do you make this work? Seems like a chicken and egg thing with the NAT and IPSec and I just can't wrap my head around how this can be done: can I say, "if a packet is received on the inside interface with a destination of 10.0.0.210, translate it to 10.0.0.254 before the IPSec engine inspects it"?

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan Hogervorst

  Hello, I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• Easy GUI way to auto scale EC2 and RDS: aws console, scalr, ylastic...?

  - by Zillo

  I am managing all my instances with the AWS Management Console (the GUI web console) but now I want to use Auto Scale and it seems that this can not be done with that console. Yes, there is CloudWatch but I can only create alarms (e-mail notifications), it seems that CouldWatch needs you to add the auto scale policy in some other place (by command line console?). I would like to use some easy GUI interface. Ylastic and Scalr seems to be a good option. Which one do you think is better? Regarding Scalr, is there any difference between the open source software Scalr and the service Scalr.net? I mean, is the GUI interface the same? I like the idea of the Scalr because I do not need to give my Secret Access Key to a third party (like in Ylastic or in Scalr.net) One question about the Scalr software, it has to be installed in the instances or it must be installed in another machine? Do I need to setup again all my security permissions, AMIs, snapshots, etc. or I can use AWS Management Console for everything and Scalr just to auto scale.

  Read the article

• How to setup an IPSec / GRE tunnel on Windows Server 2008

  - by qbeuek

  I have a Windows Server 2008 that has a single network interface configured with a public IP address. My business partner has a private network. From my server, I need to access all the devices on his private network, and those devices must be able to access my server. My business partner has a standard solution for these requirements. They will setup an IPSec + GRE tunnel to my server. They told me, that I will need an additional public IP address for this to work. If it really is necessary, there is no problem, I can get an additional public IP address, although it will be assigned to the same physical network interface. I assume that on my server I will have both public IP addresses and also the private IP address from the tunnel (the same that is visible for the devices inside the private network). What alternatives do I have? Is it possible to configure this tunnel on my Windows Server 2008? Can it be done using only Windows tools, or do I need an additional free / commercial VPN software? If it cannot be done directly on Windows, can I setup an additional virtual machine running Linux, that will handle the IPSec + GRE tasks? How to do it? If it cannot be done on a virtual linux box, will I have to buy and setup a Cisco router to handle the IPSec + GRE tasks? Thanks for your opinions. I'm watching this question to clarify any issues or questions.

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Public static ip for vagrant box

  - by Numbata

  I have server (Debian Squeeze) with 1 ethernet card and 2 public static IPs (188.120.245.4 and 188.120.244.5). What I want: Setup virtual box (Ubuntu) with access via static IP (188.120.244.5). What I was trying: config.vm.forward_port - good idea: setup interface "eth1:1" with 188.120.244.5 on host-machine, and add to Vagrant file "config.vm.forward_port = hmm..?" config.vm.network :hostonly, "188.120.244.5" - not working. Was created new interface on host-machine with ip "188.120.244.1". Of course 188.120.244.1 IP isn't mine and I can't access my server via this IP. config.vm.network :bridged - I'm confused how this works :) What I have now: Not working configuration. Debian-host-machine# cat Vagrantfile Vagrant::Config.run do |config| config.vm.define :gitlab do |box_config| box_config.vm.box = "ubuntu" box_config.vm.host_name = "ubuntu" box_config.vm.network :bridged box_config.vm.network :hostonly, "188.120.244.5", :auto_config => false end end Debian-host-machine# ifconfig eth1 Link encap:Ethernet HWaddr 00:15:17:69:71:bb inet addr:188.120.245.4 Bcast:188.120.247.255 Mask:255.255.248.0 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:188.120.244.1 Bcast:188.120.246.255 Mask:255.255.255.0 Ubuntu-virtual-machine# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:ee:8d:0c inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 eth1 Link encap:Ethernet HWaddr 08:00:27:45:71:87 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 How I can access virtual box via public static IP from network? I'm using Oracle VM VirtualBox Manager 4.1.18 and Vagrant version 1.0.3. Thanks in advance for your feedback.

  Read the article

• I need scanning software to use with my scanner.

  - by D Connors

  So, I got this (HP F4280) printer/scanner about a year ago, and I'm really happy with it. The only thing is that I never really liked the HP scanning software that came with it. A few months ago I reformatted and reinstalled windows 7. Then, once I plugged in the printer, I noticed that windows recognized it automatically, and offered to install all the drivers by itself. So instead of manually installing the driver that came in the CD, I simply let windows automatically install it from its servers, and so far it's great. Instead of HP's scanning software (that really wasn't pleasing me), I got a very simplified interface that is more than enough for my ocasional scanning habits. Until today. Today I had to scan a bunch of old pictures for my father. And that simple interface felt like it was lacking quite a few features to make this repetitive task a little easier. And that's why I'm now looking for a good software to use for scanning. By "good" I mean anything well thought out, and specially anything that will make my life easier when repetitive-scanning. It doesn't need to have professional tweaking options, but having them is not a problem either. You guys got anything?

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

• Disk Error on Boot (Possible boot sector issue)

  - by Choco

  I own a 4-5 year old Dell Dimension E510 with Windows XP: Media Center Edition. I have 2 drives installed: C Drive: Windows XP: Media Center Edition G Drive: 2 partitions: Windows 7 (beta) Windows XP (professional) That is also the order they are connected. The C Drive is my primary drive. When I attempt to boot the computer, the bios loading screen appears normally; the progress bar moves and it's fine. The very next page, however, supposed to be a boot choice. When I installed Windows 7 onto the G Drive in context of the C drive it added a boot selector to the C drive's boot sequence. It gives me the option of booting Windows 7 or Windows XP: Media Center Edition. However, my problem is now this: After the bios screen I previously mentioned, instead of a boot selector, I receive the following error: A disk read error occurred. Press CTRL+ALT+DEL to restart. The drive is spinning up normally. I hear no odd noises/clicks/scraping coming from it, even after disabling the other drive to listen to it carefully. According to me, it's a boot sector issue. I have never experienced this before, but maybe during a recent shutdown, Windows XP: MCE errored out and ruined the boot sector. Dilemma! I don't have the Windows XP: MCE disc, because it was installed by the factory. I have accessed the hidden partition on the drive before (you hit a key combination on the bios screen and it comes up with an interface to fix your drive). However, I don't want to reformat the drive (which is what the interface gives me the option to do). I want to possibly fix the boot sector. How can I achieve that?

  Read the article

• Mac: window manager frozen, have ssh access

  - by Bernd

  I have a Mac which regularly runs into a problem. The user interface stops reponding, showing a "frozen" user interface. The mouse is still moving but clicking does not trigger anything. This happens about once a week. Solution so far is to force switch-off the Mac and reboot it. I have ssh root access to the Mac. Killing (kill -9) the active application has no visible impact on what is shown on the screen. Any ideas on how to diagnose this? Is there a way to restart the window manager from the ssh shell? Killing /System/Library/Frameworks/ApplicationServices.framework/Frameworks/CoreGraphics.framework/Resources/WindowServer seems not to be possible. The Mac is an early 2008 iMac and runs Lion with latest updates. /Library/Logs/DiagnosticReports is empty. Update: Problem stays after update to Mountain Lion. The WindowServer process is in "uninterruptible wait" state ("U" flag in ps output set): imac:~ root# ps ax|awk "NR==1|| /WindowServer/"|grep -v awk PID TT STAT TIME COMMAND 86 ?? Us 50:51.69 /System/Library/Frameworks/ApplicationServices.framework/Frameworks/CoreGraphics.framework/Resources/WindowServer -daemon Any idea for diagnosing what blocks the process? Any idea for "waking up" the process?

  Read the article

• Managing ip6tables (or an alternative firewall) remotely

  - by Matthew Iselin

  I'm working with IPv6 and have run into an issue configuring ip6tables on our main router in order to control what can come into the network. A default DROP rule in the FORWARD section has worked well (obviously leaving ESTABLISHED,RELATED as ACCEPT) to keep internal clients' open ports from being accessed. However, running an ip6tables command for every little change is unwieldy. Whilst we are able to continue creating rules manually, I'm wondering if there's some sort of management interface we could use to create the rules quickly and easily. We're looking to be able to save time working on our firewall as well as providing a simple method for modifying rules for those who will eventually replace us. I know webmin (heavily locked down on our network, naturally) has support for modifying iptables rules, but seemingly no support for ip6tables. Something similar would be fantastic. Alternatively, suggestions for a firewall solution apart from iptables/ip6tables which can be managed remotely wouldn't be out of order. A web interface for management is certainly preferable, even if it is just a wrapper with shiny buttons over the raw config files.

  Read the article

• Troubleshooting loss of network connectivity in Windows 2003 - What else to check?

  - by Benny

  We are facing a weird problem in our data center. Our Backup server (running EMC Networker) loses network connection every alternate day around 3:00 AM (Backup schedule starts at midnight). After 2 hours of outage, the network connectivity recovers automatically and back to normal. What we observed: It is unlikely to be network issue, since it is directly connected to server farm switch (layer 2 connection without any intermediate hops). Further, the server is connected to two different switches for Load balancing using Broadcomm Teaming. a) If it were a switch related issue it is unlikely that both the network ports go down, since they are connected to different switch. b) A possibility Vlan wide issue is also ruled out since other devices in the same Vlan are fine. c) Switch interface status is always up. But there are lot of packet drops during the outage period - Can be attributed to high interface utilization of the backup server (near 100%) d) Connectivity is restored without any change on network. Next suspect is resource utilization on Windows server. Both CPU and Memory have rarely exceeded 80%, but NIC card utilization is alarmingly high (near 100%) Not really sure how to investigate this?

  Read the article

• Wireless driver activation problem in compaq c700 in ubuntu 9.04

  - by Fazil

  I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

  Read the article

• Performance monitoring on Linux/Unix

  - by ervingsb

  I run a few Windows servers and (Debian and Ubuntu) Linux and AIX servers. I would like to continously monitor performance on these systems in order to easily identify bottlenecks as well as to have an overview of the general activity on the servers. On Windows, I use Windows Performance Monitor (perfmon) for this. I set up these counters: For bottlenecks: Processor utilization : System\Processor Queue Length Memory utilization : Memory\Pages Input/Sec Disk Utilization : PhysicalDisk\Current Disk Queue Length\driveletter Network problems: Network Interface\Output Queue Length\nic name For general activity: Processor utilization : Processor\% Processor Time_Total Memory utilization : Process\Working Set_Total (or per specific process) Memory utilization : Memory\Available MBytes Disk Utilization : PhysicalDisk\Bytes/sec_Total (or per process) Network Utilization : Network Interface\Bytes Total/Sec\nic name (More information on the choice of these counters on: http://itcookbook.net/blog/windows-perfmon-top-ten-counters ) This works really well. It allows me to look in one place and identify most common bottlenecks. So my question is, how can I do something equivalent (or just very similar) on Linux servers? I have looked a bit on nmon (http://www.ibm.com/developerworks/aix/library/au-analyze_aix/) which is a free performance monitoring tool developed for AIX but also availble for Linux. However, I am not sure if nmon allows me to set up the above counters. Maybe it is because Linux and AIX does not allow monitoring these exact same measures. Is so, which ones should I choose and why? If nmon is not the tool to use for this, then what do you recommend?

  Read the article

• Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

  - by jamieb

  I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• how do you add an A record for a root domain

  - by nbv4

  this seems really simple, but I can't figure it out. I'm using xname.org since it's free and I own a bunch of domains spread over a few different registrars. The setup I desire is very simple: one A record that points the bare domain name to my server, plus a wildcard CNAME record pointing all subdomains to the same server. So if the user goes to domain.com it will point them to 285.24.435.75, if they go to www.domain, blah.domain.com, or any other sub domain, they'll get sent to 285.24.435.75. All the examples I read on the internet about setting up A records all have the A record set to a subdomain such as www. WWW is deprecated so I want to have noting to do with it. Currently my xname.org zone looks like this: $TTL 86400 ; Default TTL domain.com. IN SOA ns0.xname.org. nbvfour.gmail.com. ( 2010052503 ; serial 10800 ; Refresh period 3600 ; Retry interval 604800 ; Expire time 10800 ; Negative caching TTL ) $ORIGIN domain.com. IN NS ns2.xname.org. IN NS ns0.xname.org. IN NS ns1.xname.org. @ IN A 65.49.73.148 * IN CNAME domain.com The '@' symbol is something that the godaddy domain interface uses to mean "this root domain', but that may have been specefic to that interface and has no meaning here. Before I had a 'www' entry in the A rcords and it worked in the sense that I could ping 'www.domain.com' and it returned a response, but pinging the root domain 'domain.com' returned "no host found".

  Read the article

• Cisco ASA user authentication options - OpenID, public RSA sig, others?

  - by Ryan

  My organization has a Cisco ASA 5510 which I have made act as a firewall/gateway for one of our offices. Most resources a remote user would come looking for exist inside. I've implemented the usual deal - basic inside networks with outbound NAT, one primary outside interface with some secondary public IPs in the PAT pool for public-facing services, a couple site-to-site IPSec links to other branches, etc. - and I'm working now on VPN. I have the WebVPN (clientless SSL VPN) working and even traversing the site-to-site links. At the moment I'm leaving a legacy OpenVPN AS in place for thick client VPN. What I would like to do is standardize on an authentication method for all VPN then switch to the Cisco's IPSec thick VPN server. I'm trying to figure out what's really possible for authentication for these VPN users (thick client and clientless). My organization uses Google Apps and we already use dotnetopenauth to authenticate users for a couple internal services. I'd like to be able to do the same thing for thin and thick VPN. Alternatively a signature-based solution using RSA public keypairs (ssh-keygen type) would be useful to identify user@hardware. I'm trying to get away from legacy username/password auth especially if it's internal to the Cisco (just another password set to manage and for users to forget). I know I can map against an existing LDAP server but we have LDAP accounts created for only about 10% of the user base (mostly developers for Linux shell access). I guess what I'm looking for is a piece of middleware which appears to the Cisco as an LDAP server but will interface with the user's existing OpenID identity. Nothing I've seen in the Cisco suggests it can do this natively. But RSA public keys would be a runner-up, and much much better than standalone or even LDAP auth. What's really practical here?

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by mfn

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >