Search Results

Search found 8979 results on 360 pages for 'dynamic routing'.

Page 258/360 | < Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >

• Only tunnel certain applications via OpenVPN

  - by jinjin

  Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

  Read the article

• How can I create a VLAN on my extreme switch for a separate subnet/domain?

  - by drpcken

  I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). Switch is a Summit x450e-48p My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

  Read the article

• How should I deploy my JVM-based web application on ubuntu?

  - by Pieter Breed

  I've developed a web application using clojure/compojure (JVM based) and while developing I tested it using embedded jetty that runs on 0.0.0.0:8080. I would now like to deploy it to run on port 80 on ubuntu. I do dynamic virtual hosting, so any request for any host that arrives on port 80 should be handled by my application. The issues that worries me are: I can still run it embedded but I'm worried about running my app as root (needed for binding to port 80). I'm not sure if I can 'give up root' when in the JVM. Do I need to be concerned by this? besides, serving web applications is a known problem and I should be using known solutions for this (jetty or tomcat) but especially tomcat seems very heavy weight. Besides, I only have one application that listens to /* and does routing internally. (with compojure/ring). What I'm trying to say with this is that tomcat by default assigns WARs to subfolders which I don't want. So basically what I need is some very safe way of binding to port 80 on ubuntu that can with minimal interference send all requests to my app. Any ideas?

  Read the article

• AWS: Multi-region setup using single RDS instance

  - by Ion

  I'm trying to scale our web application (PHP, MySQL, memcache) in a multi-region scheme. Currently we are using a setup with two EC2 instances behind an ELB and an RDS instance, all of them in US-EAST (Virginia) region. We would like to have a presence in the EU (Ireland) region as well. This means at least a new EC2 instance there (identical to the others, serving the same application). I have copied the desired AMI, setup the new instance, setup a same ELB configuration (required for SSL termination) and configured latency-based routing in Route53. And it works as suggested. But, clients from EU have speed problems. This is due to the fact that the EU EC2 instances connect to the US-based RDS instance. As far as I know Amazon has not yet enabled RDS multi-region replication. Do you have any suggestions on how to properly speed up the whole setup while using the single RDS instance? Also, any ideas in general on how to scale things up? Ideally we would like to continue using the RDS technology for various reasons. Nevertheless, I am open to suggestions (I guess the next idea would be to host our own MySQL servers).

  Read the article

• How Does EoR Design Work with Multi-tiered Data Center Topology

  - by S.C.

  I just did a ton of reading about the different multi-tier network topology options as outlined by Cisco, and now that I'm looking at the physical options (End of Row (EoR) vs Top of Rack(ToR)), I find myself confused about how these fit into the logical constructs. With ToR it also maps 1:1: at the top of each rack there is a switch(es) that essentially act as the access layer. They connect via fiber to other switches, maybe chassis-based, that act as the aggregation layer, that then connect to the core layer. With EoR it seems that the servers are connecting directly to the aggregation layer, skipping the access layer all together, by plugging directly into what are typically chassis switches. In EoR then is the standard 3-tier model now a 2-tier model: the servers go to the chassis switch which goes straight to the core switch? The reason it matters to me is that my understanding was that the 3-tier model was more desirable due to less complexity. The agg switch pair acts as default gateway and does routing; if you use up all of your ports in your agg layer pair it's much more complicated to add additional switches, than simply adding more switches at the access layer. Are there other downsides to this layout? Does this 3-tier architecture still apply in some way in EoR? Thanks.

  Read the article

• Windows 7 ICS client web failure

  - by n8wrl

  I have several windows 7 PC's connected on a LAN via a hub. One has a Verizon 3G connection and works great. I have internet connection sharing enabled on it, which automagically set the LAN connection to 192.168.137.1 and enabled DHCP. I am trying to get the client PC's working one at a time. The others are off. The client is able to: Get an IP via DHCP with correct settings. Ping any web address I can throw at it, so DNS and routing are working. Windows update works. But web sites hang in IE. All but google.com! I type www.msn.com, microsoft.com, amazon.com, etc. etc. All ping via a cmd window but IE just hangs - it says web site found but the green progress bar just slowly creeps and no content displays. www.google.com comes up even after clearing browser and dns cache. I am pulling my hair out - what am I missing? EDIT: After some more gyrations with a router I'm back to ICS. Same symptoms, only now I have an answer to Andrew's question, YES I can do Google searches but clicking on any of the result links hangs! Let one sit for half an hour with no timeout or error.

  Read the article

• Mangling traffic from a Mikrotik Router

  - by TiernanO

  I have a MikroTik powered Router in the house with a couple of internet connections (2 200/10Mb Cable modems and a 100/20Mb VDSL Line). I am using Mangle rules to set routing marks and NAT rules to do some load balancing, and everything seems to be going grand... But it only works for traffic from outside the router... Let me explain: I have 4 GigE ports on the machine, WAN1,2 and 3, and a LAN port named LAN1. All traffic from LAN1 is getting mangled (as it should be) but traffic from the load router itself (proxy traffic, IPv6 tunnels, VPN connections) are not being mangled. They get the first route to 0.0.0.0/0, which in my case is WAN2, and stick with it. So, how do I get traffic from the local router to be mangled? Originally it was proxy traffic that caused the problem, but now with IPv6 and VPN, they are more important to be mangled... last time i enabled IPv6 traffic, all traffic only went though WAN2, and the rest where unused... Any ideas?

  Read the article

• In Stud, which Private RSA Key should be concatenated in the x509 SSL certificate pem file to avoid "self-signed" browser warning?

  - by Aaron

  I'm trying to implement Stud as an SSL termination point before HAProxy as a proof of concept for WebSockets routing. My domain registrar Gandi.net offers free 1-year SSL certs. Through OpenSSL, I generated a CSR which gave me two files: domain.key domain.csr I gave domain.csr to my trusted authority and they gave me two files: domain.cert GandiStandardSSLCA.pem (I think this is referred to as the intermediary cert?) This is where I encountered friction: Stud, which uses OpenSSL, expects there to be an "rsa private key" in the "pem-file" - which it describes as "SSL x509 certificate file. REQUIRED." If I add the domain.key to the bottom of Stud's pem-file, Stud will start but I receive the browser warning saying "The certificate is self-signed." If I omit the domain.key Stud will not start and throws an error triggered by an OpenSSL function that appears intended to determine whether or not my "pem-file" contains an "RSA Private Key". At this point I cannot determine whether the problem is: Free SSL cert will always be self-signed and will always cause browser to present warning I'm just not using Stud correctly I'm using the wrong "RSA private key" The CA domain cert, the intermediary cert, and the private key are in the wrong order.

  Read the article

• Can't reliably ping 6224 router from directly-attached system

  - by David Mackintosh

  OK, here's my situation. This is on the internet. The 6224 is the router in this picture and physically resides in Kanata. Both VLAN 1697 and 3994 are provided by an internet service provider. These VLANs are provided through a single 1Gb ethernet wire. The Kanata hosts are directly attached to the 6224; the other two sites are remote. VLAN 3994 is a single IP address space, so theoretically it shouldn't matter physically where the hosts on that subnet are. Here's the problem. I have a monitoring system which is connected further into the internet, so probes from the monitor would come in to this diagram on the 1697 VLAN. When I ping hosts at Albert or Bells Corners from the internet, there is 0 loss. The connection looks perfect. When I ping hosts at Kanata, I lose anywhere from 10 to 40% of the pings. The loss is not predictable, but: when I do lose them, I always lose at least 3, usually 4, rarely more, pings in a bunch. I have attached a monitor directly to the 6224 in Kanata on 3994.. When the monitor pings the 6224 routing interface, I see exactly the same loss pattern -- but NOT at the same time as the loss from the remote system. Ping time is around 1ms. When the monitor pings another system directly attached to the 6224, there is 0 loss. Ping time is about 0.1ms, one-tenth of the time to ping the router. Anyone know what is going on here?

  Read the article

• Remote Desktop fails after VPN connection

  - by Samet Sorgut

  The local computer (comp 1) is connected to a remote computer (comp 2) with Remote Desktop. On the remote computer (comp 2), I try to establish an VPN connection to a different remote computer (comp 3). Once I try to establish the VPN connection from the remote computer (comp 2) to the second remote computer (comp 3), Remote Desktop freezes on comp 1. It is not possible to connect to comp 2 again via Remote Desktop. What can be done to connect to this remote computer (comp 2) after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest? EDIT: I want to use the internet connection of the VPN, so all traffic should go over the VPN but still RDP working. My IP: 100.0.0.1 The IP where I'm connecting via RDP: 200.0.0.20 (Mask: 255.255.255.192, Gateway: 200.0.0.193) Where the 200.0.0.1 connects to VPN the IP of the VPN is: 65.254.61.250 Will routing like this help (Command is issued in 200.0.0.20, the RDP location): route ADD 65.254.61.250 MASK 255.255.255.192 200.0.0.193 Couldn't add gives the error: The route addition failed: The parameter is incorrect. I tried before connecting to VPN.

  Read the article

• Advertise a subnet route with radvd

  - by Thomas Berger

  we have set up a small IPv6 Testing network. The setup looks like this: ::/0 +----------+ | Firewall | Router to the public net +----------+ | 2001:...::/106 | +----------+ +-------| SIT GW | sit Tunnel gatway to the some test users | +----------+ | +----------+ | Test Sys | Testsystem +----------+ The idea is to advertise the default route from the firewall and the route for the SIT subnets from the sit gateway. The configurations for radvd are: # Firewall interface eth0 { AdvSendAdvert on; route ::/0 { }; }; # SIT Gatway interface eth0 { AdvSendAdvert on; route 2001:...::/106 { }; }; We have captured the adv. packages with tcpdump and the packages looks good. We see a default route from the fw, and the subnet route from the SIT gatway. But if we look on the testsystem there are two default routes over both gateways. There is no subnet route. The routing does not work of course. Here the routes we get: 2001:.....::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::baac:6fff:fe8e:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 default via fe80::e415:aeff:fe12:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 Any Idea?

  Read the article

• How can I create a VLAN on my extreme switch for a seperate subnet/domain?

  - by drpcken

  I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

  Read the article

• Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

  - by Ikon

  I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Why not block ICMP?

  - by Agvorth

  I think I almost have my iptables setup complete on my CentOS 5.3 system. Here is my script... # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP For context, this machine is a Virtual Private Server Web app host. In a previous question, Lee B said that I should "lock down ICMP a bit more." Why not just block it altogether? What would happen if I did that (what bad thing would happen)? If I need to not block ICMP, how could I go about locking it down more?

  Read the article

• "Error 53" with local LAN machines after VPN session on server

  - by tim11g

  I have a Windows 2000 server with a Windows 7 client that occasionally gets "error 53" when accessing the server by name (net view \\server). It still works by IP address (net view \\192.168.0.1). The server's primary IP address (as shown in "routing and remote access" as "Gigabit Ethernet" is 192.168.0.1. There is also a secondary IP address shown as "Internal" which is 192.168.0.50 The server also supports VPN. When a VPN user connects, it gets an address in the range of 192.168.0.51 to .59. Normally (when there is no error), when the local LAN client runs "ping server", it resolves to 192.168.0.1. When the Error 53 problem happens, "ping server" resolves to 192.168.0.50. This problem seems to be related to when a user connects or has recently connected to the server VPN. Is there some connection between the VPN services on the server and the DNS services on the server that could cause a local LAN client to become confused about which IP address to use for the server? Or is there a misconfiguration in the VPN or DNS?

  Read the article

• Postfix auto create Maildir

  - by Eugene

  I've been beating my head against a wall for a while now on this one. Basically, here is the rundown: Our MX record points to a frontend SMTP server, which contains aliases for actually routing the mail. No alias, no access to the backend storage server, which is what our clients connect to. I'm upgrading the backend email server. Currently, a user is created for every email user on the server, which creates the mailbox. On the new server, everything autheticates through PAM to an LDAP server (all of which is working properly). My goal is to get Postfix to create the Maildir directory for the user automatically. This works fine when I have the /home directory with 777 permissions, but for obvious reasons, this should be avoided. I would like to do this with 775 permissions on /home with a group owner of whatever user Postfix is running as, but I can't seem to figure out what user to use. With the 777 permissions, the /home/$user/Maildir directory is created on message delivery. Does anybody know how I can do this without 777 permissions? The system I am working on is a 64-bit Debian Lenny 5.07 install. Any advice would be appreciated.

  Read the article

• Gmail: Received an email intended for another person. [closed]

  - by jonescb

  I'm not really sure how email routing works, but someone ordered something on Amazon and I received the email instead of them. Or maybe we both got it, I don't know. The order doesn't show up in my account, so I'm certain I wasn't charged for it, but I shouldn't be getting other peoples' emails. We'll say that my email is [email protected], and somebody who's email is [email protected] places an order on Amazon. The confirmation email is sent to me at [email protected]. I checked the email header, and it did say To: [email protected] which is not my email address. At first I thought that Google ignores periods in email addresses, but I tested the account setup and it doesn't give any error when you put a period in the address. I didn't create the account; I just used the "check availability" function and the address I chose with a period was fine. Maybe someone with knowledge about how Email works could tell me why this happened. Is this a bug in the way Amazon sends emails? Or is it a bug in how Google receives them? Who should I report this issue to?

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• Apache suddenly very slow on http and faster on https

  - by hsnm

  Background: I have Apache 2 running on ubuntu. There is a low usage on it and mostly being accessed for a web service URL from mobile apps. It was working fine until I installed SSL certificates. I now have both http and https. When I access the server using https, I get a fairly quick response (but probably not as fast as before). When I use http, it's so slow. What I tried: From this post: I curl localhost from the host and it takes some time, meaning there is no routing issue. The server runs on Amazon EC2 instance and is managed by me only. Also: I see that Apache once running, creates the maximum number of processes it is allowed to, which was not the case before. I lowered the MaxClients to 20 and I think I'm getting faster responses but it still takes over a minute and I always have MaxClients Apache processes. dmesg returns many [ 1953.655703] TCP: Possible SYN flooding on port 80. Sending cookies. When I netstat I get many entries with SYN_RECV. Possibly a DDoS attack? From EC2's monitoring diagrams I see a pattern of high "Maximum Network In (Bytes)" since 2 days ago. By the way the server is still being tested, the actual traffic is very low and not consistent. I tried to go with this solution to limit incoming connections using iptables, still no luck, but I'm trying. Question: What could be the problem? Is this a DDoS attack?

  Read the article

• Can sendmail be configured to discard routed email that has been rejected by the next hop?

  - by Guy Bolton King

  Background: We have a handful of hosts (running sendmail) acting as the MXs for a few domains each. Each domain is handled via the sendmail/cf /etc/mail/virtusertable, with a set of known recipients and a catch-all reject rule. Mail to postmaster on each host is aliased to root, and root is aliased to root+<host>@ourdomain.com. The MX for ourdomain.com is Google Apps, and [email protected] is a simple group that forwards to the admins. Google Apps will reject some emails at the SMTP stage, usually because of illegal attachments (instead of accepting them and filing them as spam). Problem: Given a particular spam email sent to a domain in a virtusertable entry: If the recipient address rejects the mail, then sendmail will try and send a DSN to the sender. If that sender also rejects the mail (because it's a falsified sender, and the MX for the sender rejects the mail as spam), then sendmail sends a DSN to the postmaster. The routing detailed above takes place, and...Google Apps rejects the mail as well. sendmail now gives up with a "savemail panic", and leaves the mail in the queue forever. Our mail queue fills up with garbage Is there any way I can get sendmail to discard messages that have been rejected by the next virtusertable hop (i.e. after step 1 in the Problem description)? Or does anyone have any other solutions to this?

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• Notify user of message arrival in another mailbox

  - by Tim Alexander

  This is very similar to this question but has a few differences. Basically we have a user dealing with a conflict of interest case. To separate the mail from prying eyes (and the draconian routing system we have in place) the user has been granted access to a second conflicts mailbox that is only accessible to him via OWA. This has worked fine for years but now the user would like a notification to be sent to him when a message arrives in his conflicts mailbox. Initially I thought an Outlook rule would work but of course the client is never logged in so the Outlook rules are never processed. This led me to think that an Exchange Transport rule might work but the only options I can see are to Forward or Copy the message to another user. this would bypass the conflicts setup. All I really need is a notification and not the actual message to be sent. Is this at all possible with Exchange 2007? Or if not is there any thirdparty addition or workaround that anyone has come across?

  Read the article

• how to get ip address of a PPP(Point-to-Point Protocol) network interface?

  - by Xsmael

  I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

  Read the article

• Use both OpenVPN & eth0 together

  - by shadyabhi

  I connect to a VPN using openVPN. Now, after the connection is established, all my traffic goes through tun0. My LAN gateway is 10.100.98.4... So, for apps to use my direct internet connnection I did sudo route add default gw 10.100.98.4 But, I cant use tun0 now. I know this because curl --interface tun0 google.com doesnt give me anything.. How do I go about using both connections simultaneously. How can I achieve that? ROUTING TABLES:- Without VPN running:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 With VPN:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0 After the route command- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0

  Read the article

< Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >