Search Results

Search found 6636 results on 266 pages for 'jdbc driver'.

Page 259/266 | < Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >

• Upgrading Windows 8 boot to VHD to Windows 8.1&ndash;Step by step guide

  - by Liam Westley

  Originally posted on: http://geekswithblogs.net/twickers/archive/2013/10/19/upgrading-windows-8-boot-to-vhd-to-windows-8.1ndashstep-by.aspxBoot to VHD – dual booting Windows 7 and Windows 8 became easy When Windows 8 arrived, quite a few people decided that they would still dual boot their machines, and instead of mucking about with resizing disk partitions to free up space for Windows 8 they decided to use the boot from VHD feature to create a huge hard disc image into which Windows 8 could be installed.  Scott Hanselman wrote this installation guide, while I myself used the installation guide from Ed Bott of ZD net fame. Boot to VHD is a great solution, it achieves a dual boot, can be backed up easily and had virtually no effect on the original Windows 7 partition. As a developer who has dual booted Windows operating systems for years, hacking boot.ini files, the boot to VHD was a much easier solution. Upgrade to Windows 8.1 – ah, you can’t do that on a virtual disk installation (boot to VHD) Last week the final version of Windows 8.1 arrived, and I went into the Windows Store to upgrade.  Luckily I’m on a fast download service, and use an SSD, because once the upgrade was downloaded and prepared Windows informed that This PC can’t run Windows 8.1, and provided the reason, You can’t install Windows on a virtual drive.  You can see an image of the message and discussion that sparked my search for a solution in this Microsoft Technet forum post. I was determined not to have to resize partitions yet again and fiddle with VHD to disk utilities and back again, and in the end I did succeed in upgrading to a Windows 8.1 boot to VHD partition.  It takes quite a bit of effort though … tldr; Simple steps of how you upgrade Boot into Windows 7 – make a copy of your Windows 8 VHD, to become Windows 8.1 Enable Hyper-V in your Windows 8 (the original boot to VHD partition) Create a new virtual machine, attaching the copy of your Windows 8 VHD Start the virtual machine, upgrade it via the Windows Store to Windows 8.1 Shutdown the virtual machine Boot into Windows 7 – use the bcedit tool to create a new Windows 8.1 boot to VHD option (pointing at the copy) Boot into the new Windows 8.1 option Reactivate Windows 8.1 (it will have become deactivated by running under Hyper-V) Remove the original Windows 8 VHD, and in Windows 7 use bcedit to remove it from the boot menu Things you’ll need A system that can run Hyper-V under Windows 8 (Intel i5, i7 class CPU) Enough space to have your original Windows 8 boot to VHD and a copy at the same time An ISO or DVD for Windows 8 to create a bootable Windows 8 partition Step by step guide Boot to your base o/s, the real one, Windows 7. Make a copy of the Windows 8 VHD file that you use to boot Windows 8 (via boot from VHD) – I copied it from a folder on C: called VHD-Win8 to VHD-Win8.1 on my N: drive. Reboot your system into Windows 8, and enable Hyper-V if not already present (this may require reboot) Use the Hyper-V manager , create a new Hyper-V machine, using half your system memory, and use the option to attach an existing VHD on the main IDE controller – this will be the new copy you made in Step 2. Start the virtual machine, use Connect to view it, and you’ll probably discover it cannot boot as there is no boot record If this is the case, go to Hyper-V manager, edit the Settings for the virtual machine to attach an ISO of a Windows 8 DVD to the second IDE controller. Start the virtual machine, use Connect to view it, and it should now attempt a fresh installation of Windows 8.  You should select Advanced Options and choose Repair - this will make VHD bootable When the setup reboots your virtual machine, turn off the virtual machine, and remove the ISO of the Windows 8 DVD from the virtual machine settings. Start virtual machine, use Connect to view it.  You will see the devices to be re-discovered (including your quad CPU becoming single CPU).  Eventually you should see the Windows Login screen. You may notice that your desktop background (Win+D) will have turned black as your Windows installation has become deactivate due to the hardware changes between your real PC and Hyper-V. Fortunately becoming deactivated, does not stop you using the Windows Store, where you can select the update to Windows 8.1. You can now watch the progress joy of the Windows 8 update; downloading, preparing to update, checking compatibility, gathering info, preparing to restart, and finally, confirm restart - remember that you are restarting your virtual machine sitting on the copy of the VHD, not the Windows 8 boot to VHD you are currently using to run Hyper-V (confused yet?) After the reboot you get the real upgrade messages; setting up x%, xx%, (quite slow) After a while, Getting ready Applying PC Settings x%, xx% (really slow) Updating your system (fast) Setting up a few more things x%, (quite slow) Getting ready, again Accept license terms Express settings Confirmed previous password Next, I had to set up a Microsoft account – which is possibly now required, and not optional Using the Microsoft account required a 2 factor authorization, via text message, a 7 digit code for me Finalising settings Blank screen, HI .. We're setting up things for you (similar to original Windows 8 install) 'You can get new apps from the Store', below which is ’Installing your apps’ - I had Windows Media Center which is counts as an app from the Store ‘Taking care of a few things’, below which is ‘Installing your apps’ ‘Taking care of a few things’, below ‘Don't turn off your PC’ ‘Getting your apps ready’, below ‘Don't turn off your PC’ ‘Almost ready’, below ‘Don't turn off your PC’ … finally, we get the Windows 8.1 start menu, and a quick Win+D to check the desktop confirmed all the application icons I expected, pinned items on the taskbar, and one app moaning about a missing drive At this point the upgrade is complete – you can shutdown the virtual machine Reboot from the original Windows 8 and return to Windows 7 to configure booting to the Windows 8.1 copy of the VHD In an administrator command prompt do following use the bcdedit tool (from an MSDN blog about configuring VHD to boot in Windows 7) Type bcedit to list the current boot options, so you can copy the GUID (complete with brackets/braces) for the original Windows 8 boot to VHD Create a new menu option, copy of the Windows 8 option; bcdedit /copy {originalguid} /d "Windows 8.1" Point the new Windows 8.1 option to the copy of the VHD; bcdedit /set {newguid} device vhd=[D:]\Image.vhd Point the new Windows 8.1 option to the copy of the VHD; bcdedit /set {newguid} osdevice vhd=[D:]\Image.vhd Set autodetection of the HAL (may already be set); bcdedit /set {newguid} detecthal on Reboot from Windows 7 and select the new option 'Windows 8.1' on the boot menu, and you’ll have some messages to look at, as your hardware is redetected (as you are back from 1 CPU to 4 CPUs) ‘Getting devices ready, blank then %xx, with occasional blank screen, for the graphics driver, (fast-ish) Getting Ready message (fast) You will have to suffer one final reboots, choose 'Windows 8.1' and you can now login to a lovely Windows 8.1 start screen running on non virtualized hardware via boot to VHD After checking everything is running fine, you can now choose to Activate Windows, which for me was a toll free phone call to the automated system where you type in lots of numbers to be given a whole bunch of new activation codes. Once you’re happy with your new Windows 8.1 boot to VHD, and no longer need the Windows 8 boot to VHD, feel free to delete the old one.  I do believe once you upgrade, you are no longer licensed to use it anyway. There, that was simple wasn’t it? Looking at the huge list of steps it took to perform this upgrade, you may wonder whether I think this is worth it.  Well, I think it is worth booting to VHD.  It makes backups a snap (go to Windows 7, copy the VHD, you backed up the o/s) and helps with disk management – want to move the o/s, you can move the VHD and repoint the boot menu to the new location. The downside is that Microsoft has complete neglected to support boot to VHD as an upgradable option.  Quite a poor decision in my opinion, and if you read twitter and the forums quite a few people agree with that view.  It’s a shame this got missed in the work on creating the upgrade packages for Windows 8.1.

  Read the article

• Understanding 400 Bad Request Exception

  - by imran_ku07

      Introduction:          Why I am getting this exception? What is the cause of this error. Developers are always curious to know the root cause of an exception, even though they found the solution from elsewhere. So what is the reason of this exception (400 Bad Request).The answer is security. Security is an important feature for any application. ASP.NET try to his best to give you more secure application environment as possible. One important security feature is related to URLs. Because there are various ways a hacker can try to access server resource. Therefore it is important to make your application as secure as possible. Fortunately, ASP.NET provides this security by throwing an exception of Bad Request whenever he feels. In this Article I am try to present when ASP.NET feels to throw this exception. You will also see some new ASP.NET 4 features which gives developers some control on this situation.   Description:   http.sys Restrictions:           It is interesting to note that after deploying your application on windows server that runs IIS 6 or higher, the first receptionist of HTTP request is the kernel mode HTTP driver: http.sys. Therefore for completing your request successfully you need to present your validity to http.sys and must pass the http.sys restriction.           Every http request URL must not contain any character from ASCII range of 0x00 to 0x1F, because they are not printable. These characters are invalid because these are invalid URL characters as defined in RFC 2396 of the IETF. But a question may arise that how it is possible to send unprintable character. The answer is that when you send your request from your application in binary format.           Another restriction is on the size of the request. A request containg protocal, server name, headers, query string information and individual headers sent along with the request must not exceed 16KB. Also individual header should not exceed 16KB.           Any individual path segment (the portion of the URL that does not include protocol, server name, and query string, for example, http://a/b/c?d=e,  here the b and c are individual path) must not contain more than 260 characters. Also http.sys disallows URLs that have more than 255 path segments.           If any of the above rules are not follow then you will get 400 Bad Request Exception. The reason for this restriction is due to hack attacks against web servers involve encoding the URL with different character representations.           You can change the default behavior enforced by http.sys using some Registry switches present at HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HTTP\Parameters    ASP.NET Restrictions:           After passing the restrictions enforced by the kernel mode http.sys then the request is handed off to IIS and then to ASP.NET engine and then again request has to pass some restriction from ASP.NET in order to complete it successfully.           ASP.NET only allows URL path lengths to 260 characters(only paths, for example http://a/b/c/d, here path is from a to d). This means that if you have long paths containing 261 characters then you will get the Bad Request exception. This is due to NTFS file-path limit.           Another restriction is that which characters can be used in URL path portion.You can use any characters except some characters because they are called invalid characters in path. Here are some of these invalid character in the path portion of a URL, <,>,*,%,&,:,\,?. For confirming this just right click on your Solution Explorer and Add New Folder and name this File to any of the above character, you will get the message. Files or folders cannot be empty strings nor they contain only '.' or have any of the following characters.....            For checking the above situation i have created a Web Application and put Default.aspx inside A%A folder (created from windows explorer), then navigate to, http://localhost:1234/A%25A/Default.aspx, what i get response from server is the Bad Request exception. The reason is that %25 is the % character which is invalid URL path character in ASP.NET. However you can use these characters in query string.           The reason for these restrictions are due to security, for example with the help of % you can double encode the URL path portion and : is used to get some specific resource from server.   New ASP.NET 4 Features:           It is worth to discuss the new ASP.NET 4 features that provides some control in the hand of developer. Previously we are restricted to 260 characters path length and restricted to not use some of characters, means these characters cannot become the part of the URL path segment.           You can configure maxRequestPathLength and maxQueryStringLength to allow longer or shorter paths and query strings. You can also customize set of invalid character using requestPathInvalidChars, under httpruntime element. This may be the good news for someone who needs to use some above character in their application which was invalid in previous versions. You can find further detail about new ASP.NET features about URL at here           Note that the above new ASP.NET settings will not effect http.sys. This means that you have pass the restriction of http.sys before ASP.NET ever come in to the action. Note also that previous restriction of http.sys is applied on individual path and maxRequestPathLength is applied on the complete path (the portion of the URL that does not include protocol, server name, and query string). For example, if URL is http://a/b/c/d?e=f, then maxRequestPathLength will takes, a/b/c/d, into account while http.sys will take a, b, c individually.   Summary:           Hopefully this will helps you to know how some of initial security features comes in to play, but i also recommend that you should read (at least first chapter called Initial Phases of a Web Request of) Professional ASP.NET 2.0 Security, Membership, and Role Management by Stefan Schackow. This is really a nice book.

  Read the article

• Monitor your Hard Drive’s Health with Acronis Drive Monitor

  - by Matthew Guay

  Are you worried that your computer’s hard drive could die without any warning?  Here’s how you can keep tabs on it and get the first warning signs of potential problems before you actually lose your critical data. Hard drive failures are one of the most common ways people lose important data from their computers.  As more of our memories and important documents are stored digitally, a hard drive failure can mean the loss of years of work.  Acronis Drive Monitor helps you avert these disasters by warning you at the first signs your hard drive may be having trouble.  It monitors many indicators, including heat, read/write errors, total lifespan, and more. It then notifies you via a taskbar popup or email that problems have been detected.  This early warning lets you know ahead of time that you may need to purchase a new hard drive and migrate your data before it’s too late. Getting Started Head over to the Acronis site to download Drive Monitor (link below).  You’ll need to enter your name and email, and then you can download this free tool. Also, note that the download page may ask if you want to include a trial of their for-pay backup program.  If you wish to simply install the Drive Monitor utility, click Continue without adding. Run the installer when the download is finished.  Follow the prompts and install as normal. Once it’s installed, you can quickly get an overview of your hard drives’ health.  Note that it shows 3 categories: Disk problems, Acronis backup, and Critical Events.  On our computer, we had Seagate DiskWizard, an image backup utility based on Acronis Backup, installed, and Acronis detected it. Drive Monitor stays running in your tray even when the application window is closed.  It will keep monitoring your hard drives, and will alert you if there’s a problem. Find Detailed Information About Your Hard Drives Acronis’ simple interface lets you quickly see an overview of how the drives on your computer are performing.  If you’d like more information, click the link under the description.  Here we see that one of our drives have overheated, so click Show disks to get more information. Now you can select each of your drives and see more information about them.  From the Disk overview tab that opens by default, we see that our drive is being monitored, has been running for a total of 368 days, and that it’s health is good.  However, it is running at 113F, which is over the recommended max of 107F.   The S.M.A.R.T. parameters tab gives us more detailed information about our drive.  Most users wouldn’t know what an accepted value would be, so it also shows the status.  If the value is within the accepted parameters, it will report OK; otherwise, it will show that has a problem in this area. One very interesting piece of information we can see is the total number of Power-On Hours, Start/Stop Count, and Power Cycle Count.  These could be useful indicators to check if you’re considering purchasing a second hand computer.  Simply load this program, and you’ll get a better view of how long it’s been in use. Finally, the Events tab shows each time the program gave a warning.  We can see that our drive, which had been acting flaky already, is routinely overheating even when our other hard drive was running in normal temperature ranges. Monitor Acronis Backups And Critical Errors In addition to monitoring critical stats of your hard drives, Acronis Drive Monitor also keeps up with the status of your backup software and critical events reported by Windows.  You can access these from the front page, or via the links on the left hand sidebar.  If you have any edition of any Acronis Backup product installed, it will show that it was detected.  Note that it can only monitor the backup status of the newest versions of Acronis Backup and True Image. If no Acronis backup software was installed, it will show a warning that the drive may be unprotected and will give you a link to download Acronis backup software.   If you have another backup utility installed that you wish to monitor yourself, click Configure backup monitoring, and then disable monitoring on the drives you’re monitoring yourself. Finally, you can view any detected Critical events from the Critical events tab on the left. Get Emailed When There’s a Problem One of Drive Monitor’s best features is the ability to send you an email whenever there’s a problem.  Since this program can run on any version of Windows, including the Server and Home Server editions, you can use this feature to stay on top of your hard drives’ health even when you’re not nearby.  To set this up, click Options in the top left corner. Select Alerts on the left, and then click the Change settings link to setup your email account. Enter the email address which you wish to receive alerts, and a name for the program.  Then, enter the outgoing mail server settings for your email.  If you have a Gmail account, enter the following information: Outgoing mail server (SMTP): smtp.gmail.com Port: 587 Username and Password: Your gmail address and password Check the Use encryption box, and then select TLS from the encryption options.   It will now send a test message to your email account, so check and make sure it sent ok. Now you can choose to have the program automatically email you when warnings and critical alerts appear, and also to have it send regular disk status reports.   Conclusion Whether you’ve got a brand new hard drive or one that’s seen better days, knowing the real health of your it is one of the best ways to be prepared before disaster strikes.  It’s no substitute for regular backups, but can help you avert problems.  Acronis Drive Monitor is a nice tool for this, and although we wish it wasn’t so centered around their backup offerings, we still found it a nice tool. Link Download Acronis Drive Monitor (registration required) Similar Articles Productive Geek Tips Quick Tip: Change Monitor Timeout From Command LineAnalyze and Manage Hard Drive Space with WinDirStatMonitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersDefrag Multiple Hard Drives At Once In WindowsFind Your Missing USB Drive on Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows 7’s WordPad is Actually Good Greate Image Viewing and Management with Zoner Photo Studio Free Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer

  Read the article

• Regression testing with Selenium GRID

  - by Ben Adderson

  A lot of software teams out there are tasked with supporting and maintaining systems that have grown organically over time, and the web team here at Red Gate is no exception. We're about to embark on our first significant refactoring endeavour for some time, and as such its clearly paramount that the code be tested thoroughly for regressions. Unfortunately we currently find ourselves with a codebase that isn't very testable - the three layers (database, business logic and UI) are currently tightly coupled. This leaves us with the unfortunate problem that, in order to confidently refactor the code, we need unit tests. But in order to write unit tests, we need to refactor the code :S To try and ease the initial pain of decoupling these layers, I've been looking into the idea of using UI automation to provide a sort of system-level regression test suite. The idea being that these tests can help us identify regressions whilst we work towards a more testable codebase, at which point the more traditional combination of unit and integration tests can take over. Ending up with a strong battery of UI tests is also a nice bonus :) Following on from my previous posts (here, here and here) I knew I wanted to use Selenium. I also figured that this would be a good excuse to put my xUnit [Browser] attribute to good use. Pretty quickly, I had a raft of tests that looked like the following (this particular example uses Reflector Pro). In a nut shell the test traverses our shopping cart and, for a particular combination of number of users and months of support, checks that the price calculations all come up with the correct values. [BrowserTheory] [Browser(Browsers.Firefox3_6, "http://www.red-gate.com")] public void Purchase1UserLicenceNoSupport(SeleniumProvider seleniumProvider) {     //Arrange     _browser = seleniumProvider.GetBrowser();     _browser.Open("http://www.red-gate.com/dynamic/shoppingCart/ProductOption.aspx?Product=ReflectorPro");                  //Act     _browser = ShoppingCartHelpers.TraverseShoppingCart(_browser, 1, 0, ".NET Reflector Pro");     //Assert     var priceResult = PriceHelpers.GetNewPurchasePrice(db, "ReflectorPro", 1, 0, Currencies.Euros);         Assert.Equal(priceResult.Price, _browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl01_Price"));     Assert.Equal(priceResult.Tax, _browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl02_Tax"));     Assert.Equal(priceResult.Total, _browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl02_Total")); } These tests are pretty concise, with much of the common code in the TraverseShoppingCart() and GetNewPurchasePrice() methods. The (inevitable) problem arose when it came to execute these tests en masse. Selenium is a very slick tool, but it can't mask the fact that UI automation is very slow. To give you an idea, the set of cases that covers all of our products, for all combinations of users and support, came to 372 tests (for now only considering purchases in dollars). In the world of automated integration tests, that's a very manageable number. For unit tests, it's a trifle. However for UI automation, those 372 tests were taking just over two hours to run. Two hours may not sound like a lot, but those cases only cover one of the three currencies we deal with, and only one of the many different ways our systems can be asked to calculate a price. It was already pretty clear at this point that in order for this approach to be viable, I was going to have to find a way to speed things up. Up to this point I had been using Selenium Remote Control to automate Firefox, as this was the approach I had used previously and it had worked well. Fortunately,  the guys at SeleniumHQ also maintain a tool for executing multiple Selenium RC tests in parallel: Selenium Grid. Selenium Grid uses a central 'hub' to handle allocation of Selenium tests to individual RCs. The Remote Controls simply register themselves with the hub when they start, and then wait to be assigned work. The (for me) really clever part is that, as far as the client driver library is concerned, the grid hub looks exactly the same as a vanilla remote control. To create a new browser session against Selenium RC, the following C# code suffices: new DefaultSelenium("localhost", 4444, "*firefox", "http://www.red-gate.com"); This assumes that the RC is running on the local machine, and is listening on port 4444 (the default). Assuming the hub is running on your local machine, then to create a browser session in Selenium Grid, via the hub rather than directly against the control, the code is exactly the same! Behind the scenes, the hub will take this request and hand it off to one of the registered RCs that provides the "*firefox" execution environment. It will then pass all communications back and forth between the test runner and the remote control transparently. This makes running existing RC tests on a Selenium Grid a piece of cake, as the developers intended. For a more detailed description of exactly how Selenium Grid works, see this page. Once I had a test environment capable of running multiple tests in parallel, I needed a test runner capable of doing the same. Unfortunately, this does not currently exist for xUnit (boo!). MbUnit on the other hand, has the concept of concurrent execution baked right into the framework. So after swapping out my assembly references, and fixing up the resulting mismatches in assertions, my example test now looks like this: [Test] public void Purchase1UserLicenceNoSupport() {    //Arrange    ISelenium browser = BrowserHelpers.GetBrowser();    var db = DbHelpers.GetWebsiteDBDataContext();    browser.Start();    browser.Open("http://www.red-gate.com/dynamic/shoppingCart/ProductOption.aspx?Product=ReflectorPro");                 //Act     browser = ShoppingCartHelpers.TraverseShoppingCart(browser, 1, 0, ".NET Reflector Pro");    var priceResult = PriceHelpers.GetNewPurchasePrice(db, "ReflectorPro", 1, 0, Currencies.Euros);    //Assert     Assert.AreEqual(priceResult.Price, browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl01_Price"));     Assert.AreEqual(priceResult.Tax, browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl02_Tax"));     Assert.AreEqual(priceResult.Total, browser.GetText("ctl00_content_InvoiceShoppingItemRepeater_ctl02_Total")); } This is pretty much the same as the xUnit version. The exceptions are that the attributes have changed,  the //Arrange phase now has to handle setting up the ISelenium object, as the attribute that previously did this has gone away, and the test now sets up its own database connection. Previously I was using a shared database connection, but this approach becomes more complicated when tests are being executed concurrently. To avoid complexity each test has its own connection, which it is responsible for closing. For the sake of readability, I snipped out the code that closes the browser session and the db connection at the end of the test. With all that done, there was only one more step required before the tests would execute concurrently. It is necessary to tell the test runner which tests are eligible to run in parallel, via the [Parallelizable] attribute. This can be done at the test, fixture or assembly level. Since I wanted to run all tests concurrently, I marked mine at the assembly level in the AssemblyInfo.cs using the following: [assembly: DegreeOfParallelism(3)] [assembly: Parallelizable(TestScope.All)] The second attribute marks all tests in the assembly as [Parallelizable], whilst the first tells the test runner how many concurrent threads to use when executing the tests. I set mine to three since I was using 3 RCs in separate VMs. With everything now in place, I fired up the Icarus* test runner that comes with MbUnit. Executing my 372 tests three at a time instead of one at a time reduced the running time from 2 hours 10 minutes, to 55 minutes, that's an improvement of about 58%! I'd like to have seen an improvement of 66%, but I can understand that either inefficiencies in the hub code, my test environment or the test runner code (or some combination of all three most likely) contributes to a slightly diminished improvement. That said, I'd love to hear about any experience you have in upping this efficiency. Ultimately though, it was a saving that was most definitely worth having. It makes regression testing via UI automation a far more plausible prospect. The other obvious point to make is that this approach scales far better than executing tests serially. So if ever we need to improve performance, we just register additional RC's with the hub, and up the DegreeOfParallelism. *This was just my personal preference for a GUI runner. The MbUnit/Gallio installer also provides a command line runner, a TestDriven.net runner, and a Resharper 4.5 runner. For now at least, Resharper 5 isn't supported.

  Read the article

• What's up with LDoms: Part 4 - Virtual Networking Explained

  - by Stefan Hinker

  I'm back from my summer break (and some pressing business that kept me away from this), ready to continue with Oracle VM Server for SPARC ;-) In this article, we'll have a closer look at virtual networking.  Basic connectivity as we've seen it in the first, simple example, is easy enough.  But there are numerous options for the virtual switches and virtual network ports, which we will discuss in more detail now.   In this section, we will concentrate on virtual networking - the capabilities of virtual switches and virtual network ports - only.  Other options involving hardware assignment or redundancy will be covered in separate sections later on. There are two basic components involved in virtual networking for LDoms: Virtual switches and virtual network devices.  The virtual switch should be seen just like a real ethernet switch.  It "runs" in the service domain and moves ethernet packets back and forth.  A virtual network device is plumbed in the guest domain.  It corresponds to a physical network device in the real world.  There, you'd be plugging a cable into the network port, and plug the other end of that cable into a switch.  In the virtual world, you do the same:  You create a virtual network device for your guest and connect it to a virtual switch in a service domain.  The result works just like in the physical world, the network device sends and receives ethernet packets, and the switch does all those things ethernet switches tend to do. If you look at the reference manual of Oracle VM Server for SPARC, there are numerous options for virtual switches and network devices.  Don't be confused, it's rather straight forward, really.  Let's start with the simple case, and work our way to some more sophisticated options later on.  In many cases, you'll want to have several guests that communicate with the outside world on the same ethernet segment.  In the real world, you'd connect each of these systems to the same ethernet switch.  So, let's do the same thing in the virtual world: root@sun # ldm add-vsw net-dev=nxge2 admin-vsw primary root@sun # ldm add-vnet admin-net admin-vsw mars root@sun # ldm add-vnet admin-net admin-vsw venus We've just created a virtual switch called "admin-vsw" and connected it to the physical device nxge2.  In the physical world, we'd have powered up our ethernet switch and installed a cable between it and our big enterprise datacenter switch.  We then created a virtual network interface for each one of the two guest systems "mars" and "venus" and connected both to that virtual switch.  They can now communicate with each other and with any system reachable via nxge2.  If primary were running Solaris 10, communication with the guests would not be possible.  This is different with Solaris 11, please see the Admin Guide for details.  Note that I've given both the vswitch and the vnet devices some sensible names, something I always recommend. Unless told otherwise, the LDoms Manager software will automatically assign MAC addresses to all network elements that need one.  It will also make sure that these MAC addresses are unique and reuse MAC addresses to play nice with all those friendly DHCP servers out there.  However, if we want to do this manually, we can also do that.  (One reason might be firewall rules that work on MAC addresses.)  So let's give mars a manually assigned MAC address: root@sun # ldm set-vnet mac-addr=0:14:4f:f9:c4:13 admin-net mars Within the guest, these virtual network devices have their own device driver.  In Solaris 10, they'd appear as "vnet0".  Solaris 11 would apply it's usual vanity naming scheme.  We can configure these interfaces just like any normal interface, give it an IP-address and configure sophisticated routing rules, just like on bare metal.  In many cases, using Jumbo Frames helps increase throughput performance.  By default, these interfaces will run with the standard ethernet MTU of 1500 bytes.  To change this,  it is usually sufficient to set the desired MTU for the virtual switch.  This will automatically set the same MTU for all vnet devices attached to that switch.  Let's change the MTU size of our admin-vsw from the example above: root@sun # ldm set-vsw mtu=9000 admin-vsw primary Note that that you can set the MTU to any value between 1500 and 16000.  Of course, whatever you set needs to be supported by the physical network, too. Another very common area of network configuration is VLAN tagging. This can be a little confusing - my advise here is to be very clear on what you want, and perhaps draw a little diagram the first few times.  As always, keeping a configuration simple will help avoid errors of all kind.  Nevertheless, VLAN tagging is very usefull to consolidate different networks onto one physical cable.  And as such, this concept needs to be carried over into the virtual world.  Enough of the introduction, here's a little diagram to help in explaining how VLANs work in LDoms: Let's remember that any VLANs not explicitly tagged have the default VLAN ID of 1. In this example, we have a vswitch connected to a physical network that carries untagged traffic (VLAN ID 1) as well as VLANs 11, 22, 33 and 44.  There might also be other VLANs on the wire, but the vswitch will ignore all those packets.  We also have two vnet devices, one for mars and one for venus.  Venus will see traffic from VLANs 33 and 44 only.  For VLAN 44, venus will need to configure a tagged interface "vnet44000".  For VLAN 33, the vswitch will untag all incoming traffic for venus, so that venus will see this as "normal" or untagged ethernet traffic.  This is very useful to simplify guest configuration and also allows venus to perform Jumpstart or AI installations over this network even if the Jumpstart or AI server is connected via VLAN 33.  Mars, on the other hand, has full access to untagged traffic from the outside world, and also to VLANs 11,22 and 33, but not 44.  On the command line, we'd do this like this: root@sun # ldm add-vsw net-dev=nxge2 pvid=1 vid=11,22,33,44 admin-vsw primary root@sun # ldm add-vnet admin-net pvid=1 vid=11,22,33 admin-vsw mars root@sun # ldm add-vnet admin-net pvid=33 vid=44 admin-vsw venus Finally, I'd like to point to a neat little option that will make your live easier in all those cases where configurations tend to change over the live of a guest system.  It's the "id=<somenumber>" option available for both vswitches and vnet devices.  Normally, Solaris in the guest would enumerate network devices sequentially.  However, it has ways of remembering this initial numbering.  This is good in the physical world.  In the virtual world, whenever you unbind (aka power off and disassemble) a guest system, remove and/or add network devices and bind the system again, chances are this numbering will change.  Configuration confusion will follow suit.  To avoid this, nail down the initial numbering by assigning each vnet device it's device-id explicitly: root@sun # ldm add-vnet admin-net id=1 admin-vsw venus Please consult the Admin Guide for details on this, and how to decipher these network ids from Solaris running in the guest. Thanks for reading this far.  Links for further reading are essentially only the Admin Guide and Reference Manual and can be found above.  I hope this is useful and, as always, I welcome any comments.

  Read the article

• WWDC and Tech Ed: A Tale of Two DevCons

  - by andrewbrust

  Next week marks the first full week of June.  Summer will feel in full swing and it will be a pretty big season for technology.  In seeming acknowledgement of that very fact, both Apple and Microsoft will be holding large developers conferences starting Monday.  Apple will hold its annual Worldwide Developers Conference (WWDC) in lovely San Francisco and Microsoft will hold its Tech Ed conference in muggy, oil-laden yet soulful New Orleans.  A brief survey of each show reveals much about the differences in each company’s offerings, strategy, and approach to customers and partners. In the interest of full disclosure, I must explain that I will be speaking at Microsoft’s Tech Ed show, and have done so, on and off, since 2003.  I have never been to an Apple conference and, as readers of this blog may know, I acquired my first ever Apple product 2 months ago when I bought an iPad on the day of that product’s launch.  I think I have keen insights into Microsoft’s conference.  My ability to comment on Apple’s event ranges somewhere between backseat driver and naive observer.  Just so you know. Although both shows cater to their respective company’s developers, there are a number of differences in the events’ purposes and content approaches.  First off, let’s consider each show as a news and PR vehicle.  WWDC will feature Steve Jobs’ keynote address and most likely will be where Apple officially reveals details of its 4th-generation iPhone. Jobs will likely also provide deep background information on the corresponding iPhone OS release.  These presumed announcements will make the show a magnet for the tech press and tech blogger elite.  Apple’s customers will be interested too, especially since the iPhone OS release will likely be made available to owners of existing iPhone, iPod Touch and iPad devices. Tech Ed, on the other hand, may not be especially newsworthy at all.  The keynote address will be given by Bob Muglia, who is President of the company’s Server and Tools Division, and he’ll likely be reviewing things more than previewing them. That’s because the company has, in the last 6-8 months, already released new versions of a majority of its products, including Windows, Office, SharePoint, SQL Server, Exchange, its Azure cloud platform, its .NET software development layer, its Silverlight Rich Internet Application (RIA) technology and its Visual Studio developer suite.  Redmond’s product pipeline has functioned more like a firehose of late, and the company has a ton of work to do to get developers up to speed on everything that’s new. I know I keep saying “developers,” but in Tech Ed’s case, that’s not really accurate.  In North America, Tech Ed caters to both developers and IT pros (i.e. technologists who work with physical IT infrastructure, as well as security and administration of the server software that runs on it).  This pairing has, since its inception, struck some as anomalous and others, including many exhibitors, as very smart. Certainly, it means Tech Ed ends up being a confab for virtually all professionals in Microsoft’s ecosystem.  And this year, Microsoft’s Business Intelligence (BI) conference will be co-located with Tech Ed, further enhancing that fusion effect. Clearly then, Microsoft’s show will focus on education, as its name assures us.  Apple’s will serve as both a press event and an opportunity to get its own App Store developer channel synced up with its newest technology advances.  For example, we already know that iPhone OS 4.0 will provide for a limited multitasking capability; that will only work well if people know how to code to it in a capable way.  Apple also told us its iAd advertising platform will be part of the new OS, and Steve Jobs insists that’s to provide a revenue opportunity for developers.  This too, then, needs to be explicated and soaked up buy the faithful. A look at each show’s breakout session lineup provides some interesting takeaways.  WWDC will have very few Mac-specific sessions on offer, and virtually no sessions that at are IT- or “Enterprise-“ related.  It’s all about the phone, music players and tablets.  However, WWDC will have plenty of low-level, hardcore tech coverage of such things as Advanced Memory Analysis and Creating Secure Applications, as well as lots of rich media-related content like Core Animation and Game Design and Development.  Beyond Apple’s proprietary platform, WWDC will also feature an array of sessions on HTML 5 and other Web standards.  In all, WWDC offers over 100 technical sessions and hands-on labs. What about Tech Ed’s editorial content?  Like the target audience, it really runs the gamut.  The show has 21 tracks (versus WWDC’s 5) and more than 745 “learning opportunities” which include breakout sessions, demo stations, hands-on labs and BIrds of a Feather discussion sessions.  Topics range from Architecture talks like Patterns of Parallel Programming to cloud computing talks like Building High Capacity Compute Applications with Windows Azure to IT-focused topics like Virtualization of Microsoft SharePoint 2010 Farm Architecture.  I also count 19 sessions on Windows Phone 7.  Unfortunately, with regard to Web standards and HTML 5, only a few sessions are offered, all of them specific to Internet Explorer. All-in-all, Apple’s show looks more exciting and “sexier” than Tech Ed. Microsoft’s show seems a lot more enterprise-focused than WWDC. This is, of course, well in sync with each company’s approach and products.  Microsoft’s content is much wider ranging and bests WWDC in sheer volume of sessions and labs.  I suppose some might argue that less is more; others that Apple’s consumer-focused offerings simply don’t provide for the same depth of coverage to a business audience.  Microsoft has a serious focus on the cloud and  a paucity of coverage on client-side Web standards; Apple has virtually no cloud offering at all.  Again, this reflects each tech titan’s go-to-market strategy. My own take is that employees of each company should attend the other’s event.  The amount of mutual exclusivity in content may make sense in terms of corporate philosophy, but the reality is that each company could stand to diversify into the other’s territory, at least somewhat. My own talk at Tech Ed will focus on competitive analysis around Microsoft’s BI products.  Apple does not today figure into that analysis. Maybe one day it will.

  Read the article

• Run Your Tests With Any NUnit Version

  - by Alois Kraus

  I always thought that the NUnit test runners and the test assemblies need to reference the same NUnit.Framework version. I wanted to be able to run my test assemblies with the newest GUI runner (currently 2.5.3). Ok so all I need to do is to reference both NUnit versions the newest one and the official for the current project. There is a nice article form Kent Bogart online how to reference the same assembly multiple times with different versions. The magic works by referencing one NUnit assembly with an alias which does prefix all types inside it. Then I could decorate my tests with the TestFixture and Test attribute from both NUnit versions and everything worked fine except that this was ugly. After playing a little bit around to make it simpler I found that I did not need to reference both NUnit.Framework assemblies. The test runners do not require the TestFixture and Test attribute in their specific version. That is really neat since the test runners are instructed by attributes what to do in a declarative way there is really no need to tie the runners to a specific version. At its core NUnit has this little method hidden to find matching TestFixtures and Tests   public bool CanBuildFrom(Type type) {     if (!(!type.IsAbstract || type.IsSealed))     {         return false;     }     return (((Reflect.HasAttribute(type,           "NUnit.Framework.TestFixtureAttribute", true) ||               Reflect.HasMethodWithAttribute(type, "NUnit.Framework.TestAttribute"       , true)) ||               Reflect.HasMethodWithAttribute(type, "NUnit.Framework.TestCaseAttribute"   , true)) ||               Reflect.HasMethodWithAttribute(type, "NUnit.Framework.TheoryAttribute"     , true)); } That is versioning and backwards compatibility at its best. I tell NUnit what to do by decorating my tests classes with NUnit Attributes and the runner executes my intent without the need to bind me to a specific version. The contract between NUnit versions is actually a bit more complex (think of AssertExceptions) but this is also handled nicely by using not the concrete type but simply to check for the catched exception type by string. What can we learn from this? Versioning can be easy if the contract is small and the users of your library use it in a declarative way (Attributes). Everything beyond it will force you to reference several versions of the same assembly with all its consequences. Type equality is lost between versions so none of your casts will work. That means that you cannot simply use IBigInterface in two versions. You will need a wrapper to call the correct versioned one. To get out of this mess you can use one (and only one) version agnostic driver to encapsulate your business logic from the concrete versions. This is of course more work but as NUnit shows it can be easy. Simplicity is therefore not a nice thing to have but also requirement number one if you intend to make things more complex in version two and want to support any version (older and newer). Any interaction model above easy will not be maintainable. There are different approached to versioning. Below are my own personal observations how versioning works within the  .NET Framwork and NUnit.   Versioning Models 1. Bug Fixing and New Isolated Features When you only need to fix bugs there is no need to break anything. This is especially true when you have a big API surface. Microsoft did this with the .NET Framework 3.0 which did leave the CLR as is but delivered new assemblies for the features WPF, WCF and Windows Workflow Foundations. Their basic model was that the .NET 2.0 assemblies were declared as red assemblies which must not change (well mostly but each change was carefully reviewed to minimize the risk of breaking changes as much as possible) whereas the new green assemblies of .NET 3,3.5 did not have such obligations since they did implement new unrelated features which did not have any impact on the red assemblies. This is versioning strategy aimed at maximum compatibility and the delivery of new unrelated features. If you have a big API surface you should strive hard to do the same or you will break your customers code with every release. 2. New Breaking Features There are times when really new things need to be added to an existing product. The .NET Framework 4.0 did change the CLR in many ways which caused subtle different behavior although the API´s remained largely unchanged. Sometimes it is possible to simply recompile an application to make it work (e.g. changed method signature void Func() –> bool Func()) but behavioral changes need much more thought and cannot be automated. To minimize the impact .NET 2.0,3.0,3.5 applications will not automatically use the .NET 4.0 runtime when installed but they will keep using the “old” one. What is interesting is that a side by side execution model of both CLR versions (2 and 4) within one process is possible. Key to success was total isolation. You will have 2 GCs, 2 JIT compilers, 2 finalizer threads within one process. The two .NET runtimes cannot talk  (except via the usual IPC mechanisms) to each other. Both runtimes share nothing and run independently within the same process. This enables Explorer plugins written for the CLR 2.0 to work even when a CLR 4 plugin is already running inside the Explorer process. The price for isolation is an increased memory footprint because everything is loaded and running two times.   3. New Non Breaking Features It really depends where you break things. NUnit has evolved and many different Assert, Expect… methods have been added. These changes are all localized in the NUnit.Framework assembly which can be easily extended. As long as the test execution contract (TestFixture, Test, AssertException) remains stable it is possible to write test executors which can run tests written for NUnit 10 because the execution contract has not changed. It is possible to write software which executes other components in a version independent way but this is only feasible if the interaction model is relatively simple.   Versioning software is hard and it looks like it will remain hard since you suddenly work in a severely constrained environment when you try to innovate and to keep everything backwards compatible at the same time. These are contradicting goals and do not play well together. The easiest way out of this is to carefully watch what your customers are doing with your software. Minimizing the impact is much easier when you do not need to guess how many people will be broken when this or that is removed.

  Read the article

• Robotic Arm &ndash; Hardware

  - by Szymon Kobalczyk

  This is first in series of articles about project I've been building  in my spare time since last Summer. Actually it all began when I was researching a topic of modeling human motion kinematics in order to create gesture recognition library for Kinect. This ties heavily into motion theory of robotic manipulators so I also glanced at some designs of robotic arms. Somehow I stumbled upon this cool looking open source robotic arm: It was featured on Thingiverse and published by user jjshortcut (Jan-Jaap). Since for some time I got hooked on toying with microcontrollers, robots and other electronics, I decided to give it a try and build it myself. In this post I will describe the hardware build of the arm and in later posts I will be writing about the software to control it. Another reason to build the arm myself was the cost factor. Even small commercial robotic arms are quite expensive – products from Lynxmotion and Dagu look great but both cost around USD $300 (actually there is one cheap arm available but it looks more like a toy to me). In comparison this design is quite cheap. It uses seven hobby grade servos and even the cheapest ones should work fine. The structure is build from a set of laser cut parts connected with few metal spacers (15mm and 47mm) and lots of M3 screws. Other than that you’d only need a microcontroller board to drive the servos. So in total it comes a lot cheaper to build it yourself than buy an of the shelf robotic arm. Oh, and if you don’t like this one there are few more robotic arm projects at Thingiverse (including one by oomlout). Laser cut parts Some time ago I’ve build another robot using laser cut parts so I knew the process already. You can grab the design files in both DXF and EPS format from Thingiverse, and there are also 3D models of each part in STL. Actually the design is split into a second project for the mini servo gripper (there is also a standard servo version available but it won’t fit this arm).  I wanted to make some small adjustments, layout, and add measurements to the parts before sending it for cutting. I’ve looked at some free 2D CAD programs, and finally did all this work using QCad 3 Beta with worked great for me (I also tried LibreCAD but it didn’t work that well). All parts are cut from 4 mm thick material. Because I was worried that acrylic is too fragile and might break, I also ordered another set cut from plywood. In the end I build it from plywood because it was easier to glue (I was told acrylic requires a special glue). Btw. I found a great laser cutter service in Kraków and highly recommend it (www.ebbox.com.pl). It cost me only USD $26 for both sets ($16 acrylic + $10 plywood). Metal parts I bought all the M3 screws and nuts at local hardware store. Make sure to look for nylon lock (nyloc) nuts for the gripper because otherwise it unscrews and comes apart quickly. I couldn’t find local store with metal spacers and had to order them online (you’d need 11 x 47mm and 3 x 15mm). I think I paid less than USD $10 for all metal parts. Servos This arm uses five standards size servos to drive the arm itself, and two micro servos are used on the gripper. Author of the project used Modelcraft RS-2 Servo and Modelcraft ES-05 HT Servo. I had two Futaba S3001 servos laying around, and ordered additional TowerPro SG-5010 standard size servos and TowerPro SG90 micro servos. However it turned out that the SG90 won’t fit in the gripper so I had to replace it with a slightly smaller E-Sky EK2-0508 micro servo. Later it also turned out that Futaba servos make some strange noise while working so I swapped one with TowerPro SG-5010 which has higher torque (8kg / cm). I’ve also bought three servo extension cables. All servos cost me USD $45. Assembly The build process is not difficult but you need to think carefully about order of assembling it. You can do the base and upper arm first. Because two servos in the base are close together you need to put first with one piece of lower arm already connected before you put the second servo. Then you connect the upper arm and finally put the second piece of lower arm to hold it together. Gripper and base require some gluing so think it through too. Make sure to look closely at all the photos on Thingiverse (also other people copies) and read additional posts on jjshortcust’s blog: My mini servo grippers and completed robotic arm  Multiply the robotic arm and electronics Here is also Rob’s copy cut from aluminum My assembled arm looks like this – I think it turned out really nice: Servo controller board The last piece of hardware I needed was an electronic board that would take command from PC and drive all seven servos. I could probably use Arduino for this task, and in fact there are several Arduino servo shields available (for example from Adafruit or Renbotics).  However one problem is that most support only up to six servos, and second that their accuracy is limited by Arduino’s timer frequency. So instead I looked for dedicated servo controller and found a series of Maestro boards from Pololu. I picked the Pololu Mini Maestro 12-Channel USB Servo Controller. It has many nice features including native USB connection, high resolution pulses (0.25µs) with no jitter, built-in speed and acceleration control, and even scripting capability. Another cool feature is that besides servo control, each channel can be configured as either general input or output. So far I’m using seven channels so I still have five available to connect some sensors (for example distance sensor mounted on gripper might be useful). And last but important factor was that they have SDK in .NET – what more I could wish for! The board itself is very small – half of the size of Tic-Tac box. I picked one for about USD $35 in this store. Perhaps another good alternative would be the Phidgets Advanced Servo 8-Motor – but it is significantly more expensive at USD $87.30. The Maestro Controller Driver and Software package includes Maestro Control Center program with lets you immediately configure the board. For each servo I first figured out their move range and set the min/max limits. I played with setting the speed an acceleration values as well. Big issue for me was that there are two servos that control position of lower arm (shoulder joint), and both have to be moved at the same time. This is where the scripting feature of Pololu board turned out very helpful. I wrote a script that synchronizes position of second servo with first one – so now I only need to move one servo and other will follow automatically. This turned out tricky because I couldn’t find simple offset mapping of the move range for each servo – I had to divide it into several sub-ranges and map each individually. The scripting language is bit assembler-like but gets the job done. And there is even a runtime debugging and stack view available. Altogether I’m very happy with the Pololu Mini Maestro Servo Controller, and with this final piece I completed the build and was able to move my arm from the Meastro Control program.   The total cost of my robotic arm was: $10 laser cut parts $10 metal parts $45 servos $35 servo controller ----------------------- $100 total So here you have all the information about the hardware. In next post I’ll start talking about the software that I wrote in Microsoft Robotics Developer Studio 4. Stay tuned!

  Read the article

• OTN ???? ?????? ???????

  - by Yusuke.Yamamoto

  Database ?? Database ??????? Database ?????????? Java WebLogic Server/????????·???? SOA/BPM/????? ???????/???? ID??/?????? ?????EPM/BI EPM/BI ??????? EPM/BI ???? OS/??? ???? ????? MySQL Database ?? ???? ?? ????????? ??? ?? ORACLE MASTER??Master??ORACLE MASTER Bronze?Bronze DBA11g? ??(WMV)??(MP4)2011/6/22 ORACLE MASTER??Master??ORACLE MASTER Bronze?11g SQL??????(WMV)??(MP4)2011/3/9 ORACLE MASTER??Master??ORACLE MASTER Silver?Silver DBA11g???(WMV)??(MP4)2010/3/2 ORACLE MASTER??Master??ORACLE MASTER Silver?Silver DBA11g?[10g-11g???] ??(WMV)??(MP4)2012/4/23 ORACLE MASTER??Master??ORACLE MASTER Gold DBA11g ??(WMV)??(MP4)2011/2/23 ORACLE MASTER??Master??ORACLE MASTER Gold ?Gold DBA11g ????[??]??(WMV)??(MP4)2012/4/23 ORACLE MASTER??Master??30?????? ORACLE MASTER??????(WMV)??(MP4)2012/9/3 Oracle Database???????????????!Oracle??????????!???(WMV)??(MP4)2010/9/8 Oracle Database???????????????????!? Oracle?? ?????(WMV)??(MP4)2011/4/13 Oracle Database???????????????????!? Oracle?? ??????????(WMV)??(MP4)2011/4/20 Oracle Database???????????????????????????!? ??????????-?????(WMV)??(MP4)2012/2/20 Oracle Database???????????????????????????!? ??????????-?????(WMV)??(MP4)2012/2/20 Oracle Database????????????60???????!?????????????·???????? ??(WMV)??(MP4)2011/5/17 Oracle Database???Step by Step?????!? Oracle Database 11g -?????????-??(WMV)??(MP4)2009/12/17 Oracle Database???Step by Step?????!? OracleDatabase11g -???????????(WMV)??(MP4)2009/12/24 Oracle Database???Step by Step?????!? Oracle Database 11g -?????????(WMV)??(MP4)2009/12/10 Oracle Database DBA?????????????????!???????????(WMV)??(MP4)2010/12/21 Oracle Database DBA?????????????????!????????·??????????(WMV)??(MP4)2010/11/16 Oracle Database DBA?????????????????!???????·????????(WMV)??(MP4)2010/12/15 Oracle Database DBA?????????????????!???????????(WMV)??(MP4)2010/7/21 Oracle Database DBA?????????????????!?Export/Import?????(WMV)??(MP4)2010/9/8 Oracle Database DBA??????????????????!??????????????(WMV)??(MP4)2011/7/20 Oracle Database DBA?????????·????????!!????????!?????????SQL????????(WMV)??(MP4)2010/11/24 Oracle Database DBA?????????·?????????SQL????????????!SQL????????(WMV)??(MP4)2012/1/23 Oracle Database DBA?????????·????????!!???????·??????~DiskI/O?????????~??(WMV)??(MP4)2011/3/9 Oracle Database DBA?????????·????????!!???????·??????~SQL???????~??(WMV)??(MP4)2011/9/20 Oracle Database DBA?????????·????????!???????·??????-Statspack??-??(WMV)??(MP4)2010/7/28 Oracle Database DBA?????????·????????!!???????·??????~??????????~??(WMV)??(MP4)2010/8/4 Oracle Database DBA?????????·????????!!???????·??????-?????????-??(WMV)??(MP4)2010/7/14 Oracle Database DBA?????????·?????? ??!????????????? ??????(WMV)??(MP4)2010/7/7 Oracle Database DBA?????????·????????!????????????? ??????(WMV)??(MP4)2010/7/7 Oracle Database DBA?????????·????????!! ????????DB ??????Tips??(WMV)??(MP4)2010/8/5 Oracle Database DBA??????????!!??????~Oracle Database???~??(WMV)??(MP4)2010/8/31 Oracle Database DBA??????????!!??????~OracleDatabase????~??(WMV)??(MP4)2010/8/24 Oracle Database DBA???????????????????????????????????????(WMV)??(MP4)2010/4/27 Oracle Database DBA????????&?????????????·???? - ?????RMAN??????(WMV)??(MP4)2010/10/13 Oracle Database DBA????????&???????!!??????·????-???????????-??(WMV)??(MP4)2010/9/8 Oracle Database DBA????????&???????!??????·???? ~?????? VS RMAN ?????????~??(WMV)??(MP4)2012/1/23 Oracle Database DBA????????&???????!??????·???? ~????????????~??(WMV)??(MP4)2011/7/27 Oracle Database DBA????????&?????????????????-???????????????????(WMV)??(MP4)2010/10/6 Oracle Database Developer??????????????? Oracle SQL????(WMV)??(MP4)2010/10/20 Oracle Database Developer??????????????? Oracle PL/SQL????(WMV)??(MP4)2012/1/23 Oracle Database Developer????????!!PL/SQL????????(WMV)??(MP4)2011/03 Oracle Database Developer?????????????????????(WMV)??(MP4)2011/5/25 Oracle Database Developer??Java??java???!??(WMV)??(MP4)2009/11/26 Database ??????? ???? ?? ????????? ??? ?? DB???????????????!Oracle Database????????(WMV)??(MP4)2010/5/12 DB???????????????????? Oracle Enterprise Manager??(WMV)??(MP4)2012/1/23 DB??????????!Oracle Enterprise Manager???????????????? ??(WMV)??(MP4)2012/1/23 DB??????????!Oracle Enterprise Manager??????????????·?????? ??(WMV)??(MP4)2012/1/23 DB?????????????(UX)????????????????????(WMV)??(MP4)2011/4/6 DB???????????????????????????????Oracle Enterprise Manager??????!??(WMV)??(MP4)2012/1/23 DB???JP1??????????????????????!JP1???????????(WMV)??(MP4)2011/6/9 DB???JP1JP1???????!DB????????·??????!??(WMV)??(MP4)2011/1/12 DB???SAP"SAP on Oracle Database"???Tips??(WMV)??(MP4)2011/1/12 DB?????????????????! Oracle Database ????????(WMV)??(MP4)2012/1/23 DB?????????Web????????? ~????????~??(WMV)??(MP4)2010/3/10 DB?????????Web??????? ~????????????????????????~??(WMV)??(MP4)2010/2/3 DB??????????Oracle Database Upgrade?????(WMV)??(MP4)2011/9/20 DB??????????Oracle Database Client??????????????(WMV)??(MP4)2011/4/26 DB??????????Oracle Database 11g Release 2????????????????? ??(WMV)??(MP4)2012/1/23 DB?????????????!Oracle???????????????????????????(WMV)??(MP4)2011/1/18 DB???PL/SQLPL/SQL??????? ????(WMV)??(MP4)2012/1/23 DB???PL/SQLPL/SQL??????? ????(WMV)??(MP4)2012/1/23 DB???SQL DeveloperOracle SQL Developer????????????????(WMV)??(MP4)2012/1/23 DB???Jdeveloper??IDE Oracle JDeveloper??????????????????(WMV)??(MP4)2012/1/23 DB???APEX?????????!!APEX??????????????(WMV)??(MP4)2011/4/13 DB???APEX????!60??????Web??????????(WMV)??(MP4)2011/3/3 DB???APEXOracle??????????????! APEX4.0??????(WMV)??(MP4)2011/2/9 DB???APEX?????!????????!Oracle APEX???????????(WMV)??(MP4)2011/6/23 DB???Large Object??·???????DB????? -LOB???????-??(WMV)??(MP4)2010/2/4 DB???XMLOracle Database???????XML???????(WMV)??(MP4)2011/3/16 DB???XML??????XML?? - ?????! XML??? -??(WMV)??(MP4)2010/8/18 DB???XML??????XML?? - Oracle????XML -??(WMV)??(MP4)2010/8/25 DB???????SQL?????!Oracle Database????????Oracle Text???????(WMV)??(MP4) - DB???Oracle Data Guard??!Oracle Data Guard ????????????????????(WMV)??(MP4)2012/1/23 DB???Oracle Real Application Clusters??!?????????? ~RAC???~??(WMV)??(MP4)2012/1/23 DB???Oracle Real Application Clusters??!?????????? ~RAC??? ~??(WMV)??(MP4)2012/1/23 DB???Oracle Real Application Clusters??!Oracle RAC????????????????????????(WMV)??(MP4)2012/1/23 DB???Oracle Real Application Clusters??????!RAC????????????(WMV)??(MP4)2012/1/23 DB???Oracle Real Application Clusters?????????????!!60?????RAC????(WMV)??(MP4)2010/12/8 DB???????????????????????????!!?Oracle Database Firewall? ??(WMV)??(MP4)2012/1/23 DB?????????Oracle Database Firewall??????????? ??(WMV)??(MP4)2012/5/14 DB?????????????????????????????????????????(WMV)??(MP4)2011/5/11 DB??????????????????????????????????????(WMV)??(MP4)2011/4/19 DB????????????????! ???????????????(WMV)??(MP4)2012/1/23 DB?????????????????????????????????(WMV)??(MP4)2010/11/16 DB???????????????????????????????????????????????(WMV)??(MP4)2011/2/9 DB???????????????~???????~??(WMV)??(MP4)2010/12/22 DB???????????????~????/????????~??(WMV)??(MP4)2011/5/24 DB??????Oracle VM 3.0 ???????(WMV)??(MP4)2011/10/3 DB??????????????BCP/BCM???Oracle??????????(WMV)??(MP4)2011/7/13 DB???????????????????????????????????????(WMV)??(MP4)2011/7/12 DB????????DB??????????!??????? Oracle ????????????? ??(WMV)??(MP4)2012/1/23 DB??????????????????!?????????????????(WMV)??(MP4)2011/6/22 DB??????????????????????(WMV)??(MP4)2011/10/17 DB???????????????????????????(WMV)??(MP4)2011/10/17 DB????????????????~?????????????????IT????~??(WMV)??(MP4)2009/12/22 DB??????????!???????? ~????????????????~??(WMV)??(MP4)2011/11/1 DB???????????????????? -???????????(WMV)??(MP4)2011/6/21 DB????????20?????? Oracle GoldenGate??(WMV)??(MP4)2012/4/23 DB????????Oracle GoldenGate?????????????(WMV)??(MP4)2012/5/14 DB???????????????????????????!Oracle GoldenGate??????(WMV)??(MP4)2011/11/1 DB???????????????????!GoldenGate????DB?????????(WMV)??(MP4)2011/8/24 DB????????????????????????? Oracle GoldenGate ????????????! ??(WMV)??(MP4)2012/1/23 DB???????? ??????????????????????????????(WMV)??(MP4)2011/03 DB???????????????!! Oracle Data Integrator??????????(WMV)??(MP4)2009/12/17 DB??????????!??????????????????????(WMV)??(MP4)2011/4/6 DB???????????????????????Oracle Database ????? ????(WMV)??(MP4)2012/1/23 DB???????????????????????Oracle Database ????? ????(WMV)??(MP4)2012/1/23 DB????????????!??????·??????????????????(WMV)??(MP4)2012/1/23 DB???Oracle Partitioning??!????????????????? ????(WMV)??(MP4)2012/1/23 DB???Oracle Partitioning??!????????????????? ????(WMV)??(MP4)2012/1/23 DB?????????????????!SQL?????????? ??(WMV)??(MP4)2010/12/21 DB???Exadata20?????? Oracle Exadata??(WMV)??(MP4)2012/4/23 DB???ExadataOracle Exadata??????????????????(WMV)??(MP4)2012/5/14 DB???Exadata????!Oracle Exadata????? ??(WMV)??(MP4)2011/10/17 DB???ExadataOracle Exadata????????????????????????? ??(WMV)??(MP4)2012/1/23 DB?????????DB?????DB????????????????? -Oracle TimesTen ????-??(WMV)??(MP4)2012/1/23 DB?????????DBWeb????????????!????????????????(WMV)??(MP4)2010/11/4 DB????????DBA?"???????" ????????????????(WMV)??(MP4)2010/8/25 DB?????????????!?Oracle ASM??????????????(WMV)??(MP4)2011/7/8 DB????????Oracle ASM ? Oracle Clusterware ??????????? ??(WMV)??(MP4)2012/1/23 DB????????????????????????????????? - Oracle ASM Cluster File System (ACFS)????! ??(WMV)??(MP4)2012/1/23 DB??????????????????/????·????????Flashback Database with SSD???(WMV)??(MP4)2011/10/17 DB???????????????????DB??????~RAC VM with SSD??(WMV)??(MP4)2011/1/11 DB????????Oracle???????????? SSD?????!??(WMV)??(MP4)2010/8/11 DB??????????????NAS??????!Oracle Database?I/O???????NFS????????????SSD?????????????(WMV)??(MP4)2012/1/23 DB????????????! ???????????? ~????·???????????????~??(WMV)??(MP4)2009/3/25 DB??????????!???????????????????(WMV)??(MP4)2011/3/15 DB???????????????????????!??????·?????????(WMV)??(MP4)2010/6/23 Windows/.Net?????????Oracle on Windows-???? OVM,Hyper-V????(WMV)??(MP4)2011/4/13 Windows/.Net????????Windows Server?Oracle?????!??(WMV)??(MP4)2010/5/19 Windows/.Net????????Oracle on Windows - ??????&???? ?????(WMV)??(MP4)2011/4/20 Windows/.Net??????.Net.NET + Oracle Database ??????????????????????(WMV)??(MP4)2012/1/23 Windows/.Net??????.Net.NET????????Oracle Database ??(WMV)??(MP4)2011/1/20 Windows/.Net??????.NetOracle on Windows-.NET+Oracle ???????(WMV)??(MP4)2011/6/28 Windows/.Net??????.NetVB6????.NET? ~DB????????????~??(WMV)??(MP4)2010/8/4 Windows/.Net??????.Net.NET+Oracle ???????????????????(WMV)??(MP4)2011/10/3 Windows/.Net??????Active Directory30????!Active Directory+Oracle??(WMV)??(MP4)2010/9/8 Windows/.Net??????AccessAccess????WEB?????????????????????????(WMV)??(MP4)2011/7/20 Windows/.Net??????Oracle Real Application ClustersWindows?RAC??!????????????(WMV)??(MP4)2010/9/1 Windows/.Net????????????Oracle on Windows ~???????~ ??(WMV)??(MP4)2011/1/18 Windows/.Net????????????Oracle on Windows ~???????~ ??(WMV)??(MP4)2011/1/20 Windows/.Net???????????MSCS????!?Windows+Oracle????????(WMV)??(MP4)2010/8/4 ???????11gR2???????!Oracle DB 11g???????/??????(WMV)??(MP4)2011/4/14 ???????11gR2???! Oracle Database 11g R2 ?????????(WMV)??(MP4)2010/11/17 ???????11gR2DB??????·??????????11g R2?????(WMV)??(MP4)2010/9/15 ????????????????DWH????????????????·??????????(WMV)??(MP4)2010/11/25 ????????????????DWH????????????????·??????????(WMV)??(MP4)2010/11/25 ????????????????DWH????????????????·??????????(WMV)??(MP4)2010/11/25 Database ?????????? ???? ?? ????????? ??? ?? Oracle Master Platinum??Oracle Real Application Clusters?Platinum???????Platinum???!?????? Oracle RAC ?????????(WMV)??(MP4)2010/1/26 Oracle Master Platinum??????????Platinum??????? Platinum???!???????Oracle??????????????(WMV)??(MP4)2010/4/21 Oracle Master Platinum????????Platinum??:?????????????????????(WMV)??(MP4)2010/5/26 Oracle Master Platinum????????·?????Platinum??????? Platinum???! ????????????·?????????(WMV)??(MP4)2010/3/9 ????????????????????????????!?????????&?????????(WMV)??(MP4)2012/1/23 ????????????????????????????!SQL????????? ??? Part1&2??(WMV)??(MP4)2010/10/12 ????????????????????????????!SQL????????? ??? Part3 ??(WMV)??(MP4)2010/10/19 ????????????????????????????!SQL????????? ??? Part4 ??(WMV)??(MP4)2011/1/27 ????????????????????????????!SQL????????? ??? Part5 ??(WMV)??(MP4)2011/1/27 ????????????????????????????!?????????????????????(WMV)??(MP4)2012/1/23 ????????????????????????????!????????? Part1 ??(WMV)??(MP4) - ????????????????????????????!????????? Part2 ??(WMV)??(MP4)2011/7/26 ????????????????????????????!????????? Part3 ??(WMV)??(MP4)2010/4/28 ????????????????????????????!??????? Part1 ??(WMV)??(MP4)2011/11/1 ????????????????????????????????????????? Part2 ??(WMV)??(MP4)2012/5/28 ????????????????????????????!???????????????????????????? ??(WMV)??(MP4)2012/1/23 ??????????????????????????!??????? Part1 ??(WMV)??(MP4)2011/2/10 ??????????????????????????!??????? Part2 ??(WMV)??(MP4)2011/3/23 ??????????????????????????!??????? Part3 ??(WMV)??(MP4)2011/4/26 ??????????????????????????!??????? Part4 ??(WMV)??(MP4)2011/5/26 ???????????Exadata???????????!Exadata???????????????????Tips??(WMV)??(MP4)2012/1/23 ?????????????????DB???????????!??TimesTen?????????? ??(WMV)??(MP4)2012/1/23 ???????????????????????????!GoldenGate?????????????????????(WMV)??(MP4)2012/1/23 ???????????EDA/CEP???????????!Oracle CEP?????????·?????????????(WMV)??(MP4)2012/1/23 ????????????????????????????????!???????????????????(WMV)??(MP4)2011/2/15 ???????????????????????????????RAC ????????????????(WMV)??(MP4)2012/1/23 ????????????????????????????????!Oracle Net ??????????????(WMV)??(MP4)2012/1/23 ?????????????????????????????:???????????????0??????(WMV)??(MP4)2010/5/19 ???????????????????????????!???????????????????????(WMV)??(MP4)2012/1/23 ?????????Oracle Real Application Clusters????????????!RAC????????????????????(WMV)??(MP4)2011/3/1 ???????Core Tech Oracle Database Core Tech SeminarOracle Data Guard,Oracle Recovery Manager(RMAN),Flashback??(WMV)??(MP4)2012/5/14 ???????Core Tech Oracle Database Core Tech SeminarOracle Real Application Clusters,Oracle Clusterware,Oracle Automatic Storage Management??(WMV)??(MP4)2012/5/14 ???????Big Data Appliance?????????????????????(WMV)??(MP4)2012/5/14 ???????Oracle Real Application ClustersRAC????10??!US Oracle??????????????Oracle Real Application Clusters????????????(WMV)??(MP4)2012/2/20 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ???????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ???????/?????????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12c Oracle Enterprise Manager 12c ???????/????????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ??????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ??????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ????????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ????????? ????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c Exadata?????(WMV)??(MP4)2012/1/23 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager 12c ???????????(WMV)??(MP4)2012/2/6 ???????Oracle Enterprise Manager 12cOracle Enterprise Manager???????????·?????????????(WMV)??(MP4)2012/5/14 ???????Database Appliance???????????1Box?????2???????? Oracle Database Appliance ??????(WMV)??(MP4)2011/12/19 ???????Database ApplianceOracle Database Appliance????????·????????(WMV)??(MP4)2012/5/14 ???????Oracle Data MiningOracle DB????!????????????(WMV)??(MP4)2010/9/14 ???????Oracle Data MiningOracleDB????????????(WMV)??(MP4)2011/6/29 OracleDirect ?????????????????!?????·???????ABC -Oracle Database???(WMV)??(MP4)2012/3/5 OracleDirect ???????????????????????-SE·EE??????-??(WMV)??(MP4)2010/5/19 OracleDirect ?????????????Oracle Database EE?SE???????????!???(WMV)??(MP4)2010/2/25 OracleDirect ????????????????98(????)???Oracle Database?????????! ~?????????????Oracle Database?????!~??(WMV)??(MP4)2009/12/2 OracleDirect ????????????!! Oracle Database????????(WMV)??(MP4)2010/10/13 OracleDirect ?????SQL?????????SQL?????????!SQL?????(WMV)??(MP4)2011/4/12 ???????????ACE????? ??Oracle Database???????(WMV)??(MP4)2012/5/14 ???????????????????????????????????????????? ??(WMV)??(MP4)2012/1/23 ????????????????!?????????????????·???????????? ????(WMV)??(MP4)2012/1/23 ????????????????!?????????????????·???????????? ????(WMV)??(MP4)2012/1/23 Java ???? ?? ????????? ??? ?? Java??Java EEJava EE 6 ??(132page)??(WMV)??(MP4)2011/04 Java?????!???????Java?????????(WMV)??(MP4)2011/06 Java??Java???????·???????????(WMV)??(MP4)2012/01 Java??Oracle ???? Java ??????? ??(WMV)??(MP4)2011/03 WebLogic Server/????????·???? ???? ?? ????????? ??? ?? WebLogic Server????Oracle????????WebLogic ????(WMV)??(MP4)2012/1/23 WebLogic Server????:????????? FastSwap??????·???????(??) ??(WMV)??(MP4)- WebLogic Server????:???????????????????(??)??(WMV)??(MP4)- WebLogic Server????:????????? ?????????????????????·??????????????????????(CAT)(??) ??(WMV)??(MP4)- WebLogic Server????:????????? ???????????????????????:????????????????????(??) ??(WMV)??(MP4)- WebLogic Server????:????????? JRockit Mission Control(??)??(WMV)??(MP4)- WebLogic Server????:????????? JRockit Flight Recorder????WebLogic????????????(??)??(WMV)??(MP4)- WebLogic Server????:????????? ?????????????? ???????????(??)??(WMV)??(MP4)- WebLogic Server????/???????????????????????????????????WebLogic????????(WMV)??(MP4)2011/3/24 WebLogic Server????WebLogic Server?JDBC??????????(WMV)??(MP4)2010/6/17 WebLogic Server????Oracle WebLogic Server???????Web??????? -???-??(WMV)??(MP4)2010/2/17 WebLogic Server????????????????? WebLogic Server ?????????????? ??(WMV)??(MP4)2012/1/23 WebLogic Server????????????????!WebLogic Scripting Tool?????WLS???·??????(WMV)??(MP4)2012/1/23 WebLogic Server????????????????????????~Oracle WebLogic Server 11g~??(WMV)??(MP4)2010/2/10 WebLogic Server????????????????!EM???WebLogic?????(WMV)??(MP4)2010/5/27 WebLogic Server ?????????????????WebLogic Server???????????????(WMV)??(MP4)2010/3/24 WebLogic Server????Oracle???????????????????????·????!??(WMV)??(MP4)2011/5/26 WebLogic Server??·????????OracleAS???????WebLogic Server??????????(WMV)??(MP4)2010/4/22 WebLogic ServerExalogicOracle Exalogic Elastic Cloud ?? ~ Exalogic ??? ~??(WMV)??(MP4)2012/1/23 JRockit??JVM JRockit?? ??Update??(WMV)??(MP4)2011/03 CoherenceOracle Coherence ?????·????????????????(WMV)??(MP4)2012/1/23 CoherenceOracle Coherence ????????????????(WMV)??(MP4)2012/1/23 Coherence???????????!???!Oracle Coherence?????????????????????????(WMV)??(MP4)2012/1/23 Coherence????????????Coherence??????(WMV)??(MP4)2011/04 SOA/BPM/????? ???? ?? ????????? ??? ?? BPM???????????BPM?????????????? ??(WMV)??(MP4)2011/04 BPMBPM Suite 11g??????????????????(WMV)??(MP4)2011/03 CEP??????????????????????????CEP????????(WMV)??(MP4)2011/04 ????????? ???? ?? ????????? ??? ?? ?????????????????????!???·????????????(WMV)??(MP4)2010/5/25 ???????Notes??????????????(WMV)??(MP4)2010/5/20 ???????Notes??13?????????????????????!??(WMV)??(MP4)2010/4/20 ??????????????????????Notes?????????????(WMV)??(MP4)2010/3/17 ???????Mashup Award5 ????????????????????????????????·?????????(WMV)??(MP4)2010/2/23 ID??/?????? ???? ?? ????????? ??? ?? ID????????????????!!~OracleDB?????????????????????????(WMV)??(MP4)2012/1/23 ID?????????????!????ID????????????(WMV)??(MP4)2010/6/15 ID???????????!????DB?OS?????/???????????(WMV)??(MP4)2010/1/27 ??????????/???????????????·???????????(WMV)??(MP4)2011/04 ?????????????~???????????????????(WMV)??(MP4)2011/4/5 ??????????!??ID·??????????????????(WMV)??(MP4)2010/12/7 ???????????????·???????????(WMV)??(MP4)2010/6/23 ?????EPM/BI EPM/BI ??????? ???? ?? ????????? ??? ?? ???BI????????????BI?????~5W1H1T?~??(WMV)??(MP4)2010/3/17 ???BI????????????BI?????~?????????~??(WMV)??(MP4)2010/2/24 ???????BI?????????? -Evidence-based Management- ??????????(WMV)??(MP4)2010/2/18 ???BI????????????BI?????~???KPI?~??(WMV)??(MP4)2010/1/28 EPM/BI ???? ???? ?? ????????? ??? ?? ??BIEE?????????????????(WMV)??(MP4)2010/3/10 OS/??? ???? ?? ????????? ??? ?? ???Solaris??????Oracle Solaris??????(WMV)??(MP4)2010/10/14 ???SolarisSolaris 10 ?? ~????Solaris???~??(WMV)??(MP4)2010/9/14 ???ZFSZFS ???! ZFS ???????(???)??(WMV)??(MP4)2011/11/21 ???ZFSZFS ???! ??????????????????(WMV)??(MP4)2010/9/28 ???LinuxOracle Linux?Unbreakable Enterprise Kernel?????(WMV)??(MP4)2011/11/21 ???LinuxOracle Linux Unbreakable Enterprise Kernel?????????(WMV)??(MP4)2012/5/14 ???Linux??????Oracle?????????Linux????(WMV)??(MP4)2010/5/25 ????????????????????????????????????(WMV)??(MP4)2012/1/6 ???????SolarisSolaris: ??????????????? ??(WMV)??(MP4)2011/1/27 ???????SolarisOracle Solaris 11????????????????? ??(WMV)??(MP4)2012/5/14 ???????SolarisSolaris ? DTrace ?????????????(WMV)??(MP4)2010/9/21 ???SolarisOracle Solaris 11 ??????????????-IPS ??????? ??(WMV)??(MP4)2012/5/14 ???SolarisSolaris ?????????????????????????????? ??(WMV)??(MP4)2012/5/14 ???ZFSZFS?Oracle UCM????????????? ??(WMV)??(MP4)2011/12/19 ???? ???? ?? ????????? ??? ?? ???SPARCSPARC ????? ~ OVM ???????!??(WMV)??(MP4)2011/12/5 ????? ???? ?? ????????? ??? ?? ???SAN????????????? Pillar Axiom 600 ???? ??(WMV)??(MP4)2012/4/23 ???ZFSOracleDB????SunStorage7000?????(WMV)??(MP4)2010/9/9 ????????!??????????????????????(WMV)??(MP4)2012/2/6 ???ZFS??S7000???:S7000????????????(WMV)??(MP4)2011/12/5 MySQL ???? ?? ????????? ??? ?? MySQL????MySQL????MySQL?????? ????????(WMV)??(MP4)2011/7/25 MySQL???MySQL??MySQL?? ?????(WMV)??(MP4)2012/1/23 MySQL???MySQL??MySQL?? ?????(WMV)??(MP4)2012/5/28 MySQL???MySQL??MySQL?? ???????(WMV)??(MP4)2012/6/25 MySQL???MySQL??MySQL???????(WMV)??(MP4)2011/7/25 MySQL????????????????MySQL ???????????????(WMV)??(MP4)2012/1/23 MySQL???MySQL Cluster MySQL Cluster ??????(WMV)??(MP4)2012/2/6 MySQL???MySQL Cluster MySQL Cluster 7.2 ??????(WMV)??(MP4)2012/3/19 MySQL??????? MySQL ????????(WMV)??(MP4)2012/2/6

  Read the article

• DTracing a PHPUnit Test: Looking at Functional Programming

  - by cj

  Here's a quick example of using DTrace Dynamic Tracing to work out what a PHP code base does. I was reading the article Functional Programming in PHP by Patkos Csaba and wondering how efficient this stype of programming is. I thought this would be a good time to fire up DTrace and see what is going on. Since DTrace is "always available" even in production machines (once PHP is compiled with --enable-dtrace), this was easy to do. I have Oracle Linux with the UEK3 kernel and PHP 5.5 with DTrace static probes enabled, as described in DTrace PHP Using Oracle Linux 'playground' Pre-Built Packages I installed the Functional Programming sample code and Sebastian Bergmann's PHPUnit. Although PHPUnit is included in the Functional Programming example, I found it easier to separately download and use its phar file: cd ~/Desktop wget -O master.zip https://github.com/tutsplus/functional-programming-in-php/archive/master.zip wget https://phar.phpunit.de/phpunit.phar unzip master.zip I created a DTrace D script functree.d: #pragma D option quiet self int indent; BEGIN { topfunc = $1; } php$target:::function-entry /copyinstr(arg0) == topfunc/ { self->follow = 1; } php$target:::function-entry /self->follow/ { self->indent += 2; printf("%*s %s%s%s\n", self->indent, "->", arg3?copyinstr(arg3):"", arg4?copyinstr(arg4):"", copyinstr(arg0)); } php$target:::function-return /self->follow/ { printf("%*s %s%s%s\n", self->indent, "<-", arg3?copyinstr(arg3):"", arg4?copyinstr(arg4):"", copyinstr(arg0)); self->indent -= 2; } php$target:::function-return /copyinstr(arg0) == topfunc/ { self->follow = 0; } This prints a PHP script function call tree starting from a given PHP function name. This name is passed as a parameter to DTrace, and assigned to the variable topfunc when the DTrace script starts. With this D script, choose a PHP function that isn't recursive, or modify the script to set self->follow = 0 only when all calls to that function have unwound. From looking at the sample FunSets.php code and its PHPUnit test driver FunSetsTest.php, I settled on one test function to trace: function testUnionContainsAllElements() { ... } I invoked DTrace to trace function calls invoked by this test with # dtrace -s ./functree.d -c 'php phpunit.phar \ /home/cjones/Desktop/functional-programming-in-php-master/FunSets/Tests/FunSetsTest.php' \ '"testUnionContainsAllElements"' The core of this command is a call to PHP to run PHPUnit on the FunSetsTest.php script. Outside that, DTrace is called and the PID of PHP is passed to the D script $target variable so the probes fire just for this invocation of PHP. Note the quoting around the PHP function name passed to DTrace. The parameter must have double quotes included so DTrace knows it is a string. The output is: PHPUnit 3.7.28 by Sebastian Bergmann. ......-> FunSetsTest::testUnionContainsAllElements -> FunSets::singletonSet <- FunSets::singletonSet -> FunSets::singletonSet <- FunSets::singletonSet -> FunSets::union <- FunSets::union -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertTrue -> PHPUnit_Framework_Assert::isTrue <- PHPUnit_Framework_Assert::isTrue -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertTrue -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertTrue -> PHPUnit_Framework_Assert::isTrue <- PHPUnit_Framework_Assert::isTrue -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertTrue -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertFalse -> PHPUnit_Framework_Assert::isFalse -> {closure} -> main <- main <- {closure} <- PHPUnit_Framework_Assert::isFalse -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsFalse::matches <- PHPUnit_Framework_Constraint_IsFalse::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertFalse <- FunSetsTest::testUnionContainsAllElements ... Time: 1.85 seconds, Memory: 3.75Mb OK (9 tests, 23 assertions) The periods correspond to the successful tests before and after (and from) the test I was tracing. You can see the function entry ("->") and return ("<-") points. Cross checking with the testUnionContainsAllElements() source code confirms the two singletonSet() calls, one union() call, two assertTrue() calls and finally an assertFalse() call. These assertions have a contains() call as a parameter, so contains() is called before the PHPUnit assertion functions are run. You can see contains() being called recursively, and how the closures are invoked. If you want to focus on the application logic and suppress the PHPUnit function trace, you could turn off tracing when assertions are being checked by adding D clauses checking the entry and exit of assertFalse() and assertTrue(). But if you want to see all of PHPUnit's code flow, you can modify the functree.d code that sets and unsets self-follow, and instead change it to toggle the variable in request-startup and request-shutdown probes: php$target:::request-startup { self->follow = 1 } php$target:::request-shutdown { self->follow = 0 } Be prepared for a large amount of output!

  Read the article

• A New Threat To Web Applications: Connection String Parameter Pollution (CSPP)

  - by eric.maurice

  Hi, this is Shaomin Wang. I am a security analyst in Oracle's Security Alerts Group. My primary responsibility is to evaluate the security vulnerabilities reported externally by security researchers on Oracle Fusion Middleware and to ensure timely resolution through the Critical Patch Update. Today, I am going to talk about a serious type of attack: Connection String Parameter Pollution (CSPP). Earlier this year, at the Black Hat DC 2010 Conference, two Spanish security researchers, Jose Palazon and Chema Alonso, unveiled a new class of security vulnerabilities, which target insecure dynamic connections between web applications and databases. The attack called Connection String Parameter Pollution (CSPP) exploits specifically the semicolon delimited database connection strings that are constructed dynamically based on the user inputs from web applications. CSPP, if carried out successfully, can be used to steal user identities and hijack web credentials. CSPP is a high risk attack because of the relative ease with which it can be carried out (low access complexity) and the potential results it can have (high impact). In today's blog, we are going to first look at what connection strings are and then review the different ways connection string injections can be leveraged by malicious hackers. We will then discuss how CSPP differs from traditional connection string injection, and the measures organizations can take to prevent this kind of attacks. In web applications, a connection string is a set of values that specifies information to connect to backend data repositories, in most cases, databases. The connection string is passed to a provider or driver to initiate a connection. Vendors or manufacturers write their own providers for different databases. Since there are many different providers and each provider has multiple ways to make a connection, there are many different ways to write a connection string. Here are some examples of connection strings from Oracle Data Provider for .Net/ODP.Net: Oracle Data Provider for .Net / ODP.Net; Manufacturer: Oracle; Type: .NET Framework Class Library: - Using TNS Data Source = orcl; User ID = myUsername; Password = myPassword; - Using integrated security Data Source = orcl; Integrated Security = SSPI; - Using the Easy Connect Naming Method Data Source = username/password@//myserver:1521/my.server.com - Specifying Pooling parameters Data Source=myOracleDB; User Id=myUsername; Password=myPassword; Min Pool Size=10; Connection Lifetime=120; Connection Timeout=60; Incr Pool Size=5; Decr Pool Size=2; There are many variations of the connection strings, but the majority of connection strings are key value pairs delimited by semicolons. Attacks on connection strings are not new (see for example, this SANS White Paper on Securing SQL Connection String). Connection strings are vulnerable to injection attacks when dynamic string concatenation is used to build connection strings based on user input. When the user input is not validated or filtered, and malicious text or characters are not properly escaped, an attacker can potentially access sensitive data or resources. For a number of years now, vendors, including Oracle, have created connection string builder class tools to help developers generate valid connection strings and potentially prevent this kind of vulnerability. Unfortunately, not all application developers use these utilities because they are not aware of the danger posed by this kind of attacks. So how are Connection String parameter Pollution (CSPP) attacks different from traditional Connection String Injection attacks? First, let's look at what parameter pollution attacks are. Parameter pollution is a technique, which typically involves appending repeating parameters to the request strings to attack the receiving end. Much of the public attention around parameter pollution was initiated as a result of a presentation on HTTP Parameter Pollution attacks by Stefano Di Paola and Luca Carettoni delivered at the 2009 Appsec OWASP Conference in Poland. In HTTP Parameter Pollution attacks, an attacker submits additional parameters in HTTP GET/POST to a web application, and if these parameters have the same name as an existing parameter, the web application may react in different ways depends on how the web application and web server deal with multiple parameters with the same name. When applied to connections strings, the rule for the majority of database providers is the "last one wins" algorithm. If a KEYWORD=VALUE pair occurs more than once in the connection string, the value associated with the LAST occurrence is used. This opens the door to some serious attacks. By way of example, in a web application, a user enters username and password; a subsequent connection string is generated to connect to the back end database. Data Source = myDataSource; Initial Catalog = db; Integrated Security = no; User ID = myUsername; Password = XXX; In the password field, if the attacker enters "xxx; Integrated Security = true", the connection string becomes, Data Source = myDataSource; Initial Catalog = db; Integrated Security = no; User ID = myUsername; Password = XXX; Intergrated Security = true; Under the "last one wins" principle, the web application will then try to connect to the database using the operating system account under which the application is running to bypass normal authentication. CSPP poses serious risks for unprepared organizations. It can be particularly dangerous if an Enterprise Systems Management web front-end is compromised, because attackers can then gain access to control panels to configure databases, systems accounts, etc. Fortunately, organizations can take steps to prevent this kind of attacks. CSPP falls into the Injection category of attacks like Cross Site Scripting or SQL Injection, which are made possible when inputs from users are not properly escaped or sanitized. Escaping is a technique used to ensure that characters (mostly from user inputs) are treated as data, not as characters, that is relevant to the interpreter's parser. Software developers need to become aware of the danger of these attacks and learn about the defenses mechanism they need to introduce in their code. As well, software vendors need to provide templates or classes to facilitate coding and eliminate developers' guesswork for protecting against such vulnerabilities. Oracle has introduced the OracleConnectionStringBuilder class in Oracle Data Provider for .NET. Using this class, developers can employ a configuration file to provide the connection string and/or dynamically set the values through key/value pairs. It makes creating connection strings less error-prone and easier to manager, and ultimately using the OracleConnectionStringBuilder class provides better security against injection into connection strings. For More Information: - The OracleConnectionStringBuilder is located at http://download.oracle.com/docs/cd/B28359_01/win.111/b28375/OracleConnectionStringBuilderClass.htm - Oracle has developed a publicly available course on preventing SQL Injections. The Server Technologies Curriculum course "Defending Against SQL Injection Attacks!" is located at http://st-curriculum.oracle.com/tutorial/SQLInjection/index.htm - The OWASP web site also provides a number of useful resources. It is located at http://www.owasp.org/index.php/Main_Page

  Read the article

• Running Solaris 11 as a control domain on a T2000

  - by jsavit

  There is increased adoption of Oracle Solaris 11, and many customers are deploying it on systems that previously ran Solaris 10. That includes older T1-processor based systems like T1000 and T2000. Even though they are old (from 2005) and don't have the performance of current SPARC servers, they are still functional, stable servers that customers continue to operate. One reason to install Solaris 11 on them is that older machines are attractive for testing OS upgrades before updating current, production systems. Normally this does not present a challenge, because Solaris 11 runs on any T-series or M-series SPARC server. One scenario adds a complication: running Solaris 11 in a control domain on a T1000 or T2000 hosting logical domains. Solaris 11 pre-installed Oracle VM Server for SPARC incompatible with T1 Unlike Solaris 10, Solaris 11 comes with Oracle VM Server for SPARC preinstalled. The ldomsmanager package contains the logical domains manager for Oracle VM Server for SPARC 2.2, which requires a SPARC T2, T2+, T3, or T4 server. It does not work with T1-processor systems, which are only supported by LDoms Manager 1.2 and earlier. The following screenshot shows what happens (bold font) if you try to use Oracle VM Server for SPARC 2.x commands in a Solaris 11 control domain. The commands were issued in a control domain on a T2000 that previously ran Solaris 10. We also display the version of the logical domains manager installed in Solaris 11: root@t2000 psrinfo -vp The physical processor has 4 virtual processors (0-3) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep T SUNW,Sun-Fire-T200 # ldm -V Failed to connect to logical domain manager: Connection refused # pkg info ldomsmanager Name: system/ldoms/ldomsmanager Summary: Logical Domains Manager Description: LDoms Manager - Virtualization for SPARC T-Series Category: System/Virtualization State: Installed Publisher: solaris Version: 2.2.0.0 Build Release: 5.11 Branch: 0.175.0.8.0.3.0 Packaging Date: May 25, 2012 10:20:48 PM Size: 2.86 MB FMRI: pkg://solaris/system/ldoms/[email protected],5.11-0.175.0.8.0.3.0:20120525T222048Z The 2.2 version of the logical domains manager will have to be removed, and 1.2 installed, in order to use this as a control domain. Preparing to change - create a new boot environment Before doing anything else, lets create a new boot environment: # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris NR / 2.14G static 2012-09-25 10:32 # beadm create solaris-1 # beadm activate solaris-1 # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris N / 4.82M static 2012-09-25 10:32 solaris-1 R - 2.14G static 2012-09-29 11:40 # init 0 Normally an init 6 to reboot would have been sufficient, but in the next step I reset the system anyway in order to put the system in factory default mode for a "clean" domain configuration. Preparing to change - reset to factory default There was a leftover domain configuration on the T2000, so I reset it to the factory install state. Since the ldm command is't working yet, it can't be done from the control domain, so I did it by logging onto to the service processor: $ ssh -X admin@t2000-sc Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved. Oracle Advanced Lights Out Manager CMT v1.7.9 Please login: admin Please Enter password: ******** sc> showhost Sun-Fire-T2000 System Firmware 6.7.10 2010/07/14 16:35 Host flash versions: OBP 4.30.4.b 2010/07/09 13:48 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 sc> bootmode config="factory-default" sc> poweroff Are you sure you want to power off the system [y/n]? y SC Alert: SC Request to Power Off Host. SC Alert: Host system has shut down. sc> poweron SC Alert: Host System has Reset At this point I rebooted into the new Solaris 11 boot environment, and Solaris commands showed it was running on the factory default configuration of a single domain owning all 32 CPUs and 32GB of RAM (that's what it looked like in 2005.) # psrinfo -vp The physical processor has 8 cores and 32 virtual processors (0-31) The core has 4 virtual processors (0-3) The core has 4 virtual processors (4-7) The core has 4 virtual processors (8-11) The core has 4 virtual processors (12-15) The core has 4 virtual processors (16-19) The core has 4 virtual processors (20-23) The core has 4 virtual processors (24-27) The core has 4 virtual processors (28-31) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep Mem Memory size: 32640 Megabytes Note that the older processor has 4 virtual CPUs per core, while current processors have 8 per core. Remove ldomsmanager 2.2 and install the 1.2 version The Solaris 11 pkg command is now used to remove the 2.2 version that shipped with Solaris 11: # pkg uninstall ldomsmanager Packages to remove: 1 Create boot environment: No Create backup boot environment: No Services to change: 2 PHASE ACTIONS Removal Phase 130/130 PHASE ITEMS Package State Update Phase 1/1 Package Cache Update Phase 1/1 Image State Update Phase 2/2 Finally, LDoms 1.2 installed via its install script, the same way it was done years ago: # unzip LDoms-1_2-Integration-10.zip # cd LDoms-1_2-Integration-10/Install/ # ./install-ldm Welcome to the LDoms installer. You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. ... ... normal install messages omitted ... The Solaris Security Toolkit applies to Solaris 10, and cannot be used in Solaris 11 (in which several things hardened by the Toolkit are already hardened by default), so answer b in the choice below: You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. Select a security profile from this list: a) Hardened Solaris configuration for LDoms (recommended) b) Standard Solaris configuration c) Your custom-defined Solaris security configuration profile Enter a, b, or c [a]: b ... other install messages omitted for brevity... After install I ensure that the necessary services are enabled, and verify the version of the installed LDoms Manager: # svcs ldmd STATE STIME FMRI online 22:00:36 svc:/ldoms/ldmd:default # svcs vntsd STATE STIME FMRI disabled Aug_19 svc:/ldoms/vntsd:default # ldm -V Logical Domain Manager (v 1.2-debug) Hypervisor control protocol v 1.3 Using Hypervisor MD v 1.1 System PROM: Hypervisor v. 1.7.3. @(#)Hypervisor 1.7.3.c 2010/07/09 15:14\015 OpenBoot v. 4.30.4. @(#)OBP 4.30.4.b 2010/07/09 13:48 Set up control domain and domain services At this point we have a functioning LDoms 1.2 environment that can be configured in the usual fashion. One difference is that LDoms 1.2 behavior had 'delayed configuration mode (as expected) during initial configuration before rebooting the control domain. Another minor difference with a Solaris 11 control domain is that you define virtual switches using the 'vanity name' of the network interface, rather than the hardware driver name as in Solaris 10. # ldm list ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Configuration and resource information is displayed for the configuration under construction; not the current active configuration. The configuration being constructed will only take effect after it is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-c-- SP 32 32640M 3.2% 4d 2h 50m # ldm add-vdiskserver primary-vds0 primary # ldm add-vconscon port-range=5000-5100 primary-vcc0 primary # ldm add-vswitch net-dev=net0 primary-vsw0 primary # ldm set-mau 2 primary # ldm set-vcpu 8 primary # ldm set-memory 4g primary # ldm add-config initial # ldm list-spconfig factory-default initial [current] That's it, really. After reboot, we are ready to install guest domains. Summary - new wine in old bottles This example shows that (new) Solaris 11 can be installed on (old) T2000 servers and used as a control domain. The main activity is to remove the preinstalled Oracle VM Server for 2.2 and install Logical Domains 1.2 - the last version of LDoms to support T1-processor systems. I tested Solaris 10 and Solaris 11 guest domains running on this server and they worked without any surprises. This is a viable way to get further into Solaris 11 adoption, even on older T-series equipment.

  Read the article

• Oracle Tutor: Top 10 to Implement Sustainable Policies and Procedures

  - by emily.chorba(at)oracle.com

  Overview Your organization (executives, managers, and employees) understands the value of having written business process documents (process maps, procedures, instructions, reference documents, and form abstracts). Policies and procedures should be documented because they help to reduce the range of individual decisions and encourage management by exception: the manager only needs to give special attention to unusual problems, not covered by a specific policy or procedure. As more and more procedures are written to cover recurring situations, managers will begin to make decisions which will be consistent from one functional area to the next.Companies should take a project management approach when implementing an environment for a sustainable documentation program and do the following:1. Identify an Executive Champion2. Put together a winning team3. Assign ownership4. Centralize publishing5. Establish the Document Maintenance Process Up Front6. Document critical activities only7. Document actual practice8. Minimize documentation9. Support continuous improvement10. Keep it simple 1. Identify an Executive ChampionAppoint a top down driver. Select one key individual to be a mentor for the procedure planning team. The individual should be a senior manager, such as your company president, CIO, CFO, the vice-president of quality, manufacturing, or engineering. Written policies and procedures can be important supportive aids when known to express the thinking for the chief executive officer and / or the president and to have his or her full support. 2. Put Together a Winning TeamChoose a strong Project Management Leader and staff the procedure planning team with management members from cross functional groups. Make sure team members have the responsibility - and the authority - to make things happen.The winning team should consist of the Documentation Project Manager, Document Owners (one for each functional area), a Document Controller, and Document Specialists (as needed). The Tutor Implementation Guide has complete job descriptions for these roles. 3. Assign Ownership It is virtually impossible to keep process documentation simple and meaningful if employees who are far removed from the activity itself create it. It is impossible to keep documentation up-to-date when responsibility for the document is not clearly understood.Key to the Tutor methodology, therefore, is the concept of ownership. Each document has a single owner, who is responsible for ensuring that the document is necessary and that it reflects actual practice. The owner must be a person who is knowledgeable about the activity and who has the authority to build consensus among the persons who participate in the activity as well as the authority to define or change the way an activity is performed. The owner must be an advocate of the performers and negotiate, not dictate practices.In the Tutor environment, a document's owner is the only person with the authority to approve an update to that document. 4. Centralize Publishing Although it is tempting (especially in a networked environment and with document management software solutions) to decentralize the control of all documents -- with each owner updating and distributing his own -- Tutor promotes centralized publishing by assigning the Document Administrator (gate keeper) to manage the updates and distribution of the procedures library. 5. Establish a Document Maintenance Process Up Front (and stick to it) Everyone in your organization should know they are invited to suggest changes to procedures and should understand exactly what steps to take to do so. Tutor provides a set of procedures to help your company set up a healthy document control system. There are many document management products available to automate some of the document change and maintenance steps. Depending on the size of your organization, a simple document management system can reduce the effort it takes to track and distribute document changes and updates. Whether your company decides to store the written policies and procedures on a file server or in a database, the essential tasks for maintaining documents are the same, though some tasks are automated. 6. Document Critical Activities Only The best way to keep your documentation simple is to reduce the number of process documents to a bare minimum and to include in those documents only as much detail as is absolutely necessary. The first step to reducing process documentation is to document only those activities that are deemed critical. Not all activities require documentation. In fact, some critical activities cannot and should not be standardized. Others may be sufficiently documented with an instruction or a checklist and may not require a procedure. A document should only be created when it enhances the performance of the employee performing the activity. If it does not help the employee, then there is no reason to maintain the document. Activities that represent little risk (such as project status), activities that cannot be defined in terms of specific tasks (such as product research), and activities that can be performed in a variety of ways (such as advertising) often do not require documentation. Sometimes, an activity will evolve to the point where documentation is necessary. For example, an activity performed by single employee may be straightforward and uncomplicated -- that is, until the activity is performed by multiple employees. Sometimes, it is the interaction between co-workers that necessitates documentation; sometimes, it is the complexity or the diversity of the activity.7. Document Actual Practices The only reason to maintain process documentation is to enhance the performance of the employee performing the activity. And documentation can only enhance performance if it reflects reality -- that is, current best practice. Documentation that reflects an unattainable ideal or outdated practices will end up on the shelf, unused and forgotten.Documenting actual practice means (1) auditing the activity to understand how the work is really performed, (2) identifying best practices with employees who are involved in the activity, (3) building consensus so that everyone agrees on a common method, and (4) recording that consensus.8. Minimize Documentation One way to keep it simple is to document at the highest level possible. That is, include in your documents only as much detail as is absolutely necessary.When writing a document, you should ask yourself, What is the purpose of this document? That is, what problem will it solve?By focusing on this question, you can target the critical information.• What questions are the end users likely to have?• What level of detail is required?• Is any of this information extraneous to the document's purpose? Short, concise documents are user friendly and they are easier to keep up to date. 9. Support Continuous Improvement Employees who perform an activity are often in the best position to identify improvements to the process. In other words, continuous improvement is a natural byproduct of the work itself -- but only if the improvements are communicated to all employees who are involved in the process, and only if there is consensus among those employees.Traditionally, process documentation has been used to dictate performance, to limit employees' actions. In the Tutor environment, process documents are used to communicate improvements identified by employees. How does this work? The Tutor methodology requires a process document to reflect actual practice, so the owner of a document must routinely audit its content -- does the document match what the employees are doing? If it doesn't, the owner has the responsibility to evaluate the process, to build consensus among the employees, to identify "best practices," and to communicate these improvements via a document update. Continuous improvement can also be an outgrowth of corrective action -- but only if the solutions to problems are communicated effectively. The goal should be to solve a problem once and only once, which means not only identifying the solution, but ensuring that the solution becomes part of the process. The Tutor system provides the method through which improvements and solutions are documented and communicated to all affected employees in a cost-effective, timely manner; it ensures that improvements are not lost or confined to a single employee. 10. Keep it Simple Process documents don't have to be complex and unfriendly. In fact, the simpler the format and organization, the more likely the documents will be used. And the simpler the method of maintenance, the more likely the documents will be kept up-to-date. Keep it simply by:• Minimizing skills and training required• Following the established Tutor document format and layout• Avoiding technology just for technology's sake No other rule has as major an impact on the success of your internal documentation as -- keep it simple. Learn More For more information about Tutor, visit Oracle.Com or the Tutor Blog. Post your questions at the Tutor Forum.   Emily Chorba Principle Product Manager Oracle Tutor & BPM 

  Read the article

• How to Tell a Hardware Problem From a Software Problem

  - by Chris Hoffman

  Your computer seems to be malfunctioning — it’s slow, programs are crashing or Windows may be blue-screening. Is your computer’s hardware failing, or does it have a software problem that you can fix on your own? This can actually be a bit tricky to figure out. Hardware problems and software problems can lead to the same symptoms — for example, frequent blue screens of death may be caused by either software or hardware problems. Computer is Slow We’ve all heard the stories — someone’s computer slows down over time because they install too much software that runs at startup or it becomes infected with malware. The person concludes that their computer is slowing down because it’s old, so they replace it. But they’re wrong. If a computer is slowing down, it has a software problem that can be fixed. Hardware problems shouldn’t cause your computer to slow down. There are some rare exceptions to this — perhaps your CPU is overheating and it’s downclocking itself, running slower to stay cooler — but most slowness is caused by software issues. Blue Screens Modern versions of Windows are much more stable than older versions of Windows. When used with reliable hardware with well-programmed drivers, a typical Windows computer shouldn’t blue-screen at all. If you are encountering frequent blue screens of death, there’s a good chance your computer’s hardware is failing. Blue screens could also be caused by badly programmed hardware drivers, however. If you just installed or upgraded hardware drivers and blue screens start, try uninstalling the drivers or using system restore — there may be something wrong with the drivers. If you haven’t done anything with your drivers recently and blue screens start, there’s a very good chance you have a hardware problem. Computer Won’t Boot If your computer won’t boot, you could have either a software problem or a hardware problem. Is Windows attempting to boot and failing part-way through the boot process, or does the computer no longer recognize its hard drive or not power on at all? Consult our guide to troubleshooting boot problems for more information. When Hardware Starts to Fail… Here are some common components that can fail and the problems their failures may cause: Hard Drive: If your hard drive starts failing, files on your hard drive may become corrupted. You may see long delays when you attempt to access files or save to the hard drive. Windows may stop booting entirely. CPU: A failing CPU may result in your computer not booting at all. If the CPU is overheating, your computer may blue-screen when it’s under load — for example, when you’re playing a demanding game or encoding video. RAM: Applications write data to your RAM and use it for short-term storage. If your RAM starts failing, an application may write data to part of the RAM, then later read it back and get an incorrect value. This can result in application crashes, blue screens, and file corruption. Graphics Card: Graphics card problems may result in graphical errors while rendering 3D content or even just while displaying your desktop. If the graphics card is overheating, it may crash your graphics driver or cause your computer to freeze while under load — for example, when playing demanding 3D games. Fans: If any of the fans fail in your computer, components may overheat and you may see the above CPU or graphics card problems. Your computer may also shut itself down abruptly so it doesn’t overheat any further and damage itself. Motherboard: Motherboard problems can be extremely tough to diagnose. You may see occasional blue screens or similar problems. Power Supply: A malfunctioning power supply is also tough to diagnose — it may deliver too much power to a component, damaging it and causing it to malfunction. If the power supply dies completely, your computer won’t power on and nothing will happen when you press the power button. Other common problems — for example, a computer slowing down — are likely to be software problems. It’s also possible that software problems can cause many of the above symptoms — malware that hooks deep into the Windows kernel can cause your computer to blue-screen, for example. The Only Way to Know For Sure We’ve tried to give you some idea of the difference between common software problems and hardware problems with the above examples. But it’s often tough to know for sure, and troubleshooting is usually a trial-and-error process. This is especially true if you have an intermittent problem, such as your computer blue-screening a few times a week. You can try scanning your computer for malware and running System Restore to restore your computer’s system software back to its previous working state, but these aren’t  guaranteed ways to fix software problems. The best way to determine whether the problem you have is a software or hardware one is to bite the bullet and restore your computer’s software back to its default state. That means reinstalling Windows or using the Refresh or reset feature on Windows 8. See whether the problem still persists after you restore its operating system to its default state. If you still see the same problem – for example, if your computer is blue-screening and continues to blue-screen after reinstalling Windows — you know you have a hardware problem and need to have your computer fixed or replaced. If the computer crashes or freezes while reinstalling Windows, you definitely have a hardware problem. Even this isn’t a completely perfect method — for example, you may reinstall Windows and install the same hardware drivers afterwards. If the hardware drivers are badly programmed, the blue-screens may continue. Blue screens of death aren’t as common on Windows these days — if you’re encountering them frequently, you likely have a hardware problem. Most blue screens you encounter will likely be caused by hardware issues. On the other hand, other common complaints like “my computer has slowed down” are easily fixable software problems. When in doubt, back up your files and reinstall Windows. Image Credit: Anders Sandberg on Flickr, comedy_nose on Flickr     

  Read the article

• The Great Divorce

  - by BlackRabbitCoder

  I have a confession to make: I've been in an abusive relationship for more than 17 years now.  Yes, I am not ashamed to admit it, but I'm finally doing something about it. I met her in college, she was new and sexy and amazingly fast -- and I'd never met anything like her before.  Her style and her power captivated me and I couldn't wait to learn more about her.  I took a chance on her, and though I learned a lot from her -- and will always be grateful for my time with her -- I think it's time to move on. Her name was C++, and she so outshone my previous love, C, that any thoughts of going back evaporated in the heat of this new romance.  She promised me she'd be gentle and not hurt me the way C did.  She promised me she'd clean-up after herself better than C did.  She promised me she'd be less enigmatic and easier to keep happy than C was.  But I was deceived.  Oh sure, as far as truth goes, it wasn't a complete lie.  To some extent she was more fun, more powerful, safer, and easier to maintain.  But it just wasn't good enough -- or at least it's not good enough now. I loved C++, some part of me still does, it's my first-love of programming languages and I recognize its raw power, its blazing speed, and its improvements over its predecessor.  But with today's hardware, at speeds we could only dream to conceive of twenty years ago, that need for speed -- at the cost of all else -- has died, and that has left my feelings for C++ moribund. If I ever need to write an operating system or a device driver, then I might need that speed.  But 99% of the time I don't.  I'm a business-type programmer and chances are 90% of you are too, and even the ones who need speed at all costs may be surprised by how much you sacrifice for that.   That's not to say that I don't want my software to perform, and it's not to say that in the business world we don't care about speed or that our job is somehow less difficult or technical.  There's many times we write programs to handle millions of real-time updates or handle thousands of financial transactions or tracking trading algorithms where every second counts.  But if I choose to write my code in C++ purely for speed chances are I'll never notice the speed increase -- and equally true chances are it will be far more prone to crash and far less easy to maintain.  Nearly without fail, it's the macro-optimizations you need, not the micro-optimizations.  If I choose to write a O(n2) algorithm when I could have used a O(n) algorithm -- that can kill me.  If I choose to go to the database to load a piece of unchanging data every time instead of caching it on first load -- that too can kill me.  And if I cross the network multiple times for pieces of data instead of getting it all at once -- yes that can also kill me.  But choosing an overly powerful and dangerous mid-level language to squeeze out every last drop of performance will realistically not make stock orders process any faster, and more likely than not open up the system to more risk of crashes and resource leaks. And that's when my love for C++ began to die.  When I noticed that I didn't need that speed anymore.  That that speed was really kind of a lie.  Sure, I can be super efficient and pack bits in a byte instead of using separate boolean values.  Sure, I can use an unsigned char instead of an int.  But in the grand scheme of things it doesn't matter as much as you think it does.  The key is maintainability, and that's where C++ failed me.  I like to tell the other developers I work with that there's two levels of correctness in coding: Is it immediately correct? Will it stay correct? That is, you can hack together any piece of code and make it correct to satisfy a task at hand, but if a new developer can't come in tomorrow and make a fairly significant change to it without jeopardizing that correctness, it won't stay correct. Some people laugh at me when I say I now prefer maintainability over speed.  But that is exactly the point.  If you focus solely on speed you tend to produce code that is much harder to maintain over the long hall, and that's a load of technical debt most shops can't afford to carry and end up completely scrapping code before it's time.  When good code is written well for maintainability, though, it can be correct both now and in the future. And you know the best part is?  My new love is nearly as fast as C++, and in some cases even faster -- and better than that, I know C# will treat me right.  Her creators have poured hundreds of thousands of hours of time into making her the sexy beast she is today.  They made her easy to understand and not an enigmatic mess.  They made her consistent and not moody and amorphous.  And they made her perform as fast as I care to go by optimizing her both at compile time and a run-time. Her code is so elegant and easy on the eyes that I'm not worried where she will run to or what she'll pull behind my back.  She is powerful enough to handle all my tasks, fast enough to execute them with blazing speed, maintainable enough so that I can rely on even fairly new peers to modify my work, and rich enough to allow me to satisfy any need.  C# doesn't ask me to clean up her messes!  She cleans up after herself and she tries to make my life easier for me by taking on most of those optimization tasks C++ asked me to take upon myself.  Now, there are many of you who would say that I am the cause of my own grief, that it was my fault C++ didn't behave because I didn't pay enough attention to her.  That I alone caused the pain she inflicted on me.  And to some extent, you have a point.  But she was so high maintenance, requiring me to know every twist and turn of her vast and unrestrained power that any wrong term or bout of forgetfulness was met with painful reminders that she wasn't going to watch my back when I made a mistake.  But C#, she loves me when I'm good, and she loves me when I'm bad, and together we make beautiful code that is both fast and safe. So that's why I'm leaving C++ behind.  She says she's changing for me, but I have no interest in what C++0x may bring.  Oh, I'll still keep in touch, and maybe I'll see her now and again when she brings her problems to my door and asks for some attention -- for I always have a soft spot for her, you see.  But she's out of my house now.  I have three kids and a dog and a cat, and all require me to clean up after them, why should I have to clean up after my programming language as well?

  Read the article

• H1 Visa interview tips–What you must know before attending the interview?

  - by Gopinath

  USA’s H1 visa allows highly qualified professionals from other countries to work in America. Many IT professionals in India aspire to go to USA on H1 and work for their clients. Recently I had a chance to study H1 visa process to help one of my friends and I would like to share what I learned. With the assumption that your H1 petition is approved and you got an interview scheduled at US Embassy for your visa stamping, here are tips you must know before attending the interview Dress Code – Formals Say no to casuals or any fancy dress when you attend the interview. It’s not a party or friends home you are visiting. Consider H1 Visa interview as your job interview and dress up in formals. There is no option B for your, you must be in formals. A plain formal shirt with a matching pant is suggested for men. Tie and Suit would not be required, but if you are a professional at management level you can consider wearing suit. Women can wear either formal Salwar or formal pant-shirt. Avoid heavy jewellery, wear what is must as per your tradition or culture. Body Language -  Smile on your face Your body language reflects what you are and what’s going on in your mind. Don’t be nervous or restless, be relaxed and wear a beautiful smile on your face. A smile is a curve that sets everything straight. When you are called for the interview, greet the interviewer with a beautiful smile. Say Good Morning/Afternoon/Evening depending on time you are visiting them. Whenever appropriate say Thank You. Generally American professionals are very friendly people and they reciprocate for your greetings. Make sure that you make them comfortable to start the interview. Carry original documents in a separate folder I don’t want to talk much about the documents that are required for your H1B interview as it’s big subject on it’s own and it requires a separate post. I assume that your consultant or employer helped you in gathering all the required documents like – petition, DS 160 forms, education & job related documents, resume, interview call letters, client letters, etc. For all the documents you are going to submit at the interview make sure that you have originals in a separate folder.  If required interviewer may ask you show the originals of any of the document you submitted for visa processing. Don’t mix the original documents with the documents you need to submit for interview. Have a separate folder for them. For those who are going to stamping along with their spouse and children, they need to carry few extra original documents like – marriage certificate, marriage photos(30 numbers)/album, birth certificates, passports, education and profession related certificates of the spouse and children. Know your role & responsibilities The interviewer will ask you questions on your roles and responsibilities at client location. Be clear what is your day to day tasks at client place and prepared to face detailed questions on the same. When asked explain clearly and also make sure what you say is inline with what is mentioned in your petition and client invitation letter. At times they may ask you questions specific to the project/technology you are going to work. So doing some homework in this area will help you easily answer the questions. Failing to answer basic questions on your role & responsibilities may result in rejection. You work for your Employer at Client location but NOT FOR CLIENT One of the important things to keep in mind that you work for your employer and you are being deputed to client location on a work visa.  Your employer is going to be solely responsible for your salary, work, promotion, pay hikes or what so ever during your stay at USA. Your client will not be responsible for anything. Lets say you are employed with Company X in India and they are applying for H1B to work at your client(ex: Microsoft) in USA, you must keep in my mind that Microsoft is not your employer. Microsoft will not pay your salaries or responsible for any employment related activities. Company X will be solely responsible for all your employer related activities. If you don’t get this correctly and say to Visa interviewer that your client is responsible, then you may get into troubles. Know your client It’s always good to know the clients with whom you are going to work in USA and their business. If your client is a well know organisation then you may not get many questions from interviewer else you need to be well prepared to provide details like – nature of business, location, size of the organisation, etc.  Get to know the basic details about your client and be confident while providing those details to the interviewer. Also make sure that you never talk about any confidential details of your client projects and business. Revealing confidential details of your client may land your job itself in soup. Make sure that your spouse is also in sync with you If you’ve applied a H4 visa for your spouse along with your H1, make sure that spouse is in sync with you. Your spouse also should know the basic details of your job, your employer, client and location where you will be travelling. Your spouse should also be prepared to answers questions related to marriage, their profession(if working), kids, education, etc. Interviewers will try to asses your spouse communication skills, whereabouts while staying in USA and would they prefer to work USA or not. On H4, which is a dependent visa, your spouse is not allowed to work in USA and at any point your spouse should not show the intentions to search for work in USA. Less luggage more comfort You would have definitely heard that there are lot of restrictions on what you can carry along with you to an US Embassy while attending the interview. To be frank it’s not good to say there are many restrictions, but there are a hell a lot of restrictions. There are unbelievable restrictions and it’s for the safety of everyone. You are not allowed to carry mobile phones, CD/DVDs, USBs, bank cards, cameras, cosmetics, food(except baby food), water, wallets, backpacks, sealed covers, etc. Trust me most of the things we carry with us regularly every day are not allowed inside. As there are 100s of restrictions, it would be easier if you understand what you can carry along with you and just carry them alone. Ask your employer/consultant to provide you a checklist of items that you can carry. Most what you would require are H1B related documents provided by the employer/consultant Photographs All original documents supporting your H1B Passports Some cash for your travel expenses (avoid coins) Any important phone number / details written in a paper(like your cab driver number, etc.) If you carry restricted stuff then you will be stopped at security checks, you have to find people who can safely keep all the restricted items. Due to heavy restrictions in and around the US Embassy you will not find any  place to keep your luggage. So just carry the bare minimum things required so that you feel more comfortable. Useful Links THE U.S. NON IMMIGRANT VISA APPLICATION PROCESS U.S VISA SECURITY REGULATIONS GENERAL FAQS Hope this information is helpful to you and best of luck for your interview. Creative commons Image credit: Flickr/ alexfrance, vinothchandar. hughelectronic, architratan, striatic

  Read the article

• Orchestrating the Virtual Enterprise

  - by John Murphy

  During the American Industrial Revolution, the Ford Motor Company did it all. It turned raw materials into a showroom full of Model Ts. It owned a steel mill, a glass factory, and an automobile assembly line. The company was both self-sufficient and innovative and went on to become one of the largest and most profitable companies in the world. Nowadays, it's unusual for any business to follow this vertical integration model because its much harder to be best in class across such a wide a range of capabilities and services. Instead, businesses focus on their core competencies and outsource other business functions to specialized suppliers. They exchange vertical integration for collaboration. When done well, all parties benefit from this arrangement and the collaboration leads to the creation of an agile, lean and successful "virtual enterprise." Case in point: For Sun hardware, Oracle outsources most of its manufacturing and all of its logistics to third parties. These are vital activities, but ones where Oracle doesn't have a core competency, so we shift them to business partners who do. Within our enterprise, we always retain the core functions of product development, support, and most of the sales function, because that's what constitutes our core value to our customers. This is a perfect example of a virtual enterprise.  What are the implications of this? It means that we must exchange direct internal control for indirect external collaboration. This fundamentally changes the relative importance of different business processes, the boundaries of security and information sharing, and the relationship of the supply chain systems to the ERP. The challenge is that the systems required to support this virtual paradigm are still mired in "island enterprise" thinking. But help is at hand. Developments such as the Web, social networks, collaboration, and rules-based orchestration offer great potential to fundamentally re-architect supply chain systems to better support the virtual enterprise.  Supply Chain Management Systems in a Virtual Enterprise Historically enterprise software was constructed to automate the ERP - and then the supply chain systems extended the ERP. They were joined at the hip. In virtual enterprises, the supply chain system needs to be ERP agnostic, sitting above each of the ERPs that are distributed across the virtual enterprise - most of which are operating in other businesses. This is vital so that the supply chain system can manage the flow of material and the related information through the multiple enterprises. It has to have strong collaboration tools. It needs to be highly flexible. Users need to be able to see information that's coming from multiple sources and be able to react and respond to events across those sources.  Oracle Fusion Distributed Order Orchestration (DOO) is a perfect example of a supply chain system designed to operate in this virtual way. DOO embraces the idea that a company's fulfillment challenge is a distributed, multi-enterprise problem. It enables users to manage the process and the trading partners in a uniform way and deliver a consistent user experience while operating over a heterogeneous, virtual enterprise. This is a fundamental shift at the core of managing supply chains. It forces virtual enterprises to think architecturally about how best to construct their supply chain systems.  Case in point, almost everyone has ordered from Amazon.com at one time or another. Our orders are as likely to be fulfilled by third parties as they are by Amazon itself. To deliver the order promptly and efficiently, Amazon has to send it to the right fulfillment location and know the availability in that location. It needs to be able to track status of the fulfillment and deal with exceptions. As a virtual enterprise, Amazon's operations, using thousands of trading partners, requires a very different approach to fulfillment than the traditional 'take an order and ship it from your own warehouse' model. Amazon had no choice but to develop a complex, expensive and custom solution to tackle this problem as there used to be no product solution available. Now, other companies who want to follow similar models have a better off-the-shelf choice -- Oracle Distributed Order Orchestration (DOO).  Consider how another of our customers is using our distributed orchestration solution. This major airplane manufacturer has a highly complex business and interacts regularly with the U.S. Government and major airlines. It sits in the middle of an intricate supply chain and needed to improve visibility across its many different entities. Oracle Fusion DOO gives the company an orchestration mechanism so it could improve quality, speed, flexibility, and consistency without requiring an organ transplant of these highly complex legacy systems. Many retailers face the challenge of dealing with brick and mortar, Web, and reseller channels. They all need to be knitted together into a virtual enterprise experience that is consistent for their customers. When a large U.K. grocer with a strong brick and mortar retail operation added an online business, they turned to Oracle Fusion DOO to bring these entities together. Disturbing the Peace with Acquisitions Quite often a company's ERP system is disrupted when it acquires a new company. An acquisition can inject a new set of processes and systems -- or even introduce an entirely new business like Sun's hardware did at Oracle. This challenge has been a driver for some of our DOO customers. A large power management company is using Oracle Fusion DOO to provide the flexibility to rapidly integrate additional products and services into its central fulfillment operation. The Flip Side of Fulfillment Meanwhile, we haven't ignored similar challenges on the supply side of the equation. Specifically, how to manage complex supply in a flexible way when there are multiple trading parties involved? How to manage the supply to suppliers? How to manage critical components that need to merge in a tier two or tier three supply chain? By investing in supply orchestration solutions for the virtual enterprise, we plan to give users better visibility into their network of suppliers to help them drive down costs. We also think this technology and full orchestration process can be applied to the financial side of organizations. An example is transactions that flow through complex internal structures to minimize tax exposure. We can help companies manage those transactions effectively by thinking about the internal organization as a virtual enterprise and bringing the same solution set to this internal challenge.  The Clear Front Runner No other company is investing in solving the virtual enterprise supply chain issues like Oracle is. Oracle is in a unique position to become the gold standard in this market space. We have the infrastructure of Oracle technology. We already have an Oracle Fusion DOO application which embraces the best of what's required in this area. And we're absolutely committed to extending our Fusion solution to other use cases and delivering even more business value.

  Read the article

• Projected Results

  - by Sylvie MacKenzie, PMP

  Excerpt from PROFIT - ORACLE - by Monica Mehta Yasser Mahmud has seen a revolution in project management over the past decade. During that time, the former Primavera product strategist (who joined Oracle when his company was acquired in 2008) has not only observed a transformation in the way IT systems support corporate projects but the role project portfolio management (PPM) plays in the enterprise. “15 years ago project management was the domain of project management office (PMO),” Mahmud recalls of earlier days. “But over the course of the past decade, we've seen it transform into a mission critical enterprise discipline, that has made Primavera indispensable in the board room. Now, as a senior manager, a board member, or a C-level executive you have direct and complete visibility into what’s kind of going on in the organization—at a level of detail that you're going to consume that information.” Now serving as Oracle’s vice president of product strategy and industry marketing, Mahmud shares his thoughts on how Oracle’s Primavera solutions have evolved and how best-in-class project portfolio management systems can help businesses stay competitive. Profit: What do you feel are the market dynamics that are changing project management today? Mahmud: First, the data explosion. We're generating data at twice the rate at which we can actually store it. The same concept applies for project-intensive organizations. A lot of data is gathered, but what are we really doing with it? Are we turning data into insight? Are we using that insight and turning it into foresight with analytics tools? This is a key driver that will separate the very good companies—the very competitive companies—from those that are not as competitive. Another trend is centered on the explosion of mobile computing. By the year 2013, an estimated 35 percent of the world’s workforce is going to be mobile. That’s one billion people. So the question is not if you're going to go mobile, it’s how fast you are going to go mobile. What kind of impact does that have on how the workforce participates in projects? What worked ten to fifteen years ago is not going to work today. It requires a real rethink around the interfaces and how data is actually presented. Profit: What is the role of project management in this new landscape? Mahmud: We recently conducted a PPM study with the Economist Intelligence Unit centered to determine how important project management is considered within organizations. Our target was primarily CFOs, CIOs, and senior managers and we discovered that while 95 percent of participants believed it critical to their business, only six percent were confident that projects were delivered on time and on budget. That’s a huge gap. Most organizations are looking for efficiency, especially in these volatile financial times. But senior management can’t keep track of every project in a large organization. As a result, executives are attempting to inventory the work being conducted under their watch. What is often needed is a very high-level assessment conducted at the board level to say, “Here are the 50 initiatives that we have underway. How do they line up with our strategic drivers?” This line of questioning can provide early warning that work and strategy are out of alignment; finding the gap between what the business needs to do and the actual performance scorecard. That’s low-hanging fruit for any executive looking to increase efficiency and save money. But it can only be obtained through proper assessment of existing projects—and you need a project system of record to get that done. Over the next decade or so, project management is going to transform into holistic work management. Business leaders will want make sure key projects align with corporate strategy, but also the ability to drill down into daily activity and smaller projects to make sure they line up as well. Keeping employees from working on tasks—even for a few hours—that don’t line up with corporate goals will, in many ways, become a competitive differentiator. Profit: How do all of these market challenges and shifting trends impact Oracle’s Primavera solutions and meeting customers’ needs? Mahmud: For Primavera, it’s a transformation from being a project management application to a PPM system in the enterprise. Also making that system a mission-critical application by connecting to other key applications within the ecosystem, such as the enterprise resource planning (ERP), supply chain, and CRM systems. Analytics have also become a huge component. Business analytics have made Oracle’s Primavera applications pertinent in the boardroom. Now, as a senior manager, a board member, a CXO, CIO, or CEO, you have direct visibility into what’s going on in the organization at a level that you're able to consume that information. In addition, all of this information pairs up really well with your financials and other data. Certainly, when you're an Oracle shop, you have that visibility that you didn’t have before from a project execution perspective. Profit: What new strategies and tools are being implemented to create a more efficient workplace for users? Mahmud: We believe very strongly that just because you call something an enterprise project portfolio management system doesn’t make it so—you have to get people to want to participate in the system. This can’t be mandated down from the top. It simply doesn’t work that way. A truly adoptable solution is one that makes it super easy for all types users to participate, by providing them interfaces where they live. Keeping that in mind, a major area of development has been alternative user interfaces. This is increasingly resulting in the creation of lighter weight, targeted interfaces such as iOS applications, and smartphones interfaces such as for iPhone and Android platform. Profit: How does this translate into the development of Oracle’s Primavera solutions? Mahmud: Let me give you a few examples. We recently announced the launch of our Primavera P6 Team Member application, which is a native iOS application for the iPhone. This interface makes it easier for team members to do their jobs quickly and effectively. Similarly, we introduced the Primavera analytics application, which can be consumed via mobile devices, and when married with Oracle Spatial capabilities, users can get a geographical view of what’s going on and which projects are occurring in various locations around the world. Lastly, we introduced advanced email integration that allows project team members to status work via E-mail. This functionality leverages the fact that users are in E-mail system throughout the day and allows them to status their work without the need to launch the Primavera application. It comes back to a mantra: provide as many alternative user interfaces as possible, so you can give people the ability to work, to participate, to raise issues, to create projects, in the places where they live. Do it in such a way that it’s non-intrusive, do it in such a way that it’s easy and intuitive and they can get it done in a short amount of time. If you do that, workers can get back to doing what they're actually getting paid for.

  Read the article

• Random process hangs after clean install

  - by Toshe

  After installing fresh Kubuntu 11.04 Natty on my desktop PC, I experienced some issues with application and process hangs. There is also a problem with my USB 3 hard disk. These sort of problems did not happen on Kubuntu 10.10 installed on the same PC (on separate partition). The hangs manifest themselves with kernel log messages like these: [ 960.480151] INFO: task amarok:2505 blocked for more than 120 seconds. [ 960.480153] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 960.480155] amarok D 0000000000000000 0 2505 1 0x00000000 [ 960.480158] ffff8800a556bb38 0000000000000086 ffff8800a556bfd8 ffff8800a556a000 [ 960.480162] 0000000000013d00 ffff8800cb7f3178 ffff8800a556bfd8 0000000000013d00 [ 960.480165] ffffffff81a0b020 ffff8800cb7f2dc0 ffffea000242ac58 ffff88012704c870 [ 960.480169] Call Trace: [ 960.480172] [<ffffffff815c19f7>] __mutex_lock_slowpath+0xf7/0x180 [ 960.480175] [<ffffffff815c144b>] mutex_lock+0x2b/0x50 [ 960.480180] [<ffffffffa0d0ad42>] video_open+0x102/0x400 [cx8800] [ 960.480183] [<ffffffff815c2cbe>] ? _raw_spin_lock+0xe/0x20 [ 960.480186] [<ffffffff8117c55d>] ? __d_lookup+0x10d/0x170 [ 960.480191] [<ffffffffa0ca0731>] v4l2_open+0x101/0x130 [videodev] [ 960.480194] [<ffffffff81168f4a>] chrdev_open+0xda/0x1f0 [ 960.480197] [<ffffffff81168e70>] ? chrdev_open+0x0/0x1f0 [ 960.480200] [<ffffffff81162cee>] __dentry_open+0xce/0x2f0 [ 960.480202] [<ffffffff8116ef33>] ? generic_permission+0x23/0xc0 [ 960.480205] [<ffffffff811641e1>] nameidata_to_filp+0x71/0x80 [ 960.480208] [<ffffffff811733c8>] finish_open+0xc8/0x1b0 [ 960.480210] [<ffffffff811725b7>] ? do_path_lookup+0x87/0x160 [ 960.480213] [<ffffffff81173b88>] do_filp_open+0x2c8/0x7c0 [ 960.480216] [<ffffffff81172902>] ? user_path_at+0x62/0xa0 [ 960.480219] [<ffffffff81131d4d>] ? handle_mm_fault+0x16d/0x250 [ 960.480222] [<ffffffff812e6c47>] ? __strncpy_from_user+0x27/0x60 [ 960.480225] [<ffffffff81180ea7>] ? alloc_fd+0xf7/0x150 [ 960.480228] [<ffffffff8116425a>] do_sys_open+0x6a/0x150 [ 960.480230] [<ffffffff81164360>] sys_open+0x20/0x30 [ 960.480233] [<ffffffff8100c002>] system_call_fastpath+0x16/0x1b [ 1080.480027] INFO: task knotify4:1663 blocked for more than 120 seconds. [ 1080.480030] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1080.480032] knotify4 D 0000000000000000 0 1663 1 0x00000000 [ 1080.480036] ffff880123a2bb28 0000000000000082 ffff880123a2bfd8 ffff880123a2a000 [ 1080.480040] 0000000000013d00 ffff880121003178 ffff880123a2bfd8 0000000000013d00 [ 1080.480044] ffff8800cb7e16e0 ffff880121002dc0 ffffffff81060a27 ffff88012704c870 [ 1080.480048] Call Trace: [ 1080.480054] [<ffffffff81060a27>] ? mutex_spin_on_owner+0x97/0xd0 [ 1080.480059] [<ffffffff815c19f7>] __mutex_lock_slowpath+0xf7/0x180 [ 1080.480069] [<ffffffff812e4f61>] ? vsnprintf+0x221/0x620 [ 1080.480072] [<ffffffff815c144b>] mutex_lock+0x2b/0x50 [ 1080.480076] [<ffffffffa0b2d10f>] cx8802_request_acquire+0x5f/0xf0 [cx8802] [ 1080.480081] [<ffffffffa0e87e08>] mpeg_open+0x78/0x270 [cx88_blackbird] [ 1080.480084] [<ffffffff8117c55d>] ? __d_lookup+0x10d/0x170 [ 1080.480092] [<ffffffffa0ca0731>] v4l2_open+0x101/0x130 [videodev] [ 1080.480096] [<ffffffff81168f4a>] chrdev_open+0xda/0x1f0 [ 1080.480099] [<ffffffff81168e70>] ? chrdev_open+0x0/0x1f0 [ 1080.480102] [<ffffffff81162cee>] __dentry_open+0xce/0x2f0 [ 1080.480105] [<ffffffff8116ef33>] ? generic_permission+0x23/0xc0 [ 1080.480108] [<ffffffff811641e1>] nameidata_to_filp+0x71/0x80 [ 1080.480111] [<ffffffff811733c8>] finish_open+0xc8/0x1b0 [ 1080.480113] [<ffffffff811725b7>] ? do_path_lookup+0x87/0x160 [ 1080.480116] [<ffffffff81173b88>] do_filp_open+0x2c8/0x7c0 [ 1080.480119] [<ffffffff81172902>] ? user_path_at+0x62/0xa0 [ 1080.480122] [<ffffffff811663f1>] ? get_empty_filp+0xa1/0x170 [ 1080.480125] [<ffffffff812e6c47>] ? __strncpy_from_user+0x27/0x60 [ 1080.480128] [<ffffffff81180ea7>] ? alloc_fd+0xf7/0x150 [ 1080.480131] [<ffffffff8116425a>] do_sys_open+0x6a/0x150 [ 1080.480134] [<ffffffff81164360>] sys_open+0x20/0x30 [ 1080.480137] [<ffffffff8100c002>] system_call_fastpath+0x16/0x1b [ 1080.480147] INFO: task dolphin:1842 blocked for more than 120 seconds. [ 1080.480148] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1080.480150] dolphin D 0000000000000000 0 1842 1 0x00000004 [ 1080.480154] ffff8800cb4f3b38 0000000000000082 ffff8800cb4f3fd8 ffff8800cb4f2000 [ 1080.480157] 0000000000013d00 ffff8800cb7f4858 ffff8800cb4f3fd8 0000000000013d00 [ 1080.480161] ffffffff81a0b020 ffff8800cb7f44a0 ffffea000267b0d0 ffff88012704c870 [ 1080.480164] Call Trace: [ 1080.480168] [<ffffffff815c19f7>] __mutex_lock_slowpath+0xf7/0x180 [ 1080.480171] [<ffffffff815c144b>] mutex_lock+0x2b/0x50 [ 1080.480176] [<ffffffffa0d0ad42>] video_open+0x102/0x400 [cx8800] [ 1080.480179] [<ffffffff815c2cbe>] ? _raw_spin_lock+0xe/0x20 [ 1080.480181] [<ffffffff8117c55d>] ? __d_lookup+0x10d/0x170 [ 1080.480186] [<ffffffffa0ca0731>] v4l2_open+0x101/0x130 [videodev] [ 1080.480190] [<ffffffff81168f4a>] chrdev_open+0xda/0x1f0 [ 1080.480192] [<ffffffff81168e70>] ? chrdev_open+0x0/0x1f0 [ 1080.480195] [<ffffffff81162cee>] __dentry_open+0xce/0x2f0 [ 1080.480198] [<ffffffff8116ef33>] ? generic_permission+0x23/0xc0 [ 1080.480200] [<ffffffff811641e1>] nameidata_to_filp+0x71/0x80 [ 1080.480203] [<ffffffff811733c8>] finish_open+0xc8/0x1b0 [ 1080.480206] [<ffffffff811725b7>] ? do_path_lookup+0x87/0x160 [ 1080.480208] [<ffffffff81173b88>] do_filp_open+0x2c8/0x7c0 [ 1080.480211] [<ffffffff81172902>] ? user_path_at+0x62/0xa0 [ 1080.480214] [<ffffffff81131d4d>] ? handle_mm_fault+0x16d/0x250 [ 1080.480217] [<ffffffff812e6c47>] ? __strncpy_from_user+0x27/0x60 [ 1080.480220] [<ffffffff81180ea7>] ? alloc_fd+0xf7/0x150 [ 1080.480223] [<ffffffff8116425a>] do_sys_open+0x6a/0x150 [ 1080.480225] [<ffffffff81164360>] sys_open+0x20/0x30 [ 1080.480228] [<ffffffff8100c002>] system_call_fastpath+0x16/0x1b Attempts to kill the hung process are unsuccessful: root@deskpc:~# ps -ef |grep amarok myuser 2505 1 0 10:47 ? 00:00:00 /usr/bin/amarok root 2747 2020 0 11:06 pts/3 00:00:00 grep --color=auto amarok root@deskpc:~# kill -9 2505 root@deskpc:~# ps -ef |grep amarok myuser 2505 1 0 10:47 ? 00:00:00 /usr/bin/amarok root 2749 2020 0 11:06 pts/3 00:00:00 grep --color=auto amarok root@deskpc:~# kill -9 2505 root@deskpc:~# ps -ef |grep amarok myuser 2505 1 0 10:47 ? 00:00:00 /usr/bin/amarok root 2751 2020 0 11:06 pts/3 00:00:00 grep --color=auto amarok root@deskpc:~# When trying to access my external USB3 disk, the following kernel message is observed: [ 2169.330012] xhci_hcd 0000:06:00.0: Timeout while waiting for a slot [ 2169.330018] hub 3-0:1.0: couldn't allocate port 1 usb_device I am not sure the two problems (application hangs and USB3 timeouts are related) but they do not happen under Kubuntu 10.10. Judging by the dmesg messages, it looks to me that this is a kernel (or potentially kernel driver) problem, but not sure how to debug it. Any ideas? I ran apport-bug, but it advised me to post a question here first. Shall I report the issue on the official K/Ubuntu bugzilla?

  Read the article

• PASS: SQLRally Thoughts

  - by Bill Graziano

  The PASS Board recently decided that we wouldn’t put another US-based SQLRally on the calendar until we had a chance to review the program. I wanted to provide some of my thinking around this. Keep in mind that this is the opinion of one Board member. The Board committed to complete two SQLRally events to determine if an event modeled between SQL Saturday and the Summit was viable. We’ve completed the two events and now it’s time to step back and review the program. This is my seventh year on the PASS Board. Over that time people have asked me why PASS does certain things. Many, many times my answer has been “Because that’s the way we did it last year”. And I am tired of giving that answer. We need to take a step back and review the US-based SQLRally before we schedule another one. It would be irresponsible for me as a Board member to commit resources to this without validating that what we’re doing makes sense for the organization and our members. I have no doubt that this was a great event for the attendees. We just need to validate it’s the best use of our resources. Please keep in mind that we haven’t cancelled the event. We’ve just said we need to review it before scheduling another one. My opinion is that some fairly serious changes are needed to the model before we consider it again – IF we do it again. I’ve come to that conclusion after speaking with the Dallas organizers, our HQ team, our Marketing team, other Board members (including one of the Orlando organizers), attendees in Orlando and Dallas and visiting other similar events. I should point out that their views aren’t unanimous on nearly any part of this event -- which is one of the reasons I want to take some time and think about this before continuing. I think it’s helpful to look at the original goals of what we were trying to accomplish. Andy Warren wrote these up in August of 2010. My summary of these goals and some thoughts on each one is below. Many of these thoughts revolve around the growth of SQL Saturdays. In the two years since that document was written these events have grown significantly. The largest SQL Saturdays are now over 500 people which mean they are nearly the same size as our recent SQLRally. Our goals included: Geographic diversity. We wanted an event in an area of the country that was away from any given Summit location. I think that’s still a valid goal. But we also have SQL Saturdays all over the country. What does SQLRally bring to this that SQLSaturday doesn’t? Speaker growth. One of the stated goals was to build a “farm club” for speakers. This gives us a way for speakers to work up to speaking at Summit by speaking in front of larger crowds. What does SQLRally bring to this that the larger SQL Saturdays aren’t providing? Pre-Conference speakers is one obvious answer here. Lower price. On a per-day basis, SQLRally is roughly 1/4th the price of the Summit. We wanted a way for people to experience something Summit-like at a lower price point. The challenge is that we are very budget constrained at that lower price point. International Event Model.  (I need to write more about this but I’m out of time.  I’ll cover it in the next installment.) There are a number of things I really like about SQLRally. I love the smaller conferences. They give me a chance to meet more people than at something the size of Summit. I like the two day format. That gives you two evenings to be at social events with people. Seeing someone a second day is a great way to build a bond with that person. That’s more difficult to do at a SQL Saturday. We also need to talk about the financial aspects of the event. Last year generated a small $17,000 profit on revenues of $200,000. Percentage-wise that’s reasonable but on an absolute basis it’s not a huge amount in our budget. We think this year will lose between $30,000 and $50,000 and take roughly 1,000 hours of HQ time. We don’t have detailed financials back yet but that’s our best guess at this point. Part of that was driven by using a convention center instead of a hotel. Until we get detailed financials back we won’t have the full picture around the financial impact. This event also takes time and mindshare from our Marketing team. This may sound like a small thing but please don’t underestimate it. Our original vision for this was something that would take very little time from our Marketing team and just a few mentions in the Connector. It turned out to need more than that. And all those mentions and emails take up space we could use to talk about other events and other programs. Last I wanted to talk about some of the things I’m thinking about. I don’t think it’s as simple as saying if we just fix “X” it all gets better. Is this that much better of an event than SQL Saturdays? What if we gave a few SQL Saturdays some extra resources? When SQL Saturdays were around 250 people that wasn’t as viable. With some of those events over 500 we need to reconsider this. We need to get back to a hotel venue. That will help with cost and networking. Is this the best use of the 1,000 HQ hours that we invested in the event? Is our price-point correct? I’m leaning toward raising our price closer to Summit on a per-day basis. I think this will let us put on a higher quality event and alleviate much of the budget pressure. Should growing speakers be a focus? Having top-line pre-conference speakers helps market the event. It will also have an impact on pricing and overall profit. We should also ask if it actually does grow speakers. How many of these people will eventually register for Summit? Attend chapters? Is SQLRally a driver into PASS or is it something that chapters, etc. drive people to? Should we have one paid day and one free instead of two paid days? This is a very interesting model that is used by SQLBits in the UK. This gives you the two day aspect as well as offering options for paid and free attendees. I’m very intrigued by this. Should we focus on a topic? Buried in the minutes is a discussion of whether PASS should have a Business Analytics conference separate from Summit. This is an interesting question to consider. Would making SQLRally be focused on a particular topic make it more attractive? Would that even be a SQLRally? Can PASS effectively manage the two events? (FYI - Probably not.) Would it help differentiate it from Summit and SQL Saturday? These are all questions that I think should be asked and answered before we do this event again. And we can’t do that if we don’t take time to have the discussion. I wanted to get this published before I take off for a few days of vacation. When I get back I’d like to write more about why the international events are different and talk about where we go from here.

  Read the article

• Data Source Connection Pool Sizing

  - by Steve Felts

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} One of the most time-consuming procedures of a database application is establishing a connection. The connection pooling of the data source can be used to minimize this overhead.  That argues for using the data source instead of accessing the database driver directly. Configuring the size of the pool in the data source is somewhere between an art and science – this article will try to move it closer to science.  From the beginning, WLS data source has had an initial capacity and a maximum capacity configuration values.  When the system starts up and when it shrinks, initial capacity is used.  The pool can grow to maximum capacity.  Customers found that they might want to set the initial capacity to 0 (more on that later) but didn’t want the pool to shrink to 0.  In WLS 10.3.6, we added minimum capacity to specify the lower limit to which a pool will shrink.  If minimum capacity is not set, it defaults to the initial capacity for upward compatibility.   We also did some work on the shrinking in release 10.3.4 to reduce thrashing; the algorithm that used to shrink to the maximum of the currently used connections or the initial capacity (basically the unused connections were all released) was changed to shrink by half of the unused connections. The simple approach to sizing the pool is to set the initial/minimum capacity to the maximum capacity.  Doing this creates all connections at startup, avoiding creating connections on demand and the pool is stable.  However, there are a number of reasons not to take this simple approach. When WLS is booted, the deployment of the data source includes synchronously creating the connections.  The more connections that are configured in initial capacity, the longer the boot time for WLS (there have been several projects for parallel boot in WLS but none that are available).  Related to creating a lot of connections at boot time is the problem of logon storms (the database gets too much work at one time).   WLS has a solution for that by setting the login delay seconds on the pool but that also increases the boot time. There are a number of cases where it is desirable to set the initial capacity to 0.  By doing that, the overhead of creating connections is deferred out of the boot and the database doesn’t need to be available.  An application may not want WLS to automatically connect to the database until it is actually needed, such as for some code/warm failover configurations. There are a number of cases where minimum capacity should be less than maximum capacity.  Connections are generally expensive to keep around.  They cause state to be kept on both the client and the server, and the state on the backend may be heavy (for example, a process).  Depending on the vendor, connection usage may cost money.  If work load is not constant, then database connections can be freed up by shrinking the pool when connections are not in use.  When using Active GridLink, connections can be created as needed according to runtime load balancing (RLB) percentages instead of by connection load balancing (CLB) during data source deployment. Shrinking is an effective technique for clearing the pool when connections are not in use.  In addition to the obvious reason that there times where the workload is lighter,  there are some configurations where the database and/or firewall conspire to make long-unused or too-old connections no longer viable.  There are also some data source features where the connection has state and cannot be used again unless the state matches the request.  Examples of this are identity based pooling where the connection has a particular owner and XA affinity where the connection is associated with a particular RAC node.  At this point, WLS does not re-purpose (discard/replace) connections and shrinking is a way to get rid of the unused existing connection and get a new one with the correct state when needed. So far, the discussion has focused on the relationship of initial, minimum, and maximum capacity.  Computing the maximum size requires some knowledge about the application and the current number of simultaneously active users, web sessions, batch programs, or whatever access patterns are common.  The applications should be written to only reserve and close connections as needed but multiple statements, if needed, should be done in one reservation (don’t get/close more often than necessary).  This means that the size of the pool is likely to be significantly smaller then the number of users.   If possible, you can pick a size and see how it performs under simulated or real load.  There is a high-water mark statistic (ActiveConnectionsHighCount) that tracks the maximum connections concurrently used.  In general, you want the size to be big enough so that you never run out of connections but no bigger.   It will need to deal with spikes in usage, which is where shrinking after the spike is important.  Of course, the database capacity also has a big influence on the decision since it’s important not to overload the database machine.  Planning also needs to happen if you are running in a Multi-Data Source or Active GridLink configuration and expect that the remaining nodes will take over the connections when one of the nodes in the cluster goes down.  For XA affinity, additional headroom is also recommended.  In summary, setting initial and maximum capacity to be the same may be simple but there are many other factors that may be important in making the decision about sizing.

  Read the article

• Use Glassfish JMS from remote client

  - by James

  Hi, I have glassfish installed on a server with a JMS ConnectionFactory set up jms/MyConnectionFactory with a resource type or javax.jms.ConnectionFactory. I now want to access this from a client application on my local machine for this I have the following: public static void main(String[] args) { try{ Properties env = new Properties(); env.setProperty("java.naming.factory.initial", "com.sun.enterprise.naming.SerialInitContextFactory"); env.setProperty("java.naming.factory.url.pkgs", "com.sun.enterprise.naming"); env.setProperty("java.naming.factory.state", "com.sun.corba.ee.impl.presentation.rmi.JNDIStateFactoryImpl"); env.setProperty("org.omg.CORBA.ORBInitialHost", "10.97.3.74"); env.setProperty("org.omg.CORBA.ORBInitialPort", "3700"); InitialContext initialContext = new InitialContext(env); ConnectionFactory connectionFactory = null; try { connectionFactory = (ConnectionFactory) initialContext.lookup("jms/MyConnectionFactory"); } catch (Exception e) { System.out.println("JNDI API lookup failed: " + e.toString()); e.printStackTrace(); System.exit(1); } }catch(Exception e){ e.printStackTrace(System.err); } } When I run my client I get the following output: INFO: Using com.sun.enterprise.transaction.jts.JavaEETransactionManagerJTSDelegate as the delegate {org.omg.CORBA.ORBInitialPort=3700, java.naming.factory.initial=com.sun.enterprise.naming.SerialInitContextFactory, org.omg.CORBA.ORBInitialHost=10.97.3.74, java.naming.factory.state=com.sun.corba.ee.impl.presentation.rmi.JNDIStateFactoryImpl, java.naming.factory.url.pkgs=com.sun.enterprise.naming} 19-Mar-2010 16:09:13 org.hibernate.validator.util.Version <clinit> INFO: Hibernate Validator bean-validator-3.0-JBoss-4.0.2 19-Mar-2010 16:09:13 org.hibernate.validator.engine.resolver.DefaultTraversableResolver detectJPA INFO: Instantiated an instance of org.hibernate.validator.engine.resolver.JPATraversableResolver. 19-Mar-2010 16:09:13 com.sun.messaging.jms.ra.ResourceAdapter start INFO: MQJMSRA_RA1101: SJSMQ JMS Resource Adapter starting: REMOTE 19-Mar-2010 16:09:13 com.sun.messaging.jms.ra.ResourceAdapter start INFO: MQJMSRA_RA1101: SJSMQ JMSRA Started:REMOTE 19-Mar-2010 16:09:13 com.sun.enterprise.naming.impl.SerialContext lookup SEVERE: enterprise_naming.serialctx_communication_exception 19-Mar-2010 16:09:13 com.sun.enterprise.naming.impl.SerialContext lookup SEVERE: java.lang.RuntimeException: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory at com.sun.enterprise.resource.naming.ConnectorObjectFactory.getObjectInstance(ConnectorObjectFactory.java:159) at javax.naming.spi.NamingManager.getObjectInstance(NamingManager.java:304) at com.sun.enterprise.naming.impl.SerialContext.getObjectInstance(SerialContext.java:472) at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:437) at javax.naming.InitialContext.lookup(InitialContext.java:392) at simpleproducerclient.Main.main(Main.java:89) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.glassfish.appclient.client.acc.AppClientContainer.launch(AppClientContainer.java:424) at org.glassfish.appclient.client.AppClientFacade.main(AppClientFacade.java:134) Caused by: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.obtainManagedConnectionFactory(ConnectorConnectionPoolAdminServiceImpl.java:1017) at com.sun.enterprise.connectors.ConnectorRuntime.obtainManagedConnectionFactory(ConnectorRuntime.java:375) at com.sun.enterprise.resource.naming.ConnectorObjectFactory.getObjectInstance(ConnectorObjectFactory.java:124) ... 11 more Caused by: javax.naming.NamingException: Lookup failed for '__SYSTEM/pools/jms/MyConnectionFactory' in SerialContext targetHost=localhost,targetPort=3700,orb'sInitialHost=ithfdv01,orb'sInitialPort=3700 [Root exception is javax.naming.NameNotFoundException: pools] at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:442) at javax.naming.InitialContext.lookup(InitialContext.java:392) at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.getConnectorConnectionPool(ConnectorConnectionPoolAdminServiceImpl.java:804) at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.obtainManagedConnectionFactory(ConnectorConnectionPoolAdminServiceImpl.java:932) ... 13 more Caused by: javax.naming.NameNotFoundException: pools at com.sun.enterprise.naming.impl.TransientContext.resolveContext(TransientContext.java:252) at com.sun.enterprise.naming.impl.TransientContext.lookup(TransientContext.java:171) at com.sun.enterprise.naming.impl.TransientContext.lookup(TransientContext.java:172) at com.sun.enterprise.naming.impl.SerialContextProviderImpl.lookup(SerialContextProviderImpl.java:58) at com.sun.enterprise.naming.impl.RemoteSerialContextProviderImpl.lookup(RemoteSerialContextProviderImpl.java:89) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at com.sun.corba.ee.impl.presentation.rmi.ReflectiveTie.dispatchToMethod(ReflectiveTie.java:146) at com.sun.corba.ee.impl.presentation.rmi.ReflectiveTie._invoke(ReflectiveTie.java:176) at com.sun.corba.ee.impl.protocol.CorbaServerRequestDispatcherImpl.dispatchToServant(CorbaServerRequestDispatcherImpl.java:682) at com.sun.corba.ee.impl.protocol.CorbaServerRequestDispatcherImpl.dispatch(CorbaServerRequestDispatcherImpl.java:216) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequestRequest(CorbaMessageMediatorImpl.java:1841) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequest(CorbaMessageMediatorImpl.java:1695) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleInput(CorbaMessageMediatorImpl.java:1078) at com.sun.corba.ee.impl.protocol.giopmsgheaders.RequestMessage_1_2.callback(RequestMessage_1_2.java:221) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequest(CorbaMessageMediatorImpl.java:797) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.dispatch(CorbaMessageMediatorImpl.java:561) JNDI API lookup failed: javax.naming.CommunicationException: Communication exception for SerialContext targetHost=10.97.3.74,targetPort=3700,orb'sInitialHost=ithfdv01,orb'sInitialPort=3700 [Root exception is java.lang.RuntimeException: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory] at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.doWork(CorbaMessageMediatorImpl.java:2558) at com.sun.corba.ee.impl.orbutil.threadpool.ThreadPoolImpl$WorkerThread.performWork(ThreadPoolImpl.java:492) at com.sun.corba.ee.impl.orbutil.threadpool.ThreadPoolImpl$WorkerThread.run(ThreadPoolImpl.java:528) javax.naming.CommunicationException: Communication exception for SerialContext targetHost=10.97.3.74,targetPort=3700,orb'sInitialHost=ithfdv01,orb'sInitialPort=3700 [Root exception is java.lang.RuntimeException: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory] at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:461) at javax.naming.InitialContext.lookup(InitialContext.java:392) at simpleproducerclient.Main.main(Main.java:89) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.glassfish.appclient.client.acc.AppClientContainer.launch(AppClientContainer.java:424) at org.glassfish.appclient.client.AppClientFacade.main(AppClientFacade.java:134) Caused by: java.lang.RuntimeException: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory at com.sun.enterprise.resource.naming.ConnectorObjectFactory.getObjectInstance(ConnectorObjectFactory.java:159) at javax.naming.spi.NamingManager.getObjectInstance(NamingManager.java:304) at com.sun.enterprise.naming.impl.SerialContext.getObjectInstance(SerialContext.java:472) at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:437) ... 8 more Caused by: com.sun.appserv.connectors.internal.api.ConnectorRuntimeException: This pool is not bound in JNDI : jms/MyConnectionFactory at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.obtainManagedConnectionFactory(ConnectorConnectionPoolAdminServiceImpl.java:1017) at com.sun.enterprise.connectors.ConnectorRuntime.obtainManagedConnectionFactory(ConnectorRuntime.java:375) at com.sun.enterprise.resource.naming.ConnectorObjectFactory.getObjectInstance(ConnectorObjectFactory.java:124) ... 11 more Caused by: javax.naming.NamingException: Lookup failed for '__SYSTEM/pools/jms/MyConnectionFactory' in SerialContext targetHost=localhost,targetPort=3700,orb'sInitialHost=ithfdv01,orb'sInitialPort=3700 [Root exception is javax.naming.NameNotFoundException: pools] at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:442) at javax.naming.InitialContext.lookup(InitialContext.java:392) at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.getConnectorConnectionPool(ConnectorConnectionPoolAdminServiceImpl.java:804) at com.sun.enterprise.connectors.service.ConnectorConnectionPoolAdminServiceImpl.obtainManagedConnectionFactory(ConnectorConnectionPoolAdminServiceImpl.java:932) ... 13 more Caused by: javax.naming.NameNotFoundException: pools at com.sun.enterprise.naming.impl.TransientContext.resolveContext(TransientContext.java:252) at com.sun.enterprise.naming.impl.TransientContext.lookup(TransientContext.java:171) at com.sun.enterprise.naming.impl.TransientContext.lookup(TransientContext.java:172) at com.sun.enterprise.naming.impl.SerialContextProviderImpl.lookup(SerialContextProviderImpl.java:58) at com.sun.enterprise.naming.impl.RemoteSerialContextProviderImpl.lookup(RemoteSerialContextProviderImpl.java:89) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at com.sun.corba.ee.impl.presentation.rmi.ReflectiveTie.dispatchToMethod(ReflectiveTie.java:146) at com.sun.corba.ee.impl.presentation.rmi.ReflectiveTie._invoke(ReflectiveTie.java:176) at com.sun.corba.ee.impl.protocol.CorbaServerRequestDispatcherImpl.dispatchToServant(CorbaServerRequestDispatcherImpl.java:682) at com.sun.corba.ee.impl.protocol.CorbaServerRequestDispatcherImpl.dispatch(CorbaServerRequestDispatcherImpl.java:216) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequestRequest(CorbaMessageMediatorImpl.java:1841) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequest(CorbaMessageMediatorImpl.java:1695) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleInput(CorbaMessageMediatorImpl.java:1078) at com.sun.corba.ee.impl.protocol.giopmsgheaders.RequestMessage_1_2.callback(RequestMessage_1_2.java:221) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.handleRequest(CorbaMessageMediatorImpl.java:797) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.dispatch(CorbaMessageMediatorImpl.java:561) at com.sun.corba.ee.impl.protocol.CorbaMessageMediatorImpl.doWork(CorbaMessageMediatorImpl.java:2558) at com.sun.corba.ee.impl.orbutil.threadpool.ThreadPoolImpl$WorkerThread.performWork(ThreadPoolImpl.java:492) at com.sun.corba.ee.impl.orbutil.threadpool.ThreadPoolImpl$WorkerThread.run(ThreadPoolImpl.java:528) I have looked at a number of posts and have tried a number of things with no success. I can run the following commands on my server: ./asadmin list-jndi-entries UserTransaction: com.sun.enterprise.transaction.TransactionNamingProxy$UserTransactionProxy java:global: com.sun.enterprise.naming.impl.TransientContext jdbc: com.sun.enterprise.naming.impl.TransientContext ejb: com.sun.enterprise.naming.impl.TransientContext com.sun.enterprise.container.common.spi.util.InjectionManager: com.sun.enterprise.container.common.impl.util.InjectionManagerImpl jms: com.sun.enterprise.naming.impl.TransientContext Command list-jndi-entries executed successfully. ./asadmin list-jndi-entries --context jms MyTopic: org.glassfish.javaee.services.ResourceProxy MyConnectionFactory: org.glassfish.javaee.services.ResourceProxy MyQueue: org.glassfish.javaee.services.ResourceProxy Command list-jndi-entries executed successfully. Any help is greatly appreciated. Cheers, James

  Read the article

• Spring Security Configuration Leads to Perpetual Authentication Request

  - by Sammy

  Hello, I have configured my web application with the following config file: <beans xmlns="http://www.springframework.org/schema/beans" xmlns:security="http://www.springframework.org/schema/security" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans.xsd http://www.springframework.org/schema/security http://www.springframework.org/schema/security/spring-security-3.0.xsd"> <security:global-method-security secured-annotations="enabled" pre-post-annotations="enabled" /> <!-- Filter chain; this is referred to from the web.xml file. Each filter is defined and configured as a bean later on. --> <!-- Note: anonumousProcessingFilter removed. --> <bean id="filterChainProxy" class="org.springframework.security.web.FilterChainProxy"> <security:filter-chain-map path-type="ant"> <security:filter-chain pattern="/**" filters="securityContextPersistenceFilter, basicAuthenticationFilter, exceptionTranslationFilter, filterSecurityInterceptor" /> </security:filter-chain-map> </bean> <!-- This filter is responsible for session management, or rather the lack thereof. --> <bean id="securityContextPersistenceFilter" class="org.springframework.security.web.context.SecurityContextPersistenceFilter"> <property name="securityContextRepository"> <bean class="org.springframework.security.web.context.HttpSessionSecurityContextRepository"> <property name="allowSessionCreation" value="false" /> </bean> </property> </bean> <!-- Basic authentication filter. --> <bean id="basicAuthenticationFilter" class="org.springframework.security.web.authentication.www.BasicAuthenticationFilter"> <property name="authenticationManager" ref="authenticationManager" /> <property name="authenticationEntryPoint" ref="authenticationEntryPoint" /> </bean> <!-- Basic authentication entry point. --> <bean id="authenticationEntryPoint" class="org.springframework.security.web.authentication.www.BasicAuthenticationEntryPoint"> <property name="realmName" value="Ayudo Web Service" /> </bean> <!-- An anonymous authentication filter, which is chained after the normal authentication mechanisms and automatically adds an AnonymousAuthenticationToken to the SecurityContextHolder if there is no existing Authentication held there. --> <!-- <bean id="anonymousProcessingFilter" class="org.springframework.security.web.authentication.AnonymousProcessingFilter"> <property name="key" value="ayudo" /> <property name="userAttribute" value="anonymousUser, ROLE_ANONYMOUS" /> </bean> --> <!-- Authentication manager that chains our main authentication provider and anonymous authentication provider. --> <bean id="authenticationManager" class="org.springframework.security.authentication.ProviderManager"> <property name="providers"> <list> <ref local="daoAuthenticationProvider" /> <ref local="inMemoryAuthenticationProvider" /> <!-- <ref local="anonymousAuthenticationProvider" /> --> </list> </property> </bean> <!-- Main authentication provider; in this case, memory implementation. --> <bean id="inMemoryAuthenticationProvider" class="org.springframework.security.authentication.dao.DaoAuthenticationProvider"> <property name="userDetailsService" ref="propertiesUserDetails" /> </bean> <security:user-service id="propertiesUserDetails" properties="classpath:operators.properties" /> <!-- Main authentication provider. --> <bean id="daoAuthenticationProvider" class="org.springframework.security.authentication.dao.DaoAuthenticationProvider"> <property name="userDetailsService" ref="userDetailsService" /> </bean> <!-- An anonymous authentication provider which is chained into the ProviderManager so that AnonymousAuthenticationTokens are accepted. --> <!-- <bean id="anonymousAuthenticationProvider" class="org.springframework.security.authentication.AnonymousAuthenticationProvider"> <property name="key" value="ayudo" /> </bean> --> <bean id="userDetailsService" class="org.springframework.security.core.userdetails.jdbc.JdbcDaoImpl"> <property name="dataSource" ref="dataSource" /> </bean> <bean id="exceptionTranslationFilter" class="org.springframework.security.web.access.ExceptionTranslationFilter"> <property name="authenticationEntryPoint" ref="authenticationEntryPoint" /> <property name="accessDeniedHandler"> <bean class="org.springframework.security.web.access.AccessDeniedHandlerImpl" /> </property> </bean> <bean id="filterSecurityInterceptor" class="org.springframework.security.web.access.intercept.FilterSecurityInterceptor"> <property name="securityMetadataSource"> <security:filter-security-metadata-source use-expressions="true"> <security:intercept-url pattern="/*.html" access="permitAll" /> <security:intercept-url pattern="/version" access="permitAll" /> <security:intercept-url pattern="/users/activate" access="permitAll" /> <security:intercept-url pattern="/**" access="isAuthenticated()" /> </security:filter-security-metadata-source> </property> <property name="authenticationManager" ref="authenticationManager" /> <property name="accessDecisionManager" ref="accessDecisionManager" /> </bean> <bean id="accessDecisionManager" class="org.springframework.security.access.vote.AffirmativeBased"> <property name="decisionVoters"> <list> <bean class="org.springframework.security.access.vote.RoleVoter" /> <bean class="org.springframework.security.web.access.expression.WebExpressionVoter" /> </list> </property> </bean> As soon as I run my application on tomcat, I get a request for username/password basic authentication dialog. Even when I try to access: localhost:8080/myapp/version, which is explicitly set to permitAll, I get the authentication request dialog. Help! Thank, Sammy

  Read the article

• Spring & hibernate configuration (using maven): java.lang.ClassNotFoundException: org.hibernate.cfg.

  - by Marcos Carceles

  Hi, I am trying to include spring and hibernate in an application running on a Weblogic 10.3 server. When I run the application in the server, while accessing an TestServlet to check my configuration I get the following exception: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'mySessionFactory' defined in class path resource [spring-config/HorizonModelPeopleConnectionsSpringContext.xml]: Instantiation of bean failed; nested exception is org.springframework.beans.BeanInstantiationException: Could not instantiate bean class [org.springframework.orm.hibernate3.LocalSessionFactoryBean]: Constructor threw exception; nested exception is java.lang.NoClassDefFoundError: org.hibernate.cfg.Configuration at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:448) at org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:251) at org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:156) at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:248) at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:160) at org.springframework.beans.factory.support.DefaultListableBeanFactory.preInstantiateSingletons(DefaultListableBeanFactory.java:284) at org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:352) at org.springframework.context.support.ClassPathXmlApplicationContext.(ClassPathXmlApplicationContext.java:91) at org.springframework.context.support.ClassPathXmlApplicationContext.(ClassPathXmlApplicationContext.java:75) at org.springframework.context.support.ClassPathXmlApplicationContext.(ClassPathXmlApplicationContext.java:65) at view.com.horizon.test.SpringHibernateServlet.doGet(SpringHibernateServlet.java:27) at javax.servlet.http.HttpServlet.service(HttpServlet.java:707) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292) at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.security.wls.filter.SSOSessionSynchronizationFilter.doFilter(SSOSessionSynchronizationFilter.java:279) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.dms.wls.DMSServletFilter.doFilter(DMSServletFilter.java:326) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3592) at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321) at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121) at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2202) at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2108) at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1432) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) Caused by: org.springframework.beans.BeanInstantiationException: Could not instantiate bean class [org.springframework.orm.hibernate3.LocalSessionFactoryBean]: Constructor threw exception; nested exception is java.lang.NoClassDefFoundError: org.hibernate.cfg.Configuration at org.springframework.beans.BeanUtils.instantiateClass(BeanUtils.java:100) at org.springframework.beans.factory.support.SimpleInstantiationStrategy.instantiate(SimpleInstantiationStrategy.java:61) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.instantiateBean(AbstractAutowireCapableBeanFactory.java:756) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBeanInstance(AbstractAutowireCapableBeanFactory.java:721) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:384) ... 31 more Caused by: java.lang.NoClassDefFoundError: org.hibernate.cfg.Configuration at org.springframework.orm.hibernate3.LocalSessionFactoryBean.class$(LocalSessionFactoryBean.java:158) at org.springframework.orm.hibernate3.LocalSessionFactoryBean.(LocalSessionFactoryBean.java:158) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at org.springframework.beans.BeanUtils.instantiateClass(BeanUtils.java:85) ... 35 more I have checked my application and the hibernate jar file is included and it contains the class it says its missing: org.hibernate.cfg.Configuration. The application is built with maven. These are the dependencies of the JAR file using spring and hibernate: <!-- Frameworks --> <!-- Hibernate framework --> <dependency> <groupId>org.hibernate</groupId> <artifactId>hibernate</artifactId> <version>3.2.7.ga</version> </dependency> <!-- Hibernate uses slf4j for logging, for our purposes here use the simple backend --> <dependency> <groupId>org.slf4j</groupId> <artifactId>slf4j-log4j12</artifactId> <version>1.5.2</version> </dependency> <!-- Hibernate gives you a choice of bytecode providers between cglib and javassist --> <dependency> <groupId>javassist</groupId> <artifactId>javassist</artifactId> <version>3.4.GA</version> </dependency> <!-- Spring framework --> <dependency> <groupId>org.springframework</groupId> <artifactId>spring-orm</artifactId> <version>2.5.6</version> </dependency> At first I thought it could be an issue with the versions in the spring and hibernate libraries, so I have tried with different ones, but still I couldn't find anywhere where it says which library versions are compatible,. just got that Spring 2.5.x needs hibernate =3.1 And this is my Spring config file: <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd"> <bean id="myDataSource" class="org.springframework.jndi.JndiObjectFactoryBean"> <property name="jndiName"> <value>jdbc/WebCenterDS</value> </property> <!--property name="resourceRef"> <value>true</value> </property> <property name="jndiEnvironment"> <props> <prop key="java.naming.factory.initial">weblogic.jndi.WLInitialContextFactory</prop> <prop key="java.naming.provider.url">t3://localhost:7001</prop> </props> </property--> </bean> <bean id="mySessionFactory" class="org.springframework.orm.hibernate3.LocalSessionFactoryBean"> <property name="dataSource" ref="myDataSource"/> <property name="configLocation"> <value>classpath:hibernate-config/hibernate.cfg.xml</value> </property> <property name="mappingResources"> <list> <value>classpath:com/horizon/model/peopleconnections/profile/internal/bean/CustomAttribute.hbm.xml</value> </list> </property> <property name="hibernateProperties"> <value>hibernate.dialect=org.hibernate.dialect.HSQLDialect</value> </property> </bean> <bean id="profileExtensionDAO" class="com.horizon.model.peopleconnections.profile.internal.dao.ProfileExtensionDAOImpl"> <property name="sessionFactory" ref="mySessionFactory"/> </bean> </beans> The WAR structure I get is the following: J2EETestApplication ¦ springhibernate.jsp ¦ +---WEB-INF ¦ faces-config.xml ¦ web.xml ¦ weblogic.xml ¦ +---classes ¦ +---view ¦ +---com ¦ +---horizon ¦ +---test ¦ SpringHibernateServlet.class ¦ +---lib activation-1.1.jar antlr-2.7.6.jar aopalliance-1.0.jar asm-1.5.3.jar asm-attrs-1.5.3.jar cglib-2.1_3.jar commons-codec-1.3.jar commons-collections-2.1.1.jar commons-logging-1.1.1.jar dom4j-1.6.1.jar ehcache-1.2.3.jar hibernate-3.2.7.ga.jar horizon-model-commons-1.0-SNAPSHOT.jar horizon-model-peopleconnections-1.0-SNAPSHOT.jar horizon-shared-commons-1.0-SNAPSHOT.jar horizon-shared-logging-1.0-SNAPSHOT.jar horizon-shared-util-1.0-SNAPSHOT.jar horizon-shared-webcenter-1.0-SNAPSHOT.jar horizon-shared-webcenter.jar httpclient-4.0.1.jar httpcore-4.0.1.jar javassist-3.4.GA.jar jta-1.0.1B.jar log4j-1.2.14.jar mail-1.4.1.jar peopleconnections-profile-model-11.1.1.2.0.jar saxon-9.1.0.8.jar serviceframework-11.1.1.2.0.jar slf4j-api-1.5.2.jar slf4j-log4j12-1.5.2.jar spring-beans-2.5.6.jar spring-context-2.5.6.jar spring-core-2.5.6.jar spring-orm-2.5.6.jar spring-tx-2.5.6.jar Is there any dependency or configuration I am missing? If I use hibernate without spring I don't get the ClassDefNotFoundException.

  Read the article

• WebLogic job scheduling

  - by XpiritO

  Hello, overflowers :) I'm trying to implement a WebLogic job scheduling example, to test my cluster capabilities of fail-over on scheduled tasks (to ensure that these tasks are executed on fail over scenario). With this in mind, I've been following this example and trying to configure everything accordingly. Here are the steps I've done so far: Configured a cluster with 1 admin server (AdminServer) and 2 managed instances (Noddy and Snoopy); Set up database tables (using Oracle XE): ACTIVE and WEBLOGIC_TIMERS; Set up data source to access DB and associated it to the scheduling tasks under "Settings for cluster" "Scheduling"; Implemented a job (TimerListener) and a servlet to initialize the job scheduling, as follows: . package timedexecution; import java.io.IOException; import java.io.PrintWriter; import java.io.Serializable; import java.text.SimpleDateFormat; import java.util.Date; import javax.naming.InitialContext; import javax.naming.NamingException; import javax.servlet.ServletException; import javax.servlet.http.HttpServlet; import javax.servlet.http.HttpServletRequest; import javax.servlet.http.HttpServletResponse; import commonj.timers.Timer; import commonj.timers.TimerListener; import commonj.timers.TimerManager; public class TimerServlet extends HttpServlet { private static final long serialVersionUID = 1L; protected static void logMessage(String message, PrintWriter out){ out.write("<p>"+ message +"</p>"); System.out.println(message); } @Override public void service(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException { PrintWriter out = response.getWriter(); // out.println("<html>"); out.println("<head><title>TimerServlet</title></head>"); // try { // logMessage("service() entering try block to intialize the timer from JNDI", out); // InitialContext ic = new InitialContext(); TimerManager jobScheduler = (TimerManager)ic.lookup("weblogic.JobScheduler"); // logMessage("jobScheduler reference " + jobScheduler, out); // jobScheduler.schedule(new ExampleTimerListener(), 0, 30*1000); // logMessage("Timer scheduled!", out); // //execute this job every 30 seconds logMessage("service() started the timer", out); // logMessage("Started the timer - status:", out); // } catch (NamingException ne) { String msg = ne.getMessage(); logMessage("Timer schedule failed!", out); logMessage(msg, out); } catch (Throwable t) { logMessage("service() error initializing timer manager with JNDI name weblogic.JobScheduler " + t,out); } // out.println("</body></html>"); out.close(); } private static class ExampleTimerListener implements Serializable, TimerListener { private static final long serialVersionUID = 8313912206357147939L; public void timerExpired(Timer timer) { SimpleDateFormat sdf = new SimpleDateFormat(); System.out.println( "timerExpired() called at " + sdf.format( new Date() ) ); } } } Then I executed the servlet to start the scheduling on the first managed instance (Noddy server), which returned as expected: (Servlet execution output) service() entering try block to intialize the timer from JNDI jobScheduler reference weblogic.scheduler.TimerServiceImpl@43b4c7 Timer scheduled! service() started the timer Started the timer - status: Which resulted in the creation of 2 rows in my DB tables: WEBLOGIC_TIMERS table state after servlet execution: "EDIT"; "TIMER_ID"; "LISTENER"; "START_TIME"; "INTERVAL"; "TIMER_MANAGER_NAME"; "DOMAIN_NAME"; "CLUSTER_NAME"; ""; "Noddy_1268653040156"; "[datatype]"; "1268653040156"; "30000"; "weblogic.JobScheduler"; "myCluster"; "Cluster" ACTIVE table state after servlet execution: "EDIT"; "SERVER"; "INSTANCE"; "DOMAINNAME"; "CLUSTERNAME"; "TIMEOUT"; ""; "service.SINGLETON_MASTER"; "6382071947583985002/Noddy"; "QRENcluster"; "Cluster"; "10.03.15" Although, the job is not executed as scheduled. It should print a message on the server's log output (Noddy.out file) with a timestamp, saying that the timer had expired. It doesn't. My log files state as follows: Admin server log (myCluster.log file): ####<15/Mar/2010 10H45m GMT> <Warning> <Cluster> <test-ad> <Noddy> <[STANDBY] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1268649925727> <BEA-000192> <No currently living server was found that could host TimerMaster. The server will retry in a few seconds.> Noddy server log (Noddy.out file): service() entering try block to intialize the timer from JNDI jobScheduler reference weblogic.scheduler.TimerServiceImpl@43b4c7 Timer scheduled! service() started the timer Started the timer - status: <15/Mar/2010 10H45m GMT> <Warning> <Cluster> <BEA-000192> <No currently living server was found that could host TimerMaster. The server will retry in a few seconds.> (Noddy.log file): ####<15/Mar/2010 11H24m GMT> <Info> <Common> <test-ad> <Noddy> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1268652270128> <BEA-000628> <Created "1" resources for pool "TxDataSourceOracle", out of which "1" are available and "0" are unavailable.> ####<15/Mar/2010 11H37m GMT> <Info> <Cluster> <test-ad> <Noddy> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<anonymous>> <> <> <1268653040226> <BEA-000182> <Job Scheduler created a job with ID Noddy_1268653040156 for TimerListener with description timedexecution.TimerServlet$ExampleTimerListener@2ce79a> ####<15/Mar/2010 11H39m GMT> <Info> <JDBC> <test-ad> <Noddy> <[ACTIVE] ExecuteThread: '3' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1268653166307> <BEA-001128> <Connection for pool "TxDataSourceOracle" closed.> Can anyone help me out discovering what's wrong with my configuration? Thanks in advance for your help!

  Read the article

< Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >