Search Results

Search found 803 results on 33 pages for 'acer aspire'.

Page 26/33 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • Wired connection not working

    - by YokoBlac
    I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

    Read the article

  • no boot option after install ubuntu 12.04 LTS using cd

    - by utamaku
    im facing a problem. after installing Ubuntu 12.04 LTS using boot from CD, when reboot there is no boot option to choose the OS. i directly log in to my Windows 7. before this im having an issue with the 'nomodeset' if not mistaken. after tick [x] on the nomodeset, i can install my Ubuntu, and stuck again at choosing the partition. so i had done 2 partitions for ubuntu, 1 partition for ubuntu ( ext3, mount /) and the other 1 for swap. then i can proceed until finished the installation. and after the system want to reboot. it take some times and just stuck at the screen doing nothing. not rebooting at all. i force to shutdown then restart again then directly go into windows 7 without boot option. in win7 the partitions for ubuntu is gone. i had tried the boot-repair thing and still doesn't help. it just show up the _ (terminal thing i guess). i typed boot repair and still the same. im using acer aspire 4736z. please anybody help me with this issue.

    Read the article

  • Problem installing Ubuntu 14.04 into a laptop using Windows 8.1

    - by AlexanderFreud
    I have used Ubuntu on my LG laptop for several years. I lately bought an Acer Aspire V5 laptop which included Windows 8.1. I don't have any data on it; I would like to just remove it completely (that horrible Windows 8.1) and install Ubuntu. I tried using a USB device with Ubuntu 14.04 (64bit version) saved on it. I changed the BIOS configuration, putting USB device first on boot order, Windows Boot Manager last. When I try to run with USB device it doesn't work. Messages like these show up: System doesn't have any USB boot option. Please select other boot option in Boot Manager Menu. Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: 1. insert your windows installation disc and restart your computer 2. choose your language settings, and then click "next" 3. click "repair your computer" If you do not have this disk, contact your system administrator manufacturer for assistance File \ubuntu\winboot\wubildr.mbr Status: 0xc000007b Info: the application or operating system couldn't be load...[?] required file is missing or contains errors. Could someone please write step-by-step procedures to install Ubuntu 14.04 after removing Windows 8.1 ? I already have done a second partition on the hard disk just in case.

    Read the article

  • Ubuntu is unresponsive and scrolling is very jerky

    - by peterpipe
    I'm new to Ubuntu. I've been using 12.04LTS for over a week now. For 3 days it was great but now I'm having a number of problems. I'm using an Acer Aspire one D255 it has a 250GB HDD and a 1GB Memory. My browser is Firefox. Pages freeze occasionally and I wait for over 10 minutes and have to use the computer's 'off' button. Pages crash. On facebook some pictures don't load and I have to close down and restart a couple of times. Scrolling can sometimes be very jerky. Downloading software has become a problem and I have a 'no entry' sign in the top taskbar. I've looked at this page for some help but the words used and the explanations are not helpful to someone like me who has little knowledge of this. Please - 'Ubuntu for dummies'. I'd like to continue using Ubuntu but am close to giving up.

    Read the article

  • In facebook pictures bdon't always load properly and scrolling is very jerky

    - by peterpipe
    I'm new to Ubuntu. I've been using 12.04LTS for over a week now. For 3 days it was great but now I'm having a number of problems. I'm using an Acer Aspire one D255 it has a 250GB HDD and a 1GB Memory. My browser is Firefox. Pages freeze occasionally and I wait for over 10 minutes and have to use the computer's 'off' button. Pages crash. On facebook some pictures don't load and I have to close down and restart a couple of times. Scrolling can sometimes be very jerky. Downloading software has become a problem and I have a 'no entry' sign in the top taskbar. I've looked at this page for some help but the words used and the explanations are not helpful to someone like me who has little knowledge of this. Please - 'Ubuntu for dummies'. I'd like to continue using Ubuntu but am close to giving up.

    Read the article

  • How do I install a driver for an Atheros AR9285?

    - by Fernando
    How to install the driver for Atheros AR9285 in Ubuntu 11.10. Still no package for 11.10 according to this https://help.ubuntu.com/community/WifiDocs/Device/Atheros/AR9285 Here is the output of the commands marc@fer-VPCYA1V9E:~$ sudo lshw -class network *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 4c:0f:6e:d6:65:cc width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.0.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:d3400000-d340ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: 54:42:49:a2:1f:bc capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:d2400000-d243ffff ioport:1000(size=128) And the second command marc@fer-VPCYA1V9E:~$ rfkill list 0: sony-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: sony-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no 4: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Is there a way to make it work?

    Read the article

  • Wireless doesn't work on a Lenovo V570

    - by Stephen
    I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

    Read the article

  • XP Mode (Windows Virtual PC for Windows 7) no longer requires hardware virtualisation - hurrah !

    - by Liam Westley
    Windows Virtual PC (aka XP Mode) When XP Mode was released, it insisted on hardware virtualisation being present on your CPU and enabled in the BIOS.  Given that Windows Virtual PC was based on an improved Virtual PC 2007, which provided hardware virtualisation as a user selectable option, I did wonder why on earth Microsoft thought this was a good idea.  Not only do many people not have a CPU with hardware virtualisation support, some manufacturers don't provide a BIOS option to enable this setting, especially on laptops - yes Sony, Toshiba and Acer, I'm looking at you. Dumb and dumber This issue became a double whammy; not only was Microsoft a bit dumb on not supporting Windows Virtual PC without hardware virtualisation, your hardware manufacturer was also dumb in not supporting the option in the BIOS. Microsoft update to Windows Virtual PC Belatedly, Microsoft has seen the problem with this hardware virtualisation requirement and has now released a new version of Windows Virtual PC that works without hardware virtualisation.  This is really good news for those with older (or limited) CPUs and rubbish BIOS firmware. You can details of how to download the new versions of XP Mode here, http://blogs.msdn.com/virtual_pc_guy/archive/2010/03/18/windows-virtual-pc-no-hardware-virtualization-update-now-available-for-download.aspx And there is also an explanation of why the hardware virtualisation requirement was in place for previous releases, http://blogs.msdn.com/virtual_pc_guy/archive/2010/03/18/windows-virtual-pc-now-without-the-need-for-hardware-virtualization.aspx

    Read the article

  • Can a usb cable carry 12v?

    - by zm15
    Here's what i'm wanting to do. I have a Acer Iconia A500 tablet. I want to plug it in, in the car, but it has a barrel plug and I don't want to buy an inverter. The car adapters are expensive for what they do. I already have a 2.1 amp usb car charger meant for the iPad: http://www.amazon.com/Kensington-K33497US-PowerBolt-Charger-Compatible/dp/tech-data/B003PU01M4/ref=de_a_smtd And i want to use this usb cable from the 2.1 amp port to plug into the A500: http://www.amazon.com/gp/product/B00304DZ7I/ref=ox_sc_act_title_2?ie=UTF8&m=A1HPBDJJIXKXS7 Here are the specs on the original wall charger if that helps: http://www.phihong.com/assets/pdf/PSA18R.pdf The usb cable says it's 5v, but the original charger says it outputs 12v. But since it's just a cable... wasn't sure if that really made a whole lot of difference since it's only 1.5 amps from the wall charger. Is it possible to use that usb cable through the powerbolt car charger, to charge the A500?

    Read the article

  • How to tell X.org to reload input device module?

    - by Vi
    When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

    Read the article

  • How to disable Microsoft eHome MCIR Keyboard and company?

    - by AndrejaKo
    Hi! I'm and unlucky owner of and Acer 7720G laptop which, like many in its category, has receiver for a proprietary infra red remote control device (which I did not receive with my laptop!) . Now my problem is that the receiver is detected as Microsoft eHome MCIR Keyboard, Microsoft eHome MCIR 109 Keyboard and Microsoft eHome Remote Control Keyboard keys. My problem is that this driver has incompatibilities with some programs I use like for example DosBox. When these devices are installed, they cause DosBox to incorrectly detect some keyboard buttons. The workaround is to remove or disable the 3 hardware devices. Unfortunately, I the disable option is grayed out and when I delete them, they are reinstalled on next restart. Is there any way to hack windows in order to prevent their installation? I was thinking about locating the drivers these devices use, but they are buried somewhere in windows installation and I don't have enough experience to find them, so I'm asking you for help.

    Read the article

  • Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

    - by Brij
    I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

    Read the article

  • Black screen after grub kernal selection menu

    - by skip
    I have an Acer eMachines e727 with Intel GMA 4500M integrated graphics (drivers updated to latest). I installed Ubuntu 12.04 using Wubi. All is well until I select the kernal (first one on the list). My display goes black. I searched for solutions and found one on Unbuntu forum which partially helped. Following that sticky post, I pressed "e" at the kernal listings. I changed the $Linux... default line to "quiet splash nomodeset" and was able to get to the login screen and desktop. I edited grub to make the nomodeset permanent (also removed the vt command as recommended). I followed through with changing grub to match the graphics as recommended in the article using the grub cli (using info from vbeinfo). I updated grub with the recommended settings but still get the black screen after selecting the kernal. Only nomodeset works to get me to the login and desktop. Once I get to the desktop, my display resolution shows being set to 1024x768 but it actually looks like 800x680. What do I need to do to get past these issues? Thanks!

    Read the article

  • Can the NVIDIA ION chipset handle streaming and gaming reasonable well?

    - by true_gritt
    I'm considering getting a small-footprint "nettop" computer to use as a home theater PC with my Samsung LN40A550 HDTV. I've been looking at systems like the AS Rock ION HT330, the Acer AspireRevo 3610, or the Asus EeeBox PC EB1501. These are all systems with NVIDIA ION chipset (Intel Atom N330 dual core CPU + NVIDIA GeForce 9400 GPU). Is the NVIDIA ION chipset powerful enough to support media streaming at HD resolutions (e.g. via Boxee, Hulu, Netflix) and casual gaming (e.g. World of Warcraft, Madden NFL) reasonably well without herky-jerky video output?

    Read the article

  • Burned white shadow on 24inch monitor

    - by elias94xx
    So I got this brand new monitor today an noticed the following problem: This happens while I'm moving my browser window for example. It's not font related, it also happens with icons as you can see on the picture. It's only persistend while I'm moving something, the faster I move it, the farther away is the shadow from the origin. I tested it on windows, linux and two different systems with DVI and VGA. Is this a known issue ? Specifications: Name: Acer S242HLCBID 1920x1080 @ 60hz 2ms response time contrast: 100.000.000:1 manufacture date: week 48 2011 LED backlights

    Read the article

  • virtual machines: optimal host os to run Windows XP guest os?

    - by user61132
    My department doesn't have the budget to upgrade my ailing Dell D620 laptop. However, I do have the option to buy my own personal computer, then use my company-issued ISO image to run Windows XP as my guest os using virtualbox or vmware. Therefore, last month, I bought an Acer AX3910-U3012 desktop that had Windows 7 as the host os (and 8G RAM). In short, I was disappointed with the performance while trying to run WinXP as the guest os. (It didn't perform much better than my laptop.) Just wondering what the optimal host os would be for running Windows XP as the guest os? (No, I can't use my company-issued ISO image to build the os for my personal computer.) FWIW, I'm willing to spend up to $2k if it's REALLY worth it, but would prefer to spend no more than $1k. Also, in an effort to cut costs, I'd prefer buy a desktop instead of a laptop. Thanks for any/all feedback.

    Read the article

  • Does OneNote have palm rejection or a hand rest spot?

    - by Richard DesLonde
    I just bought an Acer Iconia W500. I really wanted to use it for taking notes and having all the amenities of a full blown computer without the size. Using OneNote to take notes, I notice I can't rest my hand on the screen. I have read some about this and it seems the very best solution is to get a tablet with active digitizer technology, but there aren't too many with this and it is expensive. So barring that, is there any way I can rest my hand on the tablet screen while taking notes in OneNote? Or am I relegated to hovering my hand over the screen while I write notes? Does OneNote have a palm rest area or some sort of palm rejection?

    Read the article

  • laptop overheating ran defraggler and now its not as hot

    - by Marko
    Trying to diagnose and fix an overheating Acer 5735 laptop, running speedfan and doing general workload to try and cause the overheat conditions. I notice that windows xp is badly fragmented according to defraggler, at 58% fragmentation. So I defrag whilst watching the speedfan window, which was at the start reporting high warning style symbols for all of the sensors. After the defrag, I rebooted and ran a few programs, and even defraggler again and the sensors in speedfan all reported green i.e. not high. Wondering if there is a correlation between windows fragmentation causing the hard drive to work harder and produce more heat inside the laptop? dont want to just assume that the problems are resolved, so either speedfan is not accurate enough or fragmentation can lead to additional hard drive heat? All comments or suggestions welcome.

    Read the article

  • Xubuntu 12.04 : Random boot to black screen

    - by Thibaud Ruelle
    My xubuntu 12.04 has worked flawlessly since install in September. However, lately I randomly have the following boot issue : The computer boots to grub, and after choosing xubuntu either boots normally or boots to a black screen. Here are some observations I have made : The black screen seems to happen randomly. The black screen does not seem to happen in safe mode (- nomodeset in grub). The black screen does not allow me to ctrl + alt + F1-6 into a terminal. The black screen allows me to use SysRq keys (Alt + SysRq + K does not work though). The black screen often happens on first boot in several hours and the computer usually boots normally after a RSEINUB. When the computer boots I get "SP5100 TCO timer: mmio address 0xfec000f0 already in use" at startup and "Could not write bytes: broken pipe" at shutdown. However research on these errors did not yield answers to my particular issue. Comparing Xorg.0.log (successful boot) and Xorg.0.log.old (black screen), and reading the answers to similar problem, it seems that I might have a X driver issue. However the system worked flawlessly since lately. Additional info on my system : ACER AO722 C62kk Operating system : 3.2.0-31-generic ubuntu Edit : I made a fresh install of Xubuntu 12.04 x64, the issue is still there ... (I have a separate /home so config. files were not erased). Edit 2 : I followed troubleshooting blank screen, so my new observations are without quiet and splash in grub : When the system boots normally, the screen goes black after grub then lights up and displays text information then goes to login screen. (After that the desktop starting time vary substantially, which is new and may be a separate issue ?). When the boot fails, after grub the screen goes black, lights up, goes black, lights up again and most times goes black again. At this point it responds to Alt+SysReq K by lighting up but no more, and has to be rebooted through Alt+SysReq+ RSEINUB. Thank you for your time and attention in advance ! Thibaud Ruelle

    Read the article

  • How to run installation CD for second monitor?

    - by dobsoft
    I am running ubuntu 14 off of a live USB. I have a second monitor that I would like to use while using ubuntu. It has an installation cd that you have to install before using, and when I click on the .exe file the Archive Manager tries to open it and says an error occurred while loading the archive. Thanks for the help. Edit: additional information It just doesn't show up when when I'm in the display settings area. I press the locate(name is probably something else) monitor button too. I know it needs the CD because when I was using it with Windows it didn't work until I went through the installation process on the CD. If ubuntu doesn't use .exe files is there a way to use the CD still? Monitor info from label: -acer LCD monitor -model number: S200HQL Version: S200HQL bd I connect it to my computer using a VGA cord which is connected to a j5create VGA to USB adapter. Not sure if this helps: VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) lsusb output: Bus 002 Device 004: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 002 Device 005: ID 0bc2:2100 Seagate RSS LLC Bus 002 Device 007: ID 0711:5200 Magic Control Technology Corp. Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 1bcf:2c18 Sunplus Innovation Technology Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Read the article

  • Strange behavior in networking between 64bit and 32bit

    - by Rob
    I'm having a strange behavior about my network setup. I have 2 laptops, one (Lenovo) with Windows 7 Professional 64-bit and another (Acer) with Windows 7 Ultimate 32-bit and a wireless router. I'm connecting these 2 using the router but with a strange behavior. I can ping both machines, as well as the router, but when i try to access their shared folders (\\computer_name\shared_folder) the connection starts to fail and I need to reboot both machines to get it working again. But this only happens sometimes, sometimes it works.

    Read the article

  • SD-CARD reader does not show in ubuntu

    - by shantanu
    I bought Acer asipre 4250. It have built-in SD card reader. But it is not working. Nothing show in /media or fdisk but something in dmesg. dmesg: new high-speed USB device number 3 using ehci_hcd [ 127.396733] scsi5 : usb-storage 2-2:1.0 [ 128.526562] scsi 5:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 128.532512] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 129.008110] ohci_hcd 0000:00:12.0: PCI INT A disabled [ 129.032083] ohci_hcd 0000:00:13.0: PCI INT A disabled [ 129.056411] ohci_hcd 0000:00:16.0: PCI INT A disabled [ 129.338026] sd 5:0:0:0: [sdb] Attached SCSI removable disk [ 129.808328] ohci_hcd 0000:00:14.5: PCI INT C disabled [ 167.728616] usb 2-2: USB disconnect, device number 3 [ 169.872284] ehci_hcd 0000:00:13.2: PCI INT B disabled [ 169.872340] ehci_hcd 0000:00:13.2: PME# enabled fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0006bc6d Device Boot Start End Blocks Id System /dev/sda1 * 2048 48828415 24413184 7 HPFS/NTFS/exFAT /dev/sda2 48828416 50829311 1000448 82 Linux swap / Solaris /dev/sda3 50829312 99657727 24414208 83 Linux /dev/sda4 99659774 625141759 262740993 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 99659776 275439615 87889920 7 HPFS/NTFS/exFAT /dev/sda6 275441664 451221503 87889920 7 HPFS/NTFS/exFAT /dev/sda7 451223552 625141759 86959104 7 HPFS/NTFS/exFAT I found another problem just right now. I format last three drives as EXT4 with disk utility. But they are showing as NTFS/exFAT in fdisk. :-(

    Read the article

  • how can I fix error: hd0 out of disk?

    - by rux
    I am running Ubuntu 12.04 on a netbook - Acer AS 1410. After a download session, I restarted the computer and it said: error: hd0 out of disk. Press any key to continue... I pressed everything, but it's just frozen there. Any idea what's wrong with it and what I can do to fix it? I haven't been able to run my computer at all since it's frozen like that. Help please! I booted the live cd and ran sudo fdisk -lu into terminal, and here's what it gave me: Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a696263 Device Boot Start End Blocks Id System /dev/sda3 2048 117229567 58613760 5 Extended /dev/sda5 * 71647232 109039615 18696192 83 Linux /dev/sda6 109041664 117229567 4093952 82 Linux swap / Solaris /dev/sda7 4096 71645183 35820544 83 Linux Partition table entries are not in disk order I am somewhat of a beginner in this, so don't know what this means. any ideas? Thanks!

    Read the article

  • Black stripe appears to the right of the screen, impossible to get rid of

    - by Gabriele Cirulli
    After clicking the "Auto Config" button on my Acer AL2216w screen a stripe appeared on the right of the screen where the screen doesn't "exist" and I can't seem to take the screen viewport back even by using the OCD setting and moving it to the right. The left part of the screen is also hidden and I'm not able to see what's going on there. The PC is connected to the screen through a DVI adapter and a VGA cable. I also use multiple monitors and this is the second monitor. Anyway this seems not to be a related issue, as this used to happen even when I only had a single monitor. I managed to fix this issue once but it was more than two years ago and I can't remember what I did, and out of all of the things I've tried so far (connecting the screen to another PC and performing auto adjustment, switching the cables, etc.) none worked. Here's how it looks: Can anyone help me fix this?

    Read the article

  • How to force laptop mode on/off

    - by Vi
    root@vi-notebook:/home/vi# laptop_mode start force Laptop mode enabled, not active How to start laptop mode? It starts successfully when AC adapter is removed, but not by explicit command. The system is GNU/Linux Debian i386 squeeze (not up to date), 2.6.30-zen2-31270-gc7099db-dirty, Acer Extensa 5220. Update: Changed to ENABLE_LAPTOP_MODE_ON_AC=1 in /etc/laptop_mode/laptop-mode.conf, now it is turned on always. But I can't turn it off with laptop_mode stop force, it stays turned on anyway. How do I turn it off again?

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >