Search Results

Search found 803 results on 33 pages for 'acer aspire'.

Page 27/33 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Radeon HD 5770 - DisplayPort Problem

  - by Nick Schmit

  I am trying to set up 3 monitors with the Radeon HD 5770 I recieved a few days ago. I have read that I can use 2 DVI ports and an active DisplayPort adapter for a third DVI monitor. I have purchased this adapter: http://www.accellcables.com/products/DisplayPort/DP/dp_dvid.htm I have the two normal DVI monitors working, but when I try to extend the display to the third, I get a message saying the system has detected a problem with the connection through the display port which may limit resolution/refresh rate. I know that all the cables are fine, I have replaced the adapter, the monitors all work, I have tried different monitors through the adapter, and even nothing but the adapter, but I cannot get any monitor to work using it. I am trying to use 2 Dell monitors and an Acer. Have I overlooked something? Is there a compatibiliy issue I missed? Any suggestions as to what I could try? Thanks in advance.

  Read the article

• Old notebook internal display randomly not recognized

  - by jfcfar

  I have an old Acer TM4001 notebook. If the laptop is powered-off, with the lid closed, when I power it on, it generally works. Then, without touching anything, if I reboot the computer the internal display wil not work anymore. To make it working again I need to shut down the pc, close and reopen the lid and then turn it on. If I close and reopen the lid if it is not working after power the pc on, it won't work. When the screen is working, closing and opening it has no effect (the data cable seems ok). The external monitor always works as expected: If the internal display is not detected, the external will be the main (and only) display. This is not OS-related. When the screen is not working I cannot see the POST. What could be the cause for this?

  Read the article

• How do I fix a garbled screen on a Gateway LT3103u?

  - by paracaudex

  I've been having garbled screen problems on a Gateway LT3103u on Ubuntu for a while. I just did a fresh install of Ubuntu 11.10 and continue to have issues. I installed xubuntu-desktop in case the issues had to do with the sophisticated GNOME graphics. The problem is less bad, but it's still there. After a few minutes of using XFCE, the screen gets garbled. I assume this has something to do with the graphics card, but I don't know how to go about troubleshooting something like this. Where should I start? Update: Here is the description of the VGA card from lspci -vvv: 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] (prog-if 00 [VGA controller]) Subsystem: Acer Incorporated [ALI] Device 028c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- [disabled] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: radeon Kernel modules: radeon Update: Setting GRUB_CMDLINE_LINUX="nomodeset" in /etc/default/grub seems to have fixed it in both Ubuntu and xubuntu-desktop. I will test it for a day or so to see if the problems recur and then post more detail with some links to an explanation. Update 2: It is possible to use this fix for Nvidia card (GTX 260) when graphics is defective after 11.10 upgrade/install? First few restarts was graphic ok, then after few restarts begins suddenly be defective and it stay so. I must returned to 11.04 because this problem and I wait for 12.04. So I hope in this fix.

  Read the article

• I want to upgrade my GPU to MSI NVIDIA N630GT-MD4GD3 4 GB DDR3 Graphic card

  - by jatin singh

  Hello every body this is my first post here.. I want to know about my motherboard's PCI express version , my motherboard as I don't have 10 reputation so I am providing image link here http://i.stack.imgur.com/6PWV9.png I have PCI express slot and I want to upgrade it to MSI NVIDIA N630GT-MD4GD3 4 GB DDR3 Graphic card.. this GPU has PCI exp version 2. Here in my city,the shopkeeper said that we have to check if the PCI express of my board is compatible to that GPU but I want to purchase it from flipkart because they sell it for less money (sorry for bad English :/) I mailed to my computers company (Acer) but they didn't reply to any of my mail so my friend told me about Super User.

  Read the article

• Install full version of Unity on Chrome OS using crouton

  - by Sam Kong

  I have an Acer Chromebook. Using crouton, I installed Ubuntu (unity) on it. I am pretty familiar Ubuntu 12.04. But the installed one is very minimized package. My fonts are missing and I manually installed language pack for Korean but still browser can't display Korean characters. Is there a way to install the whole packages via crouton like when you install Ubuntu 12.04 with the CD? Or is there a script that installs the missing packages on the bare Ubuntu? Thanks. Sam

  Read the article

• Can't install or update Ubuntu after using parameter acpi_osi = Linux

  - by Lucas Leitão

  I recently had an issue with my acer 4736z notebook because I was having a blank screen after booting the OS, then someone told me to use the parameter GRUB_CMDLINE_LINUX_DEFAULT = "quiet splash acpi_osi = Linux" after quiet splash inside the grub. It worked for me, but since then I can't install a thing or update anything on Linux because it says Removing linux-image-extra-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-extra-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-extra-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Removendo linux-image-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Erros foram encontrados durante o processamento de: linux-image-extra-3.5.0-17-generic linux-image-3.5.0-17-generic E: Sub-process /usr/bin/dpkg returned an error code (1) I already tried to remove older kernels but it gives me the same message. Do you have a clue about what should I do?

  Read the article

• How do I re-enable the backlight?

  - by Scott Severance

  Since Oneiric, if I leave my machine (HP Mini 110 netbook) unattended and it goes into power-save mode, the backlight gets disabled. How can I turn it back on? Note that the keyboard backlight controls (Fn+F4 and Fn+F3) don't have any effect in this situation. I've already filed a bug, but filing a bug doesn't fix my problem. I tried this workaround posted in this bug report dealing with Acer laptops: sudo setpci -s 00:02.0 F4.B=0 However, if anything, that command makes things worse. In the general case, I can see a little bit if I'm in a dark room with a flashlight aimed just so. But after running setpci I can't see anything. And I find the setpci documentation to be utterly incomprehensible, so I don't know whether I need to tweak my command somehow or whether I'm completely barking up the wrong tree. Update: I've found a workaround: I'm now booting with the kernel parameter acpi=off. This disables power management, which prevents the machine from going into power saving mode and thus failing to come back up correctly. Of course, not having power management means that I can't use suspend or do anything to manage power other than powering it off (even then, I have to manually use the power switch). Also, it prevents me from using Unity 3D or Gnome Shell, forcing me into Unity 2C or Gnome Classic. So, I'd really like to be able to stop using this hack.

  Read the article

• Boot problems w/ External HDD

  - by JeremyT

  I'm having a problem with booting a live image off of a USB Hard Drive. I used Startup Disk Creator to make an Ubuntu 11.10 live image on a partition on my external so that I can use it on various computers. I set it up with ~4GB of persistent data So far I've tried it on two computers. One, a Dell, will boot to my external but it loads the select boot device very slowly. It hangs on a screen with an underscore for up to 5 minutes until it allows me to select which drive I want to boot from. After that, it works great. However, on my primary computer it doesn't work at all. It's an Acer from 2009 and it won't even recognize the drive. I don't see it anywhere in BIOS or the select boot disk list. The light on the external will come on at boot just fine so I know it's powering it at this time. Both computers worked perfectly with my 4GB flash drive that I had partitioned half and half (1st half FAT32 and second Ubuntu 11.10 live)

  Read the article

• Struggles to connect to network when using WPA with a BCM43225

  - by pst007x

  When booting my laptop, it will try to connect to my wireless network, however a window keeps popping up asking me for my security password, which has already been saved. I have to keep deleting my network settings, and reconnecting, otherwise it keeps failing to connect. My wireless is set up with a WPA, I do not want to lower my security because of this, but it is a pain and can take me 15mins plus to finally connect. The problem has only become apparent since a fresh install of 11.10. IPV6 disabled. System info: 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) Subsystem: Acer Incorporated [ALI] Device 036d Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at b3400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 02:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) Subsystem: Broadcom Corporation Device 04da Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at b2400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: wl, brcmsmac ADDITIONAL: In terminal I get this: pst007x@pst007x-ubuntu64:~$ nm-applet start ** Message: applet now removed from the notification area ** (nm-applet:2816): DEBUG: old state indicates that this was not a disconnect 0 ** Message: using fallback from indicator to GtkStatusIcon ** Message: applet now embedded in the notification area ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. ** (nm-applet:2816): DEBUG: foo_client_state_changed_cb Note this line: ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. At this point is where I am asked for the password. Please report WPA issues with Ubuntu 11.10 here: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/892727

  Read the article

• Increasing the screen resolution in Ubuntu 10.04

  - by Veera

  I'm running Ubuntu 10.04 edition on my Acer 5738Z laptop. The screen size of my laptop is about 15'' but the screen resolution in Ubuntu is stuck at 1366x768. I know that my monitor could give better resolution, because previously I was running Win XP and I was able to set higher resolution there. So, my questions here: How do I increase my screen resolution, here? As per the answer given to a related question, I tried to edit the xorg.conf file, but I couldn't find the file in the place /etc/x11/. Should I create this file? If I have to install screen drivers separately, where could I find it?

  Read the article

• Losing partitions after every reboot

  - by Winston Smith

  I have an Acer laptop with one hard disk, which up until yesterday had 4 partitions: Recovery Partition (13GB) C: (140GB) D: (130GB) OEM Partition (10GB) I read that the OEM partition has all the stuff needed to restore the laptop to the factory settings, but since I'd already created restore disks and I needed the space, I wanted to get rid of it. Yesterday, I used diskpart to do that. In diskpart, I selected the OEM partition and issued the delete partition override command which removed it. Then I extended the D: partition into the unused space using windows disk management. Everything worked fine, until I rebooted my laptop, at which point the D: drive vanished. Looking in windows disk management again, I can see that there's an OEM partition of 140GB, which is obviously my D: drive. So I used EASEUS Partition Master and assigned a drive letter to the 'OEM' partition and I was able to access my files again. However, every time I reboot, it reverts back. How do I fix this permanently?

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• Laptop Power down.

  - by BENBUN

  This question relates to my ACER laptop running Windows VISTA. Currently when I close the lid of my laptop the laptop does not power down, however when I open the lid it does. When looking at the power settings it is set to power down when closing the lid. The trigger to this seems to be the lid being opened not being closed. I seem to recall this behaviour changing when I installed Windows Media centre. Any ideas on how I can get the power down to work on the lid closing. thanks

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

• Laptop Power down.

  - by BENBUN Coder

  This question relates to my ACER laptop running Windows VISTA. Currently when I close the lid of my laptop the laptop does not power down, however when I open the lid it does. When looking at the power settings it is set to power down when closing the lid. The trigger to this seems to be the lid being opened not being closed. I seem to recall this behaviour changing when I installed Windows Media centre. Any ideas on how I can get the power down to work on the lid closing. thanks

  Read the article

• Second display freaks out when waking from sleep

  - by inkedmn

  I have two laptops, an older white MacBook and a brand new Macbook Pro. When either computer is on my desk, I connect it to a second, widescreen display (Acer, a couple years old, uses DVI). The Macbook connects via mini DVI and the MBP connects via mini displayport. When the Macbook is connected and everything goes to sleep, I'm able to wake the machine and both displays in the normal way and everything is fine. Sometimes, when waking the MBP, the laptop and primary display are fine, but the second display shows a bunch of static. If I restart the display, everything's fine. This probably happens 70% of the time when the MBP goes to sleep while connected to this display. Any idea what could be causing this?

  Read the article

• Tell me why I should bother using Linux if it's all about problems getting the OS to install or work properly? [closed]

  - by Vilhjalmur Magnussin

  Why should I spend day's trying to get Ubuntu to either install and/or work properly? I'm using an Acer Timeline X laptop and if I install 10.04 the wireless doesn't work, and if I try installing 11.04 it either won't install, or if it installs it's full of bugs causing my computer to freeze all the time. So please, I'm all open ears. Someone give me one or two good reasons to continue wasting time (in hope it eventually works) before I decide to focus my time on other things like productivity (using Windows like I've been doing successfully the last 10 years). This is the second time I give Ubuntu a try, the first time was in 2010 using Ubuntu Studio and Ubuntu Desktop, and it ended with me shifting back to Windows since I had spent more time getting everything to work than actually working while trying Ubuntu. I really don't understand why it needs to be like this. Why go on trying when all I see is forums full of discussions about problems which people are having difficulties fixing. Or maybe there is just one special type of computer which works well with Linux? Would very much like to know which computer that is. SO please, if it's not to much trouble I really want to here from someone who has something good to say about going through all this trouble just to get a working environment up and running since I already have a working environment up and running called Windows. Thanks, Villi.

  Read the article

• Davicom DM9601 USB LAN NIC Ubuntu 11.10 issue

  - by Gaurav_Java

  I have a davicom dm9601 USB ethernet card. When I plug in the device, it is detected and drivers are loaded, but I can't connect to internet using it. It works perfectly on XP, other laptop but not working on Ubuntu 11.10 How can I install the driver for this? I have tried many things But nothing is working. If I go to this link driver but not compiling or may I be doing something wrong. I found this one but don't know how to follow these steps . This is my lsusb output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 064e:a103 Suyin Corp. Acer/HP Integrated Webcam [CN0314] Bus 003 Device 002: ID 08ff:1600 AuthenTec, Inc. AES1600 Bus 005 Device 002: ID 0a46:9601 Davicom Semiconductor, Inc. DM9601 Fast Ethernet Adapter Bus 006 Device 002: ID 046d:c045 Logitech, Inc. Optical Mouse Bus 003 Device 003: ID 0a5c:2101 Broadcom Corp. Bluetooth Controller Bus 004 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc. But when I connected my Internet from different system its start working.

  Read the article

• No Wireless In Ubuntu 13.10

  - by viktorhubinette

  When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Chromebook C720 - issue suspending and booting

  - by user72727

  I recently bought an Acer C720 chromebook (Celeron, 2GB RAM, 16GB SSD) with the intention of loading Linux and using it as a cheap development laptop while on my holiday. The installation sort of went ok but initially the trackpad didn't work so I ran a script that mostly fixed that. My current issues are: Booting: it still goes to the chrome "unknown os" white screen - I have to press ctrl L - then escape then 1 then wait for 30 secs while it seems to be searching for something. Then Ubunto loads up fine. Any idea how to fix this? Suspend: if I close the lid of the laptop then it doesn't seem to suspend properly. At least when I open the lid the screen appears to be on but the screen is blank with a cursor. Nothing responds on the keyboard and I have to hold the power down to restart it. The suspend from the top menu has the same issue. Moving windows: I don't have a mouse click button so how do I move windows around the screen? Launcher bar: I've set mine to auto hide (which it does) but what exactly do you have to do to get it back? I just repeatedly jab the mouse at the side of the screen and eventually it pops up. I don't mind starting all over again but obviously a quick fix is preferred ;) Mike Ubunto 14.04.1 LTS Kernel 3.13.0-32-generic PS Sorry for so many questions.

  Read the article

• ATI Radeon 5800 series dual monitor unity not 3D accelerated

  - by Victor S

  When I had a single monitor setup, without Xinerama, with my current setup of Ubuntu 11.10, ATI 5800 series card, Unity showed transparencies, shadows, etc. (although graphics was reported as 'Standard' in the control/settings panel). Having switched to a dual monitor setup, dell 24" UltraSharp and a smaller Acer monitor, Unity shows only as 2d, even though I'm not loggin in to that display manager. WebGL performance is very sluggish, I'm getting the impression that the processor is doing all the work and the card isn't even accessible even though the drivers are installed (from the ubuntu repository, I did not compile custom drivers). Any tips on how to enable full 3D accelerationn and video card support. Here is my xorg.conf file: Section "Monitor" Identifier "0-DFP3" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1680x1050" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-DFP4" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1920x1200" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-0" Device "amdcccle-Device[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-1" Device "amdcccle-Device[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Module" Load "glx" EndSection Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[1]-0" 0 0 Screen "amdcccle-Screen[1]-1" 1920 0 EndSection Section "Device" Identifier "amdcccle-Device[1]-0" Driver "fglrx" Option "Monitor-DFP4" "0-DFP4" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "amdcccle-Device[1]-1" Driver "fglrx" Option "Monitor-DFP3" "0-DFP3" BusID "PCI:1:0:0" Screen 1 EndSection Section "ServerFlags" Option "Xinerama" "on" EndSection More info: fglrxinfo display: :0 screen: 0 OpenGL vendor string: ATI Technologies Inc. OpenGL renderer string: ATI Radeon HD 5800 Series OpenGL version string: 4.1.11005 Compatibility Profile Context

  Read the article

• No picture on HDMI Output from a Pioneer 921 AV Receiver to a Projector

  - by Alexey Kulikov

  I am trying hard to tackle a what seemed to be simple problem if wiring my setup together. The setup: Mac Mini (2011) with HDMI Output Pioneer 921 K AV Receiver Acer HD Projector (HDMI) When I hook up my Mac Mini directly to the Projector with a 30 foot (10 meter) HDMI Cable everything is just fine. The picture is sharp and the colors brilliant. However, when I send HDMI to the receiver (into the BD HDMI Input) then I get absolutely no HDMI output to the projector, it keeps saying "no signal". Is there perhaps some magic combination of setup buttons that may help me resolve this problem?

  Read the article

• Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

  - by rick2047

  I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

  Read the article

• unstable / variating sound level (volume) within same song / clip

  - by Bastien

  Hello, I have a pretty standard Acer desktop (I guess a predecessor of the X5900 model). when playing mp3 / radio / youtube clips, the sound level is changing WITHIN the clip, highly annoying. in the case of an mp3, the same mp3 will play at a constant sound level on my iPod, so clearly an issue with the computer. problem existed under vista, I upgraded to windows 7 and have the same issue. I guess it might be soundcard-related, so updated the drivers, no luck neither. any idea ? thanks

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33  | Next Page >