Search Results

Search found 5716 results on 229 pages for 'dual channel'.

Page 26/229 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Adding partitions to dual boot on Windows

  - by Bernard

  I am trying to install Ubuntu 12.04 along side Windows 7 on an HP mini 210 netbook. I have down loaded an iso image OK and got the installation program working but I am having problems with partitioning. I want to keep my Windows installation intact so I am following the 'Other' installation route. I have managed to shrink the main Windows partition down to 50GB leaving 250GB free space but I can't find a way of adding any extra partitions for Ubuntu. The free space gets listed by the installer as 'unusable' but on the graphic at the top its called 'free space'. If I select this and click 'Install Now' I get an error message: 'No root file system is defined'. I have tried clicking the Add, Change Delete and New Partition table buttons with the unusable partition selected and nothing happens. How do I define a root mount point when I do not have any Linux partitions?

  Read the article

• A glitch after Ubuntu Installation. Cannot boot Ubuntu

  - by Starx

  I am trying to create a dual boot of Ubuntu 10.10 with Windows 7. My hard disk allocation were as follows: Windows 7 NTFS 100 GB /boot EXT4 200 MB SWAP LINUX SWAP 4 GB / EXT4 46 GB After installation is complete, instead of getting the boot screen of Ubuntu, it directly boots from windows 7 without asking anything. What is wrong? I run the Live Cd again using USB drive and I see that the \boot, and \ are occupied with most likely Ubuntu data. Now How do i point my Laptop to point to Ubuntu Boot instead of Windows Boot

  Read the article

• Xubuntu dual monitor broke display

  - by Arman yaraee

  After I used Settings Display to enable my second monitor, my first display is not working anymore either. So I enabled both, then clicked save configuration since it was working and boom it crashed. Now when I start up, I can see the screen which I type my password but it goes black after that! When I boot into recovery mode it works fine but in Settings Display I don't see HDMI at all to disable it. Is there anyway to restore all display setting to default? (I can Ctrl+ALT+F1 and type commands but xrandr returns no results over there) EDIT I should clarify that system bios is set to laptop display

  Read the article

• Can you install ubuntu on xp and then uninstall xp? how?

  - by Eli

  I have a problem with my pc, you can read about it here if you like http://yhoo.it/qIQyMw anyway, I might go for ubuntu, the thing is I'm in Lebanon and here few, very few people use linux, most of them never heard about ubuntu lol, therefore you'll be really lucky if you can buy an ubuntu cd or even if you find someone can find someone capable of installing it. So when they fix my pc, they might install xp coz they don't have a linux operating system, and i hate win 7 and vista so I'll have to download ubuntu and install it by myself, I don't want to dual boot coz i don't have a super computer lol, i have used ubuntu on my vps, never on desktop before so i would like to know if you can download ubuntu, install it, on a xp pro, then remove xp pro? is there any tutorial? thank you

  Read the article

• Why does my Grub have two entries for Windows?

  - by Tomas Lycken

  I have a dual boot system with Ubuntu 12.04 and Windows 7, using GRUB2 (with Burg) as boot loader. For some reason, the Windows installation shows up twice in the boot menu: Ubuntu GNU/Linux, with Linux 3.2.0-24-generic Ubuntu GNU/Linux, with Linux 3.2.0-24-generic (recovery mode) Windows 7 (loader) (on /dev/sda1) Windows 7 (loader) (on /dev/sda2) If I look in my partition table, /dev/sda2 is C:\ of the Windows installation, and /dev/sda1 is the "System Reserved" partition (which, IIRC, is Windows' own bootloader). Furthermore, gparted shows /dev/sda2 - but no other partitions - with a boot flag: What is going on here? I'd like to have only the entries for Ubuntu and one entry for Windows in my boot menu - how do I remove one of them?

  Read the article

• Just updated, after reboot my computer won't start up again

  - by Alex

  I have a macbook that I use on occasion which dual boots Ubuntu and OSX (It has rEFIt installed). I turned it on for the first time in a while and it needed a bunch of updates. So I let it run, and restarted it when it asked. When it was booting up, it got stuck at a light blue screen. There was nothing on the screen to indicate that it was doing anything - I figured it just got stuck or something, so I turned it off and back on. (I suspect now it was actually working, but I had no indication that it hadn't just frozen) Now I can't access either OSX or my Ubuntu partition. When I choose ubuntu on the rEFIt menu, it shows "No bootable device -- insert book disk and press key". If I try to start up OSX is looks like it starts loading, but instead of an apple logo there's a crossed out circle icon.

  Read the article

• Grub Boot Error After Ubuntu Update

  - by Anna

  I've installed Ubuntu 10.04 with dual boot to Windows XP. I put it on auto-update. It was updating grub et al and after a restart all it says is; error:no such device: <hex number> With a grub rescue prompt. I'm in panic mode right now as it's my mother's office computer and it might have some serious repercussions for her tomorrow. What should I do? Update: It appears that the partition structure has been corrupted since it only displays (hd0) on ls

  Read the article

• Uninstall backtrack 5 dual booted with Ubuntu

  - by omerjerk

  Some days ago I installed BackTrack over my Ubuntu installation. I was having some problems in the bootloader of BackTrack. So I set default bootloader to that of Ubuntu. I didn't remember the command that I typed. so now the default bootloader is of Ubuntu and I want to completely remove BackTrack. how to do that ? If I just delete the installation files of backtrack from ubuntu then it'll still be there in the bootloader.

  Read the article

• Cannot install ubuntu on Asus UX51VZ

  - by Andrey Frunt

  I removed Win8, changed partition table from GPT to MBR and installed Win7. The problem is that I don't see the grub after I installed ubuntu and only win7 boots. Any ideas? I tried to reinstall all of listed above about 5 times but with no success :( I tried both 13.04 and 13.10 UPD: I also tried Boot-Repair and it installed the grub2 for me but unfortunately only with options to run ubuntu, so I repaired bootrecord using windows tools to have an ability to run to windows. Anyway I still cannot configure the dual boot. Please help :)

  Read the article

• Trouble with Wubi and dual boot install

  - by noam

  Is there a difference between wubi install and doing an install of Ubuntu alongside windows7? I ask because I used wubi, but I'm having trouble with certain things like being unable to change my brightness settings and I'm wondering if installing from a usb drive would change anything. Also, I've tried to do a usb drive install, but it doesn't give me the option to install alongside, it only shows the "Replace Windows 7" and "something else" options. Is this because I already did a wubi install?

  Read the article

• DSL modem problem in 11.10

  - by Misterious

  Earlier I used Windows 7 and the modem used to work absolutely fine. Even when it got disconnected it used to reconnect automatically without any trouble. But then I installed Ubuntu 11.10 on dual-boot and set up the modem connection properly but the modem now disconnects much more frequently (earlier it disconnected once in 5 hours or so and after Ubuntu in 5 minutes!). Also once disconnected, it does not reconnect even when I have checked the "Connect Automatically" button. I have to restart the system to reconnect it. I the clean installed Windows and modem works perfectly fine again. What is the reason for this and how can I solve this? I really want to use Ubuntu but due to this problem I can't.

  Read the article

• restoring grub when Windows 7 MBR lost it

  - by Trent Hall

  My dual boot desktop was running only Windows 7 until it crashed on a windows update. Couldn't get it started again even after all the usual things that might fix it, so I installed Ubuntu 12.04, which has worked very well. unfortunately Carbonite doesn't run on Linux yet, and so I called Microsoft support to see if we could be Windows 7 up and running. Their attempts to get Windows 7 running resulted in writing a new MBR for windows, which failed and also somehow caused the loss of ability to boot into Ubuntu also. How can I get back to Ubuntu? I don't want to lose my settings in Ubuntu. Thanks... Trent

  Read the article

• Purple screen on boot, iMac

  - by Eugene B

  I have just installed Ubuntu 13.10 (special iMac iso found here) on the new iMac (dual boot). Installation of rEFIt was completed successfully, as well as the installation of Ubuntu itself. After the final reboot, rEFIt sees this distributive and allows the choice. When I select "Boot linux from HD", it sends me to grub screen, where I can select Ubuntu. And then it gets stuck on the purple screen (smpboot: Booting Node 0, Processors #1 -- for the recovery mode) with no further action. Does anybody know a solution to this problem? P.S.: I have also tried both 32 and 64-bit pc distributives (occasionally) with the same result.

  Read the article

• Roll Your Own Passive 3D Movie System with Dual Projectors

  - by Jason Fitzpatrick

  If you’d like to enjoy 3D movies with passive polarized glasses for less than $50,000 (the average price of a passive 3D projector), this DIY setup brings the price down to a more accessible level. Courtesy of 3D movie and theater enthusiast Jahun, this guide details how you can achieve passive 3D projection using two radically less expensive projectors, cheap polarized filters, and some software. The project won’t be free-as-in-beer but with some careful shopping the bill will ring up at the thousands instead of tens-of-thousands of dollars. Hit up the link below to see how he pulled off miming a $50,000 projector for less than a tenth the cost. Passive Projection [via Hack A Day] How to Get Pro Features in Windows Home Versions with Third Party Tools HTG Explains: Is ReadyBoost Worth Using? HTG Explains: What The Windows Event Viewer Is and How You Can Use It

  Read the article

• A rather long question about installation/uninstall

  - by user2364312

  Ok so here's the deal guys, last week I decided I want to install Ubunutu again because I really missed it. (Last time I had an ubunutu was 7.somehting) I downloaded 12.04 and isntalled it via bootable usb device. Knowing how dual boots works I cleared up some space on my hard disc before hand using the windows 7 built in disc manager. During Ubunutu's installation I thought that by choosing "Install Ubuntu alongside Windows 7" will automatically just use the space I cleared before, but apperentaly it did not since that partition is still 100% free space. On what partition is Ubunutu installed when using that method? And how can I uninstall it to re-install it back on the space I cleared up for it? Thank you very your time reading and helping!

  Read the article

• Dual Screen with 12.04 ATI randr extension is not present

  - by Trevor Pearson

  Here's my problem I have two screens. One is a 22"led monitor and the other is 42 inch led tv. In windows 7 I run xbmc on the second monitor. I'm trying to mimic the same function in setting xbmc to display on the tv only. So I installed the latest x64 linux drivers from ATI. I configured (using the catalyst control panel) using single display (multi desktop) I then got a white screen with black x so I enable xinerama. with xinerama enable I got the displays to work correctly, however I received an error when I tried to enter display settings to change the launcher location. the error message was " "randr extension not present =" So I tried to install libxandr2 using terimal but here's what I get trev@Lrig:~$ sudo get-apt install libxander2 [sudo] password for trev: sudo: get-apt: command not found I'm at a loss now because I can't find a solution for the xandr error message. I'f my specs are important amd athx2 6400+ ghz 8 gigs ram radeon hd6950

  Read the article

• 12.04 Dual Monitor Configuration changes to "Mirrored" automatically

  - by Josef

  After installing 12.04 on my Samsung X120 Notebook (with Intel GMA 4500 internal graphics card) i have a Problem with the configuration off my 2nd monitor. Its a 22" with 1680 * 1050 Pixel connected via HDMI. I use the display configuration and set internal display=off and external display=main display. That works fine. After rebooting i still have that configuration, but after a while (often when i press a button on the keyboard), the configuration automatically changes to "Mirror Screen" and the internal display switches on. Both displays then have a bad resolution. When i do the manual display configuration again, everything is fine for the duration of that session. What could be the problem, that this display configuration gets lost / resets?

  Read the article

• dual boot missing files on ntfs

  - by yehuda

  I have 3 partitions: one for win7 (ntfs), one for Ubuntu (ext4) and one just for data (ntfs so both operating systems can see them). My problem is that I had stored some files on the data partition using ubuntu and when i booted win7 all that data was gone! After that I couldn't find the files even when using Ubuntu. My files were simply GONE :( Is there something I can do in Ubuntu or is it just windows problem?

  Read the article

• Permanently mounting Windows' NTFS partition, fully enabled

  - by Bart van Heukelom

  I'm transforming a Windows 7 PC into a dual boot system with Ubuntu 10.10. Following other questions on this site, I've mounted my Windows drive by adding this to fstab UUID=blabla /windows ntfs users,defaults,umask=000 0 0 It appears to work well, I can read and write, but it appears to be a bit crippled still. When I tried to update an SVN working copy with RabbitVCS, it complained that it couldn't write to a temporary file inside the working copy, even though the permissions are all on 0777 inside /windows (by default, I haven't done that manually). It even corrupted that working copy :( It works when I use the command line SVN client with sudo, but that's hardly user friendly.

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• Windows 7 can't boot with Ubuntu on different hard drive

  - by dellphi

  I use a dual boot with two hard disks and two OS is Ubuntu 10.04 and Windows 7. Windows 7 installed on the first disk, first partition. Grub is installed on a second hard disk MBR, and Ubuntu installed on an extended partition on a second hard drive. When I select Windows 7 on the Grub menu, the HDD lamp lights up briefly and then black screen on the monitor, with the status of the keyboard is still functioning. Until now (with the default boot from first HDD), I have to press F12 to get into the Grub to run Linux on a second HDD. output of fdisk -l grub.cfg. I want to retain Grub to remain on the second HDD, and Windows 7 could choose from the menu provided by Grub. But I do not get how, I hope anyone can help.

  Read the article

• Boot Ubuntu from a bootable USB hangs on purple screen

  - by user210946

  I recently bought a laptop (Lenovo Y410P) with Windows 8 pre-installed and I'm trying to dual boot Windows 8 and Ubuntu 13.0. I created a bootable usb using Pendrive. Then I changed the Boot Mode to Legacy Support and the boot order so it boots from the flash storage first. When I restarted the computer, I got the error message "SYSLINUX 4.06 EDD 2012-10-23 Copyright (c) 1994-2012 H. Peter Anvin et al" and it just hung there. Fair enough. After some googling I formatted my flash drive in FAT format instead of FAT32. The "SYSLINUX..." error message is gone but now it hangs on a purple screen http://imgur.com/WbdXpZN Does anyone have a suggestion what to do here? I've looked at various posts but none of them seems to have a solution that the author confirmed it worked.

  Read the article

• Dual Boot Windows 8 with Ubuntu 12.10

  - by karthik nayak

  This is my First time so please help/ Steps I Followed : Install windows 8 pro with media centre On my asus k55vm, i7 ,8gb. windows boots fine and is in perfect condition. booted into Ubuntu live USB and installed ( it detected windows, installed alongside windows 8 with recommended setting ) installed perfectly. rebooted , but no option to select Ubuntu, just loads into windows 8 without any option, tried boot repair and no use . Please HElp , tried many tutorials to no use , heard about easybcd also , any help ?

  Read the article

• 12.04, nvidia-settings makes one of my dual monitors grey and useless, disables network

  - by Kerrick

  I'm running Ubuntu 12.04 64-bit, Precise Pangolin, with a PNY GTS 250 1GB video card and a monitor plugged into each of the DVI ports. I'm using the proprietary drivers (post-release updates). If I set anything to do with Separate X Screens up in nvidia-settings (and write it to xorg.conf and reboot), my second monitor has a grey background, no menu bar, no ability to have a window on it, the second monitor doesn't get picked up in a screneshot, and if I move my mouse cursor to it it's an ugly black X. Plus, my network is unable to connect to anything. If I subsequently delete /etc/X11/xorg.conf and reboot, everything goes back to working, albeit with a single monitor activated. If I set anything to do with TwinView up in nvidia-settings, my second monitor starts working, but it isn't seen as a second monitor by Ubuntu, so I can't apply color calibration to it separately. Plus, my mouse gets "caught" between the monitors every time I try to move my cursor between the two. What gives? If it helps, this is the xorg.conf that nvidia-settings generates for Separate X Screens.

  Read the article

• Ubuntu install and dual Boot with Windows 8 UEFI

  - by Jose Maria

  i have Ubuntu 12.04 x64 ISO, i load it on a Fat32 USB. My notebook has a hdd with GPT where i installed Official Win 8 Pro x64 (final versión), I partitioned the whole hdd, previously of win 8 install, and bios is set with UEFI boot. My BIOS notebook doesn't support SECURE UEFI BOOT. So I boot the notebook from USB and the Grub runs OK showing whether to run Ubuntu live or to install, but neither one neither two works, when I choose then the screen shows black and nothing happen, it doesn't start/loads the install program. I've try whether to prepare the usb with unetbootin, or just direct copy/paste the files onto the USB. I also have try WUBI, but neither with success, it launch an error when ending.

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >