Search Results

Search found 1139 results on 46 pages for 'isp'.

Page 26/46 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • unusual webpage access problem

    - by user28163
    This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

    Read the article

  • Avoiding double NAT with PPPoA connection

    - by user498429
    I've got an ASUS RT-N56U wending its way to me and have been thinking about how to set this up on my home network. I currently have a Netgear DG634g V5 and was hoping to use this device as a modem only, with everything else being done by the router. Problem is, my ISP uses PPPoA and the asus seems only to support PPPoE. I'm aware that a double NAT configuration should be avoided and I've seen some instructions here: http://www.tomshardware.co.uk/forum/33700-17-ultimate-modem-router-setup-thread Specifically, I was going to follow the guidance in the section entitled "Chaining Two Networks Together In a Cascading Fashion (Modem handles PPPoA)". That seems like it could work. However, is this a double NAT configuration or even a good way to do it? Would UPnP still work? The other option, I understand, is to buy the Draytek Vigor 120 but I'd ideally like to avoid the cost of that if its not necessary.

    Read the article

  • Route an IP from WAN to a host on LAN on OpenWRT

    - by Zsub
    EDIT: I know how to use NAT, I specifically want the server to be reachable on two IP's, one private, one public, with the firewall of the OpenWRT in between, if feasible. At the office we have recieved a /29 from our ISP. The first address is reserved for their endpoint, so I'm free to use five addresses. We run a local network, so of course there is a router in between running OpenWRT to provide all hosts with (W)LAN (dhcp from a private range). However, we also have a server running OS X Server 10.6 (Snow Leopard) and I'd like that server to be accessible both from the LAN using a private IP as well as from the WAN on it's own public IP. Point of note is that the server only has one network port, so multiple NICs is not an option, unfortunately. How would I go about doing this?

    Read the article

  • "DNS not responding" error with D-Link router and PPTP internet connection

    - by Born2win
    I have a D-Link DIR-615 router since around six months. My internet connection is VPN (PPTP) based, i.e. I have been given a username and password from my ISP and my IP address is dynamic. Since a few days I am experiencing a serious problem. My router connects normally (I can see the yellow light), but my computer is giving me a "DNS not responding" error. I have tried everything (reset, reboot etc.) but no success.

    Read the article

  • I just got a linode VPS a week ago and I've been flagged for SSH scanning...

    - by meder
    I got a 32-bit Debian VPS from http://linode.com and I really haven't done any sort of advanced configuration for securing it ( port 22; password enabled ). It seems somehow there is ssh scanning going on from my IP, I'm being flagged as this is against the TOS. I've been SSHing only from my home Comcast ISP which I run Linux on. Is this a common thing when getting a new vps? Are there any standard security configuration tips? I'm quite confused as to how my machine has been accused of this ssh scanning.

    Read the article

  • Please recommend tools for PC, browser, home network performance problems?

    - by mobibob
    My client is experiencing some odd response behavior in their browser for the past few days. Classic, "nothing has changed" so I am starting at ground zero. Browsing a website will timeout or take a ridiculous time to load -- other times, the same site and query is immediately responsive. Once a connection is established, video streams are uninterrupted. The home network hosts a website, but it is not experiencing any activity in Apache's 'access.log' I am using speedtest.net to check if the ISP through the internet is 'OK' -- which looks typical (average +/-). I have to suspect the home network is beaconing or something very abnormal, but I don't know where to start.

    Read the article

  • stunnel: SSL-to-SSL? (for smtp/imap)

    - by nonot1
    Hello, How can I configure stunnel to accpet SSL connections, and connect then to an SSL port on a different server? Here is my setup: Our ISP's server, "Mail Server", supports smtp/imap over SSL. (Not starttls. Just over ssl.) But, I have a bunch of client machines that will only trust a specific, internal, root certificate. Thus, they can not connect to "Mail Server". For these client machines, I'd like to make a dedicated "Mail Tunnel" host that uses stunnel to listen with an in-house signed SSL certificate, and just forward data to "Mail Server" using a 2nd SSL connection. Can this be done? What would be the specific steps for Ubuntu Server 10.10? (I'm not too familiar with persistent service configuration.) Thank you

    Read the article

  • Iptables mark incoming packet - vpn routing

    - by Tom
    I have connected my home to my workplace for out of house backup reasons through openvpn. The connection is working nicely. At work I have 5 fixed IP addresses. Now I would like to assign one of these IP addresses to be forwarded to my home machine. I have confirmed packet arrival at my home machine with tcpdump. The problem is that my default route at home is NOT the tun0 (naturally), but eth0 to my own ISP. So I created a separate routing table to route my tun0 packets back to where they belong, but do not how to mark the incoming packet which arrive through tun0 with iptables, so I can drive them back. I do not want any port restrictions, but only what comes from tun0 should leave through tun0 thanks tom

    Read the article

  • IPv6 6to4 on Windows Server

    - by Graham Wager
    I'm looking for a relatively simple guide to setting up an IPv6 tunnel properly. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

    Read the article

  • Public IP shows strange characters and Facebook registers logged-in session to a different location

    - by Stuart Kershaw
    I'm encountering some IP strangeness today and hoping to find an explanation. In short, I'm based in Seattle, WA with my ISP being Comcast. While browsing Facebook's account settings, I noticed that my active session was located to Mount Laurel, NJ. At that point I ran a search in Google for 'my public IP', which returned an interesting result: a string of characters in the following format: 2601:8:b000:xxx:xxxx:xxxx:xxxx:xxxx Normally, a search for my IP returns something like: 67.xxx.xx.xxx A phone call to Comcast got me nowhere, but using Comcast's phone-menu debugging tools, I was able to send a 'refresh signal' to my modem. After that, the search for 'my public IP' yielded the expected result... for about 5 minutes, and then it returned to the new string of characters. Does anyone know of an explanation for this?

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • Configuring subdomains for a machine (Win2k8) in a lan

    - by RMS
    I am currently setting up a windows 2008 server to host a website with multiple subdomains, all accessible only within the lan. also, there is no active directory. what I did is : 1 - computer name : 'web' 2 - in IIS, I added a site binding as 'site1.web' to the default web site 3 - added DNS role to the server 4 - added 'web' as principal zone in direct lookup zones (default options) 5 - added CNAME 'site1' From a client machine, in tcpip config I added the ip address of 'web' to the DNS list in addition to the ISP DNS. (client machine ip is from DHCP) Now browsing to 'http://web' or 'http://site1.web' works correctly. My question is, is it possible throught additional steps in the server to have the websites accessible without requiring the DNS config in all the client machines ? thanks in advance

    Read the article

  • Accessing Windows from Linux/Mac by name using TCP/IP

    - by stevekuo
    What are some solutions to access Windows by its computer name from Linux and Mac using TCP/IP. That is, from terminal I want to be able to ping my Windows PCs using its host name. My setup is: Various machines running Ubuntu, Windows XP and OS X. Networked using a consumer grade wireless router which provides DHCP. The only DNS is the ISP's, which resolves Internet names and not local host names. The Windows machines can ping each other by name. The Ubuntu and OS X machines can only ping Windows by IP address (name doesn't work).

    Read the article

  • Postfix configuration: different outgoing hosts based on sender

    - by Joe
    I've seen a few answers to this on the web, but nothing definitive nor any good examples. I relay all my mail out through Postfix, currently everything sent to my ISP's mail server. However, there are a few users with gmail accounts or gmail-hosted accounts; I'd like to route their outgoing mail through Google's servers (since it will then appear in their Gmail sent folder). All email NOT from one of these senders should go out through the default relayhost. I believe I need to use the "sender_dependent_default_transport_maps" configuration within Postfix, but can't find a good example on what this setup looks like. Can anyone point me at a specific setup?

    Read the article

  • CentOS 5.5 x86_64 VPS - A lot of inbound traffic when idle?

    - by Matt Clarke
    I have a CentOS VPS from UKWSD and I'm getting inbound traffic that I cannot understand. The VPS was setup yesterday and I installed vnstat this morning around 10am, since then the server was basically idle and doing nothing from 12pm but it's showing activity inbound which is way over what it should be and i'd say the outbound is pretty much over to top too. Here is vnstat (snapshot taken at 10:30pm GMT) http://i.imgur.com/XnORb.jpg Here is the iptables http://pastebin.com/uGxX2Ucw The reason I'm concerned is.. 1) I have no idea why this is happening, and I like to know what's going on :D 2) I've calculated (briefly) that this pointless traffic would use around 15-20GB of bandwidth per month, and when your on a 150GB limit - it's quite an issue. I'm struggling to understand this and I thought I'd get some advice before asking my ISP (and risk looking completely stupid) Regards Matt

    Read the article

  • Apache availability with the two front-ends on diferent locations. Is it possible?

    - by marc.riera
    Hello, I have to locations (office and service providers). One DNS(bind) serving our domain as authoritative, and a service provider webserver with our corporate web on a private server. So.. Now we are planing to upgrade our server on the ISP to a new one, and I would like to use this situation to improve our service. Is it possible to mount a high availability apache/mysql/php within to different locations? I will install a bind slave on the same new server, so I hope it will make things easier, but I need some hints and tips on how to ride it. THanks.

    Read the article

  • Linux QoS: bulk data transmission during idle times

    - by syneticon-dj
    How would I do a QoS setup where a certain low-priority data stream would get up to X Mbps of bandwidth, but only if the current total bandwidth (of all streams/classes) on this interface does not exceed X? At the same time, other data streams / classes must not be limited to X. The use case is an ISP billing the traffic by calculating the bandwidth average over 5 minute intervals and billing the maximum. I would like to keep the maximum usage to a minimum (i.e. quench the bulk transfer during interface busy times) but get the data through during idle/low traffic times. Looking at the frequently used classful schedulers CBQ, HTB and HSFC I cannot see a straightforward way to accomplish this.

    Read the article

  • What are some good, IP Address Management solutions for IPv6? [closed]

    - by Russell Heilling
    There are a number of open source IPAM tools available for IPv4 address management; however there seems to be a distinct lack of actively updated tools available for IPv6. Other than FreeIPdb (code no longer maintained) or the RIPE Database (I have seen some customisations to the RIPEdb that allow for enterprise/ISP IPAM but it seems like overkill for a system that will probably only ever handle one /32 worth of space). Are there any other options that I'm missing? (Database only please. I know vi can be used for flat text IPAM, that's how I'm handling our /32 at the moment, but I don't see it scaling for much longer) It doesn't have to be open source but what are folks doing to manage IPv6 in a dual stack environment

    Read the article

  • Odd internet packet routing

    - by NachoChip
    I want to know is there anyway to explicitly control the packet routing. I try to connect my computer in HK from San Francisco. It is extremely slow and I use tracert to see what is going on. It seems the packet get routed from HK to Europe and then to New York and then to San Francisco. In US, I am using Astound Cable. Is there any suggestion I can force the packet to not go around the world before it reach my computer? Or it is all ISP dependent?

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • BGP Router reccomendations for simple redundancy [closed]

    - by Jona
    We have two sites that each have an internet connection and have a dedicated dark fibre between them. Each site has it's own IP space and we have an AS number. We're looking to be resilient to failure of the internet connection to either site and so need to buy a pair of approriate routers. Requirements are: Able to run 2 bgp sessions (one with the ISP, one with the other site router) Option to take a full table from the upstream ISPs would be nice. Able to provide HA gateways on the LAN side (e.g. 192.168.0.254 will automatically migrate if it's host router lost power) A dedicated device rather than a server running Linux / BSD Not crazy expensive. Any help / advice much appreciated.

    Read the article

  • Why don't DNS root servers answer?

    - by JustTrying
    If I try to query a root server with dig, I never receive an answer. For example the output for dig @b.root-servers.net www.ubuntu.com is ; << DiG 9.8.1-P1 << @b.root-servers.net www.ubuntu.com ; (1 server found) ;; global options: +cmd ;; connection timed out; no servers could be reached But if I query other servers (the one of my ISP, or 8.8.8.8), they answer correctly. Why?

    Read the article

  • Technicolor TG582n with external DHCP server [on hold]

    - by Jack
    We have a small home setup with a Technicolor TG582n on Plusnet ISP. We have a Samba4 DC with DNS forwarding enabled. The DC forwards to the Technicolor. However, the client machines have their DNS settings manually set. This is an annoyance when using laptops on other networks. We would like to have DHCP handled on the server machine, such that when a client connects to the Technicolor, it gets its IP and DNS information from the DHCP server, eliminating the need to manually set adapter DNS settings. However, I cannot find an option to disable DHCP on the Technicolor and am not completely clear on how one would point DHCP services to the server from the Technicolor if there were the option. So, how would one make the Technicolor use an external server for DHCP leases?

    Read the article

  • SPF record doesn't work (not sure which DNS server to tweak)

    - by Ion
    Problem: Google (and perhaps others) marks our emails as SPF neutral. Let me give you some background about the setup: initially got a dedicated server (Hetzner) with Plesk installed to host a domain/web application, let's say: bigjaws.com. Plesk automatically creates a DNS zone for it with some records for the various services it provides out of the box, e.g. webmail.bigjaws.com as a CNAME to bigjaws.com to provide Horde/whatever, etc. Let me point out four relevant of these records (where XXX.XXX.XXX.158 is our dedicated IP): bigjaws.com. A XXX.XXX.XXX.158 mail.bigjaws.com. A XXX.XXX.XXX.158 bigjaws.com MX (10) mail.bigjaws.com. bigjaws.com. TXT v=spf1 +a +mx -all The above records are not(?) valid anymore though, because after using this dedicated server for a while, our site got bigger and bigger so we decided to move our operations over to AWS (EC2, RDS, ELB, etc), but we retained the mail functionality as is, i.e. emails from [email protected] are sent by connecting to our dedicated server where Plesk takes care of things. This was decided in order not to setup anything from scratch. Of course for all DNS-related things we now use Route53. In Route53 I have the following records: mail.schoox.com. A XXX.XXX.XXX.158 bigjaws.com. MX (10) mail.bigjaws.com bigjaws.com. SPF "v=spf1 +ip4:XXX.XXX.XXX.158 +mx ~all" From my understanding of SPF, the SPF status should have been passed: I designate that all email being sent by bigjaws.com from XXX.XXX.XXX.158 are valid/not spam (I added +mx there but I'm not sure if needed). When a mail server receives an email, doesn't it lookup the SPF record of the domain and checks against the IP it got the email from? Checking with spfquery: root@box:~# spfquery -ip XXX.XXX.XXX.158 -sender [email protected] -rcpt-to [email protected] StartError Context: Failed to query MAIL-FROM ErrorCode: (2) Could not find a valid SPF record Error: No DNS data for 'bigjaws.com'. EndError noneneutral Please see http://www.openspf.org/Why?id=employee1%40bigjaws.com&ip=XXX.XXX.XXX.158&receiver=spfquery : Reason: default spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com Received-SPF: neutral (spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com) client-ip=XXX.XXX.XXX.158; [email protected]; If I go to the address listed above (openspf.org) it tells me that the message should have been accepted(!): spfquery rejected a message that claimed an envelope sender address of [email protected]. spfquery received a message from static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) that claimed an envelope sender address of [email protected]. The domain bigjaws.com has authorized static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) to send mail on its behalf, so the message should have been accepted. It is impossible for us to say why it was rejected. What should I do? If the problem persists, contact the bigjaws.com postmaster. Also, here are some headers from an email sent by one of our [email protected] addresses to a gmail.com address (by the way, bigjaws.de listed in the "Received: from" field was the initial domain hosted on the dedicated server before adding the .com one -- both are still listed as separate subscriptions under Plesk). Delivered-To: [email protected] Received: by 10.14.177.70 with SMTP id c46csp289656eem; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) X-Received: by 10.14.102.66 with SMTP id c42mr306186eeg.47.1382515860386; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) Return-Path: <[email protected]> Received: from bigjaws.de (static.158.XXX.XXX.XXX.clients.your-server.de. [XXX.XXX.XXX.158]) by mx.google.com with ESMTPS id l4si19438578eew.161.2013.10.23.01.10.59 for <[email protected]> (version=TLSv1 cipher=RC4-SHA bits=128/128); Wed, 23 Oct 2013 01:10:59 -0700 (PDT) Received-SPF: neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=XXX.XXX.XXX.158; Authentication-Results: mx.google.com; spf=neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=default; d=bigjaws.com; b=WwRAS0WKjp9lO17iMluYPXOHzqRcOueiQT4rPdvy3WFf0QzoXiy6rLfxU/Ra53jL1vlPbwlLNa5gjoJBi7ZwKfUcvs3s02hJI7b3ozl0fEgJtTPKoCfnwl4bLPbtXNFu; h=Received:Received:Message-ID:Date:From:User-Agent:MIME-Version:To:Subject:Content-Type:Content-Transfer-Encoding; Received: (qmail 22722 invoked from network); 23 Oct 2013 10:10:59 +0200 Received: from hostname.static.ISP.com (HELO ?192.168.1.60?) (YYY.YYY.ISP.IP) by static.158.XXX.XXX.XXX.clients.your-server.de. with ESMTPSA (DHE-RSA-AES256-SHA encrypted, authenticated); 23 Oct 2013 10:10:59 +0200 Message-ID: <[email protected]> Date: Wed, 23 Oct 2013 11:11:00 +0300 From: BigJaws Employee <[email protected]> User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64; rv:24.0) Gecko/20100101 Thunderbird/24.0.1 MIME-Version: 1.0 To: [email protected] Subject: test SPF Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit test SPF Any ideas why SPF is not working correctly? Also, are there any DNS settings that are not needed anymore and create a problem?

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >