Search Results

Search found 1106 results on 45 pages for 'lo wai lun'.

Page 26/45 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33 | Next Page >

Can't connect to website after altering IPTables

- by user2833135

I attempted to open up a port on my VPS, but I can't connect to my website after opening up that port. Below are the commands I issued to open the port. I didn't get an error or anything after setting this up. I just can't connect to my website after doing this. [root@vps ~]# iptables -F [root@vps ~]# iptables -A INPUT -i lo -j ACCEPT [root@vps ~]# iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT [root@vps ~]# iptables -A INPUT -p tcp --dport 25765 -j ACCEPT [root@vps ~]# iptables -P INPUT DROP [root@vps ~]# iptables -P FORWARD DROP [root@vps ~]# iptables -P OUTPUT ACCEPT [root@vps ~]# iptables -L -v Just a side note, but I am running CentOS 6 (64 bit) Thank you in advance.

Read the article
Reset DRAC/MC password on Dell BladeCentre 1855

- by Farseeker

I have a Dell Blade Centre 1855, and nobody knows what the root password for the DRAC/MC card in the blade chassis is (I tried root/calvin). I do not have IP access to the DRAC/MC, nor do I have physical access to the back of the blade centre to access the DRAC/MC module. I do have serial access (and can see the login prompt in hyperterm). I do have physical access to the FRONT of the chassis (the back of the cabinet is locked and lo-and-behold the key cannot be found). Does anyone know how to reset the password? Every piece of literature I find on the internet tells me I need to log in, or run racadm on the host machine (which I can't, because it's inside a blade chassis). If someone does know how to do it with physical access to the back of the bladecentre, please post it anyway, as I'm sure I'll get access to the back of the cabinet one day)

Read the article
How to know my wireless card has injection enabled?

- by shrimpy

I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

Read the article
CentOS - massive usage on loopback interface

- by Matthew Iselin

Hi, I have a CentOS installation which is running fairly smoothly. Today I ran ifconfig mainly to see what sort of usage has been coming across the ethernet interface, and to also check my link speed. This is what I ended up seeing for the loopback device: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10301085132061223274 errors:0 dropped:0 overruns:0 frame:0 TX packets:13981054163812689233 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11783901785008000095 (0.6 EiB) TX bytes:10333501021200548281 (0.9 EiB) This just feels completely wrong - almost an EiB of data? Any assistance in tracking down the source of these statistics would be greatly appreciated.

Read the article
iptables to allow 80 and 443 on chillispot running ddwrt

- by user76682

I am having problems setting this up. this is what I am trying to do. I have Chillispot (hotpsot) running on dd-wrt. Everything is setup, but the client wants only 80 and 443 to go through through the hotspot. I found this tutorial for dd-wrt but that doesnt seem to work. http://www.dd-wrt.com/wiki/index.php/Iptables#Allow_HTTP_traffic_only_to_specific_domain.28s.29 Initially I tried to place the options at the top but didnt work. then i flushed the iptables and set only these three. I can see the pkts number grow but for some reason I can browse. root@DD-WRT:~# iptables -nvL FORWARD Chain FORWARD (policy ACCEPT 3105 packets, 2442K bytes) pkts bytes target prot opt in out source destination 1629 230K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 multiport dports 21,80,443 2346 2792K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 328 46420 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 Heres some info from the router, chillispot is the tun0 interface. root@DD-WRT:~# iptables -vnL FORWARD --line-numbers Chain FORWARD (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 ACCEPT 47 -- * vlan1 192.168.8.0/24 0.0.0.0/0 2 0 0 ACCEPT tcp -- * vlan1 192.168.8.0/24 0.0.0.0/0 tcp dpt:1723 3 32 1851 ACCEPT 0 -- tun0 * 0.0.0.0/0 0.0.0.0/0 state NEW 4 0 0 ACCEPT 0 -- br0 br0 0.0.0.0/0 0.0.0.0/0 5 48 2408 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 6 756 452K lan2wan 0 -- * * 0.0.0.0/0 0.0.0.0/0 7 756 452K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 8 0 0 TRIGGER 0 -- vlan1 br0 0.0.0.0/0 0.0.0.0/0 TRIGGER type:in match:0 relate:0 9 0 0 trigger_out 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 10 0 0 ACCEPT 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 state NEW 11 0 0 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 12 0 0 DROP 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 13 0 0 DROP 0 -- * br0 0.0.0.0/0 0.0.0.0/0 The interfaces: root@DD-WRT:~# ifconfig -a br0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:192.168.8.1 Bcast:192.168.8.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1862 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:259721 (253.6 KiB) TX bytes:254862 (248.8 KiB) br0:0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:2508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1066410 (1.0 MiB) TX bytes:376001 (367.1 KiB) Interrupt:5 eth1 Link encap:Ethernet HWaddr 00:12:17:CF:80:61 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:729 errors:0 dropped:0 overruns:0 frame:114693 TX packets:697 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107869 (105.3 KiB) TX bytes:473134 (462.0 KiB) Interrupt:4 Base address:0x1000 etherip0 Link encap:Ethernet HWaddr 1E:13:B7:09:CC:8C BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1210 (1.1 KiB) TX bytes:1210 (1.1 KiB) teql0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.182.1 P-t-P:192.168.182.1 Mask:255.255.255.0 UP POINTOPOINT RUNNING MTU:1500 Metric:1 RX packets:662 errors:0 dropped:0 overruns:0 frame:0 TX packets:587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:92167 (90.0 KiB) TX bytes:427657 (417.6 KiB) vlan0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1864 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:269558 (263.2 KiB) TX bytes:262680 (256.5 KiB) vlan1 Link encap:Ethernet HWaddr 00:12:17:CF:80:60 inet addr:10.3.2.47 Bcast:10.255.255.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2675 errors:0 dropped:0 overruns:0 frame:0 TX packets:645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:705429 (688.8 KiB) TX bytes:102197 (99.8 KiB) The routing table: root@DD-WRT:~# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.182.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0 10.3.2.0 0.0.0.0 255.255.255.0 U 0 0 0 vlan1 192.168.8.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.3.2.1 0.0.0.0 UG 0 0 0 vlan1 Highly appreciate your help. TIA, Arun

Read the article
Como instalar Windows (x86/x64) sobre Linux (Ubuntu)

- by yorrany

I installed Ubuntu edition (10.04) on my windows 7, completely eliminating it to the original installation. After I was forced to reverse the process, but could not find tools or explanations of how to do it. To clarify the equipment, it is: a netbook, acer, no optical drive cd / dvd, the process should be fully via USB. I hope I was clear enough, count on the support of you. Thank you. -- Instalei a edição Ubuntu (10.04) sobre meu Windows 7, eliminando completamente a a instalação original. Depois fui forçado à reverter o processo, mas não encontrei ferramentas ou explicações de como fazê-lo. Para esclarecer sobre o equipamento, trata-se de: um netbook, acer, sem leitor óptico de cd/dvd, o processo deverá ser totalmente via USB. Espero ter sido bastante claro, conto com o suporte de vocês. Muito obrigado.

Read the article
OpenVZ multiple networks on CTs

- by picca

I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

Read the article
udev: waiting for uevents to be processed on my Gentoo

- by stan31337

During the startup I see machine executing this thing for about 30 seconds: udev: waiting for uevents to be processed Then I get a quick message which says something like: devfs: timeout (50 seconds) I can't see the whole thing because after that system starts up very fast including Xfce. What logs and configs do I need to provide for further investigation? $uname -a Linux genta 3.6.6-gentoo #1 SMP Sun Nov 11 11:02:23 NOVT 2012 i686 Genuine Intel(R) CPU T2300 @ 1.66GHz GenuineIntel GNU/Linux Thank you! UPD: rc-status genta / # rc-status sysinit Runlevel: sysinit dmesg [ started ] udev [ started ] devfs [ started ] genta / # rc-status boot Runlevel: boot hwclock [ started ] modules [ started ] fsck [ started ] root [ started ] mtab [ started ] localmount [ started ] sysctl [ started ] bootmisc [ started ] hostname [ started ] termencoding [ started ] keymaps [ started ] net.lo [ started ] swap [ started ] urandom [ started ] procfs [ started ]

Read the article
openwrt uses a single interface bridge?

- by timbo

My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

Read the article
Error when make "make install" PHP WebDav

- by kron

Hi, I'm having issues install PHP WebDAV onto Fedora8 - after downloading and running make install I get the following errors: [root@ip-18-192-114-35 dav]# make install /bin/sh /tmp/dav/libtool --mode=compile gcc -I. -I/tmp/dav -DPHP_ATOM_INC -I/tmp/dav/include -I/tmp/dav/main -I/tmp/dav -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -c /tmp/dav/dav.c -o dav.lo gcc -I. -I/tmp/dav -DPHP_ATOM_INC -I/tmp/dav/include -I/tmp/dav/main -I/tmp/dav -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -c /tmp/dav/dav.c -fPIC -DPIC -o .libs/dav.o /tmp/dav/dav.c:21:23: error: ne_socket.h: No such file or directory /tmp/dav/dav.c:22:24: error: ne_session.h: No such file or directory /tmp/dav/dav.c:23:22: error: ne_utils.h: No such file or directory /tmp/dav/dav.c:24:21: error: ne_auth.h: No such file or directory /tmp/dav/dav.c:25:22: error: ne_basic.h: No such file or directory /tmp/dav/dav.c:26:20: error: ne_207.h: No such file or directory /tmp/dav/dav.c:35: error: expected specifier-qualifier-list before 'ne_session' /tmp/dav/dav.c: In function 'dav_destructor_dav_session': /tmp/dav/dav.c:152: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:153: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:155: error: 'DavSession' has no member named 'base_uri_path' /tmp/dav/dav.c:156: error: 'DavSession' has no member named 'user_name' /tmp/dav/dav.c:157: error: 'DavSession' has no member named 'user_password' /tmp/dav/dav.c:158: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c: In function 'cb_dav_auth': /tmp/dav/dav.c:194: error: 'DavSession' has no member named 'user_name' /tmp/dav/dav.c:194: error: 'NE_ABUFSIZ' undeclared (first use in this function) /tmp/dav/dav.c:194: error: (Each undeclared identifier is reported only once /tmp/dav/dav.c:194: error: for each function it appears in.) /tmp/dav/dav.c:195: error: 'DavSession' has no member named 'user_password' /tmp/dav/dav.c: In function 'zif_webdav_connect': /tmp/dav/dav.c:212: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:212: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:213: error: 'ne_uri' undeclared (first use in this function) /tmp/dav/dav.c:213: error: expected ';' before 'uri' /tmp/dav/dav.c:215: error: 'uri' undeclared (first use in this function) /tmp/dav/dav.c:259: error: 'DavSession' has no member named 'base_uri_path' /tmp/dav/dav.c:260: error: 'DavSession' has no member named 'base_uri_path_len' /tmp/dav/dav.c:262: error: 'DavSession' has no member named 'user_name' /tmp/dav/dav.c:264: error: 'DavSession' has no member named 'user_name' /tmp/dav/dav.c:267: error: 'DavSession' has no member named 'user_password' /tmp/dav/dav.c:269: error: 'DavSession' has no member named 'user_password' /tmp/dav/dav.c:271: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c: In function 'get_full_uri': /tmp/dav/dav.c:304: error: 'DavSession' has no member named 'base_uri_path_len' /tmp/dav/dav.c:307: error: 'DavSession' has no member named 'base_uri_path_len' /tmp/dav/dav.c:313: error: 'DavSession' has no member named 'base_uri_path' /tmp/dav/dav.c:313: error: 'DavSession' has no member named 'base_uri_path_len' /tmp/dav/dav.c:314: error: 'DavSession' has no member named 'base_uri_path_len' /tmp/dav/dav.c: In function 'zif_webdav_get': /tmp/dav/dav.c:329: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:329: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:330: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:330: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:348: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:354: error: 'ne_accept_2xx' undeclared (first use in this function) /tmp/dav/dav.c:359: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:359: error: invalid type argument of '->' /tmp/dav/dav.c: In function 'zif_webdav_put': /tmp/dav/dav.c:377: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:377: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:378: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:378: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:396: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:405: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:405: error: invalid type argument of '->' /tmp/dav/dav.c: In function 'zif_webdav_delete': /tmp/dav/dav.c:422: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:422: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:423: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:423: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:441: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:448: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:448: error: invalid type argument of '->' /tmp/dav/dav.c: In function 'zif_webdav_mkcol': /tmp/dav/dav.c:465: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:465: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:466: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:466: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:484: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:491: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:491: error: invalid type argument of '->' /tmp/dav/dav.c: In function 'zif_webdav_copy': /tmp/dav/dav.c:510: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:510: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:511: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:511: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:539: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:550: error: 'NE_DEPTH_INFINITE' undeclared (first use in this function) /tmp/dav/dav.c:550: error: 'NE_DEPTH_ZERO' undeclared (first use in this function) /tmp/dav/dav.c:554: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:554: error: invalid type argument of '->' /tmp/dav/dav.c: In function 'zif_webdav_move': /tmp/dav/dav.c:573: error: 'ne_session' undeclared (first use in this function) /tmp/dav/dav.c:573: error: 'sess' undeclared (first use in this function) /tmp/dav/dav.c:574: error: 'ne_request' undeclared (first use in this function) /tmp/dav/dav.c:574: error: 'req' undeclared (first use in this function) /tmp/dav/dav.c:598: error: 'DavSession' has no member named 'sess' /tmp/dav/dav.c:611: error: 'NE_OK' undeclared (first use in this function) /tmp/dav/dav.c:611: error: invalid type argument of '->' make: *** [dav.lo] Error 1 Any help would be much appreciated. Thanks!

Read the article
Can not change to a static IP in Fedora 19

- by user196272

Im having a bit of a weird situation. Ive installed Fedora Linux 19 onto a virtual machine with no GUI. initially eth0 does not show up when I perform ifconfig. when I run dmesg | grep eth I see the adapter but it says it changed names to p2p1. Once I perform the ifconfig p2p1 up command it shows up. Now when I try to edit the /etc/sysconfig/network-scripts/ifcfg-p2p1, it does not exist. the only scripts that are there lo and enp0s3. If I try to create the ifcfg-p2p1 file with the correct settings, I can not restart the network service. I tried editing the enp0s3 file, but that did not work. Im fairly new to linux and not sure what else to put in here, so if you need any more information just let me know and Ill put it in here.

Read the article
Linux policy routing - packets not coming back

- by Bugsik

i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

Read the article
Ubuntu, No wireless networks found after correctly installed madwifi

- by Peter

Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

Read the article
video streaming infrastructure advice

- by Alchemical

We would like to set-up a live video-chat web site and are looking for basic recomendations for software and hardware set-up. Most streams will be broadcast live from a single person with a web cam, etc., and viewed by typically 1-10 people, although there could be up to 100+ viewers on the high side. Audio and video do not have to be super-high quality, but do need to be "good enough". The main point is to convey the basic info in the video (and audio). If occasionally the frame-rate drops low and then goes back to normal fairly soon, we could live with that. Budget is an issue, so we are in general looking for a lower cost solution that will give us most of what we need in temers of performance and quality. We are looking at Peer1 for co-lo. The rest of our web site will be .Net / Windows platform. We are open to looking at any platform for the best streaming solution, although our technical expertise is currently more on the Windows side.

Read the article
Xen DomU on DRBD device: barrier errors

- by Halfgaar

I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

Read the article
How to drop all subnets outside of the US using iptables

- by Jim

I want to block all subnets outside the US. I've made a script that has all of the US subnets in it. I want to disallow or DROP all but my list. Can someone give me an example of how I can start by denying everything? This is the output from -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:ftp state NEW DROP icmp -- anywhere anywhere Chain FORWARD (policy DROP) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination And these are the rules iptables --F iptables --policy INPUT DROP iptables --policy FORWARD DROP iptables --policy OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp -i eth0 --dport 21 -m state --state NEW -j ACCEPT iptables -A INPUT -p icmp -j DROP Just for clarity, with these rules, I can still connect to port 21 without my subnet list. I want to block ALL subnets and just open those inside the US.

Read the article
Can't launch Oneiric x64 instance on Eucalyptus

- by Bruno Reis

EDIT: after many hours, I've found out that the problem has nothing to do with Eucalyptus. It looks like the image is buggy. Very, very buggy. More details in the end. I didn't manage to fix it, and I will file a bug. EDIT 2: I managed to fix it, it apparently works. I have a 4-machine cluster running Ubuntu Server Natty (11.04) x64. I've installed "Ubuntu Enterprise Cloud" from the installtion CD (then updated it) on each of these machines. The cloud seems to work fine, I have lots of virtual machines running Natty servers on them. Now I'd like to run Oneiric in a virtual machine, but somehow I can't. I downloaded Oneiric's (x64) image from http://cloud-images.ubuntu.com/oneiric/current/, published it (uec-publish-tarball oneiric-server-cloudimg-amd64.tar.gz oneiric-server-cloudimg-amd64) exactly as I did with Natty, then tried to launch an instance (euca-run-instances -n 1 -k my-key -t m1.small -z my-cloud emi-XXXXXXXX) using Oneiric's image, but the instance is not able to boot. With euca-get-console-output I get the following: [ 0.461269] VFS: Cannot open root device "sda1" or unknown-block(0,0) [ 0.462388] Please append a correct "root=" boot option; here are the available partitions: [ 0.463855] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 0.465331] Pid: 1, comm: swapper Not tainted 3.0.0-13-generic #22-Ubuntu [ 0.466526] Call Trace: [ 0.466989] [<ffffffff815d3ee5>] panic+0x91/0x194 [ 0.467860] [<ffffffff81ad1031>] mount_block_root+0xdc/0x18e [ 0.468891] [<ffffffff81ad126a>] mount_root+0x54/0x59 [ 0.469829] [<ffffffff81ad13dc>] prepare_namespace+0x16d/0x1a7 [ 0.470883] [<ffffffff81ad0d76>] kernel_init+0x140/0x145 [ 0.471837] [<ffffffff815f38e4>] kernel_thread_helper+0x4/0x10 [ 0.472889] [<ffffffff81ad0c36>] ? start_kernel+0x3df/0x3df [ 0.473884] [<ffffffff815f38e0>] ? gs_change+0x13/0x13 The filesystem is labeled "cloudimg-rootfs", inside the image both /etc/fstab and /boot/grub/grub.cfg always refer to the image by the label, everything seems to be correct, yet the kernel says it can't find the root file system. I've spent many hours googling, but nothing came out. I've asked on #ubuntu-server, but nobody knew what to do. I've asked on #eucalyptus but got no answer at all. Any ideas on why this is happening and how to solve it? Thanks EDIT: after many hours, I've found out that the problem has nothing to do with Eucalyptus. It looks like the image is buggy. Very, very buggy. The first problem is that the Kernel in the image is a -generic kernel, while I suppose it should be a -virtual one. I chrooted into the image, removed the -generic packages, replaced it with the -virtual ones. Then I extracted the new kernel (and replaced the original one (-generic) that came with the tarball) because I need it when I publish and launch an image with Eucalyptus. The problem described above was solved. But then, the console started showing this: mount: mount point ext4 does not exist If you check the /etc/fstab file in the image, it says: LABEL=cloudimg-rootfs ext4 defaults 0 1 Damnt, where's my mount point? Note that it is missing /proc as well. Well, when you think it is over, you will notice that your instance will have no network connectivity. Let's check /etc/network/interface: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback Oh my! It is missing eth0... here I stopped. I can't take no more. I give up. Looks like Canonical has just forgotten to properly set up this image. At first, I though: "have I downloaded a server image by mistake?", but no, I double checked. It is really the cloud image, it has even "cloud-init" installed (which is not, by default, on server images). They just forgot to prepare it. I will file a bug (and reference it here once this is done), and hope they fix it soon! EDIT 2: it looks like the network configuration was the last thing missing. I decided to test it with the fixes above, and it booted properly! However, I haven't got the slightest idea if the image is now good to go...

Read the article
Xen 4.2 on CentOs 6.3 : can't compile a libvirt 0.9.10 xen-activated?

- by Frederic

I followed that tutorial for Xen 4.2 on CentOs 6.3. http://www.howtoforge.com/virtualization-with-xen-on-centos-6.3-x86_64-paravirtualization-and-hardware-virtualization When building a new libvirt package with rpmbuild -bb libvirt.spec I get that error : CC libvirt_driver_libxl_la-libxl_conf.lo In file included from libxl/libxl_conf.c:43: libxl/libxl_conf.h:61: error: field 'ctx' has incomplete type libxl/libxl_conf.h:80: error: field 'ctx' has incomplete type libxl/libxl_conf.h:81: error: expected specifier-qualifier-list before 'libxl_waiter' libxl/libxl_conf.c: In function 'libxlMakeDomCreateInfo': libxl/libxl_conf.c:365: warning: implicit declaration of function 'libxl_init_create_info' [-Wimplicit-function-declaration] libxl/libxl_conf.c:365: warning: nested extern declaration of 'libxl_init_create_info' [-Wnested-externs] libxl/libxl_conf.c:367: error: 'libxl_domain_create_info' has no member named 'hvm' libxl/libxl_conf.c:383: warning: implicit declaration of function 'libxl_domain_create_info_destroy' [-Wimplicit-function-declaration] libxl/libxl_conf.c:383: warning: nested extern declaration of 'libxl_domain_create_info_destroy' [-Wnested-externs] libxl/libxl_conf.c: In function 'libxlMakeDomBuildInfo': libxl/libxl_conf.c:406: warning: implicit declaration of function 'libxl_init_build_info' [-Wimplicit-function-declaration] libxl/libxl_conf.c:406: warning: nested extern declaration of 'libxl_init_build_info' [-Wnested-externs] libxl/libxl_conf.c:408: error: 'libxl_domain_build_info' has no member named 'hvm' [...] Do you know what I need to install or change to pass that step?

Read the article
Linux Bridge, Samba netbios name/hostname access

- by Christopher Wilson

I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

Read the article
NMap route determination on Windows 7 x64

- by user30772

C:\Windows\system32>nmap --iflist Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 06:51 Central Daylight Time ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MTU MAC eth0 (eth0) fe80::797f:b9b6:3ee0:27b8/64 ethernet down 1500 5C:AC:4C:E9:2D:46 eth0 (eth0) 169.254.39.184/4 ethernet down 1500 5C:AC:4C:E9:2D:46 eth1 (eth1) fe80::5c02:7e48:8fbe:c7c9/64 ethernet down 1500 00:FF:3F:7C:7C:2B eth1 (eth1) 169.254.199.201/4 ethernet down 1500 00:FF:3F:7C:7C:2B eth2 (eth2) fe80::74e4:1ab7:1b7d:a0d0/64 ethernet up 1500 14:FE:B5:BA:8A:C3 eth2 (eth2) 10.0.0.0.253/24 ethernet up 1500 14:FE:B5:BA:8A:C3 eth3 (eth3) fe80::b03e:ddf5:bb5c:5f76/64 ethernet up 1500 00:50:56:C0:00:01 eth3 (eth3) 169.254.95.118/16 ethernet up 1500 00:50:56:C0:00:01 eth4 (eth4) fe80::b175:831d:e60:27b/64 ethernet up 1500 00:50:56:C0:00:08 eth4 (eth4) 192.168.153.1/24 ethernet up 1500 00:50:56:C0:00:08 lo0 (lo0) ::1/128 loopback up -1 lo0 (lo0) 127.0.0.1/8 loopback up -1 tun0 (tun0) fe80::100:7f:fffe/64 point2point down 1280 tun1 (tun1) (null)/0 point2point down 1280 tun2 (tun2) fe80::5efe:a9fe:5f76/128 point2point down 1280 tun3 (tun3) (null)/0 point2point down 1280 tun4 (tun4) fe80::5efe:c0a8:9901/128 point2point down 1280 tun5 (tun5) fe80::5efe:ac14:fd/128 point2point down 1280 DEV WINDEVICE eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} lo0 <none> lo0 <none> tun0 <none> tun1 <none> tun2 <none> tun3 <none> tun4 <none> tun5 <none> **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 JMeterX - I worded that way in hopes of raising answer efficnecy, but that probably wasnt the smartest choice. IMHO the problem (could be a symptom) is that nmap retardedly chooses eth0 as the gateway interface for any and all networks. Here's the result: C:\Windows\system32>nmap 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:43 Central Daylight Time Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 0.95 seconds C:\Windows\system32>nmap -e eth2 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:44 Central Daylight Time Nmap scan report for esxy5.dionne.net (10.0.0.55) Host is up (0.00070s latency). Not shown: 991 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 427/tcp open svrloc 443/tcp open https 902/tcp open iss-realsecure 5988/tcp closed wbem-http 5989/tcp open wbem-https 8000/tcp open http-alt 8100/tcp open xprint-server MAC Address: 00:1F:29:59:C7:03 (Hewlett-Packard Company) Nmap done: 1 IP address (1 host up) scanned in 5.29 seconds Just to be clear, this is what makes absolutly no sense to me whatsoever. For reference, I've included similar info from an Ubuntu (that works normally) vm on the affected host below. Jacked Windows 7 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 Working Ubuntu VM root@ubuntu:~# nmap --iflist Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MAC lo (lo) 127.0.0.1/8 loopback up eth0 (eth0) 172.20.0.89/24 ethernet up 00:0C:29:0A:C9:35 eth1 (eth1) 192.168.225.128/24 ethernet up 00:0C:29:0A:C9:3F eth2 (eth2) 192.168.150.128/24 ethernet up 00:0C:29:0A:C9:49 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.225.0/0 eth1 192.168.150.0/0 eth2 172.20.0.0/0 eth0 169.254.0.0/0 eth0 0.0.0.0/0 eth0 172.20.0.1 root@ubuntu:~# nmap esxy2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT Nmap scan report for esxy2 (172.20.0.52) Host is up (0.00036s latency). rDNS record for 172.20.0.52: esxy2.dionne.net Not shown: 994 filtered ports PORT STATE SERVICE 80/tcp open http 427/tcp closed svrloc 443/tcp open https 902/tcp closed iss-realsecure 8000/tcp open http-alt 8100/tcp open unknown MAC Address: 00:04:23:B1:FA:6A (Intel) Nmap done: 1 IP address (1 host up) scanned in 4.76 seconds

Read the article
Jenkins shows same information for all projects

- by SuperCabbage

I've been using Jenkins for the last month or so and what started out as a small issue has gotten worse and worse. I have 10 projects in Jenkins, all polling from different Git repos and building to different environments but they all show the same details on the dashboard. I can still build the projects, but I have to manually enter the URL to see any console output etc. I'm running 1.536 under Ubuntu 12.04, there's not much in the logs other than the following; Oct 22, 2013 2:21:19 PM WARNING jenkins.model.lazy.AbstractLazyLoadRunMap search JENKINS-15652 Assertion error #1: failing to load /data/builds #20 EXACT: lo=23,hi=9,size=23,size2=23 – Any ideas?

Read the article
How to install Windows (x86/x64) on Linux (Ubuntu)

- by yorrany

I installed Ubuntu edition (10.04) on my windows 7, completely eliminating it to the original installation. After I was forced to reverse the process, but could not find tools or explanations of how to do it. To clarify the equipment, it is: a netbook, acer, no optical drive cd / dvd, the process should be fully via USB. I hope I was clear enough, count on the support of you. Thank you. -- Instalei a edição Ubuntu (10.04) sobre meu Windows 7, eliminando completamente a a instalação original. Depois fui forçado à reverter o processo, mas não encontrei ferramentas ou explicações de como fazê-lo. Para esclarecer sobre o equipamento, trata-se de: um netbook, acer, sem leitor óptico de cd/dvd, o processo deverá ser totalmente via USB. Espero ter sido bastante claro, conto com o suporte de vocês. Muito obrigado.

Read the article
How to install Windows (x86/x64) on Linux (Ubuntu)

- by yorrany

I installed Ubuntu edition (10.04) on my windows 7, completely eliminating it to the original installation. After I was forced to reverse the process, but could not find tools or explanations of how to do it. To clarify the equipment, it is: a netbook, acer, no optical drive cd / dvd, the process should be fully via USB. I hope I was clear enough, count on the support of you. Thank you. -- Instalei a edição Ubuntu (10.04) sobre meu Windows 7, eliminando completamente a a instalação original. Depois fui forçado à reverter o processo, mas não encontrei ferramentas ou explicações de como fazê-lo. Para esclarecer sobre o equipamento, trata-se de: um netbook, acer, sem leitor óptico de cd/dvd, o processo deverá ser totalmente via USB. Espero ter sido bastante claro, conto com o suporte de vocês. Muito obrigado.

Read the article
Apache - building extensions with apxs

- by Brian

Hello, Pardon the newbie question - I haven't worked with manually compiling Apache modules (or anything) before. I am trying to get the mod_concat module going. It seems simple enough - just requires downloading the mod_concat.c file and then running: axps -c mod_concat.c This is new to me. Does it matter which directory I put mod_concat.c before running this command? I ran it from my home directory, and I see some new files - mod_concat.la, mod_concat.lo, mod_concat.o, and mod_concat.slo - along with a new subfolder called .libs/ that contains mod_concat.so along with some other files. I'm not sure where to go from here, I have a feeling these files were created in the wrong place. Don't I need mod_concat.so to be in my apache modules directory with the rest? Thanks for the help, Brian

Read the article
Harddrive in the freezer ever work for you?

- by Stefan Thyberg

Once upon a time, my little 10 GB drive in my webserver failed and of course I had no backup, teaching me to immediately set up an automatic backup job afterwards. Anyhow, this drive refused to start and as a last-ditch effort I put it in a plastic bag and put it in the freezer overnight, since I had heard somewhere that it might work and I really didn't have any other options. The next day I take it out, immediately plug it in outside the case and lo and behold, the drive works long enough for me to copy my data off it. Have you ever had a similar experience with this method?

Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33 | Next Page >