Search Results

Search found 4141 results on 166 pages for 'router'.

Page 26/166 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Sharing files between 2 different routers

  - by Chris

  I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

  Read the article

• WPA Enterprise Wireless Bridge

  - by prestomation

  I live in college housing at a university with wifi available. unfortunately, my bedroom(where I'd like to place my PC) gets little to no reception. I'd like to place a router in the strongest spot and rebroadcast. I understand this can be done with DD-WRT/etc, but this particular network is WPA Enterprise with my own personal username/password. I can't find any concrete evidence that I can get my router to act as a repeater for this encryption. I don't currently have a router to test it on, otherwise this would be easy, I just don't want to buy a router if it will be worthless to me. Thanks for your help

  Read the article

• How can private IPV4 addresses get past iptables NAT (tcp RST,FIN)

  - by gscott

  I've got a router performing simple NAT translation using iptables iptables -t nat -o -j MASQUERADE This works fine almost all of the time except for one particular case where some TCP RST and FIN packets are leaving the router un-NAT'd. In this scenario I setup 1 or 2 client computers streaming Flash video (eg www.nasa.gov/ntv) At the router I then tear down and re-establish the public interface (which is a modem) As expected the Flash streams stall out. After the connection is re-established and I try to refresh the Flash pages, I see some TCP RST and [FIN,ACK] packets leaving the public interface (I assume as Flash attempts to recover its stream). I don't know how these packets can leave the router non-NAT'd

  Read the article

• How can I fix my WRT54GL's constant crashing?

  - by Aarthi

  I have a Linksys WRT54GL wireless router (the old blue-and-black) whose underside indicates it is Version 2. I've noticed that, on wireless mode, if I am on a Skype call or in a Google Hangout, the wireless aspect will crash completely. In addition, if I am connected via an ethernet cord, my quality (that is, how my voice is received) tanks very quickly. I suspect this is due, in part, to my internet connectivity itself (I'm on Comcast instead of Verizon FiOS, as I'd prefer) but I'd like to stop my wireless router's wireless capability from crashing. I considered a firmware upgrade, but it looks to me as if I am upgraded. Short of manually running ethernet all over my house, I'm not sure what to do. How can I solve my wireless router's issues? If the answer is "buy a new router," then that's valid, as well, in my opinion.

  Read the article

• How to troubleshoot intermittent and irregular connection errors on home network (preferrably Mac client)

  - by Martin

  Hi, I'm experiencing intermittent connection errors in our home network from two different computers, normally "Connection Reset" when browsing, but also other issues such as very slow throughput. I have approximately a network setup as below: ISP-Cable Modem-Dlink DIR 655 Router-(Ethernet)-Fon Router-Mac/Windows laptop Basically, is there a simple way to monitor the network and detect where issues are coming from? Right now we don't know if it is the Fon router, the Dlink router, the modem or the ISP. As the issue is intermittent, is there a software that regularly traceroutes a set of destinations and tests e.g. throughput, something that can help us figure out where in the chain the errors are introduced? The more automatic network monitor, the better.

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• Setting up port forwarding for web server

  - by Javier Badia

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• Doing port forwarding and then using it from within the internal network

  - by Ram Rachum

  We all know that by doing port forwarding on the router, computers from outside the network are able, on the specified ports, to access internal computers by targeting the external IP. I'm now replacing a TP-Link router with a D-link VDSL N 6740U router, (and copied over all the settings,) and I've noticed that one thing stopped working: With the TP-link router, you could access those port-forwarded computers from within the network, using the external IP, and they would be forwarded to the relevant computers. With the new D-Link router, it doesn't work. You might be wondering, why would you want to use the external IP and port forwarding when you're inside the internal network anyway and can just access the internal IP? One example for why this is useful: You have an iPhone app that connects to a service on an internal computer. The iPhone app knows to connect to the external IP. When we put that iPhone inside the internal network (via WiFi), it suddenly stops working, because it can't access the service from the external IP anymore. Is it an inherent property of D-Link routers that they do not allow accessing internal servers from inside the network by targeting the external IP? Or is there a way to make it work?

  Read the article

• Speed up file access on home network

  - by kurasa

  I have 2 PCs (Windows 7 Ultimate) and a Mac running Windows 7 using vmware fusion on my home network tied together using WRN1000 NETGEAR Router On one of the PC's I have a set of file (MYOB .myo). These use a data source to access the data in the files. Operations (reading,writing) to the .myo on the PC which hosts the files is fine but the other 2 it is painfully slow/unreliable and I am wondering what I can do to speed this up. Some ideas I have are 1. Turn off the Windows firewall on all the windows installations on the home network 2. Buy another router. Specifically a router which I can connect a USB flash drive on the back where I can put the .myo files and all the PC can access the files from the USB flash drive on the router (does this speed things up?) Any advice greatly appreciated on how I can speed up this access to data

  Read the article

• Can my ISP find out if my wireless is protected or not?

  - by Zakukashi

  Im just wondering how much my ISP knows about my activities. I have a Modem from them this modem then connects to a SITCOM wireless router which then leads to MY PC's, Phones, Laptops. I really need to know if my ISP knows if my router is in unprotected state of wireless or not. The Sitcom box it not theirs, we payed for it long after getting this internet. Does my Sitcom wireless router send data to my ISP on its own, indicating delicate information such as wireless protection on or off? Or does the ISP's modem fish out this information on its own since our wireless router is connected to it? Would greatly appreciate any answer.

  Read the article

• How to set up daisy-chained routers for separate sub-nets?

  - by joe

  This question seems to be similar to others, but I'll take a shot anyway. A client recently switched ISPs from TDS to Comcast Business Class. Before the switch, they had 5 static IP addresses assigned. Now they'll have a single IP address that will change whenever Comcast decides to do so. The issue is that this internet connection will be shared among two companies, both having (and wanting to keep) their own private subnets. Because TDS was supplying multiple IP addresses to the one location, this allowed me to put each router on the switch. Now, with Comcast, they only get one IP address, meaning there has to be a main router before the subnet routers. Luckily, the cable modem has a built-in router, which I would like to connect to each company's router, and still have DHCP enabled on all accounts. Question: What do I need to do to the subnet routers to keep them separate from each other, but still allow internet access from the main router. I would love to say "I tried this", and give you links, but everything I find on the internet only mentions daisy-chaining routers with DCHP disabled.

  Read the article

• Why are ISP's installing routers on my site when the feed is a form of ethernet already?

  - by Cosmin Prund

  I'm connected to 3 ISP's right now. Two of them already have routers at my site, the third one announced me "they need to install some equipment" when I requested BGP session. I can only assume they need to install a Router, since that connection is now working fine, using the usual /30 net block for the connection, and the "last-mile" solution is not going to change since they only installed it last week and the BGP was in the contract from the beginning. I simply don't understand this: the "feed" is already a form of ethernet. Even those they're using different technologies for the last mile, they're all entering the ISP router using an RJ45 WAN port. I assume the ISP router does something really important that can't be done by the Big Router on the other end of the connection. It must also be something that can hurt them if miss-configured, since they don't trust us (the client) to do the stuff on our router. And I'm not talking cheap throw-away routers here: One of the routers is Cisco 2800. Edit to add network details: I'm connected to 3 ISP's, two over Radio links, one over Fiber Optic. One of the radio links is going to get dropped and the other radio link will be turned into fiber sometime next year. The fiber is 20 Mbit, radio 1 is 40 Mbit and radio 2 is 2 Mbit. I've got a /24 of provider independent address space. I'm not doing out-of-the ordinary stuff with my network, I'm overly connected because my network needs to be "up" all the time.

  Read the article

• WRTP54G Bypass Login Admin

  - by vonhogen

  I've been trying to log into my WRTP54G router, but I forgot the password. Is there any way to temporarily disable the login like for the wrt54g: http://www.velocityreviews.com/forums/t519535-help-my-linksys-wrt54g-router-was-broken-into-using-the-curl-command.html If anyone has this router, could they examine the page to turn off admin login, and see what I would need to send in a POST request?

  Read the article

• Routers with USB plug to connect external storage

  - by sixtyfootersdude

  I am just about to buy a new wireless router. I want to be able to hook up a harddrive to it and let the harddrive serve the entire network. I will mostly be storing media and some backups on the drive. I know I could get some kind of NAS but I would prefer to just hook up one of my many unused hard drives directly to my router. It looks like d-link has several products that do this using shareport. If you were wanting to have network storage how would you do it? With a NAS? Using a router with a USB port. Are these systems robust? What router would you buy?

  Read the article

• iptables intercept local traffic

  - by Anonymous

  i hope someone can help me out with somewhat simple task. I'm trying to redirect a client in my router through my desktop PC, so i can dump the traffic and analyze it (its potential source of poisoning the network with malicious packets). However i don't have a second NIC on my hands and i was hoping i can redirect all the traffic from that IP through my PC. In essence to become MITM for the client. Does anyone have any idea where to start: Current state: (localip)-(router)-(internet) And what i want to do: (localip)-(pc)-(router)-(internet)

  Read the article

• How to troubleshoot Linksys E4200 Remote Management

  - by Jordan

  My Linksys E4200 is configured for Remote Management, but the router is not accepting the connections. Here's the configuration under Administration Management Remote Management Access: Remote Management: Enabled Access via: HTTP Remote Upgrade: Disabled Allowed Remote IP Address: Any IP Address Remote Management Port: 8080 The router is setup to use 192.168.10.41 as its static Internet IP address, and 192.168.35.1 as its LAN IP address. I can access the router just fine via its LAN IP address, but I can't make a connection using http://192.168.10.41:8080. I've tried variations of the settings above (enabled HTTPS, enabled Remote Upgrade, set an IP range of 192.168.10.1-254) but nothing has worked yet. Hoping someone can at least point me in the right direction. Thanks. Update: To clarify, I have a wired router that connects straight to the T1 modem. It's configured to use 192.168.10.1-254 as its internal LAN range. The E4200 wireless router in question is on that LAN using 192.168.10.41 as its WAN IP address. The E4200's internal LAN range is 192.168.35.1-254. I'm not trying to access the E4200 from the Internet, I'm just trying to access it from its WAN IP address. Thanks.

  Read the article

• Wireless N extend G range?

  - by Sam

  I've searched all over the internet for an answer to this and I can't find one. If I purchase a wireless N router, with greater range than my current G router will the range of the wireless G signal go as far as the wireless N signal? I say this because Wireless N routers are supposed to be compatible with wireless G devices. Is the wireless G a lesser signal coming out of the router? Sorry if I confused you, I am a little confused myself.

  Read the article

• howt setup remote access into computer behind 2 routers?

  - by Steve Wasiura

  I can setup remote access to a pc behind a single router/firewall by using NAT and Port Forwarding, simples! But there is a customer that shares an internet connection with another office, and they are behind a second router firewall. I drawed a picture with my crayons but I can't attach it because I'm a new account on SF. see it here: http://i.imgur.com/b3FDx.png So how would I setup remote access to the pc that is beind the second firewall? It must be something about static routes, i.e. if I hit the wan ip on port 4905 I want it to forward it to 10.0.0.30 by going through 192.168.1.10 so a route statement like for all requests to 10.0.0.30, use 192.168.1.10 ? and ass u me router 2 has a static gateway ip of 192.168.1.10 and need a standard NAT on router 2 to point port 4905 to 10.0.0.30 is this the right way, any tips? both routers are netgear consumer equipment. thanks

  Read the article

• Using a BTHomeHub as a wireless booster

  - by Ploo

  I currently have a BT HomeHub downstairs but the wireless signal isnt strong enough on the second floor. I have an old BT HomeHub from the previous contract that I wanted to set up upstairs. I currently have an ethernet cable leading up into the old router. I then took my laptop and plugged it into the old router in hopes of configuring it but when I cannot reach api.home which is the address of the router. I cannot connect to the router wirelessly either since the password was changed and I'd have to change it through config. At this point I am completely stumped, any ideas?

  Read the article

• What is the point of connecting two routers directly together

  - by rubixibuc

  The way subnets work, wouldn't connecting two router interfaces together require their own subnet between them. Unless that subnet mask has 31 bits, wouldn't that was adress space. I'm asking because I often seen that done in networking books. How can this be done without wasting IP Addresses? They usually draw this when explaining subnetting. They have a central router connected to several other each one supposed to be creating their own subnet. Is this really how subnettimg is done? Example <-------[Router 1]-----Wasteful Subnet-------[Router 2]------> | | | \/

  Read the article

• Can I regenerate the rsa key for SSH access to a Cisco router? Or should I completely erase the SSH config?

  - by Josh

  I have a production 2691 that I administer via telnet. I'd like to change that to SSH. Looking at the config, it looks like there have been keys generated in the past. I think the history here is SSH was set up, they had issues connecting, and fell back to telnet. There are a number of crypto entries, including the following: crypto pki trustpoint Gateway-2691.xxx.com enrollment selfsigned subject-name cn=IOS-Gateway-2691.xxx.com revocation-check none rsakeypair Gateway-2691.xxx.com I've also got this going... Gateway-2691#sh ip ssh SSH Disabled - version 1.99 %Please create RSA keys (of atleast 768 bits size) to enable SSH v2. Authentication timeout: 120 secs; Authentication retries: 3 Gateway-2691# My question is simply, can I run crypto key generate rsa again to set it up again? Is there a way to negate or no all of the previous ssh config so that I can start fresh there? I may be asking the wrong questions, as I'm learning here. As for the SSH how-to, I'm sure I can find information in many places. I'm just basically wondering if I need to start fresh, or if I can pick up where the last attempt at SSH config left off.

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• No external src ip in log files (my router ip appears instead)

  - by bongo_fury

  I recently retired my workhorse WRT54G router/AP in favor of a Linksys EA2700. Since then, all inbound traffic (bound to an Ubuntu 10.02 box running LAMP)logged to Syslog, Apache's error and access logs, etc. (all behind said router) is getting logged with a src ip of 192.168.1.1, that of the router's internal ip. For example, here is an old entry from apache's access.log: 74.82.68.20 - - [22/Feb/2011:10:14:34 -0600] "GET /assets/css/style.css HTTP/1.1" 304 154 "http://example.com/view.php?event_id=1" "BlackBerry8520/5.0.0.822 Profile/MIDP-2.1 Configuration/CLDC-1.1 VendorID/100" And here is one since switching the router: 192.168.1.1 - - [05/Oct/2012:21:29:25 -0500] "GET /somedir/print.css HTTP/1.1" 200 650 "http://example.com/somedir/" "Mozilla/5.0 (Windows NT 6.1; WOW64; rv:15.0) Gecko/20100101 Firefox/15.0.1"** That first field is the problem. Each and every entry in every log shows an "external" IP of 192.168.1.1, which isn't very helpful. Any ideas? Much thanks from a n00b!

  Read the article

• Cannot Resolve Host Or Access Website Through Router

  - by Boris_yo

  This is weird. I am on Windows XP with Edimax BR 6204Wg. I have 3 devices - 2 laptops and 1 smartphone. 1st laptop and smartphone are connected through WiFi to router and 2nd laptop is connected through LAN to router. Before firmware upgrade i did not try to access website but after firmware upgrade to latest version: http://www.edimax.eu/en/support_detail.php?pd_id=11&pl1_id=3#02 i had problems resolving host, pinging, tracerting and accessing website. Sometimes ping and tracert work but i cannot access website and sometimes i can access website but ping and tracert do not work. Weird? I downgraded to previous version and no changes. If i can no longer access that website through Internet Explorer, i can access it in Firefox. I tried deleting cookies, clearing cache and that seem not make difference. Switching LAN port did not make difference. When i disconnect router and connect laptop through LAN to internet modem, everything is normal. I tried resetting router, resetting to factory default settings and all did not help. At the moment i can access website on laptop connected through LAN from Firefox and Internet Explorer, but on my smartphone i can access website only with Opera but not with built-in browser and Skyfire. UPDATE: I just could only access with Internet Explorer but not with other browsers on my PC. Minutes later i could access with all browsers. But on smartphone i could only access with Opera and not with other browsers. I am confused. I also determined that sometimes i can access and sometimes can't. What is also weird is that when ping and tracert cannot resolve host, i still am able to access website.

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >