Search Results

Search found 4141 results on 166 pages for 'router'.

Page 28/166 | < Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >

• Need reasonably priced router with QoS support [closed]

  - by ULTRA_POROV

  I dont need wireless. I am expecting very heavy traffic, with possibly thousands of tcp connections open at one time. This would require that the router has good hardware. I also need to limit the different services i will provide. Lets say i need to guarantee 60% of all the bandwidth to HTTP, 10% FTP, and 10% for Mail... So the router software must have flexible QoS options as well. I don't know which one to chooose, because this information is usually not given on the router specs.

  Read the article

• Static routing on a TP-Link TL-WR1043ND

  - by igor

  My home network setup looks like this: Both routers are TP-Link TL-WR1043ND routers. The basement router handles all devices in the house that are connected via cable, handing out addresses for the 10.89.49.0/24 network via DHCP. Wireless doesn’t really work from the basement, as the signal is too weak, so I have disabled it. To do WiFi, I have added a second (identical) router downstairs. On the WAN side it is assigned the 10.89.49.101 IP address from the basement router, and on its LAN it provides the 10.89.7.0/24 network. Basic internet access works flawlessly from any device this way. I am now facing the problem that I am not able to communicate (e.g. SSH) between all devices, wired or wireless. I am able to connect from a wireless device to a wired device, for example SSH-ing from 10.89.7.X to 10.89.49.Y, but it doesn’t work the other way round—despite the fact that I have added a static route to the basement router: Does anybody have any idea on how to solve it? Both routers have already been upgraded to use the most recent firmware from TP-Link.com (Build 110429), to no avail. Errata: I would like to stick with the official firmware, switching to something like DD-WRT or OpenWrt only as a last resort.

  Read the article

• Asus WL-520GU conflicting subnet (and/or IP) with 2Wire DSL

  - by Paula

  I have an Asus wireless router: WL-520GU... and an AT&T 2Wire for my DSL connection. When I try to browse anywhere, I just get an odd message from the Asus router (in the common Asus broken-English, bad formatting, and awful spelling): http://postimage.org/image/upxrjflcj I guess it's trying to say: Your Asus Router and your 2Wire have the same subnet mask. (It doesn't say if that's good, or bad... but it sounds like they must be different.) but... But for the "solution" it looks like it's trying to say: Your Asus Router and your 2Wire have the same IP address. My Asus has the defaults: 192.168.1.1 and 255.255.255.0 My 2Wire has: 192.168.1.66 I'm not seeing where the conflict(s) could be. The Asus firmware is v3.0.0.14 . None of these problems occur with the old v3.0.0.8 firmware. Any ideas on how to fix this? (PLEASE don't say to run a totally different DD/Tomato firmware because it's "better". I need to fix THIS 1 problem, not try to convince my company to switch everything to an entirely different set of problems.)

  Read the article

• Problem with TL-R480T+ and static routes

  - by Globulopolis

  Hi! I've some question about this router. Before starting, some configurations, specified by my provider. Wan1 VPN IP - 192.168.172.84 Mask - 255.255.255.0 Gateway - 192.168.172.253 DNS - 195.110.6.7 Wan2 Dynamic IP DHCP - 168.120.1.34 Mask - 255.255.255.0 Router IP 192.168.1.1 Computer IP 192.168.1.7 Routes: route -p add 192.168.0.0 mask 255.255.0.0 192.168.172.253 route -p add 195.110.6.0 mask 255.255.254.0 192.168.172.253 route -p add 88.135.112.0 mask 255.255.240.0 192.168.172.253 route -p add 178.219.160.0 mask 255.255.240.0 192.168.172.253 For first provider I need to provide a routes. 'Cause router does not support different routes for different WAN interfaces I put them in "Static routes". But when I try to save them I've got an error: Destination IP address can not be set in a same subnet with the WAN or LAN IP address. If I change IP's to local like 192.168.x.x router tell me: Gateway must be set in a same subnet with WAN or LAN IP address. Changing mask on WAN1 interface to 255.255.0.0 doesn't help. Any ideas? PS! Or maybe I'm must email to TP-Link support?

  Read the article

• can't ssh within LAN, but can connect from outside

  - by Patrick B.

  A strange issue: I have a desktop running Ubuntu 10.04 behind a Netgear WNR1000 router performing NAT. I would like to be able to ssh into the desktop from my laptop (running Windows 7 and Cygwin). When at home, both the desktop and the laptop are connected by wireless (the desktop is in a different room from the router). sshd seems to be running fine, since ssh localhost from the desktop works without trouble. Also, ssh my.ip.address from my laptop when it is not behind the router works fine (I am forwarding port 22 on the router to my desktop). However, ssh same.ip.address from within the LAN fails with "Connection refused". ssh 192.168.local.ip.address fails with a different message, "Connection timed out". I can connect if I first ssh to a machine outside the LAN. So far I haven't found anything with Google because with the search terms that seem like they would be relevant, the vast majority of people have the opposite problem - i.e., they can't connect from outside the LAN but can connect within it. I can port forward through a remote server when I'm at home, but this seems like a totally absurd way to connect two computers on the same home LAN. I have already tried stopping and starting sshd on the desktop. Any thoughts?

  Read the article

• How have multiple web servers and IPs on the same physical network

  - by jsigned

  I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• Isolating a computer in the network

  - by Karma Soone

  I've got a small network and want to isolate one of the computers from the whole network. My Network: <----> Trusted PC 1 ADSL Router --> Netgear dg834g <----> Trusted PC 2 <----> Untrusted PC I want to isolate this untrusted PC in the network. That means the network should be secure against : * ARP Poisoning * Sniffing * Untrusted PC should not see / reach any other computers within the network but can go out the internet. Static DHCP and switch usage solves the problem of sniffing/ARP poisoning. I can enable IPSec between computers but the real problem is sniffing the traffic between the router and one of the trusted computers. Against getting a new IP address (second IP address from the same computer) I need a firewall with port security (I think) or I don't think my ADSL router supports that. To summarise I'm looking for a hardware firewall/router which can isolate one port from the rest of the network. Could you recommend such a hardware or can I easily accomplish that with my current network?

  Read the article

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Apache can't get viewed from outside of my LAN

  - by Javier Martinez

  I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

  Read the article

• Different external ip addresses from different sites

  - by user630286

  My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

  Read the article

• Capabilities of business and SOHO routers

  - by Q8Y

  I'm currently studying for the CCNA certifications (especially for Cisco routers and configuration). I know that business routers provide more features than SOHO routers, the processing speed and RAM can be enough. Assume I need to connect a number of users through a network (accessing internet, share files, printers, ...). I have a high speed connection to the internet and I already applied QoS. How can I find out how many users such a single (SOHO) router could handle? In my case I'd attach to it multiple switches until I have the number of ports needed. Would everything work well and smoothly with 50 users? What about 300? At which point would I need a business router instead? If I implemented VLAN here, would it make any difference in the performance? When do I really need to use more than one router? (Both SOHO and business) I'm thinking that I may need them only if I want to increase the performance (instead of replacing the existing one) and if I have multiple locations, so in this situation I need to have multiple routers, right? Put differently: Is there is a need to have another router if my business all in one place?

  Read the article

• Windows 7 'Unidentified Network'

  - by Throdne

  So my internet was working last night before I went to bed and woke up to a computer that is showing unidentified network. I have tried multiple ways of fixing it. > route delete 0.0.0.0 > uninstalling drivers - restart - reinstall from downloaded drivers > ipconfig /release - /renew > static IP > speed & duplex from auto negotiation to 1.0gbps full duplex > and also changed my network address to no value to 1234567890ab (not in that order) nothing seems to work. I have Comcast internet and when I connect the computer to the modem it works perfectly. but when I connect it to my router again, Unidentified network. I know my router isn't faulty, because my macbook pro, server, NAS, iPhones, and iPads are still working. I have also tried moving the port on the router, still same problem. my router is a: Cisco Small Business RVS4000 motherboard: GIGABYTE GA-990FXA-UD3

  Read the article

• Configuring Cisco 877W router from scratch for DHCP, WiFi, ADSL2+, NAT

  - by David M Williams

  Hi all, I apologise if this is a BIG question but I am quite lost with the Cisco IOS. I know what I want to achieve just not how to do it :( I have a Cisco 877W router with 4 FastEthernet interfaces, 1 ATM interface and 1 802.11 Radio. I want to set it up for a small network and am trying to construct a configuration below. I was using Google to try and flesh it out but I think I need help and guidance from actual experts! If it helps, output from show ver says Cisco IOS software, C870 software (C870-ADVSECURITYK9-M), version 12.4(4)T7, release software (fc1) ROM: System bootstrap, version 12.3(8r)YI4, release software Here's what I have so far, which hopefully outlines clearly enough what I am wanting to do. The bits in angle brackets are placeholders (eg the secret password). ! ! Set router hostname ! hostname Shazam ! ! Set usernames and passwords ! username david privilege 15 secret 0 <PASSWORD> enable secret <SECRETPASSWORD> ! ! Configure SSH and telnet access ! line vty 0 4 privilege level 15 login local transport input telnet ssh ! ! Local logging ! logging buffered 51200 warning ! ! Set date and time for NSW, Australia (GMT +10h) ! ! ! Set router IP address to 192.168.1.1 on FastEthernet0 port ! interface FastEthernet0 ip address 192.168.1.1 255.255.255.0 no shut ip nat inside ! ! Forward any unknown DNS requests to Google ! ip dns server ip name-server 8.8.8.8 ip name-server 8.8.4.4 ! ! Set up DHCP ! DHCP pool covers 192.168.1.100 - .199 ! Set gateway and DNS server to be the router, ie 192.168.1.1 ! service dhcp ip routing ip dhcp excluded-address 192.168.1.1 192.168.1.99 ip dhcp excluded-address 192.168.1.200 192.168.1.255 ip dhcp pool <DHCPPOOLNAME> network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 192.168.1.1 lease 7 ! ! DHCP reservations ! ! Assign IP address 192.168.1.105 to MAC address 00-21-5D-2F-58-04 ! ! Configure ADSL2 connection details ! interface atm dsl operating-mode adsl2+ ! ! Set up NAT rules ! ! Forward port 35394 to 192.168.1.105 ! ! Set up WiFi ! ! SSID visible, WPA2 security, Pre-shared key I'm hoping most of this is boiler-plate stuff to you guys. I'm keen to not just get a working script but to actually understand it also. Unfortunately, I'm finding the Cisco reference material online very complex. Thank you!

  Read the article

• Tutorial: Wi-Fi Guru: DD-WRT Router and Wireless Printer

  Q: My Linksys WRT600N flashed with v24 DD-WRT does not work wirelessly with HP7410 all-in-one printer. The printer is able to make a connection, but I cannot ping the printer nor get other programs to recognize it.

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

  - by user135501

  I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start

  Read the article

• BYO Linux router to the NBN

  <b>APC magazine:</b> "What do tomatoes and penguins have to do with the Australian government's nationwide fibre-to-the-home project?"

  Read the article

• Continual "The Windows Filtering Platform has blocked a connection" errors?

  - by Richard

  Our systems have been compromised by something recently which has lead us to carry out a more detailed look at what is happening on our workstations. I have noticed an issue where the Security log of this Windows 7 workstation is continually logging a security "Audit Failure" where the detail is that "The Windows Filtering Platform has blocked a connection". This is happening thousands of times a day and would appear to be our BT Business Broadband HGV 2700 ADSL router attempting to connect to Port 137 (NET Bios) on my workstation and being blocked. This has unfortunately had the effect of filling up the log files so much that anything which might have been of use which was logged over the weekend to help debug the intrusion has been "overwritten off the end" of the Security log. (I've since increased the log file size limits massively and turned on archiving). Does anyone know if this is standard behaviour of a BT ADSL router or whether this indicates that the router is compromised in some way or malfunctioning, or have any further suggestions as to how to diagnose this problem?

  Read the article

• Networking Logs for MAC Addresses

  - by NetworkGuy

  I wanted to ask a multi-part question. Does Comcast Cable Internet services record MAC Addresses of the Router behind the cable modem. I know they record it for the modem itself. But is there a way for the Modem/Comcast to relay and keep logs of the MAC ID of the Router itself? Then does a windows operating system Log the MAC ID of the Router when its connected to it? If so where do I locate and purge this? Please let me know all areas where it is Logged within the operating system. Thank you!

  Read the article

• cannot ssh to computer behind a dd-wrt bridge

  - by Jayaraman

  In my home network , i have dd-wrt router in another room , which bridges wifi from main home router (linksys) to the computers wired behind dd-wrt router. Now I cannot ssh from my laptop ( connected to linksys wifi) to the computers behind dd-wrt wifi bridge. I am able to ping the individual computers behind the dd-wrt bridge. When it comes to ssh or telnet to the computers , it is blocked. What can I do to make dd-wrt bridge to open up all ports in the dd-wrt bridge ?

  Read the article

• Setup Linksys 3200 remote access

  - by Greg

  I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are: When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. Any idea's on what else I have to do to allow remote management access? UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.

  Read the article

• Internet speed is suddenly slow only on my laptop, but it's normal in other devices

  - by Wael

  I have a TP-Link router connected to a ZTE modem, with 2 laptops, a tablet, 2 phones connected via the router's WiFi, and an additional desktop connected via ethernet to the router. Today, my laptop started to have a very slow connection to the internet, which at first I thought it was the operator's problem to find out later on that it works fine on other devices. I tried to connect directly via WiFi to the modem, but it was as slow. I cannot access facebook at all, google takes forever to do a search, and youtube barely works. The weird thing though, is that when youtube does work, the streaming is full speed. This happens also when I download a file! My browse is Firefox, but I used Chrome and IE9 with the same results. I work on Windows 7 Thanks for any advices.

  Read the article

• Need help connecting to NAS externally-port forwarding and DDNS newbie

  - by Joel

  Hi folks, I just picked up a synology NAS, and I'm loving it for internal use, but I want to be able to access the NAS externally-both from my iPhone (3G) and from the net. I have a Linksys WRT54G-TM router. My first question is whether I have set up the dyndns correctly. On my computer that is on my network, if I put in mydomain.dyndns.org, I am taken to a password popup and when I enter my router login and password, my router admin page opens up. On the same computer, I get the same results if I use my external IP address, and if I use my internal IP 192.168.0.1 So that is all as expected. However, when I go to my iphone and turn off wifi, and try to connect with 3g to the external IP or the dnydns domain, I just get an error "Safari could not open the page because the server stopped responding". What's up?

  Read the article

• Can connect to DNS addresses typed in the URL but not by IP addresses

  - by Ben

  I just changed over my modem to bridged mode, and changed my wireless router to PPPoE. My PC IP address is reserved and forwards port 80 to my computer's IP address based on my MAC address. I have a problem, however. I cannot access my local webserver by public IP address or my router 192.168.0.1 wirelessly from any other computer or iPad. I can, however, connect by this PC which is connected to the wireless router via ethernet. Via wireless, it says it cannot connect, however DNS addresses work (e.g. google.com, etc.) Any ideas?

  Read the article

< Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >