Search Results

Search found 741 results on 30 pages for 'superuser'.

Page 26/30 | < Previous Page | 22 23 24 25 26 27 28 29 30  | Next Page >

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• CPU operating temperature ranges

  - by osij2is

  I have an AMD Phenom II 960T with 2 cores unlocked for a total of 6 cores. I don't overclock at all. I have a Arctic Cooling ACALP64 Heatsink/Fan installed. I'm currently running ESXi 5.0 so I have to go into the BIOS to read the CPU temperatures, which at idle seem to be in the 71-74C range. To me, this is pretty high, but I cannot find any official temperature ranges that AMD says the CPU can work well within. There seems to be a lot of questions on superuser and numerous forums around CPU temperatures but no one seems to have a clear consensus as to what the manufacturer temperature ranges are for specific CPUs. I've tried searching through AMDs site to no avail. At this point, I'd be willing to shut off the 2 extra cores if it keeps the heat down but until I get some sort of tolerance or range for temperature, I have no idea if the CPU is being damaged or not. Can anyone point to a direct source, article, FAQ from AMD that specifically states their CPUs temperature range? Or are CPU temperature ranges so varying that there's no possible baseline? Am I being too paranoid about this? To me, anything over 65C is a bit much and if I'm in the low-mid 70s range with NO VMs running, what can I expect if I have several VMs running?

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

• TortoiseSVN client slows Explorer to a crawl in Windows XP running in Parallels

  - by Cory Larson

  I thought I'd make my first SuperUser question relatively simple, though it's the kind of question that may not get many responses as I'm not directly involved with the issue. A colleague does his development in Windows XP running in Parallels on his Mac. We've just migrated our VSS repository to SVN, and we've gone with TortoiseSVN as our client of choice with the Ankhsvn plugin for Visual Studio. On his XP instance, after installing TortoiseSVN, browsing through folders using Explorer is extremely slow; about 15 - 30 seconds before the contents of the next folder displays. It's the slowest when opening My Computer. Once he reaches a folder that contains the working content of an SVN project, Explorer behaves quickly again as expected. It seems that TortoiseSVN may be spending a bunch of time searching subfolders for stuff so it can do its icon-overlay thing, but that's just a guess. I've used TortoiseSVN for years on both XP and Vista on far less powerful machines without any issues with Explorer, so I'm attributing the slowness to it being run in a VM, though that may not be the actual issue. So has anyone encountered similar performance issues, and/or know of a fix? Keep in mind that any requests to make changes to his configuration will need to be communicated and thus my response time might be slow. Thanks everyone!

  Read the article

• Use preforker(ruby gem) with supervisor

  - by user1548832

  I also asked same question on stackoverflow.com http://stackoverflow.com/questions/13871169/use-preforkerruby-gem-with-supervisor But, superuser.com might much help to me. Can anyone amswer this? I want to run a server program using preforker ruby gem with supervisor. But error has occured. I wrote a following test program using preforker. #!/usr/bin/env ruby require 'rubygems' require 'preforker' Preforker.new(:app_name => 'test-preforker', :timeout => 60, :workers => 1) do |master| while master.wants_me_alive? do puts "hello" sleep 10 end end.run And a following supervisor config. [program:test-preforker] command=/home/tkono/tmp/test-preforker.rb stdout_logfile_maxbytes=1MB stderr_logfile_maxbytes=1MB stdout_logfile=/var/log/%(program_name)s.log stderr_logfile=/var/log/%(program_name)s.log autorestart=true Then, reload supervisor. # supervisorctl reload Restarted supervisord Here is the log file of supervisor. 2012-12-13 17:50:47,161 CRIT Supervisor running as root (no user in config file) 2012-12-13 17:50:47,163 WARN Included extra file "/etc/supervisor.d/test-preforker.ini" during parsing 2012-12-13 17:50:47,209 INFO RPC interface 'supervisor' initialized 2012-12-13 17:50:47,213 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2012-12-13 17:50:47,215 INFO supervisord started with pid 12437 2012-12-13 17:50:48,231 INFO spawned: 'test-preforker' with pid 12440 2012-12-13 17:50:48,233 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:49,248 INFO spawned: 'test-preforker' with pid 12441 2012-12-13 17:50:49,261 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:51,267 INFO spawned: 'test-preforker' with pid 12442 2012-12-13 17:50:51,284 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:54,305 INFO spawned: 'test-preforker' with pid 12443 2012-12-13 17:50:54,308 INFO exited: test-preforker (exit status 1; not expected) 2012-12-13 17:50:55,311 INFO gave up: test-preforker entered FATAL state, too many start retries too quickly Please tell me what is wrong? A program using preforker cannot run with supervisor? preforker https://github.com/dcadenas/preforker supervisor http://supervisord.org/index.html

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Windows 7 / TCP/IP network share guide - looking for to resolve failure to mount lacie network drive but works on XP,Linux,Mac.

  - by Rob

  Can anyone advise me of a really good, readable, Windows 7 TCP/IP network share guide, book, or reference. I want this because I cannot mount my Lacie 2big ethernet network drive in Windows 7 (32 bit home), but I can mount it in Windows XP Home 32bit, Ubuntu Linux 10.04 and Apple MacOS X. This drive is being mounted via the accompanying Lacie Ethernet Agent in XP (which I believe uses "Bonjour" protocol), on Mac and Linux it works without further need for software. Another Super User user has the same problem, but no answer: Trouble accessing network drives in Windows 7 I hope my take on the question shows a better willingness to investigate and do some digging - and therefore invite some suggestions to help with this. The drive is detected by Windows 7 (i.e. speech bubble "network drive found") but on trying to open an Explorer window, this remains blank with the Windows busy pointer. I'd prefer not to reinstall Windows 7 to see if that cures the problem, I'd rather understand what is happening/not happening, perhaps even compare differences with Windows XP. Suggestions, please for such guides or even the original problem itself. Update Edit Rewrote question more comprehensively here: Mhttp://superuser.com/questions/304209/looking-for-definitive-answer-to-accessing-a-network-share-via-windows-7-home-and

  Read the article

• Sync, share and backup policy using NAS

  - by Cue

  Trying to come up with a way to keep in sync while sharing and keeping a backup of my music/photos and movies. Currently I have an iMac in Greece and a MBP with me in the UK. As a result I've ended up with 2 iPhoto and iTunes libraries not to mention Documents scattered here and there, user settings etc. I also like to have a backup in case of a drive failure or the need to clean install. It seems that iPhoto and iTunes don't work really well with networked libraries. The way I think about it is to have a NAS where I keep my iTunes and iPhoto library but also rsync daily to my MBP to have a local copy. That way my files are shared across the network as well as act like a backup. In addition I get to have my files wherever I take my MBP but also have the ability to clean install. The tricky part comes from keeping in sync the iMac which is miles away. Again I'm considering a mirror setup (NAS, rsync to the iMac) as well as an rsync between the two NAS. It pretty much resembles the way Dropbox works, sans the requirement to go through their servers but I'm no "superuser" and don't really know if it is even feasible to have such a setup. Looks like there are so many things that can go wrong.

  Read the article

• Local user vs. domain user? What is the right way here?

  - by ebeeb

  I'm a software developer in a company with 6 employees. Everyone has a machine for him-/herself, so none of the machines is shared. I'm currently setting up my machine with Windows 8 and was experimenting a bit with domain and local user accounts. Correct me please if I'm wrong, but I think the idea behind is, that domain users generally should not be able to modify the configuration of a machine (like installing software), since they are able to login on every single machine in the domain. The local user (usually just one local administrator per machine) is the one who cares about the configuration of the machine. But in my case the login into the domain is just for being able to access directories/servers in the domain (I do not really know the details, all I know is, that loggin into the domain user account is necessary). So overall I've got a local admin account and a domain account used on my machine. While working I'm logged in to my domain user account. But it annoys me, that I always need to enter the credentials of my local user account when I'm about to update/install something, which happens quite often as a software developer. I fixed this with adding the domain account into the user accounts in my control panel and putting it into the Administrators group. The only thing I wanted to know about this: is there something REALLY bad about doing this? Or is there maybe a more common way to be able to act like a local admin, while logged in as a domain user? PS: I'm sorry about the tags, but I don't know the proper ones. I'd be glad if some of the superuser experts could fix this :-)

  Read the article

• How can I take browser screenshots at a higher resolution than my browser supports?

  - by user53575

  I need to take a screenshot of a website as it would appear on a very high resolution monitor... say 16000x12800 pixels. My laptop's screen has a native resolution of 1280x800. Basically, I need to simulate having a monitor resolution much higher than my monitor and video card actually supports. I want the screenshot of the site to look pretty much how it does when you hit CTRL MINUS (zoom out) in Firefox repeatedly, but without any loss of pixels due to scaling. How can I do this? Is there some way to use virtual machine software to simulate a super-high-res display? If not, is there some way to open a browser window bigger than the screen, and then capture its contents as a PNG somehow? Anything else that might work? Here was an answer: http://superuser.com/questions/120266/how-can-i-take-browser-screenshots-at-a-higher-resolution-than-my-browser-support But it doesn't work. Firefox remains in the resolution of the physical screen. The window blinks and shrinks back to normal resolution. Please Help!!

  Read the article

• ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

  - by Mark Pim

  I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

  Read the article

• Mac OS X - Time Machine backup fails verification - What can I do to save the history?

  - by usermac75

  Hi, How do I make Time Machine to make a new complete backup without losing older versions of backed up files? Verbose: I am using the Time Machine backup on my OS X (Snow Leopard) to backup the whole computer to an external drive. I especially like the "history", i.e. the feature that allows you to restore the older version of a file. Problem: I had some data corruption on my external backup drive, I repaired it with the System Tool for doing that, it found some faults. I had the disk tool repair the external drive. After that, the external drive was OK and I could use Time Machine again. I let Time Machine do one more backup. Now I made a verification according to http://superuser.com/questions/47628/verifying-time-machine-backups, namely along sudo diff -qr . $HOME/Desktop 2>&1 | tee $HOME/timemachine-diff.log However: After doing the command above, several differences and missing files were reported, approx. 200 files in sum. Whereas some of the missing files were cache or excluded directories, the differences do bother me, especially as some important documents from me are listed as differing. How can I make sure that the data on the external drive is synced correctly? Is it possible to have Time Machine to do a complete new backup without losing the history? Or to have Time Machine compare all files for differences and re-write all files that are different? Or can I set some flags on the files that do not match to have them copied again? (like the archive-flag in Windows/Dos). I'd rather not touch the files because I would like to keep the date of last change/date of creation) Thank you for your thoughts!

  Read the article

• Any ideas why Ettercap filters aren't seeing packet data?

  - by Bryan

  I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• Monitor attached to motherboard is out of frequency

  - by Neilvert Noval

  I don't know if this is appropriate to ask it here in superuser. Please, just route this to appropriate stackexchange site if found unrelevant. Here's my scenario. I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is: Out of frequency. Current frequency is 89Hz. The operating output of my monitor is (around) 60-70Hz. I would like to get this thing work. How can I let my CRT display properly? I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info: My monitor is attached directly to the built-in video adaptor of my motherboard. (No additional video cards) Install of OS is complete without errors. Please help.

  Read the article

• How to make Firefox file associations consistent with Ubuntu file associations?

  - by wbharding

  This seems to be a pretty commonly Google question, but one for which there are no answers. http://www.linuxquestions.org/questions/linux-software-2/firefox-download-mime-types-378902 http://www.birkit.com/content/kubuntu-linux/internet/firefox/fix-file-associations-in-firefox.html Being three links amongst the many. The gist of what I want to accomplish is to have Firefox understand the file associations I download without me having to manually map all of them myself. Gnome knows the file extensions, so I would have expected that Firefox could just use the already-known file mappings there to open the right stuff (as I presume Chrome does). But it doesn't. At least not for me, using Firefox 4, and not by default. When I click on a downloaded file right now, Firefox always has to ask me what application should be used to open the file. A handful of Google results tell me that I can reassociate my file extensions by deleting ~/.mozilla/firefox/[profile name]/mimeTypes.rdf, but while deleting that file does in fact result in a new mimeTypes file being generated, the new mimeTypes is just as barren as the old one had been. Based on the amount of unanswered Qs on the Googlesphere, I know this is a very common problem for Ubuntu users, but it seems to be one for which nobody has chimed in with a good solution. Maybe Superuser can finally be the panacea for us all?

  Read the article

• Firefox url / link to a group of saved bookmarks?

  - by This_Is_Fun

  In Firefox you can easily save a group of tabs together. When (re-)accessing this group, the 'cascading' bookmark menu shows each individual bookmark (and under a line) it says "open all in tabs" I'm looking for a way to launch those tabs without going up through the bookmark menu. Possible options: A) Record a simple macro w/ any number of "superuser" utilities* ('A' is not the preferred option, since many 'little-macros' are hard to keep track of) b) Use Autohotkey (similar to option 'A' and more flexible once you learn the basics) c) How does Firefox load all those tabs? The info must be stored somewhere (as a type of URL??) Quick Summary: The moment I click on "open all in tabs", I am clicking on something very similar to a hyper-link. How do I find the content (exact code) of that 'hyper-link', and / or "How do I easily launch the tabs?" .. . New EDIT #1: I'm looking for a way to launch those tabs without going up through the bookmark menu, or cluttering the bookmarks toolbar which I hide anyway :o) .. . New EDIT #2: I tried to keep the question simple and not mentioning Autohotkey programming. The objective is to launch all tabs using a button on an AHK gui. When grawity said, "It's just an ordinary folder containing ordinary bookmarks," he (she) reminds me I can easily find the folder / Now how to launch to urls inside that folder? .. FYI: (Basic-level) AHK works like this: ; Open one folder ButtonWinMerge_Files: Run, C:\Program Files\WinMerge\ Return .. ; Use default web browser for one link ButtonGoogle: Run, http://google.com Return .. . Question still open: The moment I click on "open all in tabs", I am clicking on something very similar to a hyper-link. "How to 'replicate' the way Firefox launches the tabs with one click?"

  Read the article

• How to correctly set GNU Screen to display currently running program in hardstatus

  - by johnny_bgoode

  I posted this question on SuperUser but it's hardly getting any views, so I thought I'd ask here as well. In bash, to display the name of the current program in the GNU Screen hardstatus line takes only two configuration lines. First, tell screen what the end of your prompt normally looks like, and supply a default title for a window when you are sitting at in the shell: shelltitle "$ |bash" Next, place this escape sequence in the PS1 variable, before the characters that normally terminate the prompt '$ ' in this case: \033k\033\\\ This technique works, to a point. The hardstatus window title is updated to the name of the currently running program, and then switches back to the default title shortly after execution is finished. One major problem, however, is that this escape string is not escaped itself, causing line-wrapping problems with commands longer than the initial line. This was annoying, so I set out looking for a solution. Turns out, simply escaping the previous escape sequence corrects line wrapping: [\033k]\[\033\\\] Great! My hardstatus window title still updates to the name of the currently running program, and now my longer commands wrap to the second line correctly. However, with this new escape sequence in my PS1, screen updates the window title to the actual command I am typing, not simply the name of the current program once it is executed. I am wondering, has anyone gotten this working correctly - i.e. line wrapping and proper updating of the hardstatus window title? Thanks!

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• Vim autocommand on BufDelete prevents opening help window

  - by Kyle Strand

  I have the autocommand described here in my .vimrc: http://superuser.com/a/669463/199803 EDIT: Copied into body of question for convenience: function CountListedBuffers() let cnt = 0 for nr in range(1,bufnr("$")) if buflisted(nr) && ! empty(bufname(nr)) let cnt += 1 endif endfor return cnt endfunction function QuitIfLastBuffer() if CountListedBuffers() == 1 :q endif endfunction autocmd BufDelete * :call QuitIfLastBuffer() Bizarrely, though, it seems that if I have exactly one listed buffer, and I try to use the :help command, the help window fails to open (or perhaps opens and is immediately closed). If I comment out that autocommand line in my .vimrc, this behavior no longer occurs. Why is this happening, and how can I fix it? Why would :h even trigger the BufDelete event? EDIT: setting verbosity to level 12, I can see that the BufDelete event is indeed occurring. Here's the portion of the output that looks relevant to me: Executing BufAdd Auto commands for "*" autocommand call <SID>BMAdd() calling function <SNR>6_BMAdd calling function <SNR>6_BMAdd..<SNR>6_BMFilename calling function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMMunge calling function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMMunge..<SNR>6_BMTruncName function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMMunge..<SNR>6_BMTruncName returning '/usr/local/share/vim/vim74/doc' continuing in function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMMunge function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMMunge returning 'help\.txt\ (4)\^I/usr/local/share/vim/vim74/doc' continuing in function <SNR>6_BMAdd..<SNR>6_BMFilename calling function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMHash function <SNR>6_BMAdd..<SNR>6_BMFilename..<SNR>6_BMHash returning #340582286 continuing in function <SNR>6_BMAdd..<SNR>6_BMFilename function <SNR>6_BMAdd..<SNR>6_BMFilename returning #0 continuing in function <SNR>6_BMAdd function <SNR>6_BMAdd returning #0 continuing in BufAdd Auto commands for "*" Executing BufDelete Auto commands for "*" autocommand :call QuitIfLastBuffer()

  Read the article

• Windows preventing running of Telnet client

  - by palswim

  At first, I had issues because Windows 7 doesn't install the Telnet client by default (also, SuperUser has a thread). So, after installing it (and restarting, like Windows asked, though completely unnecessary), I opened a command prompt, and went to run my new Telnet program. I enter telnet, and receive: C:\Users\[USER]>telnet 'telnet' is not recognized as an internal or external command, operable program or batch file. "That's odd," I think to myself. So, in Windows explorer, I navigate to \Windows\System32 and see telnet.exe sitting in that folder. If I double-click on the executable file, the Telnet command prompt opens for me without a problem. So, I return to my Windows Command Prompt, and enter: C:\Users\[USER]>\Windows\System32\telnet.exe '\Windows\System32\telnet.exe' is not recognized as an internal or external command, operable program or batch file. And then (grep comes from cygwin): C:\Users\ryan\Desktop>dir \Windows\System32 | grep telnet Nothing. I've disabled UAC and have no idea why my Command Prompt is lying to me. Anyone experience something similar? To recap: In Windows 7, I have installed Telnet and can see it in my System32 folder, but cannot run it via a Command Prompt.

  Read the article

• Cisco AnyConnect VPN client - prevent connecting as work network

  - by Opmet

  From Windows 7 I'm using "Cisco AnyConnect Secure Mobility Client 3.0" to connect to our corporate network. Every time I establish the VPN connection Windows will set the type as "work network". I don't want this. So I go to "network and sharing center" and manually / interactively change it to "public network". But I have to repeat it for every new VPN connection. Is there any way to make Windows remember / persist this configuration? Can it be configured in the VPN client? Do our IT admins need to change something at server end? Motivation: A "work network" per default uses different firewall settings that allows for stuff like "network discovery" and "file shares". But I just need "remote desktop" (mstsc). Additional info: Our IT admins claimed this would be Windows default behaviour and there was nothing we could do about it: Windows would always initiate a VPN connection as "work network". Based on this statement I assume this is a "general" issue and went ahead posting here (at superuser.com).

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• query keepalived

  - by tdimmig

  *Note: I have trouble deciding what should go in serverfault and what should go in superuser, if some kindly admin decides this is in the wrong place please move it for me - many thanks. I am implementing a basic HA system with keepalived. I only want to be notified of the failover in the case of hardware failure. I do, however, have the servers switch roles periodically. I have a track_script running on the backup that will vary it's return between 0 and 1 on an interval (once a week, once a month, whatever). Upon returning 0, the priority is raised above that of the master, upon returning 1 the priority is lowered again. This way they trade places on the configured interval. The question: What can I do to tell the difference between a switch caused by my script, and a switch caused because one of the servers died? I certainly want to be notified when there is an actual problem, but not every time the servers change places because of the script. I see that version 1.2.7 has snmp support and I may be able to use it to get some information that could tell me one way or another, but to be honest I've never used snmp before and I don't know how to get the information I want with it (my Google foo failed me).

  Read the article

• Robocopy (without /l flag) running for hours making log file huge, but not actually copying anything

  - by Mickster

  Here's my command: Robocopy C: C:\C_root /FP /BYTES /TEE /S /E /COPYALL /DCOPY:T /MOVE /Z /ETA /XJ /R:2 /W:30 /XF pagefile.sys /XD /LOG:C:\robocopy.log. BTW, notice the /XD option above. After that I had a few directories that I want to omit. I showed these between angle brackets like this: (left angle bracket) a few dirs I wanted to exclude (right angle bracket). Amongst these dirs was the C_root dir itself, so that it did not get into an "infinite" recursion. (This part was stripped from the post because angle brackets apparently have a meta-meaning to superuser.com about hyperlinks.) The command window this was running in listed a few "EXTRA" files then "hung". By this, I mean no more output, no cmnd prompt, and if I tried to scroll it up, it would immediately scroll right back to the bottom. After about six hours, it finally finished, although I never got a cmnd prompt back in the window I started it in. DIR shows the log file at more than 1.3GB, but when I try to do a MORE on it, I get "Cannot access file". C:\C_root never grew larger. Does anyone have an idea what is going on here?

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30  | Next Page >