Search Results

Search found 10169 results on 407 pages for 'port'.

Page 260/407 | < Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >

• IIS not listening over external network, all other traffic working

  - by Beuy

  Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• Connecting to a LDAPS server

  - by Pavanred

  I am working on a development machine and I am trying to connect to my LDAP server. This is what I do - telnet ldaps- 686 then the response is - Could not open connection to the host on port 686 : connect failed But, the strange part is when I connect to my server - telnet ldap- 389 then the connection is successful. My question is, why does this happen? Do I have to install SSL certificate on the client machine where I make the call from? I do not know much about this. I know for a fact that the LDAP server is working fine because other applications are successfully using it currently.

  Read the article

• Methodologies for performance-testing a WAN link

  - by Chopper3

  We have a pair of new diversely-routed 1Gbps Ethernet links between locations about 200 miles apart. The 'client' is a new reasonably-powerful machine (HP DL380 G6, dual E56xx Xeons, 48GB DDR3, R1 pair of 300GB 10krpm SAS disks, W2K8R2-x64) and the 'server' is a decent enough machine too (HP BL460c G6, dual E55xx Xeons, 72GB, R1 pair of 146GB 10krpm SAS disks, dual-port Emulex 4Gbps FC HBA linked to dual Cisco MDS9509s then onto dedicated HP EVA 8400 with 128 x 450GB 15krpm FC disks, RHEL 5.3-x64). Using SFTP from the client we're only seeing about 40Kbps of throughput using large (2GB) files. We've performed server to 'other local server' tests and see around 500Mbps through the local switches (Cat 6509s), we're going to do the same on the client side but that's a day or so away. What other testing methods would you use to prove to the link providers that the problem is theirs?

  Read the article

• I just got a linode VPS a week ago and I've been flagged for SSH scanning...

  - by meder

  I got a 32-bit Debian VPS from http://linode.com and I really haven't done any sort of advanced configuration for securing it ( port 22; password enabled ). It seems somehow there is ssh scanning going on from my IP, I'm being flagged as this is against the TOS. I've been SSHing only from my home Comcast ISP which I run Linux on. Is this a common thing when getting a new vps? Are there any standard security configuration tips? I'm quite confused as to how my machine has been accused of this ssh scanning.

  Read the article

• Sending emails with remote mail server in ASP.NET blocked by Windows firewall?

  - by Dave

  I want to migrate a web application from a Windows Server 2003 to a Windows Server 2008 R2. All works fine except sending emails from the application. If I configure the application to use the smtp server on "localhost" it works, but changing it to the "real" host name (e.g. mail.example.org) no mail is sent. The error message says, that the remote server needs a secure connection or smtp authentication. But since it works when using "localhost" instead of the host name I doubt that this is the problem. Also it's unlikely a problem with the mail server, I also tried it with another one. So for me it seems like the firewall is blocking the outgoing connection to the mail server. I tried to open port 25, but it still did not work. Maybe I just did it the wrong way.

  Read the article

• SSH not working after Restoring Running-Config to a Replacement Cisco Router

  - by Kyle Brandt

  One of my Cisco routers died over the weekend, Cisco sent the replacement and I restored the the config using copy tftp: running-config. Everything seems to work fine but I can no longer ssh into the router (I can telnet). The connection is refused, so it isn't listening on port 22 it seems like. I had previously backed up the config by just doing ssh router 'show run' > backup_config from my workstation. So: Is there anything wrong with my method of backup vs copy running-config tftp:? I know I haven't given any debug information, but is there something typical I need to do to get ssh working?

  Read the article

• vps like [load] graphs

  - by foober

  I investigated a couple of tools but they were really annoying and not polished. kSar for exampe is supposed to graph sar output, but it doesn't work. There's a perl script around (sar2rrd) that's supposed to convert sar output in rrd format and generate graphs. Doesn't work. (at least it doesn't like the output of "atsar" as per debian/ubuntu package). Tried munin but it wants to mess with http servers, and for some reason it didn't really work, too. It displayed errors in the webpage generated by the http server it put on port 4949. So, is there a simple install and forget tool to generate daily load,cpu,memory,network graphs? It seems strange to me that this problem has not been solved, maybe I'm looking in the wrong places

  Read the article

• Windows file sharing connects over WiFi instead of LAN

  - by zacaj

  I have a laptop and a desktop computer, and I need to sync lots of files to the laptop and back whenever I go on a trip, etc. I've got a LAN cable connected into an extra port on the desktop that I plug into the laptop so I can get gigabit file transfers instead of wireless G. They connect fine. If I do an FTP transfer, for instance, using the LAN IP addresses, it goes at ~40MB/s, as it should. However when I copy files using explorer and native windows file sharing it detects the other computer by name, not IP (eg \\DESKTOP-PC\ instead of \\192.168.0.100\) and always connects to it by its wireless IP address instead of the faster LAN address. Both computers are running Windows 7. I have tried editing the priorities of the adapters in Advanced Settings and putting the LAN adapters above the wifi ones, but this didn't have any effect

  Read the article

• Forwarding emails to nonexisting users/aliases to external mail server

  - by Niclas Lindqvist

  I'm in the works of installing a postfix mailserver on a machine currently being used as web server. As of right now, I've got it working as far as that I can send and receive emails using telnet through port 25. However, as my customer is concerned with downtime, I'd like to setup all the accounts one by one over time, and making sure it works, rather than just cutting the cord to the old mail server and start creating new accounts on the new system. How can I add the domain customer.com to my mail server and just add something like [email protected] to the users and aliases-lists without the web server trying to send all emails with the @customer.com domain to the new mail server? I'm running ubuntu, using postfix and postfix-mysql on the new machine, the old mail server is on a hosted environment somewhere else, where I don't have any control.

  Read the article

• Windows Phone 8 not interfacing with Zune software

  - by Cyberherbalist

  I just got a Lumia 521 with Windows Phone 8 and am trying to get the device to work with the Zune software on my PC. I still have my Windows Phone 7 device, and the new one is not working the same way. When I plug the WP7 device into the PC's USB port, it automatically fires up Zune and I can sync my podcasts and music etc to the device. But when I plug the Lumia into the PC it doesn't fire up Zune, and if I start Zune manually, it doesn't interface with the phone at all. Perhaps I am missing something and WP8 isn't supposed to use Zune to interface with the phone?

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• DHCPOFFER delay VLAN

  - by john883

  I have configured two VLANs [ 15 and 16 ] and a trunkport on a Cisco Catalyst 2960. The trunkport is connected to eth2 on a Linux server The server is configured to support VLAN's and the interfaces eth2.15 eth2.16 is configured with ip addresses on two different subnet. dhcp3-server is running on the same server and hands out IP-addresses to the VLANs. When connecting a client to a port that is configured in ex. VLAN 15 and requesting a IP-address, i experience a long delay before recieving a DHCPOFFER, around 30 seconds or so, the client needs to send a DHCPDISCOVER about five times but will always recieve a DHCPOFFER. Any suggestion why this delay is happening?

  Read the article

• Troubleshooting USB Hub on Snow Leopard MacOSX

  - by calmcajun

  I just bought a Belkin F5U701-BLK 7-port USB Hub and when I plug it into my iMac it does not seem to recognize it. Do I need to reboot my machine or install a driver? If I have to install a driver where do I get it from? I tried going to Belkin's website to search for drivers and and support info for the hub but I could not find anything. Edit: The USB hub is powering the other devices but my iMac does not recognize both hard drives.

  Read the article

• Apache on Mac Mavericks issue

  - by Michael

  Trying to run Apache so that I can create a testing server on my mac.When I start apache it starts, but it doesn't run (no connection to local host. Ill upload the unix,you'll see that after starting there is no processes, and I did a check to show you what was running on my port 80... I don't entirely know that means. Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start Michaels-MacBook-Pro-3:~ michaelramos$ ps aux | grep httpd michaelramos 348 0.0 0.0 2442000 624 s000 S+ 8:51AM 0:00.00 grep httpd Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start org.apache.httpd: Already loaded Michaels-MacBook-Pro-3:~ michaelramos$ sudo lsof -i ':80' COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME ocspd 96 root 18u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 20u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 21u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED) ocspd 96 root 23u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED)

  Read the article

• TCP connection stuck in SYN_RECV state despite ACK received, Linux 2.6.18, embedded, ARM

  - by waynix

  My client cannot connect to my protocol port (TCP) after some network glitches, even though all other protocols (telnet/HTTP/FTP) work fine. netstat shows that my server is listening and tcpdump on the server shows all 3 packets are exchanged: 18:29:16.578964 IP 10.9.59.10.3355 10.9.43.131.5084: S 2602965897:2602965897(0) win 65535 <mss 1460,nop,nop,sackOK> 18:29:16.579107 IP 10.9.43.131.5084 10.9.59.10.3355: S 3464857909:3464857909(0) ack 2602965898 win 5840 <mss 1460,nop,nop,sackOK> 18:29:16.579284 IP 10.9.59.10.3355 10.9.43.131.5084: . ack 1 win 65535 But somehow netstat -t shows the connection still in SYN_RECV, as if the ack is not seen by the TCP state machine. I have to restart my server to get it to work. syncookie is not enabled, and I know from client code behavior and tcpdump that there is no SYN flooding. Help much appreciated.

  Read the article

• IPTables reroute traffic not working

  - by user1307079

  I am trying to reroute incoming traffic on my server's port 80 to another server, but it is not working. This is what I tried. On the host server, I ran these: echo “1? > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp --dport 80 -j DNAT --to-destination 38.105.20.226:80 iptables -t nat -A POSTROUTING -j MASQUERADE The server I want it to redirect to is 38.105.20.226:80, but when I go to the webserver that is on the main server, instead of showing the content of the web server on 38.105.20.226:80, it just doesn't load. I am on CentOS.

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• Locking down remote desktop using AD GPO

  - by Brettski

  I am currently locking down a companies remote desktop access via a VPN. What I need to do is disable remote printing, file transfer and clipboard via active directory for the workstations that will be accessed. I am having trouble figuring out which GPO's are used to restrict this. My basic approach is to restrict VPN users to port 3389 so the will be able to access their work computers remotely but nothing else (I will look into layer 7 scanning later). With this I want to ensure they are unable to transfer and data via files, printing or the clipboard. The environment is Windows Server 2003

  Read the article

• Web service not accessible from behind corporates firewalls - how come?

  - by Niro

  We run a Saas serving a widget which is embedded in customer websites. The service include static javascript code hosted on amazon S3 and dynamic part hosted on EC2 with Scalr (using scalr name servers). We received some feedback from users behind corporate firewalls that they cant access our service (while they can access the sites including the widget). This does not make sense to me since the service is using normal http calls on port 80 and our URL is quite new without any reason to be banned by firewalls. My questions are: 1. Why is the service is not accessible and what can I do about it? 2. Is it possible that one of the following is blocked by corporate firewalls: Amazon s3, the dynamic IP address provided by amazon, Scalr name servers. Any other possible reasons, way to check them and remedies for this? Thanks!

  Read the article

• Why shibboleth IdP idp-metadata.xml recommends 8443 for SOAP?

  - by toma

  After the install.sh of 2.4.0 Shibboleth Identity Server, the idp-metadata.xml file is created. Why is that? Is not enough secure to use the standard HTTPS/443 port? <ArtifactResolutionService Binding="urn:oasis:names:tc:SAML:1.0:bindings:SOAP-binding" Location="https://idp.example.com:8443/idp/profile/SAML1/SOAP/ArtifactResolution" index="1"/> <ArtifactResolutionService Binding="urn:oasis:names:tc:SAML:2.0:bindings:SOAP" Location="https://idp.example.com:8443/idp/profile/SAML2/SOAP/ArtifactResolution" index="2"/> <SingleLogoutService Binding="urn:oasis:names:tc:SAML:2.0:bindings:SOAP" Location="https://idp.example.com:8443/idp/profile/SAML2/SOAP/SLO" /> <AttributeService Binding="urn:oasis:names:tc:SAML:1.0:bindings:SOAP-binding" Location="https://idp.example.com:8443/idp/profile/SAML1/SOAP/AttributeQuery"/> <AttributeService Binding="urn:oasis:names:tc:SAML:2.0:bindings:SOAP" Location="https://idp.example.com:8443/idp/profile/SAML2/SOAP/AttributeQuery"/> Thanks, Tamas

  Read the article

• Can you specify git-shell in .ssh/authorized_keys to restrict access to only git commands via ssh?

  - by Matt Connolly

  I'd like to be able to use a ssh key for authentication, but still restrict the commands that can be executed over the ssh tunnel. With Subversion, I've achieved this by using a .ssh/authorized_keys file like: command="/usr/local/bin/svnserve -t --tunnel-user matt -r /path/to/repository",no-port-forwarding,no-agent-forwarding,no-X11-forwarding,no-pty ssh-rsa AAAAB3NzaC1yc2EAAAABIetc... I've tried this with "/usr/bin/git-shell" in the command, but I just get the funky old fatal: What do you think I am? A shell? error message.

  Read the article

• Slow LAN transfer from 3rd party computer

  - by Chris

  Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

  Read the article

• RJ45 female to male fault

  - by GeoPhoenix

  i have the following - common - problem, on one end of the cable, there are RJ45 males T586 A which are connected to a 8-port switcher, on the other end, there supposed to be RJ45 females _T586 A which in turn will allow another RJ45 male to be connected. the commonly used color scheme was followed on males (having the head down) blue white blue orange white green green white orange brown white brown the problem i believe is located on female end of cable, which i try multiple time to follow the numbers designated by the module, which is the list above in reverse, and as listed resulting in no signal transmission. tried the T586B (both ends) for device to device once, but no results. Which is the proper way of handling this wiring? There were also additional RJ45 females with the numbers 6-5-4-3, but 1 to 8 isn't supposed to be used for this?

  Read the article

< Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >