Search Results

Search found 8343 results on 334 pages for 'report generation'.

Page 260/334 | < Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >

  • iSCSI, failover and XenServer

    - by jemmille
    I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

    Read the article

  • How do I install an rpm that complains about rpmlib(FileDigests) <= 4.6.0-1?

    - by Jake
    Im trying to install an rpm file on CentOS 5 and Im not sure how to resolve this issues it brings up: $ rpm --install epel-release-6-5.noarch.rpm warning: epel-release-6-5.noarch.rpm: Header V3 RSA/SHA256 signature: NOKEY, key ID 0608b895 error: Failed dependencies: rpmlib(FileDigests) <= 4.6.0-1 is needed by epel-release-6-5.noarch rpmlib(PayloadIsXz) <= 5.2-1 is needed by epel-release-6-5.noarch What do the lines rpmlib(FileDigests) <= 4.6.0-1 mean? is rpmlib out of date or FileDigests out of date? Whats with the syntax of something followed by parentheses? Ive tried to use yum so that it can resolve dependencies automatically but it is unable: $ sudo yum --nogpgcheck install epel-release-6-5.noarch.rpm ... Running rpm_check_debug ERROR with rpm_check_debug vs depsolve: rpmlib(FileDigests) is needed by epel-release-6-5.noarch rpmlib(PayloadIsXz) is needed by epel-release-6-5.noarch Complete! (1, [u'Please report this error in https://bugzilla.redhat.com/enter_bug.cgi?product=Red%20Hat%20Enterprise%20Linux%205&component=yum']) On this page https://bugzilla.redhat.com/show_bug.cgi?id=665073, they say my rpm is out of date but then say I should request an rpm file that works with my version of rpm (which is 4.4.2.3) but I don't want to do that. How do I make my system compatible with this rpm file? Bonus points if you tell me how I can fix the public key error.

    Read the article

  • Desktop SATA drives in SATA <-> FC array

    - by chris
    Let's assume you've got a box like one of these with space for 24 SATA disks. What are the best bits of advice for deploying this? For instance, should you be greedy and go for the 1.5 or 2tb disks or are they just not reliable enough to be used in an array like this and you should stick with 640gb or 750gb disks instead? Also, I know that FC (or generically, "enterprise class") disks have a different error recovery strategy than desktop disks. An enterprise disk will fail a read quickly and report to the controller that it wasn't able to read that block, and the RAID controller will quickly regenerate the info from the parity disk and mark the block as bad. A desktop disk, on the other hand, will try and try and try again to get the data, and in pathological cases this may cause a raid controller to fail the whole disk because the read operation times out. So there are a couple aspects to this question: What's the best sort of disk to get today? (ie specific disks on the market in Feb 2010) Generically, what should someone look for when trying to buy something like this that kinda walks the line between enterprise and consumer? Lastly -- is there anything that can be done with current "consumer" disks to make them more suitable for array use? IE can you use a SMART configuration to change the error recovery strategy used by the disk? Thanks!

    Read the article

  • Wacom consumer tablet driver service may crash while opening Bamboo Preferences, often after resuming computer from sleep

    - by DragonLord
    One of the ExpressKeys on my Wacom Bamboo Capture graphics tablet is mapped to Bamboo Preferences, so that I can quickly access the tablet settings and view the battery level (I have the Wireless Accessory Kit installed). However, when I connect the tablet to the computer, in wired or wireless mode, and attempt to open Bamboo Preferences, the Wacom consumer tablet driver service may crash, most often when I try to do so after resuming the computer from sleep. There is usually no direct indication of the crash (although I once did get Tablet Service for consumer driver stopped working and was closed), only that the cursor shows that the system is busy for a split second. When this happens, the pen no longer tracks on the screen when in proximity of the tablet (even though it is detected by the tablet itself); however, touch continues to function correctly. To recover from this condition, I need to restart the tablet driver services. I got tired of having to go through Task Manager to restart the service every time this happens, so I ended up writing the following command script, with a shortcut on the desktop for running it with elevated privileges: net stop TabletServicePen net start TabletServicePen net stop TouchServicePen net start TouchServicePen Is there something I can do to prevent these crashes from happening in the first place, or do I have have to deal with this issue until the driver is updated? Windows 7 Home Premium 64-bit. Tablet drivers are up to date. Technical details Action Center gives the following details about the crash in Reliability Monitor: Source Tablet Service for consumer driver Summary Stopped working Date ?10/?15/?2012 2:48 PM Status Report sent Description Faulting Application Path: C:\Program Files\Tablet\Pen\Pen_Tablet.exe Problem signature Problem Event Name: APPCRASH Application Name: Pen_Tablet.exe Application Version: 5.2.5.5 Application Timestamp: 4e694ecd Fault Module Name: Pen_Tablet.exe Fault Module Version: 5.2.5.5 Fault Module Timestamp: 4e694ecd Exception Code: c0000005 Exception Offset: 00000000002f6cde OS Version: 6.1.7601.2.1.0.768.3 Locale ID: 1033 Additional Information 1: 9d4f Additional Information 2: 9d4f1c8d2c16a5d47e28521ff719cfba Additional Information 3: 375e Additional Information 4: 375ebb9963823eb7e450696f2abb66cc Extra information about the problem Bucket ID: 45598085 Exception code 0xC0000005 means STATUS_ACCESS_VIOLATION. The event log contains essentially the same information.

    Read the article

  • Nameserver configuration error (Stealth NS records)

    - by Saif Bechan
    Hello i have a nameserver with a primary domain configured. Now i added a second domain, I have set NS records of the second domain to use the first domain, but i get some strange error. When i do the nameserver check at SIDN, for domains in the netherlands, i sais everything is right configured: Errors=0, Warnings=0, Informational=3 ** Summary: ACCEPTED centshopper.nl. ** Full check report: primary name server "ns1.rdshosting.nl." Info: name server looks correctly configured. secondary name server "ns2.rdshosting.nl." Info: name server looks correctly configured. secondary name server "ns3.rdshosting.nl." Info: name server looks correctly configured. ** DNScheck 4.2.6, 2010/03/12 23:19:58 CET+0100 Now when i check my dns settings over at http://intodns.com/centshopper.nl i get the following 2 errors: 1) Missing nameservers reported by parent FAIL: The following nameservers are listed at your nameservers as nameservers for your domain, but are not listed at the parent nameservers (see RFC2181 5.4.1). You need to make sure that these nameservers are working.If they are not working ok, you may have problems! ns3.rdshosting.nl 2) Stealth NS records sent Stealth NS records were sent: ns3.rdshosting.nl I am running plesk icw centos. In my opinion everything is ok. Does anyone know of this error and know what the possible cause would be. I have checked the first few hits on google already, and can't come up with a working solution. On a sidenote, can anyone explain to me what GLUE is and why i am not getting any. If you have been, thanks for reading!

    Read the article

  • DirectAccess Server firewall rules blocking ports

    - by StormPooper
    I have configured DirectAccess on my Server 2012 Essentials box and most of it works great - I can remotely access the server via RDP and the default IIS website on port 80. However, I can't access anything that uses other ports. For this example, the Team Foundation Server website. The only way to access it is by accessing http://localhost:8080/tfs on the server directly - even when using http://servername:8080/tfs or http://192.168.1.100:8080/tfs won't work. I've tried adding the ports to the NAT exceptions using Set-NetNatTransitionConfiguration –IPv4AddressPortPool and while that has allowed some ports used internally (Deluge, for example) it hasn't allowed me access to the URL. I think I've narrowed it down to the "DirectAccess Server Settings" Group Policy that is created when configuring DirectAccess. When I disable the link for this GPO, the TFS site works again, but the default IIS site stops working (but RDP still works). I already have rules in the firewall on the server for TFS and before enabling this Group Policy (so before configuring DirectAccess) I could access both sites. Does anybody have any suggestions for things I can change to allow access to both? I've uploaded the full GPO report and my Remote Access Configuration Summary for more details.

    Read the article

  • Squid configuration for proxy server

    - by Ian Rob
    I have a server with 10 ip's that I want to give access to some friends via authentication but I'm stuck on squid's config file. Let's say I have these ip's available on my server: 212.77.23.10 212.77.1.10 68.44.82.112 And I want to allocate each one of them to a different user like so: 212.77.23.10 goes to user manilodisan using password 123456 212.77.1.10 goes to user manilodisan1 using password 123456 68.44.82.112 goes to user manilodisan2 using password 123456 I managed to add the passwords and authentication works ok but how do I do to restrict one user to one of the available ip's? I have a basic setup from different bits I found over the internet but nothing seems to work. Here's my squid.conf (all comments are removed to make it lighter): acl ip1 myip 212.77.23.10 acl ip2 myip 212.77.1.10 tcp_outgoing_address 212.77.23.10 ip1 tcp_outgoing_address 212.77.1.10 ip2 http_port 8888 visible_hostname weezie auth_param basic program /usr/lib/squid/ncsa_auth /etc/squid/squid-passwd acl ncsa_users proxy_auth REQUIRED http_access allow ncsa_users acl all src 0.0.0.0/0.0.0.0 acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl to_localhost dst 127.0.0.0/8 acl SSL_ports port 443 # https acl SSL_ports port 563 # snews acl SSL_ports port 873 # rsync acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl Safe_ports port 631 # cups acl Safe_ports port 873 # rsync acl Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access deny all icp_access allow all hierarchy_stoplist cgi-bin ? access_log /var/log/squid/access.log squid acl QUERY urlpath_regex cgi-bin \? cache deny QUERY refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern . 0 20% 4320 acl apache rep_header Server ^Apache broken_vary_encoding allow apache extension_methods REPORT MERGE MKACTIVITY CHECKOUT hosts_file /etc/hosts forwarded_for off coredump_dir /var/spool/squid

    Read the article

  • MS Access 2003 - Format a Number with Commas AND Auto-Decimal

    - by Emtucifor
    On a report I have a control which is bound to a column which can have up to 3 decimal places. I want the number to format with commas separating thousands and millions, but I also want the number of decimal places to be automatic, so that if there is no decimal portion then no decimal at all is shown. 1234.567 -> 1,234.567 1234.560 -> 1,234.56 1234.500 -> 1,234.5 1234.000 -> 1,234 General format will give me the auto decimal places but no commas. Standard format gives the comma but is fixed to 2 decimal places. Doing my own =Format(Number, "#,##0.#") leaves the decimal point in and doesn't align properly, with extra space on the right of the number. Do I have to write my own VB function to give the format I want? It seems silly that Access (apparently) can't do this out of the box. This also seems really horrible: =Replace(Replace(Replace(Replace(Replace( _ Format(Number, "#,##0.000") & "x", "0x", ""), "0x", ""), "0x, ""), ".x", ""), "x", "")

    Read the article

  • mysqld crashes on any statement

    - by ??iu
    I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

    Read the article

  • Subversion gives Error 500 until authenticating with a web browser

    - by Farseeker
    We used to use Collabnet SVN/Apache combo on a Windows server with LDAP authentication, and whilst the performance wasn't brilliant it used to work perfectly. After switching to a fresh Ubuntu 10 install, and setting up an Apache/SVN/LDAP configuration, we have HTTPS access to our repositories, using Active Directory authentication via LDAP. We're now having a very peculiar issue. Whenever a new user accesses a repository, our SVN clients (we have a few depending on the tool, but for arguments sake, let's stick to Tortoise SVN) report "Error 500 - Unknown Response". To get around this, we have to log into the repo using a web browser and navigate 'backwards' until it works E.G: SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/ - Forbidden 403 (correct) Webbrowse to https://svn.example.local/SVN/MyRepo/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) It seems to require authentication up the tree, starting from the svnparentpath up through to the module required. Has anyone seen anything like this before? Any ideas on where to start before I ditch it back to Collabnet's SVN server?

    Read the article

  • 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

    - by Nathan Taylor
    I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

    Read the article

  • How to replicate Lynda.com transitions in my own presentations (Keynote preferred, Powerpoint possib

    - by jdmuys
    I recently noticed that lynda.com uses in their training videos a very interesting transition that I would like to replicate in my own presentations. They are somewhat similar to the computer screen animations in the "Minority Report" movie: they zoom out to a huge sheet, pan, and zoom back in to a new location. It's very good for navigating deep hierarchies. For example when you are at level 1, you can see level 3, but it's tiny and unreadable. You then transition by zooming in to a deeper level that suddenly becomes legible. I can imagine also to use it using a large "mind map" as a common Ariane thread, to dive into details (and back out) while still taking advantage of the visual memory of the audience. It a bit difficult to describe, I hope I managed to convey the idea. You can see them in action for example there (iPhone programming training): http://www.lynda.com/home/DisplayCourse.aspx?lpk2=48369 Then click on "What you should know" in the introduction chapter. See for example in that movie between 22s and 24s, then between 27s and 28s. How do they do that? How could I replicate that effect? TIA

    Read the article

  • Open Office crashes, recovers, crashes again

    - by Daniel R Hicks
    After completely reinstalling my laptop due to apparent registry corruption, I've encountered a problem with Open Office: I open a simple Calc spreadsheet, it comes up normally, but then after anywhere from 5 seconds to several minutes (without even touching the Calc window) OO crashes, then comes up through recovery. If I let it "recover" it will do so and bring the spreadsheet up again, only to repeat the crash scenario again. If I kept clicking "OK" it would apparently do this all day. I reinstalled OO once and the problem went away for awhile, but it came back. I then attempted to "reset" my profile (ie, rename the OO user directory in App Data), but OO crashed during the first startup after that, then resumed the original behavior. If I open the same file using Excel it complains of errors in the file, and "recovers" them, but the "error report" it generates contains no details. If I save the "recovered" file then OO Calc will open it, but the problem returns after saving again. Any ideas? (The system is Vista SP2, running OO 3.4.1) How to reproduce: Start Open Office Calc. Save workspace as "CrashTest.ods" From Task Manager kill Open Office (soffice.exe/bin -- one of each) Double click on the saved "CrashTest.ods" in Explorer. OO puts up a message that recovery will occur -- allow it. When the Calc window comes up, don't touch it -- just wait about 10 seconds. Calc window closes and OO puts up a message that recovery will occur -- from now on the sequence will repeat. I suspect this behavior is limited to a few (recent) versions of OO, and very possibly only Calc. Reported as Open Office Bug 1211094. Sigh!! As much as it irritates me, I'm having to switch over to Excel for several things I used to do with Calc. Excel has a miserable UI, but at least it says up for longer than 10 seconds.

    Read the article

  • MacBook Pro battery capacity 65K mAh

    - by Alexander Gladysh
    I have a 15" MacBook Pro 3.1 (that is Late 2007 model AFAIR). I've bought it new a couple of years ago. Recently its on-battery power lifespan became very short (30 to 10 minutes). When my notebook turns itself off due to "low battery" and I press the small button on the battery itself, all LED lights are alight, indicating full charge. When I plug in the power adapter, my Mac displays that "battery is fully charged, finishing charging process" (I have a Russian OS X 10.5.7, so that is a rough translation), but the LEDs on battery itself display (seemingly accurate) status that there are one or two "LEDs still not charged". My battery have as few as 37 recharge cycles (yes, I've neglected calibration over the time I've used it). Battery info programs like iBatt2 report battery capacity of 65 337 mAh (with by-design capacity of 5600 mAh). I get it that something went wrong with battery electronics. I've tried resetting my Mac's PRAM and SMC, it did not changed anything. Now I'm trying to recalibrate the battery, but looks like it does not help as well. Will try to recalibrate it several times in a row. I'd buy a new battery if I knew if it is battery fault, not a notebook's. Any suggestions? Update: After recalibration, my battery status now displays battery capacity of 1500 mAh. But with every recalibration (or simply when I use notebook without power adapter plugged in) this number changes in the range from 200 mAh to 1700 mAh. LEDs on battery now are synchronous with what nodebook thinks on the charge level. Also I've noticed that cycle count changes rather slowly. It is now 39, it was 37 when I've started recalibration, and I went through the process at least ten times... So, the main question is: does it look like that replacing the battery would help me (or does it look like this is notebook's problem)? I guess I should try replacing the battery.

    Read the article

  • get-eventlog issue

    - by Jim B
    I wanted to get a quick report of some log entries I saw on a server, so I ran: Get-Eventlog -logname system -newest 10 -computer fs1 | fl I got events back however the descriptions were all wrong. Here's an example: Index : 1260055 EntryType : Warning InstanceId : 2186936367 Message : The description for Event ID '-2108030929' in Source 'W32Time' cannot be found. The local compute r may not have the necessary registry information or message DLL files to display the message, or you may not have permission to access them. The following information is part of the event:'time. windows.com,0x1' Category : (0) CategoryNumber : 0 ReplacementStrings : {time.windows.com,0x1} Source : W32Time TimeGenerated : 1/25/2010 10:43:31 AM TimeWritten : 1/25/2010 10:43:31 AM UserName : Note that if I pull the event ID property it's correct (in this case 38) Is this is known issue or is something wrong. The messages resolve fine via event viewer locally and remotely Here is the powershell version info: Name : ConsoleHost Version : 2.0 InstanceId : bc58fcf8-bba3-4ca8-8972-17dbd5d9ff08 UI : System.Management.Automation.Internal.Host.InternalHostUserInterface CurrentCulture : en-US CurrentUICulture : en-US PrivateData : Microsoft.PowerShell.ConsoleHost+ConsoleColorProxy IsRunspacePushed : False Runspace : System.Management.Automation.Runspaces.LocalRunspace Here is the revised version info: Name Value ---- ----- CLRVersion 2.0.50727.3603 BuildVersion 6.0.6002.18111 PSVersion 2.0 WSManStackVersion 2.0 PSCompatibleVersions {1.0, 2.0} SerializationVersion 1.1.0.1 PSRemotingProtocolVersion 2.1

    Read the article

  • Tools to (privately) annotate/markup a website for maintenance

    - by rob
    I've been tasked with updating a website. Rather than proofreading and updating each page (one at a time), I want to make a single pass over the entire website, marking graphics/images/videos that need to be rewritten, removed, or updated. I thought about taking screenshots, marking those up, and putting them in our bug-tracking database, but that seems like an extremely tedious solution. Some of the content is similar on various pages across the website, and the entire site itself is localized into several languages (so any changes made to the English version will have corresponding changes for other languages). I also want all of my markup to remain private (that is, if it's stored online somewhere, I should be the only person who can see my comments). I found an article that lists several website annotation services, but it's not clear whether they allow private annotations, or whether these tools are even appropriate for website maintenance (many of them look more geared toward social networking). I've started making a list of some necessary and desired features below, and may add more as necessary. Annotations/markup/comments remain private (only visible to me) Comment history/tagging (so I can reuse the same comment for shared footers, items requiring similar updates, etc.) Ability to print/export a list or report of all comments for the entire website Ability to produce a categorized list of changes (e.g., to produce a list of images that need updating, which I can send to the graphic designer) What processes and tools do you use to keep track of all the changes that need to be made to a website? What features are painfully absent from the tools you use?

    Read the article

  • kvm works only when kvm-intel is unloaded

    - by Sathya
    I am new to kvm. I have this strange issue. But before explaining the issue, here is my set up. I try to install VM on my Host which is a Acer Laptop 5720 Has T7500 Intel processor. The cpu flags indicate that Virtualization is supported. I run Ubuntu 10.04 (lucid) on it. It comes with kvm. Now coming to the issue - I dont get any errors while executing "sudo modprobe kvm-intel". So I presume my processor does indeed support hardware virtualization. I use virt-manager and create a VM on which I install ubuntu from an *.iso file. When I start the VM it says it is running. No signs of any trouble. I can see the domain list in "virsh list". But when I try to connect to the VM thru VNC, all I get to see is a blank screen (no cursor). There is no response to any key press. I changed the video mode etc. Tried all different combinations but none work. But strangely, if I shutdown the vm an virt-manager and then unload the module by doing "sudo modprove -r kvm-intel", everything works fine. ie., I can see the screen via VNC. I am able to install the OS and so on. So what does this mean ? IS hardware virtualization not supported ? How come there is no error anywhere ? dmesg | grep kvm doesnt report anything. Can someone throw light on what excatly is happening ?

    Read the article

  • Postgresql server will not start

    - by Claudiu
    I'm on Windows 7. I restarted my computer. I then tried to connect to the database and got an error. I don't remember which one in particular but it was some connection issue. I decided to try to restart the server, so I clicked on "Restart server" from the start menu. This blocked. After a few minutes I killed the process and tried again, only to get a "The service is starting or stopping. Please try again later." message. I rebooted the computer again, tried to start again, and got the same error. I killed the pg_ctl process and tried starting it manually, but that didn't work either: C:\Users\DrClaud>cscript "C:\Program Files\PostgreSQL\8.3\scripts\serverctl.vbs" start wait Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. The PostgreSQL Server 8.3 service is starting................................... ....................................... The PostgreSQL Server 8.3 service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534. The start command returned an error (2) Any ideas?

    Read the article

  • Why does my Belkin wireless router has eMule port open?

    - by Jeremy Powell
    I have a Belkin F6D4230-4 v1 router. When I port scan it with nmap I get the following: $ sudo nmap -sS -A -T5 192.168.2.1 -p- Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-17 11:40 CDT Interesting ports on 192.168.2.1: Not shown: 65532 closed ports PORT STATE SERVICE VERSION 80/tcp open http Belkin 2307 wifi router http config (IP_SHARER httpd 1.0) |_ html-title: '+i1+' 4661/tcp filtered unknown 4662/tcp filtered edonkey MAC Address: 00:22:75:5D:52:D8 (Belkin International) Device type: WAP|broadband router|firewall|printer|specialized|webcam Running (JUST GUESSING) : Linksys embedded (95%), TRENDnet embedded (95%), Netgear embedded (92%), Canon embedded (89%), On Time RTOS (89%), Symantec embedded (89%), D-Link embedded (86%), Polycom embedded (85%) Aggressive OS guesses: Linksys WRT54GC or TRENDnet TEW-431BRP wireless broadband router (95%), TRENDnet TW100-BRF114 broadband router (95%), Netgear FR114P ProSafe VPN firewall (92%), Canon PIXMA MX850 printer (89%), On Time RTOS (89%), Symantec Firewall/VPN 100 (89%), D-Link DI-714P+ wireless broadband router (86%), Polycom ViewStation video conferencing system (85%) No exact OS matches for host (test conditions non-ideal). Network Distance: 1 hop Service Info: Device: WAP OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 21.57 seconds Why are the 4461 and 4462 ports open? This is a basic, out-of-the-box installation.

    Read the article

  • Latency between IIS and SQL on same physical, two VMs

    - by Jerad Rose
    I have a single server (2x4 core CPUs, 32GB ram), that is a Windows Server 2012 Hyper V host, and it hosts two guest VMs (also Windows Server 2012 instances). One of them is a web server, the other is a SQL server. When hitting a page that loops over 50 records, there is noticeable latency. I capture/report the timings of each iteration on the loop, and each iteration is about 20-30 milliseconds. Of course, this amounts to over a second of latency for the whole loop. I thought maybe SQL needed to be tuned, but running profiler on it, the queries are showing almost 0 duration, so it seems the bottleneck is in transit between the two VMs. I have both VMs configured to use the actual NIC (vs. using a VNIC), so maybe that's part of my problem. Also, this is a classic ASP site, so it's using the SQL OLE DB provider, and I'm wondering if that is part of the problem. This is a new server setup, from an existing Windows 2003/IIS6 server setup where both web and DB run on the same server instance (no virtualization). On that setup, there is no such latency when looping over the cursor like this. But there are so many variables, I'm not sure where to start ruling things out.

    Read the article

  • New 3TB HDD, can see full 2.7TB in Linux and Windows, but shows up as 801.6GB in BIOS

    - by Ben Lee
    I recently purchased a Seagate Barracuda 3TB drive (ST3000DM001). After installing it, my BIOS recognized it but reported the size as 801.6gb. I went ahead and booted into Linux anyway (Ubuntu 11.10 64-bit). Linux saw it as a 2.7TB. Following some online instructions (don't have the link handy, unfortunately), it looks liked converting this drive to GPT was recommended. So I used gparted to do that, then formatted it to NTFS also using gparted. (I'm using NTFS because my machine is daul-boot and I want to have access to the drive in Windows too). I rebooted to Windows (Windows 7 64-bit), and Windows also sees the drive with 2.7TB free. Everything seems to be working fine. The only issue is that my BIOS is still reporting the drive as 801.6GB. My motherboard is an ASRock 770 Extreme3 and BIOS is the latest version. Since everything seems to be working with the new drive anyway, I'm hoping that the fact that the BIOS is reporting the wrong size is not an actual problem. But honestly, I don't really know. Anyone out there more familiar with this know if this could potentially cause any problems in the future? Any way to get the BIOS to report the correct size?

    Read the article

  • Probelms Intstalling Trac using apt-get Ubuntu Jaunty

    - by Ben Waine
    Hi, I'm having some issues getting apt to install trac correctly on my Ubuntu Jaunty Box. Using the command 'apt-get install trac' I get the following output: root@myserver:~# apt-get install trac Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. Since you only requested a single operation it is extremely likely that the package is simply not installable and a bug report against that package should be filed. The following information may help to resolve the situation: The following packages have unmet dependencies: trac: Depends: python-setuptools (> 0.5) but it is not installable Depends: python-pysqlite2 (>= 2.3.2) but it is not going to be installed Depends: python-subversion but it is not installable Depends: libjs-jquery but it is not installable Recommends: python-pygments (= 0.6) but it is not installable or enscript but it is not installable Recommends: python-tz but it is not installable E: Broken packages I have successfully used the command on my karmic kola desktop machine and am able to create new projects etc. I thought I might be able to solve the problem by installing all python related extensions. This produced a very similar output. I have Main, universe and multi-verse repositories enabled. Its a remote machine and I have no access to the gui. Hope someone can help, googleing failed to solve the issue or find a solution! Thanks, Ben

    Read the article

  • Apache & SVN on Ubuntu - Post-commit hook fails silently, pre-commit hook “Permission Denied”

    - by 113169587962668775787
    I've been struggling for the past couple days to get post-commit email notifications working on my SVN server (running via HTTP with Apache2 on Ubuntu 9.10). SVN commits work fine, but for some reason the hooks are not being properly executed. Here are the configuration settings: - Users access the repo via HTTP with the apache dav_svn module (I created users/passwords via htpasswd in a dav_svn.passwd file). dav_svn.conf: <Location /svn/repos> DAV svn SVNPath /home/svn/repos AuthType Basic AuthName "Subversion Repository" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user </Location> I created a post-commit hook file that writes a simple message to a file in the repository root: /home/svn/repos/hooks/post-commit: #!/bin/sh REPOS="$1" REV="$2" /bin/echo 'worked' > ${REPOS}/postcommit.log I set the entire repository to be owned by www-data (the apache user), and assigned 755 permissions to the post-commit script when I test the post-commit script using the www-data user in an empty environment, it works: sudo -u www-data env - /home/svn/repos/hooks/post-commit /home/svn/repos 7 But when I commit on a client machine, the commit is successful, but the post-commit script does not seem to be executed. I also tried running a simple script for the pre-commit hook, and I get an error, even with an empty pre-commit script: "Commit failed (details follow): Can't create null stdout for hook '/home/svn/repos/hooks/pre-commit': Permission denied" I did a few searches on Google for this error and I presume that this is an issue with the apache user (www-data) not having adequate permissions, specifically to execute /dev/null. I also read that the reason post-commit fails silently is because that it doesn't report with stdout. Anyway, I've also tried giving the apache user (www-data) ownership of the entire repository, and edited the apache virtualhost to allow operations on the server root, and I'm still getting permission denied /etc/apache2/sites-available/primarydomain.conf <Directory /> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> Any ideas/suggestions would be greatly appreciated! Thanks

    Read the article

  • Explorer and open file dialog not responding (Vista)

    - by rohancragg
    Any explorer window opened for the first time on my machine causes the explorer window to display the folders tree and folder path in the address bar immediately but the file/folder list pane is blank and the window displays 'Not Responding' in the title bar, this hangs for up to a minute or more. Any file dialog displays 'Not Responding' in the title bar. The files list is eventually displayed after a few seconds or more. Steps to repro: Close all open instances of explorer Windows Key | Run | [enter a folder path such as 'c:\temp'] Or within any app: use a file open / save dialog Once there is at least one open instance of explorer the performance is still fairly poor but not nearly so bad and file lists are displayed in a timely fashion. What I've tried: Cleaned up registry with CCleaner tool, and uninstalled all other unused software Checked nothing unwanted running at startup with Autoruns Removed any ISO burner/recorder/mount software Still to try Get latest version of everything - especially stuff with shell extension behaviour such as TortoiseSVN Anyone have any other suggestions? Thanks alot. Update I'm wondering if this is related, I'll try the hotfix when I get home and report back: KB972685 - FIX:Explorer.exe hangs when using a shell extension written using MFC Update 2 Before I got a chance to try the hotfix it seems one of the above actions fixed this for me; either the removal of IsoRecorder or TortoiseHg (which I was no longer using anyway). Update 3 A similar issue with Explorer.exe has come back since installing TortoiseHg 1.01 :-(

    Read the article

  • One host on a network can't connect to one other host

    - by Max Williams
    I'm on a local network with a few other people. On of the hosts is a virtual machine running in virtualbox on a mac, which has the ip address 192.168.0.35 (the VM that is, not the mac host). Everyone except one guy can connect (ie ping, ssh etc) to that machine. When that one guy tries to ping it he gets Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 which i understand is just how certain mac os's report an unreachable connection. He can ping all the other hosts on the network, ie our computers, and we can all ping the VM fine and connect to it with no problems etc. His ip is 192.168.0.17. I ssh'd onto his machine (as a new user 'anon') and saw the same problems. I can ssh onto the 192.168.0.35 VM as well. From there, i can ping other users, but when i ping the problem guy, it's unreachable that way round as well. He restarted his mac, and was fine for a while. Then, just stopped working again. He's got a different IP to before. Any ideas, anyone? Don't know enough about this stuff to even diagnose the problem. thanks, max

    Read the article

< Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >