Search Results

Search found 6815 results on 273 pages for 'micro sd card'.

Page 261/273 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• installing windows XP in Samsung SENS 145 plus notebook (no CD drive)

  - by user13267

  Hi I was trying to install Windows XP in a Samsung SENS 145 plus Notebook. It does not have a cd drive and I already managed to format it and semi install Windows XP, so now it does not even boot up either. This is what I did: Since it supports USB booting, I first made a bootable USB of Windows XP (Korean version; SP2 I think, may be SP 3) using Novicorp WinToFlash enter link description here. It managed to boot up at first and I was able to format the C driveand get Windows install to start up. It took forever to copy all the files from the USB and after the first reboot, before installation started, I cancelled the reboot from windows install, went to BIOS and changed the boot device priority from USB to internal hard drive. But now on bootup it showed me a list with two options for booting windows XP (much like in the case of a multi OS system) so I assumed that I had formatted drive D by mistake and installed XP there, instead of on C drive. Anyway, I chose one of them and it continued my Windows installation. I got the blue installation screen that shows ads about Windows XP on the right frame and estimated remaining time on the left. However, after completing the process, after the first reboot, instead of showing the Windows XP logo, it says \system32\hall.dll is missing (or corrupted I'm not sure, I needed to install the Korean version of windows and I could not exactly read the error message, however it was one that I have already seen in an English version installation, and I am sure it says either missing or corrupted). The problem is, now it shows the same error again when I try to reboot it from the USB drive as well. I tried to boot a portable version of Linux I made in another USB, but the computer does not boot up from that USB, and it shows hal.dll error when I try to boot it using the WIN XP installation USB I made, as well as when I try to boot it from the hard drive, where I suppose Win XP is now semiinstalled. So now I can't get the computer to start up at all, except going to the BIOS. What else can I try to solve this? Also, would it be possible to install XP on this computer by connecting it to another one running Windows 7 ultimate, through the ethernet card? That is, network just the two computers together, then install windows XP on the notebook from the desktop running windows 7? Please help, I'm running out of ideas on this one. If Korean version of windows XP is the problem then I am willing to install English version as well. (but I need to make sure if that is the real cause of the problem)

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Hylafax / Capi4hylafax: faxgetty does not recognize number of lines

  - by Wrikken

  We've got a T.30 card, 30 working lines on it, but for some reason, if I add more then 30 faxes in the queue at any time (and we're busy enough at peak times that this happens a lot), faxgetty sends faxes to non-existent lines and they appear in the error queue as a 'busy' signal on the line, which results in a lot of failed faxes because the counter of max 3 tries increases rapidly. This is using faxgetty (USE_FAXGETTY="y" in /etc/default/hylafax). I've inherited this thing, so I'm not entirely sure how faxgetty is supposed to know the number of lines. However, if I alter the script to faxmodem (USE_FAXGETTY="n" in /etc/default/hylafax and manually enabling 30 modems), this behavior goes away (new faxes 'wait' for a line to be available before trying to send, so each try / fail is a valid one on a working line, majorly descreasing the amount of failed faxes. However, when researching this almost anyone talks about faxgetty being the preferred, more robust, method, and on top of that for some unexplained reason all FIFO's disappeared for some reason after several errorless hours with faxmodem, forcing a hylafax restart using faxgetty until we figured out why this faxmodem solution failed (which is another question, and somewhat out of scope here). Environment: Debian 2.6.26-2-amd64 capi4hylafax 1:01.03.00.99.svn.300-12 hylafax-client 2:4.4.4-10.1 hylafax-server 2:4.4.4-10.1 Config --hfaxd.conf-- LogFacility: daemon ServerTracing: 0x1ff --hyla.conf-- Host: localhost Verbose: No VRes: 196 TimeZone: local DialRules: "/etc/hylafax/dialrules.europe" --/etc/hylafax/config -- InternationalPrefix: 00 LongDistancePrefix: 0 AreaCode: 99999 CountryCode: 31 DialStringRules: "etc/dialrules.europe" ModemGroup: any:faxCAPI SendFaxCmd: "/usr/bin/wrapc2faxsend" --/etc/hylafax/config.faxCAPI -- SpoolDir: /var/spool/hylafax FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd PollRcvdCmd: /var/spool/hylafax/bin/pollrcvd FaxReceiveUser: uucp FaxReceiveGroup: dialout LogFile: /var/spool/hylafax/log/capi4hylafax #no, checking this log did not yield anything interesting LogTraceLevel: 4 LogFileMode: 0600 ModemGroup: any:faxCAPI #repeats of faxCAPI2 = faxCAPI30, with of course another devicename/local ident: { HylafaxDeviceName: faxCAPI RecvFileMode: 0600 FAXNumber: ****redacted**** LocalIdentifier: ****some-ident-per-device*** MaxConcurrentRecvs: 0 OutgoingController: 1 OutgoingMSN: SuppressMSN: 0 NumberPrefix: NumberPlusReplacer: "00" UseISDNFaxService: 0 RingingDuration: 0 { Controller: 1 AcceptSpeech: 0 UseDDI: 0 DDIOffset: DDILength: 0 IncomingDDIs: IncomingMSNs: AcceptGlobalCall: 1 } } So in short: How does faxgetty determine the number of lines available? (the man page isn't terribly revealing, and I can't find an appropriate setting in hylafax-config. And how can I get a capi4hylafax/hylafax setup which queues more faxes then lines are available correctly without immediately incrementing the fail count? We will not be receiving any faxes on this machine b.t.w. As I said, I've inherited this thing, so if there are important configuration options I'm not including, please let me know.

  Read the article

• Link aggregation with freebsd8 and a cicso 3550, what am i doing wrong?

  - by Flamewires

  Hey, I am trying to setup Link Aggrigation with LACP (well, anything that provides increased bandwidth and failover using my setup will work). I'm running FreeBSD 8.0 on 3 machines. M1 is running 2 10/100 ethernetcards setup for link aggrigation using lagg. for reference: ifconfig em0 up ifconfig tx0 up ifconfig create lagg0 ifconfig lagg0 laggproto lacp laggport tx0 laggport em0 192.168.1.16 netmask 255.255.255.0 I plugged them into ports 1 and 2 of a Cicso 3550. then ran: configure terminal interface range Fa0/1 - 2 switchport mode access switchport access vlan 1 channel-group 1 mode active (everythings in vlan 1) Now Im able to connect the other computers to other ports on the switch and failover works great, i can unplug cables in the middle of a transfer and the traffic gets rerouted. However, im not noticing any speed increase. My test setup: load balancing: i tried dst and src on the switch, neither seemed to give me a speed increase. I am SCPing 2 500 meg files from the lagg computer to other computers (one each) which are also running 10/100 full duplex cards. I get transfer speeds of about 11.2-11.4 Mbps to a single host, and about half that (5.9-6.2) Mbps when transferring to both at the same time. From what I understood with destination load balancing the router was suppose to balance traffic headed for 1 computer over 1 port and traffic headed for another over a diff(in this case) the other port. With destination-MAC address forwarding, when packets are forwarded to an EtherChannel, the packets are distributed across the ports in the channel based on the destination host MAC address of the incoming packet. Therefore, packets to the same destination are forwarded over the same port, and packets to a different destination are sent on a different port in the channel. For the 3550 series switch, when source-MAC address forwarding is used, load distribution based on the source and destination IP address is also enabled for routed IP traffic. All routed IP traffic chooses a port based on the source and destination IP address. Packets between two IP hosts always use the same port in the channel, and traffic between any other pair of hosts can use a different port in the channel. (Link) What am i doing wrong/what would i need to do to see a speed increase beyond what i could do with just a single card?

  Read the article

• Remove DRM from *.pdb e-book that I own - while maintaining footnotes, etc.?

  - by ziesemer

  Background: I've already reviewed Remove DRM from ePub Files? and How can I remove DRM from Kindle books? - the answers to which have already brought me partial process. The challenge is that I have a few purchased *.pdb e-books that I purchased in years past, e.g. 2006. In particular, they were purchased from the palm eBook Store (ebooks.palm.com - now defunct, possibly part of http://www.ereader.com / Barnes & Noble?) - originally for use on a Palm Treo that has since died. Of particular note is that I have a revision / publication of a book that is no longer published, and not available as an e-book from anywhere else that I've been able to find. (I feel fortunate to have even found the *.pdb files on backup.) I have a copy of the electronic invoice for it - which includes the details necessary for unlocking - the "Purchaser's Name" and the "Unlock Code" - which is the digits of my credit card # that I had used to purchase it. Given the above information, I was surprised to be able to open the book using the Windows eReader software and unlock it. Here I am able to view the complete contents and functionality of the book as I had done on the Palm Treo - including viewing of linked annotations / footnotes, etc. Following the full spirit of Remove DRM from ePub Files?, I want to ensure that I can access this on any device of my choosing - especially now and in the future, and as new technologies arrive and disappear. Ideally, I'm just looking to accomplish the minimum necessary to allow import into calibre. Outstanding Issue: I've found a few solutions that have given me "90%" success - all based on various versions of some Python scripts - including versions 0.21 and 0.11 of "erdr2pml.py" (based on "ereader2html"). Unfortunately, unless I'm missing something, these programs are attempting to also "convert" - instead of just "decrypting". As such, the outputs are missing embedded images and/or footnotes. I.E., there is a linked, underlined, and super-scripted "a" after some text - but the content of the footnote no longer exists. I can validate this by inspecting the generated *.pmlz file, and nowhere does it contain the original footnotes that are still visible in the original *.pdb file. I'm hoping to find a process that focuses on the decryption only, instead of attempting any type of a content conversion - or if a content conversion is required / involved, that it maintains all of the features and content of the original. (Again, I'm confident that if/once a version is obtained that calibre can import, I'll be able to fulfill the rest of my requirements.)

  Read the article

• Are FC and SAS DAS devices standard enough?

  - by user222182

  Before I ask my questions, here is some background info that may or may not be useful: For the first time I find myself needing a DAS solution. My priority is data through-put in a single direction. I can write large blocks, and I don't need to read at the same time. The server (the data producing device) is not really a typical server, its a very powerful single board computer. As such I have limited options when it comes to the add-in cards I can install since it must use the fairly uncommon interface, XMC. Currently I believe I am limited PCIex8 gen 1 which means that the likely bottle neck for me will be this 16gbps connection. XMC Boards I have found so far offer the following connections: a) Dual 10GBE ethernet controller, total throughput 20gbps b) Dual Quad SAS 2.0 Connectors (SFF-8XXX) HBA (no raid), total throughput 48 gbps c) Dual FC 8gb HBA (no raid), total throughput 16gbps My questions for you guys are: 1) Are SAS and/or FC, and by extension their HBAs, standard enough that I could purchase a Dell or Aberdeen storage server with a raid controller that has external SAS or FC ports and expect that I can connect it to my SAS or FC HBA, be presented with a single volume (if I so configured the storage server), all without having to check for HBA compatibility? 2) On a device like a Dell PowerVault (either DAS or NAS) is there an OS on it to concern myself with, or is it meant to be remotely managed? Is there a local interface in case I cant remotely manage it (i.e. if my single board computer uses an OS not supported by Dell OpenManage). Would this be true of nearly any device which calls itself a DAS? 3) If I purchase some sort of Supermicro storage chassis, installed a raid controller with external connections, is there a nice lightweight OS I can run just for management of the controller? Would I even need an OS since the raid card would be configured pre-boot anyway? 4) It is much easier to buy XMC based 10gigabit ethernet cards (generally dual port). In what ways would I be getting into trouble by using iSCSI as a DAS are direct cabling with SFP+ cables? Thanks in advance

  Read the article

• Blank displays after inactivity, mouse cursor not showing up

  - by Mike Christiansen

  I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

  Read the article

• Windows Setup could not configure Windows to run on this computer's hardware

  - by Hello71

  The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• Wake On Lan only works on first boot, not sequent ones

  - by sp3ctum

  I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Windows 8 ignores more specific route

  - by Lander

  OS: Windows 8 I have a cabled NIC (connected to router with ip 192.168.1.0) and a WIFI NIC (connected to a router with ip 192.168.1.1) . I want all traffic to go through the cabled NIC, except the 192.168.1.0/8 range should use the wifi-nic. This was working fine in Windows 7, without any manual configuration. In Windows 8 however, it's not. My routing table: =========================================================================== Interface List 14...f2 7b cb 13 e7 f0 ......Microsoft Wi-Fi Direct Virtual Adapter 13...b8 ac 6f 54 d2 5c ......Realtek PCIe FE Family Controller 12...f0 7b cb 13 e7 f0 ......Dell Wireless 1397 WLAN Mini-Card 1...........................Software Loopback Interface 1 15...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 16...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.198 30 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.233 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.233 276 192.168.0.233 255.255.255.255 On-link 192.168.0.233 276 192.168.0.255 255.255.255.255 On-link 192.168.0.233 276 192.168.1.0 255.255.255.0 192.168.1.1 192.168.1.198 31 192.168.1.198 255.255.255.255 On-link 192.168.1.198 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.0.233 276 224.0.0.0 240.0.0.0 On-link 192.168.1.198 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.0.233 276 255.255.255.255 255.255.255.255 On-link 192.168.1.198 286 =========================================================================== Persistent Routes: None I added the rule for 192.168.1.0. I would think Windows should use this rule for the IP 192.168.1.1 because it's more specific than the default-route. However it's not: C:\Windows\system32>tracert 192.168.1.1 Tracing route to 192.168.1.1 over a maximum of 30 hops 1 58 ms 4 ms 4 ms 192.168.0.1 2 68 ms 12 ms 11 ms ^C So... What do I do wrong? And how can I make Windows use the wireless NIC for 192.168.1.0/8

  Read the article

• server 2008 r2 - wbadmin systemstatebackup - system writer not found in the backup

  - by TWood

  I am trying to manually run a systemstatebackup command on my server 2008 r2 box and I am getting an error code '2155347997' when I view the backup event log details. The command line tells me that I have log files written to the c:\windows\logs\windowsserverbackup\ path but I have no files of the .log type there. My command window tells me "System Writer is not found in the backup". However when I run vssadmin list writers I find System Writer in the list and it shows normal status with no last errors stored. I am running this from an elevated command prompt as well as from a logged on administrator account. My backup target path has permission for network service to have full control and it has plenty of free space. Looking in eventlog I have two VSS error 8194 that happen immediately before the Backup error 517 which has the errorcode 2155347997 listed. All three of these errors are a result of trying to run the command for the systemstatebackup. It's my belief that some VSS related permission is failing and exiting the backup process before it ever gets started. Because of this the initial code that creates the log files must not be running and this is why I have no files. When running the systemstatebackup command from the command prompt and watching the windowsserverbackup directory I do see that I have a Wbadmin.0.etl file which gets created but it is deleted when the backup errors out and stops. I have looked online and there are numerous opinions as to the cause of this error. These are the things I have corrected to try and fix this issue before posting here: Machine runs a HP 1410i smart array controller but at one time also used a LSI scsi card. Used networkadminkb.com's kb# a467 to find one LSI_SCSI entry in HKLMSysCurrentControlSetServices which start was set to 0x0 and I modified to 0x3. No changes. In HKLMSystemCurrentControlSetServicesVSSDiag I gave network service full control where it previously only had "Special Permission". No changes. I followed KB2009272 to manually try to fix system writer. These are all of the things I have tried. What else should I look at to resolve this issue? It may be important to note that I run Mozy Pro on this server and that was known in the past to use VSS for copying operations and it occasionally threw an error. However since an update last year those error event log entries have stopped.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• FreeBSD jail with IPFW with loopback - unable to connect loopback interface

  - by khinester

  I am trying to configure a one IP jail with loopback interface, but I am unsure how to configure the IPFW rules to allow traffic to pass between the jail and the network card on the server. I have followed http://blog.burghardt.pl/2009/01/multiple-freebsd-jails-sharing-one-ip-address/ and https://forums.freebsd.org/viewtopic.php?&t=30063 but without success, here is what i have in my ipfw.rules # vim /usr/local/etc/ipfw.rules ext_if="igb0" jail_if="lo666" IP_PUB="192.168.0.2" IP_JAIL_WWW="10.6.6.6" NET_JAIL="10.6.6.0/24" IPF="ipfw -q add" ipfw -q -f flush #loopback $IPF 10 allow all from any to any via lo0 $IPF 20 deny all from any to 127.0.0.0/8 $IPF 30 deny all from 127.0.0.0/8 to any $IPF 40 deny tcp from any to any frag # statefull $IPF 50 check-state $IPF 60 allow tcp from any to any established $IPF 70 allow all from any to any out keep-state $IPF 80 allow icmp from any to any # open port ftp (20,21), ssh (22), mail (25) # ssh (22), , dns (53) etc $IPF 120 allow tcp from any to any 21 out $IPF 130 allow tcp from any to any 22 in $IPF 140 allow tcp from any to any 22 out $IPF 150 allow tcp from any to any 25 in $IPF 160 allow tcp from any to any 25 out $IPF 170 allow udp from any to any 53 in $IPF 175 allow tcp from any to any 53 in $IPF 180 allow udp from any to any 53 out $IPF 185 allow tcp from any to any 53 out # HTTP $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state # deny and log everything $IPF 500 deny log all from any to any # NAT $IPF 63000 divert natd ip from any to any via $jail_if out $IPF 63000 divert natd ip from any to any via $jail_if in but when i create a jail as: # ezjail-admin create -f continental -c zfs node 10.6.6.7 /usr/jails/node/. /usr/jails/node/./etc /usr/jails/node/./etc/resolv.conf /usr/jails/node/./etc/ezjail.flavour.continental /usr/jails/node/./etc/rc.d /usr/jails/node/./etc/rc.conf 4 blocks find: /usr/jails/node/pkg/: No such file or directory Warning: IP 10.6.6.7 not configured on a local interface. Warning: Some services already seem to be listening on all IP, (including 10.6.6.7) This may cause some confusion, here they are: root syslogd 1203 6 udp6 *:514 *:* root syslogd 1203 7 udp4 *:514 *:* i get these warning and then when i go into the jail environment, i am unable to install any ports. any advice much appreciated.

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• Possible capacitor plague - need help identifying

  - by cornjuliox

  I've been having some PC power issues lately, and I think I've tracked it down to a bad power supply. Lately, when I'm on my PC it will often restart without warning, displaying "Hypertransport sync flood error occurred last boot." once POST finishes. I've googled the error, but can't come to a definitive conclusion as to what's causing it. I've seen posts suggesting that it might be a power supply issue, but nothing conclusive. Here's what I've done so far: -I haven't installed anything suspect within the last 3 months. -I do overclock just a tiny bit, so I tried raising the voltages a little. That didn't work so I brought both CPU multiplier and voltages all back to their default settings, but that didn't solve the problem either. The problem still occurs. -AV scanned the whole system, nothing suspect. -I suspected that it might be a bad power supply so I cracked that open and found the following: I think it might be cap plague, but I'm not sure. It looks more like glue TBH. Could someone help me figure out what might be wrong with this PC? EDIT: Sometimes, after these restarts, I noticed that the GPU fan doesn't spin up, and the single rear case fan that just happens to be connected to the same molex Y-cable as the GFX card doesn't spin up either. Anything to that? EDIT 2: I do use the system quite heavily, but I don't know how that will factor into this. I often play Diablo 3 and EVE Online at the same time, frequently alt-tabbing between the two. I also have Firefox open in the background, sometimes with several tabs, and if I feel like it, I'll mute the in-game sound and open foobar2000 for better music. Could it be that I'm just pushing this thing too hard? EDIT 3: I also noticed something odd. Right before I experience these restarts, my monitor would suffer from very faint lines of static moving across the screen. The monitor is still very much useable, but it is very annoying. Following the restart it disappears, and then would gradually re-appear over the next few days, and then restarts again. I find it to be very odd. System specs for good measure: Orion 600 W PSU AMD Athlon II X3 440 (overclocked to 3.14 ghZ, raised the CPU multiplier to x13 from x10) MSI G40-775 motherboard 1 GB inno3D GTX 550 ti 4 GB DDR3 RAM 500 GB Samsung SATA HD

  Read the article

• Local admin password recovery: Windows Vista

  - by Jim Dennis

  I am faced with an unsettling situation. A friend of my father's has rather suddenly become a widower. Naturally they've taken care of the bank accounts and all the normal mundane things that people have been doing for a century or so. However, she was the computer user of the household. He was aware that they had some online banking stuff and bill paying stuff ... and that she spent lots of time on FaceBook and stuff like that. However, he doesn't know what her local passwords were (actually only vaguely aware that her couple of desktop and couple of laptop system even had passwords). He's never heard of "admin" passwords so that's no good either. In the past I've used KNOPPIX and the old LinuxCare "bootable business card" to recover NT passwords. I've never done this with MS Windows Vista. So, I'm looking for the best advice on how to do this. Naturally I do have physical access to the systems (the two laptops are charging across the room from me; and her old desktop systems are, naturally, still back at his place). Getting it right is much more important than fast or easy (I don't want to mess up those filesystems and possibly lose some photos or other stuff that he or his kids or grandkids will want). (BTW: if anyone things this is some social engineering hack to play upon the sympathies of the community to get the information I'm asking for ... think about it for a minute. I know about IRC and the "warez" boards. I know I can find this stuff out there if I dig enough. I'm just asking here because it'll hopefully be faster and, secondarily to raise awareness. As more of us put more of our lives online ... as we get older and as places like FaceBook continue to widen the appeal of computing to a broader segment of older people ... we are, as computer nerds, going to see a lot more of this. Survivors will needs us to be careful, sensitive and ethically responsible as they try to recover those bits of legacy during their bereavement. I can now tell you, first hand, it sucks!)

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Can't save screen resolution setting.

  - by Searock

  Hi, My screen resolution in windows and previous version of Ubuntu (9.04) was 1152 x 864. But in Ubuntu 10.04 it gives me an option of 1024 x 786 and 1360 x 786. I have some how managed to add 1152x684 resolution by using xrandr command. searock@searock-desktop:~$ cvt 1152 864 1152x864 59.96 Hz (CVT 1.00M3) hsync: 53.78 kHz; pclk: 81.75 MHz Modeline "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --addmode S-video 1152x864 xrandr: cannot find output "S-video" searock@searock-desktop:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1360x768 59.8 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 59.9 1152x864_60.00 (0x124) 81.0MHz h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.3KHz v: height 864 start 867 end 871 total 897 clock 59.4Hz searock@searock-desktop:~$ xrandr --addmode VGA1 1152x864_60.00 But the problem is when ever I restart my computer I get this message. Could not apply the stored configuration for the monitors. Could not find a suitable configuration of screens. And then it comes back to 1024 x 786 My graphic card details : Intel(R) 82945G Express Chipset Family. Is there any way I can fix this once for all ? Thanks. Edit 1 : rumtscho has suggested me to modify xorg.conf file. But I am not sure what HorizSync means? is it Horizontal frequency ? My monitor model is Acer v173. Here's my specification. So what should be HorizSync and VertRefresh ? Edit 2 : I have edited my Xorg.conf file as follows : Section "Monitor" Identifier "Configured Monitor" HorizSync 30-80 VertRefresh 55-75 EndSection then I added the resolution and restarted my computer and still I am facing the same problem. Is there something that I am missing? Edit 3 : For now I have edited /etc/gdm/Init/Default(gdm startup scripts) to include following xrandr commands, just below line initctl -q emit login-session-start DISPLAY_MANAGER=gdm xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00<br/> xrandr -s 1152x864_60.00 This has solved my problem, but this commands have increased my computer's boot time. I think I will have to edit xorg file properly. Edit 4 : Instead of adding this files to gdm startup scripts I have created a shell script and added it to startup (System - Preference - Startup Applications) #!/bin/bash xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00 xrandr -s 1152x864_60.00 And don't forget to add execution rights. (Right Click - Properties - Permission - Allow executing file as program)

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >