Search Results

Search found 16940 results on 678 pages for 'disk drive'.

Page 263/678 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

• How can I limit the cache used by copying so there is still memory available for other cache?

  - by Peter

  Basic situation: I am copying some NTFS disks in openSuSE. Each one is 2TB. When I do this, the system runs slow. My guesses: I believe it is likely due to caching. Linux decides to discard useful cache (eg. kde4 bloat, virtual machine disks, LibreOffice binaries, Thunderbird binaries, etc.) and instead fill all available memory (24 GB total) with stuff from the copying disks, which will be read only once, then written and never used again. So then any time I use these apps (or kde4), the disk needs to be read again, and reading the bloat off the disk again makes things freeze/hiccup. Due to the cache being gone and the fact that these bloated applications need lots of cache, this makes the system horribly slow. Since it is USB,the disk and disk controller are not the bottleneck, so using ionice does not make it faster. I believe it is the cache rather than just the motherboard going too slow, because if I stop everything copying, it still runs choppy for a while until it recaches everything. And if I restart the copying, it takes a minute before it is choppy again. But also, I can limit it to around 40 MB/s, and it runs faster again (not because it has the right things cached, but because the motherboard busses have lots of extra bandwidth for the system disks). I can fully accept a performance loss from my motherboard's IO capability being completely consumed (which is 100% used, meaning 0% wasted power which makes me happy), but I can't accept that this caching mechanism performs so terribly in this specific use case. # free total used free shared buffers cached Mem: 24731556 24531876 199680 0 8834056 12998916 -/+ buffers/cache: 2698904 22032652 Swap: 4194300 24764 4169536 I also tried the same thing on Ubuntu, which causes a total system hang instead. ;) And to clarify, I am not asking how to leave memory free for the "system", but for "cache". I know that cache memory is automatically given back to the system when needed, but my problem is that it is not reserved for caching of specific things. Question: Is there some way to tell these copy operations to limit memory usage so some important things remain cached, and therefore any slowdowns are a result of normal disk usage and not rereading the same commonly used files? For example, is there a setting of max memory per process/user/file system allowed to be used as cache/buffers?

  Read the article

• Log4j: Issues about the FallbackErrorHandler

  - by rdogpink

  I am working on a client-server-application and wanted to implement a flexible Loggingframework, so I chose log4j, which doesn´t really evolve anymore, but it is still handy framework. Because the Logging happens along the network, i wanted a solution for the case, that the network drive isn´t available, so the Logger has to change its destination file(s). Now I wanted to use the FallbackErrorHandler (configured with a XML-File) from the Log4j-library and the implementation worked: When my network drive isn´t available, it switches to a local Logfile, so no logging should be lost. But I headded two problems since yesterday and couldn´t figure or find out, how to solve it. No return to initial Logging Configuration: When the network drive is on again and the Logger could write to the old destinations, log4j still logs at the local drive and I can´t figure out, how to notify the original (primary) Logger to start again. I also tried to attach a second Appender to the ErrorHandler, which should mirror the failed primary Logger, that it tries to write on the network destination and when the network is on again, it logs in both files, on the local and on the network drive. But unfortunately it didn´t work out, I only got a failure message that the ErrorHandler-content doesn´t fit. log4j:WARN The content of element type "errorHandler" must match "(param*,root-ref?,logger-ref*,appender-ref?)". This is the responsible code. <appender name="TraceAppender" class="org.apache.log4j.DailyRollingFileAppender"> <!-- The second appender-ref "TestAppender" leads to the error. --> <errorHandler class="org.apache.log4j.varia.FallbackErrorHandler"> <logger-ref ref="com.idoh"/> <appender-ref ref="TraceFallbackAppender"/> <appender-ref ref="TestAppender"/> </errorHandler> <param name="datePattern" value=".yyyy-MM-dd" /> <param name="file" value="logs/Trace.txt" /> <layout class="org.apache.log4j.PatternLayout"> <param name="ConversionPattern" value="%-6r %d{HH:mm:ss,SSS} [%t] %-5p - %m%n"/> </layout> </appender> So, how could I trigger log4j to reset to initial configuration or hold a second appender parallel to the "Local-Logger". My Application should work by itself and shouldn´t have to be restarted often. First Error message is swallowed: I recognized, that the first message, which leads to the switching between the primary logger and the FallbackErrorHandler (for example a logging-request to a readonly-File), is swallowed, so neither the primary logger logs it (because it can´t) nor the backup-Logger knows what it missed. So anybody else ran in this problem and could solve it? Or has any suggestions?

  Read the article

• "domain crashed" when creating new Xen instance

  - by user47650

  I have downloaded a Xen virtual machine image from the appscale project, and I am trying to start it up. However once I run the command; xm create -c -f xen.conf The instance immediately crashes and provides no console output. however it produces logs that I have posted below. but this is the error; [2011-03-01 12:34:03 xend.XendDomainInfo 3580] WARNING (XendDomainInfo:1178) Domain has crashed: name=appscale-1.4b id=10. I have managed to mount the root.img file locally and verify that it is actually an ext3 file system. I am running Xen 3.0.3 that is a stock RPM from the CentOS 5 repos; # rpm -qa | grep -i xen xen-libs-3.0.3-105.el5_5.5 xen-3.0.3-105.el5_5.5 xen-libs-3.0.3-105.el5_5.5 kernel-xen-2.6.18-194.32.1.el5 any suggestions on how to proceed with troubleshooting? (i am a newbie to Xen) so far I have enabled console logging, but the log file is empty. ==> domain-builder-ng.log <== xc_dom_allocate: cmdline=" ip=:1.2.3.4::::eth0:dhcp root=/dev/sda1 ro xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console", features="" xc_dom_kernel_file: filename="/boot/vmlinuz-2.6.27-7-server" xc_dom_malloc_filemap : 2284 kB xc_dom_ramdisk_file: filename="/boot/initrd.img-2.6.27-7-server" xc_dom_malloc_filemap : 9005 kB xc_dom_boot_xen_init: ver 3.1, caps xen-3.0-x86_64 xen-3.0-x86_32p xc_dom_parse_image: called xc_dom_find_loader: trying ELF-generic loader ... failed xc_dom_find_loader: trying Linux bzImage loader ... xc_dom_malloc : 9875 kB xc_dom_do_gunzip: unzip ok, 0x234bb2 -> 0x9a4de0 OK elf_parse_binary: phdr: paddr=0x200000 memsz=0x447000 elf_parse_binary: phdr: paddr=0x647000 memsz=0xab888 elf_parse_binary: phdr: paddr=0x6f3000 memsz=0x908 elf_parse_binary: phdr: paddr=0x6f4000 memsz=0x1c2f9c elf_parse_binary: memory: 0x200000 -> 0x8b6f9c elf_xen_parse_note: GUEST_OS = "linux" elf_xen_parse_note: GUEST_VERSION = "2.6" elf_xen_parse_note: XEN_VERSION = "xen-3.0" elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 elf_xen_parse_note: ENTRY = 0xffffffff8071e200 elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80209000 elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" elf_xen_parse_note: PAE_MODE = "yes" elf_xen_parse_note: LOADER = "generic" elf_xen_parse_note: unknown xen elf note (0xd) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 elf_xen_parse_note: PADDR_OFFSET = 0x0 elf_xen_addr_calc_check: addresses: virt_base = 0xffffffff80000000 elf_paddr_offset = 0x0 virt_offset = 0xffffffff80000000 virt_kstart = 0xffffffff80200000 virt_kend = 0xffffffff808b6f9c virt_entry = 0xffffffff8071e200 xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff80200000 -> 0xffffffff808b6f9c xc_dom_mem_init: mem 1024 MB, pages 0x40000 pages, 4k each xc_dom_mem_init: 0x40000 pages xc_dom_boot_mem_init: called x86_compat: guest xen-3.0-x86_64, address size 64 xc_dom_malloc : 2048 kB ==> xend.log <== [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2114) UUID Created: True [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2115) Devices to release: [], domid = 9 [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2127) Releasing PVFB backend devices ... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:207) XendDomainInfo.create(['domain', ['domid', 9], ['uuid', 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0'], ['vcpus', 1], ['vcpu_avail', 1], ['cpu_cap', 0], ['cpu_weight', 256], ['memory', 1024], ['shadow_memory', 0], ['maxmem', 1024], ['features', ''], ['name', 'appscale-1.4b'], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['image', ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']]], ['cpus', []], ['device', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]], ['device', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']]], ['state', '----c-'], ['shutdown_reason', 'crash'], ['cpu_time', 0.000339131], ['online_vcpus', 1], ['up_time', '0.952092885971'], ['start_time', '1299011639.92'], ['store_mfn', 1169289], ['console_mfn', 1169288]]) [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:329) parseConfig: config is ['domain', ['domid', 9], ['uuid', 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0'], ['vcpus', 1], ['vcpu_avail', 1], ['cpu_cap', 0], ['cpu_weight', 256], ['memory', 1024], ['shadow_memory', 0], ['maxmem', 1024], ['features', ''], ['name', 'appscale-1.4b'], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['image', ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']]], ['cpus', []], ['device', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]], ['device', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']]], ['state', '----c-'], ['shutdown_reason', 'crash'], ['cpu_time', 0.000339131], ['online_vcpus', 1], ['up_time', '0.952092885971'], ['start_time', '1299011639.92'], ['store_mfn', 1169289], ['console_mfn', 1169288]] [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:446) parseConfig: result is {'features': '', 'image': ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']], 'cpus': [], 'vcpu_avail': 1, 'backend': [], 'uuid': 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'on_reboot': 'restart', 'cpu_weight': 256.0, 'memory': 1024, 'cpu_cap': 0, 'localtime': None, 'timer_mode': None, 'start_time': 1299011639.9200001, 'on_poweroff': 'destroy', 'on_crash': 'restart', 'device': [('vif', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]), ('vbd', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']])], 'bootloader': None, 'maxmem': 1024, 'shadow_memory': 0, 'name': 'appscale-1.4b', 'bootloader_args': None, 'vcpus': 1, 'cpu': None} [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1784) XendDomainInfo.construct: None [2011-03-01 12:34:02 xend 3580] DEBUG (balloon:145) Balloon: 3034420 KiB free; need 4096; done. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1953) XendDomainInfo.initDomain: 10 256.0 [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1994) _initDomain:shadow_memory=0x0, maxmem=0x400, memory=0x400. [2011-03-01 12:34:02 xend 3580] DEBUG (balloon:145) Balloon: 3034412 KiB free; need 1048576; done. [2011-03-01 12:34:02 xend 3580] INFO (image:139) buildDomain os=linux dom=10 vcpus=1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:208) domid = 10 [2011-03-01 12:34:02 xend 3580] DEBUG (image:209) memsize = 1024 [2011-03-01 12:34:02 xend 3580] DEBUG (image:210) image = /boot/vmlinuz-2.6.27-7-server [2011-03-01 12:34:02 xend 3580] DEBUG (image:211) store_evtchn = 1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:212) console_evtchn = 2 [2011-03-01 12:34:02 xend 3580] DEBUG (image:213) cmdline = ip=:1.2.3.4::::eth0:dhcp root=/dev/sda1 ro xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console [2011-03-01 12:34:02 xend 3580] DEBUG (image:214) ramdisk = /boot/initrd.img-2.6.27-7-server [2011-03-01 12:34:02 xend 3580] DEBUG (image:215) vcpus = 1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:216) features = ==> domain-builder-ng.log <== xc_dom_build_image: called xc_dom_alloc_segment: kernel : 0xffffffff80200000 -> 0xffffffff808b7000 (pfn 0x200 + 0x6b7 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x200+0x6b7 at 0x2aaaab5f6000 elf_load_binary: phdr 0 at 0x0x2aaaab5f6000 -> 0x0x2aaaaba3d000 elf_load_binary: phdr 1 at 0x0x2aaaaba3d000 -> 0x0x2aaaabae8888 elf_load_binary: phdr 2 at 0x0x2aaaabae9000 -> 0x0x2aaaabae9908 elf_load_binary: phdr 3 at 0x0x2aaaabaea000 -> 0x0x2aaaabb9a004 xc_dom_alloc_segment: ramdisk : 0xffffffff808b7000 -> 0xffffffff82382000 (pfn 0x8b7 + 0x1acb pages) xc_dom_malloc : 160 kB xc_dom_pfn_to_ptr: domU mapping: pfn 0x8b7+0x1acb at 0x2aaab0000000 xc_dom_do_gunzip: unzip ok, 0x8cb5e7 -> 0x1aca210 xc_dom_alloc_segment: phys2mach : 0xffffffff82382000 -> 0xffffffff82582000 (pfn 0x2382 + 0x200 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x2382+0x200 at 0x2aaab1acb000 xc_dom_alloc_page : start info : 0xffffffff82582000 (pfn 0x2582) xc_dom_alloc_page : xenstore : 0xffffffff82583000 (pfn 0x2583) xc_dom_alloc_page : console : 0xffffffff82584000 (pfn 0x2584) nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) xc_dom_alloc_segment: page tables : 0xffffffff82585000 -> 0xffffffff8259c000 (pfn 0x2585 + 0x17 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x2585+0x17 at 0x2aaab1ccb000 xc_dom_alloc_page : boot stack : 0xffffffff8259c000 (pfn 0x259c) xc_dom_build_image : virt_alloc_end : 0xffffffff8259d000 xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 xc_dom_boot_image: called arch_setup_bootearly: doing nothing xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches xc_dom_compat_check: supported guest type: xen-3.0-x86_32p xc_dom_update_guest_p2m: dst 64bit, pages 0x40000 clear_page: pfn 0x2584, mfn 0x11d788 clear_page: pfn 0x2583, mfn 0x11d789 xc_dom_pfn_to_ptr: domU mapping: pfn 0x2582+0x1 at 0x2aaab1ce2000 start_info_x86_64: called setup_hypercall_page: vaddr=0xffffffff80209000 pfn=0x209 domain builder memory footprint allocated malloc : 12139 kB anon mmap : 0 bytes mapped file mmap : 11289 kB domU mmap : 35 MB arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xd6fe1 shared_info_x86_64: called vcpu_x86_64: called vcpu_x86_64: cr3: pfn 0x2585 mfn 0x11d787 launch_vm: called, ctxt=0x97b21f8 xc_dom_release: called ==> xend.log <== [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:114) DevController: writing {'mac': '00:16:3B:72:10:E4', 'handle': '0', 'protocol': 'x86_64-abi', 'backend-id': '0', 'state': '1', 'backend': '/local/domain/0/backend/vif/10/0'} to /local/domain/10/device/vif/0. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:116) DevController: writing {'domain': 'appscale-1.4b', 'handle': '0', 'script': '/etc/xen/scripts/vif-bridge', 'state': '1', 'frontend': '/local/domain/10/device/vif/0', 'mac': '00:16:3B:72:10:E4', 'online': '1', 'frontend-id': '10'} to /local/domain/0/backend/vif/10/0. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:634) Checking for duplicate for uname: /local/xen/domains/appscale1.4/root.img [file:/local/xen/domains/appscale1.4/root.img], dev: sda1:disk, mode: w [2011-03-01 12:34:02 xend 3580] DEBUG (blkif:27) exception looking up device number for sda1:disk: [Errno 2] No such file or directory: '/dev/sda1:disk' [2011-03-01 12:34:02 xend 3580] DEBUG (blkif:27) exception looking up device number for sda1: [Errno 2] No such file or directory: '/dev/sda1' [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:114) DevController: writing {'virtual-device': '2049', 'device-type': 'disk', 'protocol': 'x86_64-abi', 'backend-id': '0', 'state': '1', 'backend': '/local/domain/0/backend/vbd/10/2049'} to /local/domain/10/device/vbd/2049. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:116) DevController: writing {'domain': 'appscale-1.4b', 'frontend': '/local/domain/10/device/vbd/2049', 'format': 'raw', 'dev': 'sda1', 'state': '1', 'params': '/local/xen/domains/appscale1.4/root.img', 'mode': 'w', 'online': '1', 'frontend-id': '10', 'type': 'file'} to /local/domain/0/backend/vbd/10/2049. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:993) Storing VM details: {'shadow_memory': '0', 'uuid': 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'on_reboot': 'restart', 'start_time': '1299011642.74', 'on_poweroff': 'destroy', 'name': 'appscale-1.4b', 'xend/restart_count': '0', 'vcpus': '1', 'vcpu_avail': '1', 'memory': '1024', 'on_crash': 'restart', 'image': "(linux (kernel /boot/vmlinuz-2.6.27-7-server) (ramdisk /boot/initrd.img-2.6.27-7-server) (ip :1.2.3.4::::eth0:dhcp) (root '/dev/sda1 ro') (args 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console'))", 'maxmem': '1024'} [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1028) Storing domain details: {'console/ring-ref': '1169288', 'console/port': '2', 'name': 'appscale-1.4b', 'console/limit': '1048576', 'vm': '/vm/d5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'domid': '10', 'cpu/0/availability': 'online', 'memory/target': '1048576', 'store/ring-ref': '1169289', 'store/port': '1'} [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:158) Waiting for devices vif. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:164) Waiting for 0. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1250) XendDomainInfo.handleShutdownWatch [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vif/10/0/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vif/10/0/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:523) hotplugStatusCallback 1. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices usb. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vbd. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:164) Waiting for 2049. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vbd/10/2049/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vbd/10/2049/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:523) hotplugStatusCallback 1. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices irq. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vkbd. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vfb. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices pci. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices ioports. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices tap. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vtpm. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] WARNING (XendDomainInfo:1178) Domain has crashed: name=appscale-1.4b id=10. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] ERROR (XendDomainInfo:2654) VM appscale-1.4b restarting too fast (2.275545 seconds since the last restart). Refusing to restart to avoid loops. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2189) XendDomainInfo.destroy: domid=10 ==> xen-hotplug.log <== Nothing to flush. ==> xend.log <== [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2114) UUID Created: True [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2115) Devices to release: [], domid = 10 [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2127) Releasing PVFB backend devices ... And this is the xen.conf file that I am using; # cat xen.conf # Configuration file for the Xen instance AppScale, created # bn VMBuilder kernel = '/boot/vmlinuz-2.6.27-7-server' ramdisk = '/boot/initrd.img-2.6.27-7-server' memory = 1024 vcpus = 1 root = '/dev/sda1 ro' disk = [ 'file:/local/xen/domains/appscale1.4/root.img,sda1,w', ] name = 'appscale-1.4b' dhcp = 'dhcp' vif = [ 'mac=00:16:3B:72:10:E4' ] on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' extra = 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console'

  Read the article

• Useful Command-line Commands on Windows

  - by Sung Meister

  The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

  Read the article

• Ubuntu 12.04 KVM running Ubuntu 12.04 with linux-image-virtual crash on boot

  - by D.Mill

  One of my VMs is stuck on "pause" in virsh. If I destroy and restart it, it will go to pause after a bit of time as "running". I can at best enter my username at login if I'm quick but it'll then shutdown. I don't know where to start with this so any help would be great!! I can access the VMs files via guestfish. the kern.log and syslog don't populate new lines. This is the last input I get from kern.log: Dec 13 11:21:08 soft201 kernel: imklog 5.8.6, log source = /proc/kmsg started. Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpuset Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpu Dec 13 11:21:08 soft201 kernel: [ 0.000000] Linux version 3.2.0-34-virtual (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #53-Ubuntu SMP Thu Nov 15 11:08:40 UTC 2012 (Ubuntu 3.2.0-34.53-virtual 3.2.33) Dec 13 11:21:08 soft201 kernel: [ 0.000000] Command line: root=UUID=61d48b48-a06a-48fb-842e-b38014086a93 ro quiet splash Dec 13 11:21:08 soft201 kernel: [ 0.000000] KERNEL supported cpus: Dec 13 11:21:08 soft201 kernel: [ 0.000000] Intel GenuineIntel Dec 13 11:21:08 soft201 kernel: [ 0.000000] AMD AuthenticAMD Dec 13 11:21:08 soft201 kernel: [ 0.000000] Centaur CentaurHauls Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-provided physical RAM map: Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfffc000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000dfffc000 - 00000000e0000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000feffc000 - 00000000ff000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000a20000000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] NX (Execute Disable) protection: active Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI 2.4 present. Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2007 Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) Dec 13 As you can see the last line gets cut off. I don't even know if this is that relevant. dmesg logs are empty. The qemu log for the VM returns this: 2012-12-13 12:29:47.584+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 40960 -smp 14,sockets=14,cores=1,threads=1 -name numerink201 -uuid f4a889ed-a089-05d0-cc9d-9825ab1faeba -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/numerink201.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/client.soft.fr/tmpcZAD9U.qcow2,if=none,id=drive-ide0-0-0,format=qcow2 -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -fsdev local,security_model=none,id=fsdev-fs0,path=/home/shared_folders/soft201 -device virtio-9p-pci,id=fs0,fsdev=fsdev-fs0,mount_tag=hostshare,bus=pci.0,addr=0x5 -netdev tap,fd=18,id=hostnet0 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=02:00:00:1d:b9:e7,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:0 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/3 qemu: terminating on signal 15 from pid 28248 2012-12-13 12:30:14.455+0000: shutting down I've added more logging, libvirt.log gives me this: 2012-12-13 13:24:38.525+0000: 27694: info : libvirt version: 0.9.8 2012-12-13 13:24:38.525+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:38.525+0000: 27694: warning : qemuCapsInit:856 : Failed to get host power management capabilities 2012-12-13 13:24:39.865+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.865+0000: 27694: warning : lxcCapsInit:77 : Failed to get host power management capabilities 2012-12-13 13:24:39.866+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.866+0000: 27694: warning : umlCapsInit:87 : Failed to get host power management capabilities I don't really know where to go from here. I'll post whatever info you require

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• My computer freezes irregurarly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• File Server - Storage configuration: RAID vs LVM vs ZFS something else... ?

  - by privatehuff

  We are a small company that does video editing, among other things, and need a place to keep backup copies of large media files and make it easy to share them. I've got a box set up with Ubuntu Server and 4 x 500 GB drives. They're currently set up with Samba as four shared folders that Mac/Windows workstations can see fine, but I want a better solution. There are two major reasons for this: 500 GB is not really big enough (some projects are larger) It is cumbersome to manage the current setup, because individual hard drives have different amounts of free space and duplicated data (for backup). It is confusing now and that will only get worse once there are multiple servers. ("the project is on sever2 in share4" etc) So, I need a way to combine hard drives in such a way as to avoid complete data loss with the failure of a single drive, and so users see only a single share on each server. I've done linux software RAID5 and had a bad experience with it, but would try it again. LVM looks ok but it seems like no one uses it. ZFS seems interesting but it is relatively "new". What is the most efficient and least risky way to to combine the hdd's that is convenient for my users? Edit: The Goal here is basically to create servers that contain an arbitrary number of hard drives but limit complexity from an end-user perspective. (i.e. they see one "folder" per server) Backing up data is not an issue here, but how each solution responds to hardware failure is a serious concern. That is why I lump RAID, LVM, ZFS, and who-knows-what together. My prior experience with RAID5 was also on an Ubuntu Server box and there was a tricky and unlikely set of circumstances that led to complete data loss. I could avoid that again but was left with a feeling that I was adding an unnecessary additional point of failure to the system. I haven't used RAID10 but we are on commodity hardware and the most data drives per box is pretty much fixed at 6. We've got a lot of 500 GB drives and 1.5 TB is pretty small. (Still an option for at least one server, however) I have no experience with LVM and have read conflicting reports on how it handles drive failure. If a (non-striped) LVM setup could handle a single drive failing and only loose whichever files had a portion stored on that drive (and stored most files on a single drive only) we could even live with that. But as long as I have to learn something totally new, I may as well go all the way to ZFS. Unlike LVM, though, I would also have to change my operating system (?) so that increases the distance between where I am and where I want to be. I used a version of solaris at uni and wouldn't mind it terribly, though. On the other end on the IT spectrum, I think I may also explore FreeNAS and/or Openfiler, but that doesn't really solve the how-to-combine-drives issue.

  Read the article

• What *exactly* gets screwed when I kill -9 or pull the power?

  - by Mike

  Set-Up I've been a programmer for quite some time now but I'm still a bit fuzzy on deep, internal stuff. Now. I am well aware that it's not a good idea to either: kill -9 a process (bad) spontaneously pull the power plug on a running computer or server (worse) However, sometimes you just plain have to. Sometimes a process just won't respond no matter what you do, and sometimes a computer just won't respond, no matter what you do. Let's assume a system running Apache 2, MySQL 5, PHP 5, and Python 2.6.5 through mod_wsgi. Note: I'm most interested about Mac OS X here, but an answer that pertains to any UNIX system would help me out. My Concern Each time I have to do either one of these, especially the second, I'm very worried for a period of time that something has been broken. Some file somewhere could be corrupt -- who knows which file? There are over 1,000,000 files on the computer. I'm often using OS X, so I'll run a "Verify Disk" operation through the Disk Utility. It will report no problems, but I'm still concerned about this. What if some configuration file somewhere got screwed up. Or even worse, what if a binary file somewhere is corrupt. Or a script file somewhere is corrupt now. What if some hardware is damaged? What if I don't find out about it until next month, in a critical scenario, when the corruption or damage causes a catastrophe? Or, what if valuable data is already lost? My Hope My hope is that these concerns and worries are unfounded. After all, after doing this many times before, nothing truly bad has happened yet. The worst is I've had to repair some MySQL tables, but I don't seem to have lost any data. But, if my worries are not unfounded, and real damage could happen in either situation 1 or 2, then my hope is that there is a way to detect it and prevent against it. My Question(s) Could this be because modern operating systems are designed to ensure that nothing is lost in these scenarios? Could this be because modern software is designed to ensure that nothing lost? What about modern hardware design? What measures are in place when you pull the power plug? My question is, for both of these scenarios, what exactly can go wrong, and what steps should be taken to fix it? I'm under the impression that one thing that can go wrong is some programs might not have flushed their data to the disk, so any highly recent data that was supposed to be written to the disk (say, a few seconds before the power pull) might be lost. But what about beyond that? And can this very issue of 5-second data loss screw up a system? What about corruption of random files hiding somewhere in the huge forest of files on my hard drives? What about hardware damage? What Would Help Me Most Detailed descriptions about what goes on internally when you either kill -9 a process or pull the power on the whole system. (it seems instant, but can someone slow it down for me?) Explanations of all things that could go wrong in these scenarios, along with (rough of course) probabilities (i.e., this is very unlikely, but this is likely)... Descriptions of measures in place in modern hardware, operating systems, and software, to prevent damage or corruption when these scenarios occur. (to comfort me) Instructions for what to do after a kill -9 or a power pull, beyond "verifying the disk", in order to truly make sure nothing is corrupt or damaged somewhere on the drive. Measures that can be taken to fortify a computer setup so that if something has to be killed or the power has to be pulled, any potential damage is mitigated. Thanks so much!

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• Converting an Oracle VM VirtualBox VM into an Oracle VM Server image

  - by wim.coekaerts

  As we are working on tighter seemless moving of VM's between the 2 products, here are a few simple steps to convert an existing Oracle VM VirtualBox image over. Steps involved to make it easy/straightforward : (1) When creating a VM in Virtualbox, using Oracle Linux as an example, make sure that /etc/fstab only uses labels. Do not use hardcoded device names. instead of an entry /dev/sda1 /u01 ext3 defaults 1 1 use LABEL=foo /u01 ext3 defaults 1 1 for more info on labels : man e2label or use a logical volume /dev/VolGroup00/LVfoo /u01 ext3 defaults 1 1 Doing so will make it easier to have an OS boot up on a different hypervisor with potentially different device names. For instance, the VirtualBox VM might expose a scsi driver while in Oracle VM Server you might end up with an ide disk, this then changes /dev/sda to /dev/hda. (2) If you have a VM created that you want to convert, then shut down the VM in VirtualBox and convert the image files : go the the directory that contains your HardDisk image files (.VirtualBox/HardDisks/* as an example) for each of the virtual disks run the following command : VBoxManage clonehd virtualdiskfilename.vdi system.img --format raw where virtualdiskfilename.vdi is the original VBox VM file (this can also be a vmdk file) and system.img is the name of the virtualdisk for Oracle VM. this can be any filename as well, I typically use system.img to specify the boot disk (as is common for Oracle VM template creation) (3) create a vm.cfg To run a VM converted from VirtualBox, you have to create a vm.cfg for Oracle VM server that creates an HVM guest. The easiest is to use a simple hvm vm.cfg and change it for your vm. I have an example here : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' disk = ['file:system.img,hda,w', 'file:oracle.img,hdb,w',',hdc:cdrom,r',] kernel = '/usr/lib/xen/boot/hvmloader' memory = '1024' name = 'vmname' on_crash = 'restart' on_reboot = 'restart' pae = 1 serial = 'pty' timer_mode = '0' usbdevice = 'tablet' vcpus = 1 vif = ['bridge=xenbr0,type=ioemu'] vif_other_config = [] vnc = 1 vncconsole = 1 vnclisten = '0.0.0.0' vncpasswd = '' vncunused = 1 If you take the above vm.cfg, all you need to do - modify disk = (add your virtual disks in there) - modify memory = (amount of memory your VM needs) - modify name = (enter a name for your VM here) - modify vif = (might want to replace bridge=xenbr0 to the bridge you want to use) if you want more than 1 vcpu or other changes of course you have to make those as well. (4) copy this set of files onto your Oracle VM server or onto a webserver in a subdirectory and import the template through Oracle VM Manager. You can also just start the vm using xm create vm.cfg if you like. And that's it. As I said, we are working on automation around all this but it is relatively trivial to convert VM's over as long as you take the basic issues into account. Primarily the set up of the filesystems and the use of labels in /etc/fstab. There are other potential things to look at, such as network config. If you want to make that part clean then prior to shutting down the VM change /etc/modprobe.conf and/or add the mac address of the VM into the vm.cfg in the vifs line. The good thing, at least with Linux, is that even tho the virtual hardware changes, Linux will deal with it just fine (e1000 vs 8139 realtek, ide vs scsi etc). hope this helps.

  Read the article

• Booting the liveCD/USB in EFI mode fails on Samsung Tablet XE700T1A

  - by F.L.

  My tablet is Samsung Series 7 Slate (XE700T1A-A02FR (French Language)). It operates an Intel Sandy Bridge architecture. The main issue about this tablet is that it ships with an installed Windows 7 in (U)EFI mode (GPT partition table, etc.), so I'd like to get an EFI dual boot with Ubuntu. But it seems I can't boot on the liveCD in EFI mode. It starts loading (up to initrd), but I then get a blank (black) screen. I've tried the nomodeset kernel option (as well as removing quiet and splash) with no luck. [2012-09-27] I have used the Ubuntu 12.04.1 Desktop ISO (I have read somewhere that it is the only one that can boot in EFI mode). I'd say this has something to do with UEFI since the LiveCD boots in bios mode but not in efi mode. Besides, I am not sure my boot info will help, since I can't boot the LiveCD in EFI mode. As a result I can't install ubuntu in EFI mode. So it would be the boot info from the liveCD boot in bios mode. This happens on a ubuntu-12.04.1-desktop-amd64 iso used on a LiveUSB. Live USB was created by dd'ing the iso onto the full disk device (i.e. /dev/sdx no number) of the Flash drive. I have also tried copying the LiveCD files on a primary GPT partition, but with no luck, I just get the grub shell, no menu, no install option. [2012-09-28] I tried today a flash drive created with Ubuntu's Startup Disk Creator and the alternate 12.04.1 64 bit ISO. I get a grub menu in text mode (which meens it did start in efi mode) with install options / test options. But when I start any of these, I simply get a black screen (no cursor, neither mouse nor text-mode cursor). I tried removing the 'quiet' option and adding nomodeset and acpi=off, but it didn't do any good. So this is the same result as for the LiveCD. [2012-10-01] I have tried with a version of the secure remix version via usb-creator-gtk. The boot on the USB key has the same symptoms. Boot in EFI mode is impossible (I have menu but whatever entry I choose, I get the blank screen problem). The boot in BIOS mode works, I did the install. Then I used boot-repair to try installing grub-efi and get a system that would boot in efi mode. But I can't boot this system, because the EFI firmware doesn't seem to detect that sda contains a valid efi partition. Here is the resulting boot-info Boot info 1253554 [2012-10-01] Today, I have reinstalled the pre-shipped version of windows 7, and then installed ubuntu from a secure-remix iso dumped on USB flash drive vie usb-creator-gtk booted in BIOS mode. When install ended, I said "continue testing" then I used boot-repair to try get the bootloader installed. Now, when I boot the tablet, I get the grub menu, it can chainload windows 7 flawlessly. But when I try to start one of the ubuntu options I get the same old blank screen. Here is the new boot-info: Boot info 1253927 [2012-10-01] I tried installing the 3.3 kernel by chrooting a live usb boot (secure remix again) into the installed system. Same symptoms. I feel the key to this is that the device's efi firmware (which is EFI v2.0) would expose the graphics hardware in a way that prevents the kernel to initialize it, and thus prevents it from booting (the kernel stops all drive access just after the screen turns kind of very dark purple). Here is some info on the UEFI firmware as given by rEFInd: EFI revision: 2.00 Platform: x86_64 (64 bit) Firmware: American Megatrends 4.635 Screen Output: Graphics Output (UEFI), 800x600 [2012-10-08] This week end I tried loading the kernel with elilo. Eventhough I didn't have more luck on booting the kernel, elilo gives more info when loading the kernel. I think the next step is trying to load a kernel with EFI stub directly.

  Read the article

• Graphics trouble after resuming from hibernate or suspend

  - by Voyagerfan5761

  I have a Dell Inspiron 2650 (with NVidia graphics, using nouveau drivers) that I'm using to try out Ubuntu. It's all great, except that Hibernate and Suspend aren't usable. Yes, I know that questions about power-save issues are rampant in the Linux support universe, but it seems that every time I find a solution it's for a very specific hardware combination and doesn't apply to me. So anyway, here goes. When I resume from either power-saving mode, I'll get graphics problems anywhere on the range from a few scattered random-colored pixels that won't change; all the way to full-screen patterns that don't change as I move the mouse, hit keys on the keyboard, or even bring up the shutdown dialog using the power button. Those full-screen issues (which may involve stripes with random pixels, partial black screen, or both) always end in me forcing the machine to shut down by holding the power button. I haven't done much testing yet to determine what severity level is most commonly associated with each mode, but I do avoid using either power-save option because of these issues. I'll add info on my hardware as I can gather it (no home internet connection, and this laptop is tethered to my desk by a dead battery and casing degradation). Please feel free to request something specific in the question comments. Hardware Info See this hardinfo report for my system's hardware configuration. (No, my username is not "myuser"; I sanitized hardinfo's output before publishing it.) Screenshots These screenshots are from a relatively mild occurrence, which happened after the second hibernation I took that session. The first one worked great, though I used the wireless card and Firefox heavily between the two hibernation attempts. Take a look at what happened when I opened my home directory in Nautilus and scrolled it: See below for the situations I've tested so far. The real trouble comes when the machine resumes to an unusable state; in such cases I can't even unlock the screen or properly reboot, much less take a screenshot. I have a hunch that putting a CD in the drive will cause such major failures, and I will try that at some point; see related question. Situations Tested Maverick (10.10) Suspend Seems to suspend nicely with nothing running Seems to suspend nicely with flash drive plugged in On resume from suspend with no flash drive, Terminal and gedit running: Funky graphics on top of log output, then blank screen with pixelated cursor; no response to power button (normally will shutdown 60 seconds later) Hibernate Seems to hibernate nicely with nothing running Seems to hibernate nicely with a few apps (Terminal, Mouse preferences) running Seems to not hibernate when flash drive plugged in Seems to not hibernate when System Monitor is running Have encountered failed hibernation (after several hours and one successful hibernate/thaw cycle) with no external media connected and no programs running except normal background stuff Natty LiveCD (11.04_2010-12-22) When I tested it, Natty wouldn't stay logged in. It played part of the login sound and then [ OK ] appeared in the top right corner (white-on-black terminal text) for a few seconds. Then it kicked me back to the Unlock screen. It did that four times before I gave up and just tested suspend from the Unlock screen. Suspend Resumed to vertical gray and black lines 2px (?) wide, then shifted to vertical "jail bars" of black over a black screen with above-described random pixels and mouse pointer. No apparent response to input from mouse (clicking randomly). Keyboard and touchpad unrecognized.

  Read the article

• Moving data files failing

  - by Miles Hayler

  Trying to migrate data from C: to D: via the SBS console is failing. The wizard starts running but drops out in the first few seconds. I'll post the full logs, but the important lines appear to be as follows: An exception of type 'Type: System.IO.FileNotFoundException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' has occurred. Message: The system cannot find the file specified. (Exception from HRESULT: 0x80070002) Stack: at TaskScheduler.TaskSchedulerClass.GetFolder(String Path) at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) BaseException: Microsoft.WindowsServerSolutions.Storage.Common.StorageException: GetServerBackupTaskStatus: fail to find the task --- ErrorCode:0 I've been googling for days with no luck. I have found that mscorlib is a component of .net, and I've discovered multiple instances of the file in %windir%, %windir%\winsxs, %windir%\Microsoft.net Anyone come across and fixed this one before? --------------------------------------------------------- [1516] 110315.190856.1105: Storage: Initializing...C:\Program Files\Windows Small Business Server\Bin\MoveData.exe [1516] 110315.190856.2875: Storage: Data Store to be moved: Exchange [1516] 110315.190856.5305: TaskScheduler: Exception System.IO.FileNotFoundException: [1516] 110315.190856.5605: Exception: --------------------------------------- An exception of type 'Type: System.IO.FileNotFoundException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' has occurred. Timestamp: 03/15/2011 19:08:56 Message: The system cannot find the file specified. (Exception from HRESULT: 0x80070002) Stack: at TaskScheduler.TaskSchedulerClass.GetFolder(String Path) at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) [1516] 110315.190856.5625: Storage: Exception Microsoft.WindowsServerSolutions.Common.WindowsTaskSchedulerException: [1516] 110315.190856.5635: Exception: --------------------------------------- [b]An exception of type 'Type: Microsoft.WindowsServerSolutions.Common.WindowsTaskSchedulerException, Common, Version=6.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' has occurred.[/b] Timestamp: 03/15/2011 19:08:56 Message: Failed to find the task path Stack: at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) at Microsoft.WindowsServerSolutions.Storage.Common.ServerBackupUtility.GetServerBackupTaskStatus() --------------------------------------- An exception of type 'Type: System.IO.FileNotFoundException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' has occurred. Timestamp: 03/15/2011 19:08:56 Message: The system cannot find the file specified. (Exception from HRESULT: 0x80070002) Stack: at TaskScheduler.TaskSchedulerClass.GetFolder(String Path) at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) [1516] 110315.190856.5665: Storage: Error Retrieving Server Backup Task Status: ErrorCode:0 BaseException: Microsoft.WindowsServerSolutions.Storage.Common.StorageException: GetServerBackupTaskStatus: fail to find the task ---> ErrorCode:0 BaseException: Microsoft.WindowsServerSolutions.Common.WindowsTaskSchedulerException: Failed to find the task path ---> System.IO.FileNotFoundException: The system cannot find the file specified. (Exception from HRESULT: 0x80070002) at TaskScheduler.TaskSchedulerClass.GetFolder(String Path) at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Common.WindowsTaskScheduler..ctor(String taskPath, String taskName) at Microsoft.WindowsServerSolutions.Storage.Common.ServerBackupUtility.GetServerBackupTaskStatus() --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Storage.Common.ServerBackupUtility.GetServerBackupTaskStatus() at Microsoft.WindowsServerSolutions.Storage.MoveData.Helper.get_ServerBackupTaskState() [1516] 110315.190857.6216: Storage: Backup Task State: Unknown [1516] 110315.190857.9347: Storage: Launching the Move Data Wizard! [1516] 110315.190857.9397: Wizard: Admin:QueryNextPage(null) = Storage.MoveDataWizard.GettingStartedPage [1516] 110315.190857.9417: Wizard: TOC Storage.MoveDataWizard.GettingStartedPage is on ExpectedPath [1516] 110315.190857.9577: Wizard: Storage.MoveDataWizard.GettingStartedPage entered [1516] 110315.190857.9657: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.GettingStartedPage) = Storage.MoveDataWizard.DiagnoseDataStorePage [1516] 110315.190857.9657: Wizard: TOC Storage.MoveDataWizard.DiagnoseDataStorePage is on ExpectedPath [1516] 110315.190857.9657: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.DiagnoseDataStorePage) = Storage.MoveDataWizard.NewDataStoreLocationPage [1516] 110315.190857.9657: Wizard: TOC Storage.MoveDataWizard.NewDataStoreLocationPage is on ExpectedPath [1516] 110315.190857.9657: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.NewDataStoreLocationPage) = null [1516] 110315.190857.9697: Wizard: ---------------------------------- [1516] 110315.190857.9697: Wizard: The pages visted: [1516] 110315.190857.9697: Wizard: Current Page := [TOC Storage.MoveDataWizard.GettingStartedPage] [1516] 110315.190857.9697: Wizard: [TOC] : TOC Storage.MoveDataWizard.DiagnoseDataStorePage [1516] 110315.190857.9697: Wizard: [TOC] : TOC Storage.MoveDataWizard.NewDataStoreLocationPage [1516] 110315.190857.9697: Wizard: Step 1 of 3 [1516] 110315.190907.0406: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.GettingStartedPage) = Storage.MoveDataWizard.DiagnoseDataStorePage [1516] 110315.190907.0416: Wizard: Storage.MoveDataWizard.GettingStartedPage exited with the button: Next [1516] 110315.190907.0416: WizardChainEngine Next Clicked: Going to page {0}.: Storage.MoveDataWizard.DiagnoseDataStorePage [1516] 110315.190907.0496: Wizard: Storage.MoveDataWizard.DiagnoseDataStorePage entered [1516] 110315.190907.0606: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.DiagnoseDataStorePage) = Storage.MoveDataWizard.NewDataStoreLocationPage [1516] 110315.190907.0606: Wizard: Admin:QueryNextPage(Storage.MoveDataWizard.NewDataStoreLocationPage) = null [1516] 110315.190907.0606: Wizard: ---------------------------------- [1516] 110315.190907.0606: Wizard: The pages visted: [1516] 110315.190907.0606: Wizard: [TOC] visited: TOC Storage.MoveDataWizard.GettingStartedPage [1516] 110315.190907.0606: Wizard: Current Page := [TOC Storage.MoveDataWizard.DiagnoseDataStorePage] [1516] 110315.190907.0616: Wizard: [TOC] : TOC Storage.MoveDataWizard.NewDataStoreLocationPage [1516] 110315.190907.0616: Wizard: Step 2 of 3 [19772] 110315.190907.0656: Storage: Starting System Diagnosis [19772] 110315.190907.0656: Storage: Getting Data Store Information [19772] 110315.190907.1086: Storage: Create the list of storage and DB directory path [19772] 110315.190907.1246: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingTasks..ctor [19772] 110315.190907.1546: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingTasks.Initialize [19772] 110315.190907.1596: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.Initialize [19772] 110315.190907.1606: Messaging: Exchange install path: C:\Program Files\Microsoft\Exchange Server\bin [19772] 110315.190908.4157: Messaging: E12 Monad runspace created ID: Microsoft.PowerShell [19772] 110315.190908.4237: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190908.4287: Messaging: Executed management shell command: get-exchangeserver [19772] 110315.190910.2369: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190910.2369: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.Initialize [19772] 110315.190910.5699: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingTasks.GatherAdminInfo [19772] 110315.190910.5699: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190910.5719: Messaging: Executed management shell command: get-user -Identity "dmagroup.local\Administrator" [19772] 110315.190911.0870: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.0880: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.0880: Messaging: Executed management shell command: get-mailbox -Identity "d2ae2bf0-48a7-4ce9-9e72-bb3c765454ac" [19772] 110315.190911.1300: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.1310: Messaging: User Administrator is mail enabled and can use MessagingManagement to send mail. [19772] 110315.190911.1310: Messaging: Email address used for user: [email protected] [19772] 110315.190911.1440: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.1440: Messaging: Executed management shell command: get-group -Identity "Domain Admins" [19772] 110315.190911.1630: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.1640: Messaging: User Administrator is a member of Domain Admins and can use MessagingManagement to manage Exchange. [19772] 110315.190911.1640: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingTasks.GatherAdminInfo [19772] 110315.190911.1640: Messaging: MessagingManagement enabled for Exchange management: True [19772] 110315.190911.1640: Messaging: MessagingManagement enabled for mail submission: True [19772] 110315.190911.1640: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingTasks.Initialize [19772] 110315.190911.1640: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Tasks.TaskMoveExchangeData.CreateDataStoreDriveList [19772] 110315.190911.1670: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.Initialize [19772] 110315.190911.1670: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.1670: Messaging: Executed management shell command: get-storagegroup -Server "SERVER01" [19772] 110315.190911.2990: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.3070: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.Initialize [19772] 110315.190911.3070: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.3070: Messaging: Executed management shell command: get-mailboxdatabase -Server "SERVER01" [19772] 110315.190911.4440: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.4520: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.Initialize [19772] 110315.190911.4520: Messaging: Begin Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.4520: Messaging: Executed management shell command: get-publicfolderdatabase -Server "SERVER01" [19772] 110315.190911.5240: Messaging: End Microsoft.WindowsServerSolutions.Messaging.Management.MessagingRunspace.StaticExecute [19772] 110315.190911.5510: Storage: Data Store Drive/s Details:Name=C:\,Size=12675712420 [19772] 110315.190911.5510: Storage: Data Store Size Details: Current Total Size=12675712420 Required Size=12675712420 [19772] 110315.190911.5510: Storage: MoveData Task can move the Data Store=True [19772] 110315.190911.8401: Storage: An error was encountered when performing system diagnosis : ErrorCode:0 BaseException: Microsoft.WindowsServerSolutions.Storage.Common.StorageException: WMI error occurred while accessing drive ---> System.Management.ManagementException: Not found at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode) at System.Management.ManagementObjectCollection.ManagementObjectEnumerator.MoveNext() at Microsoft.WindowsServerSolutions.Storage.Common.DriveUtil.IsDriveRemovable(String drive) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Storage.Common.DriveUtil.IsDriveRemovable(String drive) at Microsoft.WindowsServerSolutions.Storage.Common.DataStoreInfo.LoadAvailableDrives() at Microsoft.WindowsServerSolutions.Storage.Common.MoveDataUtil.CanMoveData(DataStoreInfo storeInfo, MoveDataError& error) at Microsoft.WindowsServerSolutions.Storage.MoveData.DiagnoseDataStorePagePresenter.DiagnoseDataStore(Object sender, DoWorkEventArgs args) [1516] 110315.190912.0331: Storage: An error occured during the execution: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> ErrorCode:0 BaseException: Microsoft.WindowsServerSolutions.Storage.Common.StorageException: Diagnosing the Data Store failed (see the inner exception) ---> ErrorCode:0 BaseException: Microsoft.WindowsServerSolutions.Storage.Common.StorageException: WMI error occurred while accessing drive ---> System.Management.ManagementException: Not found at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode) at System.Management.ManagementObjectCollection.ManagementObjectEnumerator.MoveNext() at Microsoft.WindowsServerSolutions.Storage.Common.DriveUtil.IsDriveRemovable(String drive) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Storage.Common.DriveUtil.IsDriveRemovable(String drive) at Microsoft.WindowsServerSolutions.Storage.Common.DataStoreInfo.LoadAvailableDrives() at Microsoft.WindowsServerSolutions.Storage.Common.MoveDataUtil.CanMoveData(DataStoreInfo storeInfo, MoveDataError& error) at Microsoft.WindowsServerSolutions.Storage.MoveData.DiagnoseDataStorePagePresenter.DiagnoseDataStore(Object sender, DoWorkEventArgs args) at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Storage.MoveData.DiagnoseDataStorePagePresenter.backgroundWorker_RunWorkerCompleted(Object sender, RunWorkerCompletedEventArgs e) --- End of inner exception stack trace --- at System.RuntimeMethodHandle._InvokeMethodFast(Object target, Object[] arguments, SignatureStruct& sig, MethodAttributes methodAttributes, RuntimeTypeHandle typeOwner) at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture, Boolean skipVisibilityChecks) at System.Delegate.DynamicInvokeImpl(Object[] args) at System.Windows.Forms.Control.InvokeMarshaledCallbackDo(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbackHelper(Object obj) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Forms.Control.InvokeMarshaledCallback(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbacks() at System.Windows.Forms.Control.WndProc(Message& m) at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m) at System.Windows.Forms.NativeWindow.DebuggableCallback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam) at System.Windows.Forms.UnsafeNativeMethods.DispatchMessageW(MSG& msg) at System.Windows.Forms.Application.ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(Int32 dwComponentID, Int32 reason, Int32 pvLoopData) at System.Windows.Forms.Application.ThreadContext.RunMessageLoopInner(Int32 reason, ApplicationContext context) at System.Windows.Forms.Application.ThreadContext.RunMessageLoop(Int32 reason, ApplicationContext context) at Microsoft.WindowsServerSolutions.Common.Wizards.Framework.WizardFrameView.Create() at Microsoft.WindowsServerSolutions.Common.Wizards.Framework.WizardChainEngine.Launch() at Microsoft.WindowsServerSolutions.Storage.MoveData.MainClass.LaunchMoveDataWizard() at Microsoft.WindowsServerSolutions.Storage.MoveData.MainClass.Main(String[] args)

  Read the article

• How do I repair the corrupted files found by sfc /scannow? "Windows Resource Protection found corrupt files but was unable to fix some of them."

  - by galacticninja

  After running chkdsk C: /F /R and finding out that my hard disk has 24 KB in bad sectors (log is posted below), I decided to run Windows 7's System File Checker utility (sfc /scannow). SFC showed the ff. message after I ran it: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log." Since the CBS.log file is too large, I ran findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt" (as per Microsoft's KB 928228 article) to only get the log text pertaining to the corrupt files. (log is also posted below) How do I troubleshoot and repair the corrupted files mentioned by sfc /scannow? My OS is Windows 7, 64-bit. chkdsk log Checking file system on C: The type of the file system is NTFS. A disk check has been scheduled. Windows will now check the disk. CHKDSK is verifying files (stage 1 of 5)... 936192 file records processed. File verification completed. 25238 large file records processed. 0 bad file records processed. 4 EA records processed. 44 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 1051640 index entries processed. Index verification completed. 0 unindexed files scanned. 0 unindexed files recovered. CHKDSK is verifying security descriptors (stage 3 of 5)... 936192 file SDs/SIDs processed. Cleaning up 24 unused index entries from index $SII of file 0x9. Cleaning up 24 unused index entries from index $SDH of file 0x9. Cleaning up 24 unused security descriptors. Security descriptor verification completed. 57725 data files processed. CHKDSK is verifying Usn Journal... 36994248 USN bytes processed. Usn Journal verification completed. CHKDSK is verifying file data (stage 4 of 5)... 936176 files processed. File data verification completed. CHKDSK is verifying free space (stage 5 of 5)... 306238 free clusters processed. Free space verification is complete. Adding 1 bad clusters to the Bad Clusters File. Correcting errors in the Volume Bitmap. Windows has made corrections to the file system. 488282111 KB total disk space. 485595420 KB in 766458 files. 401856 KB in 57726 indexes. 24 KB in bad sectors. 1059863 KB in use by the system. 65536 KB occupied by the log file. 1224948 KB available on disk. 4096 bytes in each allocation unit. 122070527 total allocation units on disk. 306237 allocation units available on disk. Internal Info: 00 49 0e 00 81 93 0c 00 34 01 17 00 00 00 00 00 .I......4....... 6b 29 00 00 2c 00 00 00 00 00 00 00 00 00 00 00 k)..,........... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ sfc /scannow log (through findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt") Note: The full log is at http://pastebin.com/raw.php?i=gTEGZmWj . I've only quoted parts of the full log below (mostly from the last part), as the full log won't fit within the character limit for questions. I've added it to serve as a preview. ... 2013-12-28 19:37:50, Info CSI00000542 [SR] Beginning Verify and Repair transaction 2013-12-28 19:37:55, Info CSI00000544 [SR] Verify complete 2013-12-28 19:37:56, Info CSI00000545 [SR] Verifying 95 (0x000000000000005f) components 2013-12-28 19:37:56, Info CSI00000546 [SR] Beginning Verify and Repair transaction 2013-12-28 19:38:03, Info CSI00000548 [SR] Verify complete 2013-12-28 19:38:03, Info CSI00000549 [SR] Repairing 43 (0x000000000000002b) components 2013-12-28 19:38:03, Info CSI0000054a [SR] Beginning Verify and Repair transaction ... 2013-12-28 19:38:15, Info CSI00000730 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:62{31}]"GroupPolicy-Admin-Gpedit-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000733 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:30{15}]"frs-core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000736 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"gpmgmt-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000739 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:74{37}]"MediaServer-ASPAdmin-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073c [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:36{18}]"Ldap-Client-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073f [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"iSNS_Service-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000742 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"MediaServer-Multicast-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000745 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:78{39}]"Kerberos-Key-Distribution-Center-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000748 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:86{43}]"GroupPolicy-CSE-SoftwareInstallation-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074b [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:28{14}]"ieframe-dl.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074e [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"GroupPolicy-Admin-Gpedit-Snapin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000751 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:32{16}]"IPSec-Svc-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000754 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:22{11}]"HTTP-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000757 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:56{28}]"MediaServer-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075a [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"GPBase-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075d [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"IasMigPlugin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000760 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:50{25}]"International-Core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000762 [SR] Cannot repair member file [l:24{12}]"wbemdisp.dll" of Microsoft-Windows-WMI-Scripting, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000763 [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000766 [SR] Could not reproject corrupted file [ml:58{29},l:56{28}]"\??\C:\Windows\SysWOW64\wbem"\[l:24{12}]"wbemdisp.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000768 [SR] Cannot repair member file [l:56{28}]"Microsoft.MediaCenter.UI.dll" of Microsoft.MediaCenter.UI, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_MSIL (8), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000769 [SR] This component was referenced by [l:176{88}]"Microsoft-Windows-MediaCenter-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.MediaCenter" 2013-12-28 19:38:16, Info CSI0000076c [SR] Could not reproject corrupted file [ml:520{260},l:40{20}]"\??\C:\Windows\ehome"\[l:56{28}]"Microsoft.MediaCenter.UI.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000076e [SR] Cannot repair member file [l:24{12}]"ReAgentc.exe" of Microsoft-Windows-WinRE-RecoveryTools, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000076f [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000772 [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:24{12}]"ReAgentc.exe"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000774 [SR] Cannot repair member file [l:82{41}]"System.Management.Automation.dll-Help.xml" of Microsoft-Windows-PowerShell-PreLoc.Resources, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture = [l:10{5}]"en-US", VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000775 [SR] This component was referenced by [l:266{133}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~en-US~6.1.7601.17514.Microsoft-Windows-Client-Features-Language-Pack" 2013-12-28 19:38:16, Info CSI00000778 [SR] Could not reproject corrupted file [ml:520{260},l:104{52}]"\??\C:\Windows\System32\WindowsPowerShell\v1.0\en-US"\[l:82{41}]"System.Management.Automation.dll-Help.xml"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000077a [SR] Cannot repair member file [l:18{9}]"hlink.dll" of Microsoft-Windows-HLink, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000077b [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI0000077e [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:18{9}]"hlink.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000780 [SR] Repair complete 2013-12-28 19:38:16, Info CSI00000781 [SR] Committing transaction 2013-12-28 19:38:19, Info CSI00000785 [SR] Verify and Repair Transaction completed. All files and registry keys listed in this transaction have been successfully repaired

  Read the article

• MySQL query, 2 similar servers, 2 minute difference in execution times

  - by mr12086

  I had a similar question on stack overflow, but it seems to be more server/mysql setup related than coding. The queries below all execute instantly on our development server where as they can take upto 2 minutes 20 seconds. The query execution time seems to be affected by home ambiguous the LIKE string's are. If they closely match a country that has few matches it will take less time, and if you use something like 'ge' for germany - it will take longer to execute. But this doesn't always work out like that, at times its quite erratic. Sending data appears to be the culprit but why and what does that mean. Also memory on production looks to be quite low (free memory)? Production: Intel Quad Xeon E3-1220 3.1GHz 4GB DDR3 2x 1TB SATA in RAID1 Network speed 100Mb Ubuntu Development Intel Core i3-2100, 2C/4T, 3.10GHz 500 GB SATA - No RAID 4GB DDR3 UPDATE 2 : mysqltuner output: [prod] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.61-0ubuntu0.10.04.1 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 103M (Tables: 180) [--] Data in InnoDB tables: 491M (Tables: 19) [!!] Total fragmented tables: 38 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 77d 4h 6m 1s (53M q [7.968 qps], 14M conn, TX: 87B, RX: 12B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (12K/53M) [OK] Highest usage of available connections: 22% (34/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/10.6M [OK] Key buffer hit rate: 98.7% (162M cached / 2M reads) [OK] Query cache efficiency: 20.7% (7M cached / 36M selects) [!!] Query cache prunes per day: 3934 [OK] Sorts requiring temporary tables: 1% (3K temp sorts / 230K sorts) [!!] Joins performed without indexes: 71068 [OK] Temporary tables created on disk: 24% (3M on disk / 13M total) [OK] Thread cache hit rate: 99% (690 created / 14M connections) [!!] Table cache hit rate: 0% (64 open / 85M opened) [OK] Open file limit used: 12% (128/1K) [OK] Table locks acquired immediately: 99% (16M immediate / 16M locks) [!!] InnoDB data size / buffer pool: 491.9M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) join_buffer_size (> 128.0K, or always use indexes with joins) table_cache (> 64) innodb_buffer_pool_size (>= 491M) [dev] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.62-0ubuntu0.11.10.1 [!!] Switch to 64-bit OS - MySQL cannot currently use all of your RAM -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 185M (Tables: 632) [--] Data in InnoDB tables: 967M (Tables: 38) [!!] Total fragmented tables: 73 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 2h 26m 9s (5K q [0.058 qps], 1K conn, TX: 4M, RX: 1M) [--] Reads / Writes: 99% / 1% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (0/5K) [OK] Highest usage of available connections: 1% (2/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/18.6M [OK] Key buffer hit rate: 99.9% (60K cached / 36 reads) [OK] Query cache efficiency: 44.5% (1K cached / 2K selects) [OK] Query cache prunes per day: 0 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 44 sorts) [OK] Temporary tables created on disk: 24% (162 on disk / 666 total) [OK] Thread cache hit rate: 99% (2 created / 1K connections) [!!] Table cache hit rate: 1% (64 open / 4K opened) [OK] Open file limit used: 8% (88/1K) [OK] Table locks acquired immediately: 100% (1K immediate / 1K locks) [!!] InnoDB data size / buffer pool: 967.7M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: table_cache (> 64) innodb_buffer_pool_size (>= 967M) UPDATE 1: When testing the queries listed here there is usually no more than one other query taking place, and usually none. Because production is actually handling apache requests that development gets very few of as it's only myself and 1 other who accesses it - could the 4GB of RAM be getting exhausted by using the single machine for both apache and mysql server? Production: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 24872 MB in 2.00 seconds = 12450.72 MB/sec Timing buffered disk reads: 368 MB in 3.00 seconds = 122.49 MB/sec sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 24786 MB in 2.00 seconds = 12407.22 MB/sec Timing buffered disk reads: 350 MB in 3.00 seconds = 116.53 MB/sec Server version(mysql + ubuntu versions): 5.1.61-0ubuntu0.10.04.1 Development: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 10632 MB in 2.00 seconds = 5319.40 MB/sec Timing buffered disk reads: 400 MB in 3.01 seconds = 132.85 MB/sec Server version(mysql + ubuntu versions): 5.1.62-0ubuntu0.11.10.1 ORIGINAL DATA : This query is NOT the query in question but is related so ill post it. SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' And the explain plan for the above query is, run on both dev and production produce the same plan. +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | 1 | SIMPLE | p2 | const | PRIMARY | PRIMARY | 4 | const | 1 | Using index | | 1 | SIMPLE | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | const | 796 | Using where | | 1 | SIMPLE | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using index | | 1 | SIMPLE | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 1 | SIMPLE | f2 | ref | form_project_id | form_project_id | 4 | const | 15 | Using where | | 1 | SIMPLE | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ This query takes 2 minutes ~20 seconds to execute. The query that is ACTUALLY being run on the server is this one: SELECT COUNT(*) AS num_results FROM (SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' GROUP BY f.form_question_has_answer_id;) dctrn_count_query; With explain plans (again same on dev and production): +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | 1 | PRIMARY | NULL | NULL | NULL | NULL | NULL | NULL | NULL | Select tables optimized away | | 2 | DERIVED | p2 | const | PRIMARY | PRIMARY | 4 | | 1 | Using index | | 2 | DERIVED | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | | 797 | Using where | | 2 | DERIVED | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id,project_company_has_user_garbage_collection | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 2 | DERIVED | f2 | ref | form_project_id | form_project_id | 4 | | 15 | Using where | | 2 | DERIVED | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | | 2 | DERIVED | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_user_id | 1 | Using where; Using index | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ On the production server the information I have is as follows. Upon execution: +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (2 min 14.28 sec) Show profile: +--------------------------------+------------+ | Status | Duration | +--------------------------------+------------+ | starting | 0.000016 | | checking query cache for query | 0.000057 | | Opening tables | 0.004388 | | System lock | 0.000003 | | Table lock | 0.000036 | | init | 0.000030 | | optimizing | 0.000016 | | statistics | 0.000111 | | preparing | 0.000022 | | executing | 0.000004 | | Sorting result | 0.000002 | | Sending data | 136.213836 | | end | 0.000007 | | query end | 0.000002 | | freeing items | 0.004273 | | storing result in query cache | 0.000010 | | logging slow query | 0.000001 | | logging slow query | 0.000002 | | cleaning up | 0.000002 | +--------------------------------+------------+ On development the results are as follows. +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (0.08 sec) Again the profile for this query: +--------------------------------+----------+ | Status | Duration | +--------------------------------+----------+ | starting | 0.000022 | | checking query cache for query | 0.000148 | | Opening tables | 0.000025 | | System lock | 0.000008 | | Table lock | 0.000101 | | optimizing | 0.000035 | | statistics | 0.001019 | | preparing | 0.000047 | | executing | 0.000008 | | Sorting result | 0.000005 | | Sending data | 0.086565 | | init | 0.000015 | | optimizing | 0.000006 | | executing | 0.000020 | | end | 0.000004 | | query end | 0.000004 | | freeing items | 0.000028 | | storing result in query cache | 0.000005 | | removing tmp table | 0.000008 | | closing tables | 0.000008 | | logging slow query | 0.000002 | | cleaning up | 0.000005 | +--------------------------------+----------+ If i remove user and/or project innerjoins the query is reduced to 30s. Last bit of information I have: Mysqlserver and Apache are on the same box, there is only one box for production. Production output from top: before & after. top - 15:43:25 up 78 days, 12:11, 4 users, load average: 1.42, 0.99, 0.78 Tasks: 162 total, 2 running, 160 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 50.4%sy, 0.0%ni, 49.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3772580k used, 265288k free, 243704k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207944k cached top - 15:44:31 up 78 days, 12:13, 4 users, load average: 1.94, 1.23, 0.87 Tasks: 160 total, 2 running, 157 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 50.6%sy, 0.0%ni, 49.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3834300k used, 203568k free, 243736k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207804k cached But this isn't a good representation of production's normal status so here is a grab of it from today outside of executing the queries. top - 11:04:58 up 79 days, 7:33, 4 users, load average: 0.39, 0.58, 0.76 Tasks: 156 total, 1 running, 155 sleeping, 0 stopped, 0 zombie Cpu(s): 3.3%us, 2.8%sy, 0.0%ni, 93.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3676136k used, 361732k free, 271480k buffers Swap: 3905528k total, 268736k used, 3636792k free, 1063432k cached Development: This one doesn't change during or after. top - 15:47:07 up 110 days, 22:11, 7 users, load average: 0.17, 0.07, 0.06 Tasks: 210 total, 2 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4111972k total, 1821100k used, 2290872k free, 238860k buffers Swap: 4183036k total, 66472k used, 4116564k free, 921072k cached

  Read the article

• DataContractSerializer and deserializing web service response types

  - by matra

  Hi, I am using calling web services and using WCF generated service-reference on the client. I have saved XML responses that are received from test service to disk (without SOAP envelope and body tags) I would like to load them from disk and create objects from them. Lets' take the following method from my web service: SomeMethodResponse SomeMethod(SomeMethodRequest req) I manually (through SOAP UI) save the response to disk to file, Sample response: < SomeMethodResponse xmlns="http://myNamespace"> <SomeMember1>value</SomeMember1> </SomeMethodResponse xmlns="http://myNamespace"> Then I try to deserialize the object from file using: DataContractSerializer dcs = new DataContractSerializer(typeof(SomeMethodResponse)) This fails – the serializer complains with the error, that it is expecting element in namespace 'http://schemas.datacontract.org/2004/07', but found element in 'http://myNamespace'. Question: Why does the DataContractSerializer not use the namespace, that is declared on SomeMethodResponseType with XmlTypeAttribute(Namespace="http://myNamespace")? I can work around this by explicitly providing the namespace and the root element to DataContractSerializer constructor. But then it fails with message similar to: Error in line X position Y (last line of the XMLdocument). 'EndElement' 'SomeMethodResponse from namespace 'httpmyNapespace’ is not expected. Expecting element 'someNameField'. SomeName is an element in the XSD that web service is using. It is also a property on the SomeMethodResponse type, backed by the private field called someNameField. It looks like DataContractSerializer is trying to deserialize the fields in addition to properties. How can I deserailize XML that I have saved from disk and get back the object of same type that SomeMethod is returning? Thanks, Matra

  Read the article

• WNetAddConnection2 in Windows 7 with Impersonation and no Error Code

  - by Adam Driscoll

  I'm doing some crazy impersonation stuff to get around UAC dialogs in Windows 7 so the user does not have to interact with the UI (I have the admin creds of course). I have a process running as the Administrator and elevated past UAC. The issue that I'm facing is that when I make a call to WNetAddConnection2, within this process, I am not getting a new mapped net drive. The function returns ERROR_SUCCESS but no net drive is visible. We have another method of adding network drives using 'subst' but this, again, returns successful does does not add a net drive. I have tried to use the default user (which is the Administrator because of process's security context) and I have tried using specific user credentials. I can map the drive just fine through Explorer. Of course the same functionality works fine in XP/2003. I haven't got around to testing on Vista because of issues with impersonation that are limiting my ability to spin up the process. Are there unique Windows 7 limits on this function? MSDN does not glean any that I can find. Any help would be greatly appreciated!

  Read the article

• Visual studio 2010 setup project problem.

  - by Guru

  Hi there, I've made an application that uses .NET framework 3.5 SP1 and SQL Server 2008 Express. Application is fine and now i'm going to to make a setup project for this. When I first build my setup it was fine as all the prerequisites were not included in setup. But I want my setup to install .NET 3.5 SP1 and SQL SERVER 2008 Express also. So for this I've changed the options in setup project's properties from "Download prerequisites from following location" to "Download prerequisites from the same location as my application". In addition to that I've also checked the options above like .NET 3.5 SP1 and SQL Server 2008 Express etc. After doing all this I build my project again. This time I'm Getting 57 Errors. Error 1 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\aspnet.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 2 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\aspnet_64.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 3 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\clr.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 4 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\clr_64.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup As the question will become too large so I'm just pasting 3 errors but there are totally 57 errors. Please help me . Thanks in advance Guru

  Read the article

• What strategy do you use to sync your code when working from home

  - by Ben Daniel

  At my work I currently have my development environment inside a Virtual Machine. When I need to do work from home I copy my VM and any databases I need onto a laptop drive sized external USB drive. After about 10 minutes of copying I put the drive in my pocket and head home, copy back the VM and databases onto my personal computer and I'm ready to work. I follow the same steps to take the work back with me. So if I count the total amount of time I spend waiting around for files to finish copying in order for me to take work home and bring it back again, it comes to around 40 minutes! I do have a VPN connection to my work from home (providing the internet is up at both sites) and a decent internet speed (8mbits down/?up) but I find Remote Desktoping into my work machine laggy enough for me to want to work on my VM directly. So in looking at what other options I have or how I could improve my existing option I'm interested in what strategy you use or recommend to do work at home and keeping your code/environment in sync. EDIT: I'd prefer an option where I don't have to commit my changes into version control before I leave work - as I like to make meaningful descriptive comments in my commits, committing would take longer than just copying my VM onto a portable drive! lol Also I'd prefer a solution where my dev environment stays in sync too. Having said that I'm still very interested in your own solutions even if they don't exactly solve my problem as best as I'd like. :)

  Read the article

• Out of Core Implementation of a Quadtree

  - by Nima

  Hi, I am trying to build a Quadtree data structure(or let's just say a tree) on the secondary memory(Hard Disk). I have a C++ program to do so and I use fopen to create the files. Also, I am using tesseral coding to store each cell in a file named with its corresponding code to store it on the disk in one directory. The problem is that after creating about 1,100 files, fopen just returns NULL and stops creating new files. I can create further files manually in that directory, but using C++ it can not create any further files. I know about max limit of inode on ext3 filesystem which is (from Wikipedia) 32,000 but mine is way less than that, also note that I can create files manually on the disk; just not through fopen. Also, I really appreciate any idea regarding the best way to store a very dynamic quadtree on disk(I need the nodes to be in separate files and the quadtree might have a depth of 50). Using nested directories is one idea, but I think it will slow down the performance because of following the links on the filesystem to access the file. Thanks, Nima

  Read the article

• Problem using custom HttpHandler to process requests for both .aspx and non-extension pages in IIS7

  - by Noel

  I am trying to process both ".aspx" and non-extension page requests (i.e. both contact.aspx and /contact/) using a custom HttpHandler in IIS7. My handler works just fine in either one case or the other, but as soon as I try to process both cases, it only works for one. Please see Handlers snippet from my web.config below: If i keep only mapping to "*.aspx" then all .aspx requests are processed correctly, but obviously extensionless requests won't work: <add name="AllPages.ASPX" path="*.aspx" verb="*" type="Test.PageHandlerFactory, Test" preCondition="" /> If i change the mapping to "*" then all extensionless requests are processed correctly, but ".aspx" requests that should still be handled by this handler stop working. Note that i added the StaticFiles entry in order to process files that are on disk like images, css, js, etc. <add name="WebResource" path="WebResource.axd" verb="GET" type="System.Web.Handlers.AssemblyResourceLoader" /> <add name="StaticFiles" verb="GET,HEAD" path="*.*" type="System.Web.StaticFileHandler" resourceType="File" /> <add name="AllPages" path="*" verb="*" type="Test.PageHandlerFactory, Test" preCondition="" /> The crazy thing is that when i load an ".aspx" request (with the 2nd configuration shown) IIS7 gives a 404 not found error. The error also says that the request is processed by the StaticFiles handler. But I made sure to add resourceType="File" to the StaticFileHandler in order to avoid this. According to MS this means the request is only for "physical files on disk". Am i misreading/interpreting the "on disk" part? My .aspx file isn't on disk, that's why i want to use the handler in the first place.

  Read the article

• SQL Server Clustered Index: (Physical) Data Page Order

  - by scherand

  I am struggling understanding what a clustered index in SQL Server 2005 is. I read the MSDN article Clustered Index Structures (among other things) but I am still unsure if I understand it correctly. The (main) question is: what happens if I insert a row (with a "low" key) into a table with a clustered index? The above mentioned MSDN article states: The pages in the data chain and the rows in them are ordered on the value of the clustered index key. And Using Clustered Indexes for example states: For example, if a record is added to the table that is close to the beginning of the sequentially ordered list, any records in the table after that record will need to shift to allow the record to be inserted. Does this mean that if I insert a row with a very "low" key into a table that already contains a gazillion rows literally all rows are physically shifted on disk? I cannot believe that. This would take ages, no? Or is it rather (as I suspect) that there are two scenarios depending on how "full" the first data page is. A) If the page has enough free space to accommodate the record it is placed into the existing data page and data might be (physically) reordered within that page. B) If the page does not have enough free space for the record a new data page would be created (anywhere on the disk!) and "linked" to the front of the leaf level of the B-Tree? This would then mean the "physical order" of the data is restricted to the "page level" (i.e. within a data page) but not to the pages residing on consecutive blocks on the physical hard drive. The data pages are then just linked together in the correct order. Or formulated in an alternative way: if SQL Server needs to read the first N rows of a table that has a clustered index it can read data pages sequentially (following the links) but these pages are not (necessarily) block wise in sequence on disk (so the disk head has to move "randomly"). How close am I? :)

  Read the article

• loaded resources looks ugly

  - by Xaver

  I have the TreeView class using in my project. I use icons for it.First i load icons so: ImageList^ il = gcnew ImageList(); il->Images->Add(Image::FromFile("DISK.ico")); il->Images->Add(Image::FromFile("FILE.ico")); il->Images->Add(Image::FromFile("FOLDER.ico")); treeView1->ImageList = il; All was good. But i dont like that if i delete my icons from directory of project. there is error in my project. I decide to add icons in .resx file. Now icons loading look so: ImageList^ il = gcnew ImageList(); Resources::ResourceManager^ resourceManager = gcnew Resources::ResourceManager ("FilesSaver.Form1", GetType()->Assembly); Object^ disk = resourceManager->GetObject("DISK"); il->Images->Add(reinterpret_cast<Image^>(disk)); Object^ file = resourceManager->GetObject("FILE"); il->Images->Add(reinterpret_cast<Image^>(file)); Object^ folder = resourceManager->GetObject("FOLDER"); il->Images->Add(reinterpret_cast<Image^>(folder)); treeView1->ImageList = il; And why icons in the TreeView looks ugly (they look lighter and have a big black border). Why did this happen?

  Read the article

• Fastest PNG decoder for .NET

  - by sboisse

  Our web server needs to process many compositions of large images together before sending the results to web clients. This process is performance critical because the server can receive several thousands of requests per hour. Right now our solution loads PNG files (around 1MB each) from the HD and sends them to the video card so the composition is done on the GPU. We first tried loading our images using the PNG decoder exposed by the XNA API. We saw the performance was not too good. To understand if the problem was loading from the HD or the decoding of the PNG, we modified that by loading the file in a memory stream, and then sending that memory stream to the .NET PNG decoder. The difference of performance using XNA or using System.Windows.Media.Imaging.PngBitmapDecoder class is not significant. We roughly get the same levels of performance. Our benchmarks show the following performance results: Load images from disk: 37.76ms 1% Decode PNGs: 2816.97ms 77% Load images on Video Hardware: 196.67ms 5% Composition: 87.80ms 2% Get composition result from Video Hardware: 166.21ms 5% Encode to PNG: 318.13ms 9% Store to disk: 3.96ms 0% Clean up: 53.00ms 1% Total: 3680.50ms 100% From these results we see that the slowest parts are when decoding the PNG. So we are wondering if there wouldn't be a PNG decoder we could use that would allow us to reduce the PNG decoding time. We also considered keeping the images uncompressed on the hard disk, but then each image would be 10MB in size instead of 1MB and since there are several tens of thousands of these images stored on the hard disk, it is not possible to store them all without compression.

  Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >