Search Results

Search found 25093 results on 1004 pages for 'console output'.

Page 265/1004 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

• Laptop battery life drastically decreased compared to Windows 7

  - by Aron Rotteveel

  I am running Ubuntu 10.10 on my Dell Studio XPS 1640 and have about one hour of battery life in it, compared to about 2.5 hours running on Windows 7. This is with wireless and bluetooth on, but still, the difference seems incredible. What could be causing such a difference and is there a way to close the gap without losing core functionality? EDIT: here's some output from powertop. This is with bluetooth turned off and Wifi turned on. The output seems pretty normal to me, but as indicated, this is about 1 hour of battery life on a full battery... Wakeups-from-idle per second : 476.2 interval: 10.0s Power usage (ACPI estimate): 2.5W (1.2 hours) Top causes for wakeups: 30.0% (167.2)D chrome 21.0% (117.3) [extra timer interrupt] 13.9% ( 77.4) [kernel scheduler] Load balancing tick 3.4% ( 18.9)D xchat 7.1% ( 39.8) [iwlagn] <interrupt> 5.9% ( 32.9) AptanaStudio3 3.9% ( 21.6)D java 2.7% ( 14.9) [TLB shootdowns] <kernel IPI> 2.5% ( 14.1) docky 1.8% ( 10.0) nautilus 1.6% ( 9.0) thunderbird-bin 1.0% ( 5.5) [ahci] <interrupt> 0.9% ( 5.0) syndaemon 0.8% ( 4.3) [kernel core] hrtimer_start (tick_sched_timer) EDIT: after changing /proc/sys/vm/laptop_mode to 5 (it was set to 0), wakeups seem to have decreased, although usage still seems far too high: Wakeups-from-idle per second : 263.8 interval: 10.0s Power usage (ACPI estimate): 2.6W (0.9 hours) EDIT: I seem to have discovered the main cause: I was using the open source ATI Drivers. I recently installed the official ATI drivers and laptop battery life seems to have doubled since. EDIT: last edit. The previous 'solution' of installing the official ATI drivers turns out to be a non-solution. Although it does increase battery life, my laptop resolution is maxed out at 1200x800 after a reboot. (Please note that this problem does not need answering in this question as it is a seperate case)

  Read the article

• Low graphics mode error on startup with NVIDIA graphics (12.04 LTS )

  - by champost

  My problem is similar to two other posts concerning ATI cards and 12.04 LTS: Post1 & Post2. In my case I use a Dell Precision M4300 laptop which uses a NVidia Quadro FX 880M. Doing a lspci | grep VGA gave me this: 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [Quadro FX 880M] (rev a2) My workaround consists of logging in at the console and running sudo start lightdm which works perfectly but I am looking for a better workaround than this ?

  Read the article

• Ideal data structure/techniques for storing generic scheduler data in C#

  - by GraemeMiller

  I am trying to implement a generic scheduler object in C# 4 which will output a table in HTML. Basic aim is to show some object along with various attributes, and whether it was doing something in a given time period. The scheduler will output a table displaying the headers: Detail Field 1 ....N| Date1.........N I want to initialise the table with a start date and an end date to create the date range (ideally could also do other time periods e.g. hours but that isn't vital). I then want to provide a generic object which will have associated events. Where an object has events within the period I want a table cell to be marked E.g. Name Height Weight 1/1/2011 2/1/2011 3/1/20011...... 31/1/2011 Ben 5.11 75 X X X Bill 5.7 83 X X So I created scheduler with Start Date=1/1/2011 and end date 31/1/2011 I'd like to give it my person object (already sorted) and tell it which fields I want displayed (Name, Height, Weight) Each person has events which have a start date and end date. Some events will start and end outwith but they should still be shown on the relevant date etc. Ideally I'd like to have been able to provide it with say a class booking object as well. So I'm trying to keep it generic. I have seen Javasript implementations etc of similar. What would a good data structure be for this? Any thoughts on techniques I could use to make it generic. I am not great with generics so any tips appreciated.

  Read the article

• Change sysout logging level for Weblogic

  - by Justin Voss

  When I run a local copy of Weblogic, I like to see the output in the console so that I can observe my app's logging messages. But, Weblogic spits out a lot of log messages I don't care about, like these: [ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)' 08-29-2010 01:02:21 INFO Getting a JNDI connection [ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)' 08-29-2010 01:02:21 INFO Connection Returned. Elapsed time to acquire=0ms. [ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)' 08-29-2010 01:02:21 INFO Getting a JNDI connection [ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)' 08-29-2010 01:02:21 INFO Connection Returned. Elapsed time to acquire=0ms. Can I configure Weblogic to not output those? I assume that I can change the logging level to something higher than INFO and that should fix it?

  Read the article

• Ubuntu 12.04 freeze on Ctrl+ALT+F1

  - by user93800

  I have Radeon card connected over HDMI to my TV. To resolve bug with HDMI-sound, I switch between virtual terminal and GNOME desktop each time the TV is switched on with CTRL+ALT+F1 and after console appear with CTRL+ALT+F7. It's ugly, but its worked for me. Since yesterday I got system freezes on CTRL+ALT+F1 - no reaction on keyboard, mouse pointer disappear at all, GNOME desktop still displayed. Probably has nothing to do with HDMI. Any suggestion how to resolve it?

  Read the article

• Implementing Cluster Continuous Replication, Part 3

  Cluster continuous replication (CCR) uses log shipping and failover to provide a more resilient email system with faster recovery. Once it is installed, a clustered server requires different management routines. These are done either with a GUI tool, The Failover Cluster Management Console, or the Exchange Management Shell. You can use Powershell as well for some tasks. Confused? Not for long, since Brien Posey is once more here to help.

  Read the article

• JavaScript Class Patterns &ndash; In CoffeeScript

  - by Liam McLennan

  Recently I wrote about JavaScript class patterns, and in particular, my favourite class pattern that uses closure to provide encapsulation. A class to represent a person, with a name and an age, looks like this: var Person = (function() { // private variables go here var name,age; function constructor(n, a) { name = n; age = a; } constructor.prototype = { toString: function() { return name + " is " + age + " years old."; } }; return constructor; })(); var john = new Person("John Galt", 50); console.log(john.toString()); Today I have been experimenting with coding for node.js in CoffeeScript. One of the first things I wanted to do was to try and implement my class pattern in CoffeeScript and then see how it compared to CoffeeScript’s built-in class keyword. The above Person class, implemented in CoffeeScript, looks like this: # JavaScript style class using closure to provide private methods Person = (() -> [name,age] = [{},{}] constructor = (n, a) -> [name,age] = [n,a] null constructor.prototype = toString: () -> "name is #{name} age is #{age} years old" constructor )() I am satisfied with how this came out, but there are a few nasty bits. To declare the two private variables in javascript is as simple as var name,age; but in CoffeeScript I have to assign a value, hence [name,age] = [{},{}]. The other major issue occurred because of CoffeeScript’s implicit function returns. The last statement in any function is returned, so I had to add null to the end of the constructor to get it to work. The great thing about the technique just presented is that it provides encapsulation ie the name and age variables are not visible outside of the Person class. CoffeeScript classes do not provide encapsulation, but they do provide nicer syntax. The Person class using native CoffeeScript classes is: # CoffeeScript style class using the class keyword class CoffeePerson constructor: (@name, @age) -> toString: () -> "name is #{@name} age is #{@age} years old" felix = new CoffeePerson "Felix Hoenikker", 63 console.log felix.toString() So now I have a trade-off: nice syntax against encapsulation. I think I will experiment with both strategies in my project and see which works out better.

  Read the article

• Why does ganglia think my host is down?

  - by NZKoz

  I have ganglia set up to monitor our staging server, it's working great but I'm confused by the definition of 'down' to ganglia. There's a single node, running gmetad, gmond and the web frontend, but some small percentage of the time the web frontend shows some confusing output. Despite the fact that it's a single server in the cluster, and that server is the one serving the web interface, the dashboard output insists that the host is down. Then below that it has a graph which shows 50% down, 50% up. You can see an example of this here: http://i.imgur.com/MCWaS.jpg There's obviously something confusing ganglia somewhere, but I'm not sure where to start looking. Unfortunately googling for any combination of 'ganglia' 'down' 'metric name' seems return nothing but other people's ganglia installations displaying the same nonsense. Any tips on where to start looking would be greatly appreciated

  Read the article

• Recovering data from /

  - by Abhijit Gavas

  I accidentally installed Ubuntu to one of my data drives from Windows. The drive was a NTFS drive and contained about 80 GB of important data. The size of the drive is 110 GB. Its new file system is ext4. In an attempt to recover the data, I downloaded foremost and tried the following commands: foremost -i / -o /media/281C8DB01C8D7998/Recovery/ -T -v foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v (sda7 is the drive in question.) It appears that with either command, foremost gets stuck reading some file. Here is the console output: abhi@abi-PC:/dev$ foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Foremost version 1.5.7 by Jesse Kornblum, Kris Kendall, and Nick Mikus Audit File Foremost started at Fri Sep 28 20:58:00 2012 Invocation: foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Output directory: /media/281C8DB01C8D7998/Recovery_Fri_Sep_28_20_58_00_2012 Configuration file: /etc/foremost.conf Processing: stdin |------------------------------------------------------------------ File: stdin Start: Fri Sep 28 20:58:00 2012 Length: Unknown Num Name (bs=512) Size File Offset Comment Killed As you can see I have to kill it from system monitor. This approach does not seem to be working. What else could I try to recover the files? Please help. The files are very important and I will be devastated if I cannot recover them.

  Read the article

• Subterranean IL: Exception handling 1

  - by Simon Cooper

  Today, I'll be starting a look at the Structured Exception Handling mechanism within the CLR. Exception handling is quite a complicated business, and, as a result, the rules governing exception handling clauses in IL are quite strict; you need to be careful when writing exception clauses in IL. Exception handlers Exception handlers are specified using a .try clause within a method definition. .try <TryStartLabel> to <TryEndLabel> <HandlerType> handler <HandlerStartLabel> to <HandlerEndLabel> As an example, a basic try/catch block would be specified like so: TryBlockStart: // ... leave.s CatchBlockEndTryBlockEnd:CatchBlockStart: // at the start of a catch block, the exception thrown is on the stack callvirt instance string [mscorlib]System.Object::ToString() call void [mscorlib]System.Console::WriteLine(string) leave.s CatchBlockEnd CatchBlockEnd: // method code continues... .try TryBlockStart to TryBlockEnd catch [mscorlib]System.Exception handler CatchBlockStart to CatchBlockEnd There are four different types of handler that can be specified: catch <TypeToken> This is the standard exception catch clause; you specify the object type that you want to catch (for example, [mscorlib]System.ArgumentException). Any object can be thrown as an exception, although Microsoft recommend that only classes derived from System.Exception are thrown as exceptions. filter <FilterLabel> A filter block allows you to provide custom logic to determine if a handler block should be run. This functionality is exposed in VB, but not in C#. finally A finally block executes when the try block exits, regardless of whether an exception was thrown or not. fault This is similar to a finally block, but a fault block executes only if an exception was thrown. This is not exposed in VB or C#. You can specify multiple catch or filter handling blocks in each .try, but fault and finally handlers must have their own .try clause. We'll look into why this is in later posts. Scoped exception handlers The .try syntax is quite tricky to use; it requires multiple labels, and you've got to be careful to keep separate the different exception handling sections. However, starting from .NET 2, IL allows you to use scope blocks to specify exception handlers instead. Using this syntax, the example above can be written like so: .try { // ... leave.s EndSEH}catch [mscorlib]System.Exception { callvirt instance string [mscorlib]System.Object::ToString() call void [mscorlib]System.Console::WriteLine(string) leave.s EndSEH}EndSEH:// method code continues... As you can see, this is much easier to write (and read!) than a stand-alone .try clause. Next time, I'll be looking at some of the restrictions imposed by SEH on control flow, and how the C# compiler generated exception handling clauses.

  Read the article

• In Windows, a batch file with a recursive for loop and a file name including blanks

  - by uvts_cvs

  Hello, I have a folder tree, like this (it's only an example, it will be deeper in my real case): C:\test | +---folder1 | foo bar.txt | foobar.txt | +---folder2 | foo bar.txt | foobar.txt | \---folder3 foo bar.txt foobar.txt My files have one or more spaces in the name and I need to perform a command on them, so I am interested in foo bar.txt but not in foobar.txt. I tried (inside a batch file): for /r test %%f in (foo bar.txt) do if exist %%f echo %%f where the command is the simple echo. It does not work because the space is skipped and I get no output. This works but it is not what I need: for /r test %%f in (foobar.txt) do if exist %%f echo %%f It prints: C:\test\folder1\foobar.txt C:\test\folder2\foobar.txt C:\test\folder3\foobar.txt I tried using the quotation mark (") but it does not work: for /r test %%f in ("foo bar.txt") do if exist %%f echo %%f It does not work because the quotation mark is still included in the output: C:\test\folder1\"foo bar.txt" C:\test\folder2\"foo bar.txt" C:\test\folder3\"foo bar.txt"

  Read the article

• What does the fan speed sensor really report?

  - by T. Verron

  I have an overheating issue on my netbook (ASUS EeePC 1015PW), which I'm trying to troubleshoot. Using lm-sensors while overheating gave me this output : acpitz-virtual-0 Adapter: Virtual device temp1: +86.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4089 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +82.0°C (crit = +100.0°C) Core 1: +80.0°C (crit = +100.0°C) But I can't hear the fan. So I enabled manual pwm controling and set the fan to full speed, and after a few minutes I got this output : acpitz-virtual-0 Adapter: Virtual device temp1: +65.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4016 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +62.0°C (crit = +100.0°C) Core 1: +58.0°C (crit = +100.0°C) And this time I could hear the fan spinning. So there's quite obviously an issue with either fan control or fan monitoring. Hence the question : what kind of physical information does the fan sensor really report? Thank you PS. I should have added that the computer is a small, hard-to-disassemble netbook, so I can't and don't want to try experiments like "block the fan and see what the sensor reports".

  Read the article

• Resize a pendrive Linux?

  - by user11239

  I'm running Ubuntu from USB media, which has a drive capacity of 250 GB, all existing as one FAT32 partition. However, when I created the bootable Ubuntu drive, only 4.79 GB were allocated for usage. Rather than put files directly into the /cdrom where the drive is mounted, I want to expand what is listed here in aufs to be at least 200 GB. I'm hopeful that I can do this live. Output of df : Filesystem 1K-blocks Used Available Use% Mounted on aufs 4051904 4050108 0 100% / none 1542852 284 1542568 1% /dev /dev/sdb1 244076800 4901648 239175152 3% /cdrom /dev/loop0 688000 688000 0 100% /rofs none 1547840 1496 1546344 1% /dev/shm tmpfs 1547840 4828 1543012 1% /tmp none 1547840 80 1547760 1% /var/run none 1547840 0 1547840 0% /var/lock none 1547840 0 1547840 0% /lib/init/rw Output of fdisk -l : Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00083fe4 Device Boot Start End Blocks Id System /dev/sdb1 * 1 30401 244196001 c W95 FAT32 (LBA) So basically what I want to do is get /dev/sdb1 to be entirely, or almost entirely read as aufs. I'm confused over how to do this, as the file systems are all part of /dev/sdb1 on one big partition, rather than separate partitions for separate file systems.

  Read the article

• Oracle Exalogic: Simple IT Operations, Great Application Experience

  - by Michelle Kimihira

  See a demo featuring Yoav Eilat, Director of Product Marketing. Yoav demonstrates how easy it is to deploy new applications and how administrators can manage the entire system from a single console on Exalogic. Click here to view. Additional Information Product Information on Oracle.com: Oracle Fusion Middleware, Oracle Exalogic Follow us on Twitter and Facebook Subscribe to our regular Fusion Middleware Newsletter

  Read the article

• Unable to install ubuntu 12.04 beta 2 inside windows 7

  - by chetan

  When I install ubuntu 12.04 beta 2 using wubi , first it extracts the files and then asks to reboot to complete the installation. But when I reboot the machine the installation hangs and there is a message "panic occurred, switching to text console " Machine Specification Studio XPS 13 (1340) Laptop: Intel Core 2 Duo P8600 (3MB cache/2.4GHz/1066Mhz FSB) Chipset : NVIDIA® MCP79MX Please contact at [email protected] if any more information needed .

  Read the article

• No Wireless In Ubuntu 13.10

  - by viktorhubinette

  When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• postfix configuration

  - by kibs

  failed to start the postfix service output given was postfix: fatal: config variable inet_interfaces: host not found: all

  Read the article

• Combining Shared Secret and Certificates

  - by Michael Stephenson

  As discussed in the introduction article this walkthrough will explain how you can implement WCF security with the Windows Azure Service Bus to ensure that you can protect your endpoint in the cloud with a shared secret but also combine this with certificates so that you can identify the sender of the message.   Prerequisites As in the previous article before going into the walk through I want to explain a few assumptions about the scenario we are implementing but to keep the article shorter I am not going to walk through all of the steps in how to setup some of this. In the solution we have a simple console application which will represent the client application. There is also the services WCF application which contains the WCF service we will expose via the Windows Azure Service Bus. The WCF Service application in this example was hosted in IIS 7 on Windows 2008 R2 with AppFabric Server installed and configured to auto-start the WCF listening services. I am not going to go through significant detail around the IIS setup because it should not matter in relation to this article however if you want to understand more about how to configure WCF and IIS for such a scenario please refer to the following paper which goes into a lot of detail about how to configure this. The link is: http://tinyurl.com/8s5nwrz   Setting up the Certificates To keep the post and sample simple I am going to use the local computer store for all certificates but this bit is really just the same as setting up certificates for an example where you are using WCF without using Windows Azure Service Bus. In the sample I have included two batch files which you can use to create the sample certificates or remove them. Basically you will end up with: A certificate called PocServerCert in the personal store for the local computer which will be used by the WCF Service component A certificate called PocClientCert in the personal store for the local computer which will be used by the client application A root certificate in the Root store called PocRootCA with its associated revocation list which is the root from which the client and server certificates were created   For the sample Im just using development certificates like you would normally, and you can see exactly how these are configured and placed in the stores from the batch files in the solution using makecert and certmgr.   The Service Component To begin with let's look at the service component and how it can be configured to listen to the service bus using a shared secret but to also accept a username token from the client. In the sample the service component is called Acme.Azure.ServiceBus.Poc.Cert.Services. It has a single service which is the Visual Studio template for a WCF service when you add a new WCF Service Application so we have a service called Service1 with its Echo method. Nothing special so far!.... The next step is to look at the web.config file to see how we have configured the WCF service. In the services section of the WCF configuration you can see I have created my service and I have created a local endpoint which I simply used to do a little bit of diagnostics and to check it was working, but more importantly there is the Windows Azure endpoint which is using the ws2007HttpRelayBinding (note that this should also work just the same if your using netTcpRelayBinding). The key points to note on the above picture are the service behavior called MyServiceBehaviour and the service bus endpoints behavior called MyEndpointBehaviour. We will go into these in more detail later.   The Relay Binding The relay binding for the service has been configured to use the TransportWithMessageCredential security mode. This is the important bit where the transport security really relates to the interaction between the service and listening to the Azure Service Bus and the message credential is where we will use our certificate like we have specified in the message/clientCrentialType attribute. Note also that we have left the relayClientAuthenticationType set to RelayAccessToken. This means that authentication will be made against ACS for accessing the service bus and messages will not be accepted from any sender who has not been authenticated by ACS.   The Endpoint Behaviour In the below picture you can see the endpoint behavior which is configured to use the shared secret client credential for accessing the service bus and also for diagnostic purposes I have included the service registry element.     Hopefully if you are familiar with using Windows Azure Service Bus relay feature the above is very familiar to you and this is a very common setup for this section. There is nothing specific to the username token implementation here. The Service Behaviour Now we come to the bit with most of the certificate stuff in it. When you configure the service behavior I have included the serviceCredentials element and then setup to use the clientCertificate check and also specifying the serviceCertificate with information on how to find the servers certificate in the store.     I have also added a serviceAuthorization section where I will implement my own authorization component to perform additional security checks after the service has validated that the message was signed with a good certificate. I also have the same serviceSecurityAudit configuration to log access to my service. My Authorization Manager The below picture shows you implementation of my authorization manager. WCF will eventually hand off the message to my authorization component before it calls the service code. This is where I can perform some logic to check if the identity is allowed to access resources. In this case I am simple rejecting messages from anyone except the PocClientCertificate.     The Client Now let's take a look at the client side of this solution and how we can configure the client to authenticate against ACS but also send a certificate over to the service component so it can implement additional security checks on-premise. I have a console application and in the program class I want to use the proxy generated with Add Service Reference to send a message via the Azure Service Bus. You can see in my WCF client configuration below I have setup my details for the azure service bus url and am using the ws2007HttpRelayBinding.   Next is my configuration for the relay binding. You can see below I have configured security to use TransportWithMessageCredential so we will flow the token from a certificate with the message and also the RelayAccessToken relayClientAuthenticationType which means the component will validate against ACS before being allowed to access the relay endpoint to send a message.     After the binding we need to configure the endpoint behavior like in the below picture. This contains the normal transportClientEndpointBehaviour to setup the ACS shared secret configuration but we have also configured the clientCertificate to look for the PocClientCert.     Finally below we have the code of the client in the console application which will call the service bus. You can see that we have created our proxy and then made a normal call to a WCF in exactly the normal way but the configuration will jump in and ensure that a token is passed representing the client certificate.     Conclusion As you can see from the above walkthrough it is not too difficult to configure a service to use both a shared secret and certificate based token at the same time. This gives you the power and protection offered by the access control service in the cloud but also the ability to flow additional tokens to the on-premise component for additional security features to be implemented. Sample The sample used in this post is available at the following location: https://s3.amazonaws.com/CSCBlogSamples/Acme.Azure.ServiceBus.Poc.Cert.zip

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• Does Altova StyleVision support generation of these specific Word XML Word ML List Numbering Bullet Markup? Extend with custom external XSLT?

  - by Alex S

  Does Altova StyleVision support generation of these specific Word XML Word ML List Numbering Bullet Markup? Extend with custom external XSLT? PS: I know is specific to Altova and their Dev Tools, but just like Eclipse and Visual Studio it is one of the widest used toolkits for XML related development & programming. So, please do not hate, ban or give negative. Linked below is a section of information for Word ML XML and its numbering, list, bullet etc. The markup is pretty extensive. I am wondering if this can be replicated via StyleVision or is this a limitation that needs to extended with an external XSLT? Quote: Key links to the Markup Documentation: http://officeopenxml.com/WPnumbering.php http://officeopenxml.com/WPnumberingAbstractNum.php Also: /WPnumberingLvl.php Short outline of the Documentation there: *Numbering, Levels and Lists* - Overview - Defining a Numbering Scheme - Defining a Particular Level ++ Numbering Level Text ++ Numbering Format ++ Displaying as Numerals Only ++ Restart Numbering ++ Picture or Image as Numbering Symbol ++ Justification ++ Overriding a Numbering Definition If StyleVision supports the above, where and how inside StyleVision can I access or use these properties/ attributes for the markup? From what I've gathered, I think it does not. In the past, I have written XSL-FO and XSL-WordML by hand. So I could write an add-on external XSLT containing Word specific markup for this purpose. *Given the limitation exists, the questions now: * Where and how do I create and linked inside of StyleVision so as to APPLY and EXTEND these capability limitations of StyleVision. AND How could I make it apply only for Word ML / Word XML output styling and be DEACTIVATED/ DISABLED for HTML and PDF output?

  Read the article

• Gnome shell not starting at login, but can start from terminal (Ubuntu 12.04)

  - by Mat Leonard

  I upgraded to Ubuntu 12.04 recently and for some reason it broke Gnome 3. The shell doesn't start up at login. My .xsession-errors looks like this right after I log in: gnome-session[1689]: WARNING: Session 'gnome' runnable check failed: Timed out (gnome-settings-daemon:1744): color-plugin-WARNING **: failed to get edid: unable to get EDID for output (gnome-settings-daemon:1744): color-plugin-WARNING **: unable to get EDID for xrandr-default: unable to get EDID for output (gnome-settings-daemon:1744): color-plugin-WARNING **: failed to reset xrandr-default gamma tables: gamma size is zero ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ** Message: moving back from GtkStatusIcon to indicator Then I can run gnome-shell --replace, the shell starts up and everything works. This is what I get immediately after: Window manager warning: Log level 16: Unable to register authentication agent: GDBus.Error:org.freedesktop.PolicyKit1.Error.Failed: An authentication agent already exists for the given subject Window manager warning: Log level 16: Error registering polkit authentication agent: GDBus.Error:org.freedesktop.PolicyKit1.Error.Failed: An authentication agent already exists for the given subject (polkit-error-quark 0) (gnome-shell:2442): folks-WARNING **: Failed to find primary PersonaStore with type ID 'eds' and ID 'system'. Individuals will not be linked properly and creating new links between Personas will not work. The configured primary PersonaStore's backend may not be installed. If you are unsure, check with your distribution Also, if I run /usr/lib/nux/unity_support_test -p, everything comes back as Yes and this checks out: OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce 8300 GS/PCIe/SSE2 OpenGL version string: 3.3.0 NVIDIA 295.40 It isn't a huge problem since I can get gnome shell to work, but it is a little annoying. So, I'd like to fix this. Thanks for your help.

  Read the article

• Using Terminal Services 'query' in batch file

  - by dboarman-FissureStudios

  I have a batch file that checks several of our servers for a user. From the command: query user %userID% /server:ServerName I want to capture the output before it goes to the screen. Is there a way to redirect the output to a variable? The basic gist of what I want to accomplish is this - we iterate through our servers: query user %userID% /server:Server1 query user %userID% /server:Server2 query user %userID% /server:Server3 query user %userID% /server:Server4 Instead of outputting a message that the user could not be found on a specific server, I would like for it to only notify me if it finds the user on a server.

  Read the article

• Everything "invisible" when launching map from launcher

  - by Predanoob

  Excuse my noobiness, but I downloaded the SDK, and I tried the map Forest from within the editor and it worked fine. However if I launch it from the Launcher using the console it looks like this: http://i.stack.imgur.com/U7rPU.jpg I can use the weapons(although they are invisible), and interact with objects despite not seeing them. I also did my own map same problem. What am I doing wrong? ?(

  Read the article

• Recording slow web stream

  - by Budric

  I'm trying to record an mpeg2 video stream from a website that doesn't have the greatest bandwidth. The video often buffers. I want to download the stream and watch it offline. The extract stream format received is: Stream #0.0[0x44]: Audio: mp2, 48000 Hz, stereo, s16, 192 kb/s Stream #0.1[0x45]: Video: mpeg2video (Main), yuv420p, 704x576 [PAR 16:11 DAR 16:9], 15000 kb/s, 27.19 fps, 25 tbr, 90k tbn, 50 tbc I use the following tool to transocde the stream: ffmpeg -i "http://url" -y -vcodec libx264 -b 3000k -acodec copy /tmp/stream.mp4 Unfortunately after a few seconds ffmpeg stops recording with an error [mpegts @ 0x1f0b9c0] PES packet size mismatch [mp2 @ 0x1f14640] incomplete frame Error while decoding stream #0.0 [mpeg2video @ 0x1f16860] ac-tex damaged at 0 26 [mpeg2video @ 0x1f16860] Warning MVs not available I've tried encoding with vlc as well with similar issues. Although vlc doesn't stop encoding, the output video has regions where it hangs. vlc -I dummy "http://url" --network-caching="1000" --sout="#transcode{vcodec=h264,vb=3000,acodec=mp3,ab=192}:std{access=file,mux=mp4,dst=/tmp/stream.mp4}" [mpeg2video @ 0x7f2d4c001e20] ac-tex damaged at 9 33 [mpeg2video @ 0x7f2d4c001e20] Warning MVs not available [mpeg2video @ 0x7f2d4c001e20] concealing 132 DC, 132 AC, 132 MV errors [mpeg2video @ 0x7f2d4c001e20] ac-tex damaged at 16 17 [mpeg2video @ 0x7f2d4c001e20] Warning MVs not available [mpeg2video @ 0x7f2d4c001e20] concealing 836 DC, 836 AC, 836 MV errors libdvbpsi error (PSI decoder): TS discontinuity (received 4, expected 3) for PID 0 I also tried flv transcoding and it shows up with its own set of issues, like output flv file hangs in certain parts. Anyone know what's wrong or how to fix this?

  Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >