Search Results

Search found 8483 results on 340 pages for 'magnet links'.

Page 265/340 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

  • Cisco ASA Site-to-Site VPN Dropping

    - by ScottAdair
    I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

    Read the article

  • How do I redirect my website from non-www to WWW using Apache2?

    - by Andrew
    I'm currently trying to set up my personal webpage. I am using a VPS and have manually installed Wordpress, and everything seems to work... except if I go to the non-www version of my website, it comes up with a page not found. www.andrewrockefeller.com <-- Works andrewrockefeller.com <-- Does not (and I want to redirect it to www.andrewrockefeller.com) I have tried adding RewriteEngine functionality to my .htaccess, and that isn't working. I have also tried adding the 'most-voted' method of adding to my default file (which apache2.conf pulls from: <VirtualHost *> ServerName andrewrockefeller.com Redirect 301 / http://www.andrewrockefeller.com/ </VirtualHost> Seeing how many people are able to get the above working, is there something else I may be missing to allow that to function? Thank you for your time! EDIT: My .htaccess file is as follows: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress The #Wordpress section was autocreated when I changed the settings from ?p=1 (ugly links) to prettylinks. Any proposed solutions I've found on here I've tried out and restarted apache2, and it hasn't worked.

    Read the article

  • open source solution to a gateway for a network of a housing cooperative of 150 people

    - by SirDinosaur
    i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

    Read the article

  • How to link to a subfolder of a share?

    - by Nicolas Raoul
    On my Windows XP server, a folder called Share2 is shared. It contains a subfolder called folder3. The guest account is protected by a password, which means network users have to type the guest password to access it. When a user types \\server\Share2 in his file explorer, he is prompted for a password. When a user types \\server\Share2\folder3 in his file explorer, an error appears. He is not even prompted for a password. This is problematic because I want to link to this particular folder. How can I link to folder3? Notes: - Both Desktop shortcuts and HTML links in IE7/8 give an error if I link to folder3, but work if I just link to Share2. - Using the file:// syntax instead of the \\ syntax leads to the same results. - Password setting per http://www.lancelhoff.com/how-to-password-protect-a-shared-folder - Not using "Simple File Sharing" - The error message is ???????????????????????? which means "could not find it. check the path and try again". No English Windows around to try, sorry! It is easy to reproduce the problem though, so can anyone post the English error message for the sake of searchability? Thanks!

    Read the article

  • Yum Error Installing Git from kernel.org Repo

    - by Lance
    I want to install the latest version of Git using yum and the RPM repository on kernel.org, but adding the repo to yum.repos.d causes yum to fail with checksum errors. The prevailing solution to this issue seems to be to simply use the repository at Webtatic as answered here on superuser. I know I can also install an older version of Git using the EPEL repo, or compile from the latest source tarball, but honestly I want to understand why I'm having issues using the kernel.org repo. Here’s the workflow, after a clean install of CentOS 5.5 and "yum update": [root]# wget -P /etc/yum.repos.d/ http://kernel.org/pub/software/scm/git/RPMS/git.repo [root]# yum clean all [root]# yum repolist Loaded plugins: fastestmirror Determining fastest mirrors * addons: mirrors.netdna.com * base: mirror.clarkson.edu * epel: serverbeach1.fedoraproject.org * extras: centos.mirror.nac.net * updates: mirror.cogentco.com addons | 951 B 00:00 addons/primary | 202 B 00:00 base | 2.1 kB 00:00 base/primary_db | 1.6 MB 00:01 epel | 3.7 kB 00:00 epel/primary_db | 2.8 MB 00:01 extras | 2.1 kB 00:00 extras/primary_db | 188 kB 00:00 git | 1.2 kB 00:00 git/primary | 155 kB 00:00 http://www.kernel.org/pub/software/scm/git/RPMS/i386/repodata/primary.xml.gz: [Errno -3] Error performing checksum Trying other mirror. git/primary | 155 kB 00:00 http://www.kernel.org/pub/software/scm/git/RPMS/i386/repodata/primary.xml.gz: [Errno -3] Error performing checksum Trying other mirror. Error: failure: repodata/primary.xml.gz from git: [Errno 256] No more mirrors to try. Any suggestions as to a solution, or details why the kernel.org repo has this issue? (Sorry I can't include more links to my references, but I don't have the reputation for that yet.)

    Read the article

  • Exchange 2010 DAG + VMWare HA = no support?

    - by Dan
    We currently have an Exchange 2003 clustered environment (two machine cluster) that we're looking to upgrade to 2010. We recently purchased a VMWare virtualization environment (three Dell R710's with an EMC NS-120 serving up NFS datastores - iSCSI is available) that we wish to use for this new environment. I'm seeing that Microsoft does not support Exchange 2010 DAGs with a virtualization high availability solution (see links below). I would like to utilize the DAG to ensure the data stays available if one host goes down, and HA to ensure that if the physical host goes down, the VM will come back up on the other available host. Does anybody know why MS does not support this? VMWare HA will only restart the VM if it is hung/down - I don't see any difference between this and restarting the physical box if someone pulled the power... Will we only run into issues with support if it has something to do with HA/DAG failover or will they see we have HA and tell us to put it on a physical box even if it has nothing to do with HA? If we disable HA for these VM's will that satisfy them on a support case? Has anybody set up an Exchange 2010 DAG on VMware with HA enabled? Will they have any issues with using an NFS datastore? We have much greater flexibility on the EMC with NFS vs iSCSI, so I would prefer to continue utilizing that. Thanks for any input! http://www.vmwareinfo.com/2010/01/verifying-microsoft-exchange-2010.html Take a look at the second image under "Not Supported" http://technet.microsoft.com/en-us/library/aa996719.aspx "Microsoft doesn't support combining Exchange high availability solutions (database availability groups (DAGs)) with hypervisor-based clustering, high availability, or migration solutions. DAGs are supported in hardware virtualization environments provided that the virtualization environment doesn't employ clustered root servers."

    Read the article

  • How to get german QWERTY on Windows?

    - by Arturas M
    Well I'm used to having the world standard keyboard which is qwerty and not qwertz... But on windows I can't find the choice for german input which would be qwerty, not qwertz. In linux there was german input with qwerty so it was fun. I believe it should be on Windows too? Cause i'm sick of this qwertz always having to correct and search for z or y... Yeah, I know, if Germans made a mistake, it wasn't loosing WW2... Edit: Maybe I wasn't clear enough, it's not about changing between different language inputs? It's about having all german keys in german input, just the z and y would be in the correct places like all the worlds keyboards use and like the US keyboard uses... Solution: Well unfortunately by searching everywhere and waiting for answers I couldn't find what I needed, so I came up with this solution - I used The The Microsoft Keyboard Layout Creator And created my own very custom layout by modifying the default german layout and switching places of z and y. In case somebody needs it and doesn't want to go the hard way, I decided to upload them, so here are the links to download and install the keyboard layout: http://www20.zippyshare.com/v/95071447/file.html http://rapidshare.com/files/3822150342/German%20QWERTY%202%20by%20Arturas%20M.zip It will appear as a choice under German input between languages in your language bar. If you just want to use this german layout, just remove all german layouts and install this one. Good luck and have fun using it!

    Read the article

  • How to disable irritating Office File Validation security alert?

    - by Rabarberski
    I have Microsoft Office 2007 running on Windows 7. Yesterday I updated Office to the latest service pack, i.e. SP3. This morning, when opening an MS Word document (.doc format, and a document I created myself some months ago) I was greeted with a new dialog box saying: Security Alert - Office File Validation WARNING: Office File Validation detected a problem while trying to open this file. Opening this is probably dangerous, and may allow a malicious user to take over your computer. Contact the sender and ask them to re-save and re-send the file. For more security, verify in person or via the phone that they sent the file. Including two links to some microsoft blabla webpage. Obviously the document is safe as I created it myself some months ago. How to disable this irritating dialog box? (On a sidenote, a rethorical question: Will Microsoft never learn? I consider myself a power user in Word, but I have no clue what could be wrong with my document so that it is considered dangerous. Let alone more basic users of Word. Sigh....)

    Read the article

  • Installing Windows 7 from USB on a Thinkpad T61

    - by Halik
    I am trying to install Windows 7 Professional from USB 3.0 flashdrive, on a Thinkpad T61. The problem is, Thinkpads BIOS will not detect the flash drive as bootable medium, and won't allow to boot from it. What I did: Enabled USB BIOS Support in BIOS (it was on by default) In startup menu, added USB HDD to boot order (it has '-' sign in front of it) Created Windows 7 install media with UNetbootin, WinUSB (linux tool) dd and Grub4DOS. As you can tell, currently, I only have access to Linux machine to make the flashdrive. What happens: The T61 BIOS shows '-USB HDD' in boot order menu. The '-' sign suggests that the plugged flash drive is currently not bootable. The same flashdrive (with the same Windows image on it) is booting without any problems on a Dell D430 and Lenovo Y550. Also, Ubuntu 12.04 install USB created with Unetbootin shows as bootable ('+' sign in BIOS boot order menu) and boots from the F12 boot menu. Additional info thinkwiki.org says that some Thinkpad BIOSes do not use MBR on flashdrives. It suggests using Extended-IPL boot loader, but the provided links are broken and there seems to be no mirrors. Solution: http://superuser.com/a/430186/54970

    Read the article

  • OpenSolaris livecd, NForce NIC driver, and NTFS USB mounting. Oh My!

    - by Jake Wharton
    I'm attempting to install OpenSolaris 2009.06 on my server. Before I do I would like to test that everything works and am running in to problems. It has an Abit AN-M2 motherboard with an NForce chipset. The driver config utility says that I need a third-party driver and links me to http://homepage2.nifty.com/mrym3/taiyodo/eng/. Scrolling to the bottom, I have downloaded both tgzs just in case. Now the fun part: The only way to get this on to the computer is via a USB drive since I can't access the network. Also, install CD in the drive otherwise I'd just burn them to DVD. Since my USB key is NTFS formatted I cannot mount it since the install CD seems to be lacking NTFS drivers which require more downloaded packages. What should I do? The server will simply be a dumb NAS and I know that there exists other OpenSolaris-based flavors such as Nexenta but from what I read the stock install is likely the best. If this is not the case and pursuing a different flavor is required or better I will also accept that as an answer (but please don't jump straight to it).

    Read the article

  • Yum Error Installing Git from kernel.org Repo

    - by Lance
    I want to install the latest version of Git using yum and the RPM repository on kernel.org, but adding the repo to yum.repos.d causes yum to fail with checksum errors. The prevailing solution to this issue seems to be to simply use the repository at Webtatic as answered here on superuser. I know I can also install an older version of Git using the EPEL repo, or compile from the latest source tarball, but honestly I want to understand why I'm having issues using the kernel.org repo. Here’s the workflow, after a clean install of CentOS 5.5 and "yum update": [root]# wget -P /etc/yum.repos.d/ http://kernel.org/pub/software/scm/git/RPMS/git.repo [root]# yum clean all [root]# yum repolist Loaded plugins: fastestmirror Determining fastest mirrors * addons: mirrors.netdna.com * base: mirror.clarkson.edu * epel: serverbeach1.fedoraproject.org * extras: centos.mirror.nac.net * updates: mirror.cogentco.com addons | 951 B 00:00 addons/primary | 202 B 00:00 base | 2.1 kB 00:00 base/primary_db | 1.6 MB 00:01 epel | 3.7 kB 00:00 epel/primary_db | 2.8 MB 00:01 extras | 2.1 kB 00:00 extras/primary_db | 188 kB 00:00 git | 1.2 kB 00:00 git/primary | 155 kB 00:00 http://www.kernel.org/pub/software/scm/git/RPMS/i386/repodata/primary.xml.gz: [Errno -3] Error performing checksum Trying other mirror. git/primary | 155 kB 00:00 http://www.kernel.org/pub/software/scm/git/RPMS/i386/repodata/primary.xml.gz: [Errno -3] Error performing checksum Trying other mirror. Error: failure: repodata/primary.xml.gz from git: [Errno 256] No more mirrors to try. Any suggestions as to a solution, or details why the kernel.org repo has this issue? (Sorry I can't include more links to my references, but I don't have the reputation for that yet.)

    Read the article

  • Facing application redirection issue on nginx+tomcat

    - by Sunny Thakur
    I am facing a strange issue on application which is deployed on tomcat and nginx is using in front of tomcat to access the application from browser. The issue is, i deployed the application on tomcat and now setup the virtual host on nginx under conf.d directory [File i created is virtual.conf] and below is the content i am using for the same. server { listen 81; server_name domain.com; error_log /var/log/nginx/domain-admin-error.log; location / { proxy_pass http://localhost:100; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } Now the issue is this when i am using rewrite ^(.*) http://$server_name$1 permanent; in server section and access the URL then this redirects to https://domain.com and i am able to log in to app and able to access the links also [I am not using ssl redirection in this host file and i don't know why this is happening] Now when i removed this from server section then i am able to access the application from :81 and able to logged into the application but when i click on any link in app this redirect me to the login page. I am not getting any logs in application logs as well as tomcat logs. Please help on this if this is a redirection issue of nginx. Thanks, Sunny

    Read the article

  • How private is the Opera Turbo feature of Opera?

    - by Marcus V
    If I'm using Opera with the Opera Turbo feature turned on (always, not set to "automaticly"). Can anyone see what sites I'm visiting (except Opera of course ...)? Opera Turbo uses a proxy server, so it should be that way, but as a not very technical person I'm not sure. Why do I want this? Well: nowadays, at least in my country, more and more (legal) open Wi-Fi connections are available. In those environments I like to have more privacy protections. I don't mind if they can see my IP address, but I just want to hide as much as I can of what I am doing. BTW: I don't care that they can see the data transferred; it doesn't have to be that secret. I only want to hide the requested Internet site links. BTW: I know that Opera Turbo only works with non-secure websites (HTTP), but that's fine for me. I only want it to work with these sites. BTW: I'm not need this for illegal purposes; I only want this for privacy reasons.

    Read the article

  • Connecting jconsole using SOCKS to Amazon EC2

    - by freshfunk
    I'm trying to use jconsole to view stats on an EC2 instance by using a socks proxy created by SSH. I've tried the various scripts mentioned in the links below but to no avail: http://simplygenius.com/2010/08/jconsole-via-socks-ssh-tunnel.html http://gabrielcain.com/blog/2010/11/02/using-ssh-proxying-to-connect-jconsole-to-remote-cassandra-instances/ I'm running ssh -f -ND 8123 myuser@mymachine and verified that at least Firefox goes through it as a proxy. I then run jconsole -J-DsocksProxyHost=localhost -J-DsocksProxyPort=8123 service:jmx:rmi:///jndi/rmi://ec2-XX-XX-XXX-XXX.compute-1.amazonaws.com:8080/jmxrmi I run netstat -n on my EC2 instance and I see a connection created by my machine. However, the connection eventually disappears and I get a 'channel 2: open failed: connect failed: Operation timed out' from my ssh tunnel. I've opened the jmx port through the security group and I've checked the port on the EC2 instance to make sure it's open (by telnet-ing to it). I'm not sure where to look next. Are there some properties in sshd_config or ssh_config I need to enable for tunneling? Or anything in Mac OS X? I feel like a serious noob but sys administration is really not my strong point. I've spent several hours and can't get this to work.

    Read the article

  • Is there a program to show programs loading during the boot process in real time?

    - by Gary M. Mugford
    Hi all, There are any number of programs that will show me WHAT will run during the boot process for Windows XP. I've always been partial to Mike Lin's version but there are several others, some of which are quite possibly superior. That's not the issue. What I'd really like is a program that would load first and then would list the programs that were about to load and then check them off as the programs loaded. This isn't something I necessarily need for myself. But certain family members get click happy as soon as they see the icon they eventually want to run and end up clicking on it. THIRTY TWO TIMES in one memorable crash-inducing spasm. If there was some way for 'progress' to be shown during the loading of from the various spots Windows auto-loads from, PLUS a BIG BANNER saying "Please do not move the mouse or click on anything until done.", I think I might cut down on my early morning family support calls significantly. I've tried a variety of searches, but I couldn't find the ones that show in real time in the forest of links to programs that will show the list after the fact. Any leads? If not, do any of you who write the after-the-fact listers want to take a shot at producing a utility to do what I think would be a relatively popular utility? Best of the season to all of you and yours. Thanks in advance for any replies, GM

    Read the article

  • Copy a website and preserve the file & folder structure

    - by DrStalker
    I have an old web site running on an ancient version of Oracle Portal that we need to convert to a flat-html structure. Due to damage to the server we are not able to access the administrative interface, and even if we could there is no export functionality that can work with modern software versions. It would be enough to crawl the website and have all the pages & images saved to a folder, but the file structure needs to be preserved; that is, if a page is located at http://www.oldserver.com/foo/bar/baz/mypage.html then it needs to be saved to /foo/bar/baz/mypage.html so that the various Javascript bits will continue to function. None of the web crawlers I've found have been able to do this; they all want to rename the pages (page01.html, page02.html etc) and break the folder structure. Is there any crawler out there that will recreate the site structure as it appears to a user accessing the site? It doesn't need to redo any of teh content of the pages; once rehosted the pages will all have the same names they did originally so links will continue to work.

    Read the article

  • 9000+ different subdomains 301 to main domain, .htacess apache

    - by Karim
    I bought a domain that had various subdomains such as Kim.domain.com/whatever john.domain.com/whatever1 Lizo.domain.com/whatever2 Simon.domain.com/whatever1 And this was in the thousands, and also had links to these pages I'd like to do a 301 redirect for all these urls into http://domain.com Any idea how this could be done? This is for a apache web server and needs to be done via .htaccess I have implemented the solution from reading the answer below. RewriteEngine On RewriteCond %{HTTP_HOST} !^www. domain.com$ RewriteCond %{HTTP_HOST} !^$ RewriteRule ^/(.*)$ http:/ / www. domain.com/$1 [L,R=301] However I have a slight problem, I would like to redirect all subdomains + subfolders to http://www. domain.com/ With the exception of http: //domain. com/subfolder/, in which case I would like to redirect to http: // www.domain. com/subfolder/ [i.e. exception for no subdomain] I'm guessing I need to add an exception, what can I do to implement this. Note: example URLs above have had spaces added to them to prevent spam blocks for blocking the post.

    Read the article

  • I receive email not addressed to me - virus?

    - by Anne
    Every once in a while I receive email (on Gmail) that isn't addressed to me. Gmail puts it in the spam box, because it 'can't verify that it has been sent by [sender]'. The emails, when opened, contain confidential information about deliveries and paid bills (it does look an awful lot like 'real' mail from well-known companies, and it doesn't look like a scam, since the mail is informative - they give information instead of asking for credit card numbers ;-)), and I even got an email from "Facebook" that I requested a password change and that I have to 'click here' to change the password for [email address that isn't mine]. I am not the only addressee, there seems to be a whole list of Gmail addresses beginning with 'a'. The original addressee obviously has some sort of virus, and now I wonder if this could be a risk for me too. Is my email being sent around without my knowing too? I am not the kind of person who randomly clicks on shady links - I am very careful on the internet - but maybe there are other ways of catching viruses? Is there something I should do/check? Thank you for your help!

    Read the article

  • Connection refused in ssh tunnel to apache forward proxy setup

    - by arkascha
    I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

    Read the article

  • 2010 cgi script failure

    - by Barry F
    Hi. I hope you can help, I'm just a beginner! I have listed a few extra details which may not be relevant. I upload cgi scripts onto local/personal directory on a Apache/2.2.10 server, using FTP95Pro in ASCII. The scripts execute correctly using perl on my web-server in a terminal session. Thus my code has no fatal syntax errors. Webpages 'action' each cgi script at /cgi-bin/. There are symbolic links which link system directory files to my local directory files. FollowSymLinks is enabled (unsure how). Permissions are correct (755). This set-up hasnt changed, apparently. The scripts have excuted perfectly for years, up to 2010. But now, in 2010, I have replaced working scripts with new script/files, now with exactly the same text, filename and permissions. Only the date (last modified) has changed. But now I receive a 500 Internal Server Error, and cannot determine why. My server administator assumes I have code errors. But code is unchanged since last year, and it runs fine (albeit no arguments) on web-server console using perl myscript.cgi Is there anything you can think of which may have changed ? I'm suspicious of the new decade. I think the server swapped from Linux to Windows OS last year, but my server administrator got it all working OK. Is there something unusual he may have missed, related to 2010 ? Thank you in advance

    Read the article

  • Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

    - by fastreload
    I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

    Read the article

  • Can't write to samba share

    - by Tiddo
    I try to setup a samba file server, but whatever I do I can't get write access to work (reading works fine). This is my current situation: I have a local fileserver with 3 harddisks mounted at /mnt/share/disk<nr>. 2 of these use the ext4 filesystem, the third one is ntfs. This file server runs Fedora 18 32-bit. The root folders of these harddisks are owned by superman:superman, and testparm outputs the following: [global] workgroup = WORKGROUP netbios name = FILE_SERVER server string = Samba Server Version %v interfaces = lo, eth0, 192.168.123.191/8 log file = /var/log/samba/log.%m max log size = 50 unix extensions = No load printers = No idmap config * : backend = tdb hosts allow = 192.168.123. cups options = raw wide links = Yes [share] comment = Home Directories path = /home/share/ write list = superman, @users force user = superman read only = No create mask = 0777 directory mask = 0777 inherit permissions = Yes guest ok = Yes I've tried a lot to get this to work: the disk are chmodded to 777, I've tried turning off selinux, I've added the samba_share_t label to the disks and as can be seen in the above output I tried to make the smb config as permissive as I could, but still I cannot write to the share (tried from Windows 7 and another Fedora installation). What can I try to be able to write to the shares? EDIT: The replies I got so far are mostly concerned with the smb.conf. I have however tried a lot of different setup, ready made configs, and solutions to similar problems for the smb.conf file, so I suspect that the real problem is somewhere else.

    Read the article

  • HyperV - low CPU usage

    - by Klark
    I am very new to HyperV and virtual machine philosophy in general, so please expect more or less nooby questions :) I have a server that is only used as a host for virtual machines. OS is windows server 2008 R2 and it is running on 16 CPU and 48 GBs of RAM. On aforementioned server there are 8 VMs, each having 4 CPUs and 4 GBs of RAM. On those VMs we are running some CPU intensive tasks. Each machine has nearly 100% cpu usage. After I noticed slow performance I went to the host machine and started playing with process explorer. It turned out that cpu usage is very low. Also I/O is very low, and of course, memory consumption is high, which is expected. Of course, I don't expect that those 4 virtual cores dedicated to a VM work as fast as real, hardware 4 cores, but still I expected a higher consumption of real hardware. Is this sort of behaviour normal? I see that the most of CPU usage on host machine are marked as interrupts (which I guess is normal) and all those interrupts are passed to only one core (which is strange). Are there out of box optimization that I could perform to finally use all that processing power that is under the hood. My knowledge of virtualization technology is near to embarrassing, so I would be grateful for any links that could enlightened me :) Thanks.

    Read the article

  • What is the ideal way to set up multiple FTP enabled web accounts on Fedora?

    - by Nicholas Flynt
    I'm setting up a test server for use as a web development platform, and I'd like to mimic as closely as I can a typical shared hosting setup. That is, I'd like my server to have multple user FTP accounts, each of which links to a directory containing the webroot of the site, and I'd like apache to be able to easily see and manupulate these files. I'll admit: I'm not as familiar with Fedora as I'd like, I run Ubuntu on my home box and SElinux is giving me some grief. My initial plan was to have each user FTP into their home directory, and put the web directory there as well, but SElinux throws a hissy fit when apache tries to access anything outside of its web directory, so that plan was a no go. Would it be wise to continue this route, and perhaps mount web directories in user home folders so that FTP could still be used to access them, even though apache saw them in var/www like it expects? Would it make more sense to set up custom FTP accounts and use a single FTP user on the server box? What's the general course of action on something like this? I'm using vsftpd right now to host web directories, which is why I'm liking the home directory approach (it's simple and secure) but of course there's bound to be a better way to go about it. Thanks. (I'll leave other things, like restricted DB access and such, to another post. I'm interested right now with just getting FTP and apache to play nice in a multi-user environment.) PS: For the record, an issue I ran into when doing all of this was that if apache isn't running as the same user as the FTP account is saving as, there are permissions errors when FTP creates files, requiring the remote user to chmod the files to fix it. A logical fix would be to run apache in a special group, put all web users in this group, and have FTP access default to giving this group read/write access to everything like apache would expect, but I never could figure out how to accomplish this. Bonus points and cake if you know a solution.

    Read the article

  • What is auto-mounting my media volume?

    - by user285277
    Something is repeatedly mounting my "media" share, doing something with it, then quietly un-mounting it with no notifications at the user level. from the little I can gleaned from the console messages below, I thought I'd managed to stop it, if not understand it last night when I followed instructions for deleting all traces of the Google Update Daemon. I've not been using any Google apps whatsoever, so I was surprised to see that in Console. What's more surprising, and perhaps a little distressing, is that the same thing occurred this evening, when the Google Daemon is long gone. I don't have that log because I can't recall precisely what time it occurred. I'll do a search and provide it if you wish, though. In the meantime, any help with this would be extremely appreciated. I've asked over at Apple Discussions but I think it might be a little deeper than those manning the boards this weekend are comfortable with. It's certainly beyond my meager skills. With apologies in advance if this is more lines thank you need. Please note that I've transformed the Google links a little because the forum here requires more reputation points before one can post more than two links. 12/27/13 10:47:31.000 PM kernel[0]: memorystatus_thread: idle exiting pid 53629 [distnoted] 12/27/13 10:48:10.433 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 0; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.434 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 1; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.950 PM com.apple.SecurityServer[17]: Session 103257 created 12/27/13 10:48:34.328 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 2; not stale; error: The file doesn’t exist. 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount: /Volumes/Media Archive-1, pid 53641 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount : succeeded on volume 0xffffff80d6355008 /Volumes/Media Archive-1 (error = 0, retval = 0) 12/27/13 10:49:32.000 PM kernel[0]: wlEvent: en0 en0 Link DOWN virtIf = 0 12/27/13 10:49:32.000 PM kernel[0]: AirPort: Link Down on en0. Reason 8 (Disassociated because station leaving). 12/27/13 10:49:32.000 PM kernel[0]: en0::IO80211Interface::postMessage bssid changed 12/27/13 10:49:33.681 PM configd[16]: network changed: v4(en0-:10.0.1.12) DNS- Proxy- SMB 12/27/13 10:49:33.697 PM configd[16]: network changed: DNS* Proxy 12/27/13 10:49:35.475 PM KernelEventAgent[57]: tid 00000000 received event(s) VQ_NOTRESP (1) 12/27/13 10:49:35.000 PM kernel[0]: ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0xffffff802176b4a0 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect started /Volumes/Media Archive-1 prevTrigger 0 currTrigger 1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: posting to KEA EINPROGRESS for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: Max reconnect time: 600 secs, Connect timeout: 15 secs for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 1 seconds and then try again 12/27/13 10:49:35.479 PM KernelEventAgent[57]: tid 00000000 type 'afpfs', mounted on '/Volumes/Media Archive-1', from '//Me@Capsule._afpovertcp._tcp.local/Media%20Archive', not responding 12/27/13 10:49:35.487 PM KernelEventAgent[57]: tid 00000000 found 1 filesystem(s) with problem(s) 12/27/13 10:49:36.692 PM com.bourgeoisbits.cloak.agent[14503]: NetworkProfile: (null), (null), (null) (Connected: NO, Airport: NO, Open: NO) [trusted] 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 2 seconds and then try again 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 4 seconds and then try again 12/27/13 10:49:41.000 PM kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=53662[GoogleSoftwareUp] clearing CS_VALID 12/27/13 10:49:42.102 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 2 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:42.113 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateProductID:] KSUpdateEngine updating product ID: "com.google.Keystone" 12/27/13 10:49:42.116 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 1 ticket(s). 12/27/13 10:49:42.121 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x531870 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x5302d0 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x534340 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:42.130 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x1a31a90 server=<KSOmahaServer:0x534340> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=1 activeTickets=1 rollCallTickets=1 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:42.292 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:42.296 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:42.299 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 8 seconds and then try again 12/27/13 10:49:43.152 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateAllProducts] KSUpdateEngine updating all installed products. 12/27/13 10:49:43.153 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 2 ticket(s). 12/27/13 10:49:43.158 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x18367a0 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x1837e10 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 >, <KSTicket:0x1834750 productID=com.google.talkplugin version=4.7.0.15362 xc=<KSPathExistenceChecker:0x1833890 path=/Library/Application Support/Google/GoogleTalkPlugin.app> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x52e930 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:43.159 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x53a210 server=<KSOmahaServer:0x52e930> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=2 activeTickets=1 rollCallTickets=2 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> <o:app appid="com.google.talkplugin" version="4.7.0.15362" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone, ... (2)) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:43.244 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:43.247 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:43.250 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:45.570 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 1 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 10 seconds and then try again 12/27/13 10:49:53.828 PM KernelEventAgent[57]: tid 00000000 unmounting 1 filesystems 12/27/13 10:49:53.000 PM kernel[0]: AFP_VFS afpfs_unmount: /Volumes/Media Archive-1, flags 524288, pid 57 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: get the reconnect token 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: GetReconnectToken failed 32 /Volumes/Media Archive-1 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_unmount : afpfs_DoReconnect sent signal for unmount to proceed 12/27/13 10:50:12.104 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon main] GoogleSoftwareUpdateDaemon inactive, shutdown. 12/27/13 10:50:29.396 PM Dock[93157]: no information back from LS about running process

    Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >