Search Results

Search found 15646 results on 626 pages for 'port 80'.

Page 265/626 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

  • Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

    - by Maalobs
    I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

    Read the article

  • Fatal error: Incompatible file format: The encoded file has format major ID 1, whereas the Loader expects 4 in ... on line 0

    - by Eugene
    I am using Ubuntu 10.04 and for some time I had to keep a downgraded PHP 5.2 package because I need to run Zend encrypted scripts. Recently I noticed that Zend released beta version of their loader (http://forums.zend.com/viewtopic.php?f=57&t=1365&start=80#p22073) so I updated to the native PHP 5.3 package, downloaded the .so file, added this to php.ini ;zend_extension=/etc/php5/ZendOptimizer.so zend_extension=/etc/php5/ZendGuardLoader.so zend_loader.enable=1 zend_loader.disable_licensing=0 zend_loader.obfuscation_level_support=3 and restarted the server. Now I am getting this error: Fatal error: Incompatible file format: The encoded file has format major ID 1, whereas the Loader expects 4 in ... on line 0 Do you by chance know an easy fix for this? Or should I downgrade back and wait till when they release something more stable?

    Read the article

  • Can't seem to install imagick

    - by PolishHurricane
    I'm trying to install the PHP PEAR PECL extension "imagick" (image magick), but failing horribly. It seems that I keed installing packages to progress, but this one has me stumped. It seems to fail all the way at the bottom. Please Note: I'm using ArchLinux, apt-get doesn't save me. [root@Crux tmp]# pecl install imagick downloading imagick-3.0.1.tgz ... Starting to download imagick-3.0.1.tgz (93,920 bytes) .....................done: 93,920 bytes 13 source files, building running: phpize Configuring for: PHP Api Version: 20100412 Zend Module Api No: 20100525 Zend Extension Api No: 220100525 Please provide the prefix of Imagemagick installation [autodetect] : building in /tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1 running: /tmp/pear/temp/imagick/configure --with-imagick checking for grep that handles long lines and -e... /usr/bin/grep checking for egrep... /usr/bin/grep -E checking for a sed that does not truncate output... /bin/sed checking for cc... cc checking whether the C compiler works... yes checking for C compiler default output file name... a.out checking for suffix of executables... checking whether we are cross compiling... no checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether cc accepts -g... yes checking for cc option to accept ISO C89... none needed checking how to run the C preprocessor... cc -E checking for icc... no checking for suncc... no checking whether cc understands -c and -o together... yes checking for system library directory... lib checking if compiler supports -R... no checking if compiler supports -Wl,-rpath,... yes checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking target system type... i686-pc-linux-gnu checking for PHP prefix... /usr checking for PHP includes... -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib checking for PHP extension directory... /usr/lib/php/modules checking for PHP installed headers prefix... /usr/include/php checking if debug is enabled... no checking if zts is enabled... no checking for re2c... re2c checking for re2c version... 0.13.5 (ok) checking for gawk... gawk checking whether to enable the imagick extension... yes, shared checking whether to enable the imagick GraphicsMagick backend... no checking ImageMagick MagickWand API configuration program... found in /usr/bin/MagickWand-config checking if ImageMagick version is at least 6.2.4... found version 6.7.8 Q16 checking for MagickWand.h header file... found in /usr/include/ImageMagick/wand/MagickWand.h checking PHP version is at least 5.1.3... yes. found 5.4.6 checking for ld used by cc... /usr/bin/ld checking if the linker (/usr/bin/ld) is GNU ld... yes checking for /usr/bin/ld option to reload object files... -r checking for BSD-compatible nm... /usr/bin/nm -B checking whether ln -s works... yes checking how to recognize dependent libraries... pass_all checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking dlfcn.h usability... yes checking dlfcn.h presence... yes checking for dlfcn.h... yes checking the maximum length of command line arguments... 1572864 checking command to parse /usr/bin/nm -B output from cc object... ok checking for objdir... .libs checking for ar... ar checking for ranlib... ranlib checking for strip... strip checking if cc supports -fno-rtti -fno-exceptions... no checking for cc option to produce PIC... -fPIC checking if cc PIC flag -fPIC works... yes checking if cc static flag -static works... yes checking if cc supports -c -o file.o... yes checking whether the cc linker (/usr/bin/ld) supports shared libraries... yes checking whether -lc should be explicitly linked in... no checking dynamic linker characteristics... GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... no creating libtool appending configuration tag "CXX" to libtool configure: creating ./config.status config.status: creating config.h running: make /bin/sh /tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1/libtool --mode=compile cc -I. -I/tmp/pear/temp/imagick -DPHP_ATOM_INC -I/tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1/include -I/tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1/main -I/tmp/pear/temp/imagick -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -I/usr/include/ImageMagick -DHAVE_CONFIG_H -g -O2 -c /tmp/pear/temp/imagick/imagick_class.c -o imagick_class.lo mkdir .libs cc -I. -I/tmp/pear/temp/imagick -DPHP_ATOM_INC -I/tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1/include -I/tmp/pear/temp/pear-build-rootLbSUWT/imagick-3.0.1/main -I/tmp/pear/temp/imagick -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -I/usr/include/ImageMagick -DHAVE_CONFIG_H -g -O2 -c /tmp/pear/temp/imagick/imagick_class.c -fPIC -DPIC -o .libs/imagick_class.o /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagematteâ: /tmp/pear/temp/imagick/imagick_class.c:268:2: warning: âMagickGetImageMatteâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:82) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getsizeoffsetâ: /tmp/pear/temp/imagick/imagick_class.c:406:2: warning: passing argument 2 of âMagickGetSizeOffsetâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:87:3: note: expected âssize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_paintfloodfillimageâ: /tmp/pear/temp/imagick/imagick_class.c:1016:3: warning: âMagickPaintFloodfillImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:99) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c:1019:3: warning: âMagickPaintFloodfillImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:99) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagepropertiesâ: /tmp/pear/temp/imagick/imagick_class.c:1083:2: warning: passing argument 3 of âMagickGetImagePropertiesâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:35:5: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimageprofilesâ: /tmp/pear/temp/imagick/imagick_class.c:1131:2: warning: passing argument 3 of âMagickGetImageProfilesâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:33:5: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_recolorimageâ: /tmp/pear/temp/imagick/imagick_class.c:1402:2: warning: âMagickRecolorImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:109) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_setfontâ: /tmp/pear/temp/imagick/imagick_class.c:1442:3: error: âstruct _php_core_globalsâ has no member named âsafe_modeâ /tmp/pear/temp/imagick/imagick_class.c:1442:3: error: âCHECKUID_CHECK_FILE_AND_DIRâ undeclared (first use in this function) /tmp/pear/temp/imagick/imagick_class.c:1442:3: note: each undeclared identifier is reported only once for each function it appears in /tmp/pear/temp/imagick/imagick_class.c:1442:3: error: âCHECKUID_NO_ERRORSâ undeclared (first use in this function) /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_queryformatsâ: /tmp/pear/temp/imagick/imagick_class.c:2580:2: warning: passing argument 2 of âMagickQueryFormatsâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:41:5: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_queryfontsâ: /tmp/pear/temp/imagick/imagick_class.c:2607:2: warning: passing argument 2 of âMagickQueryFontsâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:40:5: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_colorfloodfillimageâ: /tmp/pear/temp/imagick/imagick_class.c:3396:2: warning: âMagickColorFloodfillImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:75) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_mapimageâ: /tmp/pear/temp/imagick/imagick_class.c:3730:2: warning: âMagickMapImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:86) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_mattefloodfillimageâ: /tmp/pear/temp/imagick/imagick_class.c:3763:2: warning: âMagickMatteFloodfillImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:88) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_medianfilterimageâ: /tmp/pear/temp/imagick/imagick_class.c:3790:2: warning: âMagickMedianFilterImageâ is deprecated (declared at /usr/include/ImageMagick/wand/magick-image.h:217) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_paintopaqueimageâ: /tmp/pear/temp/imagick/imagick_class.c:3853:2: warning: âMagickPaintOpaqueImageChannelâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:104) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_painttransparentimageâ: /tmp/pear/temp/imagick/imagick_class.c:3916:2: warning: âMagickPaintTransparentImageâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:107) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_reducenoiseimageâ: /tmp/pear/temp/imagick/imagick_class.c:4059:2: warning: âMagickReduceNoiseImageâ is deprecated (declared at /usr/include/ImageMagick/wand/magick-image.h:266) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimageattributeâ: /tmp/pear/temp/imagick/imagick_class.c:5068:2: warning: âMagickGetImageAttributeâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:59) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagechannelextremaâ: /tmp/pear/temp/imagick/imagick_class.c:5253:2: warning: âMagickGetImageChannelExtremaâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:78) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c:5253:2: warning: passing argument 3 of âMagickGetImageChannelExtremaâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:68:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/deprecate.h:78:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c:5253:2: warning: passing argument 4 of âMagickGetImageChannelExtremaâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:68:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/deprecate.h:78:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimageextremaâ: /tmp/pear/temp/imagick/imagick_class.c:5506:2: warning: âMagickGetImageExtremaâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:80) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c:5506:2: warning: passing argument 2 of âMagickGetImageExtremaâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:68:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/deprecate.h:80:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c:5506:2: warning: passing argument 3 of âMagickGetImageExtremaâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:68:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/deprecate.h:80:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagehistogramâ: /tmp/pear/temp/imagick/imagick_class.c:5629:2: warning: passing argument 2 of âMagickGetImageHistogramâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:74:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-image.h:415:5: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagepageâ: /tmp/pear/temp/imagick/imagick_class.c:5740:2: warning: passing argument 2 of âMagickGetImagePageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:74:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-image.h:192:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c:5740:2: warning: passing argument 3 of âMagickGetImagePageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:74:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-image.h:192:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c:5740:2: warning: passing argument 4 of âMagickGetImagePageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:74:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-image.h:192:3: note: expected âssize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c:5740:2: warning: passing argument 5 of âMagickGetImagePageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:74:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-image.h:192:3: note: expected âssize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimageindexâ: /tmp/pear/temp/imagick/imagick_class.c:6344:2: warning: âMagickGetImageIndexâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:65) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_setimageindexâ: /tmp/pear/temp/imagick/imagick_class.c:6369:2: warning: âMagickSetImageIndexâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:113) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getimagesizeâ: /tmp/pear/temp/imagick/imagick_class.c:6447:2: warning: âMagickGetImageSizeâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:140) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_setimageattributeâ: /tmp/pear/temp/imagick/imagick_class.c:6796:2: warning: âMagickSetImageAttributeâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:111) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_flattenimagesâ: /tmp/pear/temp/imagick/imagick_class.c:7043:2: warning: âMagickFlattenImagesâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:132) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_averageimagesâ: /tmp/pear/temp/imagick/imagick_class.c:8079:2: warning: âMagickAverageImagesâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:131) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_mosaicimagesâ: /tmp/pear/temp/imagick/imagick_class.c:8516:2: warning: âMagickMosaicImagesâ is deprecated (declared at /usr/include/ImageMagick/wand/deprecate.h:135) [-Wdeprecated-declarations] /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getpageâ: /tmp/pear/temp/imagick/imagick_class.c:9126:2: warning: passing argument 2 of âMagickGetPageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:84:3: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c:9126:2: warning: passing argument 3 of âMagickGetPageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:84:3: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c:9126:2: warning: passing argument 4 of âMagickGetPageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:84:3: note: expected âssize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c:9126:2: warning: passing argument 5 of âMagickGetPageâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:84:3: note: expected âssize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getquantumdepthâ: /tmp/pear/temp/imagick/imagick_class.c:9154:2: warning: passing argument 1 of âMagickGetQuantumDepthâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:52:4: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getquantumrangeâ: /tmp/pear/temp/imagick/imagick_class.c:9176:2: warning: passing argument 1 of âMagickGetQuantumRangeâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:53:4: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getsamplingfactorsâ: /tmp/pear/temp/imagick/imagick_class.c:9247:2: warning: passing argument 2 of âMagickGetSamplingFactorsâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:59:4: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getsizeâ: /tmp/pear/temp/imagick/imagick_class.c:9273:2: warning: passing argument 2 of âMagickGetSizeâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:86:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c:9273:2: warning: passing argument 3 of âMagickGetSizeâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:86:3: note: expected âsize_t *â but argument is of type âlong unsigned int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_getversionâ: /tmp/pear/temp/imagick/imagick_class.c:9299:2: warning: passing argument 1 of âMagickGetVersionâ from incompatible pointer type [enabled by default] In file included from /usr/include/ImageMagick/wand/MagickWand.h:73:0, from /tmp/pear/temp/imagick/php_imagick.h:49, from /tmp/pear/temp/imagick/imagick_class.c:21: /usr/include/ImageMagick/wand/magick-property.h:55:4: note: expected âsize_t *â but argument is of type âlong int *â /tmp/pear/temp/imagick/imagick_class.c: In function âzim_imagick_setimageprogressmonitorâ: /tmp/pear/temp/imagick/imagick_class.c:9534:2: error: âstruct _php_core_globalsâ has no member named âsafe_modeâ /tmp/pear/temp/imagick/imagick_class.c:9534:2: error: âCHECKUID_CHECK_FILE_AND_DIRâ undeclared (first use in this function) /tmp/pear/temp/imagick/imagick_class.c:9534:2: error: âCHECKUID_NO_ERRORSâ undeclared (first use in this function) make: *** [imagick_class.lo] Error 1 ERROR: `make' failed

    Read the article

  • Using VLC as RTSP server

    - by StackedCrooked
    I'm trying to figure out how to use the server capabilities of VLC. More specifically, how to export an SDP file when RTP streaming. In chapter 4 in the section related to RTP Streaming examples for server and client are given: vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' vlc rtsp://server.example.org:8080/test.sdp It's not very clear to me how to make it actually work. I have tried these two commands for server and client using two cmd instances: vlc -I rc screen:// --sout=#rtp{dst=127.0.0.1,port=4444,sdp=rtsp://localhost:8080/test.sdp} vlc -I rc rtsp://localhost:8080/test.sdp Invoking the second command causes the first one to crash. The second command shows the error message "could not connect to localhost:8080".

    Read the article

  • https root webapp in jboss 5 through apache mod_proxy with ajp

    - by Jesus
    hi, i have apache 2.2.3 and jboss 5.1 installed in my server, in apache i have 2 apps in php+mysql and in jboss i have in the root app (/) liferay portal. i used mod_proxy to reach the jboss app : <VirtualHost server_ip:80> ServerName intranet.mycompany.com ProxyPreserveHost On ProxyPass / balancer://jbosscluster/ ProxyPassReverse / http://server_ip:8080 </VirtualHost> but now i have to enable https only in intranet.mycompany.com, and i dont know where configure the ssl, in apache, jboss, both. i tried in jboss in the server.xml, generating a selfsigned certificate with keytool, but apache doesnt forward to https://server_ip:8443 i will appreciate your help.

    Read the article

  • Fedora to Fedora remote desktop does not work (connection closed error, even after setting everything up)

    - by jonderry
    I'm trying to use remote desktop on my laptop (running Fedora) to my desktop (also running Fedora) on the same local network. I configured Remote Desktop on my desktop via System - Preferences - Remote Desktop, verified that the port is open by nmap, and attempted to connect from my laptop via vinagre (also tried appending :5900 for the port, and using the ip address). In all cases, the connection fails with a popup that says "Connection closed\n Connection to host was closed." EDIT: I am able to use vinagre from the desktop to remote desktop into itself, just not from one machine to the other. I tried vncviewer and a similar problem occurs (unable connect to socket: No route to host (113))

    Read the article

  • Cisco ASA Hairpinning with Dynamic IP

    - by Joseph Sturtevant
    I currently have my Cisco ASA 5505 firewall configured to forward port 80 from the outside interface to a host on my dmz interface. I also need to allow clients on my inside interface to access the host in the dmz by entering the public ip / dns record in their browsers. I was able to do that by following the instructions here, resulting in the following configuration: static (dmz,outside) tcp interface www 192.168.1.5 www netmask 255.255.255.255 static (dmz,inside) tcp 74.125.45.100 www 192.168.1.5 www netmask 255.255.255.255 (Where 74.125.45.100 is my public IP and 192.168.1.5 is the IP of the dmz host) This works great except for the fact that my network has a dynamic public IP and this configuration will therefore break as soon as my public IP changes. Is there a way to do what I want with a dynamic ip? Note: Adding an internal DNS record won't solve my problem since I have multiple dmz hosts mapped to different ports on the public IP.

    Read the article

  • How would I reset a usb hub multiplier driver?

    - by Cameron
    I have a usb port which connects a little man usb hub I got for Christmas. It worked fine to begin with however now it works on any computer other than my own. When I plug the man in it lights up and when I plug things into the man it says they have malfunctioned but when I plug them straight into tha port it's fine. Is there somesort of driver that needs to be refreshed? I have no idea how these work so please explain! I use windows 7 32bit.

    Read the article

  • Setting up SSL virtual hosts in Apache

    - by Bart van Heukelom
    I'm trying to set up SSL, with SNI, in my apache and am getting the often-seen "ssl_error_rx_record_too_long" error in Firefox when accessing the site (https://test.me.dev.xxxx.net), from which I can conclude that the server is listening on port 443, but doesn't know to use SSL on it. The server is Ubuntu 9.04 with Apache 2.2.11 I enabled SSL in the default way (a2enmod ssl). Here is my relevant config: NameVirtualHost *:* Listen 80 <IfModule mod_ssl.c> Listen 443 </IfModule> ... <VirtualHost *:*> DocumentRoot /home ServerAlias *.dev.xxxx.net UseCanonicalName Off # project.user.dev.xxxx.net VirtualDocumentRoot /home/%2/dev/%1/web SSLEngine On SSLCertificateFile /etc/apache2/certs/dev.crt SSLCertificateKeyFile /etc/apache2/certs/dev.key </VirtualHost> What is wrong?

    Read the article

  • FTP connection is aborted

    - by Conrad C
    I want to connect using FTP to my webpage hosted on ipages.com , but I always get this error on filezilla.: Status: Server does not support non-ASCII characters. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 550 PWD: Permission denied Error: Failed to retrieve directory listing Error: Disconnected from server: ECONNABORTED - Connection aborted It looks like the connection is established but then disconnects. Is it an issue with the host? I use the default port 21. The user-pass is working. And the ftp adress is ftp.mysite.com I tested the port 21 using netstat and I get 220 Ipage FTP Server Ready

    Read the article

  • Enabling fastCGI for php in PLESK 9.3 or use ningx

    - by Saif Bechan
    I have a server that runs PLESK. I can set php to use 3 options: apache module, fastCGI application, cgi application And i have a different option that just says enable fastCGI support. Which option is the best to choose from? I run an php application with mysql and some ajax. Heavy reads and writes, it is a busy website. Second thing is will there be much difference if i install nginx to work with this. there is some sort of hack i can use to make ningx work on port 80 and apache on port 8080. I don't know if this is worth my while. thanks for your time folks!

    Read the article

  • 8Gb Fiber Channcel HBA vs. 10 Gb SPF+ Converged HBA

    - by Hossein Aarabi
    I am putting a Dell server together, more specifically R720. I have to select the correct Host Bus Adapter. This HBA on R710 will connect to a storage device. I am confused between these two: QLogic 2562, Dual Port 8Gb Optical Fiber Channel HBA (price $2,045) QLogic 8262, Dual Port 10Gb SFP+, Converged Network Adapter (price $1,618) I thought since the QLogic 2562 is a fiber channel and is more expensive then it is faster in terms of IOPS. But, it is a 8Gb as opposed to 10 Gb of SFP+. My questions: Which one is better (IOPS performance, etc.)? Why should I choose one over another?

    Read the article

  • uwsgi_params not in nginx

    - by Halit Alptekin
    Firstly I setup nginx and uwsgi via apt-get. And,I add the line to nginx conf file(/etc/nginx/conf.d/default.conf) like below line; server { listen 80; server_name <replace with your hostname>; #Replace paths for real deployments... access_log /tmp/access.log; error_log /tmp/error.log; location / { include uwsgi_params; uwsgi_pass 127.0.0.1:8889; } } I had a error; Starting nginx: [emerg]: open() "/etc/nginx/uwsgi_params" failed (2: No such file or directory) in /etc/nginx/conf.d/default.conf:11 configuration file /etc/nginx/nginx.conf test failed If I add uwsgi_params file from uwsgi's source;I had a simple error. Thanks

    Read the article

  • Using Y split cables to connect two servers to a single PDU receptacle

    - by sagi
    We have bought a few 30amp 208v PDUs that only have 9 receptacles. The servers we are connecting to those PDUs will not use the full 30amps (at 80%, or actually 40% since we use redundant power) so we need to find a way to connect more than 9 servers to the same 9 receptacles so we'll be not wasting capacity that we pay for. I thought about using a Y split cable like this one: http://www.cablesandkits.com/power-cord-c14-c13-splitter-cable-awg-p-515.html That will let me connect two servers to a single receptacle. Each of the individual receptacles can provide 12 amps of power and individual servers are unlikely to consume more than 3 amps at maximal load so it should provide sufficient power. The question is if there is any other reason why this may be a bad idea and if there is any other solution other than buying PDUs with more receptacles (which I don't want to do because I must use horizontal PDU on these racks and ones with more receptacles consume more U space).

    Read the article

  • Apache Redirect to Jboss SSL

    - by Rick
    I'm trying to have an SSL Connection to an Apache server on port 443 which I want to use to proxy connections to a JBoss server on a different port. The SSL certificates sit on the Jboss server not on the Apache server. Is it possible to redirect HTTPS traffic from Apache to the Jboss Server and have the JBoss server do the SSL handshake? The Apache server must be able to redirect HTTPS traffic for two different URLS. One for a secure site. The other for access to web services. By the way I'm using it mutual authentication, if that makes any difference. What does the Apache config file need to contain? or are there any good example of this out there? Thanks

    Read the article

  • Lighttpd proxy module - use with hostname

    - by k_wave
    I have to proxy a site which is hosted on an external webspace through my lighty on example.org. My config so far: $HTTP["url"] =~ "^/webmail" { proxy.server = ("/webmail/" => ( # this entry should link to example2.org ("host" => "1.2.3.4", "port" => 80) )) } The webspace provider has configured my domain as vhost. So if i access http://1.2.3.4/webmail/ lighttpd will only deliver the main site of the webspace provider which says "Site example.org was not found on our server." Any suggestions how i have to configure lighty to proxy sites that are only hosted as vhost (and do not have an ip on their own)?

    Read the article

  • Why can blocked IPs get through my iptables? What's wrong with this configuration?

    - by NeedSomeHelp
    (Why can/How are) blocked IPs (get/getting) through my iptables? Hello and thanks for your consideration... I have configured iptables and included (below) output from the command "iptables --line-numbers -n -L" yet IP addresses (like 31.41.219.180) from IP blocks I have already blocked are getting through. Please take a look and share any input you may have. Thank you. P.S. The initial ACCEPT IP addresses are for CloudFlare. . Chain INPUT (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 32267 14M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 0 0 REJECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:!0x17/0x02 state NEW reject-with tcp-reset 3 149 8570 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 4 434 25606 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 5 0 0 ACCEPT udp -- * * 103.21.244.0/22 0.0.0.0/0 6 0 0 ACCEPT udp -- * * 103.22.200.0/22 0.0.0.0/0 7 0 0 ACCEPT udp -- * * 103.31.4.0/22 0.0.0.0/0 8 0 0 ACCEPT udp -- * * 104.16.0.0/12 0.0.0.0/0 9 0 0 ACCEPT udp -- * * 108.162.192.0/18 0.0.0.0/0 10 0 0 ACCEPT udp -- * * 141.101.64.0/18 0.0.0.0/0 11 0 0 ACCEPT udp -- * * 162.158.0.0/15 0.0.0.0/0 12 0 0 ACCEPT udp -- * * 173.245.48.0/20 0.0.0.0/0 13 0 0 ACCEPT udp -- * * 188.114.96.0/20 0.0.0.0/0 14 0 0 ACCEPT udp -- * * 190.93.240.0/20 0.0.0.0/0 15 0 0 ACCEPT udp -- * * 197.234.240.0/22 0.0.0.0/0 16 0 0 ACCEPT udp -- * * 198.41.128.0/17 0.0.0.0/0 17 0 0 ACCEPT udp -- * * 199.27.128.0/21 0.0.0.0/0 18 0 0 ACCEPT tcp -- * * 103.21.244.0/22 0.0.0.0/0 19 9 468 ACCEPT tcp -- * * 103.22.200.0/22 0.0.0.0/0 20 0 0 ACCEPT tcp -- * * 103.31.4.0/22 0.0.0.0/0 21 0 0 ACCEPT tcp -- * * 104.16.0.0/12 0.0.0.0/0 22 858 44616 ACCEPT tcp -- * * 108.162.192.0/18 0.0.0.0/0 23 376 19552 ACCEPT tcp -- * * 141.101.64.0/18 0.0.0.0/0 24 0 0 ACCEPT tcp -- * * 162.158.0.0/15 0.0.0.0/0 25 257 13364 ACCEPT tcp -- * * 173.245.48.0/20 0.0.0.0/0 26 0 0 ACCEPT tcp -- * * 188.114.96.0/20 0.0.0.0/0 27 0 0 ACCEPT tcp -- * * 190.93.240.0/20 0.0.0.0/0 28 0 0 ACCEPT tcp -- * * 197.234.240.0/22 0.0.0.0/0 29 0 0 ACCEPT tcp -- * * 198.41.128.0/17 0.0.0.0/0 30 92 4784 ACCEPT tcp -- * * 199.27.128.0/21 0.0.0.0/0 31 0 0 DROP tcp -- * * 1.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 32 0 0 DROP tcp -- * * 101.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 33 0 0 DROP tcp -- * * 102.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 34 0 0 DROP tcp -- * * 103.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 35 18 1080 DROP tcp -- * * 109.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 36 0 0 DROP tcp -- * * 112.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 37 12 656 DROP tcp -- * * 113.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 38 0 0 DROP tcp -- * * 114.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 39 0 0 DROP tcp -- * * 115.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 40 8 352 DROP tcp -- * * 116.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 41 0 0 DROP tcp -- * * 117.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 42 0 0 DROP tcp -- * * 118.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 43 2 120 DROP tcp -- * * 119.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 44 0 0 DROP tcp -- * * 120.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 45 0 0 DROP tcp -- * * 121.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 46 4 160 DROP tcp -- * * 122.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 47 4 240 DROP tcp -- * * 123.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 48 0 0 DROP tcp -- * * 125.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 49 0 0 DROP tcp -- * * 134.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 50 0 0 DROP tcp -- * * 146.185.0.0/16 0.0.0.0/0 tcp dpts:1:50000 51 6 360 DROP tcp -- * * 148.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 52 0 0 DROP tcp -- * * 151.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 53 0 0 DROP tcp -- * * 175.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 54 0 0 DROP tcp -- * * 176.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 55 0 0 DROP tcp -- * * 177.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 56 46 2696 DROP tcp -- * * 178.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 57 0 0 DROP tcp -- * * 179.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 58 4 224 DROP tcp -- * * 180.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 59 0 0 DROP tcp -- * * 181.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 60 0 0 DROP tcp -- * * 182.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 61 34 2040 DROP tcp -- * * 183.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 62 0 0 DROP tcp -- * * 185.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 63 0 0 DROP tcp -- * * 186.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 64 0 0 DROP tcp -- * * 187.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 65 18 912 DROP tcp -- * * 188.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 66 0 0 DROP tcp -- * * 189.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 67 0 0 DROP tcp -- * * 190.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 68 2 120 DROP tcp -- * * 192.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 69 0 0 DROP tcp -- * * 196.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 70 0 0 DROP tcp -- * * 197.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 71 5 300 DROP tcp -- * * 198.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 72 0 0 DROP tcp -- * * 2.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 73 0 0 DROP tcp -- * * 200.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 74 0 0 DROP tcp -- * * 201.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 75 6 360 DROP tcp -- * * 202.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 76 0 0 DROP tcp -- * * 203.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 77 4 160 DROP tcp -- * * 210.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 78 0 0 DROP tcp -- * * 211.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 79 2 96 DROP tcp -- * * 212.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 80 4 240 DROP tcp -- * * 213.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 81 0 0 DROP tcp -- * * 214.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 82 0 0 DROP tcp -- * * 215.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 83 0 0 DROP tcp -- * * 216.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 84 0 0 DROP tcp -- * * 217.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 85 4 172 DROP tcp -- * * 218.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 86 12 576 DROP tcp -- * * 219.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 87 7 372 DROP tcp -- * * 220.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 88 0 0 DROP tcp -- * * 222.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 89 0 0 DROP tcp -- * * 27.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 90 12 608 DROP tcp -- * * 31.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 91 11 528 DROP tcp -- * * 37.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 92 0 0 DROP tcp -- * * 41.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 93 0 0 DROP tcp -- * * 42.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 94 0 0 DROP tcp -- * * 43.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 95 8 480 DROP tcp -- * * 46.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 96 0 0 DROP tcp -- * * 49.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 97 6 360 DROP tcp -- * * 5.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 98 0 0 DROP tcp -- * * 58.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 99 0 0 DROP tcp -- * * 60.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 100 4 160 DROP tcp -- * * 61.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 101 32 1848 DROP tcp -- * * 62.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 102 0 0 DROP tcp -- * * 63.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 103 20 1200 DROP tcp -- * * 64.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 104 0 0 DROP tcp -- * * 65.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 105 266 15960 DROP tcp -- * * 66.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 106 3 180 DROP tcp -- * * 69.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 107 5 272 DROP tcp -- * * 72.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 108 0 0 DROP tcp -- * * 78.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 109 0 0 DROP tcp -- * * 81.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 110 3 180 DROP tcp -- * * 82.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 111 0 0 DROP tcp -- * * 83.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 112 8 384 DROP tcp -- * * 84.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 113 0 0 DROP tcp -- * * 85.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 114 0 0 DROP tcp -- * * 86.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 115 6 360 DROP tcp -- * * 87.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 116 7 408 DROP tcp -- * * 88.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 117 0 0 DROP tcp -- * * 89.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 118 0 0 DROP tcp -- * * 90.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 119 0 0 DROP tcp -- * * 91.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 120 3 152 DROP tcp -- * * 92.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 121 20 992 DROP tcp -- * * 93.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 122 9 512 DROP tcp -- * * 94.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 123 5 272 DROP tcp -- * * 95.0.0.0/8 0.0.0.0/0 tcp dpts:1:50000 124 0 0 DROP udp -- * * 1.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 125 0 0 DROP udp -- * * 101.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 126 0 0 DROP udp -- * * 102.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 127 0 0 DROP udp -- * * 103.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 128 0 0 DROP udp -- * * 109.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 129 0 0 DROP udp -- * * 112.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 130 0 0 DROP udp -- * * 113.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 131 0 0 DROP udp -- * * 114.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 132 1 112 DROP udp -- * * 115.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 133 0 0 DROP udp -- * * 116.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 134 0 0 DROP udp -- * * 117.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 135 0 0 DROP udp -- * * 118.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 136 0 0 DROP udp -- * * 119.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 137 0 0 DROP udp -- * * 120.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 138 0 0 DROP udp -- * * 121.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 139 0 0 DROP udp -- * * 122.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 140 0 0 DROP udp -- * * 123.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 141 0 0 DROP udp -- * * 125.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 142 0 0 DROP udp -- * * 134.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 143 0 0 DROP udp -- * * 146.185.0.0/16 0.0.0.0/0 udp dpts:1:50000 144 0 0 DROP udp -- * * 148.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 145 0 0 DROP udp -- * * 151.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 146 0 0 DROP udp -- * * 175.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 147 0 0 DROP udp -- * * 176.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 148 1 70 DROP udp -- * * 177.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 149 0 0 DROP udp -- * * 178.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 150 0 0 DROP udp -- * * 179.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 151 0 0 DROP udp -- * * 180.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 152 0 0 DROP udp -- * * 181.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 153 0 0 DROP udp -- * * 182.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 154 0 0 DROP udp -- * * 183.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 155 0 0 DROP udp -- * * 185.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 156 1 74 DROP udp -- * * 186.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 157 0 0 DROP udp -- * * 187.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 158 0 0 DROP udp -- * * 188.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 159 0 0 DROP udp -- * * 189.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 160 0 0 DROP udp -- * * 190.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 161 0 0 DROP udp -- * * 192.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 162 0 0 DROP udp -- * * 196.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 163 0 0 DROP udp -- * * 197.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 164 0 0 DROP udp -- * * 198.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 165 0 0 DROP udp -- * * 2.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 166 0 0 DROP udp -- * * 200.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 167 0 0 DROP udp -- * * 201.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 168 0 0 DROP udp -- * * 202.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 169 0 0 DROP udp -- * * 203.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 170 0 0 DROP udp -- * * 210.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 171 0 0 DROP udp -- * * 211.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 172 0 0 DROP udp -- * * 212.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 173 0 0 DROP udp -- * * 213.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 174 0 0 DROP udp -- * * 214.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 175 0 0 DROP udp -- * * 215.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 176 0 0 DROP udp -- * * 216.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 177 0 0 DROP udp -- * * 217.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 178 1 80 DROP udp -- * * 218.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 179 0 0 DROP udp -- * * 219.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 180 0 0 DROP udp -- * * 220.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 181 0 0 DROP udp -- * * 222.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 182 0 0 DROP udp -- * * 27.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 183 0 0 DROP udp -- * * 31.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 184 0 0 DROP udp -- * * 37.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 185 0 0 DROP udp -- * * 41.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 186 0 0 DROP udp -- * * 42.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 187 0 0 DROP udp -- * * 43.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 188 0 0 DROP udp -- * * 46.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 189 0 0 DROP udp -- * * 49.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 190 0 0 DROP udp -- * * 5.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 191 0 0 DROP udp -- * * 58.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 192 0 0 DROP udp -- * * 60.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 193 0 0 DROP udp -- * * 61.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 194 0 0 DROP udp -- * * 62.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 195 0 0 DROP udp -- * * 63.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 196 0 0 DROP udp -- * * 64.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 197 0 0 DROP udp -- * * 65.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 198 0 0 DROP udp -- * * 66.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 199 0 0 DROP udp -- * * 69.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 200 0 0 DROP udp -- * * 72.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 201 0 0 DROP udp -- * * 78.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 202 0 0 DROP udp -- * * 81.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 203 0 0 DROP udp -- * * 82.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 204 0 0 DROP udp -- * * 83.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 205 0 0 DROP udp -- * * 84.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 206 0 0 DROP udp -- * * 85.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 207 0 0 DROP udp -- * * 86.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 208 0 0 DROP udp -- * * 87.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 209 0 0 DROP udp -- * * 88.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 210 0 0 DROP udp -- * * 89.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 211 0 0 DROP udp -- * * 90.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 212 0 0 DROP udp -- * * 91.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 213 0 0 DROP udp -- * * 92.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 214 2 72 DROP udp -- * * 93.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 215 0 0 DROP udp -- * * 94.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 216 0 0 DROP udp -- * * 95.0.0.0/8 0.0.0.0/0 udp dpts:1:50000 217 0 0 DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:12443 218 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:11443 219 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:11444 220 23 1104 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:8447 221 24 1152 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:8443 222 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:8880 223 207 11096 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 224 19 996 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 225 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:21 226 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 227 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:587 228 4 216 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 229 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:465 230 14 840 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 231 2 120 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:995 232 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:143 233 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:993 234 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:106 235 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:3306 236 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:5432 237 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:9008 238 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:9080 239 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:137 240 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:138 241 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:139 242 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:445 243 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 244 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:53 245 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 246 73 4488 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 icmp type 8 code 0 247 77 23598 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 0 0 REJECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:!0x17/0x02 state NEW reject-with tcp-reset 3 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 4 0 0 ACCEPT all -- lo lo 0.0.0.0/0 0.0.0.0/0 5 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 31004 25M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 1 333 REJECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:!0x17/0x02 state NEW reject-with tcp-reset 3 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 4 434 25606 ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 5 328 21324 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0

    Read the article

  • JBoss AS 5: starts but can't connect (Windows, remote)

    - by Nuwan
    Hello I installed Jboss 5.0GA and Its works fine in localhost.But I want It to access through remote Machine.Then I bind my IP address to my server and started it.This is the command I used run.bat -b 10.17.62.63 Then the server Starts fine This is the console log when starting the server > =============================================================================== > > JBoss Bootstrap Environment > > JBOSS_HOME: C:\jboss-5.0.0.GA > > JAVA: C:\Program Files\Java\jdk1.6.0_34\bin\java > > JAVA_OPTS: -Dprogram.name=run.bat -server -Xms128m -Xmx512m > -XX:MaxPermSize=25 6m -Dorg.jboss.resolver.warning=true -Dsun.rmi.dgc.client.gcInterval=3600000 -Ds un.rmi.dgc.server.gcInterval=3600000 > > CLASSPATH: C:\jboss-5.0.0.GA\bin\run.jar > > =============================================================================== > > run.bat: unused non-option argument: ûb run.bat: unused non-option > argument: 0.0.0.0 13:43:38,179 INFO [ServerImpl] Starting JBoss > (Microcontainer)... 13:43:38,179 INFO [ServerImpl] Release ID: JBoss > [Morpheus] 5.0.0.GA (build: SV NTag=JBoss_5_0_0_GA date=200812041714) > 13:43:38,179 INFO [ServerImpl] Bootstrap URL: null 13:43:38,179 INFO > [ServerImpl] Home Dir: C:\jboss-5.0.0.GA 13:43:38,179 INFO > [ServerImpl] Home URL: file:/C:/jboss-5.0.0.GA/ 13:43:38,195 INFO > [ServerImpl] Library URL: file:/C:/jboss-5.0.0.GA/lib/ 13:43:38,195 > INFO [ServerImpl] Patch URL: null 13:43:38,195 INFO [ServerImpl] > Common Base URL: file:/C:/jboss-5.0.0.GA/common/ > > 13:43:38,195 INFO [ServerImpl] Common Library URL: > file:/C:/jboss-5.0.0.GA/comm on/lib/ 13:43:38,195 INFO [ServerImpl] > Server Name: default 13:43:38,195 INFO [ServerImpl] Server Base Dir: > C:\jboss-5.0.0.GA\server 13:43:38,195 INFO [ServerImpl] Server Base > URL: file:/C:/jboss-5.0.0.GA/server/ > > 13:43:38,210 INFO [ServerImpl] Server Config URL: > file:/C:/jboss-5.0.0.GA/serve r/default/conf/ 13:43:38,210 INFO > [ServerImpl] Server Home Dir: C:\jboss-5.0.0.GA\server\defaul t > 13:43:38,210 INFO [ServerImpl] Server Home URL: > file:/C:/jboss-5.0.0.GA/server/ default/ 13:43:38,210 INFO > [ServerImpl] Server Data Dir: C:\jboss-5.0.0.GA\server\defaul t\data > 13:43:38,210 INFO [ServerImpl] Server Library URL: > file:/C:/jboss-5.0.0.GA/serv er/default/lib/ 13:43:38,210 INFO > [ServerImpl] Server Log Dir: C:\jboss-5.0.0.GA\server\default \log > 13:43:38,210 INFO [ServerImpl] Server Native Dir: > C:\jboss-5.0.0.GA\server\defa ult\tmp\native 13:43:38,210 INFO > [ServerImpl] Server Temp Dir: C:\jboss-5.0.0.GA\server\defaul t\tmp > 13:43:38,210 INFO [ServerImpl] Server Temp Deploy Dir: > C:\jboss-5.0.0.GA\server \default\tmp\deploy 13:43:39,710 INFO > [ServerImpl] Starting Microcontainer, bootstrapURL=file:/C:/j > boss-5.0.0.GA/server/default/conf/bootstrap.xml 13:43:40,851 INFO > [VFSCacheFactory] Initializing VFSCache [org.jboss.virtual.pl > ugins.cache.IterableTimedVFSCache] 13:43:40,866 INFO > [VFSCacheFactory] Using VFSCache [IterableTimedVFSCache{lifet > ime=1800, resolution=60}] 13:43:41,616 INFO [CopyMechanism] VFS temp > dir: C:\jboss-5.0.0.GA\server\defaul t\tmp 13:43:41,648 INFO > [ZipEntryContext] VFS force nested jars copy-mode is enabled. > > 13:43:44,288 INFO [ServerInfo] Java version: 1.6.0_34,Sun > Microsystems Inc. 13:43:44,288 INFO [ServerInfo] Java VM: Java > HotSpot(TM) Server VM 20.9-b04,Sun Microsystems Inc. 13:43:44,288 > INFO [ServerInfo] OS-System: Windows XP 5.1,x86 13:43:44,569 INFO > [JMXKernel] Legacy JMX core initialized 13:43:50,148 INFO > [ProfileServiceImpl] Loading profile: default from: org.jboss > .system.server.profileservice.repository.SerializableDeploymentRepository@e72f0c > (root=C:\jboss-5.0.0.GA\server, > key=org.jboss.profileservice.spi.ProfileKey@143b > 82c3[domain=default,server=default,name=default]) 13:43:50,148 INFO > [ProfileImpl] Using repository:org.jboss.system.server.profil > eservice.repository.SerializableDeploymentRepository@e72f0c(root=C:\jboss-5.0.0. > GA\server, > key=org.jboss.profileservice.spi.ProfileKey@143b82c3[domain=default,s > erver=default,name=default]) 13:43:50,148 INFO [ProfileServiceImpl] > Loaded profile: ProfileImpl@8b3bb3{key=o > rg.jboss.profileservice.spi.ProfileKey@143b82c3[domain=default,server=default,na > me=default]} 13:43:54,804 INFO [WebService] Using RMI server > codebase: http://127.0.0.1:8083 / 13:44:12,147 INFO [CXFServerConfig] > JBoss Web Services - Stack CXF Runtime Serv er 13:44:12,147 INFO > [CXFServerConfig] 3.1.2.GA 13:44:29,788 INFO > [Ejb3DependenciesDeployer] Encountered deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:37,116 INFO [JMXConnectorServerService] JMX Connector > server: service:jmx > :rmi://127.0.0.1/jndi/rmi://127.0.0.1:1090/jmxconnector 13:44:38,022 > INFO [MailService] Mail Service bound to java:/Mail 13:44:43,162 WARN > [JBossASSecurityMetadataStore] WARNING! POTENTIAL SECURITY RI SK. It > has been detected that the MessageSucker component which sucks > messages f rom one node to another has not had its password changed > from the installation d efault. Please see the JBoss Messaging user > guide for instructions on how to do this. 13:44:43,209 WARN > [AnnotationCreator] No ClassLoader provided, using TCCL: org. > jboss.managed.api.annotation.ManagementComponent 13:44:43,600 INFO > [TransactionManagerService] JBossTS Transaction Service (JTA version) > - JBoss Inc. 13:44:43,600 INFO [TransactionManagerService] Setting up property manager MBean and JMX layer 13:44:44,366 INFO > [TransactionManagerService] Initializing recovery manager 13:44:44,678 > INFO [TransactionManagerService] Recovery manager configured > 13:44:44,678 INFO [TransactionManagerService] Binding > TransactionManager JNDI R eference 13:44:44,787 INFO > [TransactionManagerService] Starting transaction recovery man ager > 13:44:46,428 INFO [Http11Protocol] Initializing Coyote HTTP/1.1 on > http-127.0.0 .1-8080 13:44:46,459 INFO [AjpProtocol] Initializing > Coyote AJP/1.3 on ajp-127.0.0.1-80 09 13:44:46,459 INFO > [StandardService] Starting service jboss.web 13:44:46,475 INFO > [StandardEngine] Starting Servlet Engine: JBoss Web/2.1.1.GA > 13:44:46,616 INFO [Catalina] Server startup in 350 ms 13:44:46,709 > INFO [TomcatDeployment] deploy, ctxPath=/web-console, vfsUrl=manag > ement/console-mgr.sar/web-console.war 13:44:48,553 INFO > [TomcatDeployment] deploy, ctxPath=/juddi, vfsUrl=juddi-servi > ce.sar/juddi.war 13:44:48,678 INFO [RegistryServlet] Loading jUDDI > configuration. 13:44:48,694 INFO [RegistryServlet] Resources loaded > from: /WEB-INF/juddi.prope rties 13:44:48,709 INFO [RegistryServlet] > Initializing jUDDI components. 13:44:48,991 INFO [TomcatDeployment] > deploy, ctxPath=/invoker, vfsUrl=http-invo ker.sar/invoker.war > 13:44:49,162 INFO [TomcatDeployment] deploy, ctxPath=/jbossws, > vfsUrl=jbossws.s ar/jbossws-management.war 13:44:49,475 INFO > [RARDeployment] Required license terms exist, view vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jboss-local-jdbc.rar/META-INF/ra.xml > 13:44:49,569 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jboss-xa-jdbc.rar/META-INF/ra.xml > 13:44:49,741 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jms-ra.rar/META-INF/ra.xml > 13:44:49,819 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/mail-ra.rar/META-INF/ra.xml > 13:44:49,912 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/quartz-ra.rar/META-INF/ra.xml > 13:44:50,069 INFO [SimpleThreadPool] Job execution threads will use > class loade r of thread: main 13:44:50,115 INFO [QuartzScheduler] > Quartz Scheduler v.1.5.2 created. 13:44:50,131 INFO [RAMJobStore] > RAMJobStore initialized. 13:44:50,131 INFO [StdSchedulerFactory] > Quartz scheduler 'DefaultQuartzSchedule r' initialized from default > resource file in Quartz package: 'quartz.properties' > > 13:44:50,131 INFO [StdSchedulerFactory] Quartz scheduler version: > 1.5.2 13:44:50,131 INFO [QuartzScheduler] Scheduler DefaultQuartzScheduler_$_NON_CLUS TERED started. 13:44:51,194 INFO > [ConnectionFactoryBindingService] Bound ConnectionManager 'jb > oss.jca:service=DataSourceBinding,name=DefaultDS' to JNDI name > 'java:DefaultDS' 13:44:51,819 WARN [QuartzTimerServiceFactory] sql > failed: CREATE TABLE QRTZ_JOB > _DETAILS(JOB_NAME VARCHAR(80) NOT NULL, JOB_GROUP VARCHAR(80) NOT NULL, DESCRIPT ION VARCHAR(120) NULL, JOB_CLASS_NAME VARCHAR(128) NOT > NULL, IS_DURABLE VARCHAR( 1) NOT NULL, IS_VOLATILE VARCHAR(1) NOT > NULL, IS_STATEFUL VARCHAR(1) NOT NULL, R EQUESTS_RECOVERY VARCHAR(1) > NOT NULL, JOB_DATA BINARY NULL, PRIMARY KEY (JOB_NAM E,JOB_GROUP)) > 13:44:51,912 INFO [SimpleThreadPool] Job execution threads will use > class loade r of thread: main 13:44:51,928 INFO [QuartzScheduler] > Quartz Scheduler v.1.5.2 created. 13:44:51,928 INFO [JobStoreCMT] > Using db table-based data access locking (synch ronization). > 13:44:51,944 INFO [JobStoreCMT] Removed 0 Volatile Trigger(s). > 13:44:51,944 INFO [JobStoreCMT] Removed 0 Volatile Job(s). > 13:44:51,944 INFO [JobStoreCMT] JobStoreCMT initialized. 13:44:51,944 > INFO [StdSchedulerFactory] Quartz scheduler 'JBossEJB3QuartzSchedu > ler' initialized from an externally provided properties instance. > 13:44:51,959 INFO [StdSchedulerFactory] Quartz scheduler version: > 1.5.2 13:44:51,959 INFO [JobStoreCMT] Freed 0 triggers from 'acquired' / 'blocked' st ate. 13:44:51,975 INFO [JobStoreCMT] > Recovering 0 jobs that were in-progress at the time of the last > shut-down. 13:44:51,975 INFO [JobStoreCMT] Recovery complete. > 13:44:51,975 INFO [JobStoreCMT] Removed 0 'complete' triggers. > 13:44:51,975 INFO [JobStoreCMT] Removed 0 stale fired job entries. > 13:44:51,990 INFO [QuartzScheduler] Scheduler > JBossEJB3QuartzScheduler_$_NON_CL USTERED started. 13:44:52,381 INFO > [ServerPeer] JBoss Messaging 1.4.1.GA server [0] started 13:44:52,569 > INFO [QueueService] Queue[/queue/DLQ] started, fullSize=200000, pa > geSize=2000, downCacheSize=2000 13:44:52,584 INFO [QueueService] > Queue[/queue/ExpiryQueue] started, fullSize=20 0000, pageSize=2000, > downCacheSize=2000 13:44:52,709 INFO [ConnectionFactory] Connector > bisocket://127.0.0.1:4457 has l easing enabled, lease period 10000 > milliseconds 13:44:52,709 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@1a8ac5e > started 13:44:52,725 WARN [ConnectionFactoryJNDIMapper] > supportsFailover attribute is t rue on connection factory: > jboss.messaging.connectionfactory:service=ClusteredCo nnectionFactory > but post office is non clustered. So connection factory will *no t* > support failover 13:44:52,725 WARN [ConnectionFactoryJNDIMapper] > supportsLoadBalancing attribute is true on connection factory: > jboss.messaging.connectionfactory:service=Cluste redConnectionFactory > but post office is non clustered. So connection factory wil l *not* > support load balancing 13:44:52,740 INFO [ConnectionFactory] > Connector bisocket://127.0.0.1:4457 has l easing enabled, lease period > 10000 milliseconds 13:44:52,740 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@1d43178 > started 13:44:52,740 INFO [ConnectionFactory] Connector > bisocket://127.0.0.1:4457 has l easing enabled, lease period 10000 > milliseconds 13:44:52,756 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@52728a > started 13:44:53,084 INFO [ConnectionFactoryBindingService] Bound > ConnectionManager 'jb > oss.jca:service=ConnectionFactoryBinding,name=JmsXA' to JNDI name > 'java:JmsXA' 13:44:53,225 INFO [TomcatDeployment] deploy, ctxPath=/, > vfsUrl=ROOT.war 13:44:53,553 INFO [TomcatDeployment] deploy, > ctxPath=/jmx-console, vfsUrl=jmx-c onsole.war 13:44:53,975 INFO > [TomcatDeployment] deploy, ctxPath=/TestService, vfsUrl=TestS > erviceEAR.ear/TestService.war 13:44:55,662 INFO [JBossASKernel] > Created KernelDeployment for: myE-ejb.jar 13:44:55,709 INFO > [JBossASKernel] installing bean: jboss.j2ee:jar=myE-ejb.jar,n > ame=RPSService,service=EJB3 13:44:55,725 INFO [JBossASKernel] with > dependencies: 13:44:55,725 INFO [JBossASKernel] and demands: > 13:44:55,725 INFO [JBossASKernel] > jboss.ejb:service=EJBTimerService 13:44:55,725 INFO [JBossASKernel] > and supplies: 13:44:55,725 INFO [JBossASKernel] > jndi:RPSService/remote 13:44:55,725 INFO [JBossASKernel] Added > bean(jboss.j2ee:jar=myE-ejb.jar,name=RP SService,service=EJB3) to > KernelDeployment of: myE-ejb.jar 13:44:56,772 INFO > [SessionSpecContainer] Starting jboss.j2ee:jar=myE-ejb.jar,na > me=RPSService,service=EJB3 13:44:56,803 INFO [EJBContainer] STARTED > EJB: com.monz.rpz.RPSService ejbName: RPSService 13:44:56,819 INFO > [JndiSessionRegistrarBase] Binding the following Entries in G lobal > JNDI: > > > 13:44:57,381 INFO [DefaultEndpointRegistry] register: > jboss.ws:context=myE-ejb, endpoint=RPSService 13:44:57,428 INFO > [DescriptorDeploymentAspect] Add Service id=RPSService > address=http://127.0.0.1:8080/myE-ejb/RPSService > implementor=com.monz.rpz.RPSService > invoker=org.jboss.wsf.stack.cxf.InvokerEJB3 mtomEnabled=false > 13:44:57,459 INFO [DescriptorDeploymentAspect] JBossWS-CXF > configuration genera ted: > file:/C:/jboss-5.0.0.GA/server/default/tmp/jbossws/jbossws-cxf1864137209199 > 110130.xml 13:44:57,569 INFO [TomcatDeployment] deploy, ctxPath=/myE-ejb, vfsUrl=myE-ejb.j ar 13:44:57,709 WARN [config] > Unable to process deployment descriptor for context '/myE-ejb' > 13:44:59,334 INFO [Http11Protocol] Starting Coyote HTTP/1.1 on > http-127.0.0.1-8 080 13:44:59,397 INFO [AjpProtocol] Starting Coyote > AJP/1.3 on ajp-127.0.0.1-8009 13:44:59,459 INFO [ServerImpl] JBoss > (Microcontainer) [5.0.0.GA (build: SVNTag= JBoss_5_0_0_GA > date=200812041714)] Started in 1m:21s:233ms But Still I cant connect to It when I Type my IP address in my browser thanks

    Read the article

  • Option 82 and dhcpd. "No free leases" for second computer

    - by SaveTheRbtz
    There is DHCP server in network (isc-dhcpd-server-3.0 on FreeBSD 7.2) than gives one IP per switch port to every user via Option 82 The problem appears when user disconnects one of his computers and connects another(i.e notebook with different MAC address) then DHCPD puts to log "...network net1: no free leases", because there is record in leases file that this IP is already owned by another MAC. That second computer will have his IP only after default-lease-time (that is IIRC minimum 10min, and after 3min he usually calling support) or after deletion of dhcpd.leases file and restart of dhcpd. Is there a way to turn leases off at all, because we have strict binding between switch-port-ip?

    Read the article

  • AIX: iscsi volumes disappear after reboot

    - by Dan
    We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet port for iSCSI exclusively.) When we reboot the AIX box, the iSCSI volume doesn't get mounted (which is fine; I've figured out that it fails to mount because AIX tries mounting it's volumes before starting the networking stack.) The problem is, after the server has booted it fails to redetect the iSCSI target as a physical disk. This means the volume group (iscsivg) can't go online. if I run cfgmgr -v to redetect the iscsi volume it successfully detects the iscsi target volume and creates a physical volume reference, but allocates it a different volume ID to what was defined before. eg - rootvg contains hdisk 0 and 1 iscsivg was originally defined with hdisk2 as the physical iSCSI volume. after reboot and running cfgmgr -v, AIX detects physical volumes hdisk0, hdisk11 and hdisk3. As there's no hdisk2, I can't varyon the iscsivg volume group. I can't seem any existing hdisk2 definition in the ODM. I can't easily add or change the definition of the physcial disk in the iscsivg volume group as it won't "varyon". Exporting the volume group deletes it completely, recreating the volume group by "importing" it from the reallocated disk makes it available again, but surely there's a better way? Can I force a specific hdisk drive designation for an iscsi target? How do you bring online iSCSI volumes after a reboot? I assume this "just works" with a dedicated HBA instead of a generic ethernet adapter? By the way, the iSCSI volume works fine once it's mounted; we only have problems getting it working - and only with AIX. The iSCSI array works fine with our Linux and Windows servers; ie the volumes get detected and remounted after boot time without any problems, using generic ethernet adapters. Here's some of the config from the AIX box: defined disks / devices: # lsdev hdisk0 Available 06-08-01-5,0 16 Bit LVD SCSI Disk Drive hdisk1 Available 06-08-01-8,0 16 Bit LVD SCSI Disk Drive hdisk3 Available Other iSCSI Disk Drive iscsi0 Available iSCSI Protocol Device scsi0 Available 06-08-00 PCI-X Dual Channel Ultra320 SCSI Adapter bus scsi1 Available 06-08-01 PCI-X Dual Channel Ultra320 SCSI Adapter bus ses0 Available 06-08-01-15,0 SCSI Enclosure Services Device sisscsia0 Available 06-08 PCI-X Dual Channel Ultra320 SCSI Adapter iscsi target definition in /etc/iscsi/targets: # IBM DS3300 disk array # port 1 on second controller 10.10.xx.xxx 3260 iqn.1992-01.com.lsi:1535.600a0b80005b0a7fxxxxxxxxxxxx physical volumes (after reimporting the volume group) # lspv hdisk0 0003b08a0d4936b6 rootvg active hdisk1 0003b08aaa5cb366 rootvg active hdisk3 0003b08a032d04bb iscsivg active

    Read the article

  • DD-WRT Router acting as a Switch and Wi-Fi AP

    - by dotnetchris
    Recently I upgraded to Comcast Business and their modem has a built-in router so I took off my DD-WRT router and moved to a location in my home where I needed more ports and Wi-Fi (preferably without running new Ethernet cables since it's 50-100 foot run through floor and ceilings). I have my network cable from my Comcast modem going into Port 1 of my DD-WRT router with Port 2 and 3 being networked PCs. I have DD-WRT setup as a DHCP forwarder with the firewall disabled. This lets my all of my devices access the network fine. Is the correct the way to do this? Or is this a less optimal solution and it should be done in a slightly different way?

    Read the article

  • opening socket to google hangs on SYN_SENT

    - by puchu
    I have 2 computers now: downloader (asus at4nm10t-i) with debian and desktop (asus sabertooth 990fx) with gentoo in the same network under NAT even with the same ethernet card: RTL8111E. driver r8169 is compiled as module on both computers. Sometimes in evenings desktop cannot connect to google and all its services like now: curl -v http://www.google.by on downloader it received server's answer immediately. on desktop it hanged and when I ran in other terminal: netstat -ntp | grep curl >>tcp 0 1 192.168.0.7:54126 173.194.35.191:80 SYN_SENT 4876/curl after 1-2 minutes it received server's answer. I was tried to change ip of network, mac address of desktop but nothing changed. When I was trying to connect to another services except google: curl -v http://www.yahoo.com both computers received answers immediately! Only when I rebooted desktop it begins to work with google services correctly I cant understand what is this bug related to. In which bugtracker should I post this: r8169 or linux kernel or google? PS. Desktop was checked with memtest: 5 passes - no errors

    Read the article

  • dns service on OS X Snow Leopard Server

    - by Sorin Buturugeanu
    Hello all, I have a Mac Mini (1.83GHz, 1.5 RAM) with a fresh install of OS X Snow Leopard Server and I want to use it for DNS and web hosting. What I have done so far is to go to the domain registrar and configure a new nameserver (ns.domain.tld) to point to my static IP. This Mac Mini is behind a DI-524 router and I have forwarded ports 53 and 80 to the Mini. I have also added the domain name to the DNS configuration pannel (as in the attachment), but intodns.com gives the following error (among others, and obviously the site is not working): "Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records." I don't know where to go from here .. Thank you to anyone willing to take the time to give me a hint!! seems that I can't post images but here's the link: http://i.imgur.com/zWI7Y.png

    Read the article

  • How to hack airport extreme to support USB 3G modem?

    - by Mike Caron
    Has anyone out there ever tried to hack the Airport Extreme, specifically with regard to the USB port? There are many cellular routers available that provide WiFi sharing of a USB modem link. However, instead of buying yet another router, I'd like to use my expensive Airport Extreme with it. The AE has a USB port on the back, but it's been said that it only talks to printers. Is there a way to hack the USB driver on the AE to allow it to recognize a USB modem, then use that as the connectivity instead of the LAN? I would imagine that one could use OpenFirmware to boot something on the AE. If one can boot it, then one could provide access using SSH across the lan. Once access is granted, then let the hacking begin... but I don't know how to (a) get the mini-osx on to USB (is it the same as the ATV without a UI?) or (b) how to load up certain things once boot has begun.

    Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >