Search Results

Search found 13968 results on 559 pages for 'device dependent routing'.

Page 267/559 | < Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >

• "Document in ADF" on Canon MX340

  - by Michael Donohue

  I have a Canon MX340 multifunction printer. Recently, it keeps saying "Document in ADF" when I turn on the printer. I've tried clearing this multiple times, but as soon as the feeder wheels stop turning, in an attempt to clear the document feeder, it just pops up the same error again. This is particularly annoying, as it blocks all functions on the device - I cannot print, even though printing has no interaction with the document feeder. I've opened up the feeder device, as much as can be done with fingers alone. There just doesn't seem to be anything in there. I ran a sheet of paper through about six times, just to see if some dust might be getting in the way, and I've blown out the feeder with air. Still nothing. At this point, I don't care too much about the ADF working, I just want to disable whatever sensor is tripping this error message. Any ideas? I found this thread online, where a user has the same problem. But no resolution was reached there.

  Read the article

• Trying to retrieve data with a thermaltake blacX enclosure: Windows 7 believes the drive to be "uninitialized"

  - by Peeter Joot

  I have a laptop that won't boot. It appears to be a power problem ... laptop auto-turns-off within about 10 seconds of pressing the power button (with power buttons lighted temporarily and no display with or without external monitor). I've followed the dell troubleshooting guide which suggested reseating the memory modules and the hard drives, but that didn't help. Before trying to have the laptop serviced, I wanted to get some data off off the hard drive. I bought a thermaltake blacX enclosure, intending to use this to both use to retrieve the drive data with, and then later use as external storage. Following the instructions (insert cables, insert drive power on) goes fine, and Windows 7 on another laptop installs the device driver software. However, no drive letter shows up in 'Computer'. Under Computer-manage-storage I see the drive is there, and there's an option to "initialize" the drive. The Windows "initialize" dialog gives me the option to pick between "MBR" and "GPT" partitioning, which sounds like a good way to destroy the data on the drive. I'm thinking that I've purchased the wrong device for the job (or that my old drive is damaged). The old drive to recover info from is a Western Digital 500G/7200rpm SATA drive if that is relavent. Both the original laptop and the one I'm using for recovery are running Windows 7. Does anybody have experience with using a blacX enclosure to recover data off an already formatted drive?

  Read the article

• Fixing damaged partition table

  - by dr4cul4

  This is continuation of Recover Extended Partition , but this time I have different problem related partition table it self. I managed to restore partition that I needed and backed up files that were crucial to me (at least those that I had space to store somewhere) OK now get to the problem. My partition table is corrupted, booting RIP Linux I can mount it in truecrypt (and other ones that recovered), but that's basically it. When I launch GParted I have unallocated drive. GParted Dev info: Device Information Model: ATA ST2000DL003-9VT1 Size: 1.82TiB Path: /dev/sda Partition table: unrecognized Heads: 255 Sectors/track: 63 Cylinders: 243201 Total Sectors: 3907029168 Sector size: 512 When I check information on unallocated space I get: File system: unallocated Size: 1.82TiB First sector: 0 Last sector: 3907029167 Total sectors: 3907029168 Warning: Can't have a partition outside the disk! Now the output of testdisc (Analyze): TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 Current partition structure: Partition Start End Size in sectors > 1 P Linux 13132 242 39 16353 233 8 51744768 2 E extended LBA 16807 223 1 243201 254 63 3637021626 No partition is bootable 5 L Linux 16807 223 57 20430 39 25 58191872 X extended 20430 70 1 243201 78 13 3578816632 Invalid NTFS or EXFAT boot 6 L HPFS - NTFS 20430 71 58 243201 78 13 3578816512 6 LNext Now fdisk: # fdisk -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00039cd0 Device Boot Start End Blocks Id System /dev/sda1 210980864 262725631 25872384 83 Linux /dev/sda2 270018504 3907040129 1818510813 f W95 Ext'd (LBA) /dev/sda5 270018560 328210431 29095936 83 Linux /dev/sda6 328212480 3907028991 1789408256 7 HPFS/NTFS/exFAT Now I would like to fix that to arrange partitions correctly, but I have no idea which tool is capable of fixing that (tried, a few, some of them offered fixing, but it was to risky at the moment - still backing up data).

  Read the article

• disk partition centos

  - by FlourishDNA

  I am setting up server for hosting two WordPress which has size of around 70GB. I have already installed CentOS as OS and I would like to partition the Disk. Is there any tool which can help me or can someone guide me though the process as I am not expert is SSH commands. Here are some output that might help. OS: CentOS release 6.3 fdisk -l Disk /dev/xvdb: 214.7 GB, 214748364800 bytes 255 heads, 63 sectors/track, 26108 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b91e0 Device Boot Start End Blocks Id System Disk /dev/xvda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e542c Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/vg_flourish-lv_root: 16.7 GB, 16718495744 bytes 255 heads, 63 sectors/track, 2032 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_flourish-lv_swap: 4227 MB, 4227858432 bytes 255 heads, 63 sectors/track, 514 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 df Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_flourish-lv_root 16070076 758184 14495560 5% / tmpfs 958500 0 958500 0% /dev/shm /dev/xvda1 495844 31926 438318 7% /boot df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_flourish-lv_root 16G 741M 14G 5% / tmpfs 937M 0 937M 0% /dev/shm /dev/xvda1 485M 32M 429M 7% /boot Thanks

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Z.

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• Dedicated Mouse and Keyboard on Virtual Box VM

  - by Myersguy

  To all super users, Currently I am trying to run virtual box on my second monitor, with a dedicated mouse and keyboard. However, doing so has not proven easy. There has been times where the mouse works, but not the keyboard, vice versa, or nothing works at all. The biggest problem I am running into is this: When enabling the USB mouse and keyboard from the VM, I get an error: 'USB Device is busy with a previous request.' The only thing that is using second mouse and keyboard, however, is Windows. The other error I have received stated that the VM was unable to create a proxy for the device. Additionally, the VM occasionally will disable the secondary keyboard entirely, requiring me to unplug and replug it into my PC to re-enable it again. Keyboard auto-capture is disabled, and while a solution I was reading online stated to turn off mouse integration, that option is grayed out on my machine. Any help would be appreciated. Thanks. /firstquestion.

  Read the article

• USB 3.0 ports backwards compatibility problems with 2.0 devices?

  - by AaronLS

  I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Hi, Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Secure NAT setup with iptables

  - by TheBigB

  I have Debian running device that needs to act as an internet-gateway. On top of that I want to provide a firewall that not only blocks inbound traffic, but also outbound traffic. And I figured iptables should be able to do the job. The problem: I've configured NAT properly (I think?), but once I set the default policy to DROP and add rules to for instance allow HTTP traffic from inside the LAN, HTTP is not going through. So basically my rules don't seem to work. Below is the initialization script that I use for iptables. The device has two NICs, respectively eth0 (the WAN interface) and eth1 (the LAN interface). echo 1 > /proc/sys/net/ipv4/ip_forward # Flush tables iptables -F iptables -t nat -F # Set policies iptables -P INPUT DROP iptables -P OUTPUT DROP # NAT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT # Allow outbound HTTP from LAN? iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT Can anyone shed some light on this?

  Read the article

• Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

  - by delta1

  I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

  Read the article

• Hard Reset USB in Ubuntu 10.04

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• Did Adobe Photoshop just killed my Graphics Card for good?

  - by user6004

  I was working with Adobe Photoshop, just some regular work, when I came to edit a PSD file and change the text of some layer, when all of a sudden the PC froze. No mouse, screen is frozen, keyboard strokes aren't getting me anything, no Task Manager, nada. So I rebooted my PC, and then something quite terrifying appeared before my eyes. It was not the Checkdisk utility that was launched, that made me terrified (by the way, that reboot damaged the partition table of an external HDD that was connected at the time to my PC, but that's another story). It was the screen itself. Please have a look. So after Checkdisk finished and Windows loaded, I noticed that the resolution was not right. Instead of 1440x900 which I had set, it was 1280x1024. When I went to change it back, I had no option to change back to my old resolution, and has only 3 other general resolution properties, as if my Video Card (GeForce 8800 GTS btw) was not recognized. And what do you know, in the Device Manager it appeared with an exclamation mark. Inside the hardware, it said this: Windows has stopped this device because it has reported problems. (Code 43) Uninstalling the drivers, downloading the newest drivers from NVIDIA and installing them did not work. It always comes back to this. So, do you have any advice before I go out and buy a new graphics card? I thought this was the only option left, but maybe the experts at Super User can help me out. By the way, the dotted screen appears after every reboot, and I see the dots when the ASUS Motherboard screen shows up at boot. Thanks in advance.

  Read the article

• Designing a persistent asynchronous TCP protocol

  - by dogglebones

  I have got a collection of web sites that need to send time-sensitive messages to host machines all over my metro area, each on its own generally dynamic IP. Until now, I have been doing this the way of the script kiddie: Each host machine runs an (s)FTP server, or an HTTP(s) server, and correspondingly has a certain port opened up by its gateway. Each host machine runs a program that watches a certain folder and automatically opens or prints or exec()s when a new file of a given extension shows up. Dynamic IP addresses are accommodated using a dynamic DNS service. Each web site does cURL or fsockopen or whatever and communicates directly with its recipient as-needed. This approach has been suprisingly reliable, however obvious issues have come up and the situation needs to be addressed. As stated, these messages are time-sensitive and failures need to be detected within minutes of submission by end-users. What I'm doing is building a messaging protocol. It will run on a machine and connection in my control. As far as the service is concerned, there is no distinction between web site and host machine -- there is only one device sending a message to another device. So that's where I'm at right now. I've got a skeleton server and a skeleton client. They can negotiate high-quality authentication and encryption. The (TCP) connection is persistent and asynchronous, and can handle delimited (i.e., read until \r\n or whatever) as well as length-prefixed (i.e., read exactly n bytes) messages. Unless somebody gives me a better idea, I think I'll handle messages as byte arrays. So I'm looking for suggestions on how to model the protocol itself -- at the application level. I'll mostly be transferring XML and DLM type files, as well as control messages for things like "handshake" and "is so-and-so online?" and so forth. Is there anything really stupid in my train of thought? Or anything I should read about before I get started? Stuff like that -- please and thanks.

  Read the article

• Putting and configuring grub on an external drive

  - by HisDudeness

  I want to put a bunch of minor emergency operating systems (such as GParted Live, DSL, Puppy Linux and so on) on a partitioned USB pen drive, with a dedicated grub boot loader on it, which I want to start when I select the drive in the BIOS to boot. The problem is: when writing grub boot options I must tell where kernel and initial ram files are located, but the USB drive can have different letters depending on when I did plug it in, if some others external drive were mounted. So, how can I write appropriate options which automatically refer to the drive grub is installed on without having to specify absolute paths, which might change (I mean, like (hd1,msdos1) ot /dev/sdb1)? And, while we are at it, can I have grub working on a device without an operating system on it to which it can refer? I mean, I want to address the command sudo grub-install /dev/sdb from the LMDE system I'm on right now, but I won't have LMDE on my pen drive. Is that a problem? And installing grub on another device, will I keep the grub I have right now on my HDD?

  Read the article

• Install Peppermint OS three on Asus EeePC

  - by Kithoth

  I just had a new Asus EeePC R051CX. Out of the box, the installed OS is Ubuntu 12.04 LTS, but I am trying to install Peppermint OS three (as single boot). Problem. Once on live CD (well, live USB stick...), I'm in trouble in both following situations: Try Peppermint OS Live In this case, the first thing I get is a message reading The system is running in low-graphics mode Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself. I can solely press "return" to accept, then I have a list of 4 options to answer the question "What would you like to do?". But I simply can't do anything at this moment, except switching to console mode or rebooting (keyboard / mouse controls don't allow me to do anything else). Install Peppermint OS Something I really don't understand... it launches the Ubuntu Recovery Media (which was already installed when I received the device)! Also, it says in the bottom ERROR: This recovery media only functions on Ubuntu systems. All I can do is quit (that is, reboot). One last important thing that comes to my mind: this stick worked just fine on the other computers I've tried it on. I really hope someone could bring me the light, a friend of mine told me how cool this OS is for EeePCs. Don't want to give up! Thanks. Edit I finally could install Peppermint, but not by understanding why I couldn't do it the logical way. Instead, I reinstalled Ubuntu myself (erasing the factory one). Then, I could simply boot on my live USB and perform a fresh install of Peppermint. So, I still don't know how and why the mentioned problem occurred.

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• How can I determine the IP addresses allocated by DHCP on a router that I'm connected to?

  - by user234831

  This "router" is not a typical situation. I'm using my phone as a hotspot and can only configure a select number of DHCP options. I can manage the limit on how many devices/clients can use my phone as a hotspot. I have to select from a radio-button list with the options: 2,3,4,5, or 8 I can specify the DHCP starting IP address. In this case, it begins at 192.168.6.106 When I'm connected via WIFI to my phone, an ipconfig /all command shows me that the default gateway is 192.168.6.1 and my IPv4 address is 192.168.1.148. I have the luxury of connecting another device to the phone and that device was assigned 192.168.1.121. I've tried connecting to 192.168.6.1, hoping for some sort of router setup page that I'm used to seeing, but there is no such thing or maybe it's just a matter of incompatable operating systems. In summary, the "router" (phone) has an IP address of 192.168.6.1 and a DHCP server that begins at 192.168.6.106 and allows up to 8 connections. Normally, I would assume a range of 192.168.6.106 - 192.168.6.113, but connected clients are showing otherwise. How can I figure out which IP addresses are set aside by DHCP for clients?

  Read the article

• iptables, forward traffic for ip not active on the host itself

  - by gucki

  I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

  Read the article

• Cisco ASA 5505 network route for static IP hosts

  - by TheCapn

  I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

  Read the article

• Running Windows 7 physical disk virtualized under Linux

  - by CajunLuke

  I have an existing Windows 7 installation that I'd like to virtualize under Linux. Windows boots fine on Disk A, Linux boots fine on Disk B. (Both disks are SATA.) I can mount the Windows disk when in Linux. I've tried VirtualBox and VMWare Player and neither will allow me to boot from the other disk. VirtualBox doesn't seem to have the option to do so. VMWare Player has the option to have an IDE drive exposed to the virtual environment as a SCSI disk. I've tried that, but it throws the error "Cannot connect virtual device ide1:0 because no corresponding device is available on the host." I've verified that it's pointing to the correct hard drive. I'm willing to try other virtualization products, and I'm not averse to spending a little money to get this to work. I've seen this other question, and it's not a duplicate, as I haven't gotten that far yet. I'm also interested in solutions going the other way (Linux on Windows), but that'd be lagniappe. Gory Hardware Details: Lenovo T410, 2.4 GHz Core i5 (has virtualization extensions), 4GiB RAM, 2x 320 GiB SATA HDD, one in optical bay. Fedora 14 2.6.35.10-74.fc14.x86_64, Windows 7 32-bit.

  Read the article

• Will the removal of NAT (with the use of IPv6) be bad for consumers? [closed]

  - by Jonathan.

  Possible Duplicate: How will IPv6 impact everyday users? (World IPv6 Day) As I understand when we have finally made the switch to IPv6 not only will NAT be unnecessary but it is incompatible with IPv6? Will that mean that ISPs will have to serve multiple IP addresses per customer? Will they provide a range of addresses for each customer or as each device connects will they get an IP address that isn't necessarily near that of the other devices in their house? But overall will this be bad for the Internet users? as surely it will allow ISPs to see exactly how many devices are being used, and so allow them to charge for the use of additional IP addresses? And then if that happens, what happens when you try to connect an extra device to your network? Will it simply not get an IP address? In my home we have about 15-20 devices connected at once, but for places where there are hundreds of devices, it seems like the perfect opportunity for ISPs to charge more? I think I may have it completely wrong, so is there somewhere where there is an explanation of who things will work when IPv6 becomes the norm?

  Read the article

• Could I have destroyed Partitioning-Scheme/Filesystem of HDDs with External Harddrive Case with builtin Raid-Controller?

  - by th3m3s

  I had just recently bought a Fantec QB-35US3R to have a nice box on my desk to make some backups to. Along with the HDD-Bay I had ordered some 4TB HDDs to let them run in Raid 5, which is handled by the hardware RAID controller of the Fantec HDD-Bay. The QB-35US3R arrived a few days before the hard drives, so I got impatient and had the idea to put three old 1TB disks in the Fantec device, just to test it... Long story short: I made a backup of the most important data on these three disks before they broke. I had set the configuration scheme to RAID 3 at the Fantec device. It seems, that the Fantec RAID controller has "somehow" destroyed the partitioning scheme or the file system, because when put into a HDD docking station, they get recognized by the OS (Ubuntu/Linux) but are not mountable anymore. I tried to recover the data from one HDD via gParted (parted), which ran some hours without success. Here I stopped, before trying other tools, cos I read that the longer a hard drive is running after a the partitioning got destroyed, the worse it gets. What could the HDD-Bay probably have done to my lovely hard drive disks? Is there some routine a RAID controller is executing, when it wants to create a RAID system? Like erasing the partition table (seems not plausible to me.) or writing some information to every hard drive in the RAID (seems more likely to me.)? Is there a chance to recover the data from these HDDs, or is the change a RAID controller makes so significant, that no software is of help?

  Read the article

• Hard Reset USB in Ubuntu 10.04

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

< Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >