Search Results

Search found 2968 results on 119 pages for 'cable modem'.

Page 27/119 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• Use two networks at the same time?

  - by Christopher

  I want to use Ubuntu 10.10 Server in a classroom, a computer lab whose bandwidth is provided by a local cable ISP. That's no problem, though the school network has an IP printer that I want to use. I cannot reach the printer through the cable Internet. But, I have two network cards. How is it possible to use both networks at once? eth0 (static 192.168.1.254) is plugged into a four-port router, 192.168.1.1. On the public side of the four-port router is Internet provided by the cable company. I also have the classroom workstations plugged into a switch. The switch is plugged into the four-port router. The whole classroom is wired into the cable Internet. The other NIC, eth1, could it be plugged into an Ethernet jack in the wall? It uses the school network, and I might receive by DHCP an IP address like 10.140.10.100, with the printer on maybe 10.120.50.10. I was thinking about installing the printer on the server so that it could be shared with the workstations. But how does this work? Can I just plug eth1 into the school network and access both LANs? Thanks for any insight

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• org.smslib port in use exception

  - by danar jabbar

  I am trying to create web application to send sms by gsm modem in JSP first I put destination mobile number and sms text in url and get by request.getparameter and first message sent with no problem but when send a message again by referenshing the same page i get this exception: org.smslib.GatewayException: Comm library exception: java.lang.RuntimeException: gnu.io.PortInUseException: org.smslib at org.smslib.modem.SerialModemDriver.connectPort(SerialModemDriver.java:102) at org.smslib.modem.AModemDriver.connect(AModemDriver.java:114) at org.smslib.modem.ModemGateway.startGateway(ModemGateway.java:189) at org.smslib.Service$1Starter.run(Service.java:276) I tried to stop gateway and stop service but no hope My code: public boolean sendMessage(String strMobileNo,String strSMSText) { try { OutboundMessage outboundMessage=new OutboundMessage(); SMS message=new SMS(); SerialModemGateway gateway = new SerialModemGateway("modem.com1", "COM12", 9600, "Huawie", "EF200"); gateway.setInbound(true); gateway.setOutbound(true); gateway.setSimPin("0000"); gateway.setSmscNumber("+9647701144010"); Service.getInstance().setOutboundMessageNotification(message); Service.getInstance().addGateway(gateway); Service.getInstance().startService(); outboundMessage.setText(strSMSText); outboundMessage.setRecipient(strMobileNo); outboundMessage.setEncoding(Message.MessageEncodings.ENCUCS2); //outboundMessage.setDeliveryDelay(5000); Service.getInstance().sendMessage(outboundMessage); System.out.println(outboundMessage); gateway.stopGateway(); Service.getInstance().stopService(); Thread.sleep(10000); return true; } catch (Exception e) { e.printStackTrace(); return false; } }

  Read the article

• Deployment of broadband network

  - by sthustfo

  Hi all, My query is related to broadband network deployment. I have a DSL modem connection provided by my operator. Now the DSL modem has a built-in NAT and DHCP server, hence it allocates IP addresses to any client devices (laptops, PC, mobile) that connect to it. However, the DSL modem also gets a public IP address X that is provisioned by the operator. My question is Whether this IP address X provisioned by operator is an IP address that is directly on the public Internet? Is it likely (practical scenario) that my broadband operator will put in one more NAT+DHCP server and provide IP addresses to all the modems within his broadband network. In this case, the IP addresses allotted to the modem devices will not be directly on the public Internet. Thanks in advance.

  Read the article

• Manage multiple UDP calls

  - by rayman

  Hi all, I would like to have an advice for this issue: I am using Jbos 5.1.0, EJB3.0 I have system, which sending requests via UDP'S to remote modems, and suppose to wait for an answer from the target modem. the remote modems support only UDP calls, therefor I o design asynchronous mechanism. (also coz I want to request X modems parallel) this is what I try to do: all calls are retrieved from Data Base, then each call will be added as a message to JMS QUE. let's say i will set X MDB'S on that que, so I can work asynchronous. now each MDB will send UDP request to the IP-address(remote modem) which will be parsed from the que message. so basicly each MDB, which takes a message is sending a udp request to the remote modem and [b]waiting [/b]for an answer from that modem. [u]now here is the BUG:[/u] could happen a scenario where MDB will get an answer, but not from the right modem( which it requested in first place). that bad scenario cause two wrong things: a. the sender which sent the message will wait forever since the message never returned to him(it got accepted by another MDB). b. the MDB which received the message is not the right one, and probablly if it was on a "listener" mode, then it supposed to wait for an answer from diffrent sender.(else it wouldnt get any messages) so ofcourse I can handle everything with a RETRY mechanisem. so both mdb's(the one who got message from the wrong sender, and the one who never got the answer) will try again, to do thire operation with a hope that next time it will success. This is the mechanism, mybe you could tell me if there is any design pattren, or any other effective solution for this problem? Thanks, ray.

  Read the article

• Fake serial communication under Linux

  - by kigurai

  I have an application where I want to simulate the connection between a device and a "modem". The device will be connected to a serial port and will talk to the software modem through that. For testing purposes I want to be able to use a mock software device to test send and receive data. Example Python code device = Device() modem = Modem() device.connect(modem) device.write("Hello") modem_reply = device.read() Now, in my final app I will just pass /dev/ttyS1 or COM1 or whatever for the application to use. But how can I do this in software? I am running Linux and application is written in Python. I have tried making a FIFO (mkfifo ~/my_fifo) and that does work, but then I'll need one FIFO for writing and one for reading. What I want is to open ~/my_fake_serial_port and read and write to that. I have also lpayed with the ptymodule, but can't get that to work either. I can get a master and slave file descriptor from pty.openpty() but trying to read or write to them only causes IOError Bad File Descriptor error message.

  Read the article

• HDMI video connection cuts top and bottom borders of screen

  - by Luis Alvarado

  Ok this is an extension of another problem I had with a VGA connection and an Nvidia Geforce GT 440 card. Here is goes the explanation of this particular problem: I have a Soneview 32' TV. This TV has many connections including VGA (First reason I bought it), HDMI (Second reason but did not have a HDMI cable at that time) and DVI. I have had this TV for little over a month now, actually I had it to celebrate the release of Ubuntu 11.10 and started using it exactly on that date (I know too much fan there but hey, I like geek stuff). I started using it with the VGA cable. After 2 weeks I bought an Nvidia GT440 card. The previous 9500GT was working correctly with no problems whatsoever. I installed the GT440 and the first problem that I encountered using this latest card is mentioned here: Nvidia GT 440 black screen problem when loading lightdm greeter. The solution to this problem was to actually disconnect then connect again the VGA cable. This would result in the screen showing me the lightdm screen for my login. If I did not disconnect then connect the cable I could be there forever thinking that there is no video signal. I got tired of looking for answers that did not work and for solutions that made me literally have to install Ubuntu again. I just went and bought a HDMI cable and changed the VGA one for that one. It worked and I did not have to disconnect/connect the cable but now I have this problem when using any resolution. My normal resolution is 1920x1080 (This TV is 1080HD) so in VGA I could use this resolution with no problem, but on HDMI am getting the borders cut out. Here is a pic: As you can see from the PIC, the Launcher icons only show less than 50% of their witdh. Forget about the top and bottom parts, I can access them with the mouse but I can not visualize them in the screen. It is like it's outside of the TVs view. Basically there is like 20 to 30 pixels gone from all sides. I searched around and came to running xrand --verbose to see what it could detect from the TV. I got this: cyrex@cyrex:~$ xrandr --verbose xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 175, current 1920 x 1080, maximum 1920 x 1080 default connected 1920x1080+0+0 (0x164) normal (normal) 0mm x 0mm Identifier: 0x163 Timestamp: 465485 Subpixel: unknown Clones: CRTC: 0 CRTCs: 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: 1920x1080 (0x164) 103.7MHz *current h: width 1920 start 0 end 0 total 1920 skew 0 clock 54.0KHz v: height 1080 start 0 end 0 total 1080 clock 50.0Hz 1920x1080 (0x165) 105.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 55.1KHz v: height 1080 start 0 end 0 total 1080 clock 51.0Hz 1920x1080 (0x166) 107.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 56.2KHz v: height 1080 start 0 end 0 total 1080 clock 52.0Hz 1920x1080 (0x167) 109.9MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 57.2KHz v: height 1080 start 0 end 0 total 1080 clock 53.0Hz 1920x1080 (0x168) 112.0MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 58.3KHz v: height 1080 start 0 end 0 total 1080 clock 54.0Hz 1920x1080 (0x169) 114.0MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 59.4KHz v: height 1080 start 0 end 0 total 1080 clock 55.0Hz 1680x1050 (0x16a) 98.8MHz h: width 1680 start 0 end 0 total 1680 skew 0 clock 58.8KHz v: height 1050 start 0 end 0 total 1050 clock 56.0Hz 1680x1050 (0x16b) 100.5MHz h: width 1680 start 0 end 0 total 1680 skew 0 clock 59.9KHz v: height 1050 start 0 end 0 total 1050 clock 57.0Hz 1600x1024 (0x16c) 95.0MHz h: width 1600 start 0 end 0 total 1600 skew 0 clock 59.4KHz v: height 1024 start 0 end 0 total 1024 clock 58.0Hz 1440x900 (0x16d) 76.5MHz h: width 1440 start 0 end 0 total 1440 skew 0 clock 53.1KHz v: height 900 start 0 end 0 total 900 clock 59.0Hz 1360x768 (0x171) 65.8MHz h: width 1360 start 0 end 0 total 1360 skew 0 clock 48.4KHz v: height 768 start 0 end 0 total 768 clock 63.0Hz 1360x768 (0x172) 66.8MHz h: width 1360 start 0 end 0 total 1360 skew 0 clock 49.2KHz v: height 768 start 0 end 0 total 768 clock 64.0Hz 1280x1024 (0x173) 85.2MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 66.6KHz v: height 1024 start 0 end 0 total 1024 clock 65.0Hz 1280x960 (0x176) 83.6MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 65.3KHz v: height 960 start 0 end 0 total 960 clock 68.0Hz 1280x960 (0x177) 84.8MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 66.2KHz v: height 960 start 0 end 0 total 960 clock 69.0Hz 1280x720 (0x178) 64.5MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 50.4KHz v: height 720 start 0 end 0 total 720 clock 70.0Hz 1280x720 (0x179) 65.4MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 51.1KHz v: height 720 start 0 end 0 total 720 clock 71.0Hz 1280x720 (0x17a) 66.4MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 51.8KHz v: height 720 start 0 end 0 total 720 clock 72.0Hz 1152x864 (0x17b) 72.7MHz h: width 1152 start 0 end 0 total 1152 skew 0 clock 63.1KHz v: height 864 start 0 end 0 total 864 clock 73.0Hz 1152x864 (0x17c) 73.7MHz h: width 1152 start 0 end 0 total 1152 skew 0 clock 63.9KHz v: height 864 start 0 end 0 total 864 clock 74.0Hz ....Many Resolutions later... 320x200 (0x1d1) 10.2MHz h: width 320 start 0 end 0 total 320 skew 0 clock 31.8KHz v: height 200 start 0 end 0 total 200 clock 159.0Hz 320x175 (0x1d2) 9.0MHz h: width 320 start 0 end 0 total 320 skew 0 clock 28.0KHz v: height 175 start 0 end 0 total 175 clock 160.0Hz 1920x1080 (0x1dd) 333.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 173.9KHz v: height 1080 start 0 end 0 total 1080 clock 161.0Hz If it helps, the Refresh Rate at 1920x1080 is 60. There is a flickering effect at this resolution using HDMI but not VGA which I imagine is related to the borders cut off issue am asking here. I have also done the following but this will only solve the problem on lower resolutions than 1920x1080 or on others TV (My father has a Sony TV where this problem is also solved): NVIDIA WAY Go to Nvidia-Settings and there will be an option that will have more features if a HDMI cable is connected. In the next pic the option is DFP-1 (CNDLCD) but this name changes depending on what device the PC is connected to: Uncheck Force Full GPU Scaling What this will do for resolutions LOWER than 1920x1080 (At least in my case) is solve the flickering problem and fix the borders cut by the monitor. Save to Xorg.conf file the changes made after changing to a resolution acceptable to your eyes. TV WAY If you TV has OSD Menu and this menu has options for scanning the screen resolution or auto adjusting to it, disable them. Specifically the option about SCAN. If you have an option for AV Mode disable it. Basically disable any option that needs to scan and scale the resolution. Test one by one. In the case of my father's TV this did it. In my case, the Nvidia solved it for lower resolutions. NOTE: In the case this is not solved in the next couple of weeks I will add this as the answer but take into consideration that the issue is still active with 1920x1080 resolutions.

  Read the article

• Repurpose a Wire Basket as a Game Controller Organizer

  - by Jason Fitzpatrick

  If you’re looking for an easy way to organize your console controllers, this simple repurposing hack turns an IKEA wire basket intended for managing cable clutter into a game controller stand. You won’t need a Dremel tool to install this hack; all you need to do to follow in the foot steps of IKEAHackers reader Leslie is to install a SIGNUM cable basket (or similar cable organizer) upside down so loom curves up instead of down. Instant wire cradle for your controllers (or possibly an open air charging station for your small electronics). Check out the link below for more details. Game Controller Management System [IKEAHackers] How To Make a Youtube Video Into an Animated GIFHTG Explains: What Are Character Encodings and How Do They Differ?How To Make Disposable Sleeves for Your In-Ear Monitors

  Read the article

• Expensive HDMI Cables Make No Difference

  - by Jason Fitzpatrick

  While we’re no strangers to spreading the news that expensive HDMI cables are a ripoff, we’re happy to share yet another study that shows there’s zero difference between a $5 cable and a $95 one. Over at the British hardware review site Expert Reviews, they subjected a wide selection of HDMI cables to extensive tests in a bid to produce the end-all examination of whether or not a premium HDMI cable could actually produce a better signal. They used capture cards, pixel-by-pixel comparison of output, and other techniques to pick over individual frames until they ultimately reached the same conclusion everyone outside of the Monster sales staff had already reached: you’re getting absolutely no benefit to spending $100 on cable that can be had for under five bucks. Hit up the link below to read over their methodology. Expensive Cables Make Absolutely No Difference [via Geek News Central] HTG Explains: What Is RSS and How Can I Benefit From Using It? HTG Explains: Why You Only Have to Wipe a Disk Once to Erase It HTG Explains: Learn How Websites Are Tracking You Online

  Read the article

• How to avoid HDD spin up at system start? (Ubuntu from SSD)

  - by Oliver

  Thanks to hdparm -B1 /dev/sdb my HDD does no longer spin up when powered up on boot. But after completing the BIOS POST messages and starting Ubuntu the HDD gets a signal over the SATA data cable and spins up. Leaving the data cable (but still with plugged in SATA power cable) let the system boot up completely from my SSD without spinning up the HDD. What causes the HDD to spin up? Maybe Grub2? Edit: nope, doesn't seem to be Grub2 that spins up the drive. I just set up Grub to show its menu without timer. Nothings happens until I hit the Ubuntu standard boot option, then a few seconds later the drive spins up.

  Read the article

• How Fiber Optic Cables Are Made and Laid Across the Sea [Science]

  - by Jason Fitzpatrick

  We don’t know about you but yesterday’s video about how fiber optic cables work just made us more curious. Check out how the cables are made and laid across the sea. In the above video we see how fiber optic strands are manufactured, including how the draw tower mentioned in yesterday’s video works. Once the strands are manufactured, where do they go and how are they used? In the video below we see Alcatel-Lucent’s Ile de Sein, one of the largest and most powerful cable laying ships in the world. Check out the video to see cable storage wells that look like small stadiums. Finding out how the cables are made and what kind of planning and machinery it takes to lay them across the ocean is just as interesting as how they work. How It’s Made: Fiber Optics [YouTube] Undersea Cable [YouTube] What is a Histogram, and How Can I Use it to Improve My Photos?How To Easily Access Your Home Network From Anywhere With DDNSHow To Recover After Your Email Password Is Compromised

  Read the article

• How to run a local and external website on same computer with 2 NIC's, 2 Routers and 3 seperate networks?

  - by CandN

  Hello and hopefully I can get some answers to my question, though I think I'm making it more complicated for myself than it has to be. My business is a used auto dealership, and I'm in the process of connecting it to the world - via ethernet from the business server [running Xubuntu] to the ISP's ethernet router/modem, so that I can host our own website (no more than 5-10 people probably visiting at any time - mainly paying their bill), as well as set up a web based internal-intranet site - via DD-WRT Router on the 2nd NIC on the business server - that'll be accessed over Wifi from employees personal devices. On the other end of this is trying to offer free wifi to customers that is completely seperate of the 2 mentioned above networks. Quick Rundown: 1. Web Site for Customers to access. I'm going to use no-ip.org for DNS for the moment being, so I'll have a site that customers can access from anywhere in the world at "mybiz.no-ip.org". This will be forwarded to NIC #1 on the server, possibly at an address like "108.69.." as its being provided an IP from the ISP's modem/router, that is from Time Warner, and they allow NO! configuration options. Web Site for employees to access. I'm trying not to use the server too much as a desktop, only for critical situations, so having a backend thats seperate from the front-facing website is critical. This will be the DD-WRT router hardwired into NIC #2 on the server. This WiFi will be password accessible. Public WiFi for customers. The DD-WRT can seperate networks if I'm correct, I just can't seem to understand how to seperate the 2 and still have internet access on both. I've done it before, but the "Public" wifi (with no password set to connect) kept dropping the connection like a problem was happening that I couldn't figure out. So if I could do a little drawing, this is how it would/should possibly look. ISP -- [Sends Public Facing IP of 108.69.*.1/8] -- ISP Modem Router ISP Modem Router (Ethernet Only) -- [Gives Private IP 108.69.*.2] -- Server NIC #1 Server NIC #1 -- [Gives Private IP 108.69.*.3] -- DD-WRT Router DD-WRT Router -- [DHCP Enabled Giving IP's 172.16.0.0/16] -- Employees Network | | --------- [DHCP Enabled Giving IP's 192.168.1.0/24] -- Public WIFI Hope it's not too confusing, but it anyone could give me some good direct tutorials on how to accomplish this, or if YOU know, then it'll be alot of help. Thanks to all in advance. Need anything else to be explained? Don't hesitate to ask! *Using The LAMP stack with Webmin/VirtualMin -Customer site is located in /var/www2/ -Private Employees site is located in /var/www/ Using no-ip.org's dynamic client updater

  Read the article

• Network setup not working. Can't connect to the Internet in Ubuntu

  - by Clint Eastwood

  I want to know how to set-up network in 12.04 using automatic settings (DHCP). I installed Ubuntu, but I can't seen to see the network connection. What can I do? My notebook has no wireless only cable. The cable will not fit in. How can I plug it in? Do I need a special Cable? There is no router can I fix this myself, or should I call a technician? Also can I use USB to connect to the network/Internet? please can you help Thank you jamel

  Read the article

• How to solve dual monitor issue, which happens only during X start?

  - by tamashumi

  When is loading and two monitors are connected, instead of a login screen I see this: ...after clicking OK, selection appears: Then I'm following to console login, disconnecting by hand the secondary monitor cable, restart lightdm with a command sudo service lightdm restart ...and voila! System loads fine. If I disconnect the cable before boot X will be loaded fine too. It's not a nice 'feature' when I have to disconnect the cable each boot or X restart. I was trying to delete monitors.xml but it didn't help. The situation relates to my notebook with Intel integrated GPU. The same happens on two different pairs of monitors: at the office and at home. How can I fix this? Ubuntu 12.04 x64 Desktop with default Unity GUI.

  Read the article

• Using an iPad or Nexus 7 as an Ubuntu Second Monitor

  - by never4getthis

  Is there any way to use an iPad mini or a Nexus 7 as a second monitor through a cable? I dont want something like vnc, I need it to work through the usb cable (or any other cable). I imagine that the iPad will get a lot of hate around here, the reason why I am considering it is because of the larger screen (compared to the nexus 7). I think its self explanatory that I need this to work with ubuntu (as I am posting in this formum). Thanks for reading this highly unorganized, typo-flled (<--see what I did there?), un-cohesive post. Any help will be appreciated!

  Read the article

• Is there another application like Nokia PC Suite for Ubuntu?

  - by gabiro

  I've been looking for an alternative Nokia PC suite for Ubuntu. I'm tired of switching OS, and I'm tired of using Windows it is so boring me. Not Wammu, Gammu, Nokuntu, Ginokki and Series 60. They don't work. Via cable. I need an application that can detect via cable (because I have a very different reason why I need it to detect via cable). Also after installing in Wine it can't detect the Phone and I think the installation didn't finish correctly. Thank You !

  Read the article

• How can I minimize the amount my router slows down my Internet connection speed?

  - by Lord Torgamus

  Background I'm working with what I assume is a pretty common Internet setup: a cable modem, a wireless router and a few Internet-connected devices. Lately, I've started being more demanding on my Internet connection, and noticed that using my router slows down my download speeds considerably. I just kind of dealt with it until Zune Marketplace on the Xbox 360 told me that a movie was going to take well over ten hours to download, and I just didn't want to wait that long. Good little scientist that I am, I tried to reduce the problem down to one variable. The test As a control, I turned off all the devices in the house that use wireless Internet, and unplugged all the wired devices except for the Xbox. I also power-cycled both the modem and the router. I then tried to download the movie again, and was told that it would still take over ten hours. Next, I unplugged the router, and connected the Xbox directly to the modem. The movie downloaded in just over one hour. As far as I can tell, this means that my ISP, other cable users near me, the remote servers, anything wireless-related and my machines' disk speeds can't be at fault. A similar experiment that replaced the Xbox with a wired laptop produced similar results. To me, this says "the router is responsible for things taking around ten times longer to download." My question I'd still prefer to use the router for a few reasons: it's a pain to connect and disconnect everything every time there's a big file to download direct connection to the modem isn't good for security only one machine can be connected directly to the modem at a time What can I do to have fast connection speeds while still using the router? I don't mind turning other machines off, as long as I don't have to mess with power and ethernet cables. EDIT : After asking this followup question and then this one, I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant. I know this isn't an answer — which is why I'm not posting it as an answer — but it is how I resolved the situation, and hopefully it'll be helpful for someone.

  Read the article

• Laptop battery sometimes does not charge?

  - by user1880405

  So on my Asus K56C laptop running Ubuntu 14.04 (was same problem in 13.10) I got a problem that from time to time after I use laptop without cable (just on battery) it stops charging with cable. I can still use laptop indefinitely on cable, but it's not charging. The only solution is to remove and reinsert the battery, then it will charge. Now I wonder how does laptop 'knows' that battery was reinserted, and is it possible to simulate that from Ubuntu, maybe some command which refreshes battery? P.s.: this is not happening on Windows 8.1.

  Read the article

• Verizon 4G LTE vs. a LAN

  - by n8wrl

  I have been having quite a bit of trouble getting my new Verizon 4G-LTE service running on a Windows 7 desktop. My desktop is on a LAN here at home with two other PC's. We all share printers, files, media, etc. Until yesterday, we also shared a Verizon 3G modem via a NetGear 3G broadband WAP. That isn't compatible with the 4G so now I am just trying to get the 4G modem working directly connected to one of the desktops. After some USB wrangling, it seems to work. Except, every 7-10 minutes the connection would drop. After some time on the phone with a very nice Verizon technician, it seems to be staying up - it's been up for 20 minutes now. He told me that my LAN was causing the 4G to drop. That traffic on my LAN, even though it is not destined for the internet (ICS not working yet) was causing the cell tower to detect an 'IP change' and a 'security violation' in my modem and drop my connection. Is this Verizon's way of forbidding more than one computer to share a modem? I have my computer running now without a LAN connection and the 4G is still up. But this isn't practical. Has anyone heard of this?

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• Name resolution for the name <name> timed out after none of the configured DNS servers responded.

  - by Paul Brown

  Installed Windows 7 (previously ran XP and Vista with no problems) a couple of weeks ago and I'm at least once a day getting the above error show up in the event logs and losing all internet connection. The only current way to resolve it is to reboot my cable modem. My ISP have been running diagnostics on it and tell me there is no problem whatsoever. I've configured my router (and PC on occasion) to point at OpenDNS - still occurs. I've had the PC directly connected to the modem - still occurs. If I can give more info that might of use please ask thanks Update: After moaning at my ISP for a couple of weeks (VirginMedia) they agreed to send me out a new cable modem ... and I've not had the issue since.

  Read the article

• Juniper SSG-5 subinterface vlan routing to the internet

  - by catfish

  I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• Networking Logs for MAC Addresses

  - by NetworkGuy

  I wanted to ask a multi-part question. Does Comcast Cable Internet services record MAC Addresses of the Router behind the cable modem. I know they record it for the modem itself. But is there a way for the Modem/Comcast to relay and keep logs of the MAC ID of the Router itself? Then does a windows operating system Log the MAC ID of the Router when its connected to it? If so where do I locate and purge this? Please let me know all areas where it is Logged within the operating system. Thank you!

  Read the article

• Setting up Dynamic DNS for Wireless Cameras And Accessing them Remotely

  - by Mike Szp.

  I've been trying to set up two TP LINK wireless N cameras that I bought so that I can see them remotely. I've set it up so that each has it's own ip address (192...105/192...106) and I can access them if I type that into the browser of a local computer The thing is that I don't know how to access them from another remote PC. My current setup is a a each camera connected to the router which then connects to the modem. When I set up the Dynamic DNS, and I access the "webpage" for my IP through a remote computer, it just goes to the configuration page of the modem. I have no idea how to make it go to the router or to the cameras. the router has its own ip range of 192.168.1.x while the modem has 192.168.2.x To access the cameras I type into the web browser: 192.168.1.114:100 on the local computer but I have no idea how to get there through the webpage of my Dynamic DNS remotely.

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM [closed]

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >