Search Results

Search found 1299 results on 52 pages for 'peopletools 8 51'.

Page 27/52 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

  • Dell XPS 15 (L502x) sound problem

    - by lauramolenaar
    I have a problem with my sound on my Dell XPS 15. First, when I had Windows 7, my sound was pretty good (I have a JBL 2.1 speaker system with Waves Maxx audio), but since I installed Ubuntu 12.04 it sounded very cheap and as if I put my laptop in a tin can. I've already tried installing alsa-hda-dkms from the alsa-daily ppa (http://ppa.launchpad.net/ubuntu-audio-dev/alsa-daily) This is my audio controller: laura@laura-XPS-L502X:~$ lspci -v | grep -A7 -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04b6 Flags: bus master, fast devsel, latency 0, IRQ 51 Memory at f1c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel I hope you can help me, and you can always ask me for more information. Result of aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 Result of aplay -L: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC665 Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Digital IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=PCH,DEV=0 HDA Intel PCH, HDMI 0 HDMI Audio Output dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample mixing device dmix:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample mixing device dmix:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample snooping device dsnoop:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample snooping device dsnoop:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct hardware device without any conversions hw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct hardware device without any conversions hw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Hardware device with all software conversions plughw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Hardware device with all software conversions plughw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Hardware device with all software conversions

    Read the article

  • Cannot install vlc in ubuntu 13.10

    - by nisargshah95
    for some reasons I cannot instal VLC media player on my Ubuntu Gnome 13.10 32bit. I added the VideoLAN PPA repository and ran sudo apt-get update and sudo apt-get install vlc Here's the log - nisarg@nisarg-ThinkPad-T61:~$ sudo apt-get install vlc Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: liba52-0.7.4 libaacs0 libass4 libavcodec53 libavformat53 libavutil51 libbluray1 libcddb2 libcrystalhd3 libdc1394-22 libdca0 libdirac-encoder0 libdirectfb-1.2-9 libdvbpsi8 libdvdnav4 libdvdread4 libebml3 libfaad2 libgsm1 libiso9660-8 libkate1 libmad0 libmatroska5 libmodplug1 libmpcdec6 libmpeg2-4 libopus0 libpostproc52 libresid-builder0c2a libschroedinger-1.0-0 libsdl-image1.2 libsdl1.2debian libsidplay2 libssh2-1 libswscale2 libtar0 libts-0.0-0 libtwolame0 libupnp6 libva-x11-1 libva1 libvcdinfo0 libvlc5 libvlccore5 libwebp4 libx264-123 libxcb-composite0 libxcb-keysyms1 libxcb-randr0 libxcb-xv0 libzvbi-common libzvbi0 tsconf vlc-data vlc-nox vlc-plugin-notify vlc-plugin-pulse Suggested packages: libbluray-bdj firmware-crystalhd libdvdcss2 debhelper opus-tools videolan-doc The following NEW packages will be installed: liba52-0.7.4 libaacs0 libass4 libavcodec53 libavformat53 libavutil51 libbluray1 libcddb2 libcrystalhd3 libdc1394-22 libdca0 libdirac-encoder0 libdirectfb-1.2-9 libdvbpsi8 libdvdnav4 libdvdread4 libebml3 libfaad2 libgsm1 libiso9660-8 libkate1 libmad0 libmatroska5 libmodplug1 libmpcdec6 libmpeg2-4 libopus0 libpostproc52 libresid-builder0c2a libschroedinger-1.0-0 libsdl-image1.2 libsdl1.2debian libsidplay2 libssh2-1 libswscale2 libtar0 libts-0.0-0 libtwolame0 libupnp6 libva-x11-1 libva1 libvcdinfo0 libvlc5 libvlccore5 libwebp4 libx264-123 libxcb-composite0 libxcb-keysyms1 libxcb-randr0 libxcb-xv0 libzvbi-common libzvbi0 tsconf vlc vlc-data vlc-nox vlc-plugin-notify vlc-plugin-pulse 0 upgraded, 58 newly installed, 0 to remove and 7 not upgraded. Need to get 16.7 MB of archives. After this operation, 75.0 MB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main vlc-data all 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [4,967 kB] Get:2 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main libvlccore5 i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [384 kB] Get:3 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main libvlc5 i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [42.4 kB] Get:4 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main vlc-nox i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [2,084 kB] Get:5 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main vlc i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [1,078 kB] Get:6 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main vlc-plugin-notify i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [5,836 B] Get:7 http://ppa.launchpad.net/videolan/stable-daily/ubuntu/ saucy/main vlc-plugin-pulse i386 2.0.8+git20131025+r620-0~r13~ubuntu13.10.1 [18.2 kB] Err http://archive.ubuntu.com/ubuntu/ saucy/universe libaacs0 i386 0.6.0-2 Connection failed [IP: 91.189.92.176 80] 51% [Waiting for headers] Now it doesn't move forward after this point. Any suggestions?

    Read the article

  • SharePoint 2010 Field Expression Builder

    - by Ricardo Peres
    OK, back to two of my favorite topics, expression builders and SharePoint. This time I wanted to be able to retrieve a field value from the current page declaratively on the markup so that I can assign it to some control’s property, without the need for writing code. Of course, the most straight way to do it is through an expression builder. Here’s the code: 1: [ExpressionPrefix("SPField")] 2: public class SPFieldExpressionBuilder : ExpressionBuilder 3: { 4: #region Public static methods 5: public static Object GetFieldValue(String fieldName, PropertyInfo propertyInfo) 6: { 7: Object fieldValue = SPContext.Current.ListItem[fieldName]; 8:  9: if (fieldValue != null) 10: { 11: if ((fieldValue is IConvertible) && (typeof(IConvertible).IsAssignableFrom(propertyInfo.PropertyType) == true)) 12: { 13: if (propertyInfo.PropertyType.IsAssignableFrom(fieldValue.GetType()) != true) 14: { 15: fieldValue = Convert.ChangeType(fieldValue, propertyInfo.PropertyType); 16: } 17: } 18: } 19:  20: return (fieldValue); 21: } 22:  23: #endregion 24:  25: #region Public override methods 26: public override Object EvaluateExpression(Object target, BoundPropertyEntry entry, Object parsedData, ExpressionBuilderContext context) 27: { 28: return (GetFieldValue(entry.Expression, entry.PropertyInfo)); 29: } 30:  31: public override CodeExpression GetCodeExpression(BoundPropertyEntry entry, Object parsedData, ExpressionBuilderContext context) 32: { 33: if (String.IsNullOrEmpty(entry.Expression) == true) 34: { 35: return (new CodePrimitiveExpression(String.Empty)); 36: } 37: else 38: { 39: return (new CodeMethodInvokeExpression(new CodeMethodReferenceExpression(new CodeTypeReferenceExpression(this.GetType()), "GetFieldValue"), new CodePrimitiveExpression(entry.Expression), new CodePropertyReferenceExpression(new CodeArgumentReferenceExpression("entry"), "PropertyInfo"))); 40: } 41: } 42:  43: #endregion 44:  45: #region Public override properties 46: public override Boolean SupportsEvaluate 47: { 48: get 49: { 50: return (true); 51: } 52: } 53: #endregion 54: } You will notice that it will even try to convert the field value to the target property’s type, through the use of the IConvertible interface and the Convert.ChangeType method. It must be placed on the Global Assembly Cache or you will get a security-related exception. The other alternative is to change the trust level of your web application to full trust. Here’s how to register it on Web.config: 1: <expressionBuilders> 2: <!-- ... --> 3: <add expressionPrefix="SPField" type="MyNamespace.SPFieldExpressionBuilder, MyAssembly, Culture=neutral, Version=1.0.0.0, PublicKeyToken=29186a6b9e7b779f" /> 4: </expressionBuilders> And finally, here’s how to use it on an ASPX or ASCX file inside a publishing page: 1: <asp:Label runat="server" Text="<%$ SPField:Title %>"/>

    Read the article

  • Trouble compiling MonoDevelop 4 on Ubuntu 12.04

    - by Mehran
    I'm trying to compile the latest version of MonoDevelop (4.0.9) on my Ubuntu 12.04 and I'm facing errors I can not overcome. Here are my machine's configurations: OS: Ubuntu 12.04 64-bit Mono: version 3.0.12 And here are the commands that I ran to download MonoDevelop: $ git clone git://github.com/mono/monodevelop.git $ cd monodevelop $ git submodule init $ git submodule update And afterwards to compile: ./configure --prefix=`pkg-config --variable=prefix mono` --profile=stable make Then I faced the following errors (sorry if it's long): ... Building ./Main.sln xbuild /verbosity:quiet /nologo /property:CodePage=65001 ./Main.sln /property:Configuration=Debug /home/mehran/git/monodevelop/main/Main.sln: warning : Don't know how to handle GlobalSection MonoDevelopProperties.Debug, Ignoring. : warning CS1685: The predefined type `System.Runtime.CompilerServices.ExtensionAttribute' is defined in multiple assemblies. Using definition from `mscorlib' /usr/lib/mono/4.0/Microsoft.CSharp.targets: error : Compiler crashed with code: 1. : warning CS1685: The predefined type `System.Runtime.CompilerServices.ExtensionAttribute' is defined in multiple assemblies. Using definition from `mscorlib' Editor/IDocument.cs(98,30): warning CS0419: Ambiguous reference in cref attribute `GetOffset'. Assuming `ICSharpCode.NRefactory.Editor.IDocument.GetOffset(int, int)' but other overloads including `ICSharpCode.NRefactory.Editor.IDocument.GetOffset(ICSharpCode.NRefactory.TextLocation)' have also matched PatternMatching/INode.cs(51,37): warning CS1574: XML comment on `ICSharpCode.NRefactory.PatternMatching.PatternExtensions.Match(this ICSharpCode.NRefactory.PatternMatching.INode, ICSharpCode.NRefactory.PatternMatching.INode)' has cref attribute `PatternMatching.Match.Success' that could not be resolved TextLocation.cs(35,23): warning CS0419: Ambiguous reference in cref attribute `Editor.IDocument.GetOffset'. Assuming `ICSharpCode.NRefactory.Editor.IDocument.GetOffset(int, int)' but other overloads including `ICSharpCode.NRefactory.Editor.IDocument.GetOffset(ICSharpCode.NRefactory.TextLocation)' have also matched TypeSystem/FullTypeName.cs(87,24): warning CS0419: Ambiguous reference in cref attribute `ReflectionHelper.ParseReflectionName'. Assuming `ICSharpCode.NRefactory.TypeSystem.ReflectionHelper.ParseReflectionName(string)' but other overloads including `ICSharpCode.NRefactory.TypeSystem.ReflectionHelper.ParseReflectionName(string, ref int)' have also matched TypeSystem/INamedElement.cs(59,24): warning CS0419: Ambiguous reference in cref attribute `ReflectionHelper.ParseReflectionName'. Assuming `ICSharpCode.NRefactory.TypeSystem.ReflectionHelper.ParseReflectionName(string)' but other overloads including `ICSharpCode.NRefactory.TypeSystem.ReflectionHelper.ParseReflectionName(string, ref int)' have also matched TypeSystem/IType.cs(50,26): warning CS1584: XML comment on `ICSharpCode.NRefactory.TypeSystem.IType' has syntactically incorrect cref attribute `IEquatable{IType}.Equals(IType)' TypeSystem/IType.cs(319,38): warning CS1580: Invalid type for parameter `1' in XML comment cref attribute `GetMethods(Predicate{IUnresolvedMethod}, GetMemberOptions)' TypeSystem/TypeKind.cs(61,17): warning CS1580: Invalid type for parameter `1' in XML comment cref attribute `IType.GetNestedTypes(Predicate{ITypeDefinition}, GetMemberOptions)' TypeSystem/SpecialType.cs(50,52): warning CS1580: Invalid type for parameter `1' in XML comment cref attribute `IType.GetNestedTypes(Predicate{ITypeDefinition}, GetMemberOptions)' /usr/lib/mono/4.0/Microsoft.CSharp.targets: error : Compiler crashed with code: 1.

    Read the article

  • Social Targeting: Who Do You Think You’re Talking To?

    - by Mike Stiles
    Are you the kind of person that tries to sell Clay Aiken CD’s outside Warped Tour concert venues? Then you don’t think a lot about targeting your messages to the right audience. For your communication to pack the biggest punch it can, you need to know where to throw it. And a recent study on social demographics might help you see social targeting in a whole new light. Pingdom’s annual survey of social network demographics shows us first of all that there is no gender difference between Facebook and Twitter. Both are 40% male, 60% female. If you’re looking for locales that lean heavily male, that would be Slashdot, Hacker News and Stack Overflow. The women are dominating Pinterest, Goodreads and Blogger. So what about age? 55% of tweeters are 35 and up, compared with 63% at Pinterest, 65% at Facebook and 70% at LinkedIn. As you can tell, LinkedIn supports the oldest user base, with the average member being 44. The average age at Facebook is 51, and it’s 37 at Twitter. If you want to aim younger, have you met Orkut yet? 83% of its users are under 35. The next sites in order as great candidates for the young market are deviantART, Hacker News, Hi5, Github, and Reddit. I know, other than Reddit, many of you might be saying “who?” But the list could offer an opportunity to look at the vast social world beyond Facebook, Twitter and Google+ (which Pingdom did not include in the survey at all due to a lack of accessible data). As for the average age of social users overall: 26% are 25-34 25% are 35-44 19% are 45-54 16% are 18-24  6% are 55-64  5% are 0-17  and 2% are 65 Now you know where you stand on the “cutting edge” scale for a person your age. You’re welcome. Certainly such demographics are a moving target and need to be watched and reassessed on a regular basis to make sure you’re moving in step with the people you want to talk to. For instance, since Pingdom’s survey last year, the age of the average Facebook user has gone up 2 years, while the age of the average Twitter user has gone down 2 years. With the targeting and analytics tools available on today’s social management platforms, there’s little need to market in the dark. Otherwise, good luck with those Clay CD’s.

    Read the article

  • Installing Age of Empires II using PlayOnLinux doesn't work?

    - by user70342
    I have tried installing age of empires 2 using PlayOnLinux, the installation appeared to go fine but when I try and open the game it says there is a serious fault. The error report is below, unfortunately this doesn't mean alot to me, I was wondering if you could help, a) By highlighting the problem and b) by suggesting a solution. Many Thanks Unhandled exception: page fault on read access to 0xffffffff in 32-bit code (0x0040aaad). Register dump: CS:0073 SS:007b DS:007b ES:007b FS:0033 GS:003b EIP:0040aaad ESP:0033fd00 EBP:0033fde4 EFLAGS:00010293( R- -- I S -A- -C) EAX:00000001 EBX:bde88d9d ECX:00000067 EDX:00400000 ESI:7b867c00 EDI:00400000 Stack dump: 0x0033fd00:00410fed 00000000 00400000 00000067 0x0033fd10:0041ab90 00130d8a 7b895848 7bc483b1 0x0033fd20:0044c800 00000002 0044bdd0 7bca4e6c 0x0033fd30:7bc3590f 00000800 00000094 00000005 0x0033fd40:00000000 00000893 00000002 76726553 0x0033fd50:20656369 6b636150 00003420 00000800 Backtrace: =0 0x0040aaad in empires2 (+0xaaad) (0x0033fde4) 1 0x0041ace2 in empires2 (+0x1ace1) (0x0033fe70) 2 0x7b85ac0c call_process_entry+0xb() in kernel32 (0x0033fe88) 3 0x7b85e13b in kernel32 (+0x4e13a) (0x0033fec8) 4 0x7bc714f0 call_thread_func_wrapper+0xb() in ntdll (0x0033fed8) 5 0x7bc7172d call_thread_func+0x7c() in ntdll (0x0033ffa8) 6 0x7bc714ce RtlRaiseException+0x21() in ntdll (0x0033ffc8) 7 0x7bc4c30e in ntdll (+0x3c30d) (0x0033ffe8) 0x0040aaad: pop %ss Modules: Module Address Debug info Name (51 modules) PE 400000- 44b000 Export empires2 PE 10000000-1000c000 Deferred drvmgt ELF 35cae000-35d24000 Deferred rpcrt4 -PE 35cc0000-35d24000 \ rpcrt4 ELF 68000000-68022000 Deferred ld-linux.so.2 ELF 68022000-681c7000 Deferred libc.so.6 ELF 681c7000-681cc000 Deferred libdl.so.2 ELF 681cc000-681f8000 Deferred libm.so.6 ELF 681f8000-68201000 Deferred libnss_compat.so.2 ELF 68201000-6821b000 Deferred libnsl.so.1 ELF 6821b000-68228000 Deferred libnss_files.so.2 ELF 68228000-68366000 Deferred user32 -PE 68240000-68366000 \ user32 ELF 68366000-68421000 Deferred gdi32 -PE 68370000-68421000 \ gdi32 ELF 68421000-68481000 Deferred advapi32 -PE 68430000-68481000 \ advapi32 ELF 68481000-68499000 Deferred version -PE 68490000-68499000 \ version ELF 68499000-68533000 Deferred libfreetype.so.6 ELF 68533000-68549000 Deferred libz.so.1 ELF 68549000-685db000 Deferred winex11 -PE 68550000-685db000 \ winex11 ELF 685db000-685e4000 Deferred libsm.so.6 ELF 685e4000-685fe000 Deferred libice.so.6 ELF 685fe000-68610000 Deferred libxext.so.6 ELF 68610000-68744000 Deferred libx11.so.6 ELF 68744000-6874a000 Deferred libuuid.so.1 ELF 6874a000-68751000 Deferred libxdmcp.so.6 ELF 68751000-68755000 Deferred libxinerama.so.1 ELF 68755000-6875b000 Deferred libxxf86vm.so.1 ELF 6875b000-68765000 Deferred libxrender.so.1 ELF 68765000-6876e000 Deferred libxrandr.so.2 ELF 6876e000-68772000 Deferred libxcomposite.so.1 ELF 68772000-68782000 Deferred libxi.so.6 ELF 68782000-687b6000 Deferred libfontconfig.so.1 ELF 687b6000-687e0000 Deferred libexpat.so.1 ELF 687e0000-687eb000 Deferred libxcursor.so.1 ELF 687eb000-687f1000 Deferred libxfixes.so.3 ELF 6f102000-6f10e000 Deferred libnss_nis.so.2 ELF 7194d000-7196e000 Deferred imm32 -PE 71950000-7196e000 \ imm32 ELF 72c76000-72db7000 Dwarf libwine.so.1 ELF 75d65000-75d86000 Deferred libxcb.so.1 ELF 79223000-79227000 Deferred libxau.so.6 ELF 7b800000-7b8f5000 Dwarf kernel32 -PE 7b810000-7b8f5000 \ kernel32 ELF 7bc00000-7bcc1000 Dwarf ntdll -PE 7bc10000-7bcc1000 \ ntdll ELF 7bf00000-7bf03000 Deferred ELF 7c708000-7c723000 Deferred libpthread.so.0 Threads: process tid prio (all id:s are in hex) 00000008 (D) C:\Program Files\Microsoft Games\Age of Empires II\empires2.exe 00000009 0 <== 0000000e services.exe 00000039 0 00000038 0 0000001f 0 00000019 0 00000018 0 00000017 0 00000015 0 00000010 0 0000000f 0 00000012 winedevice.exe 0000001e 0 0000001a 0 00000014 0 00000013 0 0000001b plugplay.exe 00000021 0 0000001d 0 0000001c 0 00000024 explorer.exe 00000025 0 00000035 winedevice.exe 0000003a 0 00000037 0 00000036 0 System information: Wine build: wine-1.4-rc1 Platform: i386 Host system: Linux Host version: 3.2.0-24-generic

    Read the article

  • Why does aptitude want to remove a bunch of files?

    - by Mediterran81
    Recently I encountered dependencies resolve issues when using APTITUDE (it is my favorite). Nevertheless, I started to feel that APTITUDE does not behave as it is supposed to be in 64 bits systems while apt-get works fine. Can someone confirm that APTITUDE is buggy in Ubuntu 11.10 amd64? Edit: For example, when tried to install ntfs-config using APTITUDE, it asked me to remove over 100 packages (skype for example), while using apt-get worked fine. han@L502X:~$ sudo aptitude install ntfs-config [sudo] password for han: The following NEW packages will be installed: ntfs-3g{ab} ntfs-config 0 packages upgraded, 2 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/640 kB of archives. After unpacking 2,466 kB will be used. The following packages have unmet dependencies: ntfs-3g: Conflicts: ntfsprogs but 2.0.0-1ubuntu4 is installed. The following actions will resolve these dependencies: Remove the following packages: 1) flashplugin-downloader 2) flashplugin-installer 3) libasound2 4) libasound2-plugins 5) libasyncns0 6) libatk1.0-0 7) libaudio2 8) libavahi-client3 9) libavahi-common3 10) libc6 11) libcairo2 12) libcomerr2 13) libcups2 14) libcurl3 15) libdatrie1 16) libdb5.1 17) libdbus-1-3 18) libdbusmenu-qt2 19) libexpat1 20) libffi6 21) libflac8 22) libfontconfig1 23) libfreetype6 24) libgcc1 25) libgcrypt11 26) libgdk-pixbuf2.0-0 27) libglib2.0-0 28) libgnutls26 29) libgpg-error0 30) libgssapi-krb5-2 31) libgtk2.0-0 32) libice6 33) libidn11 34) libjack-jackd2-0 35) libjasper1 36) libjpeg62 37) libjson0 38) libk5crypto3 39) libkeyutils1 40) libkrb5-3 41) libkrb5support0 42) liblcms1 43) libldap-2.4-2 44) libmng1 45) libnspr4 46) libnspr4-0d 47) libnss3 48) libnss3-1d 49) libogg0 50) libpango1.0-0 51) libpcre3 52) libpixman-1-0 53) libpng12-0 54) libpulse0 55) libqt4-dbus 56) libqt4-declarative 57) libqt4-network 58) libqt4-script 59) libqt4-sql 60) libqt4-xml 61) libqt4-xmlpatterns 62) libqtcore4 63) libqtgui4 64) librtmp0 65) libsamplerate0 66) libsasl2-2 67) libsasl2-modules 68) libselinux1 69) libsm6 70) libsndfile1 71) libspeexdsp1 72) libsqlite3-0 73) libssl1.0.0 74) libstdc++6 75) libtasn1-3 76) libthai0 77) libtiff4 78) libuuid1 79) libvorbis0a 80) libvorbisenc2 81) libwrap0 82) libx11-6 83) libxau6 84) libxcb-render0 85) libxcb-shm0 86) libxcb1 87) libxcomposite1 88) libxcursor1 89) libxdamage1 90) libxdmcp6 91) libxext6 92) libxfixes3 93) libxft2 94) libxi6 95) libxinerama1 96) libxrandr2 97) libxrender1 98) libxss1 99) libxt6 100) libxv1 101) nspluginviewer 102) nspluginwrapper 103) ntfsprogs 104) skype 105) sni-qt 106) zlib1g Leave the following dependencies unresolved: 107) flashplugin-downloader recommends libasound2-plugins (>= 1.0.16) Accept this solution? [Y/n/q/?]

    Read the article

  • SCVMM – Round 2 – How to create a Private Cloud using PowerShell

    - by Waclaw Chrabaszcz
    Originally posted on: http://geekswithblogs.net/Wchrabaszcz/archive/2013/06/28/scvmm--round-2--how-to-create-a-private.aspxHave you ever seen "A Bridge too far" movie? To not to wake up a click too far, it is good to script some tasks. Yes of course we can follow wizards, but some of us want to be warriorsJ. A small tip, take a look on credentials and system GUID examples. I don't know how about you, but for me it will be really useful in the future.    # credents$credential = Get-CredentialNew-SCRunAsAccount -Name "TESTDOMAIN\Administrator" -Credential $credential #storage $opsMgrServerCredential = Get-SCRunAsAccount -Name "TESTDOMAIN\Administrator"New-SCStorageClassification -Name "Bronze" -Description "" –RunAsynchronouslyNew-SCStorageClassification -Name "Silver" -Description "" –RunAsynchronouslyNew-SCStorageClassification -Name "Gold" -Description "" –RunAsynchronously # add a shared storageFind-SCComputer -ComputerName "dc.TESTDOMAIN.net"Add-SCStorageProvider -AddWindowsNativeWmiProvider -Name "dc.TESTDOMAIN.net" -RunAsAccount $opsMgrServerCredential -ComputerName "dc.TESTDOMAIN.net"$fileServer = Get-SCStorageFileServer "dc.TESTDOMAIN.net"$fileShares = @()$fileShares += Get-SCStorageFileShare -Name "VMMLibrary"Set-SCStorageFileServer -StorageFileServer $fileServer -AddStorageFileShareToManagement $fileShares –RunAsynchronously #fabric network$logicalNetwork = New-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" -LogicalNetworkDefinitionIsolation $false -EnableNetworkVirtualization $true -UseGRE $true -IsPVLAN $false$allHostGroups = @()$allHostGroups += Get-SCVMHostGroup -Name "All Hosts"$allSubnetVlan = @()$allSubnetVlan += New-SCSubnetVLan -Subnet "10.0.0.0/24" -VLanID 0New-SCLogicalNetworkDefinition -Name "TESTDOMAIN-Service-Network_0" -LogicalNetwork $logicalNetwork -VMHostGroup $allHostGroups -SubnetVLan $allSubnetVlan #IP pool$logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network"$logicalNetworkDefinition = Get-SCLogicalNetworkDefinition -LogicalNetwork $logicalNetwork -Name "TESTDOMAIN-Service-Network_0" # Gateways$allGateways = @()$allGateways += New-SCDefaultGateway -IPAddress "10.0.0.1" –Automatic# DNS servers $allDnsServer = @("10.0.0.1")# DNS suffixes$allDnsSuffixes = @("TESTDOMAIN.net")# WINS servers$allWinsServers = @()New-SCStaticIPAddressPool -Name "TESTDOMAIN-Service-Network" -LogicalNetworkDefinition $logicalNetworkDefinition -Subnet "10.0.0.0/24" -IPAddressRangeStart "10.0.0.51" -IPAddressRangeEnd "10.0.0.75" -DefaultGateway $allGateways -DNSServer $allDnsServer -DNSSuffix "" -DNSSearchSuffix $allDnsSuffixes –RunAsynchronously #Hyper-V Virtual Networks$logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" $vmNetwork = New-SCVMNetwork -Name "TESTDOMAIN-VMN" -LogicalNetwork $logicalNetwork -IsolationType "WindowsNetworkVirtualization" -CAIPAddressPoolType "IPV4" -PAIPAddressPoolType "IPV4"Write-Output $vmNetwork$subnet = New-SCSubnetVLan -Subnet "10.0.0.0/24"New-SCVMSubnet -Name "Con-SN" -VMNetwork $vmNetwork -SubnetVLan $subnet # bind VLAN with the Network Adapter$vmHost = Get-SCVMHost -ComputerName "VMM01.TESTDOMAIN.net"$vmHostNetworkAdapter = Get-SCVMHostNetworkAdapter -VMHost $vmHost #-Name "Intel 21140-Based PCI Fast Ethernet Adapter (Emulated)"Set-SCVMHostNetworkAdapter -VMHostNetworkAdapter $vmHostNetworkAdapter -Description "" -AvailableForPlacement $true -UsedForManagement $true $logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" Set-SCVMHostNetworkAdapter -VMHostNetworkAdapter $vmHostNetworkAdapter -AddOrSetLogicalNetwork $logicalNetworkSet-SCVMHost -VMHost $vmHost -RunAsynchronously -NumaSpanningEnabled $true #Create a Private Cloud$Guid = [System.Guid]::NewGuid()Set-SCCloudCapacity -JobGroup $Guid -UseCustomQuotaCountMaximum $false -UseMemoryMBMaximum $false -UseCPUCountMaximum $false -UseStorageGBMaximum $false -UseVMCountMaximum $false -CustomQuotaCount 10 -MemoryMB 10240 -CPUCount 10 -StorageGB 386 -VMCount 10$resources = @()$resources += Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network"$resources += Get-SCLoadBalancer -Manufacturer "Microsoft"$readonlyLibraryShares = @()$readonlyLibraryShares += Get-SCLibraryShare | where { $_.LibraryServer.Name -eq "dc.TESTDOMAIN.net" -and $_.Name -eq "VMMLibrary" }$addCapabilityProfiles = @()$addCapabilityProfiles += Get-SCCapabilityProfile -Name "Hyper-V"$Guid2 = [System.Guid]::NewGuid()Set-SCCloud -JobGroup $Guid2 -RunAsynchronously -AddCloudResource $resources -AddReadOnlyLibraryShare $readonlyLibraryShares -AddCapabilityProfile $addCapabilityProfiles$hostGroups = @()$hostGroups += Get-SCVMHostGroup -Name "TESTDOMAIN"New-SCCloud -VMHostGroup $hostGroups -Name "TESTDOMAIN-Cloud" -Description "" –RunAsynchronously

    Read the article

  • 2013 EC Elections Results

    - by Heather VanCura
    The 2013 Fall Executive Committee (EC) Elections process is now complete.  Congratulations to the following JCP Members as the new and re-elected EC Members!   We had a slight increase in JCP Member voter turnout at ~25% (up from 24% in 2012).  All Ratified candidates and the top eight Elected candidates were elected by the JCP Membership.  As part of the transition to a merged EC, Members elected in 2013 are ranked to determine whether their initial term will be one or two years. The 50% of Ratified and 50% of Elected members who receive the most votes will serve an initial two-year term, while all others will serve an initial one year term (details below). Ratified Seats: Credit Suisse, Ericsson, Freescale, Fujitsu, Gemalto M2M, Goldman Sachs, Hewlett-Packard, IBM, Intel, Nokia, Red Hat, SAP, SouJava, Software AG, TOTVS and V2COM. Open Election Seats: Eclipse Foundation, Twitter, London Java Community, CloudBees, ARM, Azul Systems, Werner Keil and MoroccoJUG. Newly elected EC Members take their seats on Tuesday, 12 November 2013.  More information is available on the JCP Elections page. Detailed Election Results Voting Period: 15 - 28 October 2013. Number of Eligible Voters: 1088 Percent of Eligible Members Casting Votes: 24.77% Ratified Seats: Candidate Yes Votes (%) No Votes (%) Abstentions Credit Suisse (2year term) 196 (84) 38 (16) 36 Ericsson (2 year term) 196 (88) 27 (12) 47 Freescale (1 year term) 151 (74) 53 (26) 66 Fujitsu (2 year term) 194 (87) 29 (13) 47 Gemalto M2M (1 year term) 170 (80) 42 (20) 58 Goldman Sachs (1 year term) 143 (64) 80 (36) 47 Hewlett-Packard (2 year term) 191 (82) 43 (18) 36 IBM (2 year term) 226 (91) 22 (9) 22 Intel (2 year term) 214 (90) 24 (10) 32 Nokia (1 year term) 139 (64) 78 (36) 53 Red Hat (2 year term) 245 (95) 12 (5) 13 SAP (1 year term) 166 (75) 56 (25) 48 SouJava (2 year term) 226 (92) 19 (8) 25 Software AG (1 year term) 167 (78) 47 (22) 56 TOTVS (1 year term) 129 (69) 59 (31) 82 V2COM (1 year term) 135 (71) 54 (29) 81 Open Election Seats: The top eight candidates have been elected; the top four receive a two year term, and the next four receive a one year term. Candidate Votes (%) Eclipse Foundation (2 year term) 221 (14) Twitter (2 year term) 203 (13) London Java Community (2 year term) 191 (12) CloudBees (2 year term) 179 (11) ARM (1 year term) 176 (11) Azul Systems (1 year term) 166 (10) Werner Keil (1 year term) 128 (8) MoroccoJUG (1 year term) 93 (6) Karan Malhi 56 (3) ChinaNanjingJUG 51 (3) JUG Joglosemar 47 (3) Viresh Wali 45 (3) ITP_JAVA 44 (3) None of the Above 3 (0)

    Read the article

  • "Package dependencies cannot be resolved" error when installing software

    - by Savitha
    Iam getting a problem while install media player packages. Package dependencies cannot be resolved This error could be caused by required additional software packages which are missing or not installable. Furthermore there could be a conflict between software packages which are not allowed to be installed at the same time. Depends: libc6 (>= 2.7) but 2.13-0ubuntu13 is to be installed Depends: libglib2.0-0 (>= 2.24.0) but 2.28.6-0ubuntu1 is to be installed Depends: libgstreamer-plugins-base0.10-0 (>= 0.10.22) but 0.10.32-1ubuntu5 is to be installed Depends: libgstreamer0.10-0 (>= 0.10.26) but 0.10.32-3ubuntu3 is to be installed Depends: liborc-0.4-0 (>= 1:0.4.10) but 1:0.4.11-2 is to be installed Depends: libpostproc-extra-51 (>= 4:0.6-1~) but 4:0.6.4-1ubuntu1+medibuntu1 is to be installed Depends: libswscale-extra-0 (>= 4:0.6-1~) but 4:0.6.4-1ubuntu1+medibuntu1 is to be installed gstreamer0.10-plugins-bad: Depends: libc6 (>= 2.7) but 2.13-0ubuntu13 is to be installed Depends: libcairo2 (>= 1.2.4) but 1.10.2-2ubuntu2 is to be installed Depends: libcdaudio1 (>= 0.99.12p2) but 0.99.12p2-9 is to be installed Depends: libdc1394-22 but it is not going to be installed Depends: libdirectfb-1.2-9 but it is not going to be installed Depends: libflite1 but it is not going to be installed Depends: libgcc1 (>= 1:4.1.1) but 1:4.5.2-8ubuntu4 is to be installed Depends: libglib2.0-0 (>= 2.26.0) but 2.28.6-0ubuntu1 is to be installed Depends: libgsm1 (>= 1.0.13) but it is not going to be installed Depends: libgstreamer-plugins-base0.10-0 (>= 0.10.32) but 0.10.32-1ubuntu5 is to be installed Depends: libgstreamer0.10-0 (>= 0.10.32) but 0.10.32-3ubuntu3 is to be installed Depends: libjasper1 (>= 1.900.1) but 1.900.1-7ubuntu2 is to be installed Depends: libmodplug1 but it is not going to be installed Depends: libmpcdec6 (>= 1:0.1~r435) but it is not going to be installed Depends: libmusicbrainz4c2a (>= 2.1.5) but it is not going to be installed Depends: libofa0 (>= 0.9.3) but it is not going to be installed Depends: liborc-0.4-0 (>= 1:0.4.10) but 1:0.4.11-2 is to be installed Depends: libpng12-0 (>= 1.2.13-4) but 1.2.44-1ubuntu3 is to be installed Depends: librsvg2-2 (>= 2.26.0) but 2.32.1-0ubuntu3 is to be installed Depends: librtmp0 (>= 2.3) but 2.3-2 is to be installed Depends: libschroedinger-1.0-0 (>= 1.0.9) but it is not going to be installed Depends: libsndfile1 (>= 1.0.20) but 1.0.23-1build1 is to be installed Depends: libstdc++6 (>= 4.1.1) but 4.5.2-8ubuntu4 is to be installed Depends: libvpx0 (>= 0.9.0) but it is not going to be installed gstreamer0.10-plugins-ugly: Depends: libc6 (>= 2.7) but 2.13-0ubuntu13 is to be installed Depends: libgcc1 (>= 1:4.1.1) but 1:4.5.2-8ubuntu4 is to be installed Depends: libglib2.0-0 (>= 2.24.0) but 2.28.6-0ubuntu1 is to be installed Depends: libgstreamer-plugins-base0.10-0 (>= 0.10.26) but 0.10.32-1ubuntu5 is to be installed Depends: libgstreamer0.10-0 (>= 0.10.26) but 0.10.32-3ubuntu3 is to be installed Depends: libid3tag0 (>= 0.15.1b) but it is not going to be installed Depends: libmad0 (>= 0.15.1b-3) but it is not going to be installed Depends: liborc-0.4-0 (>= 1:0.4.10) but 1:0.4.11-2 is to be installed Depends: libstdc++6 (>= 4.1.1) but 4.5.2-8ubuntu4 is to be installed

    Read the article

  • Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

    - by Donal
    I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

    Read the article

  • Why is my CPU being used while doing nothing?

    - by Jop
    I have installed Ubuntu GNOME in BIOS mode on my MacBook (BIOS mode so that the proprietary NVIDIA drivers work. I need them for gaming.). For some reason, a lot of CPU is being used while not really doing anything. It swings between 20-30% on both cores, usually. But when I look at the list of processes and sort by CPU usage, I do not see anything special. No processes intensively doing anything. How can I fix this? EDIT: Output of top command. jop@jop-MacBook:~$ top top - 17:08:02 up 41 min, 2 users, load average: 0,51, 0,69, 0,95 Tasks: 202 total, 2 running, 200 sleeping, 0 stopped, 0 zombie %Cpu(s): 11,9 us, 5,8 sy, 0,0 ni, 80,3 id, 0,5 wa, 0,0 hi, 1,5 si, 0,0 st KiB Mem: 7908316 total, 2919940 used, 4988376 free, 153248 buffers KiB Swap: 3906244 total, 0 used, 3906244 free, 1326544 cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3785 root 20 0 195m 82m 26m S 22,9 1,1 2:43.77 Xorg 4429 jop 20 0 1543m 150m 60m S 7,3 1,9 1:26.26 compiz 4198 jop 20 0 633m 21m 11m S 1,7 0,3 0:04.96 unity-panel-ser 7425 jop 20 0 564m 18m 12m S 1,7 0,2 0:00.84 gnome-terminal 7019 jop 20 0 806m 89m 46m S 1,0 1,2 0:10.01 chrome 7323 jop 20 0 966m 93m 23m S 1,0 1,2 0:06.85 chrome 6742 root 20 0 0 0 0 S 0,7 0,0 0:00.43 kworker/0:3 3 root 20 0 0 0 0 S 0,3 0,0 0:06.01 ksoftirqd/0 7008 root 20 0 0 0 0 S 0,3 0,0 0:00.27 kworker/1:3 7302 jop 20 0 972m 96m 28m S 0,3 1,2 0:06.32 chrome 7310 jop 20 0 382m 63m 39m S 0,3 0,8 0:00.34 chrome 7498 jop 20 0 24840 1600 1120 R 0,3 0,0 0:00.22 top 1 root 20 0 27176 2944 1412 S 0,0 0,0 0:01.58 init 2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd 5 root 0 -20 0 0 0 S 0,0 0,0 0:00.00 kworker/0:0H 6 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kworker/u4:0 7 root rt 0 0 0 0 S 0,0 0,0 0:02.04 migration/0 Even when xorg isn't so busy like when I copied, CPU usage is higher then what the processes use.

    Read the article

  • WebLogic Server internal server error [migrated]

    - by Abhinav Pandey
    When I deployed a project in Apache Tomcat 6.0 it is working fine. When I deployed a same project in WebLogic Server 10.3 it's showing an error: Error 500--Internal Server Error javax.servlet.ServletException: [HTTP:101249][weblogic.servlet.internal.WebAppServletContext@ae43b8 - appName: '_appsdir_ab_dir', name: 'ab', context-path: '/ab', spec-version: 'null']: Servlet class FirstServlet for servlet FirstServlet could not be loaded because the requested class was not found in the classpath . java.lang.UnsupportedClassVersionError: FirstServlet : Unsupported major.minor version 51.0.

    Read the article

  • 1000baseT/Full Supported and Advertised but not working!

    - by user11973
    Hello, i'm using a AT3IONT-I motherboard with integrated card. If I ethtool it to 1000 full duplex it wont work! Here is sudo ethtool eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes here is sudo lshw -C network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 03 serial: bc:ae:c5:8b:7d:33 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.021.00-NAPI duplex=full ip=192.168.0.2 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:42 ioport:e800(size=256) memory:f8fff000-f8ffffff memory:f8ff8000-f8ffbfff memory:fbff0000-fbffffff And lspci -nn: 00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1) 00:00.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a88] (rev b1) 00:03.0 ISA bridge [0601]: nVidia Corporation MCP79 LPC Bridge [10de:0aad] (rev b3) 00:03.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0aa4] (rev b1) 00:03.2 SMBus [0c05]: nVidia Corporation MCP79 SMBus [10de:0aa2] (rev b1) 00:03.3 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a89] (rev b1) 00:03.5 Co-processor [0b40]: nVidia Corporation MCP79 Co-processor [10de:0aa3] (rev b1) 00:04.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa5] (rev b1) 00:04.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa6] (rev b1) 00:06.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa7] (rev b1) 00:06.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa9] (rev b1) 00:08.0 Audio device [0403]: nVidia Corporation MCP79 High Definition Audio [10de:0ac0] (rev b1) 00:09.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Bridge [10de:0aab] (rev b1) 00:0b.0 RAID bus controller [0104]: nVidia Corporation MCP79 RAID Controller [10de:0abc] (rev b1) 00:0c.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac4] (rev b1) 00:10.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0aa0] (rev b1) 00:15.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac6] (rev b1) 03:00.0 VGA compatible controller [0300]: nVidia Corporation ION VGA [10de:087d] (rev b1) 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) If i use Code: sudo ethtool -s eth0 speed 1000 duplex full autoneg off then in ethtool speed is Unknown and it doesn't work; if I set it via pre-up it wont work either... Please help!! Thanks!

    Read the article

  • algorithm for project euler problem no 18

    - by Valentino Ru
    Problem number 18 from Project Euler's site is as follows: By starting at the top of the triangle below and moving to adjacent numbers on the row below, the maximum total from top to bottom is 23. 3 7 4 2 4 6 8 5 9 3 That is, 3 + 7 + 4 + 9 = 23. Find the maximum total from top to bottom of the triangle below: 75 95 64 17 47 82 18 35 87 10 20 04 82 47 65 19 01 23 75 03 34 88 02 77 73 07 63 67 99 65 04 28 06 16 70 92 41 41 26 56 83 40 80 70 33 41 48 72 33 47 32 37 16 94 29 53 71 44 65 25 43 91 52 97 51 14 70 11 33 28 77 73 17 78 39 68 17 57 91 71 52 38 17 14 91 43 58 50 27 29 48 63 66 04 68 89 53 67 30 73 16 69 87 40 31 04 62 98 27 23 09 70 98 73 93 38 53 60 04 23 NOTE: As there are only 16384 routes, it is possible to solve this problem by trying every route. However, Problem 67, is the same challenge with a triangle containing one-hundred rows; it cannot be solved by brute force, and requires a clever method! ;o) The formulation of this problems does not make clear if the "Traversor" is greedy, meaning that he always choosed the child with be higher value the maximum of every single walkthrough is asked The NOTE says, that it is possible to solve this problem by trying every route. This means to me, that is is also possible without! This leads to my actual question: Assumed that not the greedy one is the max, is there any algorithm that finds the max walkthrough value without trying every route and that doesn't act like the greedy algorithm? I implemented an algorithm in Java, putting the values first in a node structure, then applying the greedy algorithm. The result, however, is cosidered as wrong by Project Euler. sum = 0; void findWay(Node node){ sum += node.value; if(node.nodeLeft != null && node.nodeRight != null){ if(node.nodeLeft.value > node.nodeRight.value){ findWay(node.nodeLeft); }else{ findWay(node.nodeRight); } } }

    Read the article

  • Moms on Mobile: Are They Way Ahead of You?

    - by Mike Stiles
    You may have no idea how much and how fast moms are embracing mobile. Of all the demographics that can be targeted by marketers, moms have always been at or near the top of the list. And why not? They’re running households, they’re all over town, they’re making buying decisions, and they’re influencing family and friends. They, out of necessity, become masters of efficiency and time management. So when a technology tool, like mobile, comes along that assists with that efficiency and time management, we would obviously expect them to take advantage of it. So if it’s obvious, why are so many big, sophisticated brands left choking on the dust of moms who have zoomed past them in the adoption of mobile, and social on mobile? Let’s break down some hard truths as presented by a Mojiava report: -Moms spend 6.1 hours per day on average on their smartphones – more than magazines, TV or radio. -46% took action after seeing a mobile ad. -51% self-identify as “addicted” to their smartphone. -Households with an income of $25K-$50K have about the same mobile penetration among moms as those with incomes of $50K-$75K. So mobile is regarded as a necessity for middle-class moms. -Even moms without smartphones spend 2.5 hours on average per day on some connected mobile device. -Of moms with such devices, 9.8% have an iPad, 9.5% a Kindle and 5.7% an iPod Touch. -Of tablet-owning moms, 97% bought something using their tablet in the last month. -31% spend over 10 hours per week on their tablet, but less than 2 hours per week on their PCs. -62% of connected moms use shopping apps. -46% want to get info on their mobile while in a store. -Half of connected moms use social on their mobile. And they’re engaged. 81% are brand fans, 86% post updates, and 84% comment. If women and moms are one of your primary targets and you find yourself with no strong social channels where content is driving engagement and relationship-building, with sites not optimized for mobile, or with no tablet or smartphone apps, you have been solidly left behind by your customers and prospects. And their adoption of mobile and social on mobile is only exponentially speeding up, not slowing down. How much sense does it make when your customer is ready to act on your mobile ad, wants to user your iPad app to buy something from you, wants to be your fan on Facebook, wants to get messages and deals from you while they’re in your store…but you’re completely absent? I’ll help you cheat on the test by giving you the answer…no sense at all. Catch up to momma.

    Read the article

  • Silverlight and WCF caching

    - by subodhnpushpak
    There are scenarios where Silverlight client calls WCF (or REST) service for data. Now, if the data is cached on the WCF layer, the calls can take considerable resources at the server if NOT cached. Keeping that in mind along with the fact that cache is an cross-cutting aspect, and therefore it should be as easy as possible to put Cache wherever required. The good thing about the solution is that it caches based on the inputs. The input can be basic type of any complex type. If input changes the data is fetched and then cached for further used. If same input is provided again, data id fetched from the cache. The cache logic itself is implemented as PostSharp aspect, and it is as easy as putting an attribute over service call to switch on cache. Notice how clean the code is:        [OperationContract]       [CacheOnArgs(typeof(int))] // based on actual value of cache        public string DoWork(int value)        {            return string.Format("You entered: {0} @ cached time {1}", value, System.DateTime.Now);        } The cache is implemented as POST Sharp as below 1: public override void OnInvocation(MethodInvocationEventArgs eventArgs) 2: { 3: try 4: { 5: object value = new object(); 6: object[] args = eventArgs.GetArgumentArray(); 7: if (args != null || args.Count() > 0) 8: { 9:   10: string key = string.Format("{0}_{1}", eventArgs.Method.Name, XMLUtility<object>.GetDataContractXml(args[0], null));// Compute the cache key (details omitted). 11:   12: 13: value = GetFromCache(key); 14: if (value == null) 15: { 16: eventArgs.Proceed(); 17: value = XMLUtility<object>.GetDataContractXml(eventArgs.ReturnValue, null); 18: value = eventArgs.ReturnValue; 19: AddToCache(key, value); 20: return; 21: } 22:   23:   24: Log(string.Format("Data returned from Cache {0}",value)); 25: eventArgs.ReturnValue = value; 26: } 27: } 28: catch (Exception ex) 29: { 30: //ApplicationLogger.LogException(ex.Message, Source.UtilityService); 31: } 32: } 33:   34: private object GetFromCache(string inputKey) { if (ServerConfig.CachingEnabled) { return WCFCache.Current[inputKey]; } return null; }private void AddToCache(string inputKey,object outputValue) 35: { 36: if (ServerConfig.CachingEnabled) 37: { 38: if (WCFCache.Current.CachedItemsNumber < ServerConfig.NumberOfCachedItems) 39: { 40: if (ServerConfig.SlidingExpirationTime <= 0 || ServerConfig.SlidingExpirationTime == int.MaxValue) 41: { 42: WCFCache.Current[inputKey] = outputValue; 43: } 44: else 45: { 46: WCFCache.Current.Insert(inputKey, outputValue, new TimeSpan(0, 0, ServerConfig.SlidingExpirationTime), true); 47:   48: // _bw.DoWork += bw_DoWork; 49: //string arg = string.Format("{0}|{1}", inputKey,outputValue); 50: //_bw.RunWorkerAsync(inputKey ); 51: } 52: } 53: } 54: }     The cache class can be extended to support Velocity / memcahe / Nache. the attribute can be used over REST services as well. Hope the above helps. Here is the code base for the same.   Please do provide your inputs / comments.

    Read the article

  • Product Development Investment: A Measure of Vendor Performance

    - by Jim Mcglothlin
    The relationship between a large, complex organization and its key suppliers of information technology is normally more than just "strategic". Expectations about the duration of the relationship typically exceed 20 years. Enterprise applications and technology infrastructure are not expected to be changed out like petunias. So how would you rate the due diligence processes as performed in Higher Education when selecting critical, transformational information technology? My observation: I see a lot of effort put into elaborate demonstration of basic software functionality. I see a lot of attention paid to the cost element of technology acquisition, including the contracted cost of implementation consulting services. But the factor that receives only cursory analysis and due diligence is long-term performance--the ability of a vendor to grow, expand, and develop, and bring its customers along with it. So what should you look for in a long-term IT supplier? Oracle has a public track record for product development. The annual investment has been on a run rate of almost $3 Billion organic product development. Oracle's well-publicized acquisitions and mergers have been supplemental to its R&D. This is important for Higher Education. Another meaningful way to evaluate a company is to look at the tangible track record of enhancement. Consider the Oracle-PeopleSoft enterprise business platform since acquired by Oracle 6 years ago: Product or Technology Enhancement Customer or User Impact Service Oriented Architecture (SOA) 300+ new web services delivered in versions 9.0 & 9.1 provide flexibility, so that customers can integrate PeopleSoft with other applications. Campus Solutions has added Admissions and Constituent Web Services. Constituent Relationship Management PeopleSoft CRM 9.1 for Higher Education introduced new process flows for student recruiting and retention to support "Student Success" initiatives. A 360 view of the constituent is now delivered, and the concept of a single-stop Student Services Center is now in CRM 9.1 with tight integration to PeopleSoft Campus Solutions. Human Capital Management Contract Pay for Education, with flexibility for configuration and calculation, has been extended in HCM 9.1. New chartfield integration among Project Costing - Time & Labor - Payroll to serve the labor distribution requirements for Grants / Sponsored Research. Talent Management PeopleSoft 9.0 and 9.1 feature an integrated talent management approach centered on definitions in "Profile Manager", with all new usability improvements. Internal and external candidate pools, and the entire recruitment process, are driven by delivered configurable selection and on-boarding processes. Interview scheduling, and online job offers are newly delivered processes. Performance Management PeopleSoft HCM ePerformance 9.1 will include significant new functionality designed to help organizations more effectively align business objectives with employee goals. Using an Organization Chart view, your business goals can flow down to become tangible objectives per employee. Succession Planning / Workforce Development New in HCM 9.0, enhanced in 9.1, is a planning capability for regular or unusual (major organizational change) succession of internal or external candidates. PeopleSoft supports employee-based career planning, which ultimately increases the integrity of the succession planning process (identify their career needs, plans, preferences, and interests). Dashboards / Oracle Business Intelligence Application Suite Oracle Human Resources Analytics provides the workforce information foundation that integrates data from HR functional areas and Finance. Oracle Human Resources Analytics delivers 9 dashboards and over 200 reports. Provide your HR professionals and front-line managers the tools to analyze workforce staffing, retention, productivity, to better source high-quality applicants, and to reduce absence costs. Multi-year Planning and Commitment Control External funding sources, especially Grants, require a multi-year encumbrance business process. PeopleSoft HCM 9.1 adds multi-year funding and commitment control, including budget checking. The newly designed Real Time Budget Checking will provide the customer with an updated snapshot of their budget and encumbrances at any given time. Position Budgeting with Hyperion Hyperion Planning world-class products now include delivered integration to PeopleSoft HCM. Position Budgeting is available in the new Public Sector Planning module of Hyperion. Web 2.0 features for the latest in usability PeopleSoft 9.1 features a contemporary internet user experience: Partial-page refreshing Drag and drop pagelets New menu structure Navigation pagelets Modal popup message windows Favorites & recently used links Type-ahead Drag and drop grid columns, pop-out grids Portal Workspaces Enterprise 2.0 for your collaborative web communities, using new content management, along with Wikis, blogs, and discussion forums in PeopleSoft Portal 9.1. PeopleTools enhanced by Oracle Fusion Middleware Standards-based tools have been added to the PeopleTools application infrastructure: BI (XML) Publisher, Java tools. Certified for use with PeopleSoft: Oracle Business Intelligence (OBIEE), Oracle Enterprise Manager, Oracle Weblogic Server, Oracle SOA Suite. Hosting for PeopleSoft applications A solid new deployment option: Oracle On Demand remote hosting center for high scalability, security, and continuity of operations. Business Process Outsourcing (BPO) for HCM / Payroll functions Partnership with AT&T provides hosting of HR/Payroll application along with payroll business process operations, and subscription-based service fees (SaaS). AT&T BPO full service includes pay sheet processing, bank and 3rd party file transfer, payroll tax handling, etc. Continuous Delivery Model Feature Packs provide faster time-to-benefit; new features become available in PeopleSoft 9.1 (or Campus Solutions 9.0) without need to perform upgrade. Golden person data model across all campus applications Oracle Higher Education Constituent Hub provides synchronization and data governance of person data across any application, e.g. HR/ Payroll, Student Information System, Housing, Emergency Contact, LMS, CRM. Oracle's aggressive enhancement plans within the "Applications Unlimited" program continue, as new functionality is under development for a new version of a PeopleSoft release planned for 2012. Meanwhile, new capabilities are planned on an annual basis in Feature Packs. PeopleSoft just delivered the HCM 2010 Feature Pack and another is planned for 2011. In February we plan to have over 100 customers from our Customer Advisory Boards at our PeopleSoft Development Center in California to review designs for all of these releases. For those of you near New York City The investment and progressive development story described above is the subject of an Oracle road show event on February 9, 2011. Charting Your Course with Oracle Applications is a global event series designed to help business and IT executives assess the impact of new inflection points on their business and applications roadmap: changing workforces, shifting customer and constituent bases, and increased volatility. Learn how innovations ranging from new deployment models like cloud computing to the introduction of social applications and smart devices are delivering results across all areas of business and industry. THIS DOCUMENT IS FOR INFORMATIONAL PURPOSES ONLY AND MAY NOT BE INCORPORATED INTO A CONTRACT OR AGREEMENT.

    Read the article

  • DD-WRT: DNSMasq expand-hosts not working

    - by Craig Walker
    I have a Linksys router running DD-WRT (Firmware: DD-WRT v24-sp2 (09/08/09) mini). I have it successfully resolving the DNS names for my DHCP-assigned systems, but only when I fully-qualify those domains. This is despite using the "expand-hosts" DNSMasq additional option, which is supposed to activate this precise function. Here's my dnsmasq.conf: interface=br0 resolv-file=/tmp/resolv.dnsmasq domain=example.com dhcp-leasefile=/tmp/dnsmasq.leases dhcp-lease-max=51 dhcp-option=lan,3,10.77.0.5 dhcp-authoritative dhcp-range=lan,10.77.0.100,10.77.0.149,255.255.0.0,1440m dhcp-host=00:1A:A0:1D:82:5A,astatichostname,10.77.1.40,infinite expand-hosts (FYI: example.com and astatichostname are placeholders for the real-deal names I use. My network uses 10.77.0.0/16; my router is on 10.77.0.5.) Results: > nslookup astatichostname 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 ** server can't find astatichostname: NXDOMAIN > nslookup astatichostname.example.com 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 Name: astatichostname.example.com Address: 10.77.1.40 Is there something else that could be tripping up expand-host in DNSMasq?

    Read the article

  • VMware Tools in Ubuntu guest on VMware Server 2 do not build

    - by ulf
    When trying to build the VMware tools in my Ubuntu 9.10 64 bit guest on a VMware Server 2.0.2 host with Debian 5 I'm getting strange errors like: Building the vmmemctl module. Using 2.6.x kernel build system. make: Gehe in Verzeichnis '/tmp/vmware-config8/vmmemctl-only' make -C /lib/modules/2.6.31-19-server/build/include/.. SUBDIRS=$PWD SRCROOT=$PWD/. modules make[1]: Betrete Verzeichnis '/usr/src/linux-headers-2.6.31-19-server' CC [M] /tmp/vmware-config8/vmmemctl-only/backdoorGcc64.o In file included from /tmp/vmware-config8/vmmemctl-only/backdoor.h:29, from /tmp/vmware-config8/vmmemctl-only/backdoorGcc64.c:38: /tmp/vmware-config8/vmmemctl-only/vm_basic_types.h:108:7: warning: "__FreeBSD__" is not defined CC [M] /tmp/vmware-config8/vmmemctl-only/os.o In file included from /tmp/vmware-config8/vmmemctl-only/os.c:51: /tmp/vmware-config8/vmmemctl-only/compat_wait.h:78: error: conflicting types for ‘poll_initwait’ include/linux/poll.h:70: note: previous declaration of ‘poll_initwait’ was here make[2]: *** [/tmp/vmware-config8/vmmemctl-only/os.o] Fehler 1 make[1]: *** [_module_/tmp/vmware-config8/vmmemctl-only] Fehler 2 make[1]: Verlasse Verzeichnis '/usr/src/linux-headers-2.6.31-19-server' make: *** [vmmemctl.ko] Fehler 2 make: Verlasse Verzeichnis '/tmp/vmware-config8/vmmemctl-only' Unable to build the vmmemctl module. I googled half the Internet but couldn't come to a solution. None of the kernel modules seems to build correctly. While googling I read something about a bug in this kernel tree.

    Read the article

  • local msmtp and ovh hosting

    - by klez
    I have my personal email hosted on OVH (personal hosting plan) and I'm not able to send mails using msmtp. Here's a typical session ignoring system configuration file /etc/msmtprc: File o directory non esistente loaded user configuration file /home/klez/.msmtprc using account default from /home/klez/.msmtprc host = ssl0.ovh.net port = 465 timeout = off protocol = smtp domain = localhost auth = choose user = federicoculloca%xxxxxxx password = * ntlmdomain = (not set) tls = on tls_starttls = off tls_trust_file = (not set) tls_crl_file = (not set) tls_fingerprint = (not set) tls_key_file = (not set) tls_cert_file = (not set) tls_certcheck = off tls_force_sslv3 = off tls_min_dh_prime_bits = (not set) tls_priorities = (not set) auto_from = off maildomain = (not set) from = federicoculloca@xxxxxxxx dsn_notify = (not set) dsn_return = (not set) keepbcc = off logfile = (not set) syslog = (not set) reading recipients from the command line TLS certificate information: Owner: Common Name: ssl0.ovh.net Organizational unit: Domain Control Validated Issuer: Common Name: OVH Secure Certification Authority Organization: OVH SAS Organizational unit: Low Assurance Country: FR Validity: Activation time: lun 31 gen 2011 01:00:00 CET Expiration time: mer 15 feb 2012 00:59:59 CET Fingerprints: SHA1: F9:DC:41:F9:A2:38:51:9B:56:E4:98:E6:CD:81:31:42:E6:0E:26:6D MD5: FC:EC:F3:8F:28:E4:7E:28:99:89:E6:BB:C9:DF:71:CE <-- 220 ns0.ovh.net ssl0.ovh.net. You connect to mail427.ha.ovh.net ESMTP --> EHLO localhost <-- 250-ssl0.ovh.net. You connect to mail427.ha.ovh.net <-- 250-AUTH LOGIN PLAIN <-- 250-AUTH=LOGIN PLAIN <-- 250-PIPELINING <-- 250-8BITMIME <-- 250 SIZE 109000000 --> AUTH PLAIN xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx <-- 235 ok, go ahead (#2.0.0) --> MAIL FROM:<federicoculloca@xxxxx> --> RCPT TO:<[email protected]> --> DATA <-- 250 ok <-- 250 ok <-- 354 go ahead --> hello world --> . <-- 554 mail server permanently rejected message (#5.3.0) And my configuration # ~/.msmtp # Mostly from Peter Garrett's examples # https://lists.ubuntu.com/archives/ubuntu-users/2007-September/122698.html # Accounts from Scott Robbins' `A Quick Guide to Mutt' # http://home.nyc.rr.com/computertaijutsu/mutt.html account xxxxx host ssl0.ovh.net from federicoculloca@xxxxxx auth on user federicoculloca%xxxxxx password xxxxxx tls on tls_certcheck off tls_starttls off Any idea?

    Read the article

  • SATA drives or chipset throwing DRDY ERR and ICRC ABRT

    - by Matt
    I have an SD-VIA-1A2S PCI card with 2 sata ports (and one ATA-133 that isn't used). Two new Western Digital Caviar Green drives (WD10EARS 1TB) throw repeated errors in kern.log (removed date/time/host info for brevity): [ 7.376475] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1000500 action 0x6 [ 7.376480] ata2.00: BMDMA stat 0x5 [ 7.376483] ata2: SError: { UnrecovData Proto TrStaTrns } [ 7.376489] ata2.00: cmd c8/00:40:20:00:00/00:00:00:00:00/e0 tag 0 dma 32768 in [ 7.376490] res 51/84:2f:20:00:00/00:00:00:00:00/e0 Emask 0x12 (ATA bus error) [ 7.376493] ata2.00: status: { DRDY ERR } [ 7.376495] ata2.00: error: { ICRC ABRT } [ 7.376504] ata2: hard resetting link I'm using Ubuntu 9.04 - 2.6.28-18-generic, though I have tried live cds of Ubuntu 9.10, Fedora 12 and OpenSUSE 11.2 - all running various 2.6.31 kernels - and all received the same error. Based on testing these drives and this card in two other machines and combos of connecting the drives directly to the motherboard or the add-in card, I'm relatively convinced that it's the VIA chipset that is the problem. Another computer that also has an onboard VIA SATA chipset (like the add-in card) produces the same errors when the drives are directly on that motherboard. I have been able to verify that the drives are perfectly good, and I tried everything I can think of in terms of swapping cables, psu isn't overloaded, etc. The error happens on boot once or twice, after using fdisk on the drive once or twice, and constantly when attempting to sync a new mdadm raid 1 array created on the two drives. Any thoughts on where to go from here - driver/kernel wise? I'm completely open to buying a new PCI add-in card if someone can recommend one with 2 internal sata ports that works well in Debian/Ubuntu. Thanks!

    Read the article

  • Heartbeat won't successfully start up resources from a cold boot when a failed node is present

    - by Matthew
    I currently have two ubuntu servers running Heartbeat and DRBD. The servers are directory connected with a 1000Mbps crossover cable on eth1 and have access to an IP camera LAN on eth0. Now, let's say that one node is down and the remaining functional node is booting after having been shut down. The node that is still functioning won't start up heartbeat and provide access to the drbd resource from a cold boot. I have to manually restart heartbeat by sudo service heartbeat restart to get everything up and running. How can I get it to start fine from a cold start, when only one server is present? Here is the ha.cf: debug /var/log/ha-debug logfile /var/log/ha-log logfacility none keepalive 2 deadtime 10 warntime 7 initdead 60 ucast eth1 192.168.2.2 ucast eth0 10.1.10.201 node EMserver1 node EMserver2 respawn hacluster /usr/lib/heartbeat/ipfail ping 10.1.10.22 10.1.10.21 10.1.10.11 auto_failback off Some material from the syslog: harc[4604]: 2012/11/27_13:54:49 info: Running /etc/ha.d//rc.d/status status mach_down[4632]: 2012/11/27_13:54:49 info: /usr/share/heartbeat/mach_down: nice_failback: foreign resources acquired mach_down[4632]: 2012/11/27_13:54:49 info: mach_down takeover complete for node emserver2. Nov 27 13:54:49 EMserver1 heartbeat: [4586]: info: Initial resource acquisition complete (T_RESOURCES(us)) Nov 27 13:54:49 EMserver1 heartbeat: [4586]: info: mach_down takeover complete. IPaddr[4679]: 2012/11/27_13:54:49 INFO: Resource is stopped Nov 27 13:54:49 EMserver1 heartbeat: [4605]: info: Local Resource acquisition completed. harc[4713]: 2012/11/27_13:54:49 info: Running /etc/ha.d//rc.d/ip-request-resp ip-request-resp ip-request-resp[4713]: 2012/11/27_13:54:49 received ip-request-resp IPaddr::10.1.10.254 OK yes ResourceManager[4732]: 2012/11/27_13:54:50 info: Acquiring resource group: emserver1 IPaddr::10.1.10.254 drbddisk::r0 Filesystem::/dev/drbd1::/shr::ext4 nfs-kernel-server IPaddr[4759]: 2012/11/27_13:54:50 INFO: Resource is stopped ResourceManager[4732]: 2012/11/27_13:54:50 info: Running /etc/ha.d/resource.d/IPaddr 10.1.10.254 start IPaddr[4816]: 2012/11/27_13:54:50 INFO: Using calculated nic for 10.1.10.254: eth0 IPaddr[4816]: 2012/11/27_13:54:50 INFO: Using calculated netmask for 10.1.10.254: 255.255.255.0 IPaddr[4816]: 2012/11/27_13:54:50 INFO: eval ifconfig eth0:0 10.1.10.254 netmask 255.255.255.0 broadcast 10.1.10.255 IPaddr[4804]: 2012/11/27_13:54:50 INFO: Success ResourceManager[4732]: 2012/11/27_13:54:50 info: Running /etc/ha.d/resource.d/drbddisk r0 start Filesystem[4965]: 2012/11/27_13:54:50 INFO: Resource is stopped ResourceManager[4732]: 2012/11/27_13:54:50 info: Running /etc/ha.d/resource.d/Filesystem /dev/drbd1 /shr ext4 start Filesystem[5039]: 2012/11/27_13:54:50 INFO: Running start for /dev/drbd1 on /shr Filesystem[5033]: 2012/11/27_13:54:51 INFO: Success ResourceManager[4732]: 2012/11/27_13:54:51 info: Running /etc/init.d/nfs-kernel-server start Nov 27 13:55:00 EMserver1 heartbeat: [4586]: info: Local Resource acquisition completed. (none) Nov 27 13:55:00 EMserver1 heartbeat: [4586]: info: local resource transition completed. Nov 27 13:57:46 EMserver1 heartbeat: [4586]: info: Heartbeat shutdown in progress. (4586) Nov 27 13:57:46 EMserver1 heartbeat: [5286]: info: Giving up all HA resources. ResourceManager[5301]: 2012/11/27_13:57:46 info: Releasing resource group: emserver1 IPaddr::10.1.10.254 drbddisk::r0 Filesystem::/dev/drbd1::/shr::ext4 nfs-kernel-server ResourceManager[5301]: 2012/11/27_13:57:46 info: Running /etc/init.d/nfs-kernel-server stop ResourceManager[5301]: 2012/11/27_13:57:46 info: Running /etc/ha.d/resource.d/Filesystem /dev/drbd1 /shr ext4 stop Filesystem[5372]: 2012/11/27_13:57:46 INFO: Running stop for /dev/drbd1 on /shr Filesystem[5372]: 2012/11/27_13:57:47 INFO: Trying to unmount /shr Filesystem[5372]: 2012/11/27_13:57:47 INFO: unmounted /shr successfully Filesystem[5366]: 2012/11/27_13:57:47 INFO: Success ResourceManager[5301]: 2012/11/27_13:57:47 info: Running /etc/ha.d/resource.d/drbddisk r0 stop ResourceManager[5301]: 2012/11/27_13:57:47 info: Running /etc/ha.d/resource.d/IPaddr 10.1.10.254 stop IPaddr[5509]: 2012/11/27_13:57:47 INFO: ifconfig eth0:0 down IPaddr[5497]: 2012/11/27_13:57:47 INFO: Success Nov 27 13:57:47 EMserver1 heartbeat: [5286]: info: All HA resources relinquished. Nov 27 13:57:48 EMserver1 heartbeat: [4586]: info: killing /usr/lib/heartbeat/ipfail process group 4603 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBFIFO process 4589 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBWRITE process 4590 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBREAD process 4591 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBWRITE process 4592 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBREAD process 4593 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBWRITE process 4594 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBREAD process 4595 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBWRITE process 4596 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBREAD process 4597 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBWRITE process 4598 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: killing HBREAD process 4599 with signal 15 Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4589 exited. 11 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4596 exited. 10 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4598 exited. 9 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4590 exited. 8 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4595 exited. 7 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4591 exited. 6 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4592 exited. 5 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4593 exited. 4 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4597 exited. 3 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4594 exited. 2 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: Core process 4599 exited. 1 remaining Nov 27 13:57:49 EMserver1 heartbeat: [4586]: info: emserver1 Heartbeat shutdown complete. Here is some more from the log ResourceManager[2576]: 2012/11/28_16:32:42 info: Acquiring resource group: emserver1 IPaddr::10.1.10.254 drbddisk::r0 Filesystem::/dev/drbd1::/shr::ext4 nfs-kernel-server IPaddr[2602]: 2012/11/28_16:32:42 INFO: Running OK Filesystem[2653]: 2012/11/28_16:32:43 INFO: Running OK Nov 28 16:32:52 EMserver1 heartbeat: [1695]: WARN: node emserver2: is dead Nov 28 16:32:52 EMserver1 heartbeat: [1695]: info: Dead node emserver2 gave up resources. Nov 28 16:32:52 EMserver1 ipfail: [1807]: info: Status update: Node emserver2 now has status dead Nov 28 16:32:52 EMserver1 heartbeat: [1695]: info: Link emserver2:eth1 dead. Nov 28 16:32:53 EMserver1 ipfail: [1807]: info: NS: We are still alive! Nov 28 16:32:53 EMserver1 ipfail: [1807]: info: Link Status update: Link emserver2/eth1 now has status dead Nov 28 16:32:55 EMserver1 ipfail: [1807]: info: Asking other side for ping node count. Nov 28 16:32:55 EMserver1 ipfail: [1807]: info: Checking remote count of ping nodes. Nov 28 16:32:57 EMserver1 heartbeat: [1695]: info: Heartbeat shutdown in progress. (1695) Nov 28 16:32:57 EMserver1 heartbeat: [2734]: info: Giving up all HA resources. ResourceManager[2751]: 2012/11/28_16:32:57 info: Releasing resource group: emserver1 IPaddr::10.1.10.254 drbddisk::r0 Filesystem::/dev/drbd1::/shr::ext4 nfs-kernel-server ResourceManager[2751]: 2012/11/28_16:32:57 info: Running /etc/init.d/nfs-kernel-server stop ResourceManager[2751]: 2012/11/28_16:32:57 info: Running /etc/ha.d/resource.d/Filesystem /dev/drbd1 /shr ext4 stop Filesystem[2829]: 2012/11/28_16:32:57 INFO: Running stop for /dev/drbd1 on /shr Filesystem[2829]: 2012/11/28_16:32:57 INFO: Trying to unmount /shr Filesystem[2829]: 2012/11/28_16:32:58 INFO: unmounted /shr successfully Filesystem[2823]: 2012/11/28_16:32:58 INFO: Success ResourceManager[2751]: 2012/11/28_16:32:58 info: Running /etc/ha.d/resource.d/drbddisk r0 stop ResourceManager[2751]: 2012/11/28_16:32:58 info: Running /etc/ha.d/resource.d/IPaddr 10.1.10.254 stop IPaddr[2971]: 2012/11/28_16:32:58 INFO: ifconfig eth0:0 down IPaddr[2958]: 2012/11/28_16:32:58 INFO: Success Nov 28 16:32:58 EMserver1 heartbeat: [2734]: info: All HA resources relinquished. Nov 28 16:32:59 EMserver1 heartbeat: [1695]: info: killing /usr/lib/heartbeat/ipfail process group 1807 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBFIFO process 1777 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBWRITE process 1778 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBREAD process 1779 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBWRITE process 1780 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBREAD process 1781 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBWRITE process 1782 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBREAD process 1783 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBWRITE process 1784 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBREAD process 1785 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBWRITE process 1786 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: killing HBREAD process 1787 with signal 15 Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1778 exited. 11 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1779 exited. 10 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1780 exited. 9 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1781 exited. 8 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1782 exited. 7 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1783 exited. 6 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1784 exited. 5 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1785 exited. 4 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1786 exited. 3 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1787 exited. 2 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: Core process 1777 exited. 1 remaining Nov 28 16:33:01 EMserver1 heartbeat: [1695]: info: emserver1 Heartbeat shutdown complete. If I restarted heartbeat at this point... the resources heartbeat controls would start up fine.... please help!

    Read the article

  • red5 Install on Ubuntu 10.04? Problems with libslf4j

    - by mrgordon
    I've been trying for many days to get Red5 to install on Ubuntu 10.04. I finally managed to get red5.sh to stop hanging a few seconds in but now I'm getting the following error: Setting default logging context: default Exception in thread "main" java.lang.reflect.InvocationTargetException at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.red5.server.Bootstrap.bootStrap(Bootstrap.java:135) at org.red5.server.Bootstrap.main(Bootstrap.java:50) Caused by: java.lang.NoSuchMethodError: org.slf4j.impl.StaticLoggerBinder.getContextSelector()Lch/qos/logback/classic/selector/ContextSelector; at org.red5.logging.Red5LoggerFactory.getLogger(Red5LoggerFactory.java:121) at org.red5.logging.Red5LoggerFactory.getLogger(Red5LoggerFactory.java:108) at org.red5.server.Launcher.launch(Launcher.java:51) ... 6 more I suspected that this had to do with slf4j not being installed or on my classpath. I installed logback and libslf4j-java from aptitude and I see related files in my red5 lib directories. For example: /usr/share/red5/lib/slf4j-api-1.6.1.jar /usr/share/red5/lib/log4j-over-slf4j-1.6.1.jar /usr/share/red5/lib/logback-classic-0.9.26.jar /usr/share/red5/lib/logback-core-0.9.26.jar /usr/share/red5/lib/jcl-over-slf4j-1.6.1.jar /usr/share/red5/lib/jul-to-slf4j-1.6.1.jar And I set my classpath to /usr/share/red5/lib/ Any ideas on where to proceed from here? There seem to be a lot of people having trouble getting 10.04 and red5 0.9 working together. I've tried red5-0.9.1.tar.gz and red5_0.9.0-RC1_all.deb. The libraries above should be all that are needed according to Red5's documentation and I got the latest version of each.

    Read the article

  • Enable PasswordAuthentication on OpenSuse 10

    - by Riduidel
    Hi, I've a virtual instance of Suse 10 running in my VMWare player, and I'm fighting against it to allow ssh password authentcation. How can I make it working since I already have tuned the /etc/ssh/ssh_config file like that # $OpenBSD: ssh_config,v 1.20 2005/01/28 09:45:53 dtucker Exp $ Host * # ForwardAgent no ForwardX11 yes ForwardX11Trusted yes PubkeyAuthentication no RhostsRSAAuthentication no RSAAuthentication no PasswordAuthentication yes HostbasedAuthentication no Protocol 2 SendEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES SendEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT SendEnv LC_IDENTIFICATION LC_ALL With ssh connection sending me the following logs Incoming packet #0x5, type 51 / 0x33 (SSH2_MSG_USERAUTH_FAILURE) 00000000 00 00 00 1e 70 75 62 6c 69 63 6b 65 79 2c 6b 65 ....publickey,ke 00000010 79 62 6f 61 72 64 2d 69 6e 74 65 72 61 63 74 69 yboard-interacti 00000020 76 65 00 ve. Outgoing packet #0x6, type 50 / 0x32 (SSH2_MSG_USERAUTH_REQUEST) 00000000 00 00 00 04 72 6f 6f 74 00 00 00 0e 73 73 68 2d ....root....ssh- 00000010 63 6f 6e 6e 65 63 74 69 6f 6e 00 00 00 14 6b 65 connection....ke 00000020 79 62 6f 61 72 64 2d 69 6e 74 65 72 61 63 74 69 yboard-interacti 00000030 76 65 00 00 00 00 00 00 00 00 ve........ Telling me that it expects publickey and keyboard-interactive authentications, which I don't want to use.

    Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >