Search Results

Search found 7124 results on 285 pages for 'printer driver'.

Page 270/285 | < Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Tomcat can't talk to MySql after outage

  - by gav

  I missed a payment for my server and hey suspended my account for a day or so. When they brought the server back up all my data was in tact but for some reason Tomcat can't make a JDBC connection to my MySql server. They both run on the same machine and hence I have a bind address of 127.0.0.1. It's strange because I have reset the machine of my own accord before without issue but clearly something has been reset in the downtime. I followed this guide (Just the bits which don't concern S3, I am not on Amazon infrastructure) originally and everything worked as expected. I'm very new to being a SysAdmin and I'm not sure what to try, how would you go about diagnosing this issue? The stack trace I get is as follows; INFO: Deploying web application archive myapp-1.1.war 2010-05-26 22:07:22,221 [main] ERROR context.ContextLoader - Context initialization failed org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'messageSource': Initialization of bean failed; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'transactionManager': Cannot resolve reference to bean 'sessionFactory' while setting bean property 'sessionFactory'; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'sessionFactory': Cannot resolve reference to bean 'hibernateProperties' while setting bean property 'hibernateProperties'; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'hibernateProperties': Cannot resolve reference to bean 'dialectDetector' while setting bean property 'properties' with key [hibernate.dialect]; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'dialectDetector': Invocation of init method failed; nested exception is org.springframework.jdbc.support.MetaDataAccessException: Could not get Connection for extracting meta data; nested exception is org.springframework.jdbc.CannotGetJdbcConnectionException: Could not get JDBC Connection; nested exception is org.apache.commons.dbcp.SQLNestedException: Cannot create PoolableConnectionFactory (Communications link failure The last packet sent successfully to the server was 0 milliseconds ago. The driver has not received any packets from the server.) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.doCreateBean(AbstractAutowireCapableBeanFactory.java:519) at org.codehaus.groovy.grails.commons.spring.ReloadAwareAutowireCapableBeanFactory.doCreateBean(ReloadAwareAutowireCapableBeanFactory.java:129) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:450) at org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:290) at org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:222) at org.springframework.beans.factory.support.AbstractBeanFactory.doGetBean(AbstractBeanFactory.java:287) at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:193) at org.springframework.context.support.AbstractApplicationContext.initMessageSource(AbstractApplicationContext.java:714) at org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:404) at org.codehaus.groovy.grails.commons.spring.GrailsWebApplicationContext.refresh(GrailsWebApplicationContext.java:153) ... I get this error for a number of 'beans'. If I type mysql at my command prompt then I can easily login with the same credentials as my grails app which uses GORM and Hibernate to persist objects to the DB. I might not have given enough info to start with but I'm really interested to learn and will certainly provide it if asked, I just really don't know where to start on this one. Thanks, Gav

  Read the article

• Cannot exit X server, restart, shutdown or drop to tty when VGA monitor active

  - by terdon

  I have a strange problem. If I connect an external VGA monitor to my laptop, exiting the X environment in any way crashes the computer. For example, say I am working with my two monitors (the laptop's and one connected to my VGA port) active. Hitting Ctrl+Alt+F Key should take me down to a tty. What actually happens is that the VGA screen goes blank, as you would expect, but the laptop screen, although still on, shows nothing. I know the screen is on because it is slightly more illuminated than when it is off. When in this state, I can do nothing to regain access to the machine. I have tried: Ctrl+F Key (and even Ctrl+Alt+F Key, just in case) combinations and none seem to have any effect. Ctrl+Alt+Del : Nothing Magic SysRq key: Nothing Blindly typing my username and password and trying to reboot/shutdown or restart GDM or MDM: Nothing The only thing that works is a hard reset. The exact same behavior occurs when kiling the X server through Ctrl+Alt+Backspace, rebooting or shutdown. There is no difference if I reboot/shutdown/log out using the WM's graphical menu or if I use the shutdown or rebootcommands. It is also not WM-dependent. I have the same problem using Cinnamon, Gnome 3, MATE and xfce4. It is, however, VGA dependent. I have tried connecting another VGA monitor and have the same problem. I do not, however, have this problem if a screen is connected to the DisplayPort. It is, therefore, a VGA specific issue. To make things even stranger, this only occurs when both screens are active. If either the laptop screen or the VGA monitor is inactive the problem goes away. Finally, this problem arose when I installed the latest Linux Mint Debian (LMDE). It did not occur with the previous release of LMDE. I am not sure what has changed since I used the same kernel version in both releases (I had upgraded the kernel while on the previous release) and, I think, the same nvidia drivers. Oh, and yes, I have updated the nvidia driver. Hardware: Dell M4500 laptop CPU: Intel Core i7 RAM: 8GB Graphics: nVidia GT216 [Quadro FX 880M] Software: LMDE, kernel 3.2.0-2-amd64 Xorg: 1.11.4 nVidia kernel: 295.20-1+3.2.9-1 Possibly relevant files: /var/log/Xorg.0.log ~/.xsession-errors Does anyone have any ideas how to fix this? Thanks in advance for any help.

  Read the article

• Slow wifi from Windows Server 2003 virtualized in XenServer

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks! Update: The issue has been further narrowed down to Windows Server 2003, which Windows Home Server is based on, running in XenServer with the XenServer tools installed.

  Read the article

• Log - Server kernel: INFO: task httpd:000000 blocked for more than 120 seconds

  - by valter

  Almost everyday my server is crashing due to hight server load, and even restarting apache or mysql can't solve the problem. I need to reboot the server to solve, or it crash again due to the high load. The log system records something like this when it crashes: Aug 11 18:33:53 server kernel: INFO: task httpd:20008 blocked for more than 120 seconds. Aug 11 18:33:53 server kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 11 18:33:53 server kernel: httpd D ffffffff801538ac 0 20008 5816 20066 19809 (NOTLB) Aug 11 18:33:53 server kernel: ffff81025a299dc8 0000000000000082 ffff81033b4c0740 ffffffff80009a14 Aug 11 18:33:53 server kernel: ffff8101063f8d80 0000000000000009 ffff8100b758f7e0 ffff8101c57187e0 Aug 11 18:33:53 server kernel: 00009436d4100b6c 000000000001d50f ffff8100b758f9c8 000000083b531588 Aug 11 18:33:53 server kernel: Call Trace: Aug 11 18:33:53 server kernel: [<ffffffff80009a14>] __link_path_walk+0x173/0xfb9 Aug 11 18:33:53 server kernel: [<ffffffff8002cc16>] mntput_no_expire+0x19/0x89 Aug 11 18:33:53 server kernel: [<ffffffff80063c4f>] __mutex_lock_slowpath+0x60/0x9b Aug 11 18:33:53 server kernel: [<ffffffff80023908>] __path_lookup_intent_open+0x56/0x97 Aug 11 18:33:53 server kernel: [<ffffffff80063c99>] .text.lock.mutex+0xf/0x14 Aug 11 18:33:53 server kernel: [<ffffffff8001b21f>] open_namei+0xea/0x712 Aug 11 18:33:54 server kernel: [<ffffffff8002768a>] do_filp_open+0x1c/0x38 Aug 11 18:33:54 server kernel: Firewall: *UDP_IN Blocked* IN=eth1 OUT= MAC=ff:ff:ff:ff:ff:ff:00:30:48:9e:6e:99:08:00 SRC=208.43.135.158 DST=255.255.255.255 LEN=151 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=38354 DPT=6112 LEN=131 Aug 11 18:33:54 server kernel: [<ffffffff8001a061>] do_sys_open+0x44/0xbe Aug 11 18:33:54 server kernel: [<ffffffff8005d28d>] tracesys+0xd5/0xe0 I googled a lot trying to find a solution. But it looks that the solution is just to update the kernel or disk driver, thinks that I don't know how to do. In this url http://bugs.centos.org/view.php?id=4515 a lot o people report similar problems, except the fact that they are not related to httpd like mine. According to one member, one solution would be to add "elevator=noop " to /etc/grub.conf like in this example: title CentOS (2.6.18-238.12.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-238.12.1.el5xen ro root=/dev/VolGroup00/LogVol00 elevator=noop initrd /initrd-2.6.18-238.12.1.el5xen.img Would this really solve the problem? My disk are working in RAID. Can this cause some problem to my server? Is there any other solution?

  Read the article

• Blank displays after inactivity, mouse cursor not showing up

  - by Mike Christiansen

  I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

  Read the article

• Avoid read-write access to bad sectors on HDD to continue working on the HDD

  - by goldenmean

  I have a HP Pavilion dv6446 notebook. It had Windows Vista Home premium. After 4.5+ years of usage, just recently it started malfunctioning. While working fine, its screen goes white or sometimes some thin black lines horizontally. Laptop freezes. Hard reboot works. Again it works for some 2 hrs or so, same error. To diagnose I did run the Memory and Hard disk check which is present in the Bios Setup. Memory test passed. Hard disk test returned an error saying something like - "Replace the hard disk". Bad.. Some sectors or platters have gone bad on the disk. (I confirmed this later by further tests mentioned below) Then I tried installing a Ubuntu 11.10. It listed 3 partitions /dev/sda1, sda2, sda2. It again gave error and could not install grub loader on /dev/sda1. Bad sectors. Then redid the Ubuntu installation, this time asked to to install the Ubuntu on /dev/sda3. and kept /dev/sda1 for /home. Installed fine, and works fine as well. Due to unavailability of WiFi/ Ethernet driver for that adapters under Ubuntu( at least I could not configure them and get the networking working at all), I decided to go back to reinstall windows Vista. It did install fine. I did not have to format one data partition which has my data. I just formatted one partition which installed Windows So in effect HDD has not undergone a full format here. Worked ok for 1 day. But same white screen and freeze happened. Looks like while it is in use, it accesses the bad sectors for storing some data and that's when it bombs. I am inclined to think HDD has not failed fully or crashed but has developed bad sectors. Else if it was a HDD crash, it would have refused to boot at all let alone install on it. Questions: Is there any HDD test check under windows or any such tools windows/linux based ewhere which can identify the bad sectors of the HDD and 'lock/isolate' them from further read-write access of any kind. If not what are my options, if any to salvage this laptop HDD without replacing it. EDIT: Would the Disk Error checking tool under windows help in any way?

  Read the article

• Do RAID controllers commonly have SATA drive brand compatibility issues?

  - by Jeff Atwood

  We've struggled with the RAID controller in our database server, a Lenovo ThinkServer RD120. It is a rebranded Adaptec that Lenovo / IBM dubs the ServeRAID 8k. We have patched this ServeRAID 8k up to the very latest and greatest: RAID bios version RAID backplane bios version Windows Server 2008 driver This RAID controller has had multiple critical BIOS updates even in the short 4 month time we've owned it, and the change history is just.. well, scary. We've tried both write-back and write-through strategies on the logical RAID drives. We still get intermittent I/O errors under heavy disk activity. They are not common, but serious when they happen, as they cause SQL Server 2008 I/O timeouts and sometimes failure of SQL connection pools. We were at the end of our rope troubleshooting this problem. Short of hardcore stuff like replacing the entire server, or replacing the RAID hardware, we were getting desperate. When I first got the server, I had a problem where drive bay #6 wasn't recognized. Switching out hard drives to a different brand, strangely, fixed this -- and updating the RAID BIOS (for the first of many times) fixed it permanently, so I was able to use the original "incompatible" drive in bay 6. On a hunch, I began to assume that the Western Digital SATA hard drives I chose were somehow incompatible with the ServeRAID 8k controller. Buying 6 new hard drives was one of the cheaper options on the table, so I went for 6 Hitachi (aka IBM, aka Lenovo) hard drives under the theory that an IBM/Lenovo RAID controller is more likely to work with the drives it's typically sold with. Looks like that hunch paid off -- we've been through three of our heaviest load days (mon,tue,wed) without a single I/O error of any kind. Prior to this we regularly had at least one I/O "event" in this time frame. It sure looks like switching brands of hard drive has fixed our intermittent RAID I/O problems! While I understand that IBM/Lenovo probably tests their RAID controller exclusively with their own brand of hard drives, I'm disturbed that a RAID controller would have such subtle I/O problems with particular brands of hard drives. So my question is, is this sort of SATA drive incompatibility common with RAID controllers? Are there some brands of drives that work better than others, or are "validated" against particular RAID controller? I had sort of assumed that all commodity SATA hard drives were alike and would work reasonably well in any given RAID controller (of sufficient quality).

  Read the article

• Dovecot Virtual Users Not Authenticating

  - by blankabout

  We have a standard Postfix/Dovecot installation working perfectly with real users but cannot work out how to add virtual users, all virtual user login attempts fail with authentication errors. Following are snippets from the configuration files: /etc/postfix/main.cf: virtual_mailbox_domains = virtualexample.com virtual_mailbox_base = /var/spool/vhosts virtual_mailbox_recipients = hash:/etc/postfix/virtual_mailbox_recipients /etc/dovecot/dovecot.conf: !include conf.d/*.conf /etc/dovecot/conf.d/10-auth.conf auth_mechanisms = cram-md5 digest-md5 plain passdb { driver = passwd-file # Path for passwd-file. Also set the default password scheme. args = scheme=cram-md5 /etc/cram-md5.pwd } /etc/cram-md5.pwd [email protected]{MD5}$1$uIMvzy92$9Xt67B/qw4u6txkkxzne80 This is a snippet from the log when a login attempt is made: auth: Debug: Loading modules from directory: /usr/lib64/dovecot/auth auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libauthdb_ldap.so auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libdriver_sqlite.so auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libmech_gssapi.so auth: Debug: passwd-file /etc/cram-md5.pwd: Read 1 users auth: Debug: auth client connected (pid=21990) auth: Debug: client in: AUTH#0111#011CRAM-MD5#011service=imap#011lip=1.1.1.1#011rip=2.2.2.2#011lport=143#011rport=51774 auth: Debug: client out: CONT#0111#011PDI1Njc0NjQ1NzQ3MTY0NTkuMTM0MTIxNzkwN0BncDM+ auth: Debug: client in: CONT auth: Debug: passwd-file([email protected],2.2.2.2): lookup: [email protected] file=/etc/cram-md5.pwd auth: Debug: client out: OK#0111#[email protected] auth: Debug: master in: REQUEST#0111630404609#01121990#0111#011b66b5f46b520a08e1d19d3d249be7073 auth: Debug: passwd([email protected],2.2.2.2): lookup auth: passwd([email protected],2.2.2.2): unknown user auth: Error: userdb([email protected],2.2.2.2): user not found from userdb passwd auth: Debug: master out: NOTFOUND#0111630404609 imap: Error: Authenticated user not found from userdb, auth lookup id=1630404609 (client-pid=21990 client-id=1) imap-login: Internal login failure (pid=21990 id=1) (auth failed, 1 attempts): user=, method=CRAM-MD5, rip=2.2.2.2, lip=1.1.1.1, mpid=21993 auth: Debug: auth client connected (pid=22010) auth: Debug: client in: AUTH#0111#011CRAM-MD5#011service=imap#011lip=1.1.1.1#011rip=2.2.2.2#011lport=143#011rport=51775 auth: Debug: client out: CONT#0111#011PDcxMDkwNDY1NTQzODUzMDkuMTM0MTIxNzkyOEBncDM+ auth: Debug: client in: CONT auth: Debug: passwd-file([email protected],2.2.2.2): lookup: [email protected] file=/etc/cram-md5.pwd auth: Debug: client out: OK#0111#[email protected] auth: Debug: master in: REQUEST#011343539713#01122010#0111#011e47b1345784e2845d59e794afa9a6bbe auth: Debug: passwd([email protected],2.2.2.2): lookup auth: passwd([email protected],2.2.2.2): unknown user auth: Error: userdb([email protected],2.2.2.2): user not found from userdb passwd auth: Debug: master out: NOTFOUND#011343539713 imap: Error: Authenticated user not found from userdb, auth lookup id=343539713 (client-pid=22010 client-id=1) imap-login: Internal login failure (pid=22010 id=1) (auth failed, 1 attempts): user=, method=CRAM-MD5, rip=2.2.2.2, lip=1.1.1.1, mpid=22011 It would appear that the user lookup is not working, even tho' the log suggests that Dovecot is using the /etc/cram-md5.pwd file and the user is configured in that same file. There are of course dozens of examples of using virtual users with Dovecot, but all the ones we have found either refer to Dovecot 1.x (we are using 2.x), using only virtual users (we must use real AND virtual users) or want to use a MySQL db, we need to use a text file. Some hints about where we are going wrong would be very much appreciated.

  Read the article

• No login prompt displayed after updating Ubuntu 10.04, broken gdm

  - by cliff

  So here's what happens: I updated my system the other day, was prompted for a reboot for the update to complete but was in the middle of working so I delayed it until after I was done. I reboot and it's broken :(. It appears to boot normally, with the following exceptions: The purple Ubuntu load screen no longer displays (though it did for the first couple of times I tried to get in). I hear the login prompt sound, but no login prompt appears. Nor is it simply "invisible" - pressing enter, typing my password, and pressing enter again do nothing. Normally my Bluetooth mouse is functional at this point, but it is not. GRUB displays recovery options for my current kernel, and for an older one (2.6.32-24). Trying to boot into .32-24 gives me an error saying "udevadm can't do something while udev is not configured". So I try solutions listed here: http://superuser.com/questions/195786/ubuntu-update-went-wrong-pc-doesnt-boot-how-can-i-repair-it Nothing I tried seemed to work, and after further Googling my hunch is that it's a problem with gdm. Please correct me if I'm wrong, I don't know all that much about how Linux/Ubuntu systems work just yet. Things I'm able to do: Boot to a live CD Ctrl-Alt-F2 after that login sound plays brings me to a console login, which I can successfully do (it's how I tried the solutions above). This works only under the current kernel. A hack I'd be willing to explore is removing the login prompt from the console, but I'd prefer to "simply" fix what's wrong. Like that guy, I need to repair the system rather than reinstall. System: Dell Inspiron 1525 Core 2 Duo Proprietary Driver for Broadcom 43xx wireless Dual-boot with Windows 7 (which is how I'm posting this, unfortunately I only have this machine and any experimenting requires constant reboots into Windows/brokenbuntu) Last package installed was Moonlight, but it appeared to install properly. Kernel: 2.6.32-25 Edit: After working with Karl's suggestions, it seems that the problem is with gdm. Error exit status 245 when attempting to sudo apt-get install --reinstall gdm, also an error processing gdm when running sudo apt-get -f install. How do I reinstall or repair gdm so that I can get back into my machine?

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• DNS settings for resolving Host name to IP not working?

  - by Hasas Ali Khan

  I want to access my IIS hosted application over LAN. First I installed a DNS server. The DNS configuration steps are: Go to DNS Manager - right click on System Name - click on configure a DNS Server. DNS Server wizard open -, click on next button - Select radio button "forward lookup zone" click on next button. In the second window. click on radio button "The server maintains the zone" and then click next. Give the zone name "example.com" Click on radio button, "Do Not allow dynamic updates". and then click next button. In the next window, click on radio button "No it should not forward query" and then click next button. Complete the configure a DNS server wizard and then click on finish button. After it is managing the DNS records: In DNS server wizard. open tree of forward lookup zone and right click on the new zone name "example.com" - properties and click on "Start of authority" and write values on text boxes serial number=1 primary server=systemname.domainname responsible person=hostmaster.domainname Click on server name, highlight domain name, click on edit button and enter IP address of the server where I host my application. Highlight new zone name and right click on it and click "New Host" option. In this window there are three text boxes: Name(user parent name if blank)=scoring Fully Qualified Domain Name=scoring.example.com IP Address= My IP Address and check on "Create associated pointer(PTR) record" and click on "Add Host" Host button and then click done button. I have host header for my application is "scoring" on port 80 and its working fine on server my application setting are I have change its, Advance setting --> Application Pool Identity --> Local System application can access on server with host name "scoring" but it can not access on machines on LAN. When I change LAN machine host file that is under, C:/windows/system32/driver/etc/host and edit it and enter host name with hosted machine IP like this: scoring 192.168.1.20 By making these changes I can run the application over LAN machines as I mentioned above DNS setting by which I can run App over LAN with out editing the client's host file. What mistake am I doing in this configuration?

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• Hell: NTFS "Restore previous versions"...

  - by ttsiodras

  The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

  Read the article

• JNDI Datasource definition in Tomcat 6.0

  - by romaintaz

  I want to define a DataSource to an Oracle database on my Tomcat 6.0. So, in conf/server.xml (yes, I know that this DataSource will be available for all the webapps in Tomcat, but it's not a problem here), I've set this Resource: <GlobalNamingResources> <Resource name="hibernate/HibernateDS" auth="Container" type="javax.sql.DataSource" url="jdbc:oracle:thin:@myserver:1542:foo" username="foo" password="bar" driverClassName="oracle.jdbc.OracleDriver" maxActive="50" maxIdle="10" validationQuery="select 1 from dual"/> Then, in the web.xml of my application, I set a resource-ref element: <resource-ref> <description>Hibernate Datasource</description> <res-ref-name>hibernate/HibernateDS</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> Finally, as Hibernate is used to manage the database connection, I have a webapps/mywebapp/WEB-INF/classes/hibernate.cfg.xml that creates a session-factory using the JNDI DataSource: <hibernate-configuration> <session-factory> <property name="connection.datasource">java:comp/env/hibernate/HibernateDS</property> ... However, when I start my Tomcat server, I get an error that says it could not create the INFO [net.sf.hibernate.util.NamingHelper] JNDI InitialContext properties:{} INFO [net.sf.hibernate.connection.DatasourceConnectionProvider] Using datasource: java:comp/env/hibernate/HibernateDS INFO [net.sf.hibernate.transaction.TransactionFactoryFactory] Transaction strategy: net.sf.hibernate.transaction.JDBCTransactionFactory INFO [net.sf.hibernate.transaction.TransactionManagerLookupFactory] No TransactionManagerLookup configured (in JTA environment, use of process level read-write cache is not recommended) WARN [net.sf.hibernate.cfg.SettingsFactory] Could not obtain connection metadata org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot create JDBC driver of class '' for connect URL 'null' at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1150) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.getConnection(BasicDataSource.java:880) at net.sf.hibernate.connection.DatasourceConnectionProvider.getConnection(DatasourceConnectionProvider.java:59) at net.sf.hibernate.cfg.SettingsFactory.buildSettings(SettingsFactory.java:84) at net.sf.hibernate.cfg.Configuration.buildSettings(Configuration.java:1172) ... Caused by: java.lang.NullPointerException at sun.jdbc.odbc.JdbcOdbcDriver.getProtocol(JdbcOdbcDriver.java:507) at sun.jdbc.odbc.JdbcOdbcDriver.knownURL(JdbcOdbcDriver.java:476) at sun.jdbc.odbc.JdbcOdbcDriver.acceptsURL(JdbcOdbcDriver.java:307) at java.sql.DriverManager.getDriver(DriverManager.java:253) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1143) ... 11 more Do you have any idea why Hibernate is not able to construct the session-factory? What is wrong in my configuration?

  Read the article

• How to get physical partition name from iSCSI details on Windows?

  - by Barry Kelly

  I've got a piece of software that needs the name of a partition in \Device\Harddisk2\Partition1 style, as shown e.g. in WinObj. I want to get this partition name from details of the iSCSI connection that underlies the partition. The trouble is that disk order is not fixed - depending on what devices are connected and initialized in what order, it can move around. So suppose I have the portal name (DNS of the iSCSI target), target IQN, etc. I'd like to somehow discover which volumes in the system relate to it, in an automated fashion. I can write some PowerShell WMI queries that get somewhat close to the desired info: PS> get-wmiobject -class Win32_DiskPartition NumberOfBlocks : 204800 BootPartition : True Name : Disk #0, Partition #0 PrimaryPartition : True Size : 104857600 Index : 0 ... From the Name here, I think I can fabricate the corresponding name by adding 1 to the partition number: \Device\Harddisk0\Partition1 - Partition0 appears to be a fake partition mapping to the whole disk. But the above doesn't have enough information to map to the underlying physical device, unless I take a guess based on exact size matching. I can get some info on SCSI devices, but it's not helpful in joining things up (iSCSI target is Nexenta/Solaris COMSTAR): PS> get-wmiobject -class Win32_SCSIControllerDevice __GENUS : 2 __CLASS : Win32_SCSIControllerDevice ... Antecedent : \\COBRA\root\cimv2:Win32_SCSIController.DeviceID="ROOT\\ISCSIPRT\\0000" Dependent : \\COBRA\root\cimv2:Win32_PnPEntity.DeviceID="SCSI\\DISK&VEN_NEXENTA&PROD_COMSTAR... Similarly, I can run queries like these: PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_TargetClass PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_PersistentDevices These guys return information relating to my iSCSI target name and the GUID volume name respectively (a volume name like \\?\Volume{guid-goes-here}), but the GUID volume name is no good to me, and there doesn't appear to be a reliable correspondence between the target name and the volume that I can join on. I simply can't find an easy way of getting from an IQN (e.g. iqn.1992-01.com.example:storage:diskarrays-sn-a8675309) to physical partitions mapped from that target. The way I do it by hand? I start Disk Management, and look for a partition of the correct size, verify that its driver says NEXENTA COMSTAR, and look at the disk number. But even this is unreliable if I have multiple iSCSI volumes of the exact same size. Any suggestions?

  Read the article

• Postfix to deliver mail to a virtual address mailbox

  - by Chloe

  Postfix version 2.6.6, Dovecot Version 2.0.9 I want to setup Postfix + Dovecot. Dovecot seems to be working. I can authenticate. However, the mailbox is empty! Nothing will get delivered! I followed many tutorials on Postfix + Dovecot but they seem to want to complicate things by using Dovecot LDA or MySQL. I just want it to be very simple and having Postfix deliver to the virtual mail boxes are fine. I don't need MySQL either. I already set up a custom password file that Dovecot uses for authentication and I can login to POP3 with SSL. I can see from the logs that Postfix is delivering to the system user accounts (the catch-all), instead of the virtual users that I set up in Dovecot. The SMTP + SSL authentication seems to work also. I can also see from the logs that Dovecot is checking the correct virtual mail folder. I just need to figure out how to get Postfix to deliver to the virtual mail boxes. I have the following which I believe are relevant. Let me know what other settings you need to see: alias_maps = hash:/etc/aliases mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = xxx.com myhostname = mail.xxx.com mynetworks = 99.99.99.99, 99.99.99.99 myorigin = $mydomain relay_domains = $mydestination, xxx.com, domain2.net, domain3.com sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = reject_non_fqdn_sender reject_non_fqdn_recipient reject_unknown_recipient_domain permit_sasl_authenticated check_relay_domains smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_sender_restrictions = check_sender_mx_access cidr:/etc/postfix/bogus_mx reject_invalid_hostname reject_unknown_sender_domain reject_non_fqdn_sender virtual_mailbox_base = /var/spool/vmail virtual_mailbox_domains = xxx.com, domain2.net, domain3.com virtual_minimum_uid = 444 Postfix master.cf: submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_sasl_type=dovecot -o smtpd_sasl_path=private/auth -o smtpd_sasl_security_options=noanonymous -o smtpd_sasl_local_domain=$myhostname -o smtpd_client_restrictions=permit_sasl_authenticated,reject -o smtpd_sender_login_maps=hash:/etc/postfix/virtual -o smtpd_sender_restrictions=reject_sender_login_mismatch -o smtpd_recipient_restrictions=reject_non_fqdn_recipient,reject_unknown_recipient_domain,permit_sasl_authenticated,reject Dovecot related: mail_location = maildir:~/Maildir passdb { args = /etc/dovecot/users.conf driver = passwd-file } service auth { unix_listener /var/spool/postfix/private/auth { mode = 0660 user = postfix } } The virtual mail user: vmail:x:444:99:virtual mail users:/var/spool/vmail:/sbin/nologin Here is the /var/log/maillog when I try to send something to myself: Oct 25 22:10:05 308321 postfix/smtpd[2200]: connect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:05 308321 postfix/smtpd[2200]: D224BD4753: client=user-999.cable.mindspring.com[99.99.99.99], sasl_method=LOGIN, [email protected] Oct 25 22:10:06 308321 postfix/cleanup[2207]: D224BD4753: message-id=<7DC3C163CFFC483AB6226F8D3D9969D2@dumbopc> Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: from=<[email protected]>, size=1385, nrcpt=1 (queue active) Oct 25 22:10:06 308321 postfix/smtpd[2200]: disconnect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:06 308321 postfix/local[2208]: D224BD4753: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=1.1, delays=0.53/0.02/0/0.51, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: removed

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• JNDI Datasource definition in Tomcat 6.0

  - by romaintaz

  Hi all, I want to define a DataSource to an Oracle database on my Tomcat 6.0. So, in conf/server.xml (yes, I know that this DataSource will be available for all the webapps in Tomcat, but it's not a problem here), I've set this Resource: <GlobalNamingResources> <Resource name="hibernate/HibernateDS" auth="Container" type="javax.sql.DataSource" url="jdbc:oracle:thin:@myserver:1542:foo" username="foo" password="bar" driverClassName="oracle.jdbc.OracleDriver" maxActive="50" maxIdle="10" validationQuery="select 1 from dual"/> Then, in the web.xml of my application, I set a resource-ref element: <resource-ref> <description>Hibernate Datasource</description> <res-ref-name>hibernate/HibernateDS</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> Finally, as Hibernate is used to manage the database connection, I have a webapps/mywebapp/WEB-INF/classes/hibernate.cfg.xml that creates a session-factory using the JNDI DataSource: <hibernate-configuration> <session-factory> <property name="connection.datasource">java:comp/env/hibernate/HibernateDS</property> ... However, when I start my Tomcat server, I get an error that says it could not create the INFO [net.sf.hibernate.util.NamingHelper] JNDI InitialContext properties:{} INFO [net.sf.hibernate.connection.DatasourceConnectionProvider] Using datasource: java:comp/env/hibernate/HibernateDS INFO [net.sf.hibernate.transaction.TransactionFactoryFactory] Transaction strategy: net.sf.hibernate.transaction.JDBCTransactionFactory INFO [net.sf.hibernate.transaction.TransactionManagerLookupFactory] No TransactionManagerLookup configured (in JTA environment, use of process level read-write cache is not recommended) WARN [net.sf.hibernate.cfg.SettingsFactory] Could not obtain connection metadata org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot create JDBC driver of class '' for connect URL 'null' at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1150) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.getConnection(BasicDataSource.java:880) at net.sf.hibernate.connection.DatasourceConnectionProvider.getConnection(DatasourceConnectionProvider.java:59) at net.sf.hibernate.cfg.SettingsFactory.buildSettings(SettingsFactory.java:84) at net.sf.hibernate.cfg.Configuration.buildSettings(Configuration.java:1172) ... Caused by: java.lang.NullPointerException at sun.jdbc.odbc.JdbcOdbcDriver.getProtocol(JdbcOdbcDriver.java:507) at sun.jdbc.odbc.JdbcOdbcDriver.knownURL(JdbcOdbcDriver.java:476) at sun.jdbc.odbc.JdbcOdbcDriver.acceptsURL(JdbcOdbcDriver.java:307) at java.sql.DriverManager.getDriver(DriverManager.java:253) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1143) ... 11 more Do you have any idea why Hibernate is not able to construct the session-factory? What is wrong in my configuration?

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

  - by Vlad Fedin

  One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

  Read the article

• Computer freezes +/- 30 seconds, suspicion on SSD

  - by Robert vE

  My computer freezes for about 30 seconds, this happens occasionally. When it happens I can still move the mouse, sometimes even alternate between tabs in google chrome. If I try to open windows explorer nothing happens. Also chrome rapports "waiting for cache". It also happens in starcraft II, during which the sounds loops. I have made a Trace as this topic describes: How do I troubleshoot a Windows 7 freeze or slowness? Trace: https://docs.google.com/open?id=0B_VkKdh535p6NklhSDdBLURUMnc I have looked at it, but I couldn't figure it out. My system specs are: AMD Athlon X4 651 Asus Ati HD6670 ADATA SSD sp900 Asus f1a55 mainboard 4 GB crucial 1333 ram 500 watt atx ps I'm running Windows 7, fully updated. Any help is much appreciated. Update: I tried something before your reply that may have helped the problem. I don't know for sure if it has, it's too soon to tell. A bit of history first. I had problems installing win7 on my ssd from the start. In IDE mode it worked, but I had the same problems as above. AHCI was a total fail, with it on before install as well as turning it on after install (including tweaking register). I didn't bother installing the AMD chipset/AHCI as it was reported to have no TRIM function and thus make problems worse. Eventually I did install the AMD SMbus driver as the stability issues were driving me crazy. It worked, no more issues, until I installed some extra drivers and software. Audio/LAN/ASUS suite, I don’t see the relation, but somehow it screwed up my system again. As a last effort I posted here on this site. After which the thought occurred to me turn on AHCI again as by now I had all necessary drivers installed anyway. (plus all windows updates downloaded/installed in the meantime) I did and stability didn’t seem great the first few reboots, but eventually everything seemed to work great. I tried to play starcraft II – an almost guaranteed freeze before – and I had no problems. I’m basically crossing my fingers and hope the problem is gone for good. I still think it has something to do with my SSD. In my research into the problem I noticed a lot of these issues with sandforce 2281 firmware, the exact same firmware I have. People reported the same problem that I had, freezes. Additionally they reported that during a freeze the hdd light stayed on, I noticed after I read this that this happened with my computer as well. None of this is conclusive evidence that my SSD is really to fault, but it is suspicious. And why turning on AHCI would fix it I don’t know. Thank you Tom for taking a look, if the problem returns I will certainly do what you advised.

  Read the article

< Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >