Search Results

Search found 7821 results on 313 pages for 'high dpi'.

Page 275/313 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

  • Vagrant-aws not provisioning

    - by SuperCabbage
    I'm trying to spin up and provision an EC2 instance with Vagrant, it successfully creates the instance up and I can then use vagrant ssh to SSH into the it but Puppet doesn't seem to carry out any provisioning. Upon running vagrant up --provider=aws --provision I get the following output Bringing machine 'default' up with 'aws' provider... WARNING: Nokogiri was built against LibXML version 2.8.0, but has dynamically loaded 2.9.1 [default] Warning! The AWS provider doesn't support any of the Vagrant high-level network configurations (`config.vm.network`). They will be silently ignored. [default] Launching an instance with the following settings... [default] -- Type: m1.small [default] -- AMI: ami-a73264ce [default] -- Region: us-east-1 [default] -- Keypair: banderton [default] -- Block Device Mapping: [] [default] -- Terminate On Shutdown: false [default] Waiting for SSH to become available... [default] Machine is booted and ready for use! [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/ => /vagrant [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/manifests/ => /tmp/vagrant-puppet/manifests [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/modules/ => /tmp/vagrant-puppet/modules-0 [default] Running provisioner: puppet... An error occurred while executing multiple actions in parallel. Any errors that occurred are shown below. An error occurred while executing the action on the 'default' machine. Please handle this error then try again: No error message I can then SSH into the instance by using vagrant ssh but none of my provisioning has taken place, so I'm assuming that errors have occured but I'm not being given any useful information relating to them. My Vagrantfile is as following; Vagrant.configure("2") do |config| config.vm.box = "ubuntu_aws" config.vm.box_url = "https://github.com/mitchellh/vagrant-aws/raw/master/dummy.box" config.vm.provider :aws do |aws, override| aws.access_key_id = "REDACTED" aws.secret_access_key = "REDACTED" aws.keypair_name = "banderton" override.ssh.private_key_path = "~/.ssh/banderton.pem" override.ssh.username = "ubuntu" aws.ami = "ami-a73264ce" end config.vm.provision :puppet do |puppet| puppet.manifests_path = "manifests" puppet.module_path = "modules" puppet.options = ['--verbose'] end end My Puppet manifest is as following; package { [ 'build-essential', 'vim', 'curl', 'git-core', 'nano', 'freetds-bin' ]: ensure => 'installed', } None of the packages are installed.

    Read the article

  • Scoping a home dev server

    - by AbhikRK
    Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance

    Read the article

  • Looking for Fiddler2 help. connection to gateway refused? Just got rid of a virus

    - by John Mackey
    I use Fiddler2 for facebook game items, and it's been a great success. I accessed a website to download some dat files I needed. I think it was eshare, ziddu or megaupload, one of those. Anyway, even before the rar file had downloaded, I got this weird green shield in the bottom right hand corner of my computer. It said a Trojan was trying to access my computer, or something to that extent. It prompted me to click the shield to begin anti-virus scanning. It turns out this rogue program is called Antivirus System Pro and is pretty hard to get rid of. After discovering the rogue program, I tried using Fiddler and got the following error: [Fiddler] Connection to Gateway failed.Exception Text: No connection could be made because the target machine actively refused it 127.0.0.1:5555 I ended up purchasing SpyDoctor + Antivirus, which I'm told is designed specifically for getting rid of these types of programs. Anyway, I did a quick-scan last night with spydoctor and malware bytes. Malware picked up 2 files, and Spydoctor found 4. Most were insignificant, but it did find a worm called Worm.Alcra.F, which was labeled high-priority. I don’t know if that’s the Anti-Virus Pro or not, but SpyDoctor said it got rid of all of those successfully. I tried to run Fiddler again before leaving home, but was still getting the "gateway failed" error. Im using the newest version of firefox. When I initially set up the Fiddler 2.2.8.6, I couldn’t get it to run at first, so I found this faq on the internet that said I needed to go through ToolsOptionsSettings and set up an HTTP Proxy to 127.0.0.1 and my Port to 8888. Once I set that up and downloaded this fiddler helper as a firefox add-on, it worked fine. When I turn on fiddler, it automatically takes my proxy setting from no proxy (default) to the 127.0.0.1 with Port 8888 set up. It worked fine until my computer detected this virus. Anyway, hopefully I've given you sufficient information to offer me your best advice here. Like I said, Spydoctor says the bad stuff is gone, so maybe the rogue program made some type of change in my fiddler that I could just reset or uncheck or something like that? Or will I need to completely remove fiddler and those dat files and rar files I downloaded? Any help would be greatly appreciated. Thanks for your time.

    Read the article

  • Scoping a home dev server

    - by AbhikRK
    Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance Have posted this question previously on SuperUser but no responses yet. So was wondering if this is a more apt forum for this.

    Read the article

  • Varnish 503 Guru Mediation errors with pfsense and healthy apache

    - by Fammy
    We are running a pfsense firewall / load balancer with varnish as service, In front of Fedora linux webservers running apache. We are getting intermittent 503 guru mediation errors. We are a bit stuck scratching our heads because it is not easily repeatable. The timeouts are set to 30s (connect and first byte) but yet the 503 page will show instantly, not after 30s. Then if you refresh immediately it may very well work instantly and sometimes for a 100 refreshes. The load average on the web servers is < 1, the DB server is < 3 (all servers (web, db, pfsense/varnish) are physical rather than VM. I would have thought if the timeouts were being hit then the 503 page would only appear after 30s am I mistaken? Also when an error happens there does not appear to be any corresponding error in apache's log files. This seems to affect pages as well as images, so it is possible to have the page load fine, and for 9/10 images on the page to be fine but 1 not work An example of the varnish debug is below. It says no backend connection but I can't figure out why, if the load was high on apache I could understand it being flaky The machines are on the same gig ethernet lan 21 ReqStart c *IP-REMOVED* 33418 1274368062 21 RxRequest c GET 21 RxURL c /fashion/ 21 RxProtocol c HTTP/1.1 21 RxHeader c User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.0.5) Gecko/2008121622 Fedora/3.0.5-1.fc10 Firefox/3.0.5 21 RxHeader c Host: *ourdomain.com* 21 RxHeader c Accept: */* 21 RxHeader c Accept-Encoding: deflate, gzip 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error deliver 21 VCL_call c deliver deliver 21 TxProtocol c HTTP/1.1 21 TxStatus c 503 21 TxResponse c Service Unavailable 21 TxHeader c Server: Varnish 21 TxHeader c Content-Type: text/html; charset=utf-8 21 TxHeader c Content-Length: 384 21 TxHeader c Accept-Ranges: bytes 21 TxHeader c Date: Wed, 11 Apr 2012 10:36:17 GMT 21 TxHeader c X-Varnish: 1274368062 21 TxHeader c Age: 0 21 TxHeader c Via: 1.1 varnish 21 TxHeader c Connection: close 21 TxHeader c X-Cache: MISS 21 Length c 384 21 ReqEnd c 1274368062 1334140577.449995041 1334140577.450334787 1.794108152 0.000282764 0.000056982

    Read the article

  • usb_modeswitch not switching

    - by deniz
    After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

    Read the article

  • Win7 x64 unresponsive for a minute or so. HD failing?

    - by Gaia
    On a fully updated Win7 x64, every so often the system stalls for a minute or so. This has been going on for a couple months now. By stalling I mean the mouse responds and I can move windows around, but any window, any program, that is open becomes whiteish when I select it AND any new programs will not open. It doesn't matter what kind of program it is. When the stall stops all clicks I made (open new programs for example) take effect. Nothing shows up consistently (as in every time this happens) in the event log. Today though I was able to find something, but it doesn't reveal much other than the "system was unresponsive". It's a 7009 for "A timeout was reached (30000 milliseconds) while waiting for the Windows Error Reporting Service service to connect." It doesn't matter if I have any USB devices plug-in or not. I've ran Microsoft Security Essentials and Malwarebytes. While the machine is unresponsive, I've noticed that Drive D (the other partition on the single internal HD in this laptop) is displayed like this in explorer. This never occurs with Drive C or any other drive on the machine. . SMART report for the physical drive: Read benchmark by HD Tune 5 Pro, probably the most telling piece of the puzzle. Isn't this alone enough to see there is a problem with the drive, regardless of whether the unresponsiveness is caused by such purported problem? Here is a short hardware report: Computer: LENOVO ThinkPad T520 CPU: Intel Core i5-2520M (Sandy Bridge-MB SV, J1) 2500 MHz (25.00x100.0) @ 797 MHz (8.00x99.7) Motherboard: LENOVO 423946U Chipset: Intel QM67 (Cougar Point) [B3] Memory: 8192 MBytes @ 664 MHz, 9.0-9-9-24 - 4096 MB PC10600 DDR3 SDRAM - Samsung M471B5273CH0-CH9 - 4096 MB PC10600 DDR3 SDRAM - Patriot Memory (PDP Systems) PSD34G13332S Graphics: Intel Sandy Bridge-MB GT2+ - Integrated Graphics Controller [D2/J1/Q0] [Lenovo] Intel HD Graphics 3000 (Sandy Bridge GT2+), 3937912 KB Drive: ST320LT007, 312.6 GB, Serial ATA 3Gb/s Sound: Intel Cougar Point PCH - High Definition Audio Controller [B2] Network: Intel 82579LM (Lewisville) Gigabit Ethernet Controller Network: Intel Centrino Advanced-N 6205 AGN 2x2 HMC OS: Microsoft Windows 7 Professional (x64) Build 7601 The drive less than 1 year old. Do I have a defective drive? Seagate Tools diag says there is nothing wrong with the drive... UPDATE: I noticed that the windows error reporting service entered the running state then the stopped state and the space between the two events was exactly 2 minutes. Which error it was trying to report I don't know. I check the "Reliability Monitor" and it shows no errors to be reported. I've disabled the windows error reporting service to see if the problem stops.

    Read the article

  • phpMyAdmin causes php-fpm worker to restart (502 Bad Gateway)

    - by rndbit
    I am trying to set up a test site for myself. Everything works fine except phpMyAdmin. php installation loads my test site scripts, they work fine, however trying to load phpMyAdmin i get 502 Bad Gateway error. Judging from logs (that are not too helpful) it seems that php-fpm worker is crashing each time phpmyadmin is being accessed. No clue how or why.. Does anyone have any idea? nginx log: *3 recv() failed (104: Connection reset by peer) while reading response header from upstream, And php-fpm log: [07-Jun-2012 14:19:51] WARNING: [pool www] child 32179 exited on signal 11 (SIGSEGV) after 3.217902 seconds from start [07-Jun-2012 14:19:51] NOTICE: [pool www] child 32351 started My nginx conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; fastcgi_buffers 8 16k; fastcgi_buffer_size 32k; include /etc/nginx/conf.d/*.conf; server { listen 443 ssl; listen 80; server_name testsite.net www.testsite.net; ssl on; ssl_certificate /var/www/html/admin/ssl/certificate.pem; ssl_certificate_key /var/www/html/admin/ssl/privatekey.pem; ssl_session_timeout 1m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5:!kEDH; ssl_prefer_server_ciphers on; access_log off; location ~ \.php$ { root /var/www/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; } location / { root /var/www/html; index index.php; } } } php.ini is standard, with cgi.fix_pathinfo=0 php-fpm.conf: include=/etc/php-fpm.d/*.conf [global] pid = /var/run/php-fpm/php-fpm.pid error_log = /var/log/php-fpm/error.log log_level = notice php-fpm.d/www.conf: [www] listen = 127.0.0.1:9000 listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 10 pm.start_servers = 1 pm.min_spare_servers = 1 pm.max_spare_servers = 10 slowlog = /var/log/php-fpm/www-slow.log php_flag[display_errors] = on php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on

    Read the article

  • Ubuntu Server 12.04 CPU Load

    - by zertux
    I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

    Read the article

  • Network use of Gaming PC

    - by Matthew Patrick Cashatt
    Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

    Read the article

  • Looking for Fiddler2 help. connection to gateway refused...just got rid of a virus?

    - by john mackey
    I use Fiddler2 for facebook game items, and it's been a great success. I accessed a website to download some dat files I needed. I think it was eshare, ziddu or megaupload, one of those. Anyway, even before the rar file had downloaded, I got this weird green shield in the bottom right hand corner of my computer. It said a Trojan was trying to access my computer, or something to that extent. It prompted me to click the shield to begin anti-virus scanning. It turns out this rogue program is called Antivirus System Pro and is pretty hard to get rid of. After discovering the rogue program, I tried using Fiddler and got the following error: [Fiddler] Connection to Gateway failed. Exception Text: No connection could be made because the target machine actively refused it 127.0.0.1:5555 I ended up purchasing SpyDoctor + Antivirus, which I'm told is designed specifically for getting rid of these types of programs. Anyway, I did a quick-scan last night with spydoctor and malware bytes. Malware picked up 2 files, and Spydoctor found 4. Most were insignificant, but it did find a worm called Worm.Alcra.F, which was labeled high-priority. I don’t know if that’s the Anti-Virus Pro or not, but SpyDoctor said it got rid of all of those successfully. I tried to run Fiddler again before leaving home, but was still getting the "gateway failed" error. Im using the newest version of firefox. When I initially set up the Fiddler 2.2.8.6, I couldn’t get it to run at first, so I found this faq on the internet that said I needed to go through ToolsOptionsSettings and set up an HTTP Proxy to 127.0.0.1 and my Port to 8888. Once I set that up and downloaded this fiddler helper as a firefox add-on, it worked fine. When I turn on fiddler, it automatically takes my proxy setting from no proxy (default) to the 127.0.0.1 with Port 8888 set up. It worked fine until my computer detected this virus. Anyway, hopefully I've given you sufficient information to offer me your best advice here. Like I said, Spydoctor says the bad stuff is gone, so maybe the rogue program made some type of change in my fiddler that I could just reset or uncheck or something like that? Or will I need to completely remove fiddler and those dat files and rar files I downloaded? Any help would be greatly appreciated. Thanks for your time.

    Read the article

  • Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

    - by Pro Backup
    In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

    Read the article

  • MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

    - by user88114
    This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

    Read the article

  • Linux per-process resource limits - a deep Red Hat Mystery

    - by BobBanana
    I have my own multithreaded C program which scales in speed smoothly with the number of CPU cores.. I can run it with 1, 2, 3, etc threads and get linear speedup.. up to about 5.5x speed on a 6-core CPU on a Ubuntu Linux box. I had an opportunity to run the program on a very high end Sunfire x4450 with 4 quad-core Xeon processors, running Red Hat Enterprise Linux. I was eagerly anticipating seeing how fast the 16 cores could run my program with 16 threads.. But it runs at the same speed as just TWO threads! Much hair-pulling and debugging later, I see that my program really is creating all the threads, they really are running simultaneously, but the threads themselves are slower than they should be. 2 threads runs about 1.7x faster than 1, but 3, 4, 8, 10, 16 threads all run at just net 1.9x! I can see all the threads are running (not stalled or sleeping), they're just slow. To check that the HARDWARE wasn't at fault, I ran SIXTEEN copies of my program independently, simultaneously. They all ran at full speed. There really are 16 cores and they really do run at full speed and there really is enough RAM (in fact this machine has 64GB, and I only use 1GB per process). So, my question is if there's some OPERATING SYSTEM explanation, perhaps some per-process resource limit which automatically scales back thread scheduling to keep one process from hogging the machine. Clues are: My program does not access the disk or network. It's CPU limited. Its speed scales linearly on a single CPU box in Ubuntu Linux with a hexacore i7 for 1-6 threads. 6 threads is effectively 6x speedup. My program never runs faster than 2x speedup on this 16 core Sunfire Xeon box, for any number of threads from 2-16. Running 16 copies of my program single threaded runs perfectly, all 16 running at once at full speed. top shows 1600% of CPUs allocated. /proc/cpuinfo shows all 16 cores running at full 2.9GHz speed (not low frequency idle speed of 1.6GHz) There's 48GB of RAM free, it is not swapping. What's happening? Is there some process CPU limit policy? How could I measure it if so? What else could explain this behavior? Thanks for your ideas to solve this, the Great Xeon Slowdown Mystery of 2010!

    Read the article

  • How to install missing Sound Drivers in Ubuntu?

    - by Sakamoto Kazuma
    I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

    Read the article

  • networked storage for a research group, 10-100 TB

    - by Marc
    this is related to this post: http://serverfault.com/questions/80854/scalable-24-tb-nas-for-research-department but perhaps a little more general. Background: We're a research lab of around 10 people who do a lot of experiments that involve taking pictures at one of several lab setups and then analyzing it an one of several lab computers. Each experiment may produce 2 or 3 GB of data, and we are generating data at the rate of about 10 TB/year. Right now, we are storing the data on a 6-bay netgear readynas pro, but even with 2 TB drive, this only gives us 10 TB of storage. Also, right now we are not backing up at all. Our short term backup plan is to get a second readynas, put it in a different building and mirror the one drive onto the other. Obviously, this is somewhat non-ideal. Our options: 1) We can pay our university $400/ TB /year for "backed up" online storage. We trust them more than we trust us, but not a whole lot. 2) We can continue to buy small NASs and mirror them between offices. One limit, although stupid, is that we don't have an unlimited number of ethernet jacks. 3) We can try to implement our own data storage solution, which is why I'm asking you guys. One thing to consider is that we're a very transient population and none of us are network administration experts. I will probably be here only another year or so, and graduate students, who are here the longest, have a 5-6 year time scale. So nothing can require expert oversight. Our data transfer rates are low - most of the data will just sit on the server waiting for someone to look at it once or twice - so we don't need a really high speed system. Given these contraints, can someone recommend a fairly low-cost, scalable, more or less turn key shared data storage system with backup in a separate physical location. Does such a thing exist or should we just pay the university to take care of it for us? As a second question, our professor just got tenure and is putting together a budget. Here the goal is to ask for as much as you can and hope you get a fraction of it. So the same question, minus the low-cost. Without budget constraints, can you recommend a scalable turn-key backed up storage system. Thanks

    Read the article

  • Linksys WiFi usb dongle and linux woes

    - by MrStatic
    I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

    Read the article

  • Adaptec 5805 not recognized after reboot

    - by Rakedko ShotGuns
    After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

    Read the article

  • OS X server large scale storage and backup

    - by user135217
    I really hope this question doesn't come across as trolling or asking for buying advice. It's not intended. I've just started working for a small ad agency (40 employees). I actually quit being a system administrator a few years ago (too stressful!), but the company we're currently outsourcing our IT stuff to is doing such a bad job that I've felt compelled to get involved and do what I can to improve things. At the moment, all the company's data is stored on an 8TB external firewire drive attached to a Mac Mini running OS X Server 10.6, which provides filesharing (using AFP) for the whole company. There is a single backup drive, which is actually a caddy containing two 3TB hard drives arranged in RAID 0 (arrggghhhh!), which someone brings in as and when and copies over all the data using Carbon Copy Cloner. That's the entirety of the infrastructure, and the whole backup and restore strategy. I've been having sleepless nights. I've just started augmenting the backup process with FreeBSD, ZFS, sparse bundles and snapshot sends to get everything offsite. I think this is a workable behind the scenes solution, but for people's day to day use I'm struggling. Given the quantity and importance of the data, I think we should really be looking towards enterprise level storage solutions, high availability and so on, but the whole company is all Mac all the time, and I cannot find equipment that will do what we need. No more Xserve; no rack storage; no large scale storage at all apart from that Pegasus R6 that doesn't seem all that great; the Mac Pro has fibre channel, but it's not a real server and it's ludicrously expensive; Xsan looks like it's on the way out; things like heartbeatd and failoverd have apparently been removed from Lion Server; the new Mac Mini only has thunderbolt which severely limits our choices; the list goes on and on. I'm really, really not trying to troll here. I love Macs, but I just genuinely don't know where I'm supposed to look for server stuff. I have considered Linux or FreeBSD and netatalk for serving files with all the server-y goodness those OSes bring, but some the things I've read make me wonder if it's really the way to go. Also, in my own (admittedly quite cursory) experiments with it, I've struggled to get decent transfer speeds. I guess there's also the possibility of switching everyone off AFP and making them use SMB or NFS, but I understand that this can cause big problems with resource forks and file locks. I figure there must be plenty of all Mac companies out there. If you're the sysadmin at one, what do you use? Any suggestions very gratefully received.

    Read the article

  • Plesk Postfix Mail Server 9.5.4 very heavy load, 1000s of processes

    - by Eugene van der Merwe
    Our Plesk Linux Ubuntu 64-bit mail server has extremely high load and we don't know how to isolate it. The load was okay will two weeks ago but in the last two weeks it's seriously deteriorated. The mail server has been running for years and we have had sporadic performance issues. Normally we reduce the load by turning off all SPAM checks until the problem is sorted (which sometimes resolves itself). Currently we have turned of real time block lists, SPF checking and we have attempted to turn off SpamAssassin. No matter what we do the SpamAssassin check box stays ticked in the GUI. Out of desperation we have done /etc/init.d/psa-spamassassin stop. For years we haven't been able to do SpamAssassin because it kills the server. We would like to use it but performance is more important for now. We cannot turn off Greylisting. The moment we turn off Greylisting our help desk is inandated with calls. Out of desperation we investigated truncating the Greylisting database which is now 2.5 GB big but we abandoned this after noticing turning of Greylisting doesn't improve the performance at all. We have no anti-virus. It's just more load and Dr. Web never really worked that well for us. But we'll try that if it will make a difference. We have implemented Postfix Anvil. This seems to have made the situation worse so we disabled it. We’re not sure if this is the case. Our current mail server is configured to forward all SMTP to a relay server. We did so to reduce the load. This helped a lot because outgoing queues are generally empty. We are running in an Expand configuration. The mail server has about 12 000 accounts of which maybe half are active. We have read through this document: http://www.postfix.org/STRESS_README.html but there are too many settings and we don’t know which ones to choose. Please assist urgently. We need advice on how to fix this problem before all our clients abandon is. The only clue we have is that there are 100s of these processes: 30 13205 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13207 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13208 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13209 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13213 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue

    Read the article

  • How can I fix Problems with interlaced video jerking/flicking when playedback on DVD players? (Mixin

    - by Simon P Stevens
    I'm trying to make a DVD and the final DVD jerks when played on standalone DVD players. It seems to play fine on PCs. I think the problem may be to do with interlacing settings when rendering the final output, but I'll outline the whole editing process I have followed in case I've made a mistake somewhere else. Most of the footage comes from a sony handy cam (one of those mini DVD ones) so isn't great quality. It was set to "high quality" (haha) and 16:9 aspect ratio when it was recorded. I copy the files directly from the mini DVDs onto the hard drive and import them into Cinelerra. In Cinelerra I set the format to 25fps, 720x576, RGBA-8bit, 16:9, interlaced bottom fields first. When I've finished the editing, I add a Fields to frames effect (set to bottom first) to each video track. I render to audio and video separately: Audio: AC3, 128kbps Video: YUV4MPEG steam, video pipe settings: ffmpeg -f yuv4mpegpipe -i - -y -target dvd -flags +ilme+ildct mpeg2video % Cinelerra often crashes during the rendering, so I set it to generate a new video file at each label, and combine them using cat when I've got a sucesful render of each one. Once I've combined them, I use mencoder to re-index them: mencoder -forceidx -oac copy -ovc copy merged.m2v -o mergedReIndexed.m2v I combine the audio and video files using ffmpeg: ffmpeg -i AudioFile.ac3 -i VideoFile.m2v -target dvd -flags +ilme+ildct FinalMovie.mpg Then I build the menus with spumux and I create the DVD file system with dvdauthor, and finally I write it do a dvd-r like this: nice -n -20 growisofs -dvd-compat -speed=2 -Z /dev/dvd -dvd-video -V VIDEO ./ && eject /dev/dvd Originally, when I did it the DVD flickered badly, so as suggested in a guide I added the fields to frames effect in cinelerra. Now it doesn't "flicker", but has become "jerky" when there is lots of motion, particularly when the camera is moving, so the whole background moves. This is what I've tried so far: Removed "mpeg2video" from cinelerra video render pipe. Removed +ilme from render pipe. Removed +ildct from render pipe. Removed +ilme from render audio/video rejoin command. Removed +ildct from render audio/video rejoin command. Added -alt to render pipe. Added -alt to render audio/video rejoin command. Tried with and without the frames to fields effect in Cinelerra. and various combinations of the above. I've also tried this: change the Cinelerra fps to 50, use fields to frames (instead of frames to fields), render to an intermediate QTforlinux jpeg video stream, re-importing that back into Cinelerra, adding a frames to fields effect and then rendering that output as normal (@25fps), and I still have the same problem. Has anyone experienced this "jerking" playback before? Can anyone give any suggestions on how to fix it? (Like I say, it plays back fine on a PC, but not on any of the standalone players I've tried)

    Read the article

  • Start a software company offshore

    - by Mascarpone
    Hello Everybody, I own a small, very young, EU based (Italy) company, and among other things, we sell IT solutions. I have a degree in applied mathematics, and I mainly deal with user interfaces, embedded systems, automation and web applications. You can say that I'm an enlightened entrepreneur because I work only with open source software (OS, IDE, I release under BSD , ... everything is free as in freedom), I give high importance to post sales services and customer satisfaction, plus I think I'm the best boss someone could desire (LOL), as I have google in mind when I think about IT workers rights. But the most beautiful thing is that, although everybody advised us not to use open source, is that we are quite profitable!!! (for the sixth trimester in a row). Now I offshore most of the work to an Indian company. I divide the work in modules and I outsource the longer or more trivial ones. I spend a lot of time defining the specifications and I leave the hard work to them. Using productivity bonuses, a lot of prototypes and third-party audits I think that my software has reached a very good quality level. I would like to start my own software development company, in order to improve control over process and cut costs. Obviously I can't afford the cost of labor in the EU, so I thought about opening a company in Asia. What I need Is: 1) Cheap labor - I can afford to give productivity bonuses and higher than average wages and stay profitable just because labor is cheap. 2) Many talents - I need a good level of tertiary education, and a good number of graduates, so I can hire junior developers and train and teach them according to my needs and philosophies (e.g.: open source mind) 3) Good infrastructure - buildings, transport, internet, .... everything that a company might need. I thought about 3 possible candidates: 1) India - I already work with indian people, I know that they are realiable and speak a good english. Big cities are too expensive, but maybe a small city like lucknow http://en.wikipedia.org/wiki/Lucknow could suits my needs. 2) China - They say it's cheaper than India, but I everytime I worked with a chineese company the language was a big barrier. They work hard, are somewhat skilled and cheap but maybe it's a risky path. Plus I feel a little uncofortable with their lack of human rights. 3) Philippines - Same as china: cheaper than india, but maybe less educated. Where do you think it's the best place to start a software company? Any reading or book to advise? thank you very much

    Read the article

  • What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

    - by Adrian Hope-Bailie
    We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

    Read the article

  • Failed to start up after upgrading software in ubuntu 10.10

    - by Landy
    I've been running Ubuntu 10.10 in a physical x86-64 machine. Today Update Manager reminded me that there are some updates to install and I confirmed the action. I should had read the update list but I didn't. I can only remember there is an update about cups. After the upgrading, Update Manager requires a restart and I confirmed too. But after the restart, the computer can't start up. There are errors in the console. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. [xxx]usb 1-8: new high speed USB device using ehci_hcd and address 3 [xxx]usb 2-1: new full speed USB device using ohci_hcd and address 2 [xxx]hub 2-1:1.0: USB hub found [xxx]hub 2-1:1.0: 4 ports detected [xxx]usb 2-1.1: new low speed USB device using ohci_hcd and address 3 Gave up waiting for root device. Common probles: - Boot args (cat /proc/cmdline) - Check rootdelay=(did the system wait long enough) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory ALERT! /dev/sda1 does not exist. Dropping to a shell! BusyBox v1.15.3 (Ubuntu 1:1.15.3-1ubuntu5) built-in shell(ash) Enter 'help' for a list of built-in commands. (initramfs)[cursor is here] At the moment, I can't input anything in the console. The keyboard doesn't work at all. What's wrong? How can I check boot args or "root=" as suggested? How can I fix this issue? Thanks. =============== PS1: the /dev/sda1 is type ext4 (rw,nosuid,nodev) PS2: the /dev/sda1 can be mounted and accessed successfully under SUSE 11 SP1 x64.

    Read the article

  • Creating a network link between 2 very close buildings

    - by Daniel Johnson
    I have a charity who have two adjacent medium sized modern detached houses (in the UK): the buildings stand next to each other and are less than 5 metres apart. They have DSL connected to a single computer in one of the buildings. They want to add a network with wireless, and want it to work across both buildings. Being a charity they need to keep costs down. The network would be used for sharing Word documents, e-mail, browsing and skyping. My initial thoughts were to connect the buildings with fibre. So: Option 1 Use fibre between the buildings. Sufficient cable and two TP-LINK MC100CM Fast Ethernet Media Converters. Cost ~£80.00. But there is the extra cost and hassle of running the cable down and up the external walls, lifting and relaying paving, and burying underground. Never having fitted fibre I'm also a little worried about going up the wall and then bending the cable at 90 degrees to go through the wall and into the building. Option 2 Use two TP-Link TL-WA7510N High Powered Outdoor 5Ghz 15dBi Wireless antennas to connect the buildings. There is a clear line of sight at first floor level. Cost ~£100. And much easier to fit than fibre! Is using the TL-WA7510Ns overkill? Is there something more suitable? I had hoped to use some Netgear stuff, e.g. two DGN2200, one in each house and also use them to provide the wireless link between the buildings. However, in bridge mode wireless client association is not available and repeater mode with client association only supports WEP security which isn't strong enough. Is there something similar that would be up to the job? Option 3 Connect the buildings with UTP cable. My concerns here are risk of electric shock due to a difference of potential between the buildings (or are they so close this shouldn't be an issue) and protection from lightning strikes. Is fitting lighting arrestors expensive? And what can be done to ameliorate against the risk of shock? This all falls outside my area of expertise so I would really appreciate some advice.

    Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >