Search Results

Search found 9271 results on 371 pages for 'properties'.

Page 276/371 | < Previous Page | 272 273 274 275 276 277 278 279 280 281 282 283  | Next Page >

  • ASP.Net Session Timing Out Rapidly

    - by Zac
    We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

    Read the article

  • Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

    - by Nick G
    I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

    Read the article

  • Changing SkyDrive default location on Windows 8.1

    - by jmblack
    Update: This issue is due to the use of any non-local location for the SkyDrive folder. I've currently worked around this by using a local folder, but this has not resolved the original problem. I am trying to change the location where SkyDrive is located in Windows 8.1. This is the newly integrated SkyDrive, and not a downloadable client. There are a couple of similar questions on this site, but they pertain to Windows 8 and 8.1 Preview: Changing the SkyDrive default path in Windows 8.1 (Windows 8.1 Preview) How do I change the SkyDrive default folder in Windows (Windows 8) The SkyDrive folder is a system folder in 8.1, and like other system folders, has a Location tab in its properties that theoretically lets you change its location. I was able to do this with other system folders such as Downloads and Pictures, but there is an error when I try to change this for SkyDrive. Edit: The location that causes this error is a mapped network drive. The error does not occur when trying to move SkyDrive to another location on the same drive. There are no permission restrictions on the mapped network drive. Edit #2: This is the method I followed that produced the error: A screenshot of the error can be found here Has anyone else encountered this or have any information on this?

    Read the article

  • Windows Server 2012 licensing issue preventing RDP connections?

    - by QF_Developer
    I am witnessing an unusual behaviour on 1 of 5 Windows Server 2012 R2 machines (clean install) that is preventing any remote connections from being established via RDP. I have run through the prerequisites for RDP here but I am finding that any remote connection attempt instantly stops the "Windows Protection Service". When I check the event logs I see the following entry. The Software Protection Service has stopped Event ID: 903 Source: Security-SPP From what I have read Security-SPP is tasked with enforcing activation and licensing, it appears that RDP requires this service to be in the running state. Is it possible that I have inadvertently activated this instance of Windows with a key that has already been associated to another instance (We have 5 keys as part of an MSDN subscription)? Would this be sufficient to block RDP access? When I look under System Properties (Windows Activation) it states that Windows is activated and there are no other obvious indicators that there's a licensing issue. EDIT 1: I ran a Powershell script to display the product keys for all servers in order to check for any duplication. For the problematic server I am getting the message The RPC server is unavailable.

    Read the article

  • windows xp cannot access admin share

    - by barlop
    I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

    Read the article

  • How to always show titles on Windows 7 Taskbar thumbail preview?

    - by Cooper
    I often use the Win+n shortcuts to 'alt-tab' between windows of pinned application (i.e. Win+2 to basically 'alt-tab' multiple putty windows, where putty is pinned as app #2 on the taskbar). The Win+n always pops up the thumbnail previews of all the windows, but sometimes it shows window titles above the thumbnail, sometimes it doesn't. Is there any way to always show the titles (i.e. registry setting?)? For putty sessions this would be especially nice, as the title contains the hostname, and the thumbnail is too small to determine what host that window is for. I've noticed that the titles usually show up with there are more than ~4-6 windows of that pinned item open - but the number seems to vary - is there a threshold setting for this? Update: So I just noticed the titles show up whenever the taskbar buttons combine, which varies based on how many windows from other apps are open... So I'm now looking for a way to combine buttons (but I'd like to keep labels, so the options in the 'Taskbar and Start Menu Properties' are close, but probably finding the registry settings behind should do it.

    Read the article

  • How do i play nicely with MS SQL/SQL Server 2008

    - by acidzombie24
    Big problem. I have nearly given up. I am trying to port my prototype to use MS SQL so it will work on a server once i get it (the server will be SQL Server 2008, shared, i dont know any more info). So i tried to connect to SQL Server via visual studios IDE and had no luck. I enabled TCP and named pipes and restarted the service (and computer) with still no luck. I remembered about mdf files so i made that after an obstacle of not being able to make the connect string require i figure out visual studio has it in its properties and successfully connected with that. Then i had a problem with nested transactions. After not being able to figure out how to check i wondered if i can configure it to allow it somehow. I always thought all of MS were the same except for limitations but sql server seems to support nested transactions so theres no point trying to work around the problem with .mdf files since i wont need them and really just used it to port the base of my sql code and to check if syntax is correct. I tried installing SQL Server Management Studio since people mentioned it several times (as a solution or at least help). When installing it on windows 7 it says it may not be compatible. After running it, it launched SQL Server Installation Center (64-bit) which doesnt seem to be the same thing as i dont see a way to modify any of my server (networking) configurations or edit user permissions, etc. I am clueless what to do next. Does anyone have any ideas? I'm posting here bc i think my problem is more configurations and sql server then programming.

    Read the article

  • KVM virtual machine unable to access internet

    - by peachykeen
    I have KVM set up to run a virtual machine (Windows Home Server 2011 acting as a build agent) on a dedicated server (CentOS 6.3). Recently, I ran updates on the host, and the virtual machine is now unable to connect to the internet. The virtual network is running through NAT, the host has an interface (eth0:0) set up with a static IP (virt-manager shows the network and its IP correctly), and all connections to that IP should be sent to the guest. The host and guest can ping one another, but the guest cannot ping anything above the host, nor can I ping the guest from anywhere else (I can ping the host). Results from the guest to another server under my control and from an external system to the guest both return "Destination port unreachable". Running tcpdump on the host and destination shows the host replying to the ping, but the destination never sees it (it doesn't even look like the host is bothering to send it on at all, which leads me to suspect iptables). The ping output matches that, listing replies from 192.168.100.1. The guest can resolve DNS, however, which I find rather odd. The guest's network settings (connection TCP/IPv4 properties) are set up with a static local IP (192.168.100.128), mask of 255.255.255.0, and gateway and DNS at 192.168.100.1. When originally setting up the vm/net, I had set up some iptables rules to enable bridging, but after my hosting company complained about the bridge, I set up a new virtual net using NAT and believe I removed all the rules. The VM's network was working perfectly fine for the last few months, until yesterday. I haven't heard anything from the hosting company, didn't change anything on the guest, so as far as I know, nothing else has changed (unfortunately the list of packages updated has since fallen off scrollback and I didn't note it down).

    Read the article

  • Persistent PuTTY sessions for multiple windows

    - by Tgr
    I'm working in various Linux environments through PuTTY connections which break from time to time. I'm looking for a solution to make the PuTTY windows persist (e.g. if I was editing a file, then after reconnecting I should be in the same editor with the same file open at the same place), with the following requirements: it shouldn't require any manual setup at the beginning of the session or after reconnection (I don't want to type in screen or anything like that) I have several windows open to the same machine with the same user, which tend to disconnect at the same time the number/role of windows is not constant (it's not like I have an mc window, a mysql window and a "script runner" window; sometimes I use one window for search or for SVN commands, other times I need several at the same time) sometimes I need to change the properties of the windows for a task (large window for grepping/editing, small windows because I need to see two of them at the same time, red background because I am modifying the live database in MySQL etc), so I need to get the same console back in the same window after a reconnect Is there a way to achieve this? I suppose I should use screen or something equivalent, but how does it know which window I am reconnecting from? Is there some way to pass a unique window identifier to the shell from PuTTY?

    Read the article

  • The BitLocker encrypted logical drive of my laptop is not accessible. On clicking error appears,"Application not found"

    - by Nauman Khan
    I had an important personal data that was stored in my laptop drive 'F'. My 4 year old son also uses my laptop to play games. To secure my data I used bitlocker software that was already there in my windows 7 ultimate 32 bit. I am using a Dell D 630 Core2Duo laptop. The thing worked fine for me and I have been able to access my data in drive 'F' as and when I required. But today, when I tried to open my 'F' drive, an error box appeared saying "Application not found". I right clicked and checked 'properties' of 'F' drive. It showed me Used Space = 0 bytes and Free Space = 0 bytes. I opened 'Disk Management' which showed my 'F' drive file system as 'Unknown (Bitlocker Encrypted). 'Disk Management' is also showing my 'F' drive as healthy logical drive. I opened 'Manage bitlocker' and found that my 'F' drive was being shown locked and 'Unlock Drive' was displayed against it, however, when i click on 'Unlock Drive', it does not function. I opened 'TPM Administration' and found an information that 'Compatible TPM cannot be found'. My bitlocker encryption was working fine which means that I had a compatible TPM in my laptop. Where has it gone? How can I enable it? Is my 'F' Drive lost forever and thus the data in there as well?

    Read the article

  • What user information is exposed via a browser?

    - by ipso
    Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

    Read the article

  • SBS 2008 - DNS Forwarders timing out.

    - by Moif Murphy
    Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

    Read the article

  • Per-mailbox IMAP settings in Exchange 2003 apply successfully but revert to server default

    - by erictheavg
    The title says most of it. I have a Spiceworks mailbox that connects to our Exchange Server 2003 box via IMAP for receiving help desk issues. But for complicated reasons, I want it to receive those emails in text-only format. So, I discovered that you can just go to: Exchange System Manager Administrative Groups First Administrative Group First Storage Group Mailbox Store Mailboxes Right-click the mailbox, Configure Exchange Features Edit the properties for IMAP Set that mailbox to only receive message bodies as plain text. I click OK, then Next, it reports success, and I assume I'm done. But then when I go right back to where I was, I see that "Use protocol defaults" is still checked. Anyone have a clue why this would be? Some other details: I'm logged in as Administrator when I do this. I can't change this setting for the entire IMAP virtual server because some regular users use it. I only have one IP address to play with, which means I can't create another IMAP virtual server. Any suggestions or ideas are greatly appreciated!

    Read the article

  • Frequency of RAM

    - by Vignesh Palani
    I have a very old system hp compaq dx2080. It had 1gb of RAM. I recently bought a EVM DDR2 1 GB PC RAM which had a clock rate of 667Mhz. I have dual booting windows 7 and 8. When I installed it, windows 7 was still using the older 1gb. It showed as 2 gb available and 1gb usable in system properties. I searched around and found that I can change it to max in the msconfig. I did so. I set it 2048. Still, it was using only 1gb. When, I switched to 8, it was using the 2gb. Now, for my question: My system only supported 553Mhz and 667Mhz RAM. In the BIOS, I saw that the new RAM was showing as 800Mhz. Rechecked using speccy and cpu-z. It showed different values between the two. The RAM is labeled as 667Mhz over it. No mistake in that. But, am I missing something? Please help. And, can I continue using it? My point again. There are only two slots.

    Read the article

  • Scripted redirection for Outlook 2003

    - by John Gardeniers
    We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

    Read the article

  • How to script GPO in Windows computers without Active Directory?

    - by Peteris Krumins
    Does anyone know how to script GPO for users in a Windows computer that is not on any Active Directory network? I can't use GPMC because it doesn't work without a domain. I have been searching the net for the last couple of hours and all the solutions that I find are related to GPMC. I'd imagine there are some objects in the GPO that are accessible via WMI? Does anyone know anything about that? I was unable to find any information about that. Here is the situation I am trying to script: I have 10 users on the machine, and I want to restrict what they are able to do on the machine. So I created 10 GPOs for each one of them. Now I want to apply a common policy to all of them. The only way to do it is to go through each of the GPO and do it manually. This is too time consuming, therefore I am seeking for a simpler solution. I was unable to find a way to copy GPO from a user to a user. That would make it much easier, I would create a GPO for 1st user, then copy it over to all the other users, but no luck, couldn't find a way to copy GPOs. The other method I tried was creating a GPO for the whole user group but it turns out you can't apply GPO to a group unless you use GPMC, which I can't cause the computer is not on any domain. So I am thinking about scripting this whole process, but again I can't find any examples of how to access particular GPO objects for particular users and modify properties through WMI. Any suggestions on the issue I am having? Thanks!

    Read the article

  • How to perform this Windows 7 permissions change on many files via GUI or command line

    - by hippietrail
    After using my external hard drive on another Windows 7 computer to tweak photos with Windows Live Photo Gallery then upload them to Facebook I found the modified images were now not visible on the original Windows 7 computer. I'm not sure if the things I tried to get it working subsequently changed anything, but I do know this is the sequence of actions that makes the permissions of the modified files match those of the unmodified files: Right click on broken image file, select "Properties" On the "Security" tab press the "Advanced" button In the "Permissions" tab press the "Continue" button with the shield icon on it Tick the box marked "Include inheritable permissions from this object's parent Click the "Remove" button to remove the only current entry "Type: Allow, Name: Administrators (XYZ\Administrators), Permission: Full control, Inherited From: OK on the "Permissions" tab. OK on the "Security" tab. Now this same procedure does not work at the folder level. It results in "access denied" dialogs. I'm looking for some way to perform this exact modification on all the images I edited on the other computer. I'm happy to use the Windows GUI in Explorer or any other included tools. I'm happy to use the Windows command line. I'd prefer not to use a third-party tool since I'd have to be satisfied it's not doing anything else. I'm not looking for a different way to change permissions to other settings to make an external drive full of photos editable on multiple computers. At least not in this question.

    Read the article

  • (Windows 7) Shared External Drive Permission Issues

    - by connec
    So, say I share my system (C) drive through windows (E.g. properties -> Sharing -> Advanced Sharing -> Share this Folder). I can then access this drive at \\Comp\C on another networked computer - all is well. However, if I insert a removable (USB) disk, say "E", and proceed to share it the same way, when I attempt to access \\Comp\E (either directly or through browsing) I get an error: Windows cannot access \\Comp\E You do not have permission to access \\Comp\E. Contact your network administrator to request access. Now, the permissions (Advanced Sharing -> Permissions) are set with "Everyone" having read access (same as the internal drive), so this doesn't make a lot of sense. Also of note, I have an SSH server on my computer (through Cygwin) and even through SSH (logging in as an administrator user) I cannot access /cygdrive/e (although /cygdrive/c is accessible). As a final note, the drive is of course accessible on the host machine (E:\), and also at \\Comp\E on the host machine.

    Read the article

  • windows xp cannot access admin share

    - by barlop
    I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

    Read the article

  • SQL Server 2008 services error on account

    - by TheDude
    I installed SQL Server Enterprise, but can't get it to work. It is a stand alone, on a laptop for development purposes. No network is involved, no other users. The OS is windows 7. Now, I keep receiving eventId 7000, which means that access is denied for the user (the user was Network Services). So, after reading up on it, I kind of got the idea that a user account should be created with minimal privileges. So, off I went and added a user, SQLservices. In the SQL Server Configuration Manager I right clicked SQL Server(MSSQLSERVER), and in the properties I added my new user. Well, here's mister eventId 7000 again. I don't get what I am doing wrong. Also, this new user ends up on my start-up screen. I don't think I want that... I mean, it would be weird to have x number of users crowding up my start-up screen just because I created those for my windows services... The error I get when I add the user in SQL Server Configuration Manager is as follows: Permission Denied. [0x80070005] Helps!

    Read the article

  • Disable Windows 7 taskbar grouping. Not combining.

    - by Byran
    I've look near and far but I cannot find a way (setting or hack) to prevent Windows 7 from grouping taskbar buttons together that are "related". I'm not talking about the option to combine or collapse related buttons into one item. I can find that setting at: Taskbar and Start Menu Properties Taskbar Taskbar buttons: This is what I an not looking for: How to Enable or Disable Windows 7 Taskbar Button Grouping I'm talking about how Windows 7 seams to think that it's doing me a favor by grouping all my Google Chrome buttons together and grouping all my Explorer buttons together etc. My workflow in Windows XP was to use the program Taskbar Shuffle to allow me to reorganize my taskbar buttons into related task "groups" I was working on. For example: [Start Button] | [iTunes] [Outlook Express] [Chrome Gmail] [layered design folder] [Photoshop CS4] [exported images folder] [website root folder] [Dreamweaver CS4] [Chrome www.MyAwesomeWebsiteImBuilding.com] [Chrome Recent web search] [some unrelated folder] Windows 7 doesn't seem to let me do this. It wants to do: [Start Button] | [layered design folder][exported images folder][website root folder][some unrelated folder] | [Chrome www.MyAwesomeWebsiteImBuilding.com]Chrome [Gmail][Chrome Recent web search] | [iTunes] | [Outlook Express] | [Photoshop CS4] | [Dreamweaver CS4] Does anyone know of a tool or hack to prevent Windows 7 from grouping taskbar buttons?

    Read the article

  • Problems setting up VLC Sever/client streaming

    - by Ayos
    I'm trying to set up a Linux machine as the server and a Windows XP machine as the client. Both machines are connected to the same local network via a Wi-Fi router. I setup the stream with the following properties : http stream port 8080 play locally And not much else. No firewall on the windows client(Windows firewall is disabled) When I try to open network stream via the client machine(Using VLC or Windows Media Player) I get the following errors: Media Player error code : 0xC00D11B3: Encountered a network Problem. VLC Console: main warning: connection timed out access_mms error: cannot connect to 192.168.1.3:8080 main debug: no access module matching "http" could be loaded main debug: TIMER module_need() : 12625.810 ms - Total 12625.810 ms / 1 intvls (Avg 12625.809 ms) main error: open of `http://192.168.1.3:8080' failed main debug: dead input main debug: repeating item main debug: starting playback of the new playlist item main debug: resyncing on http://192.168.1.3:8080 main debug: http://192.168.1.3:8080 is at 0 main debug: creating new input thread main debug: Creating an input for 'http://192.168.1.3:8080' main debug: using timeshift granularity of 50 MiB, in path 'C:\DOCUME~1\Accer\LOCALS~1\Temp' main debug: `http://192.168.1.3:8080' gives access `http' demux `' path `192.168.1.3:8080' main debug: creating demux: access='http' demux='' location='192.168.1.3:8080' file='\\192.168.1.3:8080' main debug: looking for access_demux module: 0 candidates main debug: no access_demux module matched "http" main debug: TIMER module_need() : 0.461 ms - Total 0.461 ms / 1 intvls (Avg 0.461 ms) main debug: creating access 'http' location='192.168.1.3:8080', path='\\192.168.1.3:8080' main debug: looking for access module: 2 candidates access_http debug: http: server='192.168.1.3' port=8080 file='' main debug: net: connecting to 192.168.1.3 port 8080 qt4 debug: IM: Deleting the input main debug: TIMER input launching for 'http://192.168.1.3:8080' : 13397.979 ms - Total 13397.979 ms / 1 intvls (Avg 13397.978 ms) qt4 debug: IM: Setting an input Need Help. Thanks in advance.

    Read the article

  • Windows 7 explorer crashing trying to read external hard disk

    - by Mario De Schaepmeester
    I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

    Read the article

  • Copied a file with winscp; only winscp can see it

    - by nilbus
    I recently copied a 25.5GB file from another machine using WinSCP. I copied it to C:\beth.tar.gz, and WinSCP can still see the file. However no other app (including Explorer) can see the file. What might cause this, and how can I fix it? The details that might or might not matter WinSCP shows the size of the file (C:\beth.tar.gz) correctly as 27,460,124,080 bytes, which matches the filesize on the remote host Neither explorer, cmd (command line prompt w/ dir C:\), the 7Zip archive program, nor any other File Open dialog can see the beth.tar.gz file under C:\ I have configured Explorer to show hidden files I can move the file to other directories using WinSCP If I try to move the file to Users/, UAC prompts me for administrative rights, which I grant, and I get this error: Could not find this item The item is no longer located in C:\ When I try to transfer the file back to the remote host in a new directory, the transfer starts successfully and transfers data The transfer had about 30 minutes remaining when I left it for the night The morning after the file transfer, I was greeted with a message saying that the connection to the server had been lost. I don't think this is relevant, since I did not tell it to disconnect after the file was done transferring, and it likely disconnected after the file transfer finished. I'm using an old version of WinSCP - v4.1.8 from 2008 I can view the file properties in WinSCP: Type of file: 7zip (.gz) Location: C:\ Attributes: none (Ready-only, Hidden, Archive, or Ready for indexing) Security: SYSTEM, my user, and Administrators group have full permissions - everything other than "special permissions" is checked under Allow for all 3 users/groups (my user, Administrators, SYSTEM) What's going on?!

    Read the article

  • Anyone have a script to delete a specific local windows profile?

    - by Jordan Weinstein
    I'm looking for Powershell (preferred) script, or .CMD or .VBS, to delete a specific user profile on a workstation (WinXP) or terminal server (2000, '03 or '08). I know all about the delprof utility... That only allows you delete based on a period of inactivity. I want a script to: prompt admin for a username delete that username's profile and to delete the entire profile - registry hive too (not just the folder structure within Documents and Settings). The same way it would if you went to My Computer Properties Advanced tab User Profiles Settings and deleted profiles from there. Any ideas? All I can think of is doing an AD lookup to get the SID of the user specified, then using that to delete the correct registry hive too... something simpler would be nice though... Basically, my HelpDesk used to be local administrators on our Citrix servers and a common fix for various issues was for them to delete a user's profile on the citrix server(s) and have that user log back in - voila, whatever issue they had was resolved. Going forward, in new Citrix environment, they will no longer be local admins on those boxes, but still need to be able to delete profiles (deleting the entire profile: folder and reg hive is key). thanks.

    Read the article

< Previous Page | 272 273 274 275 276 277 278 279 280 281 282 283  | Next Page >