Search Results

Search found 11767 results on 471 pages for 'org'.

Page 277/471 | < Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >

  • Routing traffic to specific web sites through Ethernet, rest via wifi on Mac OS X 10.6?

    - by user32448
    Hi I have two separate Internet connections connected to a Mac and I'd like one of them (via Ethernet eth0 gateway 192.168.2.1) to serve for just backing up to an remote online storage, and the other one (via Airport en1 gateway 192.168.1.1) for all other Internet traffic. I tried using "route" from the terminal as follows: sudo route add -host 98.207.226.113 -interface eth0 (just for testing against the site www.whatismyip.org whose IP is 98.207.226.113, to see through which gateway the traffic is routed) I can see using netstat that the route is added: $ netstat -rn -f inet Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 49 0 en1 98.207.226.113 192.168.2.1 UGSc 0 0 eth0 However, the traffic in this case does NOT get routed properly through Ethernet, as if the routing definition I made is ignored. Any ideas? Thanks!

    Read the article

  • apache php access rights configuration

    - by AndreasT
    Hi, I am a complete apache and co newb. Currently it serves only the default page. On the default page, the user can not list the directory or files. When I create a directory, say /var/www/foobar and place files in it, the user can by doing: www.mydomain.org/foobar see the contents of the directory. I run pretty much the default configuration. on Directory "/", I have FollowSymlinks and AllowOverride(none) on what DocumentRoot points to I have Indexes FollowSymlinks MultiViews and "allow from all" set. My questions are: Can I stop people from listing subdirectories? Can people, if I do not change the configuration, in some way read the php files in there? (I mean not the rendered page, I mean the .php page source.) Pointers to good resources about this would also be nice. Thx in Advance.

    Read the article

  • Gentoo Linux -> Ubuntu: Can I Preserve My LVM/RAID Devices, Or Do I Need To Reformat?

    - by Eddie Parker
    Hello: I've got a Gentoo box that I'm interested in switching over to an Ubuntu box. I currently have the partitions laid out using a mixture of RAID (mdadm) and LVM2, as specified in this document [1]. Ideally I'd like to just wipe out the non /home partition, as it's got data I'd like to keep. Is it possible to reuse the current setup, or do I need to restart? vgdisplay, vgchange -a y, etc don't yield any results from the Ubuntu LiveCD, and I'm wary to run any commands that might wipe my data. Your help would be appreciated. [1] http://www.gentoo.org/doc/en/gentoo-x86+raid+lvm2-quickinstall.xml

    Read the article

  • Can a 32-bit RHEL4 userland work with a 64-bit kernel?

    - by James
    Is there a way to change an i386 RHEL4 machine to run an amd64 kernel, but ensure that it still builds software into same i386 binaries? On Debian this seems quite straightforward: just install an amd64 kernel (worst case, build one like this guy: http://www.debian-administration.org/users/jonesy/weblog/1) and prefix everything with "linux32". Then everything that considers uname -m will be unchanged, I just need to handle the few cases that consider uname -r. What is the Red Hat equivalent? Is the only way a full 64-bit installation on another disk and then chrooting back to the 32-bit system before anyone builds anything? (Even the best examples of that seem to be Debian-based.) Background: We make a large system that runs on (a variant of) i386 RHEL4. However, some of the larger RHEL build machines now have enough RAM that they might benefit from going 64-bit (for the kernel and maybe some of the bigger build steps). Our build system doesn't support cross-compilation.

    Read the article

  • Use cURL with multiple POSTs

    - by Austin
    I'm trying to use cURL to download the contents of webpages that require forms to get to. In a browser it looks something like this 1.) Login using POST 2.) Pick which page to go to using another POST 3.) Pick another page... using POST 4.) etc.. until I get to the page I want, then download all textfiles linked to on that page. I am attempting to do this using a bash script and some loops with the values that change for each POST. My problem is how do I do multiple POSTs with cURL? Must there be cookies involved? FYI the website is http://metagenomics.nmpdr.org/ (MG-RAST).

    Read the article

  • Ubuntu 12.04 Server: permissions on /var/www for newly copied files

    - by Abe
    I ran the following commands to set up ACL on the /var/www folder in my Ubuntu 12.04 Server: sudo usermod -g www-data abe sudo chown -R www-data:www-data /var/www sudo chmod -R 775 /var/www I downloaded Wordpress using wget in my /var/www folder and unzipped the downloaded file: cd /var/www wget http://wordpress.org/latest.zip mv latest.zip wordpress.zip unzip wordpress.zip I created a new database and user in mysql and attempted to run the setup process through the web interface. When I enter the configuration info in wordpress I run into the following error message: Sorry, but I can't write the wp-config.php file. When I run ls -la, I see that the files are owned by my user abe, but they are part of the group www-data. Would I have to run the chmod command every time I copy new files to /var/www? sudo chmod -R 775 /var/www

    Read the article

  • Source of Unexplained Requests in Server Logs

    - by Synetech inc.
    Hi, I am baffled by some entries in my server logs, specifically the web-server logs. Other than normal, expected traffic, I have noticed three types of request errors (eg 404, etc.): Broken links, ie links from old, external pages that point to pages that are no longer here Sequences of probes, ie some jerk trying to hack in by scanning my server for a series of exploitable admin type pages and such What appear to be completely random requests for things that have never existed on the server or even have anything to do with the server, and appear by themselves (ie not a series of requests like the probes) Could it somehow be a mistyped URL or IP? That’s about the only thing that I can think of, but still, how could I get a request on say, foobar.dyndns.org (12.34.56.78) for something like www.wantsfly.com/prx2.php or /MNG/LIVE or http://ant.dsabuse.com/abc.php?auth=45V456b09m&strPassword=X%5BMTR__CBZ%40VA&nLoginId=43. (Those are a few actual requests from my logs.) Can someone please explain scenario three to me? Thanks.

    Read the article

  • Windows 8 mail cause event 529 when connect to exchange

    - by holian
    I set my company exchange mailbox in Windows 8.1 mail. (outsite). Everything works fine, but after i start the Windows 8.1 mail i get event with id 529 in the security log continously. Reason: Unknown user name or bad password Username: [email protected] range: Type of login: 8 Logon Process: Advapi Authentication Package: Negotiate Workstation Name: SERVERNAME Caller User Name: SERVERNAME $ Calling range BAR NUL Caller Logon ID: (0x0, 0x3E7) Caller Process ID: 4384 Transmitted services: - Source Network Address: 56.43.213.122 Source Port: 55 698 If i close windows mail, events stop flooding the security log in the server. Connection parameters in windwos 8: email:[email protected] password domain:company.local username:myemail server:mydomain.dyndns.org SSL:yes. Any idea whats the problem? I can check my mail, with the same setting on my android phone without any problem. Thank you

    Read the article

  • nagios: trouble using check_smtps command

    - by ethrbunny
    I'm trying to use this command to check on port 587 for my postfix server. Using nmap -P0 mail.server.com I see this: Starting Nmap 5.51 ( http://nmap.org ) at 2013-11-04 05:01 PST Nmap scan report for mail.server.com (xx.xx.xx.xx) Host is up (0.0016s latency). rDNS record for xx.xx.xx.xx: another.server.com Not shown: 990 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 110/tcp open pop3 111/tcp open rpcbind 143/tcp open imap 465/tcp open smtps 587/tcp open submission 993/tcp open imaps 995/tcp open pop3s 5666/tcp open nrpe So I know the relevant ports for smtps (465 or 587) are open. When I use openssl s_client -connect mail.server.com:587 -starttls smtp I get a connection with all the various SSL info. (Same for port 465). But when I try libexec/check_ssmtp -H mail.server.com -p587 I get: CRITICAL - Cannot make SSL connection. 140200102082408:error:140770FC:SSL routines:SSL23_GET_SERVER_HELLO:unknown protocol:s23_clnt.c:699: What am I doing wrong?

    Read the article

  • Any worker agent monitors for appliance based load balancers?

    - by Zethris
    Looking to find out to what extent an appliance load balancer can monitor servers for both failover (say for example a service like apache tomcat fails) and load balancing? Right now it looks like it's just port monitoring/connection tracking and healthcheck urls that it will heartbeat and detect as down if it doesn't come back with a finished request. We are looking at the Kemp 3500 or Loadbalancer.org solutions. Is there any sort of web application level monitoring/load balancing that these load balancers can offer that can more directly interact with the servers it's balancing?

    Read the article

  • Problems installing icinga-web

    - by Kungurov
    I'm using Ubuntu 10.04 LTS (64bit, Server), Apache 2.2.14 Following the instruction from the oficial icinga page http://docs.icinga.org/latest/en/index.html I installed the icinga-web-1.7.1 on my machine and configured a few hosts for test purposes. The Classic Interface runs as expected but the new Web Interface does not show any data. When I try: ps aux | grep ido2db | grep -v grep I get: icinga 27425 0.0 0.0 41464 600 ? Ss Jul27 0:00 /usr/local/icinga/bin/ido2db -c /usr/local/icinga/etc/ido2db.cfg which might indicate a problem with idomod/ido2db because according to the docs there should be at least 2 processes greped. Any ideas how to fix that?

    Read the article

  • memcached install issues with lib event on server

    - by albert N
    I've installed libevent on my server in the directory root/data/ and have i'm about to install memcached with ./configure –with-lib-event=/data/; make; make install However, after running a bit I get this error saying i'm pointing to the wrong directory for libevent. checking for libevent directory... configure: error: libevent is required. You can get it from http://www.monkey.org/~provos/libevent/ If it's already installed, specify its path using --with-libevent=/dir/ make: *** No targets specified and no makefile found. Stop. make: *** No rule to make target `install'. Stop. Any suggestions. I am not experience with cli so anything is help. Thanks!

    Read the article

  • Puppet claims to be unable to resolve domains even if domain properly resolves

    - by gparent
    I have a fairly simple puppet setup, one master and one node, both running Debian Squeeze 6.0.4. I have DNS entries for the two machines, client and master respectively. Both client and master's DNS entries resolve correctly on both machines to the right IPs. On my client, I have this configuration: [main] server = master.example.org logdir=/var/log/puppet vardir=/var/lib/puppet ssldir=/var/lib/puppet/ssl rundir=/var/run/puppet factpath=$vardir/lib/facter pluginsync=true templatedir=/var/lib/puppet/templates Key exchange seems to fail, according to this messages in /var/log/syslog: localhost puppet-agent[11364]: Could not request certificate: getaddrinfo: Name or service not known Why is resolution not working only for puppet?

    Read the article

  • .htaccess folder rewrite

    - by Lisa
    I have 3 URLS all pointing to the same site. www.abc.co.uk www.xyz.com www.123abc.org I have a folder /foo/bar which has lots of sub folders and files in etc. I want to rewrite this to /bar. So if I have www.abc.co.uk/foo/bar/sheep/page.html I want it to redirect to www.abc.co.uk/bar/sheep/page.html. Is this possible. Sometime I may have a URL like www.abc.co.uk/foo/bar/foo/page.html so this would become www.abc.co.uk/bar/foo/page.html. Only the first instance of foo would be rewritten.

    Read the article

  • Repositories for CentOS that don't suck?

    - by Keyo
    I'm used to using ubuntu/debian repositories and they are great. I can apt-get just about any package and it'll be there. I have not found this on centos. I called my hosting company and they suggest I install atomic turtle since it's compatible with cPanel. This didn't work when I tried to install git. yum install git ... No package git available Repeat the same thing for just about any package, the default repositories are pathetic. So perhaps there are other repositories I can use. Can anyone suggest any? Edit The problem was cPanel excluding some git dependencies in yum.conf. See http://www.cmdln.org/2010/05/07/install-git-on-centos-cpanel-server/

    Read the article

  • Weird problem, special characters after formatting the hard drive, computer not starting 0_o

    - by m3taspl0it
    Hya friends , Last night my computer was working fine. But today when i came back from college and started it , it was starting fine but after sometime it's getting restarted , again and again getting restarted at different points , so i tried to boot it in safe mode but same problem. Now after all this , i finally decided to format the drive C (it is in 80 GB) and load new OS windows XP3. After formatting and loading xp3 sufficient files , when it was getting rebooted for copying the actual os files , it hung and a weird screen came. I've also attached the pic of error : http://www.postimage.org/image.php?v=gxz1vKS My specs : P4 3.0 Ghz 2 GB RAM (2x 512 mb and 1 GB) 3 hard drives { 80 GB (5 years old around) 320 GB ( 2 years old around) 500 GB ( recently bought) 256 MB graphics card any help is very appreciated , thanks

    Read the article

  • Browser pollution / Pop Up request

    - by PatrickS
    From time to time, when I browse the internet , after entering a site's URL , I get a warning message that a pop up has been blocked , then a question mark and a set of numbers appends itself after the URL. It doesn't matter what site I want to navigate to, it can be a site I have developed, a well know site like drupal.org for instance. Here's what happens: enter url: example.com warning: pop up blocked url change to: example.com/?1347628900 After checking the pop up ( which of course turns out to be an unwanted ad ), i deducted that the request and the pop up were linked. This has never happened to me before, I'm not sure how this got started, how can I get rid of this? Clearing the cache , cookies etc... doesn't solve the issue. I'm using a Macbook Pro OS10.6.7 , Chrome 13.0.782.24 beta. Thanks in advance for any tips!

    Read the article

  • CLI-Based monitoring tool for KVM

    - by Pinnacle
    I am developing a scheduler for running VMs on KVM. The scheduling has over-commitment of resources like memory and CPU. For this, I need a CLI-based monitoring tool that keeps me giving information about the resource usage of each VM, because it might be the case that due to over-provisioning of resources, VMs on a particular host are running very slowly depending on the benchmarks/programs each VM is running, and then I need to migrate a VM to another host and so on. I looked into libvirt-based tools like collects, MUNIN, Nagios-vert, etc.( http://libvirt.org/apps.html#monitoring ) I also looked into Ubuntu utility perf-kvm ( http://manpages.ubuntu.com/manpages/maverick/man1/perf-kvm.1.html ) I want to ask which CLI-based would be recommended by the community so that I can make a automated scheduler that takes care of the above situation.

    Read the article

  • rails didnt install correclty, specificly the uninstaller

    - by sam
    ive just installed rails using railsinstaller.org for osx, rails and ruby seem to be working ok (checked by running rails -v and ruby --version). But when it installed i got an error saying that not there were errors and the uninstaller didnt install correctly. Somthing odd i saw was that when i load terminal i get this showing up Last login: Fri Nov 30 13:12:09 on ttys000 unknown5c969d7cc475:~ Sam$ specificly the "unknon5c96..." part im not sure if its related ? I think i might have got the install error as xcode wasnt installed first, for peice of mind id like to unistall it and load it back on, but when i try and run the installer from the application folder it just asks for my password and then dose nothing.. any ideas how i can fix this ?

    Read the article

  • How do I redirect/rewrite to the FQDN URL without setting ServerName?

    - by ChaimKut
    Often in intranets, users will direct URLs to a hostname without supplying the FQDN. Example: http://internalHost Instead of http://internalHost.example.com I would like to redirect users / rewrite URLs so that everything will use the FQDN. Here's the catch: I don't want to set ServerName explicitly. (This is for a product which will be deployed in multiple intranets so we can't know the value of ServerName ahead of time). According to: http://wiki.apache.org/httpd/CouldNotDetermineServerName Apache uses a reverse lookup to determine a default FQDN. How can I make use of/reference that FQDN that Apache is using for a mod_rewrite or redirect?

    Read the article

  • How do i enable deflate on apache2? debian

    - by acidzombie24
    I looked at the other answers and those solutions did not help. I am completely confused how to do this. I know almost nothing about apache nor how to use it and nearly all the article say write this but doesnt tell me where. So far i have done this # a2enmod deflate Module deflate already enabled Then i tried writing this in httpd.conf AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css Then i wrote a longer version which involved deflate.c. After those didnt work i deleted them all and wrote the AddOutputFilterByType line in apache2/sites-enabled/000-default inside of I used this to test http://www.whatsmyip.org/http_compression/ everytime it says no compression. I used another site but i could never compress. Also i restart the server everytime i save a file so what could be the problem and how do i enable this properly?

    Read the article

  • Installing maven on Ubuntu by manual download

    - by WebDevHobo
    To install Maven, I downloaded the latest version from the website and then followed these steps: http://maven.apache.org/download.html#Installation The last step, the version control, does not work. It says that 'mvn' is currently not installed and that I should type sudo apt-get install maven2 If I go directly to the mvn file itself, it does work: root@ubuntu:~# /usr/local/apache-maven/apache-maven-2.2.1/bin/mvn --version Apache Maven 2.2.1 (r801777; 2009-08-06 12:16:01-0700) Java version: 1.6.0_21 Java home: /usr/java/jdk1.6.0_21/jre Default locale: en_US, platform encoding: UTF-8 OS name: "linux" version: "2.6.32-25-generic" arch: "i386" Family: "unix" So, what am I doing wrong here? Or what would and apt-get install do extra that I might have forgotten?

    Read the article

  • Choosing a home network layout

    - by James M.
    I have a server, 4 PC's, a network printer, a switch and an ADSL modem. Currently the server runs Red Hat 9 and sits between the internet and the other PCs like in http://upload.wikimedia.org/wikipedia/en/1/12/Sample-network-diagram.png I have bought a new server PC to replace the old one, and I plan to install Fedora Core linux on it. The server acts as web and file server. The PCs all run Windows. Alternatively, I could connect the new server and all PCs to the switch, and connect the switch to the modem. (Sorry, couldn't find an image.) What are the pros and cons of these network layouts? Eg. in terms of reliability, security and flexibility? I am not a Linux guru but know of (and am not afraid of) iptables, dhcpd et al. Thank you for any tips, pointers and links.

    Read the article

  • SPF record doesn't work (not sure which DNS server to tweak)

    - by Ion
    Problem: Google (and perhaps others) marks our emails as SPF neutral. Let me give you some background about the setup: initially got a dedicated server (Hetzner) with Plesk installed to host a domain/web application, let's say: bigjaws.com. Plesk automatically creates a DNS zone for it with some records for the various services it provides out of the box, e.g. webmail.bigjaws.com as a CNAME to bigjaws.com to provide Horde/whatever, etc. Let me point out four relevant of these records (where XXX.XXX.XXX.158 is our dedicated IP): bigjaws.com. A XXX.XXX.XXX.158 mail.bigjaws.com. A XXX.XXX.XXX.158 bigjaws.com MX (10) mail.bigjaws.com. bigjaws.com. TXT v=spf1 +a +mx -all The above records are not(?) valid anymore though, because after using this dedicated server for a while, our site got bigger and bigger so we decided to move our operations over to AWS (EC2, RDS, ELB, etc), but we retained the mail functionality as is, i.e. emails from [email protected] are sent by connecting to our dedicated server where Plesk takes care of things. This was decided in order not to setup anything from scratch. Of course for all DNS-related things we now use Route53. In Route53 I have the following records: mail.schoox.com. A XXX.XXX.XXX.158 bigjaws.com. MX (10) mail.bigjaws.com bigjaws.com. SPF "v=spf1 +ip4:XXX.XXX.XXX.158 +mx ~all" From my understanding of SPF, the SPF status should have been passed: I designate that all email being sent by bigjaws.com from XXX.XXX.XXX.158 are valid/not spam (I added +mx there but I'm not sure if needed). When a mail server receives an email, doesn't it lookup the SPF record of the domain and checks against the IP it got the email from? Checking with spfquery: root@box:~# spfquery -ip XXX.XXX.XXX.158 -sender [email protected] -rcpt-to [email protected] StartError Context: Failed to query MAIL-FROM ErrorCode: (2) Could not find a valid SPF record Error: No DNS data for 'bigjaws.com'. EndError noneneutral Please see http://www.openspf.org/Why?id=employee1%40bigjaws.com&ip=XXX.XXX.XXX.158&receiver=spfquery : Reason: default spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com Received-SPF: neutral (spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com) client-ip=XXX.XXX.XXX.158; [email protected]; If I go to the address listed above (openspf.org) it tells me that the message should have been accepted(!): spfquery rejected a message that claimed an envelope sender address of [email protected]. spfquery received a message from static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) that claimed an envelope sender address of [email protected]. The domain bigjaws.com has authorized static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) to send mail on its behalf, so the message should have been accepted. It is impossible for us to say why it was rejected. What should I do? If the problem persists, contact the bigjaws.com postmaster. Also, here are some headers from an email sent by one of our [email protected] addresses to a gmail.com address (by the way, bigjaws.de listed in the "Received: from" field was the initial domain hosted on the dedicated server before adding the .com one -- both are still listed as separate subscriptions under Plesk). Delivered-To: [email protected] Received: by 10.14.177.70 with SMTP id c46csp289656eem; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) X-Received: by 10.14.102.66 with SMTP id c42mr306186eeg.47.1382515860386; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) Return-Path: <[email protected]> Received: from bigjaws.de (static.158.XXX.XXX.XXX.clients.your-server.de. [XXX.XXX.XXX.158]) by mx.google.com with ESMTPS id l4si19438578eew.161.2013.10.23.01.10.59 for <[email protected]> (version=TLSv1 cipher=RC4-SHA bits=128/128); Wed, 23 Oct 2013 01:10:59 -0700 (PDT) Received-SPF: neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=XXX.XXX.XXX.158; Authentication-Results: mx.google.com; spf=neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=default; d=bigjaws.com; b=WwRAS0WKjp9lO17iMluYPXOHzqRcOueiQT4rPdvy3WFf0QzoXiy6rLfxU/Ra53jL1vlPbwlLNa5gjoJBi7ZwKfUcvs3s02hJI7b3ozl0fEgJtTPKoCfnwl4bLPbtXNFu; h=Received:Received:Message-ID:Date:From:User-Agent:MIME-Version:To:Subject:Content-Type:Content-Transfer-Encoding; Received: (qmail 22722 invoked from network); 23 Oct 2013 10:10:59 +0200 Received: from hostname.static.ISP.com (HELO ?192.168.1.60?) (YYY.YYY.ISP.IP) by static.158.XXX.XXX.XXX.clients.your-server.de. with ESMTPSA (DHE-RSA-AES256-SHA encrypted, authenticated); 23 Oct 2013 10:10:59 +0200 Message-ID: <[email protected]> Date: Wed, 23 Oct 2013 11:11:00 +0300 From: BigJaws Employee <[email protected]> User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64; rv:24.0) Gecko/20100101 Thunderbird/24.0.1 MIME-Version: 1.0 To: [email protected] Subject: test SPF Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit test SPF Any ideas why SPF is not working correctly? Also, are there any DNS settings that are not needed anymore and create a problem?

    Read the article

  • Linux servers seeing bad download performance behind Sonicwall firewall

    - by Joshua Penix
    I'm working with a pair of co-located CentOS Linux servers sitting behind a Sonicwall PRO 2040 Enhanced firewall running in transparent bridge mode. These servers are having a strange problem downloading files more than a few megabytes in size. For example, if I try to wget or FTP a copy of the Linux kernel from kernel.org, the first ~1-2MB will download at 600+K/s, and then throughput will drop off a cliff to 1K/s. I've reviewed all the firewall configuration settings for anything suspicious, but found nothing. More interestingly, I performed the same download with a Windows server sitting behind the same firewall, and it sailed right through at 600+K/s the whole way. Has anyone seen this? Where should I start looking to troubleshoot this problem?

    Read the article

< Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >