out parameter - Page 277

Disk operations freeze Debian

- by Grzenio

Hi, I have just installed Debian testing on my new desktop and I am not very happy with performance - when I perform a disk intensive operation, e.g. upgrade packages in the system, everything seems to freeze, e.g. changing tabs in Iceweasel takes 3 seconds. I run the Debian on my 3 year old Thinkpad X60 ultra-portable, and I don't have these issues. (every single parameter of the laptop is much worse than the desktop). I am using the default packaged kernel and scripts. I run hdparm -t /dev/sda1 And I got around 96GB/s, which is expected. What else can I try to make it work better? EDIT: grzes:/home/ga# hdparm -i /dev/sda /dev/sda: Model=WDC WD15EARS-00Z5B1, FwRev=80.00A80, SerialNo=WD-WMAVU1362357 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50 BuffType=unknown, BuffSize=unknown, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=2930277168 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=no WriteCache=enabled Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7 * signifies the current active mode EDIT2: Even my wife said "on this new computer I can't do anything when I copy the photos from the camera and its much worse than on the old one". So it must be serious. EDIT3: Updated to 2.6.32, but still no improvement EDIT4: I forgot to mention that the new disk is ext4, the old was ext3. EDIT5: Still not solved. I have a P43 ASUS P5QL-E board. Lines from dmesg that seem relevant: [ 0.370850] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.370852] io scheduler noop registered [ 0.370853] io scheduler anticipatory registered [ 0.370854] io scheduler deadline registered [ 0.370876] io scheduler cfq registered (default) ... [ 0.908233] ata_piix 0000:00:1f.2: version 2.13 [ 0.908243] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.908246] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.908275] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.908316] scsi0 : ata_piix [ 0.908374] scsi1 : ata_piix [ 0.909180] ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19 [ 0.909183] ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19 [ 0.909199] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.909202] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.909228] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.909279] scsi2 : ata_piix [ 0.909326] scsi3 : ata_piix [ 0.910021] ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19 [ 0.910024] ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19 [ 0.915575] FDC 0 is a post-1991 82077 ... [ 1.716062] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.716074] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.724318] ata1.00: ATA-8: WDC WD15EARS-00Z5B1, 80.00A80, max UDMA/133 [ 1.724322] ata1.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.740339] ata1.00: configured for UDMA/133 [ 1.740428] scsi 0:0:0:0: Direct-Access ATA WDC WD15EARS-00Z 80.0 PQ: 0 ANSI: 5 [ 1.746788] scsi 6:0:0:0: CD-ROM ASUS DRW-1608P 1.17 PQ: 0 ANSI: 5 ... [ 1.925981] sd 0:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) [ 1.926005] sd 0:0:0:0: [sda] Write Protect is off [ 1.926007] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.926020] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.926092] sda:sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 1.931106] Uniform CD-ROM driver Revision: 3.20 [ 1.931191] sr 6:0:0:0: Attached scsi CD-ROM sr0 ... [ 1.941936] sda1 sda2 sda3 sda4 < sda5 sda6 > [ 1.967691] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.970938] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.970959] sr 6:0:0:0: Attached scsi generic sg1 type 5 ... [ 2.500086] EXT4-fs (sda3): mounted filesystem with ordered data mode ... [ 7.150468] EXT4-fs (sda6): mounted filesystem with ordered data mode

Read the article

mod_mono 'Service Temporarily Unavailable' issue

- by Charlie Somerville

I've deployed an ASP.NET web application on a Linux (Debian) server running Apache 2.2 and mod_mono 1.9 It's working well, however Mono occasionally segfaults and uses the entire CPU which causes the website to stop working and display 'Service Temporarily Unavailable' Killing mono fixes it, but obviously this isn't a good solution. I tailed the system log after this happened and I saw the following error messages from the kernel: Apr 20 01:49:37 charliesomerville kernel: [1596436.204158] mono[17909]: segfault at b645f671 ip b645f671 sp b4ffb604 error 4<6>mono[19047]: segfault at b645f66e ip b645f66e sp b4bf7604 error 4<6>mono[18017]: segfault at b645f66e ip b645f66e sp b52fe604 error 4<6>mono[19668]: segfault at b645f5e6 ip b645f5e6 sp b48f4604 error 4<6>mono[22565]: segfault at b645f674 ip b645f674 sp b45f1604 error 4<6>mono[17700]: segfault at b645f661 ip b645f661 sp b51fd604 error 4<6>mono[19596]: segfault at b645f5e6 ip b645f5e6 sp b49f5604 error 4 Apr 20 01:49:37 charliesomerville kernel: [1596436.208172] mono[23219]: segfault at b645f66e ip b645f66e sp b44f0604 error 4 At the end of Apache's error.log are the following errors: [Tue Apr 20 03:10:23 2010] [error] (70014)End of file found: read_data failed [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 System.ArgumentNullException: null key Parameter name: key at System.Collections.Hashtable.get_Item (System.Object key) [0x00000] at System.Runtime.Serialization.SerializationCallbacks.GetSerializationCallbacks (System.Type t) [0x00000] at System.Runtime.Serialization.ObjectManager.RaiseOnDeserializingEvent (System.Object obj) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectContent (System.IO.BinaryReader reader, System.Runtime.Serialization.Formatters.Binary.TypeMetadata metadata, Int64 objectId, System.Object& objectInstance, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectInstance (System.IO.BinaryReader reader, Boolean isRuntimeObject, Boolean hasTypeInfo, System.Int64& objectId, System.Object& value, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObject (BinaryElement element, System.IO.BinaryReader reader, System.Int64& objectId, System.Object& value, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadNextObject (System.IO.BinaryReader reader) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectGraph (System.IO.BinaryReader reader, Boolean readHeaders, System.Object& result, System.Runtime.Remoting.Messaging.Header[]& headers) [0x00000] at System.Runtime.Serialization.Formatters.Binary.BinaryFormatter.NoCheckDeserialize (System.IO.Stream serializationStream, System.Runtime.Remoting.Messaging.HeaderHandler handler) [0x00000] at System.Runtime.Serialization.Formatters.Binary.BinaryFormatter.Deserialize (System.IO.Stream serializationStream) [0x00000] at System.Runtime.Remoting.Channels.CADSerializer.DeserializeObject (System.IO.MemoryStream mem) [0x00000] at System.Runtime.Remoting.RemotingServices.GetDomainProxy (System.AppDomain domain) [0x00000] at System.AppDomain.CreateDomain (System.String friendlyName, System.Security.Policy.Evidence securityInfo, System.AppDomainSetup info) [0x00000] at System.Web.Hosting.ApplicationHost.CreateApplicationHost (System.Type hostType, System.String virtualDir, System.String physicalDir) [0x00000] at Mono.WebServer.VPathToHost.CreateHost (Mono.WebServer.ApplicationServer server, Mono.WebServer.WebSource webSource) [0x00000] at Mono.WebServer.ApplicationServer.GetApplicationForPath (System.String vhost, Int32 port, System.String path, Boolean defaultToRoot) [0x00000] at (wrapper remoting-invoke-with-check) Mono.WebServer.ApplicationServer:GetApplicationForPath (string,int,string,bool) at Mono.WebServer.ModMonoWorker.GetOrCreateApplication (System.String vhost, Int32 port, System.String filepath, System.String virt) [0x00000] at Mono.WebServer.ModMonoWorker.InnerRun (System.Object state) [0x00000] at Mono.WebServer.ModMonoWorker.Run (System.Object state) [0x00000] [Tue Apr 20 03:10:26 2010] [error] (70014)End of file found: read_data failed [Tue Apr 20 03:10:26 2010] [error] Command stream corrupted, last command was -1 Along with the above errors, Apache's error.log is packed with hundreds (if not thousands) of the following error: Maximum number (20) of concurrent mod_mono requests to /tmp/mod_mono_dashboard_default_2.lock reached. Droping request. At the moment, I'm thinking there might be something wrong with configuration here (it's basically running on out-of-the-box config)

Read the article

Crash in audio resampler with some audio rates - FFMPEG PHP ( Solved! )

- by Olaf Erlandsen

i have a problem with this command( FFMPEG PHP ): Command: ffmpeg -i 62f76f050494f0ed6a5997967c00c0c0.wmv -ss 0 -t 99 -y -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 -f flv 62f76f050494f0ed6a5997967c00c0c0.flv Output: FFmpeg version 0.6.5, Copyright (c) 2000-2010 the FFmpeg developers built on Jan 29 2012 17:52:15 with gcc 4.4.5 20110214 (Red Hat 4.4.5-6) configuration: --prefix=/usr --libdir=/usr/lib64 --shlibdir=/usr/lib64 --mandir=/usr/share/man --incdir=/usr/include --disable-avisynth --extra-cflags='-O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -fPIC' --enable-avfilter --enable-avfilter-lavf --enable-libdc1394 --enable-libdirac --enable-libfaac --enable-libfaad --enable-libfaadbin --enable-libgsm --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared --enable-swscale --enable-vdpau --enable-version3 --enable-x11grab libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.19. 0 / 1.19. 0 libswscale 0.11. 0 / 0.11. 0 libpostproc 51. 2. 0 / 51. 2. 0 [asf @ 0xe81670]max_analyze_duration reached Input #0, asf, from '/var/www/resources/tmp/62f76f050494f0ed6a5997967c00c0c0.wmv': Metadata: WMFSDKVersion : 12.0.7601.17514 WMFSDKNeeded : 0.0.0.0000 IsVBR : 0 Duration: 00:00:50.87, bitrate: 2467 kb/s Stream #0.0: Audio: wmapro, 44100 Hz, stereo, flt, 256 kb/s Stream #0.1: Video: vc1, yuv420p, 950x460 [PAR 1:1 DAR 95:46], 25 fps, 25 tbr, 1k tbn, 25 tbc Output #0, flv, to '/var/www/resources/media/62f76f050494f0ed6a5997967c00c0c0.flv': Metadata: encoder : Lavf52.64.2 Stream #0.0: Video: flv, yuv420p, 950x460 [PAR 1:1 DAR 95:46], q=2-31, 200 kb/s, 1k tbn, 29.97 tbc Stream #0.1: Audio: libmp3lame, 11025 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 -> #0.0 Stream #0.0 -> #0.1 Press [q] to stop encoding frame= 72 fps= 0 q=5.0 size= 0kB time=10.91 bitrate= 0.0kbits/s Multiple frames in a packet from stream 0 Warning, using s16 intermediate sample format for resampling frame= 141 fps=139 q=5.0 size= 103kB time=8.15 bitrate= 103.2kbits/s frame= 220 fps=144 q=5.0 size= 875kB time=10.92 bitrate= 656.6kbits/s frame= 290 fps=143 q=5.0 size= 1525kB time=13.74 bitrate= 909.1kbits/s frame= 356 fps=141 q=5.0 size= 2153kB time=15.99 bitrate=1103.1kbits/s frame= 427 fps=141 q=5.0 size= 2847kB time=18.70 bitrate=1247.0kbits/s frame= 497 fps=141 q=5.0 size= 3771kB time=21.16 bitrate=1460.0kbits/s frame= 575 fps=142 q=5.0 size= 4695kB time=24.61 bitrate=1563.0kbits/s frame= 639 fps=141 q=5.0 size= 5301kB time=26.80 bitrate=1620.2kbits/s frame= 703 fps=139 q=5.0 size= 5829kB time=29.36 bitrate=1626.2kbits/s frame= 774 fps=139 q=5.0 size= 6659kB time=32.39 bitrate=1684.0kbits/s frame= 842 fps=139 q=5.0 size= 7915kB time=35.27 bitrate=1838.6kbits/s frame= 911 fps=139 q=5.0 size= 9011kB time=37.98 bitrate=1943.4kbits/s frame= 975 fps=138 q=5.0 size= 9788kB time=40.59 bitrate=1975.3kbits/s frame= 1041 fps=138 q=5.0 size= 10904kB time=43.83 bitrate=2037.9kbits/s frame= 1115 fps=138 q=5.0 size= 11795kB time=46.24 bitrate=2089.8kbits/s frame= 1183 fps=138 q=5.0 size= 12678kB time=48.74 bitrate=2130.7kbits/s frame= 1247 fps=137 q=5.0 size= 13964kB time=51.36 bitrate=2227.5kbits/s frame= 1271 fps=136 q=5.0 Lsize= 15865kB time=58.86 bitrate=2208.1kbits/s video:15366kB audio:462kB global headers:0kB muxing overhead 0.238956% Problem: Warning, using s16 intermediate sample format for resampling I've also tried changing the parameter From -ar 44100 to -ar 11025 Thanks! Solution: Read this link: http://en.wikipedia.org/wiki/MP3#Bit_rate

Read the article

Mac Terminal.app: Force '^C' to be printed when editing current prompt, then aborting it

- by Stefan Lasiewski

This is the opposite of Prevent “^C” from being printed when aborting editing current prompt. I'm using Bash. When I'm editing the commandline in Bash, and I hit Control-C to abort the commandline, the '^C' character does not display. I would like to see this character. I tried commands like stty -ctlecho and stty ctlecho (which I borrowed from the other question), but this didn't work for me. This behavior seems to be true with my environment on Ubuntu, CentOS and MacOSX. This only happens within Apple's Terminal.App. If I SSH to a remote Linux or FreeBSD box, then ^C is printed. So, this is clearly just a local setting. Update: Here is the output of stty -a, as requested by @quack quixote : $ stty -a speed 9600 baud; 41 rows; 88 columns; lflags: icanon isig iexten echo echoe -echok echoke -echonl echoctl -echoprt -altwerase -noflsh -tostop -flusho pendin -nokerninfo -extproc iflags: -istrip icrnl -inlcr -igncr ixon -ixoff ixany imaxbel iutf8 -ignbrk brkint -inpck -ignpar -parmrk oflags: opost onlcr -oxtabs -onocr -onlret cflags: cread cs8 -parenb -parodd hupcl -clocal -cstopb -crtscts -dsrflow -dtrflow -mdmbuf cchars: discard = ^O; dsusp = ^Y; eof = ^D; eol = <undef>; eol2 = <undef>; erase = ^?; intr = ^C; kill = ^U; lnext = ^V; min = 1; quit = ^\; reprint = ^R; start = ^Q; status = ^T; stop = ^S; susp = ^Z; time = 0; werase = ^W; After typing stty sane, stty -a will output the following. The only difference is the parameter of -iutf8. $ stty sane $ stty -a speed 9600 baud; 41 rows; 157 columns; lflags: icanon isig iexten echo echoe -echok echoke -echonl echoctl -echoprt -altwerase -noflsh -tostop -flusho pendin -nokerninfo -extproc iflags: -istrip icrnl -inlcr -igncr ixon -ixoff ixany imaxbel -iutf8 -ignbrk brkint -inpck -ignpar -parmrk oflags: opost onlcr -oxtabs -onocr -onlret cflags: cread cs8 -parenb -parodd hupcl -clocal -cstopb -crtscts -dsrflow -dtrflow -mdmbuf cchars: discard = ^O; dsusp = ^Y; eof = ^D; eol = <undef>; eol2 = <undef>; erase = ^?; intr = ^C; kill = ^U; lnext = ^V; min = 1; quit = ^\; reprint = ^R; start = ^Q; status = ^T; stop = ^S; susp = ^Z; time = 0; werase = ^W;

Read the article

Why am I getting a 403 error on a POST to a PHP script?

- by John Gallagher

Background I want to allow my users to submit a crash report which will get emailed to me. I'm using UKCrashReporter with the bundled PHP script I've modified. This code does a POST to a specified URL along with the crash report. I'm on a shared server running Linux. My main domain is synapticmishap.co.uk. The Problem When I send the crash report off, on the Cocoa side, it reports as having sent it successfully, but I don't receive an email. The code has been used in lots of other well established Cocoa projects and it was working for me a few months ago. That leads me to conclude that the problems are related to my web server setup, something I know almost nothing about. When I look at my log files, I see entries like this: IP Redacted - - [10/Jun/2010:09:47:53 +0100] "POST /synapticmishap/crashreportform.php HTTP/1.1" 403 74 "-" "UKCrashReporter" What I've tried I've tried accessing the page at http://synapticmishap.co.uk/synapticmishap/crashreportform.php via a browser. It loads fine. I've made sure the permissions on this php script are set so anyone can execute it. I've tried removing the deny entries from the section of .htaccess at various levels starting with root. I've downloaded the URLParams plugin for Firefox which allows you to simulate POSTs. I put in the URL above and tried a post with "crashlog" as the parameter and "test" as the value. This generated a 200 log entry in my log file - it seemed to work, although no mail message was sent. Code I've got the following at http://synapticmishap.co.uk/synapticmishap/crashreportform.php. I've simplified it to just the bare bones in an effort to get it working. <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html> <head> <title>Crash Report</title> </head> <body> <p>This page contains super special magic which submits a crash report item to me.</p> <p>Nothing to see here - move along.</p> <?php mail( "[email protected]", "Crash Report", "\r\n\r\nThis is a test."); ?> </body> </html> This is my top level .htaccess file: RewriteEngine on # -FrontPage- IndexIgnore .htaccess */.??* *~ *# */HEADER* */README* */_vti* <Limit GET POST> order deny,allow deny from all allow from all </Limit> <Limit PUT DELETE> order deny,allow deny from all </Limit> Options All -Indexes RewriteCond %{HTTP_HOST} ^synapticmishap.co.uk$ [OR] RewriteCond %{HTTP_HOST} ^www.synapticmishap.co.uk$ RewriteCond %{HTTP_HOST} ^lapsusapp.co.uk$ [OR] RewriteCond %{HTTP_HOST} ^www.lapsusapp.co.uk$ RewriteRule ^/?$ "http\:\/\/synapticmishap\.co\.uk\/synapticmishap\/lapsuspromo\/" [R=301,L] RewriteCond %{HTTP_HOST} ^jgtutoring.co.uk$ [OR] RewriteCond %{HTTP_HOST} ^www.jgtutoring.co.uk$ RewriteRule ^/?$ "http\:\/\/synapticmishap\.co\.uk\/tutoring" [R=301,L] RewriteCond %{HTTP_HOST} ^synapticmishap.co.uk$ [OR] RewriteCond %{HTTP_HOST} ^www.synapticmishap.co.uk$ RewriteRule ^/?$ "http\:\/\/synapticmishap\.co\.uk\/synapticmishap" [R=301,L] RewriteCond %{HTTP_HOST} ^jgediting.co.uk$ [OR] RewriteCond %{HTTP_HOST} ^www.jgediting.co.uk$ RewriteRule ^/?$ "http\:\/\/synapticmishap\.co\.uk\/editing" [R=301,L] RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://synapticmishap.co.uk/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://synapticmishap.co.uk$ [NC] RewriteCond %{HTTP_REFERER} !^http://www.synapticmishap.co.uk/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://www.synapticmishap.co.uk$ [NC] RewriteCond %{HTTP_REFERER} !^http://synapticmishap.co.uk/synapticmishap/crashreportform.php/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://synapticmishap.co.uk/synapticmishap/crashreportform.php$ [NC] RewriteRule .*\.(jpg|jpeg|gif|png|bmp)$ - [F,NC] Help! I'm at the end of my tether with this and I'm in a very unfamiliar space with all this web stuff. I'd be most appreciative of any thoughts people had on why this isn't working. Thanks.

Read the article

vlans on openvz, centos 6

- by arheops

i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

Read the article

Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

- by Joy

The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

Read the article

Using jQuery and SPServices to Display List Items

- by Bil Simser

I had an interesting challenge recently that I turned to Marc Anderson’s wonderful SPServices project for. If you haven’t already seen or used SPServices, please do. It’s a jQuery library that does primarily two things. First, it wraps up all of the SharePoint web services in a nice little AJAX wrapper for use in JavaScript. Second, it enhances the form editing of items in SharePoint so you’re not hacking up your List Form pages. My challenge was simple but interesting. The user wanted to display a SharePoint item page (DispForm.aspx, which already had some customization on it to display related items via this blog post from Codeless Solutions for SharePoint) but launch from an external application using the value of one of the fields in the SharePoint list. For simplicity let’s say my list is a list of customers and the related list is a list of orders for that customer. It would look something like this (click on the item to see the full image): Your first thought might be, that’s easy! Display the customer information using a DataView Web Part and filter the item using a query string to match the customer number. However there are a few problems with this idea: You’ll need to build a custom page and then attach that related orders view to it. This is a bit of a problem because the solution from Codeless Solutions relies on the Title field on the page to be displayed. On a custom page you would have to recreate all of the elements found on the DispForm.aspx page so the related view would work. The DataView Web Part doesn’t look *exactly* like what the out of the box display form page does. Not a huge problem and can be overcome with some CSS style overrides but still, more work. A DVWP showing a single record doesn’t have the same toolbar that you would using the DispForm.aspx. Not a show-stopper and you can rebuild the toolbar but it’s going to potentially require code and then there’s the security trimming, etc. that you have to get right. DVWPs are not automatically updated if you add a column to the list like DispForm.aspx is. Work, work, work. For these reasons I thought it would be easier to take the already existing (modified) DispForm.aspx page and just add some jQuery magic to the page to find the item. Why do we need to find it? DispForm.aspx relies on a querystring parameter called “ID” which then displays whatever that item ID number is in the list. Trouble is, when you’re coming in from an external app via a link, you don’t know what that internal ID is (and frankly shouldn’t). I don’t like exposing internal SharePoint IDs to the outside world for the same reason I don’t do it with database IDs. They’re internal and while it’s find to use on the site itself you don’t want external links using it. It’s volatile and can change (delete one item then re-add it back with the same data and watch any ID references break). The next thought might be to call a SharePoint web service with a CAML query to get the item ID number using some criteria (in this case, the customer number). That’s great if you have that ability but again we had an existing application we were just adding a link to. The last thing I wanted to do was to crack open the code on that sucker and start calling web services (primarily because it’s Java, but really I’m a lazy geek). However if you’re doing this and have access to call a web service that would be an option. Back to this problem, how do I a) find a SharePoint List Item based on some field value other than ID and b) make it low impact so I can just construct a URL to it? That’s where jQuery and SPServices came to the rescue. After spending a few hours of emails back and forth with Marc and a couple of phone calls (and updating jQuery to the latest version, duh!) it was a simple answer. First we need a reference to a) jQuery b) SPServices and c) our script. I just dropped a Content Editor Web Part, the Swiss Army Knives of Web Parts, onto the DispForm.aspx page and added these lines: <script type="text/javascript" src="http://intranet/JavaScript/jquery-1.4.2.min.js"></script> <script type="text/javascript" src="http://intranet/JavaScript/jquery.SPServices-0.5.3.min.js"></script> <script type="text/javascript" src="http://intranet/JavaScript/RedirectToID.js"> </script> Update it to point to where you keep your scripts located. I prefer to keep them all in Document Libraries as I can make changes to them without having to remote into the server (and on a multiple web front end, that’s just a PITA), it provides me with version control of sorts, and it’s quick to add new plugins and scripts. Now we can look at our RedirectToID.js script. This invokes the SPServices Library to call the GetListItems method of the Lists web service and then rewrites the URL to DispForm.aspx to use the correct SharePoint ID (the internal one). $(document).ready(function(){ var queryStringValues = $().SPServices.SPGetQueryString(); var id = queryStringValues["ID"]; if(id == "0") { var customer = queryStringValues["CustomerNumber"]; var query = "<Query><Where><Eq><FieldRef Name='CustomerNumber'/><Value Type='Text'>" + customer + "</Value></Eq></Where></Query>"; var url = window.location; $().SPServices({ operation: "GetListItems", listName: "Customers", async: false, CAMLQuery: query, completefunc: function (xData, Status) { $(xData.responseXML).find("[nodeName=z:row]").each(function(){ id = $(this).attr("ows_ID"); url = $().SPServices.SPGetCurrentSite() + "/Lists/Customers/DispForm.aspx?ID=" + id; window.location = url; }); } }); } }); What’s happening here? Line 3: We call SPServices.SPGetQueryString to get an array of query string values (a handy function in the library as I had 15 lines of code to do this which is now gone). Line 4: Extract the ID value from the query string Line 6: If we pass in “0” it means we’re looking up a field value. This allows DispForm.aspx to work like normal with SharePoint lists but lookup our values when invoked. Why ID at all? DispForm.aspx doesn’t work unless you pass in something and “0” is a *magic* number that will invoke the page but not lookup a value in the database. Line 8-15: Extract the CustomerNumber query string value, build a CAML query to find it then call the GetListitems method using SPServices Line 16: Process the results in our completefunc to iterate over all the rows (there should only be one) and extract the real ID of the item Line 17-20: Build a new URL based on the site (using a call to SPGetCurrentSite) and append our real ID to redirect to the DispForm.aspx page As you can see, it dynamically creates a CAML query for the call to the web service using the passed in value. You could even make this generic to take in different query strings, one for the field name to search for and the other for the value to find. That way it could be used for any field you want. For example you could bring up the correct item on the DispForm.aspx page based on customer name with something like this: http://myserver/Lists/Customers/DispForm.aspx?ID=0&FilterId=CustomerName&FilterValue=Sony Use your imagination. Some people would opt for building a custom page with a DVWP but if you want to leverage all the functionality of DispForm.aspx this might come in handy if you don’t want to rely on internal SharePoint IDs.

Read the article

ASP.NET MVC 3 Hosting :: New Features in ASP.NET MVC 3

- by mbridge

Razor View Engine The Razor view engine is a new view engine option for ASP.NET MVC that supports the Razor templating syntax. The Razor syntax is a streamlined approach to HTML templating designed with the goal of being a code driven minimalist templating approach that builds on existing C#, VB.NET and HTML knowledge. The result of this approach is that Razor views are very lean and do not contain unnecessary constructs that get in the way of you and your code. ASP.NET MVC 3 Preview 1 only supports C# Razor views which use the .cshtml file extension. VB.NET support will be enabled in later releases of ASP.NET MVC 3. For more information and examples, see Introducing “Razor” – a new view engine for ASP.NET on Scott Guthrie’s blog. Dynamic View and ViewModel Properties A new dynamic View property is available in views, which provides access to the ViewData object using a simpler syntax. For example, imagine two items are added to the ViewData dictionary in the Index controller action using code like the following: public ActionResult Index() { ViewData["Title"] = "The Title"; ViewData["Message"] = "Hello World!"; } Those properties can be accessed in the Index view using code like this: <h2>View.Title</h2> <p>View.Message</p> There is also a new dynamic ViewModel property in the Controller class that lets you add items to the ViewData dictionary using a simpler syntax. Using the previous controller example, the two values added to the ViewData dictionary can be rewritten using the following code: public ActionResult Index() { ViewModel.Title = "The Title"; ViewModel.Message = "Hello World!"; } “Add View” Dialog Box Supports Multiple View Engines The Add View dialog box in Visual Studio includes extensibility hooks that allow it to support multiple view engines, as shown in the following figure: Service Location and Dependency Injection Support ASP.NET MVC 3 introduces improved support for applying Dependency Injection (DI) via Inversion of Control (IoC) containers. ASP.NET MVC 3 Preview 1 provides the following hooks for locating services and injecting dependencies: - Creating controller factories. - Creating controllers and setting dependencies. - Setting dependencies on view pages for both the Web Form view engine and the Razor view engine (for types that derive from ViewPage, ViewUserControl, ViewMasterPage, WebViewPage). - Setting dependencies on action filters. Using a Dependency Injection container is not required in order for ASP.NET MVC 3 to function properly. Global Filters ASP.NET MVC 3 allows you to register filters that apply globally to all controller action methods. Adding a filter to the global filters collection ensures that the filter runs for all controller requests. To register an action filter globally, you can make the following call in the Application_Start method in the Global.asax file: GlobalFilters.Filters.Add(new MyActionFilter()); The source of global action filters is abstracted by the new IFilterProvider interface, which can be registered manually or by using Dependency Injection. This allows you to provide your own source of action filters and choose at run time whether to apply a filter to an action in a particular request. New JsonValueProviderFactory Class The new JsonValueProviderFactory class allows action methods to receive JSON-encoded data and model-bind it to an action-method parameter. This is useful in scenarios such as client templating. Client templates enable you to format and display a single data item or set of data items by using a fragment of HTML. ASP.NET MVC 3 lets you connect client templates easily with an action method that both returns and receives JSON data. Support for .NET Framework 4 Validation Attributes and IvalidatableObject The ValidationAttribute class was improved in the .NET Framework 4 to enable richer support for validation. When you write a custom validation attribute, you can use a new IsValid overload that provides a ValidationContext instance. This instance provides information about the current validation context, such as what object is being validated. This change enables scenarios such as validating the current value based on another property of the model. The following example shows a sample custom attribute that ensures that the value of PropertyOne is always larger than the value of PropertyTwo: public class CompareValidationAttribute : ValidationAttribute { protected override ValidationResult IsValid(object value, ValidationContext validationContext) { var model = validationContext.ObjectInstance as SomeModel; if (model.PropertyOne > model.PropertyTwo) { return ValidationResult.Success; } return new ValidationResult("PropertyOne must be larger than PropertyTwo"); } } Validation in ASP.NET MVC also supports the .NET Framework 4 IValidatableObject interface. This interface allows your model to perform model-level validation, as in the following example: public class SomeModel : IValidatableObject { public int PropertyOne { get; set; } public int PropertyTwo { get; set; } public IEnumerable<ValidationResult> Validate(ValidationContext validationContext) { if (PropertyOne <= PropertyTwo) { yield return new ValidationResult( "PropertyOne must be larger than PropertyTwo"); } } } New IClientValidatable Interface The new IClientValidatable interface allows the validation framework to discover at run time whether a validator has support for client validation. This interface is designed to be independent of the underlying implementation; therefore, where you implement the interface depends on the validation framework in use. For example, for the default data annotations-based validator, the interface would be applied on the validation attribute. Support for .NET Framework 4 Metadata Attributes ASP.NET MVC 3 now supports .NET Framework 4 metadata attributes such as DisplayAttribute. New IMetadataAware Interface The new IMetadataAware interface allows you to write attributes that simplify how you can contribute to the ModelMetadata creation process. Before this interface was available, you needed to write a custom metadata provider in order to have an attribute provide extra metadata. This interface is consumed by the AssociatedMetadataProvider class, so support for the IMetadataAware interface is automatically inherited by all classes that derive from that class (notably, the DataAnnotationsModelMetadataProvider class). New Action Result Types In ASP.NET MVC 3, the Controller class includes two new action result types and corresponding helper methods. HttpNotFoundResult Action The new HttpNotFoundResult action result is used to indicate that a resource requested by the current URL was not found. The status code is 404. This class derives from HttpStatusCodeResult. The Controller class includes an HttpNotFound method that returns an instance of this action result type, as shown in the following example: public ActionResult List(int id) { if (id < 0) { return HttpNotFound(); } return View(); } HttpStatusCodeResult Action The new HttpStatusCodeResult action result is used to set the response status code and description. Permanent Redirect The HttpRedirectResult class has a new Boolean Permanent property that is used to indicate whether a permanent redirect should occur. A permanent redirect uses the HTTP 301 status code. Corresponding to this change, the Controller class now has several methods for performing permanent redirects: - RedirectPermanent - RedirectToRoutePermanent - RedirectToActionPermanent These methods return an instance of HttpRedirectResult with the Permanent property set to true. Breaking Changes The order of execution for exception filters has changed for exception filters that have the same Order value. In ASP.NET MVC 2 and earlier, exception filters on the controller with the same Order as those on an action method were executed before the exception filters on the action method. This would typically be the case when exception filters were applied without a specified order Order value. In MVC 3, this order has been reversed in order to allow the most specific exception handler to execute first. As in earlier versions, if the Order property is explicitly specified, the filters are run in the specified order. Known Issues When you are editing a Razor view (CSHTML file), the Go To Controller menu item in Visual Studio will not be available, and there are no code snippets.

Read the article

Windows 7 Phone Database – Querying with Views and Filters

- by SeanMcAlinden

I’ve just added a feature to Rapid Repository to greatly improve how the Windows 7 Phone Database is queried for performance (This is in the trunk not in Release V1.0). The main concept behind it is to create a View Model class which would have only the minimum data you need for a page. This View Model is then stored and retrieved rather than the whole list of entities. Another feature of the views is that they can be pre-filtered to even further improve performance when querying. You can download the source from the Microsoft Codeplex site http://rapidrepository.codeplex.com/. Setting up a view Lets say you have an entity that stores lots of data about a game result for example: GameScore entity public class GameScore : IRapidEntity { public Guid Id { get; set; } public string GamerId {get;set;} public string Name { get; set; } public Double Score { get; set; } public Byte[] ThumbnailAvatar { get; set; } public DateTime DateAdded { get; set; } } On your page you want to display a list of scores but you only want to display the score and the date added, you create a View Model for displaying just those properties. GameScoreView public class GameScoreView : IRapidView { public Guid Id { get; set; } public Double Score { get; set; } public DateTime DateAdded { get; set; } } Now you have the view model, the first thing to do is set up the view at application start up. This is done using the following syntax. View Setup public MainPage() { RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score }); } As you can see, using a little bit of lambda syntax, you put in the code for constructing a single view, this is used internally for mapping an entity to a view. *Note* you do not need to map the Id property, this is done automatically, a view model id will always be the same as it’s corresponding entity. Adding Filters One of the cool features of the view is that you can add filters to limit the amount of data stored in the view, this will dramatically improve performance. You can add multiple filters using the fluent syntax if required. In this example, lets say that you will only ever show the scores for the last 10 days, you could add a filter like the following: Add single filter public MainPage() { RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score }) .AddFilter(x => x.DateAdded > DateTime.Now.AddDays(-10)); } If you wanted to further limit the data, you could also say only scores above 100: Add multiple filters public MainPage() { RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score }) .AddFilter(x => x.DateAdded > DateTime.Now.AddDays(-10)) .AddFilter(x => x.Score > 100); } Querying the view model So the important part is how to query the data. This is done using the repository, there is a method called Query which accepts the type of view as a generic parameter (you can have multiple View Model types per entity type) You can either use the result of the query method directly or perform further querying on the result is required. Querying the View public void DisplayScores() { RapidRepository<GameScore> repository = new RapidRepository<GameScore>(); List<GameScoreView> scores = repository.Query<GameScoreView>(); // display logic } Further Filtering public void TodaysScores() { RapidRepository<GameScore> repository = new RapidRepository<GameScore>(); List<GameScoreView> todaysScores = repository.Query<GameScoreView>().Where(x => x.DateAdded > DateTime.Now.AddDays(-1)).ToList(); // display logic } Retrieving the actual entity Retrieving the actual entity can be done easily by using the GetById method on the repository. Say for example you allow the user to click on a specific score to get further information, you can use the Id populated in the returned View Model GameScoreView and use it directly on the repository to retrieve the full entity. Get Full Entity public void GetFullEntity(Guid gameScoreViewId) { RapidRepository<GameScore> repository = new RapidRepository<GameScore>(); GameScore fullEntity = repository.GetById(gameScoreViewId); // display logic } Synchronising The View If you are upgrading from Rapid Repository V1.0 and are likely to have data in the repository already, you will need to perform a synchronisation to ensure the views and entities are fully in sync. You can either do this as a one off during the application upgrade or if you are a little more cautious, you could run this at each application start up. Synchronise the view public void MyUpgradeTasks() { RapidRepository<GameScore>.SynchroniseView<GameScoreView>(); } It’s worth noting that in normal operation, the view keeps itself in sync with the entities so this is only really required if you are upgrading from V1.0 to V2.0 when it gets released shortly. Summary I really hope you like this feature, it will be great for performance and I believe supports good practice by promoting the use of View Models for specific pages. I’m hoping to produce a beta for this over the next few days, I just want to add some more tests and hopefully iron out any bugs. I would really appreciate any thoughts on this feature and would really love to know of any bugs you find. You can download the source from the following : http://rapidrepository.codeplex.com/ Kind Regards, Sean McAlinden.

Read the article

Installing Lubuntu 14.04.1 forcepae fails

- by Rantanplan

I tried to install Lubuntu 14.04.1 from a CD. First, I chose Try Lubuntu without installing which gave: ERROR: PAE is disabled on this Pentium M (PAE can potentially be enabled with kernel parameter "forcepae" ... Following the description on https://help.ubuntu.com/community/PAE, I used forcepae and tried Try Lubuntu without installing again. That worked fine. dmesg | grep -i pae showed: [ 0.000000] Kernel command line: file=/cdrom/preseed/lubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- forcepae [ 0.008118] PAE forced! On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Finally, I rebooted once more and tried Check disc for defects with forcepae option; no errors have been found. Now, I am wondering how to find the error or whether it would be better to follow advice c in https://help.ubuntu.com/community/PAE: "Move the hard disk to a computer on which the processor has PAE capability and PAE flag (that is, almost everything else than a Banias). Install the system as usual but don't add restricted drivers. After the install move the disk back." Thanks for some hints! Perhaps some of the following can help: On Lubuntu 12.04: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr mce cx8 mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2 bogomips : 1284.76 clflush size : 64 cache_alignment : 64 address sizes : 32 bits physical, 32 bits virtual power management: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise cpuid eax in eax ebx ecx edx 00000000 00000002 756e6547 6c65746e 49656e69 00000001 000006d6 00000816 00000180 afe9f9bf 00000002 02b3b001 000000f0 00000000 2c04307d 80000000 80000004 00000000 00000000 00000000 80000001 00000000 00000000 00000000 00000000 80000002 20202020 20202020 65746e49 2952286c 80000003 6e655020 6d756974 20295228 7270204d 80000004 7365636f 20726f73 30352e31 007a4847 Vendor ID: "GenuineIntel"; CPUID level 2 Intel-specific functions: Version 000006d6: Type 0 - Original OEM Family 6 - Pentium Pro Model 13 - Stepping 6 Reserved 0 Brand index: 22 [not in table] Extended brand string: " Intel(R) Pentium(R) M processor 1.50GHz" CLFLUSH instruction cache line size: 8 Feature flags afe9f9bf: FPU Floating Point Unit VME Virtual 8086 Mode Enhancements DE Debugging Extensions PSE Page Size Extensions TSC Time Stamp Counter MSR Model Specific Registers MCE Machine Check Exception CX8 COMPXCHG8B Instruction SEP Fast System Call MTRR Memory Type Range Registers PGE PTE Global Flag MCA Machine Check Architecture CMOV Conditional Move and Compare Instructions FGPAT Page Attribute Table CLFSH CFLUSH instruction DS Debug store ACPI Thermal Monitor and Clock Ctrl MMX MMX instruction set FXSR Fast FP/MMX Streaming SIMD Extensions save/restore SSE Streaming SIMD Extensions instruction set SSE2 SSE2 extensions SS Self Snoop TM Thermal monitor 31 reserved TLB and cache info: b0: unknown TLB/cache descriptor b3: unknown TLB/cache descriptor 02: Instruction TLB: 4MB pages, 4-way set assoc, 2 entries f0: unknown TLB/cache descriptor 7d: unknown TLB/cache descriptor 30: unknown TLB/cache descriptor 04: Data TLB: 4MB pages, 4-way set assoc, 8 entries 2c: unknown TLB/cache descriptor On Lubuntu 14.04.1 live-CD with forcepae: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2 bogomips : 1284.68 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 32 bits virtual power management: uname -a Linux lubuntu 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04.1 LTS Release: 14.04 Codename: trusty cpuid CPU 0: vendor_id = "GenuineIntel" version information (1/eax): processor type = primary processor (0) family = Intel Pentium Pro/II/III/Celeron/Core/Core 2/Atom, AMD Athlon/Duron, Cyrix M2, VIA C3 (6) model = 0xd (13) stepping id = 0x6 (6) extended family = 0x0 (0) extended model = 0x0 (0) (simple synth) = Intel Pentium M (Dothan B1) / Celeron M (Dothan B1), 90nm miscellaneous (1/ebx): process local APIC physical ID = 0x0 (0) cpu count = 0x0 (0) CLFLUSH line size = 0x8 (8) brand index = 0x16 (22) brand id = 0x16 (22): Intel Pentium M, .13um feature information (1/edx): x87 FPU on chip = true virtual-8086 mode enhancement = true debugging extensions = true page size extensions = true time stamp counter = true RDMSR and WRMSR support = true physical address extensions = false machine check exception = true CMPXCHG8B inst. = true APIC on chip = false SYSENTER and SYSEXIT = true memory type range registers = true PTE global bit = true machine check architecture = true conditional move/compare instruction = true page attribute table = true page size extension = false processor serial number = false CLFLUSH instruction = true debug store = true thermal monitor and clock ctrl = true MMX Technology = true FXSAVE/FXRSTOR = true SSE extensions = true SSE2 extensions = true self snoop = true hyper-threading / multi-core supported = false therm. monitor = true IA64 = false pending break event = true feature information (1/ecx): PNI/SSE3: Prescott New Instructions = false PCLMULDQ instruction = false 64-bit debug store = false MONITOR/MWAIT = false CPL-qualified debug store = false VMX: virtual machine extensions = false SMX: safer mode extensions = false Enhanced Intel SpeedStep Technology = true thermal monitor 2 = true SSSE3 extensions = false context ID: adaptive or shared L1 data = false FMA instruction = false CMPXCHG16B instruction = false xTPR disable = false perfmon and debug = false process context identifiers = false direct cache access = false SSE4.1 extensions = false SSE4.2 extensions = false extended xAPIC support = false MOVBE instruction = false POPCNT instruction = false time stamp counter deadline = false AES instruction = false XSAVE/XSTOR states = false OS-enabled XSAVE/XSTOR = false AVX: advanced vector extensions = false F16C half-precision convert instruction = false RDRAND instruction = false hypervisor guest status = false cache and TLB information (2): 0xb0: instruction TLB: 4K, 4-way, 128 entries 0xb3: data TLB: 4K, 4-way, 128 entries 0x02: instruction TLB: 4M pages, 4-way, 2 entries 0xf0: 64 byte prefetching 0x7d: L2 cache: 2M, 8-way, sectored, 64 byte lines 0x30: L1 cache: 32K, 8-way, 64 byte lines 0x04: data TLB: 4M pages, 4-way, 8 entries 0x2c: L1 data cache: 32K, 8-way, 64 byte lines extended feature flags (0x80000001/edx): SYSCALL and SYSRET instructions = false execution disable = false 1-GB large page support = false RDTSCP = false 64-bit extensions technology available = false Intel feature flags (0x80000001/ecx): LAHF/SAHF supported in 64-bit mode = false LZCNT advanced bit manipulation = false 3DNow! PREFETCH/PREFETCHW instructions = false brand = " Intel(R) Pentium(R) M processor 1.50GHz" (multi-processing synth): none (multi-processing method): Intel leaf 1 (synth) = Intel Pentium M (Dothan B1), 90nm

Read the article

TFS 2010 Build Custom Activity for Merging Assemblies

- by Jakob Ehn

*** The sample build process template discussed in this post is available for download from here: http://cid-ee034c9f620cd58d.office.live.com/self.aspx/BlogSamples/ILMerge.xaml *** In my previous post I talked about library builds that we use to build and replicate dependencies between applications in TFS. This is typically used for common libraries and tools that several other application need to reference. When the libraries grow in size over time, so does the number of assemblies. So all solutions that uses the common library must reference all the necessary assemblies that they need, and if we for example do a refactoring and extract some code into a new assembly, all the clients must update their references to reflect these changes, otherwise it won’t compile. To improve on this, we use a tool from Microsoft Research called ILMerge (Download from here). It can be used to merge several assemblies into one assembly that contains all types. If you haven’t used this tool before, you should check it out. Previously I have implemented this in builds using a simple batch file that contains the full command, something like this: "%ProgramFiles(x86)%\microsoft\ilmerge\ilmerge.exe" /target:library /attr:ClassLibrary1.bl.dll /out:MyNewLibrary.dll ClassLibrary1.dll ClassLibrar2.dll ClassLibrary3.dll This merges 3 assemblies (ClassLibrary1, 2 and 3) into a new assembly called MyNewLibrary.dll. It will copy the attributes (file version, product version etc..) from ClassLibrary1.dll, using the /attr switch. For more info on ILMerge command line tool, see the above link. This approach works, but requires a little bit too much knowledge for the developers creating builds, therefor I have implemented a custom activity that wraps the use of ILMerge. This makes it much simpler to setup a new build definition and have the build automatically do the merging. The usage of the activity is then implemented as part of the Library Build process template mentioned in the previous post. For this article I have just created a simple build process template that only performs the ILMerge operation. Below is the code for the custom activity. To make it compile, you need to reference the ILMerge.exe assembly. /// <summary> /// Activity for merging a list of assembies into one, using ILMerge /// </summary> public sealed class ILMergeActivity : BaseCodeActivity { /// <summary> /// A list of file paths to the assemblies that should be merged /// </summary> [RequiredArgument] public InArgument<IEnumerable<string>> InputAssemblies { get; set; } /// <summary> /// Full path to the generated assembly /// </summary> [RequiredArgument] public InArgument<string> OutputFile { get; set; } /// <summary> /// Which input assembly that the attibutes for the generated assembly should be copied from. /// Optional. If not specified, the first input assembly will be used /// </summary> public InArgument<string> AttributeFile { get; set; } /// <summary> /// Kind of assembly to generate, dll or exe /// </summary> public InArgument<TargetKindEnum> TargetKind { get; set; } // If your activity returns a value, derive from CodeActivity<TResult> // and return the value from the Execute method. protected override void Execute(CodeActivityContext context) { string message = InputAssemblies.Get(context).Aggregate("", (current, assembly) => current + (assembly + " ")); TrackMessage(context, "Merging " + message + " into " + OutputFile.Get(context)); ILMerge m = new ILMerge(); m.SetInputAssemblies(InputAssemblies.Get(context).ToArray()); m.TargetKind = TargetKind.Get(context) == TargetKindEnum.Dll ? ILMerge.Kind.Dll : ILMerge.Kind.Exe; m.OutputFile = OutputFile.Get(context); m.AttributeFile = !String.IsNullOrEmpty(AttributeFile.Get(context)) ? AttributeFile.Get(context) : InputAssemblies.Get(context).First(); m.SetTargetPlatform(RuntimeEnvironment.GetSystemVersion().Substring(0,2), RuntimeEnvironment.GetRuntimeDirectory()); m.Merge(); TrackMessage(context, "Generated " + m.OutputFile); } } [Browsable(true)] public enum TargetKindEnum { Dll, Exe } NB: The activity inherits from a BaseCodeActivity class which is an internal helper class which contains some methods and properties useful for moste custom activities. In this case, it uses the TrackeMessage method for writing to the build log. You either need to remove the TrackMessage method calls, or implement this yourself (which is not very hard… ) The custom activity has the following input arguments: InputAssemblies A list with the (full) paths to the assemblies to merge OutputFile The name of the resulting merged assembly AttributeFile Which assembly to use as the template for the attribute of the merged assembly. This argument is optional and if left blank, the first assembly in the input list is used TargetKind Decides what type of assembly to create, can be either a dll or an exe Of course, there are more switches to the ILMerge.exe, and these can be exposed as input arguments as well if you need it. To show how the custom activity can be used, I have attached a build process template (see link at the top of this post) that merges the output of the projects being built (CommonLibrary.dll and CommonLibrary2.dll) into a merged assembly (NewLibrary.dll). The build process template has the following custom process parameters: The Assemblies To Merge argument is passed into a FindMatchingFiles activity to located all assemblies that are located in the BinariesDirectory folder after the compilation has been performed by Team Build. Here is the complete sequence of activities that performs the merge operation. It is located at the end of the Try, Compile, Test and Associate… sequence: It splits the AssembliesToMerge parameter and appends the full path (using the BinariesDirectory variable) and then enumerates the matching files using the FindMatchingFiles activity. When running the build, you can see that it merges two assemblies into a new one: And the merged assembly (and associated pdb file) is copied to the drop location together with the rest of the assemblies:

Read the article

Dependency Injection in ASP.NET MVC NerdDinner App using Ninject

- by shiju

In this post, I am applying Dependency Injection to the NerdDinner application using Ninject. The controllers of NerdDinner application have Dependency Injection enabled constructors. So we can apply Dependency Injection through constructor without change any existing code. A Dependency Injection framework injects the dependencies into a class when the dependencies are needed. Dependency Injection enables looser coupling between classes and their dependencies and provides better testability of an application and it removes the need for clients to know about their dependencies and how to create them. If you are not familiar with Dependency Injection and Inversion of Control (IoC), read Martin Fowler’s article Inversion of Control Containers and the Dependency Injection pattern. The Open Source Project NerDinner is a great resource for learning ASP.NET MVC. A free eBook provides an end-to-end walkthrough of building NerdDinner.com application. The free eBook and the Open Source Nerddinner application are extremely useful if anyone is trying to lean ASP.NET MVC. The first release of Nerddinner was as a sample for the first chapter of Professional ASP.NET MVC 1.0. Currently the application is updating to ASP.NET MVC 2 and you can get the latest source from the source code tab of Nerddinner at http://nerddinner.codeplex.com/SourceControl/list/changesets. I have taken the latest ASP.NET MVC 2 source code of the application and applied Dependency Injection using Ninject and Ninject extension Ninject.Web.Mvc.Ninject & Ninject.Web.MvcNinject is available at http://github.com/enkari/ninject and Ninject.Web.Mvc is available at http://github.com/enkari/ninject.web.mvcNinject is a lightweight and a great dependency injection framework for .NET. Ninject is a great choice of dependency injection framework when building ASP.NET MVC applications. Ninject.Web.Mvc is an extension for ninject which providing integration with ASP.NET MVC.Controller constructors and dependencies of NerdDinner application Listing 1 – Constructor of DinnersController public DinnersController(IDinnerRepository repository) { dinnerRepository = repository; } Listing 2 – Constrcutor of AccountControllerpublic AccountController(IFormsAuthentication formsAuth, IMembershipService service) { FormsAuth = formsAuth ?? new FormsAuthenticationService(); MembershipService = service ?? new AccountMembershipService(); } Listing 3 – Constructor of AccountMembership – Concrete class of IMembershipService public AccountMembershipService(MembershipProvider provider) { _provider = provider ?? Membership.Provider; } Dependencies of NerdDinnerDinnersController, RSVPController SearchController and ServicesController have a dependency with IDinnerRepositiry. The concrete implementation of IDinnerRepositiry is DinnerRepositiry. AccountController has dependencies with IFormsAuthentication and IMembershipService. The concrete implementation of IFormsAuthentication is FormsAuthenticationService and the concrete implementation of IMembershipService is AccountMembershipService. The AccountMembershipService has a dependency with ASP.NET Membership Provider. Dependency Injection in NerdDinner using NinjectThe below steps will configure Ninject to apply controller injection in NerdDinner application.Step 1 – Add reference for NinjectOpen the NerdDinner application and add reference to Ninject.dll and Ninject.Web.Mvc.dll. Both are available from http://github.com/enkari/ninject and http://github.com/enkari/ninject.web.mvcStep 2 – Extend HttpApplication with NinjectHttpApplication Ninject.Web.Mvc extension allows integration between the Ninject and ASP.NET MVC. For this, you have to extend your HttpApplication with NinjectHttpApplication. Open the Global.asax.cs and inherit your MVC application from NinjectHttpApplication instead of HttpApplication. public class MvcApplication : NinjectHttpApplication Then the Application_Start method should be replace with OnApplicationStarted method. Inside the OnApplicationStarted method, call the RegisterAllControllersIn() method. protected override void OnApplicationStarted() { AreaRegistration.RegisterAllAreas(); RegisterRoutes(RouteTable.Routes); ViewEngines.Engines.Clear(); ViewEngines.Engines.Add(new MobileCapableWebFormViewEngine()); RegisterAllControllersIn(Assembly.GetExecutingAssembly()); } The RegisterAllControllersIn method will enables to activating all controllers through Ninject in the assembly you have supplied .We are passing the current assembly as parameter for RegisterAllControllersIn() method. Now we can expose dependencies of controller constructors and properties to request injectionsStep 3 – Create Ninject ModulesWe can configure your dependency injection mapping information using Ninject Modules.Modules just need to implement the INinjectModule interface, but most should extend the NinjectModule class for simplicity. internal class ServiceModule : NinjectModule { public override void Load() { Bind<IFormsAuthentication>().To<FormsAuthenticationService>(); Bind<IMembershipService>().To<AccountMembershipService>(); Bind<MembershipProvider>().ToConstant(Membership.Provider); Bind<IDinnerRepository>().To<DinnerRepository>(); } } The above Binding inforamtion specified in the Load method tells the Ninject container that, to inject instance of DinnerRepositiry when there is a request for IDinnerRepositiry and inject instance of FormsAuthenticationService when there is a request for IFormsAuthentication and inject instance of AccountMembershipService when there is a request for IMembershipService. The AccountMembershipService class has a dependency with ASP.NET Membership provider. So we configure that inject the instance of Membership Provider. When configuring the binding information, you can specify the object scope in you application.There are four built-in scopes available in Ninject:Transient - A new instance of the type will be created each time one is requested. (This is the default scope). Binding method is .InTransientScope() Singleton - Only a single instance of the type will be created, and the same instance will be returned for each subsequent request. Binding method is .InSingletonScope()Thread - One instance of the type will be created per thread. Binding method is .InThreadScope() Request - One instance of the type will be created per web request, and will be destroyed when the request ends. Binding method is .InRequestScope() Step 4 – Configure the Ninject KernelOnce you create NinjectModule, you load them into a container called the kernel. To request an instance of a type from Ninject, you call the Get() extension method. We can configure the kernel, through the CreateKernel method in the Global.asax.cs. protected override IKernel CreateKernel() { var modules = new INinjectModule[] { new ServiceModule() }; return new StandardKernel(modules); } Here we are loading the Ninject Module (ServiceModule class created in the step 3) onto the container called the kernel for performing dependency injection.Source CodeYou can download the source code from http://nerddinneraddons.codeplex.com. I just put the modified source code onto CodePlex repository. The repository will update with more add-ons for the NerdDinner application.

Read the article

Generating a twitter OAuth access key - the semi-manual way

- by Piet

[UPDATE] Apparently someone at Twitter was listening, or I’m going senile/blind. Let’s call it a combination of both. Instead of following all the steps below, you could just login with the Twitter account you want to use on http://dev.twitter.com, register your application and then click ‘Edit Details’ on the application overview page at http://dev.twitter.com/apps. Next click the ‘Application detail’ button on the right, followed by the ‘My Access Token’ button in order to get your Access Token and Access Token Secret. This makes the old post below rather obsolete. Clearly a case of me thinking everything is a nail and ruby is a hammer (don’t they usually say this about java coders?) [ORIGINAL POST] OAuth is great! OAuth allows your application to use your user’s data without the need to ask for their password. So Twitter made the API much safer for their and your users. Hurray! Free pizza for everyone! Unless of course you’re using the Twitter API for your own needs like running your own bot and don’t need access to other user’s data. In such cases a simple username/password combination is more than enough. I can understand however that the Twitter guys don’t really care that much about these exceptions(?). Most such uses for the API are probably rather spammy in nature. !!! If you have a twitter app that uses the API to access external user’s data: look for another solution. This solution is ONLY meant when you ONLY need access to your own account(s) through the API. Other Solutions Mr Dallas Devries posted a solution here which involves requesting and scraping a one-time PIN. But: I like to minimize the amount of calls I make to twitter’s API or pages to lessen my chances of meeting the fail whale. Also, as soon as the pin isn’t included in a div called ‘oauth_pin’ anymore, this will fail. However, mr Devries’ post was a starting point for my solution, so I’m much obliged to him posting his findings. Authenticating with the Twitter API: old vs new Acessing The Twitter API the old way: require ‘twitter’ httpauth = Twitter::HTTPAuth.new('my_account','my_secret_password') client = Twitter::Base.new(httpauth) client.update(‘Hurray!’) The OAuth way: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Hurray!’) In the above case, ve4whatafuzzksaMQKjoI is the ‘consumer key’ (sometimes also referred to as ‘consumer token’) and KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY is the ‘consumer secret’. You’ll get these from Twitter when you register your app. 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the ‘access token’ and fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the ‘access secret’. This combination gives the registered application access to your account. I’ll show you how to obtain these by following the steps below. (Basically you’ll need a bunch of keys and you’ll have to jump a bit through hoops to obtain them for your server/bot. ) How to get these keys 1. Surf to the twitter apps registration page go to http://dev.twitter.com/apps to register your app. Login with your twitter account. 2. Register your application Enter something for Application name, Description, website,… as I said: they make you jump through hoops. If you plan on using the API to post tweets, Your application name and website will be used in the ‘5 minutes ago via…’ line below your tweet. You could use the this to point to a page with info about your bot, or maybe it’s useful for SEO purposes. For application type I choose ‘browser’ and entered http://www.hadermann.be/callback as a ‘Callback URL’. This url returns a 404 error, which is ideal because after giving our account access to our ‘application’ (step 6), it will redirect to this url with an ‘oauth_token’ and ‘oauth_verifier’ in the url. We need to get these from the url. It doesn’t really matter what you enter here though, you could leave it blank because you need to explicitely specify it when generating a request token. You probably want read&write access so set this at ‘Default Access type’. 3. Get your consumer key and consumer secret On the next page, copy/paste your ‘consumer key’ and ‘consumer secret’. You’ll need these later on. You also need these as part of the authentication in your script later on: oauth = Twitter::OAuth.new([consumer key], [consumer secret]) 4. Obtain your request token run the following in IRB to obtain your ‘request token’ Replace my fake consumer key and consumer secret with the one you obtained in step 3. And use something else instead http://www.hadermann.be/callback: although this will only give a 404, you shouldn’t trust me. irb(main):001:0> require 'oauth' irb(main):002:0> c = OAuth::Consumer.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY', {:site => 'http://twitter.com'}) irb(main):003:0> request_token = c.get_request_token(:oauth_callback => 'http://www.hadermann.be/callback') irb(main):004:0> request_token.token => "UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1" This (UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1) is the request token: Copy/paste this token, you will need this next. 5. Authorize your application surf to https://api.twitter.com/oauth/authorize?oauth_token=[the above token], for example: https://api.twitter.com/oauth/authorize?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1 This will bring you to the ‘An application would like to connect to your account’- screen on Twitter where you can grant access to the app you just registered. If you aren’t still logged in, you need to login first. Click ‘Allow’. Unless you don’t trust yourself. 6. Get your oauth_verifier from the redirected url Your browser will be redirected to your callback url, with an oauth_token and oauth_verifier parameter appended. You’ll need the oauth_verifier. In my case the browser redirected to: http://www.hadermann.be/callback?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1&oauth_verifier=waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag Which returned a 404, giving me the chance to copy/paste my oauth_verifier: waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag 7. Request an access token Back to irb, use the oauth_verifier to request an access token, as follows: irb(main):005:0> at = request_token.get_access_token(:oauth_verifier => 'waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag') irb(main):006:0> at.params[:oauth_token] => "123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis" irb(main):007:0> at.params[:oauth_token_secret] => "fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh" We’re there! 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the access token. fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the access secret. Try it! Try the following to post an update: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Cowabunga!’) Now you can go to your twitter page and delete the tweet if you want to.

Read the article

Adding DTrace Probes to PHP Extensions

- by cj

The powerful DTrace tracing facility has some PHP-specific probes that can be enabled with --enable-dtrace. DTrace for Linux is being created by Oracle and is currently in tech preview. Currently it doesn't support userspace tracing so, in the meantime, Systemtap can be used to monitor the probes implemented in PHP. This was recently outlined in David Soria Parra's post Probing PHP with Systemtap on Linux. My post shows how DTrace probes can be added to PHP extensions and traced on Linux. I was using Oracle Linux 6.3. Not all Linux kernels are built with Systemtap, since this can impact stability. Check whether your running kernel (or others installed) have Systemtap enabled, and reboot with such a kernel: # grep CONFIG_UTRACE /boot/config-`uname -r` # grep CONFIG_UTRACE /boot/config-* When you install Systemtap itself, the package systemtap-sdt-devel is needed since it provides the sdt.h header file: # yum install systemtap-sdt-devel You can now install and build PHP as shown in David's article. Basically the build is with: $ cd ~/php-src $ ./configure --disable-all --enable-dtrace $ make (For me, running 'make' a second time failed with an error. The workaround is to do 'git checkout Zend/zend_dtrace.d' and then rerun 'make'. See PHP Bug 63704) David's article shows how to trace the probes already implemented in PHP. You can also use Systemtap to trace things like userspace PHP function calls. For example, create test.php: <?php $c = oci_connect('hr', 'welcome', 'localhost/orcl'); $s = oci_parse($c, "select dbms_xmlgen.getxml('select * from dual') xml from dual"); $r = oci_execute($s); $row = oci_fetch_array($s, OCI_NUM); $x = $row[0]->load(); $row[0]->free(); echo $x; ?> The normal output of this file is the XML form of Oracle's DUAL table: $ ./sapi/cli/php ~/test.php <?xml version="1.0"?> <ROWSET> <ROW> <DUMMY>X</DUMMY> </ROW> </ROWSET> To trace the PHP function calls, create the tracing file functrace.stp: probe process("sapi/cli/php").function("zif_*") { printf("Started function %s\n", probefunc()); } probe process("sapi/cli/php").function("zif_*").return { printf("Ended function %s\n", probefunc()); } This makes use of the way PHP userspace functions (not builtins) like oci_connect() map to C functions with a "zif_" prefix. Login as root, and run System tap on the PHP script: # cd ~cjones/php-src # stap -c 'sapi/cli/php ~cjones/test.php' ~cjones/functrace.stp Started function zif_oci_connect Ended function zif_oci_connect Started function zif_oci_parse Ended function zif_oci_parse Started function zif_oci_execute Ended function zif_oci_execute Started function zif_oci_fetch_array Ended function zif_oci_fetch_array Started function zif_oci_lob_load <?xml version="1.0"?> <ROWSET> <ROW> <DUMMY>X</DUMMY> </ROW> </ROWSET> Ended function zif_oci_lob_load Started function zif_oci_free_descriptor Ended function zif_oci_free_descriptor Each call and return is logged. The Systemtap scripting language allows complex scripts to be built. There are many examples on the web. To augment this generic capability and the PHP probes in PHP, other extensions can have probes too. Below are the steps I used to add probes to OCI8: I created a provider file ext/oci8/oci8_dtrace.d, enabling three probes. The first one will accept a parameter that runtime tracing can later display: provider php { probe oci8__connect(char *username); probe oci8__nls_start(); probe oci8__nls_done(); }; I updated ext/oci8/config.m4 with the PHP_INIT_DTRACE macro. The patch is at the end of config.m4. The macro takes the provider prototype file, a name of the header file that 'dtrace' will generate, and a list of sources files with probes. When --enable-dtrace is used during PHP configuration, then the outer $PHP_DTRACE check is true and my new probes will be enabled. I've chosen to define an OCI8 specific macro, HAVE_OCI8_DTRACE, which can be used in the OCI8 source code: diff --git a/ext/oci8/config.m4 b/ext/oci8/config.m4 index 34ae76c..f3e583d 100644 --- a/ext/oci8/config.m4 +++ b/ext/oci8/config.m4 @@ -341,4 +341,17 @@ if test "$PHP_OCI8" != "no"; then PHP_SUBST_OLD(OCI8_ORACLE_VERSION) fi + + if test "$PHP_DTRACE" = "yes"; then + AC_CHECK_HEADERS([sys/sdt.h], [ + PHP_INIT_DTRACE([ext/oci8/oci8_dtrace.d], + [ext/oci8/oci8_dtrace_gen.h],[ext/oci8/oci8.c]) + AC_DEFINE(HAVE_OCI8_DTRACE,1, + [Whether to enable DTrace support for OCI8 ]) + ], [ + AC_MSG_ERROR( + [Cannot find sys/sdt.h which is required for DTrace support]) + ]) + fi + fi In ext/oci8/oci8.c, I added the probes at, for this example, semi-arbitrary places: diff --git a/ext/oci8/oci8.c b/ext/oci8/oci8.c index e2241cf..ffa0168 100644 --- a/ext/oci8/oci8.c +++ b/ext/oci8/oci8.c @@ -1811,6 +1811,12 @@ php_oci_connection *php_oci_do_connect_ex(char *username, int username_len, char } } +#ifdef HAVE_OCI8_DTRACE + if (DTRACE_OCI8_CONNECT_ENABLED()) { + DTRACE_OCI8_CONNECT(username); + } +#endif + /* Initialize global handles if they weren't initialized before */ if (OCI_G(env) == NULL) { php_oci_init_global_handles(TSRMLS_C); @@ -1870,11 +1876,22 @@ php_oci_connection *php_oci_do_connect_ex(char *username, int username_len, char size_t rsize = 0; sword result; +#ifdef HAVE_OCI8_DTRACE + if (DTRACE_OCI8_NLS_START_ENABLED()) { + DTRACE_OCI8_NLS_START(); + } +#endif PHP_OCI_CALL_RETURN(result, OCINlsEnvironmentVariableGet, (&charsetid_nls_lang, 0, OCI_NLS_CHARSET_ID, 0, &rsize)); if (result != OCI_SUCCESS) { charsetid_nls_lang = 0; } smart_str_append_unsigned_ex(&hashed_details, charsetid_nls_lang, 0); + +#ifdef HAVE_OCI8_DTRACE + if (DTRACE_OCI8_NLS_DONE_ENABLED()) { + DTRACE_OCI8_NLS_DONE(); + } +#endif } timestamp = time(NULL); The oci_connect(), oci_pconnect() and oci_new_connect() calls all use php_oci_do_connect_ex() internally. The first probe simply records that the PHP application made a connection call. I already showed a way to do this without needing a probe, but adding a specific probe lets me record the username. The other two probes can be used to time how long the globalization initialization takes. The relationships between the oci8_dtrace.d names like oci8__connect, the probe guards like DTRACE_OCI8_CONNECT_ENABLED() and probe names like DTRACE_OCI8_CONNECT() are obvious after seeing the pattern of all three probes. I included the new header that will be automatically created by the dtrace tool when PHP is built. I did this in ext/oci8/php_oci8_int.h: diff --git a/ext/oci8/php_oci8_int.h b/ext/oci8/php_oci8_int.h index b0d6516..c81fc5a 100644 --- a/ext/oci8/php_oci8_int.h +++ b/ext/oci8/php_oci8_int.h @@ -44,6 +44,10 @@ # endif # endif /* osf alpha */ +#ifdef HAVE_OCI8_DTRACE +#include "oci8_dtrace_gen.h" +#endif + #if defined(min) #undef min #endif Now PHP can be rebuilt: $ cd ~/php-src $ rm configure && ./buildconf --force $ ./configure --disable-all --enable-dtrace \ --with-oci8=instantclient,/home/cjones/instantclient $ make If 'make' fails, do the 'git checkout Zend/zend_dtrace.d' trick I mentioned. The new probes can be seen by logging in as root and running: # stap -l 'process.provider("php").mark("oci8*")' -c 'sapi/cli/php -i' process("sapi/cli/php").provider("php").mark("oci8__connect") process("sapi/cli/php").provider("php").mark("oci8__nls_done") process("sapi/cli/php").provider("php").mark("oci8__nls_start") To test them out, create a new trace file, oci.stp: global numconnects; global start; global numcharlookups = 0; global tottime = 0; probe process.provider("php").mark("oci8-connect") { printf("Connected as %s\n", user_string($arg1)); numconnects += 1; } probe process.provider("php").mark("oci8-nls_start") { start = gettimeofday_us(); numcharlookups++; } probe process.provider("php").mark("oci8-nls_done") { tottime += gettimeofday_us() - start; } probe end { printf("Connects: %d, Charset lookups: %ld\n", numconnects, numcharlookups); printf("Total NLS charset initalization time: %ld usecs/connect\n", (numcharlookups 0 ? tottime/numcharlookups : 0)); } This calculates the average time that the NLS character set lookup takes. It also prints out the username of each connection, as an example of using parameters. Login as root and run Systemtap over the PHP script: # cd ~cjones/php-src # stap -c 'sapi/cli/php ~cjones/test.php' ~cjones/oci.stp Connected as cj <?xml version="1.0"?> <ROWSET> <ROW> <DUMMY>X</DUMMY> </ROW> </ROWSET> Connects: 1, Charset lookups: 1 Total NLS charset initalization time: 164 usecs/connect This shows the time penalty of making OCI8 look up the default character set. This time would be zero if a character set had been passed as the fourth argument to oci_connect() in test.php.

Read the article

MvcExtensions – Bootstrapping

- by kazimanzurrashid

When you create a new ASP.NET MVC application you will find that the global.asax contains the following lines: namespace MvcApplication1 { // Note: For instructions on enabling IIS6 or IIS7 classic mode, // visit http://go.microsoft.com/?LinkId=9394801 public class MvcApplication : System.Web.HttpApplication { public static void RegisterRoutes(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "Index", id = UrlParameter.Optional } // Parameter defaults ); } protected void Application_Start() { AreaRegistration.RegisterAllAreas(); RegisterRoutes(RouteTable.Routes); } } } As the application grows, there are quite a lot of plumbing code gets into the global.asax which quickly becomes a design smell. Lets take a quick look at the code of one of the open source project that I recently visited: public static void RegisterRoutes(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.MapRoute("Default","{controller}/{action}/{id}", new { controller = "Home", action = "Index", id = "" }); } protected override void OnApplicationStarted() { Error += OnError; EndRequest += OnEndRequest; var settings = new SparkSettings() .AddNamespace("System") .AddNamespace("System.Collections.Generic") .AddNamespace("System.Web.Mvc") .AddNamespace("System.Web.Mvc.Html") .AddNamespace("MvcContrib.FluentHtml") .AddNamespace("********") .AddNamespace("********.Web") .SetPageBaseType("ApplicationViewPage") .SetAutomaticEncoding(true); #if DEBUG settings.SetDebug(true); #endif var viewFactory = new SparkViewFactory(settings); ViewEngines.Engines.Add(viewFactory); #if !DEBUG PrecompileViews(viewFactory); #endif RegisterAllControllersIn("********.Web"); log4net.Config.XmlConfigurator.Configure(); RegisterRoutes(RouteTable.Routes); Factory.Load(new Components.WebDependencies()); ModelBinders.Binders.DefaultBinder = new Binders.GenericBinderResolver(Factory.TryGet<IModelBinder>); ValidatorConfiguration.Initialize("********"); HtmlValidationExtensions.Initialize(ValidatorConfiguration.Rules); } private void OnEndRequest(object sender, System.EventArgs e) { if (((HttpApplication)sender).Context.Handler is MvcHandler) { CreateKernel().Get<ISessionSource>().Close(); } } private void OnError(object sender, System.EventArgs e) { CreateKernel().Get<ISessionSource>().Close(); } protected override IKernel CreateKernel() { return Factory.Kernel; } private static void PrecompileViews(SparkViewFactory viewFactory) { var batch = new SparkBatchDescriptor(); batch.For<HomeController>().For<ManageController>(); viewFactory.Precompile(batch); } As you can see there are quite a few of things going on in the above code, Registering the ViewEngine, Compiling the Views, Registering the Routes/Controllers/Model Binders, Settings up Logger, Validations and as you can imagine the more it becomes complex the more things will get added in the application start. One of the goal of the MVCExtensions is to reduce the above design smell. Instead of writing all the plumbing code in the application start, it contains BootstrapperTask to register individual services. Out of the box, it contains BootstrapperTask to register Controllers, Controller Factory, Action Invoker, Action Filters, Model Binders, Model Metadata/Validation Providers, ValueProvideraFactory, ViewEngines etc and it is intelligent enough to automatically detect the above types and register into the ASP.NET MVC Framework. Other than the built-in tasks you can create your own custom task which will be automatically executed when the application starts. When the BootstrapperTasks are in action you will find the global.asax pretty much clean like the following: public class MvcApplication : UnityMvcApplication { public void ErrorLog_Filtering(object sender, ExceptionFilterEventArgs e) { Check.Argument.IsNotNull(e, "e"); HttpException exception = e.Exception.GetBaseException() as HttpException; if ((exception != null) && (exception.GetHttpCode() == (int)HttpStatusCode.NotFound)) { e.Dismiss(); } } } The above code is taken from my another open source project Shrinkr, as you can see the global.asax is longer cluttered with any plumbing code. One special thing you have noticed that it is inherited from the UnityMvcApplication rather than regular HttpApplication. There are separate version of this class for each IoC Container like NinjectMvcApplication, StructureMapMvcApplication etc. Other than executing the built-in tasks, the Shrinkr also has few custom tasks which gets executed when the application starts. For example, when the application starts, we want to ensure that the default users (which is specified in the web.config) are created. The following is the custom task that is used to create those default users: public class CreateDefaultUsers : BootstrapperTask { protected override TaskContinuation ExecuteCore(IServiceLocator serviceLocator) { IUserRepository userRepository = serviceLocator.GetInstance<IUserRepository>(); IUnitOfWork unitOfWork = serviceLocator.GetInstance<IUnitOfWork>(); IEnumerable<User> users = serviceLocator.GetInstance<Settings>().DefaultUsers; bool shouldCommit = false; foreach (User user in users) { if (userRepository.GetByName(user.Name) == null) { user.AllowApiAccess(ApiSetting.InfiniteLimit); userRepository.Add(user); shouldCommit = true; } } if (shouldCommit) { unitOfWork.Commit(); } return TaskContinuation.Continue; } } There are several other Tasks in the Shrinkr that we are also using which you will find in that project. To create a custom bootstrapping task you have create a new class which either implements the IBootstrapperTask interface or inherits from the abstract BootstrapperTask class, I would recommend to start with the BootstrapperTask as it already has the required code that you have to write in case if you choose the IBootstrapperTask interface. As you can see in the above code we are overriding the ExecuteCore to create the default users, the MVCExtensions is responsible for populating the ServiceLocator prior calling this method and in this method we are using the service locator to get the dependencies that are required to create the users (I will cover the custom dependencies registration in the next post). Once the users are created, we are returning a special enum, TaskContinuation as the return value, the TaskContinuation can have three values Continue (default), Skip and Break. The reason behind of having this enum is, in some special cases you might want to skip the next task in the chain or break the complete chain depending upon the currently running task, in those cases you will use the other two values instead of the Continue. The last thing I want to cover in the bootstrapping task is the Order. By default all the built-in tasks as well as newly created task order is set to the DefaultOrder(a static property), in some special cases you might want to execute it before/after all the other tasks, in those cases you will assign the Order in the Task constructor. For Example, in Shrinkr, we want to run few background services when the all the tasks are executed, so we assigned the order as DefaultOrder + 1. Here is the code of that Task: public class ConfigureBackgroundServices : BootstrapperTask { private IEnumerable<IBackgroundService> backgroundServices; public ConfigureBackgroundServices() { Order = DefaultOrder + 1; } protected override TaskContinuation ExecuteCore(IServiceLocator serviceLocator) { backgroundServices = serviceLocator.GetAllInstances<IBackgroundService>().ToList(); backgroundServices.Each(service => service.Start()); return TaskContinuation.Continue; } protected override void DisposeCore() { backgroundServices.Each(service => service.Stop()); } } That’s it for today, in the next post I will cover the custom service registration, so stay tuned.

Read the article

Solaris 10 branded zone VM Templates for Solaris 11 on OTN

- by jsavit

Early this year I wrote the article Ours Goes To 11 which describes the ability to import Solaris 10 systems into a "Solaris 10 branded zone" under Oracle Solaris 11. I did this using Solaris 11 Express, and the capability remains in Solaris 11 with only slight changes. This important tool lets you painlessly inhaling a Solaris Container from Solaris 10 or entire Solaris 10 systems ("the global zone") into virtualized environments on a Solaris 11 OS. Just recently, Oracle provided Oracle VM Templates for Oracle Solaris 10 Zones to let you create Solaris 10 branded zones for Solaris 11 even if you don't currently have access to install media or a running Solaris 10 system. To use this, just download the Oracle VM Template for Oracle Solaris Zone 10 from OTN at http://www.oracle.com/technetwork/server-storage/solaris11/downloads/virtual-machines-1355605.html. This page contains images of Oracle Solaris 10 8/11 (the recent update to Solaris 10) in SPARC and x86 formats suitable for creating branded zones. The same page also has a VirtualBox image you can download for a complete Solaris 10 install in a guest virtual machine you can run on any host OS that supports VirtualBox. Both sets of downloads provide a quick - and extremely easy - way to set up a virtual Solaris 10 environment. In the case of the Oracle VM Templates, they illustrate several advanced features of Solaris 11. To start, just go to the above link, download the template for the hardware platform (SPARC or x86) you want, and download the README file also linked from that page. Install prerequisites The README file tells you to install the prerequisite Solaris 11 package that implements the Solaris 10 brand. Then you can install instances of zones with that brand. # pkg install pkg:/system/zones/brand/brand-solaris10 Packages to install: 1 Create boot environment: No Create backup boot environment: Yes DOWNLOAD PKGS FILES XFER (MB) Completed 1/1 44/44 0.4/0.4 PHASE ACTIONS Install Phase 74/74 PHASE ITEMS Package State Update Phase 1/1 Image State Update Phase 2/2 That took only a few minutes, and didn't require a reboot. Install the Solaris 10 zone Now it's time to run the downloaded template file. First make it executable via the chmod command, of course. I found that (unlike stated in the README) there was no need to rename the downloaded file to remove the .bin. When you run it you provide several parameters to describe the zone configuration: -a IP address - the IP address and optional netmask for the zone. This is the only mandatory parameter. -z zonename - the name of the zone you would like to create. -i interface - the package will create an exclusive-IP zone using a virtual NIC (vnic) based on this physical interface. In my case, I have a NIC called rge0. -p PATH - specifies the path in which you want the zoneroot to be placed. In my case, I have a ZFS dataset mounted at /zones, and this will create a zoneroot at /zones/s10u10. Kicking it off, you will see a copyright message, and then messages showing progress building the zone, which only takes a few minutes. # ./solaris-10u10-x86.bin -p /zones -a 192.168.1.100 -i rge0 -z s10u10 ... ... Checking disk-space for extraction Ok Extracting in /export/home/CDimages/s10zone/bootimage.ihaqvh ... 100% [===============================] Checking data integrity Ok Checking platform compatibility The host and the image do not have the same Solaris release: host Solaris release: 5.11 image Solaris release: 5.10 Will create a Solaris 10 branded zone. Warning: could not find a defaultrouter Zone won't have any defaultrouter configured IMAGE: ./solaris-10u10-x86.bin ZONE: s10u10 ZONEPATH: /zones/s10u10 INTERFACE: rge0 VNIC: vnicZBI13379 MAC ADDR: 2:8:20:5c:1a:cc IP ADDR: 192.168.1.100 NETMASK: 255.255.255.0 DEFROUTER: NONE TIMEZONE: US/Arizona Checking disk-space for installation Ok Installing in /zones/s10u10 ... 100% [===============================] Using a static exclusive-IP Attaching s10u10 Booting s10u10 Waiting for boot to complete booting... booting... booting... Zone s10u10 booted The zone's root password has been set using the root password of the local host. You can change the zone's root password to further harden the security of the zone: being root, log into the zone from the local host with the command 'zlogin s10u10'. Once logged in, change the root password with the command 'passwd'. The nifty part in my opinion (besides being so easy), is that the zone was created as an exclusive-IP zone on a virtual NIC. This network configuration lets you enforce traffic isolation from other zones, enforce network Quality of Service, and even let the zone set its own characteristics like IP address and packet size. Independence of the zone's network characteristics from the global zone is one of the enhancements in Solaris 10 that make it easier to consolidate zones while preserving their autonomy, yet provide control in a consolidated environment. Let's see what the virtual network environment looks like by issuing commands from the Solaris 11 global zone. First I'll use Old School ifconfig, and then I'll use the new ipadm and dladm commands. # ifconfig -a4 lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 rge0: flags=1004943<UP,BROADCAST,RUNNING,PROMISC,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet 192.168.1.3 netmask ffffff00 broadcast 192.168.1.255 ether 0:14:d1:18:ac:bc vboxnet0: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 3 inet 192.168.56.1 netmask ffffff00 broadcast 192.168.56.255 ether 8:0:27:f8:62:1c # dladm show-phys LINK MEDIA STATE SPEED DUPLEX DEVICE yge0 Ethernet unknown 0 unknown yge0 yge1 Ethernet unknown 0 unknown yge1 rge0 Ethernet up 1000 full rge0 vboxnet0 Ethernet up 1000 full vboxnet0 # dladm show-link LINK CLASS MTU STATE OVER yge0 phys 1500 unknown -- yge1 phys 1500 unknown -- rge0 phys 1500 up -- vboxnet0 phys 1500 up -- vnicZBI13379 vnic 1500 up rge0 s10u10/vnicZBI13379 vnic 1500 up rge0 s10u10/net0 vnic 1500 up rge0 # dladm show-vnic LINK OVER SPEED MACADDRESS MACADDRTYPE VID vnicZBI13379 rge0 1000 2:8:20:5c:1a:cc random 0 s10u10/vnicZBI13379 rge0 1000 2:8:20:5c:1a:cc random 0 s10u10/net0 rge0 1000 2:8:20:9d:d0:79 random 0 # ipadm show-addr ADDROBJ TYPE STATE ADDR lo0/v4 static ok 127.0.0.1/8 rge0/_a dhcp ok 192.168.1.3/24 vboxnet0/_a static ok 192.168.56.1/24 lo0/v6 static ok ::1/128 Log into the zone The install step already booted the zone, so lets log into it. Notice how you have to be appropriately privileged to log into a zone. This is my home system so I'm being a bit cavalier, but in a production environment you can give granular control of who can login to which zones. Voila! a Solaris 10 environment under a Solaris 11 kernel. Notice the output from the uname -a and ifconfig commands, and output from a ping to a nearby host. $ zlogin s10u10 zlogin: You lack sufficient privilege to run this command (all privs required) savit@home:~$ sudo zlogin s10u10 Password: [Connected to zone 's10u10' pts/5] Oracle Corporation SunOS 5.10 Generic Patch January 2005 # uname -a SunOS s10u10 5.10 Generic_Virtual i86pc i386 i86pc # ifconfig -a4 lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vnicZBI13379: flags=1000843 mtu 1500 index 2 inet 192.168.1.100 netmask ffffff00 broadcast 192.168.1.255 ether 2:8:20:5c:1a:cc # bash bash-3.2# ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vnicZBI13379: flags=1000843 mtu 1500 index 2 inet 192.168.1.100 netmask ffffff00 broadcast 192.168.1.255 ether 2:8:20:5c:1a:cc bash-3.2# ping 192.168.1.2 192.168.1.2 is alive For fun, I configured Apache (setting its configuration file in /etc/apache2) and brought it up. Easy - took just a few minutes. bash-3.2# svcs apache2 STATE STIME FMRI disabled 12:38:46 svc:/network/http:apache2 bash-3.2# svcadm enable apache2 Summary In just a few minutes, I built a functioning virtual Solaris 10 environment under by Solaris 11 system. It was... easy! While I can still do it the manual way (creating and using a system archive), this is a low-effort way to create a Solaris 10 zone on Solaris 11.

Read the article

Soapi.CS : A fully relational fluent .NET Stack Exchange API client library

- by Sky Sanders

Soapi.CS for .Net / Silverlight / Windows Phone 7 / Mono as easy as breathing...: var context = new ApiContext(apiKey).Initialize(false); Question thisPost = context.Official .StackApps .Questions.ById(386) .WithComments(true) .First(); Console.WriteLine(thisPost.Title); thisPost .Owner .Questions .PageSize(5) .Sort(PostSort.Votes) .ToList() .ForEach(q=> { Console.WriteLine("\t" + q.Score + "\t" + q.Title); q.Timeline.ToList().ForEach(t=> Console.WriteLine("\t\t" + t.TimelineType + "\t" + t.Owner.DisplayName)); Console.WriteLine(); }); // if you can think it, you can get it. Output Soapi.CS : A fully relational fluent .NET Stack Exchange API client library 21 Soapi.CS : A fully relational fluent .NET Stack Exchange API client library Revision code poet Revision code poet Votes code poet Votes code poet Revision code poet Revision code poet Revision code poet Votes code poet Votes code poet Votes code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Revision code poet Votes code poet Comment code poet Revision code poet Votes code poet Revision code poet Revision code poet Revision code poet Answer code poet Revision code poet Revision code poet 14 SOAPI-WATCH: A realtime service that notifies subscribers via twitter when the API changes in any way. Votes code poet Revision code poet Votes code poet Comment code poet Comment code poet Comment code poet Votes lfoust Votes code poet Comment code poet Comment code poet Comment code poet Comment code poet Revision code poet Comment lfoust Votes code poet Revision code poet Votes code poet Votes lfoust Votes code poet Revision code poet Comment Dave DeLong Revision code poet Revision code poet Votes code poet Comment lfoust Comment Dave DeLong Comment lfoust Comment lfoust Comment Dave DeLong Revision code poet 11 SOAPI-EXPLORE: Self-updating single page JavaSript API test harness Votes code poet Votes code poet Votes code poet Votes code poet Votes code poet Comment code poet Revision code poet Votes code poet Revision code poet Revision code poet Revision code poet Comment code poet Revision code poet Votes code poet Comment code poet Question code poet Votes code poet 11 Soapi.JS V1.0: fluent JavaScript wrapper for the StackOverflow API Comment George Edison Comment George Edison Comment George Edison Comment George Edison Comment George Edison Comment George Edison Answer George Edison Votes code poet Votes code poet Votes code poet Votes code poet Revision code poet Revision code poet Answer code poet Comment code poet Revision code poet Comment code poet Comment code poet Comment code poet Revision code poet Revision code poet Votes code poet Votes code poet Votes code poet Votes code poet Comment code poet Comment code poet Comment code poet Comment code poet Comment code poet 9 SOAPI-DIFF: Your app broke? Check SOAPI-DIFF to find out what changed in the API Votes code poet Revision code poet Comment Dennis Williamson Answer Dennis Williamson Votes code poet Votes Dennis Williamson Comment code poet Question code poet Votes code poet About A robust, fully relational, easy to use, strongly typed, end-to-end StackOverflow API Client Library. Out of the box, Soapi provides you with a robust client library that abstracts away most all of the messy details of consuming the API and lets you concentrate on implementing your ideas. A few features include: A fully relational model of the API data set exposed via a fully 'dot navigable' IEnumerable (LINQ) implementation. Simply tell Soapi what you want and it will get it for you. e.g. "On my first question, from the author of the first comment, get the first page of comments by that person on any post" my.Questions.First().Comments.First().Owner.Comments.ToList(); (yes this is a real expression that returns the data as expressed!) Full coverage of the API, all routes and all parameters with an intuitive syntax. Strongly typed Domain Data Objects for all API data structures. Eager and Lazy Loading of 'stub' objects. Eager\Lazy loading may be disabled. When finer grained control of requests is desired, the core RouteMap objects may be leveraged to request data from any of the API paths using all available parameters as documented on the help pages. A rich Asynchronous implementation. A configurable request cache to reduce unnecessary network traffic and to simplify your usage logic. There is no need to go out of your way to be frugal. You may set a distinct cache duration for any particular route. A configurable request throttle to ensure compliance with the api terms of usage and to simplify your code in that you do not have to worry about and respond to 50X errors. The RequestCache and Throttled Queue are thread-safe, so can make as many requests as you like from as many threads as you like as fast as you like and not worry about abusing the api or having to write reams of management/compensation code. Configurable retry threshold that will, by default, make up to 3 attempts to retrieve a request before failing. Every request made by Soapi is properly formed and directed so most any http error will be the result of a timeout or other network infrastructure. A retry buffer provides a level of fault tolerance that you can rely on. An almost identical javascript library, Soapi.JS, and it's full figured big brother, Soapi.JS2, that will enable you to leverage your server cycles and bandwidth for only those tasks that require it and offload things like status updates to the client's browser. License Licensed GPL Version 2 license. Why is Soapi.CS GPL? Can I get an LGPL license for Soapi.CS? (hint: probably) Platforms .NET 3.5 .NET 4.0 Silverlight 3 Silverlight 4 Windows Phone 7 Mono Download Source code lives @ http://soapics.codeplex.com. Binary releases are forthcoming. codeplex is acting up again. get the source and binaries @ http://bitbucket.org/bitpusher/soapi.cs/downloads The source is C# 3.5. and includes projects and solutions for the following IDEs Visual Studio 2008 Visual Studio 2010 ModoDevelop 2.4 Documentation Full documentation is available at http://soapi.info/help/cs/index.aspx Sample Code / Usage Examples Sample code and usage examples will be added as answers to this question. Full API Coverage all API routes are covered Full Parameter Parity If the API exposes it, Soapi giftwraps it for you. Building a simple app with Soapi.CS - a simple app that gathers all traces of a user in the whole stackiverse. Fluent Configuration - Setting up a Soapi.ApiContext could not be easier Bulk Data Import - A tiny app that quickly loads a SQLite data file with all users in the stackiverse. Paged Results - Soapi.CS transparently handles multi-page operations. Asynchronous Requests - Soapi.CS provides a rich asynchronous model that is especially useful when writing api apps in Silverlight or Windows Phone 7. Caching and Throttling - how and why Apps that use Soapi.CS Soapi.FindUser - .net utility for locating a user anywhere in the stackiverse Soapi.Explore - The entire API at your command Soapi.LastSeen - List users by last access time Add your app/site here - I know you are out there ;-) if you are not comfortable editing this post, simply add a comment and I will add it. The CS/SL/WP7/MONO libraries all compile the same code and with the exception of environmental considerations of Silverlight, the code samples are valid for all libraries. You may also find guidance in the test suites. More information on the SOAPI eco-system. Contact This library is currently the effort of me, Sky Sanders (code poet) and can be reached at gmail - sky.sanders Any who are interested in improving this library are welcome. Support Soapi You can help support this project by voting for Soapi's Open Source Ad post For more information about the origins of Soapi.CS and the rest of the Soapi eco-system see What is Soapi and why should I care?

Read the article

Maintaining shared service in ASP.NET MVC Application

- by kazimanzurrashid

Depending on the application sometimes we have to maintain some shared service throughout our application. Let’s say you are developing a multi-blog supported blog engine where both the controller and view must know the currently visiting blog, it’s setting , user information and url generation service. In this post, I will show you how you can handle this kind of case in most convenient way. First, let see the most basic way, we can create our PostController in the following way: public class PostController : Controller { public PostController(dependencies...) { } public ActionResult Index(string blogName, int? page) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublished(blog.Id, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetPublishedCount(blog.Id); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new IndexViewModel(urlResolver, user, blog, posts, count, page)); } public ActionResult Archive(string blogName, int? page, ArchiveDate archiveDate) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindArchived(blog.Id, archiveDate, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetArchivedCount(blog.Id, archiveDate); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new ArchiveViewModel(urlResolver, user, blog, posts, count, page, achiveDate)); } public ActionResult Tag(string blogName, string tagSlug, int? page) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } TagInfo tag = tagService.FindBySlug(blog.Id, tagSlug); if (tag == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublishedByTag(blog.Id, tag.Id, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetPublishedCountByTag(tag.Id); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new TagViewModel(urlResolver, user, blog, posts, count, page, tag)); } } As you can see the above code heavily depends upon the current blog and the blog retrieval code is duplicated in all of the action methods, once the blog is retrieved the same blog is passed in the view model. Other than the blog the view also needs the current user and url resolver to render it properly. One way to remove the duplicate blog retrieval code is to create a custom model binder which converts the blog from a blog name and use the blog a parameter in the action methods instead of the string blog name, but it only helps the first half in the above scenario, the action methods still have to pass the blog, user and url resolver etc in the view model. Now lets try to improve the the above code, first lets create a new class which would contain the shared services, lets name it as BlogContext: public class BlogContext { public BlogInfo Blog { get; set; } public UserInfo User { get; set; } public IUrlResolver UrlResolver { get; set; } } Next, we will create an interface, IContextAwareService: public interface IContextAwareService { BlogContext Context { get; set; } } The idea is, whoever needs these shared services needs to implement this interface, in our case both the controller and the view model, now we will create an action filter which will be responsible for populating the context: public class PopulateBlogContextAttribute : FilterAttribute, IActionFilter { private static string blogNameRouteParameter = "blogName"; private readonly IBlogService blogService; private readonly IUserService userService; private readonly BlogContext context; public PopulateBlogContextAttribute(IBlogService blogService, IUserService userService, IUrlResolver urlResolver) { Invariant.IsNotNull(blogService, "blogService"); Invariant.IsNotNull(userService, "userService"); Invariant.IsNotNull(urlResolver, "urlResolver"); this.blogService = blogService; this.userService = userService; context = new BlogContext { UrlResolver = urlResolver }; } public static string BlogNameRouteParameter { [DebuggerStepThrough] get { return blogNameRouteParameter; } [DebuggerStepThrough] set { blogNameRouteParameter = value; } } public void OnActionExecuting(ActionExecutingContext filterContext) { string blogName = (string) filterContext.Controller.ValueProvider.GetValue(BlogNameRouteParameter).ConvertTo(typeof(string), Culture.Current); if (!string.IsNullOrWhiteSpace(blogName)) { context.Blog = blogService.FindByName(blogName); } if (context.Blog == null) { filterContext.Result = new NotFoundResult(); return; } if (filterContext.HttpContext.User.Identity.IsAuthenticated) { context.User = userService.FindByName(filterContext.HttpContext.User.Identity.Name); } IContextAwareService controller = filterContext.Controller as IContextAwareService; if (controller != null) { controller.Context = context; } } public void OnActionExecuted(ActionExecutedContext filterContext) { Invariant.IsNotNull(filterContext, "filterContext"); if ((filterContext.Exception == null) || filterContext.ExceptionHandled) { IContextAwareService model = filterContext.Controller.ViewData.Model as IContextAwareService; if (model != null) { model.Context = context; } } } } As you can see we are populating the context in the OnActionExecuting, which executes just before the controllers action methods executes, so by the time our action methods executes the context is already populated, next we are are assigning the same context in the view model in OnActionExecuted method which executes just after we set the model and return the view in our action methods. Now, lets change the view models so that it implements this interface: public class IndexViewModel : IContextAwareService { // More Codes } public class ArchiveViewModel : IContextAwareService { // More Codes } public class TagViewModel : IContextAwareService { // More Codes } and the controller: public class PostController : Controller, IContextAwareService { public PostController(dependencies...) { } public BlogContext Context { get; set; } public ActionResult Index(int? page) { IEnumerable<PostInfo> posts = postService.FindPublished(Context.Blog.Id, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetPublishedCount(Context.Blog.Id); return View(new IndexViewModel(posts, count, page)); } public ActionResult Archive(int? page, ArchiveDate archiveDate) { IEnumerable<PostInfo> posts = postService.FindArchived(Context.Blog.Id, archiveDate, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetArchivedCount(Context.Blog.Id, archiveDate); return View(new ArchiveViewModel(posts, count, page, achiveDate)); } public ActionResult Tag(string blogName, string tagSlug, int? page) { TagInfo tag = tagService.FindBySlug(Context.Blog.Id, tagSlug); if (tag == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublishedByTag(Context.Blog.Id, tag.Id, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetPublishedCountByTag(tag.Id); return View(new TagViewModel(posts, count, page, tag)); } } Now, the last thing where we have to glue everything, I will be using the AspNetMvcExtensibility to register the action filter (as there is no better way to inject the dependencies in action filters). public class RegisterFilters : RegisterFiltersBase { private static readonly Type controllerType = typeof(Controller); private static readonly Type contextAwareType = typeof(IContextAwareService); protected override void Register(IFilterRegistry registry) { TypeCatalog controllers = new TypeCatalogBuilder() .Add(GetType().Assembly) .Include(type => controllerType.IsAssignableFrom(type) && contextAwareType.IsAssignableFrom(type)); registry.Register<PopulateBlogContextAttribute>(controllers); } } Thoughts and Comments?

Read the article

SQL Server and Hyper-V Dynamic Memory Part 3

- by SQLOS Team

In parts 1 and 2 of this series we looked at the basics of Hyper-V Dynamic Memory and SQL Server memory management. In this part Serdar looks at configuration guidelines for SQL Server memory management. Part 3: Configuration Guidelines for Hyper-V Dynamic Memory and SQL Server Now that we understand SQL Server Memory Management and Hyper-V Dynamic Memory basics, let’s take a look at general configuration guidelines in order to utilize benefits of Hyper-V Dynamic Memory in your SQL Server VMs. Requirements Host Operating System Requirements Hyper-V Dynamic Memory feature is introduced with Windows Server 2008 R2 SP1. Therefore in order to use Dynamic Memory for your virtual machines, you need to have Windows Server 2008 R2 SP1 or Microsoft Hyper-V Server 2008 R2 SP1 in your Hyper-V host. Guest Operating System Requirements In addition to this Dynamic Memory is only supported in Standard, Web, Enterprise and Datacenter editions of windows running inside VMs. Make sure that your VM is running one of these editions. For additional requirements on each operating system see “Dynamic Memory Configuration Guidelines” here. SQL Server Requirements All versions of SQL Server support Hyper-V Dynamic Memory. However, only certain editions of SQL Server are aware of dynamically changing system memory. To have a truly dynamic environment for your SQL Server VMs make sure that you are running one of the SQL Server editions listed below: · SQL Server 2005 Enterprise · SQL Server 2008 Enterprise / Datacenter Editions · SQL Server 2008 R2 Enterprise / Datacenter Editions Configuration guidelines for other versions of SQL Server are covered below in the FAQ section. Guidelines for configuring Dynamic Memory Parameters Here is how to configure Dynamic Memory for your SQL VMs in a nutshell: Hyper-V Dynamic Memory Parameter Recommendation Startup RAM 1 GB + SQL Min Server Memory Maximum RAM > SQL Max Server Memory Memory Buffer % 5 Memory Weight Based on performance needs Startup RAM In order to ensure that your SQL Server VMs can start correctly, ensure that Startup RAM is higher than configured SQL Min Server Memory for your VMs. Otherwise SQL Server service will need to do paging in order to start since it will not be able to see enough memory during startup. Also note that Startup Memory will always be reserved for your VMs. This will guarantee a certain level of performance for your SQL Servers, however setting this too high will limit the consolidation benefits you’ll get out of your virtualization environment. Maximum RAM This one is obvious. If you’ve configured SQL Max Server Memory for your SQL Server, make sure that Dynamic Memory Maximum RAM configuration is higher than this value. Otherwise your SQL Server will not grow to memory values higher than the value configured for Dynamic Memory. Memory Buffer % Memory buffer configuration is used to provision file cache to virtual machines in order to improve performance. Due to the fact that SQL Server is managing its own buffer pool, Memory Buffer setting should be configured to the lowest value possible, 5%. Configuring a higher memory buffer will prevent low resource notifications from Windows Memory Manager and it will prevent reclaiming memory from SQL Server VMs. Memory Weight Memory weight configuration defines the importance of memory to a VM. Configure higher values for the VMs that have higher performance requirements. VMs with higher memory weight will have more memory under high memory pressure conditions on your host. Questions and Answers Q1 – Which SQL Server memory model is best for Dynamic Memory? The best SQL Server model for Dynamic Memory is “Locked Page Memory Model”. This memory model ensures that SQL Server memory is never paged out and it’s also adaptive to dynamically changing memory in the system. This will be extremely useful when Dynamic Memory is attempting to remove memory from SQL Server VMs ensuring no SQL Server memory is paged out. You can find instructions on configuring “Locked Page Memory Model” for your SQL Servers here. Q2 – What about other SQL Server Editions, how should I configure Dynamic Memory for them? Other editions of SQL Server do not adapt to dynamically changing environments. They will determine how much memory they should allocate during startup and don’t change this value afterwards. Therefore make sure that you configure a higher startup memory for your VM because that will be all the memory that SQL Server utilize Tune Maximum Memory and Memory Buffer based on the other workloads running on the system. If there are no other workloads consider using Static Memory for these editions. Q3 – What if I have multiple SQL Server instances in a VM? Having multiple SQL Server instances in a VM is not a general recommendation for predictable performance, manageability and isolation. In order to achieve a predictable behavior make sure that you configure SQL Min Server Memory and SQL Max Server Memory for each instance in the VM. And make sure that: · Dynamic Memory Startup Memory is greater than the sum of SQL Min Server Memory values for the instances in the VM · Dynamic Memory Maximum Memory is greater than the sum of SQL Max Server Memory values for the instances in the VM Q4 – I’m using Large Page Memory Model for my SQL Server. Can I still use Dynamic Memory? The short answer is no. SQL Server does not dynamically change its memory size when configured with Large Page Memory Model. In virtualized environments Hyper-V provides large page support by default. Most of the time, Large Page Memory Model doesn’t bring any benefits to a SQL Server if it’s running in virtualized environments. Q5 – How do I monitor SQL performance when I’m trying Dynamic Memory on my VMs? Use the performance counters below to monitor memory performance for SQL Server: Process - Working Set: This counter is available in the VM via process performance counters. It represents the actual amount of physical memory being used by SQL Server process in the VM. SQL Server – Buffer Cache Hit Ratio: This counter is available in the VM via SQL Server counters. This represents the paging being done by SQL Server. A rate of 90% or higher is desirable. Conclusion These blog posts are a quick start to a story that will be developing more in the near future. We’re still continuing our testing and investigations to provide more detailed configuration guidelines with example performance numbers with a white paper in the upcoming months. Now it’s time to give SQL Server and Hyper-V Dynamic Memory a try. Use this guidelines to kick-start your environment. See what you think about it and let us know of your experiences. - Serdar Sutay Originally posted at http://blogs.msdn.com/b/sqlosteam/

Read the article

ODI 12c - Parallel Table Load

- by David Allan

In this post we will look at the ODI 12c capability of parallel table load from the aspect of the mapping developer and the knowledge module developer - two quite different viewpoints. This is about parallel table loading which isn't to be confused with loading multiple targets per se. It supports the ability for ODI mappings to be executed concurrently especially if there is an overlap of the datastores that they access, so any temporary resources created may be uniquely constructed by ODI. Temporary objects can be anything basically - common examples are staging tables, indexes, views, directories - anything in the ETL to help the data integration flow do its job. In ODI 11g users found a few workarounds (such as changing the technology prefixes - see here) to build unique temporary names but it was more of a challenge in error cases. ODI 12c mappings by default operate exactly as they did in ODI 11g with respect to these temporary names (this is also true for upgraded interfaces and scenarios) but can be configured to support the uniqueness capabilities. We will look at this feature from two aspects; that of a mapping developer and that of a developer (of procedures or KMs). 1. Firstly as a Mapping Developer..... 1.1 Control when uniqueness is enabled A new property is available to set unique name generation on/off. When unique names have been enabled for a mapping, all temporary names used by the collection and integration objects will be generated using unique names. This property is presented as a check-box in the Property Inspector for a deployment specification. 1.2 Handle cleanup after successful execution Provided that all temporary objects that are created have a corresponding drop statement then all of the temporary objects should be removed during a successful execution. This should be the case with the KMs developed by Oracle. 1.3 Handle cleanup after unsuccessful execution If an execution failed in ODI 11g then temporary tables would have been left around and cleaned up in the subsequent run. In ODI 12c, KM tasks can now have a cleanup-type task which is executed even after a failure in the main tasks. These cleanup tasks will be executed even on failure if the property 'Remove Temporary Objects on Error' is set. If the agent was to crash and not be able to execute this task, then there is an ODI tool (OdiRemoveTemporaryObjects here) you can invoke to cleanup the tables - it supports date ranges and the like. That's all there is to it from the aspect of the mapping developer it's much, much simpler and straightforward. You can now execute the same mapping concurrently or execute many mappings using the same resource concurrently without worrying about conflict. 2. Secondly as a Procedure or KM Developer..... In the ODI Operator the executed code shows the actual name that is generated - you can also see the runtime code prior to execution (introduced in 11.1.1.7), for example below in the code type I selected 'Pre-executed Code' this lets you see the code about to be processed and you can also see the executed code (which is the default view). References to the collection (C$) and integration (I$) names will be automatically made unique by using the odiRef APIs - these objects will have unique names whenever concurrency has been enabled for a particular mapping deployment specification. It's also possible to use name uniqueness functions in procedures and your own KMs. 2.1 New uniqueness tags You can also make your own temporary objects have unique names by explicitly including either %UNIQUE_STEP_TAG or %UNIQUE_SESSION_TAG in the name passed to calls to the odiRef APIs. Such names would always include the unique tag regardless of the concurrency setting. To illustrate, let's look at the getObjectName() method. At <% expansion time, this API will append %UNIQUE_STEP_TAG to the object name for collection and integration tables. The name parameter passed to this API may contain %UNIQUE_STEP_TAG or %UNIQUE_SESSION_TAG. This API always generates to the <? version of getObjectName() At execution time this API will replace the unique tag macros with a string that is unique to the current execution scope. The returned name will conform to the name-length restriction for the target technology, and its pattern for the unique tag. Any necessary truncation will be performed against the initial name for the object and any other fixed text that may have been specified. Examples are:- <?=odiRef.getObjectName("L", "%COL_PRFEMP%UNIQUE_STEP_TAG", "D")?> SCOTT.C$_EABH7QI1BR1EQI3M76PG9SIMBQQ <?=odiRef.getObjectName("L", "EMP%UNIQUE_STEP_TAG_AE", "D")?> SCOTT.EMPAO96Q2JEKO0FTHQP77TMSAIOSR_ Methods which have this kind of support include getFrom, getTableName, getTable, getObjectShortName and getTemporaryIndex. There are APIs for retrieving this tag info also, the getInfo API has been extended with the following properties (the UNIQUE* properties can also be used in ODI procedures); UNIQUE_STEP_TAG - Returns the unique value for the current step scope, e.g. 5rvmd8hOIy7OU2o1FhsF61 Note that this will be a different value for each loop-iteration when the step is in a loop. UNIQUE_SESSION_TAG - Returns the unique value for the current session scope, e.g. 6N38vXLrgjwUwT5MseHHY9 IS_CONCURRENT - Returns info about the current mapping, will return 0 or 1 (only in % phase) GUID_SRC_SET - Returns the UUID for the current source set/execution unit (only in % phase) The getPop API has been extended with the IS_CONCURRENT property which returns info about an mapping, will return 0 or 1. 2.2 Additional APIs Some new APIs are provided including getFormattedName which will allow KM developers to construct a name from fixed-text or ODI symbols that can be optionally truncate to a max length and use a specific encoding for the unique tag. It has syntax getFormattedName(String pName[, String pTechnologyCode]) This API is available at both the % and the ? phase. The format string can contain the ODI prefixes that are available for getObjectName(), e.g. %INT_PRF, %COL_PRF, %ERR_PRF, %IDX_PRF alongwith %UNIQUE_STEP_TAG or %UNIQUE_SESSION_TAG. The latter tags will be expanded into a unique string according to the specified technology. Calls to this API within the same execution context are guaranteed to return the same unique name provided that the same parameters are passed to the call. e.g. <%=odiRef.getFormattedName("%COL_PRFMY_TABLE%UNIQUE_STEP_TAG_AE", "ORACLE")%> <?=odiRef.getFormattedName("%COL_PRFMY_TABLE%UNIQUE_STEP_TAG_AE", "ORACLE")?> C$_MY_TAB7wDiBe80vBog1auacS1xB_AE <?=odiRef.getFormattedName("%COL_PRFMY_TABLE%UNIQUE_STEP_TAG.log", "FILE")?> C2_MY_TAB7wDiBe80vBog1auacS1xB.log 2.3 Name length generation As part of name generation, the length of the generated name will be compared with the maximum length for the target technology and truncation may need to be applied. When a unique tag is included in the generated string it is important that uniqueness is not compromised by truncation of the unique tag. When a unique tag is NOT part of the generated name, the name will be truncated by removing characters from the end - this is the existing 11g algorithm. When a unique tag is included, the algorithm will first truncate the <postfix> and if necessary the <prefix>. It is recommended that users will ensure there is sufficient uniqueness in the <prefix> section to ensure uniqueness of the final resultant name. SUMMARY To summarize, ODI 12c make it much simpler to utilize mappings in concurrent cases and provides APIs for helping developing any procedures or custom knowledge modules in such a way they can be used in highly concurrent, parallel scenarios.

Read the article

RSS feeds in Orchard

- by Bertrand Le Roy

When we added RSS to Orchard, we wanted to make it easy for any module to expose any contents as a feed. We also wanted the rendering of the feed to be handled by Orchard in order to minimize the amount of work from the module developer. A typical example of such feed exposition is of course blog feeds. We have an IFeedManager interface for which you can get the built-in implementation through dependency injection. Look at the BlogController constructor for an example: public BlogController( IOrchardServices services, IBlogService blogService, IBlogSlugConstraint blogSlugConstraint, IFeedManager feedManager, RouteCollection routeCollection) { If you look a little further in that same controller, in the Item action, you’ll see a call to the Register method of the feed manager: _feedManager.Register(blog); This in reality is a call into an extension method that is specialized for blogs, but we could have made the two calls to the actual generic Register directly in the action instead, that is just an implementation detail: feedManager.Register(blog.Name, "rss", new RouteValueDictionary { { "containerid", blog.Id } }); feedManager.Register(blog.Name + " - Comments", "rss", new RouteValueDictionary { { "commentedoncontainer", blog.Id } }); What those two effective calls are doing is to register two feeds: one for the blog itself and one for the comments on the blog. For each call, the name of the feed is provided, then we have the type of feed (“rss”) and some values to be injected into the generic RSS route that will be used later to route the feed to the right providers. This is all you have to do to expose a new feed. If you’re only interested in exposing feeds, you can stop right there. If on the other hand you want to know what happens after that under the hood, carry on. What happens after that is that the feedmanager will take care of formatting the link tag for the feed (see FeedManager.GetRegisteredLinks). The GetRegisteredLinks method itself will be called from a specialized filter, FeedFilter. FeedFilter is an MVC filter and the event we’re interested in hooking into is OnResultExecuting, which happens after the controller action has returned an ActionResult and just before MVC executes that action result. In other words, our feed registration has already been called but the view is not yet rendered. Here’s the code for OnResultExecuting: model.Zones.AddAction("head:after", html => html.ViewContext.Writer.Write( _feedManager.GetRegisteredLinks(html))); This is another piece of code whose execution is differed. It is saying that whenever comes time to render the “head” zone, this code should be called right after. The code itself is rendering the link tags. As a result of all that, here’s what can be found in an Orchard blog’s head section: <link rel="alternate" type="application/rss+xml" title="Tales from the Evil Empire" href="/rss?containerid=5" /> <link rel="alternate" type="application/rss+xml" title="Tales from the Evil Empire - Comments" href="/rss?commentedoncontainer=5" /> The generic action that these two feeds point to is Index on FeedController. That controller has three important dependencies: an IFeedBuilderProvider, an IFeedQueryProvider and an IFeedItemProvider. Different implementations of these interfaces can provide different formats of feeds, such as RSS and Atom. The Match method enables each of the competing providers to provide a priority for themselves based on arbitrary criteria that can be found on the FeedContext. This means that a provider can be selected based not only on the desired format, but also on the nature of the objects being exposed as a feed or on something even more arbitrary such as the destination device (you could imagine for example giving shorter text only excerpts of posts on mobile devices, and full HTML on desktop). The key here is extensibility and dynamic competition and collaboration from unknown and loosely coupled parts. You’ll find this pattern pretty much everywhere in the Orchard architecture. The RssFeedBuilder implementation of IFeedBuilderProvider is also a regular controller with a Process action that builds a RssResult, which is itself a thin ActionResult wrapper around an XDocument. Let’s get back to the FeedController’s Index action. After having called into each known feed builder to get its priority on the currently requested feed, it will select the one with the highest priority. The next thing it needs to do is to actually fetch the data for the feed. This again is a collaborative effort from a priori unknown providers, the implementations of IFeedQueryProvider. There are several implementations by default in Orchard, the choice of which is again done through a Match method. ContainerFeedQuery for example chimes in when a “containerid” parameter is found in the context (see URL in the link tag above): public FeedQueryMatch Match(FeedContext context) { var containerIdValue = context.ValueProvider.GetValue("containerid"); if (containerIdValue == null) return null; return new FeedQueryMatch { FeedQuery = this, Priority = -5 }; } The actual work is done in the Execute method, which finds the right container content item in the Orchard database and adds elements for each of them. In other words, the feed query provider knows how to retrieve the list of content items to add to the feed. The last step is to translate each of the content items into feed entries, which is done by implementations of IFeedItemBuilder. There is no Match method this time. Instead, all providers are called with the collection of items (or more accurately with the FeedContext, but this contains the list of items, which is what’s relevant in most cases). Each provider can then choose to pick those items that it knows how to treat and transform them into the format requested. This enables the construction of heterogeneous feeds that expose content items of various types into a single feed. That will be extremely important when you’ll want to expose a single feed for all your site. So here are feeds in Orchard in a nutshell. The main point here is that there is a fair number of components involved, with some complexity in implementation in order to allow for extreme flexibility, but the part that you use to expose a new feed is extremely simple and light: declare that you want your content exposed as a feed and you’re done. There are cases where you’ll have to dive in and provide new implementations for some or all of the interfaces involved, but that requirement will only arise as needed. For example, you might need to create a new feed item builder to include your custom content type but that effort will be extremely focused on the specialized task at hand. The rest of the system won’t need to change. So what do you think?

Read the article

Web Platform Installer bundles for Visual Studio 2010 SP1 - and how you can build your own WebPI bundles

- by Jon Galloway

Visual Studio SP1 is now available via the Web Platform Installer, which means you've got three options: Download the 1.5 GB ISO image Run the 750KB Web Installer (which figures out what you need to download) Install via Web PI Note: I covered some tips for installing VS2010 SP1 last week - including some that apply to all of these, such as removing options you don't use prior to installing the service pack to decrease the installation time and download size. Two Visual Studio 2010 SP1 Web PI packages There are actually two WebPI packages for VS2010 SP1. There's the standard Visual Studio 2010 SP1 package [Web PI link], which includes (quoting ScottGu's post): VS2010 2010 SP1 ASP.NET MVC 3 (runtime + tools support) IIS 7.5 Express SQL Server Compact Edition 4.0 (runtime + tools support) Web Deployment 2.0 The notes on that package sum it up pretty well: Looking for the latest everything? Look no further. This will get you Visual Studio 2010 Service Pack 1 and the RTM releases of ASP.NET MVC 3, IIS 7.5 Express, SQL Server Compact 4.0 with tooling, and Web Deploy 2.0. It's the value meal of Microsoft products. Tell your friends! Note: This bundle includes the Visual Studio 2010 SP1 web installer, which will dynamically determine the appropriate service pack components to download and install. This is typically in the range of 200-500 MB and will take 30-60 minutes to install, depending on your machine configuration. There is also a Visual Studio 2010 SP1 Core package [Web PI link], which only includes only the SP without any of the other goodies (MVC3, IIS Express, etc.). If you're doing any web development, I'd highly recommend the main pack since it the other installs are small, simple installs, but if you're working in another space, you might want the core package. Installing via the Web Platform Installer I generally like to go with the Web PI when possible since it simplifies most software installations due to things like: Smart dependency management - installing apps or tools which have software dependencies will automatically figure out which dependencies you don't have and add them to the list (which you can review before install) Simultaneous download and install - if your install includes more than one package, it will automatically pull the dependencies first and begin installing them while downloading the others Lists the latest downloads - no need to search around, as they're all listed based on a live feed Includes open source applications - a lot of popular open source applications are included as well as Microsoft software and tools No worries about reinstallation - WebPI installations detect what you've got installed, so for instance if you've got MVC 3 installed you don't need to worry about the VS2010 SP1 package install messing anything up In addition to the links I included above, you can install the WebPI from http://www.microsoft.com/web/downloads/platform.aspx, and if you have Web PI installed you can just tap the Windows key and type "Web Platform" to bring it up in the Start search list. You'll see Visual Studio SP1 listed in the spotlight list as shown below. That's the standard package, which includes MVC 3 / IIS 7.5 Express / SQL Compact / Web Deploy. If you just want the core install, you can use the search box in the upper right corner, typing in "Visual Studio SP1" as shown. Core Install: Use Web PI or the Visual Studio Web Installer? I think the big advantage of using Web PI to install VS 2010 SP1 is that it includes the other new bits. If you're going to install the SP1 core, I don't think there's as much advantage to using Web PI, as the Web PI Core install just downloads the Visual Studio Web Installer anyways. I think Web PI makes it a little easier to find the download, but not a lot. The Visual Studio Web Installer checks dependencies, so there's no big advantage there. If you do happen to hit any problems installing Visual Studio SP1 via Web PI, I'd recommend running the Visual Studio Web Installer, then running the Web PI VS 2010 SP1 package to get all the other goodies. I talked to one person who hit some random snag, recommended that, and it worked out. Custom Web Platform Installer bundles You can create links that will launch the Web Platform Installer with a custom list of tools. You can see an example of this by clicking through on the install button at http://asp.net/downloads (cancelling the installation dialog). You'll see this in the address bar: http://www.microsoft.com/web/gallery/install.aspx?appsxml=&appid=MVC3;ASPNET;NETFramework4;SQLExpress;VWD Notice that the appid querystring parameter includes a semicolon delimited list, and you can make your own custom Web PI links with your own desired app list. I can think of a lot of cases where that would be handy: linking to a recommended software configuration from a software project or product, setting up a recommended / documented / supported install list for a software development team or IT shop, etc. For instance, here's a link that installs just VS2010 SP1 Core and the SQL CE tools: http://www.microsoft.com/web/gallery/install.aspx?appsxml=&appid=VS2010SP1Core;SQLCETools Note: If you've already got all or some of the products installed, the display will reflect that. On my dev box which has the full SP1 package, here's what the above link gives me: Here's another example - on a fresh box I created a link to install MVC 3 and the Web Farm Framework (http://www.microsoft.com/web/gallery/install.aspx?appsxml=&appid=MVC3;WebFarmFramework) and got the following items added to the cart: But where do I get the App ID's? Aha, that's the trick. You can link to a list of cool packages, but you need to know the App ID's to link to them. To figure that out, I turned on tracing in Web Platform Installer (also handy if you're ever having trouble with a WebPI install) and from the trace logs saw that the list of packages is pulled from an XML file: DownloadManager Information: 0 : Loading product xml from: https://go.microsoft.com/?linkid=9763242 DownloadManager Verbose: 0 : Connecting to https://go.microsoft.com/?linkid=9763242 with (partial) headers: Referer: wpi://2.1.0.0/Microsoft Windows NT 6.1.7601 Service Pack 1 If-Modified-Since: Wed, 09 Mar 2011 14:15:27 GMT User-Agent:Platform-Installer/3.0.3.0(Microsoft Windows NT 6.1.7601 Service Pack 1) DownloadManager Information: 0 : https://go.microsoft.com/?linkid=9763242 responded with 302 DownloadManager Information: 0 : Response headers: HTTP/1.1 302 Found Cache-Control: private Content-Length: 175 Content-Type: text/html; charset=utf-8 Expires: Wed, 09 Mar 2011 22:52:28 GMT Location: https://www.microsoft.com/web/webpi/3.0/webproductlist.xml Server: Microsoft-IIS/7.5 X-AspNet-Version: 2.0.50727 X-Powered-By: ASP.NET Date: Wed, 09 Mar 2011 22:53:27 GMT Browsing to https://www.microsoft.com/web/webpi/3.0/webproductlist.xml shows the full list. You can search through that in your browser / text editor if you'd like, open it in Excel as an XML table, etc. Here's a list of the App ID's as of today: SMO SMO32 PHP52ForIISExpress PHP53ForIISExpress StaticContent DefaultDocument DirectoryBrowse HTTPErrors HTTPRedirection ASPNET NETExtensibility ASP CGI ISAPIExtensions ISAPIFilters ServerSideIncludes HTTPLogging LoggingTools RequestMonitor Tracing CustomLogging ODBCLogging BasicAuthentication WindowsAuthentication DigestAuthentication ClientCertificateMappingAuthentication IISClientCertificateMappingAuthentication URLAuthorization RequestFiltering IPSecurity StaticContentCompression DynamicContentCompression IISManagementConsole IISManagementScriptsAndTools ManagementService MetabaseAndIIS6Compatibility WASProcessModel WASNetFxEnvironment WASConfigurationAPI IIS6WPICompatibility IIS6ScriptingTools IIS6ManagementConsole LegacyFTPServer FTPServer WebDAV LegacyFTPManagementConsole FTPExtensibility AdminPack AdvancedLogging WebFarmFrameworkNonLoc ExternalCacheNonLoc WebFarmFramework WebFarmFrameworkv2 WebFarmFrameworkv2_beta ExternalCache ECacheUpdate ARRv1 ARRv2Beta1 ARRv2Beta2 ARRv2RC ARRv2NonLoc ARRv2 ARRv2Update MVC MVCBeta MVCRC1 MVCRC2 DBManager DbManagerUpdate DynamicIPRestrictions DynamicIPRestrictionsUpdate DynamicIPRestrictionsLegacy DynamicIPRestrictionsBeta2 FTPOOB IISPowershellSnapin RemoteManager SEOToolkit VS2008RTM MySQL SQLDriverPHP52IIS SQLDriverPHP53IIS SQLDriverPHP52IISExpress SQLDriverPHP53IISExpress SQLExpress SQLManagementStudio SQLExpressAdv SQLExpressTools UrlRewrite UrlRewrite2 UrlRewrite2NonLoc UrlRewrite2RC UrlRewrite2Beta UrlRewrite10 UrlScan MVC3Installer MVC3 MVC3LocInstaller MVC3Loc MVC2 VWD VWD2010SP1Pack NETFramework4 WebMatrix WebMatrix_v1Refresh IISExpress IISExpress_v1 IIS7 AspWebPagesVS AspWebPagesVS_1_0 Plan9 Plan9Loc WebMatrix_WHP SQLCE SQLCETools SQLCEVSTools SQLCEVSTools_4_0 SQLCEVSToolsInstaller_4_0 SQLCEVSToolsInstallerNew_4_0 SQLCEVSToolsInstallerRepair_EN_4_0 SQLCEVSToolsInstallerRepair_JA_4_0 SQLCEVSToolsInstallerRepair_FR_4_0 SQLCEVSToolsInstallerRepair_DE_4_0 SQLCEVSToolsInstallerRepair_ES_4_0 SQLCEVSToolsInstallerRepair_IT_4_0 SQLCEVSToolsInstallerRepair_RU_4_0 SQLCEVSToolsInstallerRepair_KO_4_0 SQLCEVSToolsInstallerRepair_ZH_CN_4_0 SQLCEVSToolsInstallerRepair_ZH_TW_4_0 VWD2008 WebDAVOOB WDeploy WDeploy_v2 WDeployNoSMO WDeploy11 WinCache52 WinCache53 NETFramework35 WindowsImagingComponent VC9Redist NETFramework20SP2 WindowsInstaller31 PowerShell PowerShellMsu PowerShell2 WindowsInstaller45 FastCGIUpdate FastCGIBackport FastCGIIIS6 IIS51 IIS60 SQLNativeClient SQLNativeClient2008 SQLNativeClient2005 SQLCLRTypes SQLCLRTypes32 SMO_10_1 MySQLConnector PHP52 PHP53 PHPManager VSVWD2010Feature VWD2010WebFeature_0 VWD2010WebFeature_1 VWD2010WebFeature_2 VS2010SP1Prerequisite RIAServicesToolkitMay2010 Silverlight4Toolkit Silverlight4Tools VSLS SSMAMySQL WebsitePanel VS2010SP1Core VS2010SP1Installer VS2010SP1Pack MissingVWDOrVSVWD2010Feature VB2010Beta2Express VCS2010Beta2Express VC2010Beta2Express RIAServicesToolkitApr2010 VS2010Beta1 VS2010RC VS2010Beta2 VS2010Beta2Express VS2k8RTM VSCPP2k8RTM VSVB2k8RTM VSCS2k8RTM VSVWDFeature LegacyWinCache SQLExpress2005 SSMS2005

Read the article

Using Unity – Part 6

- by nmarun

This is the last of the ‘Unity’ series and I’ll be talking about generics here. If you’ve been following the previous articles, you must have noticed that I’m just adding more and more ‘Product’ classes to the project. I’ll change that trend in this blog where I’ll be adding an ICaller interface and a Caller class. 1: public interface ICaller<T> where T : IProduct 2: { 3: string CallMethod<T>(string typeName); 4: } 5: 6: public class Caller<T> : ICaller<T> where T:IProduct 7: { 8: public string CallMethod<T>(string typeName) 9: { 10: //... 11: } 12: } We’ll fill-in the implementation of the CallMethod in a few, but first, here’s what we’re going to do: create an instance of the Caller class pass it the IProduct as a generic parameter in the CallMethod method, we’ll use Unity to dynamically create an instance of IProduct implemented object I need to add the config information for ICaller and Caller types. 1: <typeAlias alias="ICaller`1" type="ProductModel.ICaller`1, ProductModel" /> 2: <typeAlias alias="Caller`1" type="ProductModel.Caller`1, ProductModel" /> The .NET Framework’s convention to express generic types is ICaller`1, where the digit following the "`" matches the number of types contained in the generic type. So a generic type that contains 4 types contained in the generic type would be declared as: 1: <typeAlias alias="Caller`4" type="ProductModel.Caller`4, ProductModel" /> On my .aspx page, I have the following UI design: 1: <asp:RadioButton ID="LegacyProduct" Text="Product" runat="server" GroupName="ProductWeb" 2: AutoPostBack="true" OnCheckedChanged="RadioButton_CheckedChanged" /> 3: <br /> 4: <asp:RadioButton ID="NewProduct" Text="Product 2" runat="server" GroupName="ProductWeb" 5: AutoPostBack="true" OnCheckedChanged="RadioButton_CheckedChanged" /> 6: <br /> 7: <asp:RadioButton ID="ComplexProduct" Text="Product 3" runat="server" GroupName="ProductWeb" 8: AutoPostBack="true" OnCheckedChanged="RadioButton_CheckedChanged" /> 9: <br /> 10: <asp:RadioButton ID="ArrayConstructor" Text="Product 4" runat="server" GroupName="ProductWeb" 11: AutoPostBack="true" OnCheckedChanged="RadioButton_CheckedChanged" /> Things to note here are that all these radio buttons belong to the same GroupName => only one of these four can be clicked. Next, all four controls postback to the same ‘OnCheckedChanged’ event and lastly the ID’s point to named types of IProduct (already added to the web.config file). 1: <type type="IProduct" mapTo="Product" name="LegacyProduct" /> 2: 3: <type type="IProduct" mapTo="Product2" name="NewProduct" /> 4: 5: <type type="IProduct" mapTo="Product3" name="ComplexProduct"> 6: ... 7: </type> 8: 9: <type type="IProduct" mapTo="Product4" name="ArrayConstructor"> 10: ... 11: </type> In my calling code, I see which radio button was clicked, pass that as an argument to the CallMethod method. 1: protected void RadioButton_CheckedChanged(object sender, EventArgs e) 2: { 3: string typeName = ((RadioButton)sender).ID; 4: ICaller<IProduct> caller = unityContainer.Resolve<ICaller<IProduct>>(); 5: productDetailsLabel.Text = caller.CallMethod<IProduct>(typeName); 6: } What’s basically happening here is that the ID of the control gets passed on to the typeName which will be one of “LegacyProduct”, “NewProduct”, “ComplexProduct” or “ArrayConstructor”. I then create an instance of an ICaller and pass the typeName to it. Now, we’ll fill in the blank for the CallMethod method (sorry for the naming guys). 1: public string CallMethod<T>(string typeName) 2: { 3: IUnityContainer unityContainer = HttpContext.Current.Application["UnityContainer"] as IUnityContainer; 4: T productInstance = unityContainer.Resolve<T>(typeName); 5: return ((IProduct)productInstance).WriteProductDetails(); 6: } This is where I’ll resolve the IProduct by passing the type name and calling the WriteProductDetails() method. With all things in place, when I run the application and choose different radio buttons, the output should look something like below: Basically this is how generics come to play in Unity. Please see the code I’ve used for this here. This marks the end of the ‘Unity’ series. I’ll definitely post any updates that I find, but for now I don’t have anything planned.

Read the article

Building extensions for Expression Blend 4 using MEF

- by Timmy Kokke

Introduction Although it was possible to write extensions for Expression Blend and Expression Design, it wasn’t very easy and out of the box only one addin could be used. With Expression Blend 4 it is possible to write extensions using MEF, the Managed Extensibility Framework. Until today there’s no documentation on how to build these extensions, so look thru the code with Reflector is something you’ll have to do very often. Because Blend and Design are build using WPF searching the visual tree with Snoop and Mole belong to the tools you’ll be using a lot exploring the possibilities. Configuring the extension project Extensions are regular .NET class libraries. To create one, load up Visual Studio 2010 and start a new project. Because Blend is build using WPF, choose a WPF User Control Library from the Windows section and give it a name and location. I named mine DemoExtension1. Because Blend looks for addins named *.extension.dll you’ll have to tell Visual Studio to use that in the Assembly Name. To change the Assembly Name right click your project and go to Properties. On the Application tab, add .Extension to name already in the Assembly name text field. To be able to debug this extension, I prefer to set the output path on the Build tab to the extensions folder of Expression Blend. This means that everything that used to go into the Debug folder is placed in the extensions folder. Including all referenced assemblies that have the copy local property set to false. One last setting. To be able to debug your extension you could start Blend and attach the debugger by hand. I like it to be able to just hit F5. Go to the Debug tab and add the the full path to Blend.exe in the Start external program text field. Extension Class Add a new class to the project. This class needs to be inherited from the IPackage interface. The IPackage interface can be found in the Microsoft.Expression.Extensibility namespace. To get access to this namespace add Microsoft.Expression.Extensibility.dll to your references. This file can be found in the same folder as the (Expression Blend 4 Beta) Blend.exe file. Make sure the Copy Local property is set to false in this reference. After implementing the interface the class would look something like: using Microsoft.Expression.Extensibility; namespace DemoExtension1 { public class DemoExtension1:IPackage { public void Load(IServices services) { } public void Unload() { } } } These two methods are called when your addin is loaded and unloaded. The parameter passed to the Load method, IServices services, is your main entry point into Blend. The IServices interface exposes the GetService<T> method. You will be using this method a lot. Almost every part of Blend can be accessed thru a service. For example, you can use to get to the commanding services of Blend by calling GetService<ICommandService>() or to get to the Windowing services by calling GetService<IWindowService>(). To get Blend to load the extension we have to implement MEF. (You can get up to speed on MEF on the community site or read the blog of Mr. MEF, Glenn Block.) In the case of Blend extensions, all that needs to be done is mark the class with an Export attribute and pass it the type of IPackage. The Export attribute can be found in the System.ComponentModel.Composition namespace which is part of the .NET 4 framework. You need to add this to your references. using System.ComponentModel.Composition; using Microsoft.Expression.Extensibility; namespace DemoExtension1 { [Export(typeof(IPackage))] public class DemoExtension1:IPackage { Blend is able to find your addin now. Adding UI The addin doesn’t do very much at this point. The WPF User Control Library came with a UserControl so lets use that in this example. I just drop a Button and a TextBlock onto the surface of the control to have something to show in the demo. To get the UserControl to work in Blend it has to be registered with the WindowService. Call GetService<IWindowService>() on the IServices interface to get access to the windowing services. The UserControl will be used in Blend on a Palette and has to be registered to enable it. This is done by calling the RegisterPalette on the IWindowService interface and passing it an identifier, an instance of the UserControl and a caption for the palette. public void Load(IServices services) { IWindowService windowService = services.GetService<IWindowService>(); UserControl1 uc = new UserControl1(); windowService.RegisterPalette("DemoExtension", uc, "Demo Extension"); } After hitting F5 to start debugging Expression Blend will start. You should be able to find the addin in the Window menu now. Activating this window will show the “Demo Extension” palette with the UserControl, style according to the settings of Blend. Now what? Because little is publicly known about how to access different parts of Blend adding breakpoints in Debug mode and browsing thru objects using the Quick Watch feature of Visual Studio is something you have to do very often. This demo extension can be used for that purpose very easily. Add the click event handler to the button on the UserControl. Change the contructor to take the IServices interface and store this in a field. Set a breakpoint in the Button_Click method. public partial class UserControl1 : UserControl { private readonly IServices _services; public UserControl1(IServices services) { _services = services; InitializeComponent(); } private void button1_Click(object sender, RoutedEventArgs e) { } } Change the call to the constructor in the load method and pass it the services property. public void Load(IServices services) { IWindowService service = services.GetService<IWindowService>(); UserControl1 uc = new UserControl1(services); service.RegisterPalette("DemoExtension", uc, "Demo Extension"); } Hit F5 to compile and start Blend. Got to the window menu and start show the addin. Click on the button to hit the breakpoint. Now place the carrot text _services text in the code window and hit Shift+F9 to show the Quick Watch window. Now start exploring and discovering where to find everything you need. More Information The are no official resources available yet. Microsoft has released one extension for expression Blend that is very useful as a reference, the Microsoft Expression Blend® Add-in Preview for Windows® Phone. This will install a .extension.dll file in the extension folder of Blend. You can load this file with Reflector and have a peek at how Microsoft is building his addins. Conclusion I hope this gives you something to get started building extensions for Expression Blend. Until Microsoft releases the final version, which hopefully includes more information about building extensions, we’ll have to work on documenting it in the community.

Search Results

Search found 7375 results on 295 pages for 'out parameter'.

Page 277/295 | < Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284 | Next Page >

- by Grzenio

- by Charlie Somerville

- by Olaf Erlandsen

- by Stefan Lasiewski

- by John Gallagher

- by arheops

- by Joy

- by Bil Simser

- by mbridge

- by SeanMcAlinden

- by Rantanplan

- by Jakob Ehn

- by shiju

- by Piet

- by cj

- by kazimanzurrashid

- by jsavit

- by Sky Sanders

- by kazimanzurrashid

- by SQLOS Team

- by David Allan

- by Bertrand Le Roy

- by Jon Galloway

- by nmarun

- by Timmy Kokke

< Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284 | Next Page >