Search Results

Search found 1370 results on 55 pages for 'nat gr'.

Page 28/55 | < Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >

  • Cisco BVI: Claiming IP addresses

    - by cjavapro
    I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

    Read the article

  • openvpn problem

    - by Jared Voronik
    I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

    Read the article

  • Slackware - Assigning routes (IP address ranges) to one of many network adapters

    - by Dogbert
    I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

    Read the article

  • dhcp3-server (dhcpd) is tampering with host NIC

    - by user61000
    Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

    Read the article

  • Can I use iptables on my Varnish server to forward HTTPS traffic to a specific server?

    - by Dylan Beattie
    We use Varnish as our front-end web cache and load balancer, so we have a Linux server in our development environment, running Varnish with some basic caching and load-balancing rules across a pair of Windows 2008 IIS web servers. We have a wildcard DNS rule that points *.development at this Varnish box, so we can browse http://www.mysite.com.development, http://www.othersite.com.development, etc. The problem is that since Varnish can't handle HTTPS traffic, we can't access https://www.mysite.com.development/ For dev/testing, we don't need any acceleration or load-balancing - all I need is to tell this box to act as a dumb proxy and forward any incoming requests on port 443 to a specific IIS server. I suspect iptables may offer a solution but it's been a long while since I wrote an iptables rule. Some initial hacking has got me as far as iptables -F iptables -A INPUT -p tcp -m tcp --sport 443 -j ACCEPT iptables -A OUTPUT -p tcp -m tcp --dport 443 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 443 -j DNAT --to 10.0.0.241:443 iptables -t nat -A POSTROUTING -p tcp -d 10.0.0.241 --dport 443 -j MASQUERADE iptables -A INPUT -j LOG --log-level 4 --log-prefix 'PreRouting ' iptables -A OUTPUT -j LOG --log-level 4 --log-prefix 'PostRouting ' iptables-save > /etc/iptables.rules (where 10.0.0.241 is the IIS box hosting the HTTPS website), but this doesn't appear to be working. To clarify - I realize there's security implications about HTTPS proxying/caching - all I'm looking for is completely transparent IP traffic forwarding. I don't need to decrypt, cache or inspect any of the packets; I just want anything on port 443 to flow through the Linux box to the IIS box behind it as though the Linux box wasn't even there. Any help gratefully received... EDIT: Included full iptables config script.

    Read the article

  • IP to IP forwarding with iptables [centos]

    - by FunkyChicken
    I have 2 servers. Server 1 with ip 1.1.1.1 and server 2 with ip 2.2.2.2 My domain example.com points to 1.1.1.1 at the moment, but very soon I'm going to switch to ip 2.2.2.2. I have already setup a low TTL for domain example.com, but some people will still hit the old ip a after I change the ip address of the domain. Now both machines run centos 5.8 with iptables and nginx as a webserver. I want to forward all traffic that still hits server 1.1.1.1 to 2.2.2.2 so there won't be any downtime. Now I found this tutorial: http://www.debuntu.org/how-to-redirecting-network-traffic-a-new-ip-using-iptables but I cannot seem to get it working. I have enabled ip forwarding: echo "1" > /proc/sys/net/ipv4/ip_forward After that I ran these 2 commands: /sbin/iptables -t nat -A PREROUTING -s 1.1.1.1 -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2:80 /sbin/iptables -t nat -A POSTROUTING -j MASQUERADE But when I load http://1.1.1.1 in my browser, I still get the pages hosted on 1.1.1.1 and not the content from 2.2.2.2. What am I doing wrong?

    Read the article

  • How to set a static route for an external IP address

    - by HorusKol
    Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

    Read the article

  • Fortigate restrict traffic through one external IP

    - by Tom O'Connor
    I've got a fortigate 400A at a client's site. They've got a /26 from British Telecom, and we're using 4 of those IPs as a NAT Pool. Is there a way to say that traffic from 172.18.4.40-45 can only ever come out of (and hence go back into) x.x.x.140 as the external IP? We're having some problems with SIP which looks like it's coming out of one, and trying to go back into another. I tried enabling asymmetric routing, didn't work. I tried setting a VIP, but even when I did that, it didn't appear to do anything. Any ideas? I can probably post some firewall snippets if need be.. Tell me what you want to see. SIP ALG config system settings set sip-helper disable set sip-nat-trace disable set sip-tcp-port 5061 set sip-udp-port 5061 set multicast-forward enable end Interesting Sidenote VoIP phones, with no special configuration can register fine to proxy.sipgate.co.uk, which has an IP address of 217.10.79.16. Which is cool. Two phones are using a different provider, whose proxy IP address is 178.255.x.x. These phones can register for outbound, but inbound INVITEs never make it to the phone. Is it possible that the Fortigate is having trouble with 178.255.x.x as it's got a 255 in it? Or am I just imagining things?

    Read the article

  • IPTables forward from only one ip on my server

    - by user1307079
    I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    Read the article

  • How do I enable Ubuntu Gnome system tools

    - by RussellW
    I am running Ubuntu 10 with Gnome 2.30.2. This is a VMWare workstation image provided by another company that I do not have support in this regard. I am trying to access the graphical tools for configuring the network, users, and services but the System-Administration menu does not have these options listed. The main issue I am trying to solve is to correct the problems with the gnome menu options and network settings I have the gnome-system-tools package installed, and I am unable to run command-line versions of the tools, such as nm-applet (I get no GUI if I run that command, the process is running in the background). I realize that I can perform many tasks command-line, but I would like to use the GUI for administrative functions as I am not overly proficient for all command for restarting services and setting a static IP with a specific gateway. Further, I can run gnome-nettool, but I cannot change the IP, I can only see my network card. nm-connection-editor does not show any network cards that I can configure to change the IP. Currently, I am getting a DHCP through my NAT in VMWare, I want to set it to a specific IP address though. Preferences Menu (note some missing options) ![Preferences Menu][1] Admin Menu (note some missing options) ![Admin Menu][2] Network Tools (I can view but not change IP address) ![Network Tools][3] Network Settings (Unable to change IP address) ![Network Settings][4] Network Connections (no connections listed, not even my existing ethernet NAT connection through VMWare) ![Network Connections][5] See images here that I have referenced: 1- http://i.imgur.com/kl8pP.png 2- http://i.imgur.com/K3Cjz.png 3- Iq7Xb.png 4- 7wheV.png 5- J2ad8.png

    Read the article

  • OpenVPN - Cannot browse ipv4 websites

    - by user1494428
    I have set up an openVPN tunnel on my VPS (OpenVZ - Ubuntu 12.04). The problem is I can only browse websites which support ipv6 like google. http://whatismyv6.com/ reports me that I've an ipv6 adress, so I guess this is the problem. Server configuration: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key dh /etc/openvpn/easy-rsa/keys/dh1024.pem push "route 10.8.0.0 255.255.255.0" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" push "redirect-gateway def1" comp-lzo persist-tun persist-key status openvpn-status.log log /var/log/openvpn.log verb 3 Client configuration: client remote xx.xx.xx.xx 1194 dev tun comp-lzo ca ca.crt cert client1.crt key client1.key redirect-gateway def1 verb 3 I have configured NAT with this command: iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -j SNAT --to xx.xx.xx.xx Can someone explain me how I can make it works (forcing ipv4?) I had the same problem with another vps and I also tried on another client (All Windows 7).

    Read the article

  • How to configure iptables to use apt-get in a server?

    - by segaco
    I'm starting using iptables (newbie) to protect a linux server (specifically Debian 5.0). Before I configure the iptables settings, I can use apt-get without a problem. But after I configure the iptables, the apt-get stop working. For example I use this script in iptables: #!/bin/sh IPT=/sbin/iptables ## FLUSH $IPT -F $IPT -X $IPT -t nat -F $IPT -t nat -X $IPT -t mangle -F $IPT -t mangle -X $IPT -P INPUT DROP $IPT -P OUTPUT DROP $IPT -P FORWARD DROP $IPT -A INPUT -i lo -j ACCEPT $IPT -A OUTPUT -o lo -j ACCEPT $IPT -A INPUT -p tcp --dport 22 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 22 -j ACCEPT $IPT -A INPUT -p tcp --dport 80 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 80 -j ACCEPT $IPT -A INPUT -p tcp --dport 443 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 443 -j ACCEPT # Allow FTP connections @ port 21 $IPT -A INPUT -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT $IPT -A OUTPUT -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT # Allow Active FTP Connections $IPT -A INPUT -p tcp --sport 20 -m state --state ESTABLISHED,RELATED -j ACCEPT $IPT -A OUTPUT -p tcp --dport 20 -m state --state ESTABLISHED -j ACCEPT # Allow Passive FTP Connections $IPT -A INPUT -p tcp --sport 1024: --dport 1024: -m state --state ESTABLISHED -j ACCEPT $IPT -A OUTPUT -p tcp --sport 1024: --dport 1024: -m state --state ESTABLISHED,RELATED -j ACCEPT #DNS $IPT -A OUTPUT -p udp --dport 53 --sport 1024:65535 -j ACCEPT $IPT -A INPUT -p tcp --dport 1:1024 $IPT -A INPUT -p udp --dport 1:1024 $IPT -A INPUT -p tcp --dport 3306 -j DROP $IPT -A INPUT -p tcp --dport 10000 -j DROP $IPT -A INPUT -p udp --dport 10000 -j DROP then when I run apt-get I obtain: core:~# apt-get update 0% [Connecting to ftp.us.debian.org] [Connecting to security.debian.org] [Conne and it stalls. What rules I need to configure to make it works. Thanks

    Read the article

  • Cannot browse ipv4 websites (OpenVPN )

    - by user1494428
    I have set up an openVPN tunnel on my VPS (OpenVZ - Ubuntu 12.04). The problem is when I'm connected to the vpn, I can only browse websites which support ipv6 like google. Ipv4 sites aren't loading (no error, just waiting indefinitely). http://whatismyv6.com/ reports me that I've an ipv6 address, so I guess this is the problem. Server configuration: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key dh /etc/openvpn/easy-rsa/keys/dh1024.pem push "route 10.8.0.0 255.255.255.0" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" push "redirect-gateway def1" comp-lzo persist-tun persist-key status openvpn-status.log log /var/log/openvpn.log verb 3 Client configuration: client remote xx.xx.xx.xx 1194 dev tun comp-lzo ca ca.crt cert client1.crt key client1.key redirect-gateway def1 verb 3 I have configured NAT with this command: iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -j SNAT --to xx.xx.xx.xx Can someone explain me how I can make it works (forcing ipv4?) I had the same problem with another vps and I also tried on another client (All Windows 7).

    Read the article

  • ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

    - by chickenloop
    I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

    Read the article

  • iptables, forward traffic for ip not active on the host itself

    - by gucki
    I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

    Read the article

  • VirtualBox bridged network not working as expected

    - by iby chenko
    I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

    Read the article

  • How to make my Ubuntu an internet gateway for my Android phone

    - by yacine
    I want to use the internet of my school on my Android, the problem is they have a Squid proxy, and many applications on my phone don't use the proxy at all. The obvious solution is to install a transparent proxy on my Android to force all applications to connect through it. The problem is that I need to root the phone to make it work, and I don't want to do it because it's not really my phone and rooting is a little risky- Another solution, which is safer, is to make my computer run as a gateway, so I put my Ubuntu IP in the gateway parameter of the phone. I'm running a small proxy on my ubuntu (cntlm), so I redirect the Android traffic to it. I did it with "iptables" as follows: iptables -t nat -A PREROUTING -s 10.0.1.118 -p tcp -j REDIRECT --to-ports 8888 iptables -t nat -A PREROUTING -s 10.0.1.118 -p udp -j REDIRECT --to-ports 8888 10.0.1.118 is the IP of the phone, 8888 is the port of cntlm (proxy on my PC). Now, on the phone: When I enter www.google.com on the navigator I get nothing (web site not found, error message of Firefox). But, when I enter http://74.125.143.101 (IP of Google) I get an error message from the school proxy (so it worked in some way – my PC redirected the traffic of the phone to the Squid proxy). The error message is : The requested URL could not be retrieved while trying to process the request get / http/1.1 host 74.125.143.101 user-Agent ... ... I think the problem is in the "GET" header,it should be GET 74.125.143.101 HTTP/1.1. But I don't understand what's happening, and I'm a certified CCNA.

    Read the article

  • [openVPN] server & client on same machine . And multiple VPN servers

    - by HiWorld
    Hello everyone, im stucked configuring openvpn to build a multi vpn connection. like this: CLIENT - VPN1 - VPN2 - INTERNET Well, i already have and know how to done a normal sigle vpn but want to use a chain of vpns, so i explain what i have done and how i did it. ON VPN1. i have 1 openvpn instance running as server( where client connect to) and another as client connecting to VPN2 running as server. { Here comes the problem } when i connect VPN1 as client of VPN2 i cant connect to VPN1 from CLIENT, my question is HOW TO procced with this... Also have another third instance working as server to use VPN1 without chains. ON VPN2. 1 openvpn instance as server where VPN1 will connect and then forward to the NET. Im using TUN interface on configs. And iptables are on this way: VPN1 - openvpn ip server1 : 192.168.6.0 / ip as client of VPN2: 192.168.5.70 iptables -t nat -A POSTROUTING -s 192.168.6.0 -j SNAT --to-source 192.168.5.70 VPN2 - openvpn ip server2 : 192.168.5.0 iptables -t nat -A POSTROUTING -s 192.168.5.0/24 -j SNAT --to-source EXTERNAL_IP_TO_INTERNET Hope someone help me with this. thanks in advance

    Read the article

  • C# Instantiate class which implements generic interface

    - by Martijn B
    Hi there, I have some business classes which implements IBusinessRequest for example: public class PersonBusiness : IBusinessRequest<Person> { } Besides this I have a function: TypeHelper.CreateBusinessInstance(Type businessType, Type businessRequestType) A requirement of a business class is that they must have a parameterless constructor, which I check in the TypeHelper.CreateBusinessInstance function. I want to create a instance of type businessType (which is i.e PersonBusiness) with the generic value businessRequestType for IBusinessRequest<. How can I get this done? Thanks in Advance. Gr Martijn

    Read the article

  • StackOverflow Code Sample vs }

    - by 0plus1
    I want to ask you a question about the stackoverflow's editor. Whenever I need to write code and close a } I get the Code Sample indentation if using: Alt gr + Shift + (+*]) It's pretty annoying, is there any way to avoid this other than: Ctrl+v ? Thank you and sorry if this has been asked before.

    Read the article

  • RMI-applets - Cannot understand error message

    - by aeter
    In a simple RMI game I'm writing (an assignment in uni), I reveice: java.rmi.MarshalException: error marshalling arguments; nested exception is: java.net.SocketException: Broken pipe at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:138) at java.rmi.server.RemoteObjectInvocationHandler.invokeRemoteMethod(RemoteObjectInvocationHandler.java:178) at java.rmi.server.RemoteObjectInvocationHandler.invoke(RemoteObjectInvocationHandler.java:132) at $Proxy2.drawWorld(Unknown Source) at PlayerServerImpl$1.actionPerformed(PlayerServerImpl.java:180) at javax.swing.Timer.fireActionPerformed(Timer.java:271) at javax.swing.Timer$DoPostEvent.run(Timer.java:201) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) The error message appears after the second Player is registered with the RMI Server and the server starts to send the image (the array of pixels) to the 2 applets. The PlayerImpl and the PlayerServerImpl both extend UnicastRemoteObject. I have been struggling with other error messages for some time now, but I cannot understand how to troubleshoot this one. Please help. The relevant parts of the code are: PlayerServerImpl.java: ... timer = new Timer(10, new ActionListener() { // every 10 milliseconds do: @Override public void actionPerformed(ActionEvent e) { ... BufferedImage buff_image = new BufferedImage(GAME_APPLET_WIDTH, GAME_APPLET_HEIGHT, BufferedImage.TYPE_INT_RGB); // create a graphics context on the buffered image Graphics buff_g = buff_image.createGraphics(); ... // draw the score somewhere on the screen buff_g.drawString(score, GAME_APPLET_WIDTH - 20, 10); ... int[] rgbs = new int[GAME_APPLET_WIDTH * GAME_APPLET_HEIGHT]; int imgPixelsGrabbed[] = buff_image.getRGB(0,0,GAME_APPLET_WIDTH,GAME_APPLET_HEIGHT,rgbs,0,GAME_APPLET_WIDTH); // send the new state to the applets for (Player player : players) { player.drawWorld(imgPixelsGrabbed); System.out.println("Sent image to player"); } PlayerImpl.java: private PlayerApplet applet; public PlayerImpl(PlayerApplet applet) throws RemoteException { super(); this.applet = applet; } ... @Override public void drawWorld(int[] imgPixelsGrabbed) throws RemoteException { applet.setWorld(imgPixelsGrabbed); applet.repaint(); } ... PlayerApplet.java: ... private int[] world; // an array of pixels for the new image to be drawn ... // register players player = new PlayerImpl(applet); String serverIPAddressPort = ipAddressField.getText(); if (validateIPAddressPort(serverIPAddressPort)) { server = (PlayerServer) Naming.lookup("rmi://" + serverIPAddressPort + "/PlayerServer"); server.register(player); idPlayer = server.sendPlayerID(); ... @Override public void update(Graphics g) { buff_img = createImage((ImageProducer) new MemoryImageSource(getWidth(), getHeight(), world, 0, getWidth())); Graphics gr = buff_img.getGraphics(); paint(gr); g.drawImage(buff_img, 0, 0, this); } public void setWorld(int[] world) { this.world = world; }

    Read the article

  • display wait gif until image is fully loaded

    - by Dimitris Baltas
    Most popular browsers, while rendering an image, they display it line-by-line top-to-bottom as it loads. I have a requirement that a wait gif should be displayed while the image is loading. When the image is fully loaded then it should be displayed instead of the wait gif. If it helps, the site is http://farros.gr, main image: /images/bg.jpg and the div containing the image is named #main-content-image.

    Read the article

  • jQuery slider not visible after container div is toggled

    - by Shahar Evron
    I have a page which contains a jQuery-UI horizontal slider, created using a little function, inside a div which can be displayed / hidden by clicking on it's title, using $.toggle(). Problem is, once the div is hidden, when it is expanded the slider is gone. A simplified demo of the problem can be seen here: http://arr.gr/jquery-issue.html (file contains all relevant source code) - when clicking the "Advanced Options" title to hide and then show the div, the slider is no longer there. Any suggestions on how to work around this?

    Read the article

  • jQuery slider vanishes after container div is toggled

    - by Shahar Evron
    I have a page which contains a jQuery-UI horizontal slider, created using a little function, inside a DIV which can be displayed / hidden by clicking on it's title, using $.toggle(). Problem is, once the div is hidden, when it is expanded the slider is gone. A simplified demo of the problem can be seen here: http://arr.gr/jquery-issue.html (file contains all relevant source code) - when clicking the "Advanced Options" title to hide and then show the div, the slider is no longer there. Any suggestions on how to work around this?

    Read the article

< Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >