Search Results

Search found 10306 results on 413 pages for 'opensuse 11 3'.

Page 283/413 | < Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >

  • bonding module parameters are not shown in /sys/module/bonding/parameters/

    - by c4f4t0r
    I have a server with Suse 11 sp1 kernel 2.6.32.54-0.3-default, with modinfo bonding i see all parameters, but under /sys/module/bonding/parameters/ not modinfo bonding | grep ^parm parm: max_bonds:Max number of bonded devices (int) parm: num_grat_arp:Number of gratuitous ARP packets to send on failover event (int) parm: num_unsol_na:Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event (int) parm: miimon:Link check interval in milliseconds (int) parm: updelay:Delay before considering link up, in milliseconds (int) parm: downdelay:Delay before considering link down, in milliseconds (int) parm: use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default) (int) parm: mode:Mode of operation : 0 for balance-rr, 1 for active-backup, 2 for balance-xor, 3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, 6 for balance-alb (charp) parm: primary:Primary network device to use (charp) parm: lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast) (charp) parm: ad_select:803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2) (charp) parm: xmit_hash_policy:XOR hashing method: 0 for layer 2 (default), 1 for layer 3+4 (charp) parm: arp_interval:arp interval in milliseconds (int) parm: arp_ip_target:arp targets in n.n.n.n form (array of charp) parm: arp_validate:validate src/dst of ARP probes: none (default), active, backup or all (charp) parm: fail_over_mac:For active-backup, do not set all slaves to the same MAC. none (default), active or follow (charp) in /sys/module/bonding/parameters ls -l /sys/module/bonding/parameters/ total 0 -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_grat_arp -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_unsol_na I found some of this parameters under /sys/class/net/bond0/bonding/, but when i try to change one i got the following error echo layer2+3 > /sys/class/net/bond0/bonding/xmit_hash_policy -bash: echo: write error: Operation not permitted

    Read the article

  • BSOD Before Windows Will Loads - Graphics Related

    - by Brian
    Alright deep breath here: (Windows 7 Home Premium 64 bit btw) Today I installed Star Craft 2 Beta. After trying to log in, it had some issues where it said my device stopped working (referring to my video device I have to imagine). After I force quit the game there were some random "hot" (various colors if i remember correctly) pixels on the screen. I decided to reboot and try again with similar results. I figured that maybe my display drivers could stand to be updated (I don't frequently update them as I don't often run into problems). I went out to nVidia's website and grabbed the latest drivers for Windows 7 64 bit GeForce 9 series. (I have SLi-ed 9800 GTs). Everything seemed to install fine and I performed the restart. This is when things went from bad (can't play SC2 beta ;) ) to worse (can't boot into windows!). Initially the very first splash screen - I think it's the bios splash screen - had lines of colored pixels covering it. It then displayed a screen that had lots of "(" on it. After that it showed the normal windows 7 splash screen as if it were going to load into Windows. Before getting much further, it BSODed on me. It was a 0x0000003B stop error. At nvlddmkm.sys. A little digging let verified that this was a problem with an nVidia graphics device, not a real shocker. Windows decided it would try to help me diagnose the problem, which it's only answer to was a System Restore, which did nothing to alleviate the problem. I was able to boot up fine in safe mode and was not able to roll back the driver, however I did uninstall the driver and reboot. I still had the graphical anomalies during the first two screens (same colored "."'s and weird "("'s), but there was NOT a stop error. Windows loaded up, found a default driver for the device and installed it and I restarted to let it load - and had yet another BSOD Stop error. Repeat driver uninstall, this time I reloaded the same version (I think it's possible that I was running a 32 bit version or a vista versus windows 7 version, but I don't have that information handy) of the nVidia driver from their website. Restart, same anomalies, same Stop Error. I am at a loss - At this point all I can think is that the firmware for the Video cards got fried or there's actual damage to the cards which I sincerely hope is not the case but the sooner I know the better. Any insight into what I might be able to do to troubleshoot/fix this problem would be most helpful. Attached below is a dump from DxDiag. Please let me know if there is more info that I could provide. ------------------ System Information ------------------ Time of this report: 3/18/2010, 23:22:48 Machine name: BRIAN-PC Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600) (7600.win7_rtm.090713-1255) Language: English (Regional Setting: English) System Manufacturer: Dell Inc System Model: XPS 630i BIOS: Phoenix - AwardBIOS v6.00PG Processor: Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz (4 CPUs), ~2.3GHz Memory: 8192MB RAM Available OS Memory: 8190MB RAM Page File: 1855MB used, 14521MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found User DPI Setting: Using System DPI System DPI Setting: 96 DPI (100 percent) DWM DPI Scaling: Disabled DxDiag Version: 6.01.7600.16385 32bit Unicode DxDiag Previously: Crashed in DirectShow (stage 1). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information ------------ DxDiag Notes ------------ Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. -------------------- DirectX Debug Levels -------------------- Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) --------------- Display Devices --------------- Card name: Manufacturer: Chip type: DAC type: Device Key: Enum\ Display Memory: n/a Dedicated Memory: n/a Shared Memory: n/a Current Mode: 1600 x 1200 (32 bit) (1Hz) Driver Name: Driver File Version: () Driver Version: DDI Version: unknown Driver Model: unknown Driver Attributes: Final Retail Driver Date/Size: , 0 bytes WHQL Logo'd: n/a WHQL Date Stamp: n/a Device Identifier: {D7B70EE0-4340-11CF-B123-B03DAEC2CB35} Vendor ID: 0x0000 Device ID: 0x0000 SubSys ID: 0x00000000 Revision ID: 0x0000 Driver Strong Name: Unknown Rank Of Driver: Unknown Video Accel: Deinterlace Caps: n/a D3D9 Overlay: n/a DXVA-HD: n/a DDraw Status: Not Available D3D Status: Not Available AGP Status: Not Available ------------- Sound Devices ------------- Description: Speakers (Realtek High Definition Audio) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek Digital Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek HDMI Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No --------------------- Sound Capture Devices --------------------- Description: Microphone (Realtek High Definition Audio) Default Sound Capture: Yes Default Voice Capture: Yes Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 Description: Realtek Digital Input (Realtek High Definition Audio) Default Sound Capture: No Default Voice Capture: No Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 ------------------- DirectInput Devices ------------------- Device Name: Mouse Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: Keyboard Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: ESA FW Update Attached: 1 Controller ID: 0x0 Vendor/Product ID: 0x0955, 0x000A FF Driver: n/a Poll w/ Interrupt: No ----------- USB Devices ----------- + USB Root Hub | Vendor/Product ID: 0x10DE, 0x026D | Matching Device ID: usb\root_hub | Service: usbhub | +-+ USB Input Device | | Vendor/Product ID: 0x0955, 0x000A | | Location: Port_#0002.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant device | | | Vendor/Product ID: 0x0955, 0x000A | | | Matching Device ID: hid_device | | +-+ USB Input Device | | Vendor/Product ID: 0x046D, 0xC01E | | Location: Port_#0003.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant mouse | | | Vendor/Product ID: 0x046D, 0xC01E | | | Matching Device ID: hid_device_system_mouse | | | Service: mouhid ---------------- Gameport Devices ---------------- ------------ PS/2 Devices ------------ + Standard PS/2 Keyboard | Matching Device ID: *pnp0303 | Service: i8042prt | + Terminal Server Keyboard Driver | Matching Device ID: root\rdp_kbd | Upper Filters: kbdclass | Service: TermDD | + Terminal Server Mouse Driver | Matching Device ID: root\rdp_mou | Upper Filters: mouclass | Service: TermDD ------------------------ Disk & DVD/CD-ROM Drives ------------------------ Drive: C: Free Space: 324.3 GB Total Space: 608.4 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: D: Free Space: 1.0 GB Total Space: 2.0 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: E: Model: TSSTcorp DVD+-RW TS-H653F SCSI CdRom Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7600.16385 (English), , 0 bytes -------------- System Devices -------------- Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B7&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&18 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AF&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0A Driver: n/a Name: PCI standard host CPU bridge Device ID: PCI\VEN_10DE&DEV_03A3&SUBSYS_02491028&REV_A2\3&2411E6FE&1&00 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0267&SUBSYS_02491028&REV_A1\3&2411E6FE&1&78 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B6&SUBSYS_02491028&REV_A1\3&2411E6FE&1&10 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AE&SUBSYS_02491028&REV_A1\3&2411E6FE&1&09 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0272&SUBSYS_02491028&REV_A3\3&2411E6FE&1&52 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0266&SUBSYS_02491028&REV_A1\3&2411E6FE&1&70 Driver: n/a Name: LSI 1394 OHCI Compliant Host Controller Device ID: PCI\VEN_11C1&DEV_5811&SUBSYS_02491028&REV_70\4&14591D7E&0&2880 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B5&SUBSYS_02491028&REV_A1\3&2411E6FE&1&06 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AD&SUBSYS_02491028&REV_A1\3&2411E6FE&1&08 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0270&SUBSYS_02491028&REV_A2\3&2411E6FE&1&48 Driver: n/a Name: Standard Dual Channel PCI IDE Controller Device ID: PCI\VEN_10DE&DEV_0265&SUBSYS_02491028&REV_A1\3&2411E6FE&1&68 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&4BABE2A&0&0028 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B4&SUBSYS_02491028&REV_A1\3&2411E6FE&1&07 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&01 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_026F&SUBSYS_CB8410DE&REV_A2\3&2411E6FE&1&80 Driver: n/a Name: NVIDIA nForce PCI System Management Device ID: PCI\VEN_10DE&DEV_0264&SUBSYS_02491028&REV_A3\3&2411E6FE&1&51 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&10BD3C89&0&0018 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B3&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0E Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AB&SUBSYS_02491028&REV_A1\3&2411E6FE&1&04 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_10DE&DEV_026E&SUBSYS_02491028&REV_A3\3&2411E6FE&1&59 Driver: n/a Name: PCI standard ISA bridge Device ID: PCI\VEN_10DE&DEV_0260&SUBSYS_02491028&REV_A3\3&2411E6FE&1&50 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&11 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B2&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0D Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&02 Driver: n/a Name: Standard OpenHCD USB Host Controller Device ID: PCI\VEN_10DE&DEV_026D&SUBSYS_02491028&REV_A3\3&2411E6FE&1&58 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&12 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B1&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0C Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A9&SUBSYS_02491028&REV_A1\3&2411E6FE&1&03 Driver: n/a Name: High Definition Audio Controller Device ID: PCI\VEN_10DE&DEV_026C&SUBSYS_02491028&REV_A2\3&2411E6FE&1&81 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B8&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&28 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B0&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0B Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A8&SUBSYS_02491028&REV_A2\3&2411E6FE&1&05 Driver: n/a Name: NVIDIA nForce Networking Controller Device ID: PCI\VEN_10DE&DEV_0269&SUBSYS_02491028&REV_A3\3&2411E6FE&1&A0 Driver: n/a --------------- EVR Power Information --------------- Current Setting: {5C67A112-A4C9-483F-B4A7-1D473BECAFDC} (Quality) Quality Flags: 2576 Enabled: Force throttling Allow half deinterlace Allow scaling Decode Power Usage: 100 Balanced Flags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 50 PowerFlags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 0

    Read the article

  • Why isn't the scripts in my autoload folder being executed in Vim?

    - by Codemonkey
    I'm trying to use Pathogen to manage my Vim extensions. My bundle folder looks like this: .../bundle/ +-- vim-pathogen ¦   +-- autoload ¦   +-- pathogen.vim +-- vim-smoothscroll +-- autoload +-- smooth_scroll.vim And my vimrc file includes this: let s:root = fnamemodify(resolve(expand(":p")), ":h") " Initiate pathogen. exec "source " . s:root . "/vimfiles/bundle/vim-pathogen/autoload/pathogen.vim" exec pathogen#infect() My vimrc file is a symlink located in ~ but pointing to a folder inside my Dropbox folder. This appears to work when I start Vim. Pathogen has added vim-smoothscroll to my runtimepath: :set runtimepath? runtimepath=~/Dropbox/Personal/config_sync/vim/vimfiles,~/Dropbox/Personal/config_sync/vim/vimfiles/bundle/vim-p athogen,~/Dropbox/Personal/config_sync/vim/vimfiles/bundle/vim-smoothscroll,~/.vim,~/vim/share/vim/vimfiles,~/vim/ share/vim/vim74,~/vim/share/vim/vimfiles/after,~/.vim/after The problem is that the script smooth_scroll.vim hasn't been loaded: 1: ~/.vimrc 2: ~/Dropbox/Personal/config_sync/vim/vimfiles/bundle/vim-pathogen/autoload/pathogen.vim 3: ~/vim/share/vim/vim74/syntax/syntax.vim 4: ~/vim/share/vim/vim74/syntax/synload.vim 5: ~/vim/share/vim/vim74/syntax/syncolor.vim 6: ~/vim/share/vim/vim74/filetype.vim 7: ~/vim/share/vim/vim74/menu.vim 8: ~/vim/share/vim/vim74/autoload/paste.vim 9: ~/Dropbox/Personal/config_sync/vim/vimfiles/colors/codeschool.vim 10: ~/Dropbox/Personal/config_sync/vim/_vimrc_gui 11: ~/Dropbox/Personal/config_sync/vim/_vimrc_keybinds 12: ~/vim/share/vim/vim74/plugin/getscriptPlugin.vim 13: ~/vim/share/vim/vim74/plugin/gzip.vim 14: ~/vim/share/vim/vim74/plugin/matchparen.vim 15: ~/vim/share/vim/vim74/plugin/netrwPlugin.vim 16: ~/vim/share/vim/vim74/plugin/rrhelper.vim 17: ~/vim/share/vim/vim74/plugin/spellfile.vim 18: ~/vim/share/vim/vim74/plugin/tarPlugin.vim 19: ~/vim/share/vim/vim74/plugin/tohtml.vim 20: ~/vim/share/vim/vim74/plugin/vimballPlugin.vim 21: ~/vim/share/vim/vim74/plugin/zipPlugin.vim 22: ~/vim/share/vim/vim74/syntax/ruby.vim 23: ~/vim/share/vim/vim74/syntax/vim.vim 24: ~/vim/share/vim/vim74/syntax/python.vim Why is that? Loading the script manually works fine.

    Read the article

  • Query Execution Failed in Reporting Services reports

    - by Chris Herring
    I have some reporting services reports that talk to Analysis Services and at times they fail with the following error: An error occurred during client rendering. An error has occurred during report processing. Query execution failed for dataset 'AccountManagerAccountManager'. The connection cannot be used while an XmlReader object is open. This occurs sometimes when I change selections in the filter. It also occurs when the machine has been under heavy load and then will consistently error until SSAS is restarted. The log file contains the following error: processing!ReportServer_0-18!738!04/06/2010-11:01:14:: e ERROR: Throwing Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Query execution failed for dataset 'AccountManagerAccountManager'., ; Info: Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Query execution failed for dataset 'AccountManagerAccountManager'. ---> System.InvalidOperationException: The connection cannot be used while an XmlReader object is open. at Microsoft.AnalysisServices.AdomdClient.XmlaClient.CheckConnection() at Microsoft.AnalysisServices.AdomdClient.XmlaClient.ExecuteStatement(String statement, IDictionary connectionProperties, IDictionary commandProperties, IDataParameterCollection parameters, Boolean isMdx) at Microsoft.AnalysisServices.AdomdClient.AdomdConnection.XmlaClientProvider.Microsoft.AnalysisServices.AdomdClient.IExecuteProvider.ExecuteTabular(CommandBehavior behavior, ICommandContentProvider contentProvider, AdomdPropertyCollection commandProperties, IDataParameterCollection parameters) at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.System.Data.IDbCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.ReportingServices.DataExtensions.AdoMdCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.ReportingServices.OnDemandProcessing.RuntimeDataSet.RunDataSetQuery() Can anyone shed light on this issue?

    Read the article

  • Why does traceroute take much longer than ping?

    - by PHP
    How to explain this? C:\Documents and Settings\Administrator>tracert google.com Tracing route to google.com [64.233.189.104] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.0.1 2 7 ms <1 ms <1 ms reserve.cableplus.com.cn [218.242.223.209] 3 108 ms 135 ms 163 ms 211.154.70.10 4 * * * Request timed out. 5 2 ms * 1 ms 211.154.64.114 6 1 ms 1 ms 1 ms 211.154.72.185 7 1 ms 1 ms 1 ms 202.96.222.77 8 2 ms 1 ms 2 ms 61.152.81.145 9 1 ms 2 ms 1 ms 61.152.86.54 10 1 ms 1 ms 1 ms 202.97.33.238 11 2 ms 2 ms 2 ms 202.97.33.54 12 2 ms 1 ms 2 ms 202.97.33.5 13 33 ms 33 ms 33 ms 202.97.61.50 14 34 ms 34 ms 34 ms 202.97.62.214 15 34 ms 186 ms 37 ms 209.85.241.56 16 35 ms 35 ms 44 ms 66.249.94.34 17 34 ms 34 ms 34 ms hkg01s01-in-f104.1e100.net [64.233.189.104] Trace complete. So average time should be :1+7+108+2+1+1+2+1+1+2+2+33+34+34+35+34+34+35+34,which is a lot bigger than ping C:\Documents and Settings\Administrator>ping google.com Pinging google.com [64.233.189.104] with 32 bytes of data: Reply from 64.233.189.104: bytes=32 time=34ms TTL=241 Reply from 64.233.189.104: bytes=32 time=34ms TTL=241 Reply from 64.233.189.104: bytes=32 time=34ms TTL=241 Reply from 64.233.189.104: bytes=32 time=34ms TTL=241 Ping statistics for 64.233.189.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 34ms, Maximum = 34ms, Average = 34ms

    Read the article

  • ASP.NET AJAX, WebSeal Junctions, and Sessions

    - by powella
    I've run up across a problem with ASP.NET AJAX (hooked up to WebServices directly) and accessing our site through a WebSeal junction. Listing 11. On this page; http://www.ibm.com/developerworks/tivoli/library/t-ajaxtam/index.html explains that requests to pages which do not result in a content type of text/html are not sent with cookie data. Hence, no session. ASP.NET AJAX requests are returned with a content type of "application/json; charset=utf-8". As such, the WebSeal junction is not appending the Session Cookie to the request. This results in our WebService seeing the user as invalid, due to no session information. The Junction has been setup properly with the -J parameter (thats an uppercase J, which appends the required script for WebSeal to the bottom of the page - this prevents forcing IE into quirks mode.) and we've confirmed that the necessary script exists in the output source. I'm up for any suggestions at this point, as I'm out of ideas. FWIW, the site runs perfectly when not accessed through the WebSeal Junction.

    Read the article

  • Centos CMake Does Not Install Using gcc 4.7.2

    - by Devin Dixon
    A similar problem has been reported here with no solution:https://www.centos.org/modules/newbb/print.php?form=1&topic_id=42696&forum=56&order=ASC&start=0 I've added and upgraded gcc to centos cd /etc/yum.repos.d wget http://people.centos.org/tru/devtools-1.1/devtools-1.1.repo yum --enablerepo=testing-1.1-devtools-6 install devtoolset-1.1-gcc devtoolset-1.1-gcc-c++ scl enable devtoolset-1.1 bash The result is this for my gcc [root@hhvm-build-centos cmake-2.8.11.1]# gcc -v Using built-in specs. COLLECT_GCC=gcc COLLECT_LTO_WRAPPER=/opt/centos/devtoolset-1.1/root/usr/libexec/gcc/x86_64-redhat-linux/4.7.2/lto-wrapper Target: x86_64-redhat-linux Configured with: ../configure --prefix=/opt/centos/devtoolset-1.1/root/usr --mandir=/opt/centos/devtoolset-1.1/root/usr/share/man --infodir=/opt/centos/devtoolset-1.1/root/usr/share/info --with-bugurl=http://bugzilla.redhat.com/bugzilla --enable-bootstrap --enable-shared --enable-threads=posix --enable-checking=release --disable-build-with-cxx --disable-build-poststage1-with-cxx --with-system-zlib --enable-__cxa_atexit --disable-libunwind-exceptions --enable-gnu-unique-object --enable-linker-build-id --enable-languages=c,c++,fortran,lto --enable-plugin --with-linker-hash-style=gnu --enable-initfini-array --disable-libgcj --with-ppl --with-cloog --with-mpc=/home/centos/rpm/BUILD/gcc-4.7.2-20121015/obj-x86_64-redhat-linux/mpc-install --with-tune=generic --with-arch_32=i686 --build=x86_64-redhat-linux Thread model: posix gcc version 4.7.2 20121015 (Red Hat 4.7.2-5) (GCC) And I tried to then install cmake through http://www.cmake.org/cmake/resources/software.html#latest But I keep running into this error: Linking CXX executable ../bin/ccmake /opt/centos/devtoolset-1.1/root/usr/libexec/gcc/x86_64-redhat-linux/4.7.2/ld: CMakeFiles/ccmake.dir/CursesDialog/cmCursesMainForm.cxx.o: undefined reference to symbol 'keypad' /opt/centos/devtoolset-1.1/root/usr/libexec/gcc/x86_64-redhat-linux/4.7.2/ld: note: 'keypad' is defined in DSO /lib64/libtinfo.so.5 so try adding it to the linker command line /lib64/libtinfo.so.5: could not read symbols: Invalid operation collect2: error: ld returned 1 exit status gmake[2]: *** [bin/ccmake] Error 1 gmake[1]: *** [Source/CMakeFiles/ccmake.dir/all] Error 2 gmake: *** [all] Error 2 The problem seems to come from the new gcc installed because it works with the default install. Is there a solution to this problem?

    Read the article

  • Ubuntu 12.04 LDAP SSL self-signed cert not accepted

    - by MaddHacker
    I'm working with Ubuntu 12.04, using OpenLDAP server. I've followed the instructions on the Ubuntu help pages and can happily connect without security. To test my connection, I'm using ldapsearch the command looks like: ldapsearch -xv -H ldap://ldap.[my host].local -b dc=[my domain],dc=local -d8 -ZZ I've also used: ldapsearch -xv -H ldaps://ldap.[my host].local -b dc=[my domain],dc=local -d8 As far as I can tell, I've setup my certificate correctly, but no matter why I try, I can't seem to get ldapsearch to accept my self-signed certificate. So far, I've tried: Updating my /etc/ldap/ldap.conf file to look like: BASE dc=[my domain],dc=local URI ldaps://ldap.[my host].local TLS_CACERT /etc/ssl/certs/cacert.crt TLS_REQCERT allow Updating my /etc/ldap.conf file to look like: base dc=[my domain],dc=local uri ldapi:///ldap.[my host].local uri ldaps:///ldap.[my host].local ldap_version 3 ssl start_tls ssl on tls_checkpeer no TLS_REQCERT allow Updating my /etc/default/slapd to include: SLAPD_SERVICES="ldap:/// ldapi:/// ldaps:///" Several hours of Googling, most of which resulted in adding the TLS_REQCERT allow The exact error I'm seeing is: ldap_initialize( ldap://ldap.[my host].local ) request done: ld 0x20038710 msgid 1 TLS certificate verification: Error, self signed certificate in certificate chain TLS: can't connect. ldap_start_tls: Connect error (-11) additional info: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed After several hours of this, I was hoping someone else has seen this issue, and/or knows how to fix it. Please do let me know if I should add more information, or if you need further data.

    Read the article

  • Ext3 fs: Block bitmap for group 1 not in group (block 0). is fs dead?

    - by ip
    Hi, My company has a server with one big partition with Mysql database and php files. Now this partition seems to be corrupted, as reported from kernel messages when I tried to mount it manually: [329862.817837] EXT3-fs error (device loop1): ext3_check_descriptors: Block bitmap for group 1 not in group (block 0)! [329862.817846] EXT3-fs: group descriptors corrupted! I've tried to recovery it running tools from a PLD livecd. These are the tools I have tested: - e2retrieve - testdisk - photorec - dd_rescue/dd_rhelp - ddrescue - fsck.ext2 - e2salvage without any success. dumpe2fs 1.41.3 (12-Oct-2008) Filesystem volume name: /dev/sda3 Last mounted on: <not available> Filesystem UUID: dd51610b-6de0-4392-a6f3-67160dbc0343 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal filetype sparse_super Default mount options: (none) Filesystem state: not clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 9502720 Block count: 18987570 Reserved block count: 949378 Free blocks: 11555345 Free inodes: 11858398 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 16384 Inode blocks per group: 512 Last mount time: Wed Mar 24 09:31:03 2010 Last write time: Mon Apr 12 11:46:32 2010 Mount count: 10 Maximum mount count: 30 Last checked: Thu Jan 1 01:00:00 1970 Check interval: 0 (<none>) Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 128 Journal inode: 8 Journal backup: inode blocks dumpe2fs: A block group is missing an inode table while reading journal inode There's any other tools I have to test before considering these disk definitely unrecoverable? Many thanks, ip

    Read the article

  • Where can I find linux-kernel-headers-x.x.x.x for SUSE?

    - by Landy
    I'm installing VMware Workstation on a SLED 11 SP1, and the installation is blocked by an error message "Kernel headers for version 2.6.32.27-0.2-default were not found". If you installed them in a non-default path you can specify the path below. Otherwise refer to your distribution's documentation for installation instructions and click Refresh to search again in default locations. The output of rpm -qa | grep kernel is kernel-default-2.6.32.27-0.2.2 kernel-default-base-2.6.32.27-0.2.2 linux-kernel-headers-2.6.32-1.4.13 kernel-default-extra-2.6.32.27-0.2.2 nfs-kernel-server-1.2.1-2.10.1 I had met this issue in Ubuntu and I installed the required linux header via apt-get then the issue disappeared. But in SLED, I didn't find the rpm package in SUSE's software repository, and I also google "linux-kernel-headers-2.6.32.27" but did not match any documents. Any suggestion will be highly appreciated. Thanks. The output result of zypper se kernel | grep kernel is i | linux-kernel-headers | Linux Kernel Headers | package | linux-kernel-headers | Linux Kernel Headers | srcpackage

    Read the article

  • VSS Post Backup failures for Virtual Server 2005 R2 SP1 virtual machines

    - by califguy4christ
    We've been seeing strange errors with Volume Shadow Copy services on our Virtual Server 2005 R2 SP1 host. It appears to be failing on a strange mountpoint in the C:\WINDOWS\Temp\ folders, which I believe is used by VSS to mount a writeable image file. To summarize: The Microsoft Virtual Server 2005 Writer continually goes into a failed retryable state The Virtual Server log reports errors during the Post Backup phase VSS reports errors backing up a mount point of unknown origins The mount point causes NTFS and ftdisk errors The host is x86 Windows Server 2003 Standard, SP2. The virtual machine is the same. Both use basic disks. Here is the writer state: Writer name: 'Microsoft Virtual Server 2005 Writer' Writer Id: {76afb926-87ad-4a20-a50f-cdc69412ddfc} Writer Instance Id: {78df98e2-bf19-4804-890b-15865efef3bd} State: [11] Failed Last error: Retryable error From the Virtual Server log: Virtual Server - Vss Writer - Event ID: 1035: The VSS writer for Virtual Server failed during the PostBackup phase. The guest shadow copies did not get exposed on the host machine, after mounting all the virtual hard disks of the virtual machine VMACHINE. From the Application log: VSS - None - Event ID: 12290: Volume Shadow Copy Service warning: GetVolumeInformationW( \\?\Volume{fb84bae7-87f5-11dd-9832-001cc4961ca6}\,NULL,0, NULL,NULL,[0x00000000], , 260) == 0x0000045d. hr = 0x00000000. From the System log: Ntfs - Disk - Event ID: 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:\WINDOWS\Temp\ {fb84bae7-87f5-11dd-9832-001cc49.... My current theory is that VSS creates a mount point for an image file of the VHD, then the software panics for some reason, leaving everything in an inconsistent state. Removing the mount point doesn't resolve the problem. All of the other disks check out fine with CHKDSK. There's no exclusion option for VHDs or to turn off online backups. Has anyone seen this kind of thing before or point me in the right direction for getting more information about the mount point and it's origins? I haven't been able to trace what application is creating that mount point.

    Read the article

  • Prosody mod auth external not working

    - by Yang
    I installed mod_auth_external for 0.8.2 on ubuntu 12.04 but it's not working. I have external_auth_command = "/home/yang/chat/testing" but it's not getting invoked. I enabled debug logging and see no messages from that mod. Any help? I'm using the Candy example client. Here's what's written to the log after I submit a login request (and nothing in err log): Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40527 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: %s) Oct 24 21:02:43 boshb344ba85-fbf5-4a26-b5f5-5bd35d5ed372 debug BOSH session created for request from 169.254.11.255 Oct 24 21:02:43 mod_bosh info New BOSH session, assigned it sid 'b344ba85-fbf5-4a26-b5f5-5bd35d5ed372' Oct 24 21:02:43 httpserver debug Sending response to bf9120 Oct 24 21:02:43 httpserver debug Destroying request bf9120 Oct 24 21:02:43 httpserver debug Request has destroy callback Oct 24 21:02:43 socket debug server.lua: closed client handler and removed socket from list Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 0 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40528 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: b344ba85-fbf5-4a26-b5f5-5bd35d5ed372) Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 1 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 mod_bosh debug Have nothing to say, so leaving request unanswered for now Oct 24 21:02:43 httpserver debug Request c295d0 left open, on_destroy is function(mod_bosh.lua:81) Here's the config I added: modules_enabled = { ... "bosh"; -- Enable BOSH clients, aka "Jabber over HTTP" ... } authentication = "external" external_auth_protocol = "generic" external_auth_command = "/home/yang/chat/testing"

    Read the article

  • Scripting an automated SQLServer 2008 DR move

    - by ItsAMystery
    Hi All We use the built in logshipping in SQLServer to logship to our DR site but once in a month do a DR test which requires us to move back and forth between our Live and BAckup servers. We run multiple (30) databases on the system so manually backing up the final logs and disabling the jobs is too much work and takes too long. I though no problem, I will script it but have run into trouble with it always complaninig that the final logship is too early to apply even though I dont export the final log until putting the database into norecovery mode. Firstly, does any one no a simple and reliable way of doing this? I have lokoed at some 3rd party software (redgate sqlbackup I think it was) but that didnt make it easy in this situation either. What I want to be able to do is basically run a script (a series of stored procedures) to get me to DR and run another to get me back with no dataloss. My scripts are very simplistic at the moment but here they are: 2 servers Primary Paris Secondary ParisT The StartAgentJobAndWait is a script written by someone else (ta) and just checks the jobs have finished or quits it if it never ends. At the moment I am just using a test database called BOB2 but if I can get it working will pass in the database and job names. from PARIS: /* Disable backup job */ exec msdb..sp_update_job @job_name = 'LSBackup_BOB2', @enabled = 0 exec PARIST.msdb..sp_update_job @job_name = 'LSCopy_PARIS_BOB2', @enabled = 0 exec PARIST.msdb..sp_update_job @job_name = 'LSRestore_PARIS_BOB2', @enabled = 0 exec PARIST.master.dbo.DRStage2 ParisT DRStage2 DECLARE @RetValue varchar (10) EXEC @RetValue = StartAgentJobAndWait LSCopy_PARIS_BOB2 , 2 SELECT ReturnValue=@RetValue if @RetValue = 1 begin print 'The Copy Task completed Succesffuly' END ELSE print 'The Copy task failed, This may or may not be a problem, check restore state of database' SELECT @RetValue = 0 EXEC @RetValue = StartAgentJobAndWait LSRestore_PARIS_BOB2 , 2 SELECT ReturnValue=@RetValue if @RetValue = 1 begin print 'The Restore Task completed Succesffuly' END ELSE print 'The Copy task failed, This may or may not be a problem, check restore state of database' exec PARIS.master.dbo.DRStage3 /* Do the last logship and move it to Trumpington */ BACKUP log "BOB2" to disk='c:\drlogshipping\BOB2.bak' with compression, norecovery EXEC xp_cmdshell 'copy c:\drlogshipping \\192.168.7.11\drlogshipping' EXEC PARIST.master.dbo.DRTransferFinish AS BEGIN restore database "BOB2" from disk='c:\drlogshipping\bob2.bak' with recovery

    Read the article

  • AWStats consumes too much resource, how to disable temporarily

    - by trante
    For some days AWStats takes %10-%20 of my CPU, takes 400-550 MB RAM and works for hours. Maybe my site's traffic became larger so process time takes more time than before or some bugs in program makes this. Anyway I want to disable AWStats temporarily. Maybe I would want to activate it in future. I found that answer. But it gives commands to remove AWStats. I only want to disable it temporarily. My system is Centos 6.3, Plesk 11.5.30 Update #19. I tried to disable cron jobs. I run this # killall awstats.pl I opened # vi /etc/cron.daily/awstats file and I changed it to this: #!/bin/sh #/usr/share/awstats/awstats_updateall.pl now -awstatsprog=/var/www/cgi-bin/awstats/awstats.pl -configdir=/etc/awstats >/dev/null 2>&1 exit 0 After some time I still see that awstats is running. What should I do more to not to awstats run again ? But without removing my files. After changing " /etc/cron.daily/awstats" file awstats doesn't start in daytime. But every night in 03:15 awstats starts again. Because of Plesk auto updates are working at that time, I changed from Plesk. Don't auto update automatically. But it seems like last night at 03:15 awstats started again. Is there any way to stop awstats temporarily except this solution ? Because this solution deletes awstats configs permanently and I don't know how to revert it back in future ? Turn off all AWStats for Plesk 11+ domains #!/bin/bash for i in /var/www/vhosts/*; do echo "Turning off and deleting Stats for" echo `basename $i` /usr/local/psa/admin/bin/webstatmng --unset-configs --stat-prog=awstats --domain-name=`basename $i` /usr/local/psa/admin/bin/webstatmng --clean --stat-prog=awstats --domain-name=`basename $i` done

    Read the article

  • Office Communicator and cannot sync Address book error

    - by Noah
    We are trying to get OCS 2007 R2 up and running. The clients login fine, but when I let it sit for a while, we still get the address book sync error message of: "Cannot synchronize with the corporate address book. This may be because the proxy server setting in your web browser does not allow access to the address book. If the problem persists, contact your system administrator". When I try and download the file locally, this error comes up: Could not load file or assembly 'ABServerHttpHandler, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. Failed to grant minimum permission requests. (Exception from HRESULT: 0x80131417) I googled and came across this post (http://social.technet.microsoft.com/Forums/en/ocsaddressbook/thread/c28ff2d8-66a4-456c-a5ad-e445a667e8ed) which suggests removing and reinstalling .NET 2.0 but that didn't seem to resolve the issue either. When we run abserver.exe -validateDB it works properly. We even tried the suggestion from Greg's Blog (http://blogs.technet.com/greganth/archive/2009/03/11/office-communicator-notifications-cannot-synchronize-address-book.aspx) about restarting the web component services but that didn't work either. Still seeing the same issue. So does anyone have an idea of where we go from here?

    Read the article

  • gzip specific files

    - by byTheDrop
    for some reason these files are not gzipping on my apache server, chrome network tab shows this. Is there a specific directive I can add to htaccess to cache these files? Compressing the following resources with gzip could reduce their transfer size by about two thirds (~680.45KB): adae8bc4c3cb52cbe22358aaced87a72.css could save ~607B css_f91fa8d73b5e7661d6dcf9e58395e533.css could save ~59.54KB jquery.min.js could save ~37.27KB drupal.js could save ~6.15KB auto_image_handling.js could save ~6.72KB lightbox.js could save ~29.38KB superfish.js could save ~2.42KB jquery.bgiframe.min.js could save ~1011B jquery.hoverIntent.minified.js could save ~1.05KB nice_menus.js could save ~581B panels.js could save ~531B jquery.pngFix.js could save ~2.98KB jquery.cycle.all.min.js could save ~20.20KB views_slideshow.js could save ~8.76KB views_slideshow.js could save ~9.02KB wanderlust_custom_videos.js could save ~598B wl_helper.js could save ~777B extlink.js could save ~2.88KB cufon-yui.js could save ~11.89KB googleanalytics.js could save ~1.48KB swfobject.js could save ~6.65KB jquery.jcarousel.min.js could save ~10.19KB jcarousel.js could save ~6.01KB Akzidenz_Grotesk_BE_Super_800.font.js could save ~14.27KB Akzidenz_Grotesk_BE_Bold_700.font.js could save ~12.96KB Akzidenz_Grotesk_BE_Cn_400.font.js could save ~13.39KB SuperCondensed_500.font.js could save ~24.40KB FuturaBold_700.font.js could save ~26.19KB Futura_500.font.js could save ~57.70KB SuperGroteskB_500.font.js could save ~23.86KB jquery.cookie.js could save ~1.25KB wanderlust.js could save ~1.69KB sliderbottom.js could save ~442B jcarousellite_1.0.1.min.js could save ~4.60KB jcarousellite_control.js could save ~224B sitesdropdown.js could save ~1.09KB widgets.js could save ~50.13KB cufon-drupal.js could save ~599B swfobject_api.js could save ~348B ga.js could save ~24.02KB all.js could save ~124.67KB tweet_button.1347008535.html could save ~38.43KB xd_arbiter.php could save ~16.80KB xd_arbiter.php could save ~16.80KB

    Read the article

  • Can't compile CentOS 5, Ruby 1.9.2 and OpenSSL 1.0.0c

    - by pstinnett
    I'm trying to install Ruby 1.9.2 on CentOS 5.5. I get through most of the make process, but when it tries to compile OpenSSL I get an error. Below is the errror outputted: compiling openssl make[1]: Entering directory `/sources/ruby-1.9.2-p136/ext/openssl' gcc -I. -I../../.ext/include/x86_64-linux -I../.././include -I../.././ext/openssl -DRUBY_EXTCONF_H=\"extconf.h\" -fPIC -O3 -ggdb -Wextra -Wno-unused-parameter -Wno-parentheses -Wpointer-arith -Wwrite-strings -Wno-missing-field-initializers -Wno-long-long -o ossl_x509.o -c ossl_x509.c In file included from ossl.h:201, from ossl_x509.c:11: openssl_missing.h:71: error: conflicting types for ‘HMAC_CTX_copy’ /usr/include/openssl/hmac.h:102: error: previous declaration of ‘HMAC_CTX_copy’ was here openssl_missing.h:95: error: conflicting types for ‘EVP_CIPHER_CTX_copy’ /usr/include/openssl/evp.h:459: error: previous declaration of ‘EVP_CIPHER_CTX_copy’ was here make[1]: *** [ossl_x509.o] Error 1 make[1]: Leaving directory `/sources/ruby-1.9.2-p136/ext/openssl' make: *** [mkmain.sh] Error 1 Any help would be greatly appreciated! I'm not a master at Linux by any means, but I was able to successfully install this version of Ruby on our dev server. Our live server is running a newer version of OpenSSL which I'm assuming is why it's breaking. Just not sure what the fix is!

    Read the article

  • What is causing random hard freezes on my system? Kaspersky?

    - by Christian Ivicevic
    The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

    Read the article

  • Malware Cross Site Scriptinig attack / XSS Attack?

    - by user124176
    I have been hit by an Cross Site Scripting / XSS / RFI Attack, where I cant find it anywhere in the source of the files and Hashes on files have not been changed according to OSSEC HIDS that I run real time monitoring on all webdirs. The Attack happens on IE9 Only it and appends java script code like beneath, notice that it starts after /html tag closes normally. : scXXpt language="javascXXpt"var enuwjo = function(gqumas, yhxxju, zbkpilf, xzzvhld){var xew = function(iso) {var crh, eaq, i; var owb=""; crh = iso.length; for (i = 0; i < crh; ++i) {eaq = iso.charCodeAt(i)-2;owb = owb + String.fromCharCode(eaq);} return(owb); } var janlq=document.createElement(xew("crrngv"));janlq.setAttribute(xew("eqfg"), xew(gqumas));janlq.setAttribute(xew("ctejkxg"), xew("jvvr<11"+yhxxju));janlq.setAttribute(xew("ykfvj"), "1");janlq.setAttribute(xew("jgkijv"), "1");var lgtwyi=document.createElement(xew("rctco"));lgtwyi.setAttribute(xew("pcog"),xew(zbkpilf));lgtwyi.setAttribute(xew("xcnwg"),xew(xzzvhld));janlq.appendChild(lgtwyi);document.body.appendChild(janlq); } ; enuwjo("vxfgwtogg0dcrcmnwe0encuu","g{g0o{yge{0kp129;5","mlit{ttmdttponfhrrexihpe","fh;ccfe:85:5d9872;2;f569276h5268ff9;34:25;7d:8:7h8c68777;;822c73"); No code has been changed on file as far as my HIDS says ... but I can see in my Error log, the following... File does not exist: /var/www/vhosts/superkids.dk/ggtest/tvdeurmee In the Access log, the following IP - - [09/Jun/2012:23:30:13 +0200] "GET /tvdeurmee/bapakluc.class HTTP/1.1" 404 504 "-" "Mozilla/4.0 (Windows 7 6.1) Java/1.7.0_04" IP - - [09/Jun/2012:23:30:13 +0200] "GET /tvdeurmee/bapakluc/class.class HTTP/1.1" 404 509 "-" "Mozilla/4.0 (Windows 7 6.1) Java/1.7.0_04" Now... the folder or path /tvdeurmee/bapakluc/ does not exist on the server in question, nor does the Java Class class.class, yet it still looks like an local call to the server and it was getting an "404 File not found / 504 Gateway Timeout" (attack was blocked by local machine, hence the timeout / not found) Any idea on how to prevent the attack ? Im working on using HTML Purifier, but that might not be the correct idea it seems, according to some replies im getting on their forum :) Kind regards, Steven

    Read the article

  • How do I enable the confluence-users group?

    - by M. Joanis
    I've got an issue with Atlassian Confluence. Normal users can't log in, but administrators can... Details below! I manage users using an Apple Open Directory (LDAP). I created two groups: "confluence-administrators" and "confluence-users". I've added team leaders and managers to both groups, and I've added some users to "confluence-users". Everyone in "confluence-administrators" can log in easily. People in "confluence-users" can't log in at all. When I look at the user list (in Confluence), and select a user to examine the list of groups he or she belongs to, I can see that the Confluence Administrators are indeed members of the "confluence-administrators" group, but not a single user is a member of the "confluence-users" group. Not event the Confluence Administrators, which are members of both groups! So I tried to have one of the "confluence-users" log in while watching the Confluence logs. Here's the result: 2012-07-05 14:50:19,698 ERROR [http-8090-11] [core.event.listener.AutoGroupAdderListener] handleEvent Could not auto add user to group: Group <confluence-users> is read-only and cannot be updated at com.atlassian.crowd.directory.DbCachingRemoteDirectory.addUserToGroup(DbCachingRemoteDirectory.java:461) ... So it says the group group is read-only... I'm not sure why it is a problem. Well confluence-administrators too is read-only and it doesn't complain. Some things I don't think are part of the problem: I've synchronized Confluence with LDAP many, many times. I have verified many times that I didn't make a typo while setting the groups on the LDAP server. LDAP synchronization goes well. No errors in the logs (only INFO level log messages). The user exists. Errors in the logs are different when a user doesn't exist. Any help is most welcome!

    Read the article

  • authbind, privbind or iptables REDIRECT (port 80 to 8080)?

    - by chris_l
    Hi, I'd like to run Glassfish v3 as a non-privileged user on Linux (Debian), but make it available on port 80. I'm currently doing this with iptables: iptables -t nat -I PREROUTING -p tcp -d x.x.x.x --dport 80 -j REDIRECT --to-port 8080 This works, but I wonder: If this has any significant performance impact compared to binding directly to port 80 If I could make a similar setup also work for HTTPS (or if that must run on 443) If there's a way to avoid other users from binding to port 8080 (in case my server crashes) - maybe block that port permanently to other users somehow? ...or if I should use authbind/privbind instead? Problem: I couldn't make it work with authbind or privbind so far. For authbind, I edited asadmin's last line to: exec authbind --deep "$JAVA" -Djava.net.preferIPv4Stack=true -jar ... For privbind: exec privbind -u glassfish "$JAVA" -Djava.net.preferIPv4Stack=true -jar ... (Only) with these settings, I can successfully perform a create-domain --domainport 80. This proves, that authbind and privbind actually work (the authbind version of the script is called by the glassfish user; the privbind version is called by root of course). However, in both cases I get the following exception, when starting the domain (start-domain): [#|2010-03-20T13:25:21.925+0100|SEVERE|glassfishv3.0|javax.enterprise.system.core.com.sun.enterprise.v3.server|_ThreadID=11;_ThreadName=FelixStartLevel;|Shutting down v3 due to startup exception : Permission denied: 80=com.sun.enterprise.v3.services.impl.monitor.MonitorableSelectorHandler@1fc25e5|#] I haven't found a solution for that yet (after searching the web, it seems, that this isn't so easy?) But maybe, the solution with iptables is good enough - what do you think? Thanks, Chris

    Read the article

  • User can't SFTP after chroot

    - by Dauntless
    Ubuntu 10.04.4 LTS I'm trying to chroot the user 'sam'. According to all the tutorials out there this should work, but apparently I'm still doing something wrong. The user: sam:x:1005:1006::/home/sam:/bin/false I changed /etc/ssh/sshd_config like this (at the bottom of the file): #Subsystem sftp /usr/lib/openssh/sftp-server # CHROOT JAIL Subsystem sftp internal-sftp Match group users ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I added sam to the users group: $groups sam sam : sam users I changed the permissions for sam's home folder: $ ls -la /home/sam drwxr-xr-x 11 root root 4096 Sep 23 16:12 . drwxr-xr-x 8 root root 4096 Sep 22 16:29 .. drwxr-xr-x 2 sam users 4096 Sep 23 16:10 awstats drwxr-xr-x 3 sam users 4096 Sep 23 16:10 etc ... drwxr-xr-x 2 sam users 4096 Sep 23 16:10 homes drwxr-x--- 3 sam users 4096 Sep 23 16:10 public_html I restarted ssh and now sam can't log in with SFTP. The session is created, but also closed immediately: Sep 24 12:55:15 ... sshd[9917]: Accepted password for sam from ... Sep 24 12:55:15 ... sshd[9917]: pam_unix(sshd:session): session opened for user sam by (uid=0) Sep 24 12:55:16 ... sshd[9928]: subsystem request for sftp Sep 24 12:55:17 ... sshd[9917]: pam_unix(sshd:session): session closed for user sam Cyberduck says Unexpected end of sftp stream. and other clients give similar errors. What did I forget / what is going wrong? Thanks!

    Read the article

  • Ingress filtering in Linux traffic control: Redirect traffic to IFB device

    - by Dani Camps
    I have an openwrt router and I want to shape incoming traffic in order to classify all the traffic addressed to a certain IP address in my home network as low priority. For that purpose I want to redirect all traffic incoming to the eth1 interface, the one connected to the DSL modem, to an IFB device where I will do the shaping. These are the details of my system: Linux OpenWrt 2.6.32.27 #7 Fri Jul 15 02:43:34 CEST 2011 mips GNU/Linux Here is the script I am using where the last instruction is failing: # Variable definition ETH=eth1 IFB=ifb1 IP_LP="192.168.1.22/32" DL_RATE="900kbps" HP_RATE="890kbps" LP_RATE="10kbps" TC="tc" # Configuring the ifbX interface insmod ifb insmod sch_htb insmod sch_ingress ifconfig $IFB up # Adding the HTB scheduler to the ingress interface $TC qdisc add dev $IFB root handle 1: htb default 11 # Set the maximum bandwidth that each priority class can get, and the maximum borrowing they can do $TC class add dev $IFB parent 1:1 classid 1:10 htb rate $LP_RATE ceil $DL_RATE $TC class add dev $IFB parent 1:1 classid 1:11 htb rate $HP_RATE ceil $DL_RATE # Redirect all ingress traffic arriving at $ETH to $IFB $TC qdisc del dev $ETH ingress 2>/dev/null $TC qdisc add dev $ETH ingress $TC filter add dev $ETH parent ffff: protocol ip prio 1 u32 \ match u32 0 0 flowid 1:1 \ action mirred egress redirect dev $IFB The last instruction fails with: Action 4 device ifb1 ifindex 9 RTNETLINK answers: No such file or directory We have an error talking to the kernel Does anyone know what am I doing wrong ? Best Regards Daniel

    Read the article

  • Configure ApacheDS 1.5 with accessControlEnabled=true for authenticated access

    - by cmyers
    I need to set up an apacheDS instance. I am using standalone 1.5.5 on Linux. I have removed the example partition and added two of my own, each with their own suffixes. I have imported LDIFs for the two partitions and everything looks correct data-wise. I need to configure ApacheDS to disallow anonymous access. I was able to do that by following some of the directions here: http://directory.apache.org/apacheds/1.5/145-enable-and-disable-anonymous-access.html http://directory.apache.org/apacheds/1.5/32-basic-authorization.html Now only the administrator account (uid=admin,ou=system) can log in and make queries. I need to establish an admin account, and a "regular user" account which can read and write only certain entries within each partition. I tried to read the above docs and I got nuthin'. The second page "basic authorization" is completely incomprehensible to me. When I tried to add a "prescriptiveACI" to it using Apache Directory Studio, I get: Administration point 2.5.4.11=abc,2.5.4.10=efg does not contain an administrativeRole attribute! An administrativeRole attribute in the administrative point is required to add a subordinate subentry. where my partition is "ou=abc,o=def". I have no clue what is going on and the docs are really not helping, I am at a complete loss here. How can it possibly be this hard to just restrict access? P.S. can someone with proper rep please change the tag "apache" to the new tag "ApacheDS"?

    Read the article

  • unreadable corrupted ntfs partition - lost clusters reported

    - by Eduardo Martinez
    partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

    Read the article

< Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >