Search Results

Search found 17795 results on 712 pages for 'tab management'.

Page 283/712 | < Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >

  • RAID Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • Firewall for internal networks

    - by Cylindric
    I have a virtualised infrastructure here, with separated networks (some physically, some just by VLAN) for iSCSI traffic, VMware management traffic, production traffic, etc. The recommendations are of course to not allow access from the LAN to the iSCSI network for example, for obvious security and performance reasons, and same between DMZ/LAN, etc. The problem I have is that in reality, some services do need access across the networks from time to time: System monitoring server needs to see the ESX hosts and the SAN for SNMP VSphere guest console access needs direct access to the ESX host the VM is running on VMware Converter wants access to the ESX host the VM will be created on The SAN email notification system wants access to our mail server Rather than wildly opening up the entire network, I'd like to place a firewall spanning these networks, so I can allow just the access required For example: SAN SMTP Server for email Management SAN for monitoring via SNMP Management ESX for monitoring via SNMP Target Server ESX for VMConverter Can someone recommend a free firewall that will allow this kind of thing without too much low-level tinkering of config files? I've used products such as IPcop before, and it seems to be possible to achieve this using that product if I re-purpose their ideas of "WAN", "WLAN" (the red/green/orange/blue interfaces), but was wondering if there were any other accepted products for this sort of thing. Thanks.

    Read the article

  • Troubleshooting a Windows 7 PC that wouldn't sleep

    - by NPE
    I have a new Windows 7 PC that wouldn't sleep (not just automatically, but also when specifically told to). The screen goes black momentarily, but within two seconds the machine comes back as if nothing has happened. I tried powercfg energy. This produces some errors quoted at the bottom of this post, plus some warnings about timer resolution. There are no USB devices connected other than wireless keyboard + mouse (Logitech MK250); I tried unplugging them to no effect. The motherboard is Asus P7P55D-E. powercfg lastwake says "Wake History Count - 0", which I take to mean that it never actually went to sleep. I dual boot into Ubuntu, and was having exactly the same problem on the Linux side. That turned out to do with USB 3.0, which I've now disabled in the BIOS. This has solved the problem on the Ubuntu side of things, but made no difference to Windows 7. Any suggestions? Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name Generic USB Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8087&PID_0020 Port Path 1 USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Root Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8086&PID_3B34 Port Path USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Composite Device Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_046D&PID_C52E Port Path 1,8

    Read the article

  • Home Server: cpu virtualisation, what to choose?

    - by Huygens
    I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

    Read the article

  • Can't Start SQL Server 2005 Agent - Start/Stop Are Not Enabled

    - by DaveB
    We have a brand new install of SQL Server 2005 on a Windows 2008 Server. When using the SQL Server Management Studio (2005 or 2008) from my Windows XP Professional workstation, if I right click on the SQL Server Agent, I get the context menu but the Start and Stop options are not enabled(grayed out). I am using Windows authentication, I am a member of the SysAdmin and Public SQL Server roles. Also, when right clicking on Maintenance Plans and selecting New Maintenance Plan, nothing happens. I was able to create a maintenance plan with the wizard but now am unable to execute it because SQL Server Agent isn't running? From what I was told by an admin who had access to the server, he was able to login to the box using the domain administrator account and start the SQL Server Agent service from the services applet or from the local instance of SQL Server 2005 Management Studio. Even after he started the service, it still didn't appear to be running from my workstation view through the management studio. What do I need to change to allow me to administer the agent and maintenance plans from my workstation? If I wasn't clear about anything, feel free to ask for clarification.

    Read the article

  • Configuring https access on HP A5120 Switch

    - by GerryEgan
    I am trying to configure HTTPS management on a HP a5120 switch running Version 5.20.99, Release 2215 and not having much luck. I have followed the manual by creating an SSL policy first and then enabling the HTTPS server with the SSL policy: ssl server-policy sslpol ip https ssl-server-policy sslpol ip https enable When I try and log onto the switch with Google Chrome I get the following error: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. When I look this up I have found references to errors due to TLS being used in SSL. I can find no way to specify the SSL version in the server policy. The manual has a configuration example that uses MSCEP to retrieve a certificate but in Windows 2008 R2 that feature is only available in Enterprise and Datacentre editions which I don't have. I have SSH configured and it is using a locally generated certificate so I'm not sure if I can use that but I'd like to if possible. Has anybody been able to setup HTTPS management on HP A series switches without MSCEP? Any and all help appreciated! here is a copy of my config with the interfaces removed: version 5.20.99, Release 2215 # sysname MYSYSNAME # irf domain 10 irf mac-address persistent timer irf auto-update enable undo irf link-delay # domain default enable system # telnet server enable # vlan 1 # vlan 100 description Management # radius scheme system primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 user-name-format without-domain # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher authorization-attribute level 3 service-type ssh telnet terminal service-type web # stp enable # ssl server-policy sslpol pki-domain MYDOMAIN # interface NULL0 # interface Vlan-interface199 ip address 192.168.199.140 255.255.255.0 # interface GigabitEthernet1/0/1 poe enable stp edged-port enable # interface Ten-GigabitEthernet2/1/2 # dhcp-snooping # ntp-service unicast-server 192.168.1.71 # ssh server enable # ip https ssl-server-policy sslpol ip https enable # load xml-configuration # user-interface aux 0 1 user-interface vty 0 15 authentication-mode scheme

    Read the article

  • PowerConnect 3548p SNTP and web interface not working

    - by Force Flow
    I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

    Read the article

  • Log shipping on select tables.

    - by Scott Chamberlain
    I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

    Read the article

  • Queries passed to SQL Server are getting corrupted

    - by adrianbanks
    We are experiencing a bizarre error with our application at a customer site. We have managed to narrow it down to the point where we can replicate the behaviour using just Management Studio and SQL Server. We have two machines, A and B: +------------+ +--------------------+ | [A] | | [B] | | Management | -------------- | SQL Server 2008 R2 | | Studio | | Enterprise x64 | +------------+ +--------------------+ We are running a SQL script in Management Studio on machine A against the SQL Server instance on machine B. We are not actually executing the script, just parsing it. Most of the time, the parse operation works fine. Occasionally (seemingly randomly), the parse operation fails with a syntax error. The error message shows the part of the script with the error, which appears as some SQL from the original script that has been truncated and has random characters appended to it. An example: The original SQL: SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = ST.TABLE_NAME WHERE ST.TABLE_TYPE = 'BASE TABLE' AND SC.COLUMN_NAME = 'Identity' AND ST.TABLE_NAME != 'dtproperties' ORDER BY ST.TABLE_NAME The SQL that is in error (as reported by SQL Server): SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = Sa? The above example shows how the query is being corrupted. It doesn't always happen, and is not always the same bit of SQL that causes the error. Parsing this script against another SQL Server instance produces no errors, showing that the script is fine. It appears that something is corrupting the SQL that is being received the the server. This leads me to think that the problem lies either with the client end or in the transmission of the SQL from the client to the server. I have a SQL trace from the period where an error occurs, which shows the SQL has been corrupted when SQL Server receives it. We have been unable to track down any possible cause of this behaviour, and so cannot find a fix. Because the errors occur seemingly randomly, it is also very hard to generate reproduction steps to submit a bug report. Any ideas?

    Read the article

  • Install Exchange 2013 with DSC

    - by Alain Laventure
    I tried to install Exchange 2013 with the resource windowsProcess in existing Exchange Configuration. All prerequisites are installed (the Exchange Organization still exists). This is my Resource section: WindowsProcess Exchange2013 { Credential=$credential Path= "C:\Sources\Cumulative Update 5 for Exchange Server 2013 (KB2936880)\Setup.exe" Arguments= "/mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /TargetDir:C:\EX2013" Ensure= "Present" } #End Filter } #End Node } # End configuration /* @TargetNode='TargetDSC02' @GeneratedBy=exadmin @GenerationDate=08/02/2014 08:16:03 @GenerationHost=SOURCEDSC02 */ instance of MSFT_Credential as $MSFT_Credential1ref { Password = "Password1"; UserName = "S05\\Exadmin"; }; Exadmin is a member of Orgaganization Management Group and it is also member of Domain Admin Group, to be able to install Exchange When I execute this resource , Exchange Installation Start but after 1 minute the installation stops with this error: Failed [Rule:GlobalServerInstall] [Message:You must be a member of the 'Organization Management' role group or a member of the 'Enterprise Admins' group to continue.] To be sure that the right is really the problem I create a special User with only Administrator right of the Exchange server and with no Exchange Permission I run manually on the new Exchange server .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And I got the Same error that with DSC. After I add my test user in the Organization Management Group and I run again manually .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And the Exchange 2013 installation finish without any error. That prove that the problem with DSC is Permission right.

    Read the article

  • TEMP environment variable occasionally set incorrectly

    - by Roger Lipscombe
    Occasionally, I find my TEMP and TMP environment variables set to C:\Windows\TEMP. They should be set to %USERPROFILE%\AppData\Local\Temp, and are configured correctly in System Properties. This manifests itself as error messages like the following: ---> System.InvalidOperationException: Unable to generate a temporary class (result=1). error CS2001: Source file 'C:\Windows\TEMP\gb_pz65v.0.cs' could not be found error CS2008: No inputs specified ...which occurs in various .NET applications (in particular Visual Studio 2010 or SQL Server Management Studio). Alternatively, SQL Server Management Studio will report: Value cannot be null. Parameter name: viewInfo (Microsoft.SqlServer.Management.SqlStudio.Explorer) If I run PowerShell elevated, then $env:TEMP is set correctly. If I run PowerShell non-elevated, then it's not. I believe that it should be set correctly in both cases. If not, it's the wrong way round. The same is true for CMD.EXE. Rebooting fixes it, temporarily, until something breaks it again. Presumably something loaded into Explorer.exe is messing with its environment variables, but what? The values in the registry are correct, even while this is happening: HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Environment has TEMP = %SYSTEMROOT%\Temp HKCU\Environment has TEMP = %USERPROFILE%\AppData\Local\Temp By setting a breakpoint on shell32!RegenerateUserEnvironment, I'm able to trap it when it happens, but I still don't know why explorer.exe is reading the wrong environment variables. I can reproduce it consistently by broadcasting a WM_SETTINGCHANGE message (I wrote a one-line C++ program to do this). Watching the activity in Process Monitor shows that explorer.exe doesn't even look at HKCU\Environment. What is going on?

    Read the article

  • What could be wrong with my VLAN?

    - by Matt
    I've got a VLAN 10 setup as a management VLAN. The management VLAN comes off port 48 and links to another set of switches that do not support VLAN's so it was I believe set up as an untagged access port. In the past this was a different brand of switch and this worked fine. However, since changing to the HP V1910-48G series I can't seem to get this working. I must point out that as far as I'm aware it is wired up properly (I can't check this physically as I'm working remote and have asked the tech who's got access to double check for me). Now I don't have a huge amount of experience with VLAN environments but AFAIK this is right. I've set the port 48 (linked to the management switches) as an untagged port with PVID 10 and access link type. Is this all I'd need to do from a configuration perspective to ensure all devices connected to port 48 would end up being on VLAN 10 and not needing to tag their frames. i.e. the tag would be added by the switch before being forwarded.

    Read the article

  • Un-do Windows disk convert HFS+

    - by BLAKE
    Last night, a friend asked my to give him a copy of a word document. He handed me an external hard drive and left. I plugged the hard drive into my file server running Windows Server 2003, opened disk management and clicked OK. (I know that in Windows 2003 you need to manually assign a drive letter to external drives.) I then looked at the drive in disk management and it said that it was unallocated space. I called my friend and he said that there was data on the drive, but he used it with his Mac Book. Aperantly when I clicked OK in disk management I converted the from HFS+ file system to something else. Is there any way to undo the disk convert? I immediately removed the drive, so there was no writing to it. Windows did not format the drive, it just converted it. Is the data still there? All the data recovery programs I have are for windows, can they read the Mac file system? I need to get the data back, what can I do?

    Read the article

  • Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • Good support to multiple desktops AND multiple monitors in Linux (Ubuntu)?

    - by Somebody still uses you MS-DOS
    I'm starting to have A LOT of opened windows in my machine. Sometimes within a project, I have e-mail/task management/personal e-mail/twitter, and a lot of different opened applications/terminal in my Linux environment. Nowadays I have 4 worspaces: Corporate management (e-mail) and corporate messenger; Work (Documents, Requisites) Dev (Development, All gVim windows, terminal and Firefox for development) Personal (Personal stuff: personal e-mail, delicious, twitter and so on) Sometimes it would be interesting to have different workspaces to projects instead of this configuration I have nowadays that are classes of work (bad name, I know, but I think you got the idea). I'm starting to think about using two monitors: one with Corporate Management, Work and Personal. The second monitor is only the development state: each workspace here is about a project being worked on instead of groups of works like before. A workspace may be implementing different classes for example. My question is: I just want to change to a second monitor using the mouse. I want to still be able to change workspaces in the same monitor using keyboard shortcuts. The keyboard shortcuts wouldn't change monitors, just worskpaces on the same monitor. Does Linux (Ubuntu 10.04 Lucid Lynx) support this envisioned setup? If so, how?

    Read the article

  • Allied Telesis router: IP filtering for the LOCAL interface

    - by syneticon-dj
    Given an Allied Telesis router with an AlliedWare OS (2.9.1) I would like to disable access to all management services of the router except for a number of subnets (or alternatively have what is a "management VLAN" with other manufacturers' switch and router models). What I have tried so far: creating a new VLAN and an appropriate IP interface, setting the LOCAL IP into this subnet, creating an IP filter for the IP interface and specifying my exclusion subnets: it simply does not work as intended as I can access the LOCAL IP set from any of the other VLAN interfaces - the traffic is apparently not going through my defined filter set at all creating a new IP filter set and binding it to the LOCAL IP interface: this seems not to affect any kind of traffic at all, the counters for the filter set remain at zero packets setting the Remote Security Officer Level IP address range: this only restricts the ability for a user with the Security Officer privilege level to log in from any but the specified address ranges / subnets. Unfortunately, it does not prevent service availability (and thus DoS capacity) or the ability to log in as a less privileged user (e.g. a "manager") calling technical support: unfortunately no solution so far What I have not tried: creating a filter set for each and every IP interface defined on the router and excluding access to the router's management IP: I would like to reduce the overhead induced by IP filters as the router already is CPU-constrained at times. Setting up filters for every IP interface would mean that each and every traffic packet would have to pass the filters, thus consuming CPU cycles. If by any means possible, I would like to find a different solution.

    Read the article

  • Un-do Windows disk convert HFS+

    - by BLAKE
    Last night, a friend asked my to give him a copy of a word document. He handed me an external hard drive and left. I plugged the hard drive into my file server running Windows Server 2003, opened disk management and clicked OK. (I know that in Windows 2003 you need to manually assign a drive letter to external drives.) I then looked at the drive in disk management and it said that it was unallocated space. I called my friend and he said that there was data on the drive, but he used it with his Mac Book. Aperantly when I clicked OK in disk management I converted the from HFS+ file system to something else. Is there any way to undo the disk convert? I immediately removed the drive, so there was no writing to it. Windows did not format the drive, it just converted it. Is the data still there? All the data recovery programs I have are for windows, can they read the Mac file system? I need to get the data back, what can I do?

    Read the article

  • 2008R2 Standard and Hyper-V and Ram Usage (Usable vs Available)

    - by Mark
    A new server was purchased for our development team to start utilizing the full feature set of TFS, namely Lab Management. Because of the need for Lab Management we bought a fairly beefy machine to handle this task and to also act as a build machine. I have been tasked to setup additional features TFS on this machine starting out with a build controller and eventually going towards a full out Lab Management setup using Hyper-V. My question: Upon initially logging I noticed that Windows is registering 64gb but only 32gb available. I know this is a limitation because of licencing since only Standard Edition is installed. Since Hyper-V is another layer that handles the virtualization of guest OS's is Hyper-V able to access this memory? Or is Hyper-V memory usage also limited by 2008 R2 Standard? If Hyper-V can somehow access this memory, is this how it should be setup? Or should the host 2008R2 Standard be upgraded to Enterprise so the Host can utilize the full 64gb? Before I go hog wild and using TFS I wanted to ask some experts so I don't need to reinstall the OS down the road to utilize the additional 32gb. Thanks for any help or links you can share.

    Read the article

  • How to format my external HDD back to as "removable storage"?

    - by user990106
    Recently I formated my Seagate FreeAgent GoFlex external HDD in Mac OS X using GUID partition table since I wanted to install another Mac OS X onto that external HDD. However I changed my mind after my external HDD being formatted. Now I want to format my external HDD back to NTFS so that I can use it with my Windows 7. However, after I connected my external HDD via USB it didn't show up in my "computer" so I used "Disk Management" to check what's wrong with it. In the "Disk Management" I saw that there was one partition of my external HDD called "EFI partition" and I found that I could not delete this partition in the "Disk Management". So I tried to use "diskpart" in cmd and select the external HDD and commanded "clean". Then the EFI partition was gone and I created new volumn on that external HDD. However, after the volumn being created my external HDD did show up in my "computer" but it is in the "Hard Disk Drive" not in the "Devices with Removable Storage" as it used to be. I'm wondering if I can do anything to it to make it recognized as a "Devices with Removable Storage"?

    Read the article

  • Where do all the old programmers go?

    - by Tony Lambert
    I know some people move over to management and some die... but where do the rest go and why? One reason people change to management is that in some companies the "Programmer" career path is very short - you can get to be a senior programmer within a few years. Leaving no way to get more money but to become a manager. In other companies project managers and programmers are parallel career paths so your project manager can be your junior. Tony

    Read the article

  • Android Title bar leaving space in when application is resumed

    - by user466607
    I am using a Tab Host in my Android App. I have the Titlebar hidden. When I leave the App and resume to it, I have some strange behaviour. If I resume to a tab using a list activity with listView.setAdapter, the title bar is hidden and the space it takes up is consumed by the App. However, if I resume to any tab without the listView.setAdapter, the Titlebar is hidden, but space which was used by it is left behind. This is pushes my tabs (which are positioned at the bottom of the screen) off the screen. The space is once again consumed by my app if I then change to any other tab. I have tried to invalidate most of the obvious Views in my App without and success. Below is my tab_activity xml. many thanks <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent"> <TabHost xmlns:android="http://schemas.android.com/apk/res/android" android:id="@android:id/tabhost" android:layout_width="fill_parent" android:layout_height="fill_parent"> <LinearLayout android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent"> <FrameLayout android:id="@android:id/tabcontent" android:layout_width="fill_parent" android:layout_height="0dip" android:layout_weight="1" /> <TabWidget android:id="@android:id/tabs" android:layout_width="fill_parent" android:layout_height="wrap_content" android:layout_weight="0" /> </LinearLayout> </TabHost> </LinearLayout> Here is the Manifest <?xml version="1.0" encoding="utf-8"?> <manifest xmlns:android="http://schemas.android.com/apk/res/android" package="com.tar.projectx" android:versionCode="1" android:versionName="1.0"> <uses-sdk android:minSdkVersion="8" /> <uses-permission android:name="android.permission.INTERNET" /> <uses-permission android:name="android.permission.ACCESS_COARSE_LOCATION" /> <uses-permission android:name="android.permission.ACCESS_FINE_LOCATION" /> <uses-permission android:name="android.permission.WRITE_EXTERNAL_STORAGE"/> <uses-permission android:name="android.permission.CALL_PHONE" /> <uses-permission android:name="android.permission.READ_PHONE_STATE" /> <uses-permission android:name="android.permission.GET_ACCOUNTS" /> <uses-permission android:name="android.permission.READ_CONTACTS" /> <uses-permission android:name="android.permission.WRITE_CONTACTS" /> <application android:theme="@android:style/Theme.Light.NoTitleBar.Fullscreen" android:icon="@drawable/icon" android:label="@string/app_name" android:debuggable="true"> <activity android:name=".Splash" android:theme="@android:style/Theme.Light.NoTitleBar.Fullscreen" android:label="@string/app_name" android:screenOrientation="portrait"> <intent-filter> <action android:name="android.intent.action.MAIN" /> <category android:name="android.intent.category.LAUNCHER" /> </intent-filter> </activity> <activity android:name="SearchActivity" android:label="SearchActivity" android:screenOrientation="portrait"></activity> <activity android:name="SearchListActivity" android:label="SearchListActivity" android:screenOrientation="portrait"></activity> <activity android:name="ContactActivity" android:label="ContactActivity" android:screenOrientation="portrait"></activity> </application> </manifest> Interestingly, if I use the code below in the onResume method of my mainActivity which holds the tabhost, once the toast disappears, the view is refreshed and the space at the top is taken up by my app again. Obviously, this isn't much of a fix, but may help someone understand what is happening. @Override protected void onResume() { super.onResume(); Toast.makeText(this, "Welcome Back", Toast.LENGTH_LONG).show(); }

    Read the article

  • VLC without border/window decoration in Windows

    - by timberwo7ves
    I'm trying to run VLC (2.1, 64 bit) without any chrome on Windows 7. You can achieve it by going to Preferences, and in the Interface tab, unchecking Integrate video in interface, and also in the Video tab, unchecking Window decorations. The problem lies in the fact that without Window decorations there is no apparent way to move or resize the video window - in GOM player, for example, you can move window by dragging on the video itself; is there an option for this in VLC? Ideally, I would like to move the window by the method described above (by dragging the video), and would like the Window decorations to reappear on mouseover, to allow resizing; I'm a new VLC user, but unsure how far the customisation goes. - I'd settle with just the moving of the window via dragging the video if this is possible by advanced setting. There is a similar question here, but not exactly, and no solution to that particular question.

    Read the article

  • Fiddler not working in Windows 7 - LAN Settings locked?

    - by Glen Little
    I've been using Fiddler for years, but now, on Windows 7 (64 bit) I cannot get it to monitor traffic from IE 8. With the Firefox add-on, it is able to monitor Firefox traffic with no problem. This is not related to monitoring HTTPS traffic, or traffic to localhost. I've tried running IE and/or Fiddler with "Run as Administrator", but no luck. The best clue to the problem that I have is that in IE8, the "Local Area Network (LAN) Settings" dialog accessed from "LAN Settings" in the Internet Options / Connections tab is all grayed out. I have two Windows 7, 64 bit computers, both on the same LAN. One works fine, the other has these settings grayed out, and a note on the Connections tab: "Some settings are managed by your system administrator". However, the system administrator has NOT set any. Any ideas?

    Read the article

  • BSOD Before Windows Will Loads - Graphics Related

    - by Brian
    Alright deep breath here: (Windows 7 Home Premium 64 bit btw) Today I installed Star Craft 2 Beta. After trying to log in, it had some issues where it said my device stopped working (referring to my video device I have to imagine). After I force quit the game there were some random "hot" (various colors if i remember correctly) pixels on the screen. I decided to reboot and try again with similar results. I figured that maybe my display drivers could stand to be updated (I don't frequently update them as I don't often run into problems). I went out to nVidia's website and grabbed the latest drivers for Windows 7 64 bit GeForce 9 series. (I have SLi-ed 9800 GTs). Everything seemed to install fine and I performed the restart. This is when things went from bad (can't play SC2 beta ;) ) to worse (can't boot into windows!). Initially the very first splash screen - I think it's the bios splash screen - had lines of colored pixels covering it. It then displayed a screen that had lots of "(" on it. After that it showed the normal windows 7 splash screen as if it were going to load into Windows. Before getting much further, it BSODed on me. It was a 0x0000003B stop error. At nvlddmkm.sys. A little digging let verified that this was a problem with an nVidia graphics device, not a real shocker. Windows decided it would try to help me diagnose the problem, which it's only answer to was a System Restore, which did nothing to alleviate the problem. I was able to boot up fine in safe mode and was not able to roll back the driver, however I did uninstall the driver and reboot. I still had the graphical anomalies during the first two screens (same colored "."'s and weird "("'s), but there was NOT a stop error. Windows loaded up, found a default driver for the device and installed it and I restarted to let it load - and had yet another BSOD Stop error. Repeat driver uninstall, this time I reloaded the same version (I think it's possible that I was running a 32 bit version or a vista versus windows 7 version, but I don't have that information handy) of the nVidia driver from their website. Restart, same anomalies, same Stop Error. I am at a loss - At this point all I can think is that the firmware for the Video cards got fried or there's actual damage to the cards which I sincerely hope is not the case but the sooner I know the better. Any insight into what I might be able to do to troubleshoot/fix this problem would be most helpful. Attached below is a dump from DxDiag. Please let me know if there is more info that I could provide. ------------------ System Information ------------------ Time of this report: 3/18/2010, 23:22:48 Machine name: BRIAN-PC Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600) (7600.win7_rtm.090713-1255) Language: English (Regional Setting: English) System Manufacturer: Dell Inc System Model: XPS 630i BIOS: Phoenix - AwardBIOS v6.00PG Processor: Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz (4 CPUs), ~2.3GHz Memory: 8192MB RAM Available OS Memory: 8190MB RAM Page File: 1855MB used, 14521MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found User DPI Setting: Using System DPI System DPI Setting: 96 DPI (100 percent) DWM DPI Scaling: Disabled DxDiag Version: 6.01.7600.16385 32bit Unicode DxDiag Previously: Crashed in DirectShow (stage 1). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information ------------ DxDiag Notes ------------ Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. -------------------- DirectX Debug Levels -------------------- Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) --------------- Display Devices --------------- Card name: Manufacturer: Chip type: DAC type: Device Key: Enum\ Display Memory: n/a Dedicated Memory: n/a Shared Memory: n/a Current Mode: 1600 x 1200 (32 bit) (1Hz) Driver Name: Driver File Version: () Driver Version: DDI Version: unknown Driver Model: unknown Driver Attributes: Final Retail Driver Date/Size: , 0 bytes WHQL Logo'd: n/a WHQL Date Stamp: n/a Device Identifier: {D7B70EE0-4340-11CF-B123-B03DAEC2CB35} Vendor ID: 0x0000 Device ID: 0x0000 SubSys ID: 0x00000000 Revision ID: 0x0000 Driver Strong Name: Unknown Rank Of Driver: Unknown Video Accel: Deinterlace Caps: n/a D3D9 Overlay: n/a DXVA-HD: n/a DDraw Status: Not Available D3D Status: Not Available AGP Status: Not Available ------------- Sound Devices ------------- Description: Speakers (Realtek High Definition Audio) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek Digital Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek HDMI Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No --------------------- Sound Capture Devices --------------------- Description: Microphone (Realtek High Definition Audio) Default Sound Capture: Yes Default Voice Capture: Yes Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 Description: Realtek Digital Input (Realtek High Definition Audio) Default Sound Capture: No Default Voice Capture: No Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 ------------------- DirectInput Devices ------------------- Device Name: Mouse Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: Keyboard Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: ESA FW Update Attached: 1 Controller ID: 0x0 Vendor/Product ID: 0x0955, 0x000A FF Driver: n/a Poll w/ Interrupt: No ----------- USB Devices ----------- + USB Root Hub | Vendor/Product ID: 0x10DE, 0x026D | Matching Device ID: usb\root_hub | Service: usbhub | +-+ USB Input Device | | Vendor/Product ID: 0x0955, 0x000A | | Location: Port_#0002.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant device | | | Vendor/Product ID: 0x0955, 0x000A | | | Matching Device ID: hid_device | | +-+ USB Input Device | | Vendor/Product ID: 0x046D, 0xC01E | | Location: Port_#0003.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant mouse | | | Vendor/Product ID: 0x046D, 0xC01E | | | Matching Device ID: hid_device_system_mouse | | | Service: mouhid ---------------- Gameport Devices ---------------- ------------ PS/2 Devices ------------ + Standard PS/2 Keyboard | Matching Device ID: *pnp0303 | Service: i8042prt | + Terminal Server Keyboard Driver | Matching Device ID: root\rdp_kbd | Upper Filters: kbdclass | Service: TermDD | + Terminal Server Mouse Driver | Matching Device ID: root\rdp_mou | Upper Filters: mouclass | Service: TermDD ------------------------ Disk & DVD/CD-ROM Drives ------------------------ Drive: C: Free Space: 324.3 GB Total Space: 608.4 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: D: Free Space: 1.0 GB Total Space: 2.0 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: E: Model: TSSTcorp DVD+-RW TS-H653F SCSI CdRom Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7600.16385 (English), , 0 bytes -------------- System Devices -------------- Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B7&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&18 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AF&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0A Driver: n/a Name: PCI standard host CPU bridge Device ID: PCI\VEN_10DE&DEV_03A3&SUBSYS_02491028&REV_A2\3&2411E6FE&1&00 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0267&SUBSYS_02491028&REV_A1\3&2411E6FE&1&78 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B6&SUBSYS_02491028&REV_A1\3&2411E6FE&1&10 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AE&SUBSYS_02491028&REV_A1\3&2411E6FE&1&09 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0272&SUBSYS_02491028&REV_A3\3&2411E6FE&1&52 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0266&SUBSYS_02491028&REV_A1\3&2411E6FE&1&70 Driver: n/a Name: LSI 1394 OHCI Compliant Host Controller Device ID: PCI\VEN_11C1&DEV_5811&SUBSYS_02491028&REV_70\4&14591D7E&0&2880 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B5&SUBSYS_02491028&REV_A1\3&2411E6FE&1&06 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AD&SUBSYS_02491028&REV_A1\3&2411E6FE&1&08 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0270&SUBSYS_02491028&REV_A2\3&2411E6FE&1&48 Driver: n/a Name: Standard Dual Channel PCI IDE Controller Device ID: PCI\VEN_10DE&DEV_0265&SUBSYS_02491028&REV_A1\3&2411E6FE&1&68 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&4BABE2A&0&0028 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B4&SUBSYS_02491028&REV_A1\3&2411E6FE&1&07 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&01 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_026F&SUBSYS_CB8410DE&REV_A2\3&2411E6FE&1&80 Driver: n/a Name: NVIDIA nForce PCI System Management Device ID: PCI\VEN_10DE&DEV_0264&SUBSYS_02491028&REV_A3\3&2411E6FE&1&51 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&10BD3C89&0&0018 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B3&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0E Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AB&SUBSYS_02491028&REV_A1\3&2411E6FE&1&04 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_10DE&DEV_026E&SUBSYS_02491028&REV_A3\3&2411E6FE&1&59 Driver: n/a Name: PCI standard ISA bridge Device ID: PCI\VEN_10DE&DEV_0260&SUBSYS_02491028&REV_A3\3&2411E6FE&1&50 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&11 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B2&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0D Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&02 Driver: n/a Name: Standard OpenHCD USB Host Controller Device ID: PCI\VEN_10DE&DEV_026D&SUBSYS_02491028&REV_A3\3&2411E6FE&1&58 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&12 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B1&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0C Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A9&SUBSYS_02491028&REV_A1\3&2411E6FE&1&03 Driver: n/a Name: High Definition Audio Controller Device ID: PCI\VEN_10DE&DEV_026C&SUBSYS_02491028&REV_A2\3&2411E6FE&1&81 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B8&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&28 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B0&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0B Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A8&SUBSYS_02491028&REV_A2\3&2411E6FE&1&05 Driver: n/a Name: NVIDIA nForce Networking Controller Device ID: PCI\VEN_10DE&DEV_0269&SUBSYS_02491028&REV_A3\3&2411E6FE&1&A0 Driver: n/a --------------- EVR Power Information --------------- Current Setting: {5C67A112-A4C9-483F-B4A7-1D473BECAFDC} (Quality) Quality Flags: 2576 Enabled: Force throttling Allow half deinterlace Allow scaling Decode Power Usage: 100 Balanced Flags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 50 PowerFlags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 0

    Read the article

  • How to force high-dpi scaling?

    - by Ian Boyd
    How can i force an application to be high-dpi scaled? Or alternatively, how can an application that is not manifested as high-dpi aware, and doesn't have dpi-scaling disabled from the Properties-Compatibility tab, not be scaled? Pretend i have an application, who's developers decided to manifest it as high-dpi aware, when it really isn't. How can i force dpi-scaling? Pretend i have an applicaiton that Microsoft has applied the "HighDpiAware" compatiblity shim to, when the application really isn't. How can i force dpi-scaling? Pretend i have an application (i.e. Shareaza) that does not have a dpi-aware manifest, does not disable dpi-scaling from the application's Properties tab, but high-dpi scaling is not being applied? How can i force it? How can i force Windows to apply dpi-scaling to an application? See also

    Read the article

< Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >