Search Results

Search found 8167 results on 327 pages for 'general tapioca'.

Page 286/327 | < Previous Page | 282 283 284 285 286 287 288 289 290 291 292 293  | Next Page >

• How to set up a file server in a restricted corporate environment

  - by Emilio M Bumachar

  I work in a big corporation, and the disk space my team gets in the corporate file server is so low, I am considering turning my work PC into a file server. I ask this community for links to tutorials, software suggestions, and advice in general about how to set it up. My machine is an Intel Core2Duo E7500 @ 3GHz, 3 GB of RAM, Running Windows XP Service Pack 3. Upgrading, formatting or installing another OS is out of the question. But I do have Administrator priviledges on the PC, and I can install programs (at least for now). A lot of security software I don't even know about is and must remain installed. But I only need communication whithin the corporate network, which is not restricted. People have usernames (logins) on the corporate network, and I need to use them to restrict access. Simply put, I have a list of logins of team members, and only people in the list should access the files. I have about 150 GB of free disk space. I'm thinking of allocating 100 GB to the team's shared files. I plan monthly backups on machines of co-workers, same configuration. But automation of backups is a nice, unnecessary feature: it's totally acceptable for me to manually copy the contents to a different machine once a month. Uptime is important, as everyone would use these files in their daily work. I have experience as a python and C programmer, but no experience whatsoever as a sysadmin, and almost nothing of my programming experience is network programming. I'm a complete beginner in this. Thanks in advance for any help. EDIT I honestly appreciate all the warnings, I really do, but what I plan to make available is mostly stuff that now is solely on DVDs just for space reasons. It's 'daily work' to read them, but 'daily work write' files will remain on the corporate server. As for the importance of uptime, I think I overstated it: a few outages are OK, it's already an improvement over getting the DVDs. As for policy, my manager is kind of on my side, I will confirm that before making my move. As for getting more space through the proper channels, well, that was Plan A, and it's still on the table... But I don't have much hope. I'm not as "core businees" as I'd like.

  Read the article

• Keep source IP after NAT

  - by John Miller

  Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

  Read the article

• Automating silent software deployments on Solaris 10

  - by datSilencer

  Hello everyone. Essentially, the question I'd like to ask is related to the automation of software package deployments on Solaris 10. Specifically, I have a set of software components in tar files that run as daemon processes after being extracted and configured in the host environment. Pretty much like any server side software package out there, I need to ensure that a list of prerequisites are met before extracting and running the software. For example: Checking that certain users exists, and they are associated with one or many user groups. If not, then create them and their group associations. Checking that target application folders exist and if not, then create them with preconfigured path values defined when the package was assembled. Checking that such folders have the appropriate access control level and ownership for a certain user. If not, then set them. Checking that a set of environment variables are defined in /etc/profile, pointed to predefined path locations, added to the general $PATH environment variable, and finally exported into the user's environment. Other files include /etc/services and /etc/system. Obviously, doing this for many boxes (the goal in question) by hand can be slow and error prone. I believe a better alternative is to somehow automate this process. So far I have thought about the following options, and discarded them for one reason or another. 1) Traditional shell scripts. I've only troubleshooted these before, and I don't really have much experience with them. These would be my last resort. 2) Python scripts using the pexpect library for analyzing system command output. This was my initial choice since the target Solaris environments have it installed. However, I want to make sure that I'm not reinveting the wheel again :P. 3) Ant or Gradle scripts. They may be an option since the boxes also have java 1.5 enabled, and the fileset abstractions can be very useful. However, they may fall short when dealing with user and folder permissions checking/setting. It seems obvious to me that I'm not the first person in this situation, but I don't seem to find a utility framework geared towards this purpose. Please let me know if there's a better way to accomplish this. I thank you for your time and help.

  Read the article

• Recognizing Dell EquilLogic with Nagios

  - by user3677595

  EDIT: All firmware and models are compatible, that is why nothing is posted about it. Okay, so there will be a lot here, so please bare with me. I've been working on this now for a few hours (reading manuals and such) so I'm not just coming here right out of the blue. I am working on a PRE-EXISTING Nagios server where there are several other existing plugins and checks running and working. Now I want to add another server there to check so I made the following modifications: First and foremost, I added a file to /usr/local/nagios/libexec named: check_equallogic.sh. The permissions are 755, the same as all others. I have chowned to nagios:nagios and in the listing it shows the Owner as Nagios. I then added a command to the commands.cfg file in \usr\local\nagios\etc\objects that shows the following: # 'check_equallogic' command definition define command{ command_name check_equallogic command_line $USER1$/check_equallogic -H $HOSTADDRESS$ -C $ARG1$ -t $ARG2$ $ARG3$ } Following this, I created a file named equallogic.cfg in the objects directory and it contains (more or less): define host{ use linux-server ; Inherit default values from a template host_name 172.16.50.11 ; The name we're giving to this device alias EqualLogic ; A longer name associated with the device address 172.16.50.11 ; IP address of the device contact_groups admins } Check Equallogic Information define service{ use generic-service host_name 172.16.50.11 service_description General Information check_command check_equallogic!public!info } After ensuring that permissions are okay for all files, I restart the nagios service, no errors. When I go into the WebGUI, I get the following errors AFTER the check runs: (Return code of 127 is out of bounds - plugin may be missing) Extra, probably unrelated problem Furthermore, when I log into the EquilLogic server, under Audit logs I get the following error: Level: AUDIT Time: 26/05/2014 3:59:13 PM Member: ps4100-1 Subsystem: agent Event ID: 22.7.1 SNMP packet validation failed, request received from 172.16.10.11 An snmpwalk receives a timeout, whereas others succeed. I will work on importing the MIBs tomorrow. The reason why I am mentioning it is because I want to make sure that it is only a MIB issue for the SNMP. If it is, then ignore this area. I am entirely unsure of what to do here.

  Read the article

• Tool or script to detect moved or renamed files on Linux prior to a backup

  - by Pharaun

  Basically I am searching to see if there exists a tool or script that can detect moved or renamed files so that I can get a list of renamed/moved files and apply the same operation on the other end of the network to conserve on bandwidth. Basically disk storage is cheap but bandwidth isn't, and the problem is that the files often will be reorganized or moved around into a better directory structure thus when you use rsync to do the backup, rsync won't notice that its a renamed or moved file and re-transmission it over the network all over again despite having the same file on the other end. So I am wondering if there exists a script or tool that can record where all the files are and their names, then just prior to a backup, it would rescan and detect moved or renamed files, then I can take that list and re-apply the move/rename operation on the other side. Here's a list of the "general" features of the files: Large unchanging files They can be renamed or moved around [Edit:] These all are good answers, and what I end up doing in the end was looking at all of the answers and will be writing some code to deal with this. Basically what I am thinking/working on now is: Using something like AIDE for the "initial" scan and enable me to keep checksums on the files because they are supposed to never change, so it would aid on detecting corruption. Creating an inotify daemon that would monitor these files/directory and recording any changes relating to renames & moving the files around to a log file. There are some edge cases where inotify might fail to record that something happened to the file system, thus there is a final step of using find to search the file system for files that has a change time latter than the last backup. This has several benefits: Checksums/etc from AIDE to be able to check/make sure that some media did not get corrupt Inotify keeps resource usage low and no need to re-scan the filesystem over and over No need to patch rsync; If I have to patch things I can, but I would prefer to avoid patching things to keep the burden lower, (IE don't need to re-patch everytime there is an update). I've used Unison before and its really nice, however I could've sworn that Unison does keep copies around on the filesystem and that its "archive" files can grow to be rather large?

  Read the article

• Postfix issues sending mail to addresses under domain located on server

  - by iamthewit

  I recently installed virtualmin on my nice shiny new rackspace cloud. Everything went seemlessly but I've been having some issues getting emails to send properly. The problem seems to be that the server can not send mail to email addresses where the domain is owned by my server. For example, on my server I run multiple virtual domains, lets call this one test.com. When I run the mail command from shell (mail [email protected]) I get the following back from my maillog: Oct 6 14:55:18 test postfix/pickup[8737]: DC1131612CC: uid=0 from= Oct 6 14:55:18 test postfix/cleanup[8769]: DC1131612CC: [email protected] Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: [email protected], size=353, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/error[8771]: DC1131612CC: [email protected], relay=none, delay=0, delays=0/0/0/0, dsn=5.0.0, status=bounced (User unknown in virtual alias table) Oct 6 14:55:18 test postfix/cleanup[8769]: DD07D1612D1: [email protected] Oct 6 14:55:18 test postfix/bounce[8772]: DC1131612CC: sender non-delivery notification: DD07D1612D1 Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: from=<, size=2268, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: removed Oct 6 14:55:18 test postfix/local[8773]: DD07D1612D1: [email protected], relay=local, delay=0.03, delays=0/0/0/0.03, dsn=2.0.0, status=sent (delivered to command: /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME) Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: removed when I run mail [email protected] the message is sent and received perfectly fine. I'm a bit of a noob when it comes to servers, but I pick things up fairly quickly, so please excuse any incorrect terminology and my general noobiness. Any help would be greatly appreciated, I've been googling for quite a while but I haven't found a solution yet, I'll add a copy of my main.cf file in a response below cheers guys here is the reformatted postconf, do you want the reformatted main.cf file too, or is this enough? alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 home_mailbox = Maildir/ html_directory = no mailbox_command = /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man myhostname = server.test.com newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sender_bcc_maps = hash:/etc/postfix/bcc sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• Diff 2 files while ignoring parts of lines

  - by Millianz

  I would like to diff a file system. Currently my bash script prints out the file system recursively into a file (ls -l -R) and diffs it with an expected output. An example for a line in this file would be: drw---- 100000f3 00000400 0 ./foo/ My current diff command is diff "$TEMP_LOG" "$DIFF_FILE_OUT" --strip-trailing-cr --changed-group-format='%' --unchanged-group-format='' "$SubLog" As you can see I ignore additional lines in the current output file, I only care about lines that match with the master output. I now have the problem though that some files may differ in size, or a folder might even have a different name, but due to it's location I know what access rights it should have. For example: Output: ------- 00000000 00000000 528 ./foo/bar.txt Master: ------- 00000000 00000000 200 ./foo/bar.txt Only the size differs here, and it doesn't matter, I would like to just ignore certain parts of the diff, kind of like an ansi c comment. Master: ------- 00000000 00000000 /*200*/ ./foo/bar.txt -- OR -- Master: d------ 00000000 00000000 /*10*/ ./foo//*123123*///*76456546*//bar.txt Output: d------ 00000000 00000000 0 ./foo/asd/sdf/bar.txt And still have it diff correctly. Is this even possible with diff, or will I have to write a custom script for it? Since I'm fairly new to cygwin I might be using the completely wrong tool all together, I'm happy for any suggestions. Update: Taking a step back, here is the general task at hand that I want to achieve. I want to write a script that checks the file system to see if the read/write permissions are set up correctly. The structure of the file system is under my control, so I don't have to worry about it changing too much. Sometimes folders/files might not be present, but if they are their permissions must be checked. For Example assume that the following is a snapshot of the current file system structure drw ./foo drw ./foo/bar -rw ./foow/bar/bar.txt drw ./foo/baz -rw ./foo/baz/baz.txt And this is what the file system structure might dictate, i.e. if these folders / files are present, the permissions must match. drw ./foo drw ./foo/bar -rw ./foo/bar/bar.txt --- ./foo/bar/foobar.txt drw ./foo/baz -rw ./foo/baz/foobaz.txt In this case the file system checked out ok, since all files present match their expected values. The situation becomes more complicated as soon as certain folders might have any arbitrary name, only due to their location I know what their permissions should be. Assume that the directory ./foo/bar in the above example might be such a case, i.e. instead of bar the folder could have any name, but still match the -rw permissions. This seems like a very complicated situation, and I'm not even sure if I can solve it with bash scripting alone. I might have to write an actual application.

  Read the article

• Can you set up a gaming LAN using OpenVPN installed in a VMware guest OS and be playing the game on the host OS?

  - by Coder

  I would like to setup a gaming VPN. Ie. I have some games that work over LAN and would like to play them with people that are not on my LAN. I know I can do this with OpenVPN. My ultimate goal would be to run OpenVPN portably on my host OS and not even need any virtualization. As such i don't want to install it on my host, but i'm fine with running it portably. I'm even fine with temporarily adding registry keys, and then running a .reg file to remove these entries once i'm done. To this effect i have installed OpenVPN on a virtual machine and diffed the registry. I then manually (using a .reg file) added all the keys that seem important on my host OS and copied the installation folder of OpenVPN onto my host machine. Then i try to run openVPN GUI 1.0.3 as a test and it says "Error opening registy for reading (HKLM\SOFTWARE\OpenVPN). OpenVPN is probably not installed". I verified that that key is indeed in the registry with all subkeys and it looks correct. I have tried running the GUI as an administrator and in compatibility mode with no success. I am running Windows 7. If this fails then i would be happy with installing OpenVPN on a virtual machine in VMWare but they key is that i will be running the game installed on my host machine. The first question for this option is if this is even possible. The second is, that I can't get the VM to have internet access if I use bridging but i can if i use NAT. Is it possible to do this game VPN setup with VMWare guest OS running using NAT? Summary of questions: -Is it possible to run openVPN portably and if so what did i miss above? -If it's not possible to run it portably, then can setup a gaming LAN by installing OpenVPN in a guest OS with NAT and how can i do this? -If the above is not possible then can i install OpenVPN in a guest using bridging and if so how can i set this up with a Windows 7 host and Windows XP guest as currently i can't get the guest to be able to access the internet in bridging mode, but it working in NAT mode. -In general is there any good documentation on setting up a gaming LAN with OpenVPN (i am using 2.1.4) as i have never set up a VPN of any sort before so any help would be much appreciated. Thanks!

  Read the article

• Google analytics and multiple independent subdomains

  - by MTilsted

  I need some help trying to setup google analytics correct. Here is my setup: We host sites for multiple customers, and each customer have their own subdomain on our site. So we have customerA.oursite.com and customerB.oursite.com As we add more customers we get more subdomains. We do want to track all data for each customer independent, but I don't want to to create a new google tracking code for each new customer. So my plan is to track all visits with "oursite.com", and then I will create a filter in google Analytics to get data for each specific customer(All visits for a specific subdomain). Is this(One tracking code, and a subdomain filter) the right way to do it? To create a subdomain filter i add a new profile for each customer, and then add a custom filter saying include "Request URI" and fill in "CustomerDomain.oursite.com". Is this the correct way to do it? And a general question about filters: Is it really impossible to create a new filter by applying it to data in an existing profile? I would really like to just collect all the data in one "main" profile and then create subdomain filters as we need them. But it seems that google only apply filters to new incomming data, not existing data. Is this really true? The following is my tracking code. Is '_setDomainName','none' the right thing to do? <script type="text/javascript"> /* Tracking code for qrtown.com */ var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-11584298-10']); _gaq.push(['_setDomainName', 'none']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script>

  Read the article

• Linux Best Practices

  - by Zac

  I'm a life-long Windows developer switching over to Linux for the first time, and I'm starting off with Ubuntu to ease the learning curve. My new laptop will primarily be a development machine: 6GB RAM, 320 GB HD. I'd like there to be 2 non-root users: (a) Development, which will always be me, and (b) Guest, for anyone else. I assume the root user is added by default, like System Administrator in Windows. (1) I'd like to mount /home to its own partition, but how does this work if I have two user accounts (Development and Guest)? Are there 2 separate /home directories, or do they get shared? Is it possible to allocate more space for Development and only a tiny bit of space for Guest in GRUB2? How?!?! (2) I'm assuming that its okay that all of my development tools (Eclipse & plugins, SVN, JUnit, ant, etc.) and Java will end up getting installed in non-/home directories such as /usr and /opt, but that my Eclipse/SVN workspace will live under my /home directory on a separate partition... any problems, issues, concerns with that? (3) As far as partitioning schemes, nothing too complicated, but not plain Jane either: Boot Partition, 512 MB, in case I want to install other OSes Ubuntu & non-/home file system, 187.5 GB Swap Partition, 12 GB = RAM x 2 /home Partition, 120 GB I don't have any bulky media data (I don't have music or video libraries, this is a lean and mean dev machine) so having 320 GB is like winning the lottery and not knowing what to do with all this space. I figured I'd give a little extra space to the OS/FS partition since I'll be running JEE containers locally and doing a lot of file IO, logging and other memory-instensive operations. Any issues, problems, concerns, suggestions? (4) I was thinking about using ext4; seems to have good filestamping without any space ceiling for me to hit. Any other suggestions for a dev machine? (5) I read somewhere that you need to be careful when you install software as the root user, but I can't remember why. What general caveats do I need to be aware of when doing things (installing packages, making system configurations, etc.) as root vs "Development" user? Thanks!

  Read the article

• Managing hosts and iptables in scalable architecture

  - by hakunin

  Let's say I have a load balancer in front of 3 app servers. Let's say I also have these services available at certain IPs: Postgres server Redis server ElasticSearch server Memcached server 1 Memcached server 2 Memcached server 3 So that's 6 nodes at 6 different IP addresses. Naturally, every one of my 3 app servers needs to talk to these 6 servers above. Then, to make it a bit funkier, I also have 3 worker servers. And each worker also talks to the above 6 servers, but thankfully workers and apps never need to talk to each other. Now's the kicker. Everything is on Digital Ocean VPS. What that means is: you have no private network, no private IPs. You only have separate, random IP address on each machine. You can't mask them or anything. So in order to build a secure environment I would have to configure some iptables. For example: Open app servers be accessed by load balancer server Open redis, ES, PG, and each memcached servers to be accessed by each app's IP and each worker's IP This means that every time I add an app or worker I have to also reconfigure iptables in those above 6 servers to welcome the new app or worker. Is there a way to simplify this type of setup? I was thinking — what if there was a gateway machine between apps/workers and the above 6 machines. This way all the interaction would always happen via the gateway server, and when I add a new app or worker I wouldn't need to teach the 6 servers to let it in. If I went this route, then I'd hope a small 512mb server could handle that perhaps, and there wouldn't be almost any overhead. Or would there? Please help with best way to handle this situation. I would appreciate an answer as concrete as possible. I don't think this is too specific, because this general architecture is very common, and Digital Ocean is becoming increasingly popular. A concrete solution here would be much appreciated by many.

  Read the article

• SMBfs mounting OK, listing OK, Read KO, smbclient OK

  - by Kwaio

  I've tried to make the title the most meaningfull I could but it still looks ugly. The premises. We are using RHEL3-U8 as OS on most servers here, don't ask me why or suggest to upgrade, it's not on today's schedule. That means kernel used is 2.4.21 I have no access to the remote server, but I know it is a netApp NAS rack. $> smbclient --version Version 3.0.9-1.3E.9 Here is the /etc/fstab line : //NASHOSTNAME/share /mnt/mydir smbfs ro,uid=123,gid=123,workgroup=XXXX,credentials=/somefile 0 0 Here is the following mount output line //NASHOSTNAME/share on /mnt/mydir type smbfs (0) The symptoms. I can list the share without problems, even cd in there. The issue appears if I try to read any file : $> cat /mnt/mydir/fileX.txt cat: /mnt/mydir/fileX.txt: Input/output error In the system logs (/var/log/kernel for example) the following errors appear. Jul 30 15:40:02 hostname kernel: smb_errno: class ERRHRD, code 31 from command 0x2 Jul 30 15:40:02 hostname kernel: smb_errno: class ERRHRD, code 31 from command 0x2 Jul 30 15:40:02 hostname kernel: smb_open: fileX.txt open failed, result=-5 Jul 30 15:40:02 hostname kernel: smb_errno: class ERRHRD, code 31 from command 0x2 Jul 30 15:40:02 hostname kernel: smb_errno: class ERRHRD, code 31 from command 0x2 Jul 30 15:40:02 hostname kernel: smb_open: fileX.txt open failed, result=-5 Jul 30 15:40:02 hostname kernel: smb_readpage_sync: fileX.txt open failed, error=-5 The ERRHRD code 0x001F error is "General hardware failure" although it seems samba sometimes uses it for a different purpose, see http://www.ubiqx.org/cifs/SMB.html [Strange behaviour Alert] Additionnal informations : There is another SMB mountpoint on the system pointing to a (linux) host using samba and this one works. What I have tried. I have tried adding debug=4 to the mounting options and remounting the share and the logs still look the same. I have tried to mount the share with smbclient and I am able to fetch files with the get command. Both targets are in the same subnet, so network problem should be out, even if the LAN goes through a VPN with optimizers, MTU has already been decreased to 1450. I can also mount the share through NFS but then the files are all root.root 700 and I need to read them with another user...

  Read the article

• Why would a process monitoring script use exit 1; on finding no problems?

  - by user568458

  General question: On a Linux (Centos) server, if a process monitoring script run by cron is set to close with exit 1; rather than exit 0; on finding that everything is okay and that no action is needed, is that a mistake? Or are there legitimate reasons for calling exit 1; instead of exit 0; on the "Everything's fine, no action needed" condition? exit 0; on finding no problems seems to me to be more appropriate. But maybe there's something I'm not aware of. For example, maybe there's something specific to Cron? Or maybe there's a convention in process monitoring scripts that 'failure' means 'this script failed to need to fix a problem' (rather than what I would expect which is that exit 1; would mean 'the process being monitored has failed'?) My specific case: I'm looking at a process monitoring script written by my web hosting company. By process monitoring script, I mean a script executed by Cron on a regular basis that checks if an important system process is running, and if it isn't running, takes actions such as mailing an administrator or restarting the process. Here's the (generalised) structure of their script, for a service running on port 8080 (in this case, Apache Tomcat): SERVICE=$(/usr/sbin/lsof -i tcp:8080 | wc -l); if [ $SERVICE != 0 ]; then exit 1; else #take action fi Seems simple enough even for someone with limited knowledge like me, except the exit 1; part seems odd. As I understand it, exit 0; closes a program and signifies to the parent that executed the program that everything is fine, exit n; where n0 and n<127 signifies that there has been some kind of error or problem. Here, their script seems to go against that rule - it calls exit 1; in the condition where everything is fine, and doesn't exit after taking remedial action in the problem condition. To me, this looks like a mistake - but my experience in this area is limited. Are there cases where calling exit 1; in the "Everything's fine, no action needed" condition is more appropriate than calling exit 0;? Or is it a mistake? Wider context is pretty simple. It's a Centos VPS, running Plesk. The script is being called by Cron via Plesk's "Scheduled tasks" Cron manager. There's no custom layer between Cron and this script that would respond in an unusual way to the exit call. It's a fairly average, almost out-of-the box Plesk-managed Centos VPS (in so far as there is such a thing). The process being monitored by this script is Apache Tomcat.

  Read the article

• Reviews Cheyney Group Marketing: What accounting softwares are available in the market for small businesses?

  - by user225556

  Accounting is the language of business, and good accounting software can save you hundreds of hours at the business equivalent of Berlitz. There's no substitute for an accounting pro who knows the ins and outs of tax law, but today's desktop packages can help you with everything from routine bookkeeping to payroll, taxes, and planning. Each package also produces files that you can hand off to an accountant as needed. Small-business managers have more accounting software options than ever, including subscription Web-based options that don't require their users to install or update software. Many businesses, however--including those that need to track large inventories or client databases, and those that prefer not to entrust their data to the cloud--may be happier with a desktop tool. We looked at three general-purpose, small-business accounting packages: Acclivity AccountEdgePro 2012 (both the product and the company were previously called MYOB), Intuit QuickBooks Premier 2012, and Sage's Sage 50 Complete 2013 (the successor to Peachtree Complete). All three packages offer a solid array of tools for tracking income and expenses, invoicing, managing payroll, and creating reports. These full-featured and highly mature programs don't come cheap. Acclivity AccountEdge Pro, at $299, is the least expensive; and prices climb if you opt to use common time-saving add-ons such as payroll services, or if you add licenses for multiple user accounts. All three are solid on the basics, but they have distinct differences in style and focus. The more you know about your accounting requirements, the more closely you'll want to look at the software you're thinking of buying. Sage 50 Complete should appeal most to people who understand the fine points of accounting and can use the product's many customization features (especially for businesses that manage inventory). QuickBooks works hard to appeal to newbies who need only the basics and might be intimidated by the level of detail and technical language exposed in the other two packages. At the same time, it also has a slew of third-party add-ons that meet specific needs and greatly expand its capabilities. AccountEdge Pro balances accessibility with a strong feature set at an affordable price. It's especially suitable for businesses that need to provide simultaneous access to multiple users.

  Read the article

• What router hardware or software should be used when multiple public IPs are routed into the same LAN?

  - by lcbrevard

  I am looking for recommendations to replace a set of consumer grade (Linksys, Netgear, Belkin) routers with something that can handle more traffic while routing more than one static public IP into the same LAN address space. We have a block of static public IPs, 5 usable, with Comcast Business. Currently four of them are in use for: General office access Web server Mail and DNS servers Download and backup web server for separate business All systems (a mixture of physical and virtual) are in the same LAN address space (10.x.y.0/24) to enable easy access between them inside the office. There are 30 or more systems in use depending on which virtual machines are currently active. We have a mixture of Windows, Linux, FreeBSD, and Solaris. Currently a separate consumer grade router is used for each of the four static addresses, with its WAN address set to the specific static address and a different gateway address for each: uses 10.x.y.1 - various ports are forwarded to various LAN IPs on systems with gateway 10.x.y.1 uses 10.x.y.254 - port 80 is forwarded to a server with gateway 10.x.y.254 uses 10.x.y.253 - ports for mail and dns are forwarded to a server with gateway 10.x.y.253 uses 10.x.y.252 - ports as needed are forwarded to server with gateway 10.x.y.252 Only router 1. is allowed to serve DHCP and address reservation based on the MAC is used for most of the internal "server" IP addresses so they are at fixed values. [Some are set static due to limitations in the address reservation capabilities of router 1.] And, yes, this really does work! But... I am looking for: better DHCP with more capable address reservation higher capacity so I don't have to periodically power cycle the routers One obvious improvement would be to have a real DHCP server and not use a consumer grade router for that purpose. I am torn between buying a "professional" router such as Cisco or Juniper or Sonic Wall verus learning to configure some spare hardware to perform this function. The price goes up extremely rapidly with capabilities for commercial routers! Worse, some routers require licensing based on the number of clients - a disaster in our environment with so many virtual machines. Sorry for such a long posting but I am getting tired of having to power cycle routers and deal with shifting IP addresses afterwards!

  Read the article

• Cooling Server Rack with Water? Sensible? Reuse energy for small installation?

  - by TomTom

  First - this is not a shopping question, this is not so much about concrete prices but about general feasibility. Makes no sense to get looking fo ra manufacturer it the approach is bad. I am moving my company to new Offices in September, and among them we will expand and consolidate our number crunch cluster. It is so far in a data center. I have a nice room in the basement prepared now. I think about cooling. We will likely run up a power usage of around 10kw by end of the year. That is a LOT of stuff, and cooling will be expensive. I am located in south Poland, close to the German border. This is an area where water is available for relatively cheap price - "wasting water" is not a concern here. My situation is thus a lot different for example than in Spain ;) Physics tells me that to heat 1 liter of water by 1 degree I use 1 Calorie (1KCal), and a kwh power is (and we can assume 100% efficiency - water heaters are pretty efficient) 750 Calories. That means that 1 KWH is 750 liter by 1 degree. 10kw and a 20 degree heat would mean that per hour I need 375 liters. That is 6.25 liters per minute and not WHAT much ;) We talk 270 cubic meters here. Even in summer, the significant underground pipes really cool down the water a LOT more ;) Question: This such an approach feasible? Anyone done that? We talk of a 10kw installation for now. Is it feasible to reuse that heat? The alternative is a decent cooling system that WILL use around 2.5kwh for running. Dropping the water would basically (a) get me a quite cold input compared to the outside air even in summer (I.e. a lower temperature medium to drop the heat in) and (b) replace the need to actually have the outside cooling (which may b problematic - if the air is 22 degree, that is a LOT to fight off, but OTOH the water will be quite cold). I also would possibly save the investment for the outside part of the cooling circuit. Now, second question - is there a feasible way to heat a house with that? ;) After all, brutally speaking, it is a LOT of energy in that water ;) If it is a bad idea, I stop here - if it is not, I start looking for suppliers. Maybe my math is wrong?

  Read the article

• Reviews Cheyney Group Marketing: What accounting softwares are available in the market for small businesses?

  - by user224313

  Accounting is the language of business, and good accounting software can save you hundreds of hours at the business equivalent of Berlitz. There's no substitute for an accounting pro who knows the ins and outs of tax law, but today's desktop packages can help you with everything from routine bookkeeping to payroll, taxes, and planning. Each package also produces files that you can hand off to an accountant as needed. Small-business managers have more accounting software options than ever, including subscription Web-based options that don't require their users to install or update software. Many businesses, however--including those that need to track large inventories or client databases, and those that prefer not to entrust their data to the cloud--may be happier with a desktop tool. We looked at three general-purpose, small-business accounting packages: Acclivity AccountEdgePro 2012 (both the product and the company were previously called MYOB), Intuit QuickBooks Premier 2012, and Sage's Sage 50 Complete 2013 (the successor to Peachtree Complete). All three packages offer a solid array of tools for tracking income and expenses, invoicing, managing payroll, and creating reports. These full-featured and highly mature programs don't come cheap. Acclivity AccountEdge Pro, at $299, is the least expensive; and prices climb if you opt to use common time-saving add-ons such as payroll services, or if you add licenses for multiple user accounts. All three are solid on the basics, but they have distinct differences in style and focus. The more you know about your accounting requirements, the more closely you'll want to look at the software you're thinking of buying. Sage 50 Complete should appeal most to people who understand the fine points of accounting and can use the product's many customization features (especially for businesses that manage inventory). QuickBooks works hard to appeal to newbies who need only the basics and might be intimidated by the level of detail and technical language exposed in the other two packages. At the same time, it also has a slew of third-party add-ons that meet specific needs and greatly expand its capabilities. AccountEdge Pro balances accessibility with a strong feature set at an affordable price. It's especially suitable for businesses that need to provide simultaneous access to multiple users.

  Read the article

• [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

  - by Beco

  I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

  Read the article

• XNA Notes 009

  - by George Clingerman

  This past week the MVPs (myself included) were on Microsoft campus for the MVP summit. So I apologize in advance if you did something cool or heard of something cool happening with XNA and XBLIGs and it’s not in my notes. I did my best to stay on top of things, but honestly this community is fast and furious with what it’s doing and creating. I really can’t keep up and that’s fantastic! But here’s what I *did* notice while I was there on Microsoft Campus (and I did make sure to point out to the XNA team several of these very cool happenings while I had their ears). Time Critical XNA News: The XNA team wants you to know that Dream Build Play registration is now open! http://blogs.msdn.com/b/xna/archive/2011/02/28/registration-now-open-for-dream-build-play-2011-challenge.aspx Join the XNA-UK create on March 24, 2011 at the Microsoft Tech Days Conference http://xna-uk.net/blogs/darkgenesis/archive/2011/02/27/join-the-xna-uk-crew-at-the-microsoft-tech-days-conference-on-24th-march-2011.aspx XNA Team: Shawn Hargreaves shares one of the coolest things that’s happened in the XNA community http://blogs.msdn.com/b/shawnhar/archive/2011/03/02/xbox-indies-pivot-view.aspx Nick Gravelyn continues his unique marketing/work prioritization strategy as he tries to get to 5,000 Pixel Man users before he makes Pixel Man 2 (and he’s almost there!) http://nickgravelyn.com/pixelman2/ XNA MVPs: A lot of the XNA MVPs were at the Microsoft MVP Summit 2011. Due to NDAs, most things can’t be shared, but I’m sure if you’re curious you could ask them about the general vibe and feeling they got from the team and the future of XNA/XBLIG and more. Catalin Zima and team release the free WP7 game Chickens Can Dream http://twitter.com/CatalinZima/statuses/41174062923390976 http://www.amusedsloth.com/2011/02/chickens-can-dream-is-live/ Charles Humphrey (NemoKrad) posts his March talk source and PowerPoint http://xna-uk.net/blogs/randomchaos/archive/2011/03/04/march-2011-talk-post-processing-framework.aspx XNA Developers: Michael B. McLaughlin posts about ANTS Memory Profile and creates a CheckMemoryAllocationGame sample (extremely useful if you’re looking to see how much memory some operation allocates!) http://geekswithblogs.net/mikebmcl/archive/2011/02/28/ants-memory-profiler-7.0-review.aspx http://geekswithblogs.net/mikebmcl/archive/2011/03/01/checkmemoryallocationgame-sample.aspx Andy Schatz (2009 IGF winner for Monaco) talking XNA at GDC 2011 http://www.gamasutra.com/view/news/33313/GDC_2011_Andy_Schatz_Ill_Make_My_Last_Game_When_I_Die.php Xbox LIVE Indie Games (XBLIG): Clover: A Curious Tale by BinaryTweed is coming as a Deal of the Week during St. Patricks Day http://majornelson.com/archive/2011/03/03/comingsoontothexboxlivemarketplacemarchthird.aspx Ska Studios away at GDC but still very post happy as always http://www.ska-studios.com/2011/03/02/swamped-picture-pack/ http://www.ska-studios.com/2011/02/28/the-february-showcase/ http://www.ska-studios.com/2011/02/25/good-morning-gato-51-smelling-the-roses/ Just Press Start interviews Matthew Mikuszewski of Darkwind Media about Blocks Indie http://justpressstart.net/?p=516 Gamergeddon Xbox Indie Game Round Up - February 27th http://www.gamergeddon.com/2011/02/27/xbox-indie-game-round-up-february-27th/ http://www.gamergeddon.com/category/xbox-360/indie-games/ GameMarx does a round up of all the Xbox Live Indie Game podcasts that are currently available http://www.gamemarx.com/news/2011/02/27/xbox-live-indie-game-podcasts.aspx GameMarx episode 11 http://www.gamemarx.com/video/the-show/26/ep-11-february-25-2011.aspx In perhaps what I feel is the most exciting news I’ve heard all week, Michael C. Neel (ViNull of GameMarx fame) re-launch XboxIndies.com! http://www.gamemarx.com/news/2011/03/01/the-relaunch-of-xboxindies-com.aspx http://xboxindies.com/ Armless Octopus shares a little of what they heard from Luke Schneider of Radiangames during his GDC 2011 talk http://www.armlessoctopus.com/2011/03/02/gdc-2011-luke-schneider-offers-insight-into-radiangames-success/ VVGindiecast Episode 1 with guests Derek Strickland(Mr_Deeke), Kris Steele(Kriswd40 from FunInfused Games) and Dave Voyles(From armlessoctopus.com) http://vvgtv.com/2011/02/25/vvgindiecast-xblig-podcast/ If you’re doing Xbox LIVE Indie Game Reviews get in touch with XboxIndies.com to get into their aggregated feed http://forums.create.msdn.com/forums/p/76931/467189.aspx#467189 B.U.T.T.O.N and Flotilla represented XNA very well at the Independent Games Festival (are there any more games entered that were created using XNA? Stand up and be heard!) http://www.igf.com/php-bin/entry2011.php?id=374 Armless Ocotopus interview at GDC 2011 with Soulcaster creator Ian Stocker http://www.armlessoctopus.com/2011/03/04/gdc-2011-interview-with-soulcaster-creator-ian-stocker/ MommysBestGames gets a nod in the DarkBasic newsletter where it features the Explosionade Editor (just do a search for Explosionade to get to the interesting bits!) http://www.thegamecreators.com/pages/newsletters/newsletter_issue_98.html You may be hearing the cries of FortressCraft (coming soon to XBLIG) being so wrong for stealing the idea from MineCraft. But did you know the the game MineCraft started from was an XNA game called Infiniminer? XNA is getting it’s fingers into EVERYTHING! http://www.minecraftwiki.net/wiki/Infiniminer XNA Development: TorqueX is NOT dead thanks to the tremendous efforts of the XNA Community working on the CEV (special thanks to @PinoEire for all his hard work on making that happen!) http://www.garagegames.com/community/blogs/view/20878 http://torquecev.com/ Dave Henry has posted XNA 3.x adding platformer start kit to the network game state management on his new site http://twitter.com/#!/mort8088/status/43407715908853760 http://mort8088.com/2011/03/03/xna-3-x-adding-platformer-starter-kit-to-network-game-state-management/ Mark Bamford releases XNAViewer 4.0, great for running XNA games inside of a Windows Form (for building level editors, etc.) http://twitter.com/#!/xzodia04/status/43466830412660736 http://xnaviewer.codeplex.com/ Unit testing an XNA game with Resharper and NUnit http://smnbss.wordpress.com/2011/02/28/planetx-unit-testing-an-xna-game-with-resharper-and-nunit-wp7-xbox-xna/ XNA for Silverlight developers: Part 5 - Input (touch + gestures) http://ht.ly/1bxwUE Mike McLaughlin shares a link he stumbled across for those looking to understand vector and matrix math http://twitter.com/#!/mikebmcl/status/42587074725036032 http://chortle.ccsu.edu/VectorLessons/vectorIndex.html DigitalRune Resources Pooling in XNA (Part 1) http://www.digitalrune.com/Support/Blog/tabid/719/EntryId/84/DigitalRune-Helper-Library-Resource-Pooling-in-XNA-Part-1.aspx JohnK “bobthecbuilder” released a new SunBurn Update that lowers the requirements for Windows Games http://twitter.com/#!/bobthecbuilder/status/43457306578522112 http://www.synapsegaming.com/blogs/johnk/archive/2011/03/03/sunburn-update-windows-redistributable.aspx Quick update on the Indiefreaks Game Framework v0.4 development status http://indiefreaks.com/2011/03/04/quick-update-on-igf-v0-4-development/

  Read the article

• Windows Azure: Announcing Support for Windows Server 2012 R2 + Some Nice Price Cuts

  - by ScottGu

  Today we released some great updates to Windows Azure: Virtual Machines: Support for Windows Server 2012 R2 Cloud Services: Support for Windows Server 2012 R2 and .NET 4.5.1 Windows Azure Pack: Use Windows Azure features on-premises using Windows Server 2012 R2 Price Cuts: Up to 22% Price Reduction on Memory-Intensive Instances Below are more details about each of the improvements: Virtual Machines: Support for Windows Server 2012 R2 This morning we announced the release of Windows Server 2012 R2 – which is a fantastic update to Windows Server and includes a ton of great enhancements. This morning we are also excited to announce that the general availability image of Windows Server 2012 RC is now supported on Windows Azure.  Windows Azure is the first cloud provider to offer the final release of Windows Server 2012 R2, and it is incredibly easy to launch your own Windows Server 2012 R2 instance with it. To create a new Windows Server 2012 R2 instance simply choose New->Compute->Virtual Machine within the Windows Azure Management Portal.  You can select the “Windows Server 2012 R2” image and create a new Virtual Machine using the “Quick Create” option: Or alternatively click the “From Gallery” option if you want to customize even more configuration options (endpoints, remote powershell, availability set, etc): Creating and instantiating a new Virtual Machine on Windows Azure is very fast.  In fact, the Windows Server 2012 R2 image now deploys and runs 30% faster than previous versions of Windows Server. Once the VM is deployed you can drill into it to track its health and manage its settings: Clicking the “Connect” button allows you to remote desktop into the VM – at which point you can customize and manage it as a full administrator however you want: If you haven’t tried Windows Server 2012 R2 yet – give it a try with Windows Azure.  There is no easier way to get an instance of it up and running! Cloud Services: Support for using Windows Server 2012 R2 with Web and Worker Roles Today’s Windows Azure release also allows you to now use Windows Server 2012 R2 and .NET 4.5.1 within Web and Worker Roles within Cloud Service based applications.  Enabling this is easy.  You can configure existing existing Cloud Service application to use Windows Server 2012 R2 by updating your Cloud Service Configuration File (.cscfg) to use the new “OS Family 4” setting: Or alternatively you can use the Windows Azure Management Portal to update cloud services that are already deployed on Windows Azure.  Simply choose the configure tab on them and select Windows Server 2012 R2 in the Operating System Family dropdown: The approaches above enable you to immediately take advantage of Windows Server 2012 R2 and .NET 4.5.1 and all the great features they provide. Windows Azure Pack: Use Windows Azure features on Windows Server 2012 R2 Today we also made generally available the Windows Azure Pack, which is a free download that enables you to run Windows Azure Technology within your own datacenter, an on-premises private cloud environment, or with one of our service provider/hosting partners who run Windows Server. Windows Azure Pack enables you to use a management portal that has the exact same UI as the Windows Azure Management Portal, and within which you can create and manage Virtual Machines, Web Sites, and Service Bus – all of which can run on Windows Server and System Center.  The services provided with the Windows Azure Pack are consistent with the services offered within our Windows Azure public cloud offering.  This consistency enables organizations and developers to build applications and solutions that can run in any hosting environment – and which use the same development and management approach.  The end result is an offering with incredible flexibility. You can learn more about Windows Azure Pack and download/deploy it today here. Price Cuts: Up to 22% Reduction on Memory Intensive Instances Today we are also reducing prices by up to 22% on our memory-intensive VM instances (specifically our A5, A6, and A7 instances).  These price reductions apply to both Windows and Linux VM instances, as well as for Cloud Service based applications: These price reductions will take effect in November, and will enable you to run applications that demand larger memory (such as SharePoint, Databases, in-memory analytics, etc) even more cost effectively. Summary Today’s release enables you to start using Windows Server 2012 R2 within Windows Azure immediately, and take advantage of our Cloud OS vision both within our datacenters – and using the Windows Azure Pack within both your existing datacenters and those of our partners. If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using all of the above features today.  Then visit the Windows Azure Developer Center to learn more about how to build apps with it. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Creating packages in code – Execute SQL Task

  The Execute SQL Task is for obvious reasons very well used, so I thought if you are building packages in code the chances are you will be using it. Using the task basic features of the task are quite straightforward, add the task and set some properties, just like any other. When you start interacting with variables though it can be a little harder to grasp so these samples should see you through. Some of these more advanced features are explained in much more detail in our ever popular post The Execute SQL Task, here I’ll just be showing you how to implement them in code. The abbreviated code blocks below demonstrate the different features of the task. The complete code has been encapsulated into a sample class which you can download (ExecSqlPackage.cs). Each feature described has its own method in the sample class which is mentioned after the code block. This first sample just shows adding the task, setting the basic properties for a connection and of course an SQL statement. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Set required properties taskHost.Properties["Connection"].SetValue(taskHost, sqlConnection.ID); taskHost.Properties["SqlStatementSource"].SetValue(taskHost, "SELECT * FROM sysobjects"); For the full version of this code, see the CreatePackage method in the sample class. The AddSqlConnection method is a helper method that adds an OLE-DB connection to the package, it is of course in the sample class file too. Returning a single value with a Result Set The following sample takes a different approach, getting a reference to the ExecuteSQLTask object task itself, rather than just using the non-specific TaskHost as above. Whilst it means we need to add an extra reference to our project (Microsoft.SqlServer.SQLTask) it makes coding much easier as we have compile time validation of any property and types we use. For the more complex properties that is very valuable and saves a lot of time during development. The query has also been changed to return a single value, one row and one column. The sample shows how we can return that value into a variable, which we also add to our package in the code. To do this manually you would set the Result Set property on the General page to Single Row and map the variable on the Result Set page in the editor. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Add variable to hold result value package.Variables.Add("Variable", false, "User", 0); // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = 'sysrowsets'"; // Set single row result set task.ResultSetType = ResultSetType.ResultSetType_SingleRow; // Add result set binding, map the id column to variable task.ResultSetBindings.Add(); IDTSResultBinding resultBinding = task.ResultSetBindings.GetBinding(0); resultBinding.ResultName = "id"; resultBinding.DtsVariableName = "User::Variable"; For the full version of this code, see the CreatePackageResultVariable method in the sample class. The other types of Result Set behaviour are just a variation on this theme, set the property and map the result binding as required. Parameter Mapping for SQL Statements This final example uses a parameterised SQL statement, with the coming from a variable. The syntax varies slightly between connection types, as explained in the Working with Parameters and Return Codes in the Execute SQL Taskhelp topic, but OLE-DB is the most commonly used, for which a question mark is the parameter value placeholder. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, ".", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = ?"; // Add variable to hold parameter value package.Variables.Add("Variable", false, "User", "sysrowsets"); // Add input parameter binding task.ParameterBindings.Add(); IDTSParameterBinding parameterBinding = task.ParameterBindings.GetBinding(0); parameterBinding.DtsVariableName = "User::Variable"; parameterBinding.ParameterDirection = ParameterDirections.Input; parameterBinding.DataType = (int)OleDBDataTypes.VARCHAR; parameterBinding.ParameterName = "0"; parameterBinding.ParameterSize = 255; For the full version of this code, see the CreatePackageParameterVariable method in the sample class. You’ll notice the data type has to be specified for the parameter IDTSParameterBinding .DataType Property, and these type codes are connection specific too. My enumeration I wrote several years ago is shown below was probably done by reverse engineering a package and also the API header file, but I recently found a very handy post that covers more connections as well for exactly this, Setting the DataType of IDTSParameterBinding objects (Execute SQL Task). /// <summary> /// Enumeration of OLE-DB types, used when mapping OLE-DB parameters. /// </summary> private enum OleDBDataTypes { BYTE = 0x11, CURRENCY = 6, DATE = 7, DB_VARNUMERIC = 0x8b, DBDATE = 0x85, DBTIME = 0x86, DBTIMESTAMP = 0x87, DECIMAL = 14, DOUBLE = 5, FILETIME = 0x40, FLOAT = 4, GUID = 0x48, LARGE_INTEGER = 20, LONG = 3, NULL = 1, NUMERIC = 0x83, NVARCHAR = 130, SHORT = 2, SIGNEDCHAR = 0x10, ULARGE_INTEGER = 0x15, ULONG = 0x13, USHORT = 0x12, VARCHAR = 0x81, VARIANT_BOOL = 11 } Download Sample code ExecSqlPackage.cs (10KB)

  Read the article

• Parallelism in .NET – Part 12, More on Task Decomposition

  - by Reed

  Many tasks can be decomposed using a Data Decomposition approach, but often, this is not appropriate.  Frequently, decomposing the problem into distinctive tasks that must be performed is a more natural abstraction. However, as I mentioned in Part 1, Task Decomposition tends to be a bit more difficult than data decomposition, and can require a bit more effort.  Before we being parallelizing our algorithm based on the tasks being performed, we need to decompose our problem, and take special care of certain considerations such as ordering and grouping of tasks. Up to this point in this series, I’ve focused on parallelization techniques which are most appropriate when a problem space can be decomposed by data.  Using PLINQ and the Parallel class, I’ve shown how problem spaces where there is a collection of data, and each element needs to be processed, can potentially be parallelized. However, there are many other routines where this is not appropriate.  Often, instead of working on a collection of data, there is a single piece of data which must be processed using an algorithm or series of algorithms.  Here, there is no collection of data, but there may still be opportunities for parallelism. As I mentioned before, in cases like this, the approach is to look at your overall routine, and decompose your problem space based on tasks.  The idea here is to look for discrete “tasks,” individual pieces of work which can be conceptually thought of as a single operation. Let’s revisit the example I used in Part 1, an application startup path.  Say we want our program, at startup, to do a bunch of individual actions, or “tasks”.  The following is our list of duties we must perform right at startup: Display a splash screen Request a license from our license manager Check for an update to the software from our web server If an update is available, download it Setup our menu structure based on our current license Open and display our main, welcome Window Hide the splash screen The first step in Task Decomposition is breaking up the problem space into discrete tasks. This, naturally, can be abstracted as seven discrete tasks.  In the serial version of our program, if we were to diagram this, the general process would appear as: These tasks, obviously, provide some opportunities for parallelism.  Before we can parallelize this routine, we need to analyze these tasks, and find any dependencies between tasks.  In this case, our dependencies include: The splash screen must be displayed first, and as quickly as possible. We can’t download an update before we see whether one exists. Our menu structure depends on our license, so we must check for the license before setting up the menus. Since our welcome screen will notify the user of an update, we can’t show it until we’ve downloaded the update. Since our welcome screen includes menus that are customized based off the licensing, we can’t display it until we’ve received a license. We can’t hide the splash until our welcome screen is displayed. By listing our dependencies, we start to see the natural ordering that must occur for the tasks to be processed correctly. The second step in Task Decomposition is determining the dependencies between tasks, and ordering tasks based on their dependencies. Looking at these tasks, and looking at all the dependencies, we quickly see that even a simple decomposition such as this one can get quite complicated.  In order to simplify the problem of defining the dependencies, it’s often a useful practice to group our tasks into larger, discrete tasks.  The goal when grouping tasks is that you want to make each task “group” have as few dependencies as possible to other tasks or groups, and then work out the dependencies within that group.  Typically, this works best when any external dependency is based on the “last” task within the group when it’s ordered, although that is not a firm requirement.  This process is often called Grouping Tasks.  In our case, we can easily group together tasks, effectively turning this into four discrete task groups: 1. Show our splash screen – This needs to be left as its own task.  First, multiple things depend on this task, mainly because we want this to start before any other action, and start as quickly as possible. 2. Check for Update and Download the Update if it Exists - These two tasks logically group together.  We know we only download an update if the update exists, so that naturally follows.  This task has one dependency as an input, and other tasks only rely on the final task within this group. 3. Request a License, and then Setup the Menus – Here, we can group these two tasks together.  Although we mentioned that our welcome screen depends on the license returned, it also depends on setting up the menu, which is the final task here.  Setting up our menus cannot happen until after our license is requested.  By grouping these together, we further reduce our problem space. 4. Display welcome and hide splash - Finally, we can display our welcome window and hide our splash screen.  This task group depends on all three previous task groups – it cannot happen until all three of the previous groups have completed. By grouping the tasks together, we reduce our problem space, and can naturally see a pattern for how this process can be parallelized.  The diagram below shows one approach: The orange boxes show each task group, with each task represented within.  We can, now, effectively take these tasks, and run a large portion of this process in parallel, including the portions which may be the most time consuming.  We’ve now created two parallel paths which our process execution can follow, hopefully speeding up the application startup time dramatically. The main point to remember here is that, when decomposing your problem space by tasks, you need to: Define each discrete action as an individual Task Discover dependencies between your tasks Group tasks based on their dependencies Order the tasks and groups of tasks

  Read the article

• Parallelism in .NET – Part 1, Decomposition

  - by Reed

  The first step in designing any parallelized system is Decomposition.  Decomposition is nothing more than taking a problem space and breaking it into discrete parts.  When we want to work in parallel, we need to have at least two separate things that we are trying to run.  We do this by taking our problem and decomposing it into parts. There are two common abstractions that are useful when discussing parallel decomposition: Data Decomposition and Task Decomposition.  These two abstractions allow us to think about our problem in a way that helps leads us to correct decision making in terms of the algorithms we’ll use to parallelize our routine. To start, I will make a couple of minor points. I’d like to stress that Decomposition has nothing to do with specific algorithms or techniques.  It’s about how you approach and think about the problem, not how you solve the problem using a specific tool, technique, or library.  Decomposing the problem is about constructing the appropriate mental model: once this is done, you can choose the appropriate design and tools, which is a subject for future posts. Decomposition, being unrelated to tools or specific techniques, is not specific to .NET in any way.  This should be the first step to parallelizing a problem, and is valid using any framework, language, or toolset.  However, this gives us a starting point – without a proper understanding of decomposition, it is difficult to understand the proper usage of specific classes and tools within the .NET framework. Data Decomposition is often the simpler abstraction to use when trying to parallelize a routine.  In order to decompose our problem domain by data, we take our entire set of data and break it into smaller, discrete portions, or chunks.  We then work on each chunk in the data set in parallel. This is particularly useful if we can process each element of data independently of the rest of the data.  In a situation like this, there are some wonderfully simple techniques we can use to take advantage of our data.  By decomposing our domain by data, we can very simply parallelize our routines.  In general, we, as developers, should be always searching for data that can be decomposed. Finding data to decompose if fairly simple, in many instances.  Data decomposition is typically used with collections of data.  Any time you have a collection of items, and you’re going to perform work on or with each of the items, you potentially have a situation where parallelism can be exploited.  This is fairly easy to do in practice: look for iteration statements in your code, such as for and foreach. Granted, every for loop is not a candidate to be parallelized.  If the collection is being modified as it’s iterated, or the processing of elements depends on other elements, the iteration block may need to be processed in serial.  However, if this is not the case, data decomposition may be possible. Let’s look at one example of how we might use data decomposition.  Suppose we were working with an image, and we were applying a simple contrast stretching filter.  When we go to apply the filter, once we know the minimum and maximum values, we can apply this to each pixel independently of the other pixels.  This means that we can easily decompose this problem based off data – we will do the same operation, in parallel, on individual chunks of data (each pixel). Task Decomposition, on the other hand, is focused on the individual tasks that need to be performed instead of focusing on the data.  In order to decompose our problem domain by tasks, we need to think about our algorithm in terms of discrete operations, or tasks, which can then later be parallelized. Task decomposition, in practice, can be a bit more tricky than data decomposition.  Here, we need to look at what our algorithm actually does, and how it performs its actions.  Once we have all of the basic steps taken into account, we can try to analyze them and determine whether there are any constraints in terms of shared data or ordering.  There are no simple things to look for in terms of finding tasks we can decompose for parallelism; every algorithm is unique in terms of its tasks, so every algorithm will have unique opportunities for task decomposition. For example, say we want our software to perform some customized actions on startup, prior to showing our main screen.  Perhaps we want to check for proper licensing, notify the user if the license is not valid, and also check for updates to the program.  Once we verify the license, and that there are no updates, we’ll start normally.  In this case, we can decompose this problem into tasks – we have a few tasks, but there are at least two discrete, independent tasks (check licensing, check for updates) which we can perform in parallel.  Once those are completed, we will continue on with our other tasks. One final note – Data Decomposition and Task Decomposition are not mutually exclusive.  Often, you’ll mix the two approaches while trying to parallelize a single routine.  It’s possible to decompose your problem based off data, then further decompose the processing of each element of data based on tasks.  This just provides a framework for thinking about our algorithms, and for discussing the problem.

  Read the article

• Creating packages in code – Execute SQL Task

  The Execute SQL Task is for obvious reasons very well used, so I thought if you are building packages in code the chances are you will be using it. Using the task basic features of the task are quite straightforward, add the task and set some properties, just like any other. When you start interacting with variables though it can be a little harder to grasp so these samples should see you through. Some of these more advanced features are explained in much more detail in our ever popular post The Execute SQL Task, here I’ll just be showing you how to implement them in code. The abbreviated code blocks below demonstrate the different features of the task. The complete code has been encapsulated into a sample class which you can download (ExecSqlPackage.cs). Each feature described has its own method in the sample class which is mentioned after the code block. This first sample just shows adding the task, setting the basic properties for a connection and of course an SQL statement. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Set required properties taskHost.Properties["Connection"].SetValue(taskHost, sqlConnection.ID); taskHost.Properties["SqlStatementSource"].SetValue(taskHost, "SELECT * FROM sysobjects"); For the full version of this code, see the CreatePackage method in the sample class. The AddSqlConnection method is a helper method that adds an OLE-DB connection to the package, it is of course in the sample class file too. Returning a single value with a Result Set The following sample takes a different approach, getting a reference to the ExecuteSQLTask object task itself, rather than just using the non-specific TaskHost as above. Whilst it means we need to add an extra reference to our project (Microsoft.SqlServer.SQLTask) it makes coding much easier as we have compile time validation of any property and types we use. For the more complex properties that is very valuable and saves a lot of time during development. The query has also been changed to return a single value, one row and one column. The sample shows how we can return that value into a variable, which we also add to our package in the code. To do this manually you would set the Result Set property on the General page to Single Row and map the variable on the Result Set page in the editor. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, "localhost", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Add variable to hold result value package.Variables.Add("Variable", false, "User", 0); // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = 'sysrowsets'"; // Set single row result set task.ResultSetType = ResultSetType.ResultSetType_SingleRow; // Add result set binding, map the id column to variable task.ResultSetBindings.Add(); IDTSResultBinding resultBinding = task.ResultSetBindings.GetBinding(0); resultBinding.ResultName = "id"; resultBinding.DtsVariableName = "User::Variable"; For the full version of this code, see the CreatePackageResultVariable method in the sample class. The other types of Result Set behaviour are just a variation on this theme, set the property and map the result binding as required. Parameter Mapping for SQL Statements This final example uses a parameterised SQL statement, with the coming from a variable. The syntax varies slightly between connection types, as explained in the Working with Parameters and Return Codes in the Execute SQL Taskhelp topic, but OLE-DB is the most commonly used, for which a question mark is the parameter value placeholder. Package package = new Package(); // Add the SQL OLE-DB connection ConnectionManager sqlConnection = AddSqlConnection(package, ".", "master"); // Add the SQL Task package.Executables.Add("STOCK:SQLTask"); // Get the task host wrapper TaskHost taskHost = package.Executables[0] as TaskHost; // Get the task object ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask; // Set core properties task.Connection = sqlConnection.Name; task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = ?"; // Add variable to hold parameter value package.Variables.Add("Variable", false, "User", "sysrowsets"); // Add input parameter binding task.ParameterBindings.Add(); IDTSParameterBinding parameterBinding = task.ParameterBindings.GetBinding(0); parameterBinding.DtsVariableName = "User::Variable"; parameterBinding.ParameterDirection = ParameterDirections.Input; parameterBinding.DataType = (int)OleDBDataTypes.VARCHAR; parameterBinding.ParameterName = "0"; parameterBinding.ParameterSize = 255; For the full version of this code, see the CreatePackageParameterVariable method in the sample class. You’ll notice the data type has to be specified for the parameter IDTSParameterBinding .DataType Property, and these type codes are connection specific too. My enumeration I wrote several years ago is shown below was probably done by reverse engineering a package and also the API header file, but I recently found a very handy post that covers more connections as well for exactly this, Setting the DataType of IDTSParameterBinding objects (Execute SQL Task). /// <summary> /// Enumeration of OLE-DB types, used when mapping OLE-DB parameters. /// </summary> private enum OleDBDataTypes { BYTE = 0x11, CURRENCY = 6, DATE = 7, DB_VARNUMERIC = 0x8b, DBDATE = 0x85, DBTIME = 0x86, DBTIMESTAMP = 0x87, DECIMAL = 14, DOUBLE = 5, FILETIME = 0x40, FLOAT = 4, GUID = 0x48, LARGE_INTEGER = 20, LONG = 3, NULL = 1, NUMERIC = 0x83, NVARCHAR = 130, SHORT = 2, SIGNEDCHAR = 0x10, ULARGE_INTEGER = 0x15, ULONG = 0x13, USHORT = 0x12, VARCHAR = 0x81, VARIANT_BOOL = 11 } Download Sample code ExecSqlPackage.cs (10KB)

  Read the article

• Kaiden and the Arachnoid Cyst

  - by Martin Hinshelwood

  Some of you may remember when my son Kaiden was born I posted pictures of him and his sister. Kaiden is now 15 months old and is progressing perfectly in every area except that and we had been worried that he was not walking yet. We were only really concerned as his sister was walking at 8 months. Figure: Kai as his usual self   Jadie and I were concerned over that and that he had a rather large head (noggin) so we talked to various GP’s and our health visitor who immediately dismissed our concerns every time. That was until about two months ago when we happened to get a GP whose daughter had Hyper Mobility and she recognised the symptoms immediately. We were referred to the Southbank clinic who were lovely and the paediatrician confirmed that he had Hyper Mobility after testing all of his faculties. This just means that his joints are overly mobile and would need a little physiotherapy to help him out. At the end the paediatrician remarked offhand that he has a rather large head and wanted to measure it. Sure enough he was a good margin above the highest percentile mark for his height and weight. The paediatrician showed the measurements to a paediatric consultant who, as a precautionary measure, referred us for an MRI at Yorkhill Children's hospital. Now, Yorkhill has always been fantastic to us, and this was no exception. You know we have NEVER had a correct diagnosis for the kids (with the exception of the above) from a GP and indeed twice have been proscribed incorrect medication that made the kids sicker! We now always go strait to Yorkhill to save them having to fix GP mistakes as well. Monday 24th May, 7pm The scan went fantastically, with Kaiden sleeping in the MRI machine for all but 5 minutes at the end where he waited patiently for it to finish. We were not expecting anything to be wrong as this was just a precautionary scan to make sure that nothing in his head was affecting his gross motor skills. After the scan we were told to expect a call towards the end of the week… Tuesday 25th May, 12pm The very next day we got a call from Southbank who said that they has found an Arachnoid Cyst and could we come in the next day to see a Consultant and that Kai would need an operation. Wednesday 26th May, 12:30pm We went into the Southbank clinic and spoke to the paediatric consultant who assured us that it was operable but that it was taking up considerable space in Kai’s head. Cerebrospinal fluid is building up as a cyst is blocking the channels it uses to drain. Thankfully they told us that prospects were good and that Kai would expect to make a full recovery before showing us the MRI pictures. Figure: Normal brain MRI cross section. This normal scan shows the spaces in the middle of the brain that contain and produce the Cerebrospinal fluid. Figure: Normal Cerebrospinal Flow This fluid is needed by the brain but is drained in the middle down the spinal column. Figure: Kai’s cyst blocking the four channels. I do not think that I need to explain the difference between the healthy picture and Kai’s picture. However you can see in this first picture the faint outline of the cyst in the middle that is blocking the four channels from draining. After seeing the scans a Neurosurgeon has decided that he is not acute, but needs an operation to unblock the flow. Figure: OMFG! You can see in the second picture the effect of the build up of fluid. If I was not horrified by the first picture I was seriously horrified by this one. What next? Kai is not presenting the symptoms of vomiting or listlessness that would show an immediate problem and as such we will get an appointment to see the Paediatric Neurosurgeon at the Southern General hospital in about 4 weeks. This timescale is based on the Neurosurgeon seeing the scans. After that Kai will need an operation to release the pressure and either remove the cyst completely or put in a permanent shunt (tube from brain to stomach) to bypass the blockage. We have updated his notes for the referral with additional recent information on top of the scan that the consultant things will help improve the timescales, but that is just a guess.   All we can do now is wait and see, and be watchful for tell tail signs of listlessness, eye problems and vomiting that would signify a worsening of his condition.   Technorati Tags: Personal

  Read the article

< Previous Page | 282 283 284 285 286 287 288 289 290 291 292 293  | Next Page >