Search Results

Search found 7782 results on 312 pages for 'label statements'.

Page 287/312 | < Previous Page | 283 284 285 286 287 288 289 290 291 292 293 294  | Next Page >

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• Persistent static routes fail on MacOS 10.6.5 startup!

  - by verbalicious

  I'm unable to get static routes to persist a reboot on Mac OS 10.6.5. I've tried all of the methods prescribed in Google search results, and previous posts on this site. I've tried manually creating a launchd daemon, and used RouteSplit's launchd daemon to no avail. It's clear that the interface is not ready when these methods attempt to apply the route. This workstation in question is getting its IP from DHCP and probably hasn't gotten its DHCP lease when the command runs. We're able to apply the route by hand when logged in, but not through startup methods. Is there another way to apply this route by sneaking the command into something later, but before the login window appears to the user? Here is some relevant log info from system.log. You can see the "route: writing to routing socket: Network is unreachable" errors where my launchd script fires off. I've tried adding extra "sleep" and "ipconfig waitall" statements later in the script but this doesn't fly. Dec 15 19:30:41 localhost com.apple.launchd[1]: *** launchd[1] has started up. *** Dec 15 19:30:45 localhost mDNSResponder[18]: mDNSResponder mDNSResponder-258.13 (Oct 8 2010 17:10:30) starting Dec 15 19:30:47 localhost configd[15]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50) Dec 15 19:30:47 localhost configd[15]: DHCP en1: INIT transmit failed Dec 15 19:30:47 localhost configd[15]: network configuration changed. Dec 15 19:30:47 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:30:47 Administrators-MacBook-Pro blued[16]: Apple Bluetooth daemon started Dec 15 19:30:52 Administrators-MacBook-Pro syslog[67]: routes.sh: Starting RouteSplit Dec 15 19:30:53 Administrators-MacBook-Pro com.apple.usbmuxd[41]: usbmuxd-207 built for iTunesTenOne on Oct 19 2010 at 13:50:35, running 64 bit Dec 15 19:30:54 Administrators-MacBook-Pro /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[50]: Login Window Application Started Dec 15 19:30:55 Administrators-MacBook-Pro bootlog[61]: BOOT_TIME: 1292459441 0 Dec 15 19:30:55 Administrators-MacBook-Pro syslog[86]: routes.sh: static route 192.168.0.0/23 192.168.2.2 Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: route: writing to routing socket: Network is unreachable Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: add net 192.168.0.0: gateway 192.168.2.2: Network is unreachable Dec 15 19:30:57 Administrators-MacBook-Pro org.apache.httpd[38]: httpd: Could not reliably determine the server's fully qualified domain name, using Administrators-MacBook-Pro.local for ServerName Dec 15 19:30:58 Administrators-MacBook-Pro loginwindow[50]: Login Window Started Security Agent Dec 15 19:30:58 Administrators-MacBook-Pro WindowServer[89]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:30:58 Administrators-MacBook-Pro com.apple.WindowServer[89]: Wed Dec 15 19:30:58 Administrators-MacBook-Pro.local WindowServer[89] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:31:18 Administrators-MacBook-Pro configd[15]: network configuration changed. Dec 15 19:31:19 administrators-macbook-pro configd[15]: setting hostname to "administrators-macbook-pro.local" Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[121]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000 Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.apple.com Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known Dec 15 19:31:27 administrators-macbook-pro configd[15]: network configuration changed. Dec 15 19:31:27 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:31:27 Administrators-MacBook-Pro ntpd[37]: Cannot find existing interface for address 17.151.16.20 Dec 15 19:31:27 Administrators-MacBook-Pro ntpd_initres[125]: ntpd indicates no data available! Dec 15 19:31:31 Administrators-MacBook-Pro sshd[128]: USER_PROCESS: 133 ttys000 Dec 15 19:31:37 Administrators-MacBook-Pro sudo[138]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/usr/bin/less /var/log/system.log ``You can see the following line in /var/log/kernel.log that shows the en0 interface coming up: Dec 15 19:30:51 Administrators-MacBook-Pro kernel[0]: Ethernet [AppleBCM5701Ethernet]: Link up on en0, 1-Gigabit, Full-duplex, No flow-control, Debug [796d,0f01,0de1,0300,c1e1,3800]

  Read the article

• LUKS with LVM, mount is not persistent after reboot

  - by linxsaga

  I have created a Logical vol and used luks to encrypt it. But while rebooting the server. I get a error message (below), therefore I would have to enter the root pass and disable the /etc/fstab entry. So mount of the LUKS partition is not persistent during reboot using LUKS. I have this setup on RHEL6 and wondering what i could be missing. I want to the LV to get be mount on reboot. Later I would want to replace it with UUID instead of the device name. Error message on reboot: "Give root password for maintenance (or type Control-D to continue):" Here are the steps from the beginning: [root@rhel6 ~]# pvcreate /dev/sdb Physical volume "/dev/sdb" successfully created [root@rhel6 ~]# vgcreate vg01 /dev/sdb Volume group "vg01" successfully created [root@rhel6 ~]# lvcreate --size 500M -n lvol1 vg01 Logical volume "lvol1" created [root@rhel6 ~]# lvdisplay --- Logical volume --- LV Name /dev/vg01/lvol1 VG Name vg01 LV UUID nX9DDe-ctqG-XCgO-2wcx-ddy4-i91Y-rZ5u91 LV Write Access read/write LV Status available # open 0 LV Size 500.00 MiB Current LE 125 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 [root@rhel6 ~]# cryptsetup luksFormat /dev/vg01/lvol1 WARNING! ======== This will overwrite data on /dev/vg01/lvol1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: [root@rhel6 ~]# mkdir /house [root@rhel6 ~]# cryptsetup luksOpen /dev/vg01/lvol1 house Enter passphrase for /dev/vg01/lvol1: [root@rhel6 ~]# mkfs.ext4 /dev/mapper/house mke2fs 1.41.12 (17-May-2010) Filesystem label= OS type: Linux Block size=1024 (log=0) Fragment size=1024 (log=0) Stride=0 blocks, Stripe width=0 blocks 127512 inodes, 509952 blocks 25497 blocks (5.00%) reserved for the super user First data block=1 Maximum filesystem blocks=67633152 63 block groups 8192 blocks per group, 8192 fragments per group 2024 inodes per group Superblock backups stored on blocks: 8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409 Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 21 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. [root@rhel6 ~]# mount -t ext4 /dev/mapper/house /house PS: HERE I have successfully mounted: [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# vim /etc/fstab -> as follow /dev/mapper/house /house ext4 defaults 1 2 [root@rhel6 ~]# vim /etc/crypttab -> entry as follows house /dev/vg01/lvol1 password [root@rhel6 ~]# mount -o remount /house [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# umount /house/ [root@rhel6 ~]# mount -a -> SUCCESSFUL AGAIN [root@rhel6 ~]# ls /house/ lost+found Please let me know if I am missing anything here. Thanks in advance.

  Read the article

• How to export computers from Active Directory to XML using Powershell?

  - by CoDeRs

  I am trying to create a powershell scripts for Remote Desktop Connection Manager using the active directory module. My first thought was get a list of computers in AD and parse them out into XML format similar to the OU structure that is in AD. I have no problem with that, the below code will work just but not how I wanted. EG # here is a the array $OUs Americas/Canada/Canada Computers/Desktops Americas/Canada/Canada Computers/Laptops Americas/Canada/Canada Computers/Virtual Computers Americas/USA/USA Computers/Laptops Computers Disabled Accounts Domain Controllers EMEA/UK/UK Computers/Desktops EMEA/UK/UK Computers/Laptops Outside Sales and Service/Laptops Servers I wanted to have the basic XML structured like this Americas Canada Canada Computers Desktops Laptops Virtual Computers USA USA Computers Laptops Computers Disabled Accounts Domain Controllers EMEA UK UK Computers Desktops Laptops Outside Sales and Service Laptops Servers However if you run the below it does not nest the next string in the array it only restarts the from the beginning and duplicating Americas Canada Canada Computers Desktops Americas Canada Canada Computers Laptops Americas Canada Canada Computers Virtual Computers Americas USA USA Computers Laptops RDCMGenerator.ps1 #Importing Microsoft`s PowerShell-module for administering ActiveDirectory Import-Module ActiveDirectory #Initial variables $OUs = @() $RDCMVer = "2.2" $userName = "domain\username" $password = "Hashed Password+" $Path = "$env:temp\test.xml" $allComputers = Get-ADComputer -LDAPFilter "(OperatingSystem=*)" -Properties Name,Description,CanonicalName | Sort-Object CanonicalName | select Name,Description,CanonicalName $allOUObjects = $allComputers | Foreach {"$($_.CanonicalName)"} Function Initialize-XML{ ##<RDCMan schemaVersion="1"> $xmlWriter.WriteStartElement('RDCMan') $XmlWriter.WriteAttributeString('schemaVersion', '1') $xmlWriter.WriteElementString('version',$RDCMVer) $xmlWriter.WriteStartElement('file') $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$env:userdomain) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('userName',$userName) $xmlWriter.WriteElementString('domain',$env:userdomain) $xmlWriter.WriteStartElement('password') $XmlWriter.WriteAttributeString('storeAsClearText', 'false') $XmlWriter.WriteRaw($password) $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('size','1024 x 768') $xmlWriter.WriteElementString('sameSizeAsClientArea','True') $xmlWriter.WriteElementString('fullScreen','False') $xmlWriter.WriteElementString('colorDepth','32') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Group ($groupName){ #Start Group $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$groupName) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Server ($computerName, $computerDescription) { #Start Server $xmlWriter.WriteStartElement('server') $xmlWriter.WriteElementString('name',$computerName) $xmlWriter.WriteElementString('displayName',$computerDescription) $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() #Stop Server } Function Close-XML { $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() # finalize the document: $xmlWriter.Flush() $xmlWriter.Close() notepad $path } #Strip out Domain and Computer Name from CanonicalName foreach($OU in $allOUObjects){ $newSplit = $OU.split("/") $rebildOU = "" for($i=1; $i -le ($newSplit.count - 2); $i++){ $rebildOU += $newSplit[$i] + "/" } $OUs += $rebildOU.substring(0,($rebildOU.length - 1)) } #Remove Duplicate OU's $OUs = $OUs | select -uniq #$OUs # get an XMLTextWriter to create the XML $XmlWriter = New-Object System.XMl.XmlTextWriter($Path,$UTF8) # choose a pretty formatting: $xmlWriter.Formatting = 'Indented' $xmlWriter.Indentation = 1 $XmlWriter.IndentChar = "`t" # write the header $xmlWriter.WriteStartDocument() # # 'encoding', 'utf-8' How? # # set XSL statements #Initialize Pre-Defined XML Initialize-XML ######################################################### # Start Loop for each OU-Path that has a computer in it ######################################################### foreach ($OU in $OUs){ $totalGroupName = "" #Create / Reset Total OU-Path Completed $OU.split("/") | foreach { #Split the OU-Path into individual OU's $groupName = "$_" #Current OU $totalGroupName += $groupName + "/" #Total OU-Path Completed $xmlWriter.WriteStartElement('group') #Start new XML Group Create-Group $groupName #Call function to create XML Group ################################################ # Start Loop for each Computer in $allComputers ################################################ foreach($computer in $allComputers){ $computerOU = $computer.CanonicalName #Set the computers OU-Path $OUSplit = $computerOU.split("/") #Create the Split for the OU-Path $rebiltOU = "" #Create / Reset the stripped OU-Path for($i=1; $i -le ($OUSplit.count - 2); $i++){ #Start Loop for OU-Path to strip out the Domain and Computer Name $rebiltOU += $OUSplit[$i] + "/" #Rebuild the stripped OU-Path } if ($rebiltOU -eq $totalGroupName){ #Compare the Current OU-Path with the computers stripped OU-Path $computerName = $computer.Name #Set the computer name $computerDescription = $computerName + " - " + $computer.Description #Set the computer Description Create-Server $computerName $computerDescription #Call function to create XML Server } } } ################################################### # Start Loop to close out XML Groups created above ################################################### $totalGroupName.split("/") | foreach { #Split the if ($_ -ne "" ){ $xmlWriter.WriteEndElement() #End Group } } } Close-XML

  Read the article

• OSX: Howto start VirtualBox VM on startup?

  - by snies

  The Question How do i start this Wiki VM at the startup of the OSX Server? I am running OSX Server 10.6.8 and VirtualBox 4.1.8 r75467 and a Debian Linux VM (called "wiki"). . What I tried so far Following this article: http://mikkel.hoegh.org/blog/2010/12/23/run-virtualbox-boot-mac-os-x/, i have wrote this plist and placed it in /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist: <plist version="1.0"> <dict> <key>Label</key> <string>bar.foo.WikiVirtualBox</string> <key>ProgramArguments</key> <array> <string>/usr/bin/VBoxHeadless</string> <string>-s</string> <string>wiki</string> </array> <key>RunAtLoad</key> <true></true> <key>UserName</key> <string>root</string> <key>WorkingDirectory</key> <string>/var/root</string> <key>StandardErrorPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stderr.log</string> <key>StandardOutPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stdout.log</string> </dict> </plist> and told launchd to start it: sudo launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist . The Logfile But the VM doesn't start. A Look at tail -f /var/log/system.log shows: sudo[1909]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/bin/launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist VBoxSVC[1914]: 3891612: (connectAndCheck) Untrusted apps are not allowed to connect to or launch Window Server before login. VBoxSVC[1914]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. com.apple.launchd[1] (bar.foo.WikiVirtualBox[1910]): Exited with exit code: 1 When i log into the server via ssh (so no login window opened) i can run: /usr/bin/VBoxHeadless -s wiki and it works. So i don't understand the error above.

  Read the article

• Use launchctl to fire an AppleScript script periodically

  - by Daktari

  I have written an AppleScript that lets me back up a particular file. The script runs fine inside AppleScript Editor: it does what it's supposed to do perfectly. So far so good. Now I'd like to run this script at timed intervals. So I use launchctl & .plist to make this happen. That's where the trouble starts. the script is loaded at set interval by launchctl the AppleScript Editor (when open) brings its window (with that script) to the foreground but no code is executed when AppleScript Editor is not running, nothing seems to be happening at all Any ideas as to why this is not working? -- After editing (as per Daniel Beck's suggestions) my plist now looks like: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>KeepAlive</key> <false/> <key>Label</key> <string>com.opera.autosave</string> <key>ProgramArguments</key> <array> <string>osascript</string> <string>/Users/user_name/Library/Scripts/opera_autosave_bak.scpt</string> </array> <key>StartInterval</key> <integer>30</integer> </dict> </plist> and the AppleScript I'm trying to run: on appIsRunning(appName) tell application "System Events" to (name of processes) contains appName end appIsRunning --only run this script when Opera is running if appIsRunning("Opera") then set base_path to "user_name:Library:Preferences:Opera Preferences:sessions:" set autosave_file to "test.txt" set autosave_file_old to "test_old.txt" set autosave_file_older to "test_older.txt" set autosave_file_oldest to "test_oldest.txt" set autosave_path to base_path & autosave_file set autosave_path_old to base_path & autosave_file_old set autosave_path_older to base_path & autosave_file_older set autosave_path_oldest to base_path & autosave_file_oldest set copied_file to "test copy.txt" set copied_path to base_path & copied_file tell application "Finder" duplicate file autosave_path delete file autosave_path_oldest set name of file autosave_path_older to autosave_file_oldest set name of file autosave_path_old to autosave_file_older set name of file copied_path to autosave_file_old end tell end if

  Read the article

• External hard drive FAT32 to NTFS conversion fails

  - by Pieter

  I'm trying to convert the FAT32 file system of an external hard drive to NTFS. Here's what happened: C:\Windows\system32>chkdsk G: The type of the file system is FAT32. Volume PIETEREXT created 3/19/2008 12:43 Volume Serial Number is 1806-2E30 Windows is verifying files and folders... File and folder verification is complete. Windows has scanned the file system and found no problems. No further action is required. 488,264,768 KB total disk space. 72,192 KB in 1,503 hidden files. 1,281,792 KB in 40,029 folders. 309,235,168 KB in 199,915 files. 177,675,584 KB are available. 32,768 bytes in each allocation unit. 15,258,274 total allocation units on disk. 5,552,362 allocation units available on disk. C:\Windows\system32>cd \ C:\>convert g: /fs:ntfs The type of the file system is FAT32. Enter current volume label for drive G: PIETEREXT Volume PIETEREXT created 3/19/2008 12:43 Volume Serial Number is 1806-2E30 Windows is verifying files and folders... File and folder verification is complete. Windows has scanned the file system and found no problems. No further action is required. 488,264,768 KB total disk space. 72,192 KB in 1,503 hidden files. 1,281,792 KB in 40,029 folders. 309,235,168 KB in 199,915 files. 177,675,584 KB are available. 32,768 bytes in each allocation unit. 15,258,274 total allocation units on disk. 5,552,362 allocation units available on disk. Determining disk space required for file system conversion... Total disk space: 488384001 KB Free space on volume: 177675584 KB Space required for conversion: 975155 KB Converting file system The conversion failed. G: was not converted to NTFS I looked at the TechNet page for my error, but after closing every app the conversion was still failing halfway through. Why does it keep failing? I kept an eye on Task Manager but it didn't look like my system resources were near depletion. I'm using Windows 8.

  Read the article

• Apache strace to hunt down a memory leak

  - by Zipp

  We have a server with a memory issue: the server keeps allocating itself memory and doesn't release it. We're running Apache. I set MaxReqsPerClient to a really low value just so the threads don't hold a lot of memory, but has anyone seen calls like this? Am I wrong in thinking that it's probably Drupal pulling too much data back from the cache in DB? read(52, "h_index\";a:2:{s:6:\"weight\";i:1;s"..., 6171) = 1368 read(52, "\";a:2:{s:6:\"author\";a:3:{s:5:\"la"..., 4803) = 1368 read(52, ":\"description\";s:19:\"Term name t"..., 3435) = 1368 read(52, "abel\";s:4:\"Name\";s:11:\"descripti"..., 2067) = 1368 read(52, "ions\";a:2:{s:4:\"form\";a:3:{s:4:\""..., 16384) = 708 brk(0x2ab554396000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f653000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f753000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f853000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f953000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fa53000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fb53000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fc53000 poll([{fd=52, events=POLLIN|POLLPRI}], 1, 0) = 0 (Timeout) write(52, "d\0\0\0\3SELECT cid, data, created, "..., 104) = 104 read(52, "\1\0\0\1\5E\0\0\2\3def\23drupal_database_nam"..., 16384) = 1368 read(52, ";s:11:\"granularity\";a:5:{s:4:\"ye"..., 34783) = 1368 read(52, ":4:\"date\";}s:9:\"datestamp\";a:9:{"..., 33415) = 1368 read(52, "\";i:0;s:15:\"display_default\";i:0"..., 32047) = 1368 read(52, "e as an integer value.\";s:8:\"set"..., 30679) = 1368 read(52, "label' pairs, i.e. 'Fraction': 0"..., 29311) = 1368 top (the procs just keep growing in memory..): 12845 apache 15 0 581m 246m 37m S 0.0 4.1 0:17.39 httpd 12846 apache 15 0 571m 235m 37m S 0.0 4.0 0:12.13 httpd 12833 apache 15 0 420m 117m 37m S 0.0 2.0 0:06.04 httpd 12851 apache 15 0 412m 113m 37m S 0.0 1.9 0:05.32 httpd 13871 apache 15 0 409m 109m 37m S 0.0 1.8 0:04.90 httpd 12844 apache 15 0 407m 108m 37m S 0.0 1.8 0:04.50 httpd 13870 apache 15 0 407m 108m 37m S 0.3 1.8 0:03.50 httpd 14903 apache 15 0 402m 103m 37m S 0.3 1.7 0:01.29 httpd 14850 apache 15 0 397m 100m 37m S 0.0 1.7 0:02.08 httpd 14907 apache 15 0 390m 93m 36m S 0.0 1.6 0:01.32 httpd 13872 apache 15 0 386m 91m 37m S 0.0 1.5 0:03.13 httpd 12843 apache 15 0 373m 81m 37m S 0.0 1.4 0:02.51 httpd 14901 apache 15 0 370m 75m 33m S 0.0 1.3 0:00.78 httpd 14904 apache 15 0 335m 29m 15m S 0.0 0.5 0:00.26 httpd

  Read the article

• Kernel upgrade CentOS 5.3 mount: could not find filesystem '/dev/root'

  - by matt

  We have a CentOS 5.3 x64 server that by default runs kernel version 2.6.18-164.11.1 and we are attempting to upgrade the box to 2.6.31.12 The drive is LVM +ext3, and the problem I'm having is when I upgrade the kernel and attempt to boot from it, no matter what version of the kernel I use, I get /dev/root not found towards the end of the boot process, and the kernel panics, and than reboots. I'm installing the kernel exactly as it says in this doc. I've tried it "The centOS way " using make rpm and than installing that. I've updated my mkinitrd. The most interesting part of this problem is that it has been so frustrating that I decided to try and clean install centos on an identical machine without LVM, and the result is EXACTLY the same. After upgrading the kernel, I get /dev/root not found. Does anyone know how to fix this, or what information would be relevant to remedy it? I'm open to try anything at this point. One more interesting thing about this problem is that in the new version of the kernel, during boot it complains that dm-mapper is started twice, than panics right after that. I've tried this with other kernel versions, and the result is the same. What am I missing here? If you need any more files, please just ask. Linux cg 2.6.18-164.11.1.el5 #1 SMP Wed Jan 20 07:32:21 EST 2010 x86_64 x86_64 x86_64 GNU/Linux /dev/VolGroup00/LogVol00 / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/VolGroup00/LogVol01 swap swap defaults 0 0 default=1 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.31.12-rt20) //NOT WORKING!!!! root (hd0,0) kernel /vmlinuz-2.6.31.12-rt20 ro root=/dev/VolGroup00/LogVol00 isolcpus=8,9,10,11,12,13,14,15 panic=10 initrd /initrd-2.6.31.12-rt20.img title CentOS (2.6.18-164.11.1.el5) //WORKING!! root (hd0,0) kernel /vmlinuz-2.6.18-164.11.1.el5 ro root=/dev/VolGroup00/LogVol00 isolcpus=8,9,10,11,12,13,14,15 panic=10 initrd /initrd-2.6.18-164.11.1.el5.img

  Read the article

• Converting an EC2 AMI to vmdk image

  - by Reed G. Law

  I've come quite close to getting Amazon Linux to boot inside VirtualBox, thanks to this answer and these websites. A quick overview of the steps I've taken: Launch EC2 instance with Amazon Linux 2011.09 64-bit AMI dd the contents of the EBS volume over ssh to a local image file. Mount the image file as a loopback device and then to a local mount point. Create a new empty disk image file, partition with an offset for a bootloader, and create an ext4 filesystem. Mount the new image's partition and copy everything from the EC2 image. Install grub (using Ubuntu's grub-legacy-ec2 package, not grub2). Convert the image file to vmdk using qemu-img. Create a new VirtualBox VM with the vmdk. Now the VM boots, grub loads, and the kernel is found. But it fails when it tries to mount the root device: dracut Warning: No root device "block:/dev/xvda1" found dracut Warning: Boot has failed. To debug this issue add "rdshell" to the kernel command line. dracut Warning: Signal caught! dracut Warning: Boot has failed. To debug this issue add "rdshell" to the kernel command line. Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init Not tainted 2.6.35.14-107.1.39.amzn1.x86_64 #1 I have tried changing /boot/grub/menu.lst to find the root device by label and UUID, but nothing works. I'm guessing the xen kernel is not compatible with VirtualBox. The reasoning behind all this effort is to make a Vagrant box that is as close to possible as the production enviroment, so deploys can be tested locally. I know it's cheap to do test runs on EC2, but poor connectivity often ruins the experience. Plus it would be really nice to have a virtual machine with the production environment so that co-workers don't have to install everything under the sun just to get up and running with app development. If I were to try running a different kernel, what kernel could I get to be as close as possible to Amazon Linux 2011.09?

  Read the article

• Effecient organization of spare cables and hardware

  - by Jake Wharton

  As many of you also likely do, I have a growing collection of cables, hardware, and spare parts (screws, connectors, etc.). I'm looking to find a good system of organization so that everything isn't a tangled mess, mismatched, and potentially able to be damaged. Since the the three things listed above are all have varying sizes and degrees of delicacy this poises an interesting problem. Presently I have those cheap plastic storage bins you find at Wal-mart for everything. Cables that were once wrapped neatly have become tangled due to numerous "I know I have a cable for this" moments. Hardware is mixed in other bins with odds and ends with no protection from each other. NICs, CPUs, and HDDs are all interacting and likely causing damage. Finally there are stray parts sprinkled amongst these two both in plastic bags and loose. I'm looking to unify this storage into a controlled chaos. Here are my thoughts: Odds and ends are the easiest. Screws, connectors, and small electronic parts lend themselves perfectly to tackle boxes and jewelry boxes. Since these are usually dynamically compartmentalized I can adjust for the contents and label them on the outside or inside of the lid. Cables are easily wrangled with short velcro strips but that doesn't stop them from being all mixed in together. Hardware is the worst offender. Size, shape, and degree of delicacy changes with nearly every piece. I'm willing to sacrifice a bit of organization for a somewhat efficient manner. What are all your thoughts? What is the best type of tackle or jewelry box to use? Most of them are cheap and flimsy. Is there a better alternative? How can I organize cables to know exactly (within reason) where one is? What about associating cables with hardware (Wall adapter to router, etc.)? What kind of storage unit lends itself to all shapes of hardware? Do I need to separate by size or degree of delicacy for better organization?

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Pinning based on origin of a reprepro repository.

  - by Shtééf

  I'm on Ubuntu 10.04, and trying to set up a repository using reprepro. I'd also like the pin everything in that repository to be preferred over anything else, even if packages are older versions. (It will only contain a select set of packages.) However, I cannot seem to get the pinning to work, and believe it has something to do with the repository side of things, rather than the apt configuration on the client. I've taken the following steps to set up my repository Installed a web server (my personal choice here is Cherokee), Created the directory /var/www/apt/, Created the file conf/distributions, like so: Origin: Shteef Label: Shteef Suite: lucid Version: 10.04 Codename: lucid Architectures: i386 amd64 source Components: main Description: My personal repository Ran reprepro export from the /var/www/apt/ directory. Now on any other machine, I can add this (empty) repository over HTTP to my /etc/apt/sources.list, and run apt-get update without any errors: Ign http://archive.lan lucid Release.gpg Ign http://archive.lan/apt/ lucid/main Translation-en_US Get:1 http://archive.lan lucid Release [2,244B] Ign http://archive.lan lucid/main Packages Ign http://archive.lan lucid/main Sources Ign http://archive.lan lucid/main Packages Ign http://archive.lan lucid/main Sources Hit http://archive.lan lucid/main Packages Hit http://archive.lan lucid/main Sources In my case, now I want to use an old version of Asterisk, namely Asterisk 1.4. I rebuilt the asterisk-1:1.4.21.2~dfsg-3ubuntu2.1 package from Ubuntu 9.04 (with some small changes to fix dependencies) and uploaded it to my repository. At this point I can see the new package in aptitude, but it naturally prefers the newer Asterisk 1.6 currently in the Ubuntu 10.04 repositories. To try and fix that, I have created /etc/apt/preferences.d/personal like so: Package: * Pin: release o=Shteef Pin-Priority: 1000 But when I try to install the asterisk package, it will still prefer the 1.6 version over my own 1.4 version. This is what apt-cache policy asterisk shows: asterisk: Installed: (none) Candidate: 1:1.6.2.5-0ubuntu1 Version table: 1:1.6.2.5-0ubuntu1 0 500 http://nl.archive.ubuntu.com/ubuntu/ lucid/universe Packages 1:1.4.21.2~dfsg-3ubuntu2.1shteef1 0 500 http://archive.lan/apt/ lucid/main Packages Clearly, it is not picking up my pin. In fact, when I run just apt-cache policy, I get the following: Package files: 100 /var/lib/dpkg/status release a=now 500 http://archive.lan/apt/ lucid/main Packages origin archive.lan 500 http://security.ubuntu.com/ubuntu/ lucid-security/multiverse Packages release v=10.04,o=Ubuntu,a=lucid-security,n=lucid,l=Ubuntu,c=multiverse origin security.ubuntu.com [...] Unlike Ubuntu's repository, apt doesn't seem to pick up a release-line at all for my own repository. I'm suspecting this is the cause why I can't pin on release o=Shteef in my preferences file. But I can't find any noticable difference between my repository's Release files and Ubuntu's that would cause this. Is there a step I've missed or mistake I've made in setting up my repository?

  Read the article

• Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

  - by alharaka

  UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

  Read the article

• PC freezing when used to print labels

  - by Will

  Hi I have a windows XP machine that is used to print labels from a Zebra label printer. It is connected a member of the domain. I am getting reports that when people try to use the computer it will sometimes be frozen to the point where they have to physically shut the machine down and boot to get it responding. (this happens about once a day). I took a look in Event Viewer and nabbed some of these errors out of it: Event Type: Error Event Source: Userenv Event Category: None Event ID: 1054 Date: 11/12/2010 Time: 9:13:04 AM User: NT AUTHORITY\SYSTEM Computer: FS-LABELMACHINE Description: Windows cannot obtain the domain controller name for your computer network. (A socket operation was attempted to an unreachable host. ). Group Policy processing aborted. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Event Type: Error Event Source: AutoEnrollment Event Category: None Event ID: 15 Date: 11/11/2010 Time: 11:08:25 PM User: N/A Computer: FS-LABELMACHINE Description: Automatic certificate enrollment for local system failed to contact the active directory (0x80072751). A socket operation was attempted to an unreachable host. Enrollment will not be performed. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Hanging application MSACCESS.EXE, version 11.0.8166.0, hang module hungapp, version 0.0.0.0, hang address 0x00000000. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.... SearchIndexer (2420) Unable to write a shadowed header for file C:\Documents and Settings\All Users\Application Data\Microsoft\Search\Data\Applications\Windows\MSS.chk. Error -1032. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Failed auto update retrieval of third-party root list sequence number from: <http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootseq.txt> with error: A connection with the server could not be established For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. I'm not really sure what to make out of this... Thanks for the help in advanced, Will

  Read the article

• mounting ext4 fs with block size of 65536

  - by seaquest

  I am doing some benchmarking on EXT4 performance on Compact Flash media. I have created an ext4 fs with block size of 65536. however I can not mount it on ubuntu-10.10-netbook-i386. (it is already mounting ext4 fs with 4096 bytes of block sizes) According to my readings on ext4 it should allow such big block sized fs. I want to hear your comments. root@ubuntu:~# mkfs.ext4 -b 65536 /dev/sda3 Warning: blocksize 65536 not usable on most systems. mke2fs 1.41.12 (17-May-2010) mkfs.ext4: 65536-byte blocks too big for system (max 4096) Proceed anyway? (y,n) y Warning: 65536-byte blocks too big for system (max 4096), forced to continue Filesystem label= OS type: Linux Block size=65536 (log=6) Fragment size=65536 (log=6) Stride=0 blocks, Stripe width=0 blocks 19968 inodes, 19830 blocks 991 blocks (5.00%) reserved for the super user First data block=0 1 block group 65528 blocks per group, 65528 fragments per group 19968 inodes per group Writing inode tables: done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 37 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. root@ubuntu:~# tune2fs -l /dev/sda3 tune2fs 1.41.12 (17-May-2010) Filesystem volume name: <none> Last mounted on: <not available> Filesystem UUID: 4cf3f507-e7b4-463c-be11-5b408097099b Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 19968 Block count: 19830 Reserved block count: 991 Free blocks: 18720 Free inodes: 19957 First block: 0 Block size: 65536 Fragment size: 65536 Blocks per group: 65528 Fragments per group: 65528 Inodes per group: 19968 Inode blocks per group: 78 Flex block group size: 16 Filesystem created: Sat Feb 5 14:39:55 2011 Last mount time: n/a Last write time: Sat Feb 5 14:40:02 2011 Mount count: 0 Maximum mount count: 37 Last checked: Sat Feb 5 14:39:55 2011 Check interval: 15552000 (6 months) Next check after: Thu Aug 4 14:39:55 2011 Lifetime writes: 70 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: afb5b570-9d47-4786-bad2-4aacb3b73516 Journal backup: inode blocks root@ubuntu:~# mount -t ext4 /dev/sda3 /mnt/ mount: wrong fs type, bad option, bad superblock on /dev/sda3, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• Starting php-cgi at boot on mac os x 10.6.8

  - by nikhil

  I'm new to mac os, I have installed and configured nginx with php-fastcgi. I need to run this command in a terminal and keep that terminal open to access php files from my browser. php-cgi -b 127.0.0.1:9000 -q Here's the plist that I wrote by looking up sources on the internet <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Debug</key> <false/> <key>EnvironmentVariables</key> <dict> <key>PHP_FCGI_CHILDREN</key> <string>2</string> <key>PHP_FCGI_MAX_REQUESTS</key> <string>1000</string> </dict> <key>RunAtLoad</key> <true/> <key>KeepAlive</key> <true/> <key>UserName</key> <string>nikhil</string> <key>Label</key> <string>php-fastcgi</string> <key>ProgramArguments</key> <array> <string>/usr/bin/php-cgi</string> <string>-b 127.0.0.1:9000</string> <string>-q</string> </array> </dict> </plist> I'm loading it using launchctl load -w ~/Library/LaunchAgents/php-fastcgi.plist without any success, can anyone tell me how this can be done.

  Read the article

• Why is mount -a not mounting fuse drive properly when executed remotely (via Fabric)?

  - by Jim D

  This is a weird bug and I'm not sure where it's coming from. Here's a quick run down of what I'm doing. I'm trying to mount a FUSE drive to an Amazon EC2 instance running Ubuntu 10.10 using s3fs (FUSE over Amazon). s3fs is compiled from source according to the instructions etc. I've also added an entry to /etc/fstab so that the drive mounts on boot. Here's what /etc/fstab looks like: # /etc/fstab: static file system information. # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 LABEL=uec-rootfs / ext4 defaults 0 0 /dev/sda2 /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 /dev/sda3 none swap sw,comment=cloudconfig 0 0 s3fs#mybucket /mnt/s3/mybucket fuse default_acl=public-read,use_cache=/tmp,allow_other 0 0 So the good news is that this works fine. On reboot the connection mounts correctly. I can also do: $ sudo umount /mnt/s3/mybucket $ sudo mount -a $ mountpoint /mnt/s3/mybucket /mnt/s3/mybucket is a mountpoint Great, right? Well here's the problem. I'm using Fabric to automate the process of building and managing this instance. I noticed I was getting this error message when using Fabric to build s3fs and set up the mount process: mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected I isolated it down the the problem and built a fabric task that reproduces the problem: def remount_s3fs(): sudo("mount -a") Which does: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: mount -a [And yes, I was sure to unmount it before running this task.] When I check the mount using mountpoint I get: $ mountpoint /mnt/s3/mybucket mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected Done. But if I run sudo mount -a at the command line, it works. Hrm. Here is that fab task output again, this time in full debug mode: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a" Again, I get that transport endpoint not connected error. I've also tried copying and pasting the exact command run into my ssh session (i.e. sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a") and it works fine. So...that's my problem. Any ideas?

  Read the article

• FTP Upload works from local command line / remote GUI client but not from PHP script

  - by MrOodles

  I originally posted this question at StackOverflow, but I'm beginning to think it's more of a server question. I have installed ProFTPd on an EC2 instance running Ubuntu 10.10. I have managed my proftpd.conf file as well as my server permissions to be able to connect and upload/move files using FTP both remotely using Filezilla, and on the server itself when connecting to 127.0.0.1. The problem I'm running into is when I try to upload/install a file using Joomla's interface. I give Joomla the same login information that I give to Filezilla, and the connection is made in the same fashion. The ftp.log file actually shows that Joomla is able to login to the server: localhost UNKNOWN nobody [17/Jan/2011:14:09:17 +0000] "USER ftpuser" 331 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "PASS (hidden)" 230 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "PASV" 227 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "TYPE I" 200 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "STOR /directory/store/location/file.zip" 550 - But it fails when attempting the STOR command. I have traced the problem in the Joomla code to the PHP FTP module. The code (with my trace statements added): if (@ftp_put($this->_conn, $remote, $local, $mode) === false) { echo "\n FTP PUT failed."; echo "\n Remote: $remote ; Local: $local ; Mode: $mode - Either ASCII: ".FTP_ASCII." or Binary: ".FTP_BINARY; echo "\n The user: ".exec("whoami"); JError::raiseWarning('35', 'JFTP::store: Bad response' ); return false; } Trace ouputs: FTP PUT failed. Remote: /directory/store/location/file.zip ; Local: /tmp/phpwuccp4 ; Mode: 2 - Either ASCII: 1 or Binary: 2 The user: www-data And in case you were curious, here is an example of the FTP log when using Filezilla: my_client_ip UNKNOWN nobody [17/Jan/2011:16:45:55 +0000] "USER ftpuser" 331 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PASS (hidden)" 230 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "OPTS UTF8 ON" - - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PWD" 257 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "TYPE I" 200 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "MLSD" 226 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "CWD location" 250 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "PWD" 257 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "PASV" 227 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:07 +0000] "MLSD" 226 3757 my_client_ip UNKNOWN nobody [17/Jan/2011:16:46:37 +0000] "USER ftpuser" 331 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PASS (hidden)" 230 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "OPTS UTF8 ON" - - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "CWD /location" 250 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PWD" 257 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "TYPE I" 200 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "STOR file.zip" 226 125317 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "MLSD" 226 497

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• How can I fix Problems with interlaced video jerking/flicking when playedback on DVD players? (Mixin

  - by Simon P Stevens

  I'm trying to make a DVD and the final DVD jerks when played on standalone DVD players. It seems to play fine on PCs. I think the problem may be to do with interlacing settings when rendering the final output, but I'll outline the whole editing process I have followed in case I've made a mistake somewhere else. Most of the footage comes from a sony handy cam (one of those mini DVD ones) so isn't great quality. It was set to "high quality" (haha) and 16:9 aspect ratio when it was recorded. I copy the files directly from the mini DVDs onto the hard drive and import them into Cinelerra. In Cinelerra I set the format to 25fps, 720x576, RGBA-8bit, 16:9, interlaced bottom fields first. When I've finished the editing, I add a Fields to frames effect (set to bottom first) to each video track. I render to audio and video separately: Audio: AC3, 128kbps Video: YUV4MPEG steam, video pipe settings: ffmpeg -f yuv4mpegpipe -i - -y -target dvd -flags +ilme+ildct mpeg2video % Cinelerra often crashes during the rendering, so I set it to generate a new video file at each label, and combine them using cat when I've got a sucesful render of each one. Once I've combined them, I use mencoder to re-index them: mencoder -forceidx -oac copy -ovc copy merged.m2v -o mergedReIndexed.m2v I combine the audio and video files using ffmpeg: ffmpeg -i AudioFile.ac3 -i VideoFile.m2v -target dvd -flags +ilme+ildct FinalMovie.mpg Then I build the menus with spumux and I create the DVD file system with dvdauthor, and finally I write it do a dvd-r like this: nice -n -20 growisofs -dvd-compat -speed=2 -Z /dev/dvd -dvd-video -V VIDEO ./ && eject /dev/dvd Originally, when I did it the DVD flickered badly, so as suggested in a guide I added the fields to frames effect in cinelerra. Now it doesn't "flicker", but has become "jerky" when there is lots of motion, particularly when the camera is moving, so the whole background moves. This is what I've tried so far: Removed "mpeg2video" from cinelerra video render pipe. Removed +ilme from render pipe. Removed +ildct from render pipe. Removed +ilme from render audio/video rejoin command. Removed +ildct from render audio/video rejoin command. Added -alt to render pipe. Added -alt to render audio/video rejoin command. Tried with and without the frames to fields effect in Cinelerra. and various combinations of the above. I've also tried this: change the Cinelerra fps to 50, use fields to frames (instead of frames to fields), render to an intermediate QTforlinux jpeg video stream, re-importing that back into Cinelerra, adding a frames to fields effect and then rendering that output as normal (@25fps), and I still have the same problem. Has anyone experienced this "jerking" playback before? Can anyone give any suggestions on how to fix it? (Like I say, it plays back fine on a PC, but not on any of the standalone players I've tried)

  Read the article

• can't access nginx server from IP

  - by EquinoX

  So 2 days ago I can see that page where it saya "Welcome to nginx", however as of now when I tried to access it, it says 404 page not found... Why is this? Inside my sites-enabled folder I have a file named default and it has the following: # You may add here your # server { # ... # } # statements for each of your virtual hosts server { listen 80; server_name 127.0.0.1; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; deny all; } location /images { root /usr/share; autoindex on; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /var/www/nginx-default; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { #proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/nginx-default$fastcgi_script_name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { #listen 8000; #listen somename:8080; #server_name somename alias another.alias; #location / { #root html; #index index.html index.htm; #} #} # HTTPS server # #server { #listen 443; #server_name localhost; #ssl on; #ssl_certificate cert.pem; #ssl_certificate_key cert.key; #ssl_session_timeout 5m; #ssl_protocols SSLv2 SSLv3 TLSv1; #ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; #ssl_prefer_server_ciphers on; #location / { #root html; #index index.html index.htm; #} #} Here's my nginx.conf file: user www-data; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } # mail { # # See sample authentication script at: # # http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } # } What am I doing wrong here? I have other virtual host setup in the sites-enabled as well... UPDATE: The server_name directives are: -admin.api.frapi -api.frapi -default -example.com -php.example.com

  Read the article

• When upgrading from Vista to Windows 7 on a DELL laptop, how do I know which drivers to reinstall an

  - by msorens

  According to Dell's upgrade page for Vista to Windows 7, after using the upgrade assistant the final step is to install drivers. They refer to this page for the order of driver installation, listing 9 items. From there I go to the Dell Drivers and Downloads page, enter my system tag, and get a list of the downloads available for my specific box. That page, by the way, has a link to driver install instructions that lists 10 rather than 9 items. Going to Drivers Help in the side panel and clicking on "In what order should drivers be installed?" shows yet a third list, this one containing 13 items. Not surprisingly, the order of these 3 lists of drivers are not quite the same for the common items! Furthermore, of the 26 files Dell's site recommends for my machine, there are several not shown on any of the 3 lists! I can make determinations for some of these: 6 of them are "applications" so I know which of those I want and that they could probably be safely installed after all drivers. BIOS: I would think this should be unaffected by an OS upgrade so could be skipped. Two tools in the diagnostics category: could probably be done after all drivers. That leaves just a CD/DVD driver and a webcam driver unaccounted for. So my two related questions are these: How critical is the driver installation order and which one do I follow? (Keep in mind this is for an upgrade, not a fresh install.) Where in the order do I insert the CD/DVD and the webcam drivers (if needed) ? Dell's driver download page provides (in theory) the list of all downloads relevant to my specific machine, via the service tag. But do I actually need to reinstall all of them? some? none? How does one determine this? They do label each with Recommended or Optional, so do I need to reinstall all the recommended ones? (Part of the reason for my perplexed frown is that I wonder why I would need to reinstall a CD/DVD driver since I would already be using the drive to install the OS!)

  Read the article

• ZFS Recover from Faulted Pool State

  - by nickv2002

  I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can tell). I was able to get another machine from a friend to rebuild the system, but in the process of moving my drives over I had to swap their cables around a bunch until I got the right configuration where the remaining 5 good disks were seen as online. This process seems to have generated some checksum errors for the pool/raidz. I have the 5 remaining drives set up now and a good drive installed and ready to take the place of the drive that died. However, since my pool state is FAULTED I'm unable to do the replacement. root@zfs:~# zpool replace tank 1298243857915644462 /dev/sdb cannot open 'tank': pool is unavailable Is there any way to recover from this error? I would think that having 5 of the 6 drives online would be enough to rebuild the right data, but that doesn't seem to be enough now. Here's the status log of my pool: root@zfs:~# zpool status tank pool: tank state: FAULTED status: One or more devices could not be used because the label is missing or invalid. There are insufficient replicas for the pool to continue functioning. action: Destroy and re-create the pool from a backup source. see: http://zfsonlinux.org/msg/ZFS-8000-5E scan: none requested config: NAME STATE READ WRITE CKSUM tank FAULTED 0 0 1 corrupted data raidz1-0 ONLINE 0 0 8 sdd ONLINE 0 0 0 sdf ONLINE 0 0 0 sdh ONLINE 0 0 0 1298243857915644462 UNAVAIL 0 0 0 was /dev/sdb1 sde ONLINE 0 0 0 sdg ONLINE 0 0 0 Update (10/31): I tried to export and re-import the array a few times over the past week and wasn't successful. First I tried: zpool import -f -R /tank -N -o readonly=on -F tank That produced this error immediately: cannot import 'tank': I/O error Destroy and re-create the pool from a backup source. I added the '-X' option to the above command to try to make it check the transaction log. I let that run for about 48 hours before giving up because it had completely locked up my machine (I was unable to log in locally or via the network). Now I'm trying a simple zpool import tank command and that seems to run for a while with no output. I'll leave it running overnight to see if it outputs anything.

  Read the article

• Is there a Math.atan2 substitute for j2ME? Blackberry development

  - by Kai

  I have a wide variety of locations stored in my persistent object that contain latitudes and longitudes in double(43.7389, 7.42577) format. I need to be able to grab the user's latitude and longitude and select all items within, say 1 mile. Walking distance. I have done this in PHP so I snagged my PHP code and transferred it to Java, where everything plugged in fine until I figured out J2ME doesn't support atan2(double, double). So, after some searching, I find a small snippet of code that is supposed to be a substitute for atan2. Here is the code: public double atan2(double y, double x) { double coeff_1 = Math.PI / 4d; double coeff_2 = 3d * coeff_1; double abs_y = Math.abs(y)+ 1e-10f; double r, angle; if (x >= 0d) { r = (x - abs_y) / (x + abs_y); angle = coeff_1; } else { r = (x + abs_y) / (abs_y - x); angle = coeff_2; } angle += (0.1963f * r * r - 0.9817f) * r; return y < 0.0f ? -angle : angle; } I am getting odd results from this. My min and max latitude and longitudes are coming back as incredibly low numbers that can't possibly be right. Like 0.003785746 when I am expecting something closer to the original lat and long values (43.7389, 7.42577). Since I am no master of advanced math, I don't really know what to look for here. Perhaps someone else may have an answer. Here is my complete code: package store_finder; import java.util.Vector; import javax.microedition.location.Criteria; import javax.microedition.location.Location; import javax.microedition.location.LocationException; import javax.microedition.location.LocationListener; import javax.microedition.location.LocationProvider; import javax.microedition.location.QualifiedCoordinates; import net.rim.blackberry.api.invoke.Invoke; import net.rim.blackberry.api.invoke.MapsArguments; import net.rim.device.api.system.Bitmap; import net.rim.device.api.system.Display; import net.rim.device.api.ui.Color; import net.rim.device.api.ui.Field; import net.rim.device.api.ui.Graphics; import net.rim.device.api.ui.Manager; import net.rim.device.api.ui.component.BitmapField; import net.rim.device.api.ui.component.RichTextField; import net.rim.device.api.ui.component.SeparatorField; import net.rim.device.api.ui.container.HorizontalFieldManager; import net.rim.device.api.ui.container.MainScreen; import net.rim.device.api.ui.container.VerticalFieldManager; public class nearBy extends MainScreen { private HorizontalFieldManager _top; private VerticalFieldManager _middle; private int horizontalOffset; private final static long animationTime = 300; private long animationStart = 0; private double latitude = 43.7389; private double longitude = 7.42577; private int _interval = -1; private double max_lat; private double min_lat; private double max_lon; private double min_lon; private double latitude_in_degrees; private double longitude_in_degrees; public nearBy() { super(); horizontalOffset = Display.getWidth(); _top = new HorizontalFieldManager(Manager.USE_ALL_WIDTH | Field.FIELD_HCENTER) { public void paint(Graphics gr) { Bitmap bg = Bitmap.getBitmapResource("bg.png"); gr.drawBitmap(0, 0, Display.getWidth(), Display.getHeight(), bg, 0, 0); subpaint(gr); } }; _middle = new VerticalFieldManager() { public void paint(Graphics graphics) { graphics.setBackgroundColor(0xFFFFFF); graphics.setColor(Color.BLACK); graphics.clear(); super.paint(graphics); } protected void sublayout(int maxWidth, int maxHeight) { int displayWidth = Display.getWidth(); int displayHeight = Display.getHeight(); super.sublayout( displayWidth, displayHeight); setExtent( displayWidth, displayHeight); } }; add(_top); add(_middle); Bitmap lol = Bitmap.getBitmapResource("logo.png"); BitmapField lolfield = new BitmapField(lol); _top.add(lolfield); Criteria cr= new Criteria(); cr.setCostAllowed(true); cr.setPreferredResponseTime(60); cr.setHorizontalAccuracy(5000); cr.setVerticalAccuracy(5000); cr.setAltitudeRequired(true); cr.isSpeedAndCourseRequired(); cr.isAddressInfoRequired(); try{ LocationProvider lp = LocationProvider.getInstance(cr); if( lp!=null ){ lp.setLocationListener(new LocationListenerImpl(), _interval, 1, 1); } } catch(LocationException le) { add(new RichTextField("Location exception "+le)); } //_middle.add(new RichTextField("this is a map " + Double.toString(latitude) + " " + Double.toString(longitude))); int lat = (int) (latitude * 100000); int lon = (int) (longitude * 100000); String document = "<location-document>" + "<location lon='" + lon + "' lat='" + lat + "' label='You are here' description='You' zoom='0' />" + "<location lon='742733' lat='4373930' label='Hotel de Paris' description='Hotel de Paris' address='Palace du Casino' postalCode='98000' phone='37798063000' zoom='0' />" + "</location-document>"; // Invoke.invokeApplication(Invoke.APP_TYPE_MAPS, new MapsArguments( MapsArguments.ARG_LOCATION_DOCUMENT, document)); _middle.add(new SeparatorField()); surroundingVenues(); _middle.add(new RichTextField("max lat: " + max_lat)); _middle.add(new RichTextField("min lat: " + min_lat)); _middle.add(new RichTextField("max lon: " + max_lon)); _middle.add(new RichTextField("min lon: " + min_lon)); } private void surroundingVenues() { double point_1_latitude_in_degrees = latitude; double point_1_longitude_in_degrees= longitude; // diagonal distance + error margin double distance_in_miles = (5 * 1.90359441) + 10; getCords (point_1_latitude_in_degrees, point_1_longitude_in_degrees, distance_in_miles, 45); double lat_limit_1 = latitude_in_degrees; double lon_limit_1 = longitude_in_degrees; getCords (point_1_latitude_in_degrees, point_1_longitude_in_degrees, distance_in_miles, 135); double lat_limit_2 = latitude_in_degrees; double lon_limit_2 = longitude_in_degrees; getCords (point_1_latitude_in_degrees, point_1_longitude_in_degrees, distance_in_miles, -135); double lat_limit_3 = latitude_in_degrees; double lon_limit_3 = longitude_in_degrees; getCords (point_1_latitude_in_degrees, point_1_longitude_in_degrees, distance_in_miles, -45); double lat_limit_4 = latitude_in_degrees; double lon_limit_4 = longitude_in_degrees; double mx1 = Math.max(lat_limit_1, lat_limit_2); double mx2 = Math.max(lat_limit_3, lat_limit_4); max_lat = Math.max(mx1, mx2); double mm1 = Math.min(lat_limit_1, lat_limit_2); double mm2 = Math.min(lat_limit_3, lat_limit_4); min_lat = Math.max(mm1, mm2); double mlon1 = Math.max(lon_limit_1, lon_limit_2); double mlon2 = Math.max(lon_limit_3, lon_limit_4); max_lon = Math.max(mlon1, mlon2); double minl1 = Math.min(lon_limit_1, lon_limit_2); double minl2 = Math.min(lon_limit_3, lon_limit_4); min_lon = Math.max(minl1, minl2); //$qry = "SELECT DISTINCT zip.zipcode, zip.latitude, zip.longitude, sg_stores.* FROM zip JOIN store_finder AS sg_stores ON sg_stores.zip=zip.zipcode WHERE zip.latitude<=$lat_limit_max AND zip.latitude>=$lat_limit_min AND zip.longitude<=$lon_limit_max AND zip.longitude>=$lon_limit_min"; } private void getCords(double point_1_latitude, double point_1_longitude, double distance, int degs) { double m_EquatorialRadiusInMeters = 6366564.86; double m_Flattening=0; double distance_in_meters = distance * 1609.344 ; double direction_in_radians = Math.toRadians( degs ); double eps = 0.000000000000005; double r = 1.0 - m_Flattening; double point_1_latitude_in_radians = Math.toRadians( point_1_latitude ); double point_1_longitude_in_radians = Math.toRadians( point_1_longitude ); double tangent_u = (r * Math.sin( point_1_latitude_in_radians ) ) / Math.cos( point_1_latitude_in_radians ); double sine_of_direction = Math.sin( direction_in_radians ); double cosine_of_direction = Math.cos( direction_in_radians ); double heading_from_point_2_to_point_1_in_radians = 0.0; if ( cosine_of_direction != 0.0 ) { heading_from_point_2_to_point_1_in_radians = atan2( tangent_u, cosine_of_direction ) * 2.0; } double cu = 1.0 / Math.sqrt( ( tangent_u * tangent_u ) + 1.0 ); double su = tangent_u * cu; double sa = cu * sine_of_direction; double c2a = ( (-sa) * sa ) + 1.0; double x= Math.sqrt( ( ( ( 1.0 /r /r ) - 1.0 ) * c2a ) + 1.0 ) + 1.0; x= (x- 2.0 ) / x; double c= 1.0 - x; c= ( ( (x * x) / 4.0 ) + 1.0 ) / c; double d= ( ( 0.375 * (x * x) ) -1.0 ) * x; tangent_u = distance_in_meters /r / m_EquatorialRadiusInMeters /c; double y= tangent_u; boolean exit_loop = false; double cosine_of_y = 0.0; double cz = 0.0; double e = 0.0; double term_1 = 0.0; double term_2 = 0.0; double term_3 = 0.0; double sine_of_y = 0.0; while( exit_loop != true ) { sine_of_y = Math.sin(y); cosine_of_y = Math.cos(y); cz = Math.cos( heading_from_point_2_to_point_1_in_radians + y); e = (cz * cz * 2.0 ) - 1.0; c = y; x = e * cosine_of_y; y = (e + e) - 1.0; term_1 = ( sine_of_y * sine_of_y * 4.0 ) - 3.0; term_2 = ( ( term_1 * y * cz * d) / 6.0 ) + x; term_3 = ( ( term_2 * d) / 4.0 ) -cz; y= ( term_3 * sine_of_y * d) + tangent_u; if ( Math.abs(y - c) > eps ) { exit_loop = false; } else { exit_loop = true; } } heading_from_point_2_to_point_1_in_radians = ( cu * cosine_of_y * cosine_of_direction ) - ( su * sine_of_y ); c = r * Math.sqrt( ( sa * sa ) + ( heading_from_point_2_to_point_1_in_radians * heading_from_point_2_to_point_1_in_radians ) ); d = ( su * cosine_of_y ) + ( cu * sine_of_y * cosine_of_direction ); double point_2_latitude_in_radians = atan2(d, c); c = ( cu * cosine_of_y ) - ( su * sine_of_y * cosine_of_direction ); x = atan2( sine_of_y * sine_of_direction, c); c = ( ( ( ( ( -3.0 * c2a ) + 4.0 ) * m_Flattening ) + 4.0 ) * c2a * m_Flattening ) / 16.0; d = ( ( ( (e * cosine_of_y * c) + cz ) * sine_of_y * c) + y) * sa; double point_2_longitude_in_radians = ( point_1_longitude_in_radians + x) - ( ( 1.0 - c) * d * m_Flattening ); heading_from_point_2_to_point_1_in_radians = atan2( sa, heading_from_point_2_to_point_1_in_radians ) + Math.PI; latitude_in_degrees = Math.toRadians( point_2_latitude_in_radians ); longitude_in_degrees = Math.toRadians( point_2_longitude_in_radians ); } public double atan2(double y, double x) { double coeff_1 = Math.PI / 4d; double coeff_2 = 3d * coeff_1; double abs_y = Math.abs(y)+ 1e-10f; double r, angle; if (x >= 0d) { r = (x - abs_y) / (x + abs_y); angle = coeff_1; } else { r = (x + abs_y) / (abs_y - x); angle = coeff_2; } angle += (0.1963f * r * r - 0.9817f) * r; return y < 0.0f ? -angle : angle; } private Vector fetchVenues(double max_lat, double min_lat, double max_lon, double min_lon) { return new Vector(); } private class LocationListenerImpl implements LocationListener { public void locationUpdated(LocationProvider provider, Location location) { if(location.isValid()) { nearBy.this.longitude = location.getQualifiedCoordinates().getLongitude(); nearBy.this.latitude = location.getQualifiedCoordinates().getLatitude(); //double altitude = location.getQualifiedCoordinates().getAltitude(); //float speed = location.getSpeed(); } } public void providerStateChanged(LocationProvider provider, int newState) { // MUST implement this. Should probably do something useful with it as well. } } } please excuse the mess. I have the user lat long hard coded since I do not have GPS functional yet. You can see the SQL query commented out to know how I plan on using the min and max lat and long values. Any help is appreciated. Thanks

  Read the article

< Previous Page | 283 284 285 286 287 288 289 290 291 292 293 294  | Next Page >