Search Results

Search found 10388 results on 416 pages for 'hardware selection'.

Page 288/416 | < Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >

• Can a RAID 4 disk setup crash if only 1 hard disk fails?

  - by Steve Rodrigue

  I am a web developer. I have not much experience in hardware. For this reason, I use managed servers. This morning, one of the drives in our setup failed. However, the full site went down. I asked my web host what happened and he replied that the hard disk failed in such a way that the RAID controller couldn't work properly. The array was set up as RAID 4. Do you guys ever seen that before? Is it possible? Thanks for any help on this guys. I need to know if my web host is honest with me.

  Read the article

• Different versions of 2.5" drives? Unscreawing Intel 320 for slimmer drive to fit newer thinkpads?

  - by hhh

  My x60s laptops come with about 1-2mm heigher 2.5" HDD than newer x220 models. This is totally stupid when one would like to reuse the old drive in the newer laptops. I bought newer 2.5" 320 Intel SSDs and they seem to have such 1-2mm gap to unscrew but I am unsure whether it is meant for opening. Could someone instruct what to do here? Look the manufacturer has started changing the old good 2.5" drives into slightly different versions, now it means slow compability issues to fix or totally new 2.5" drives. Ideas how to proceed? Unscrewing newer 320 drives or are some other versions of 2.5" drives meant for x220? Does there exist some sort of racks to get drives working between different comps? Perhaps booting from laplink is currently the easiest solution to get things working when changing harddrives between comps? Perhaps related http://www.zdnet.com/blog/hardware/seagate-announced-super-slim-25in-momentus-thin-hard-drive/6439

  Read the article

• Monitor has yellow tint when used with the graphics card

  - by artknish

  I have an nVIDIA graphics card when used produces an yellow tint on my monitor's display. I tried with another monitor and it had the same issue. I then switched back to my motherboard's inbuilt graphics output (not sure what the technical term is), and the display seems fine, except I can't get the optimal resolution of 1440x900 to work. So is my graphics card's life over? Or can I get it repaired? Any self remedies without calling a hardware guy? Should I try with a DVI cable? I've been using the VGA cable from my graphics card to the monitor so far. Thanks for your suggestions!

  Read the article

• Exchange Failover Solution

  - by Dan

  I've been given the task to come up with an exchange solution that will support 200 users total throughout 4 states. 1GB per user. It needs to have a failover solution,The failover must reside in another location. There is an mpls that connects the locations. I am hoping to get recomendations on hardware, software setups. I recently worked with some big name reps and they steered me in the wrong direction and now I'm a few days away from my proposal date with bogus quotes and scrambling for a solution. I used to manage a standalone 2003 exchange server for years and am at a loss now with figuring out a clustering/failover...Any help would be greatly appreciated. thank you

  Read the article

• How does a winkydink Teradici offer high res, full FPS, 3D rendering on ESXi 5 VDIs for AutoCAD/SolidWorks/1080p YouTube applications?

  - by BlueToast

  How does such a small Teradici card ![enter image description here][1] offer high resolution, full FPS 3D graphics (1:38) http://www.youtube.com/watch?v=eXA4QMmfY5Y&feature=player_detailpage#t=97s for ESXi 5.0/5.1 VDI environments? We're shooting for an AutoCAD/SolidWorks/YouTube 1080p capable environment. I can't see how such a small and low profile card could possibly have the horsepower to handle such GPU computations for a big environment like that. We're going to have up to 64 VDIs per server, and are a 500-1000 employee count sized company. Someone enlighten me please! Determining which route to go (between RemoteFX and VMware View/PCoIP) and the hardware (NVIDIA 4GB non-Quadro/Tesla GPUs vs Teradici card). Servers have three 4x, three 8x, and one 16x PCI-E lane. Two of the 8x lanes will be occupied by SAS RAID cards.

  Read the article

• Windows XP 32-bit + RocketRaid 622 + 4 x 3TB = not quite a RAID setup

  - by gmoney

  I'm looking to make a 6TB RAID 10 array from my new pile of drives under Windows XP 32-bit, however they are only for auxiliary storage. After adding all the drives to an array, and initializing them XP sees only a fraction of the storage, 2TB. I'm assuming this has to do with MBR vs GPT. Is making a series of 2TB volumes and then spanning my only solution? Most questions online have to do with booting from this setup, but I'm just using them as extra storage. Hardware: 4 x 3TB Hitachi Deskstars + RocketRaid 622 + Sans Digital TR8M TowerRAID. The array is connected via eSATA.

  Read the article

• Is it possible to re-create the Windows 8.1 install image after the upgrade

  - by rossmcm

  I have downloaded and installed the Windows 8.1 upgrade from the Windows store. The hardware was a 64-bit Toshiba P50 laptop. I need to upgrade a second P50 and wish to do so without another 3.6Gb download (I tried the instructions here but never got the chance to create the installation media, nor was I asked for a product key). I saw mention on superuser of creating USB rescue media after installation and using that to clone the upgrade onto another machine. Is this likely to be a viable option?

  Read the article

• System stuttering caused by hard drive

  - by LukLed

  My system keeps freezing for about 1-2 second every time I try to do something. For example, when I enter URL in browser, it freezes and starts working after few seconds. It is probably related to hard drive. I installed HD tune and when benchmark is in progress, causing constant disk use, everything works fine in background, there are no lags. What can be the reason of this issue? My hardware is Acer Aspire 7740G-6969 running on Windows 7.

  Read the article

• How to put fear of God (law) into Wi-Fi hacking neighbors [closed]

  - by Shakehar

  I live in an apartment and some new guys have apparently moved into one of the apartments. They have been shamelessly hacking into my WiFi. Mine was initially a WEP encrypted network and out of laziness I just limited and reserved the IPS on my router for the people in my house. Yesterday I had to free up an IP for a guest in my house but before he could join the network these guys connected in. I have changed my encryption to WPA2 and hope they dont have the hardware/patience required to hack into it, but there are many wi-fi networks in my apartment most of which are secured using WEP. I don't really want to call the police on them. Is there any way to deter them from misusing other people's wi-fi ? I have gone through I think someone else has access to my wireless network. What next? but I have already taken the steps mentioned there.

  Read the article

• 'hijacking' gui and mapping certain controls to certain functions. VNC. TouchOSC

  - by Nick

  I need a VNC LIKE application which rather than sharing the screen, can take control of a specific application and then share that functionality across a network to multiple clients. Obviously, VNC requires use of the mouse and therefore only one user can do something at one time, this is NOT what I am after. I am after something that can hijack the graphic user interface, map certain controls, and then display them in another piece of software (perhaps like TOUCHOSC) The software I would like to map and share is called YAMAHA STUDIO MANAGER and is used to control certain Yamaha audio hardware, and in my case a Yamaha LS9 and M7CL mixing console. Its free.

  Read the article

• SNMP - So I have a MIB. Now What?

  - by senfo

  I can't seem to get my head wrapped around the purpose of a MIB. I have a collection of ~20 MIB files that were supplied to me by the vendor, but what do I do with them? I also have a few OID's that were supplied by the vendor that don't seem to be valid. When I issue an "snmpget -v1 -c public 192.168.0.123 .1.4.6.3.2.6.2" (assume that's a valid OID), I get an error indicating the variable is unknown. Does this sound like a hardware configuration problem? Do I need to "load" (for lack of better words) the MIB into the device? Unfortunately, the vendor has been completely unresponsive with returning emails to my questions, so any help would be greatly appreciated.

  Read the article

• Any recommendations on a NAS for a home-super-user?

  - by marc_s

  Can anyone recommend a good NAS for use in a home-server environment? I would request at least 2, preferably 4 disks, and I am most interested in good to excellent throughput for file-server and backup purposes - don't need any of the fancy media-streaming or -sharing features, that's not of interest to me. For a 4 or more disk solution, support for the various RAID levels (0, 1, 1+0, 5) would be a plus - especially if supported in hardware (rather than just a software emulation). I just need a place to put my collection of data, ISO images, and so forth - and since several external disks (self-built and off-the-shelf) have failed so far, I'm looking into a more reliable solution. Marc

  Read the article

• How to switch off the monitor when mouse reaches the edge of the screen?

  - by evgeny9

  I have 2 computers at home (Windows XP and Windows 7), but one monitor for both of them. They are connected to this monitor using different interfaces: DVI and VGA. I'm also using one keyboard and one mouse to control both PCs with the help of Synergy or Input Director. But I still need to manually switch between monitor interfaces. I wonder, if there's some way (software) that will switch this interfaces (turn off the monitor), when reach the edge of the screen with the mouse. Until now I found several answers, which help to avoid pressing hardware buttons, but still can not do the job automatically based on mouse pointer coordinates. Thank you.

  Read the article

• RAID setup for maximizing data retention and read speed

  - by cat pants

  My goals are simple: maximize data retention safety, and maximize read speeds. My first instinct is to do a a three drive software RAID 1. I have only used fakeraid RAID 1 in the past and it was terrible (would have led to data loss actually if it weren't for backups) Would you say software raid 1 or a cheap actual hardware raid card? OS will be linux. Could I start with a two drive raid 1 and add a third drive on the fly? Can I hot swap? Can I pull one of the drives and throw it into a new machine and be able to read all the data? I do not want a situation where I have a raid card fail and have to try and find the same chipset in order to read my data (which i am assuming can happen) Please clarify any points on which it sounds like I have no idea what I am talking about, as I am admittedly inexperienced here. (My hardest lesson was fakeraid lol) Thanks!

  Read the article

• Cannot get Virtual PC to install on my machine

  - by Brandon

  I'm not sure what I'm doing wrong. I ran the tool to check that hardware virtualization is enabled, and it is (i7-2600). I ran the proper version of the Virtual PC download (Windows 7 Professional x64) and I can see the Windows Virtual PC (KB958559) update in my installed updates list. The .msu file runs fine without errors, but even after multiple reboots I can't actually find a trace of Virtual PC anywhere. There is nothing in program files, the start menu, or system32. Am I missing a step?

  Read the article

• Installing Windows on multiple computers

  - by Rob

  At our work we've decided to buy SSDs to speed up our computers. We'd also like to upgrade from Windows 7 to Windows 8.1 (read clean install) I'm talking about 10 computers which going to have a fully clean installation. Is there any trick I can use to avoid installing Windows 10 times? The computers (most of them) are different in hardware, so I think duping is no good option. What can I do? I'd like to spend as less time as possible because all computers are going to need SQL Management Studio and Visual Studio 2012/2013. Thanks!

  Read the article

• Windows Network copy and access denied randomly

  - by The King

  I have a windows 2008 R2 server and I now installed a new bigger HDD into it. I wanted to copy big AVI files to the new server hdd what is shared on the local network. I have write access to the servers hdd and I can successfully copy smaller files to it. But when I copy bigger files more than 500MB randomly on the copy I get Access Deny message. If I use RDP I can copy files through RDP client. I checked error messages at the server but I didn't found any error about this access deny. Because of RDP copy works I don't think that this could be hardware error. I think this is some kind of software setting error. Someone has faced this kind of error? Or somebody has idea what could cause or how to find the root of the problem?

  Read the article

• Can't unlock locked screen, in Ubuntu 12

  - by Camille Goudeseune

  After locking the screen (with a keystroke bound to xlock -nice 8 -mode blank), I can unlock the screen as expected, but only within a few minutes. After being locked overnight, when I hit a key (even Ctrl+Alt combos), the screen stays black with just a brief white flash across the middle of both monitors. The workaround is to ssh in from another host and restart X. Some months ago, this happened every few weeks. By now it happens almost every morning. How do I even start to diagnose this? What might I look for in log files? (The intermittency is particularly troubling.) Failing that, is there an alternative to xlock aka xlockmore? Hardware: 3-year-old HP minitower, GEForce 9800 GT, two Asus LCD monitors. Software: Ubuntu 12.04.2 LTS. Window manager awesome-wm. NVidia driver 304.88. XLock version xlockmore-5.31.

  Read the article

• How to make sure you server NIC performance is at best on Windows?

  - by Bobb

  I realised that I followed some obscure paper on setting NICs on Windows for too long. It might be outdated with new hardware released in past couple of years and with W2008R2. I read a bit about offloading and RSS settings on Windows and I realiased that it is very much circumstantial. Noone can really say - enable that and disable this. etc. So what I really want is for my next server try and setup testing environment and measure how my particular application will behave with different settings. The target is going to be latency of TCP primarily. Please note I am talking about latency inside the box. Are there precision tools for Windows to measure latency (down to microseconds)? P.S. I know this is not easy question. Windows time drift is awful problem for any precision test but still I am sure I am not the fist person to need that... Please share your experience

  Read the article

• Windows 7 automatically install usb driver

  - by Dan

  I have tried to install usb driver for Samsung arndale on Windows 7. Now it has two entries in Device Manager. I can not uninstall the one with question mark. If I uninstall both of them, when I plug in the hardware, Windows 7 will automatically install both of the entries when the circuit pulg in. I don't get the chance to choose the right driver. When I try to update the wrong driver, it says found the driver but can not install it.

  Read the article

• Portable Display doesn't work anymore

  - by RipCord

  My USB portable monitor will not work since I installed the hard drive onto an HP laptop. I have installed all the new hardware drivers and do not have any more device issues in device manager view. My old laptop was a lenovo. The new one is an HP. The system seems to recognize devices that I connect via, usb but the portable display still does not show anything on the screen. It is probably a conflict in the registry but I'm not sure how to find it and the Power User does not have the luxury of letting me troubleshoot for hours to isolate the problem.

  Read the article

• "SIOCSIFADDR: No such device" after restoring backup

  - by Paul Tomblin

  I bought some new hardware, and tried to restore my backup on it. When I boot, I don't get a network connection. If I type "ifup eth0" on the command line, I see the messages: SIOCSIFADDR: No such device eth0: No such device lspci shows an ethernet controller (Intel 82546GB). ifconfig does not show any controller except loopback. I tried installing bare Debian on the machine and the network worked then, but now I want to make it like my old machine was. Googling this problem only seems to find people having this problem in VMs. I'm not in a VM.

  Read the article

• Is it a good idea to take onsite/offsite backups of server images?

  - by ServerAdminGuy45

  Assuming a non-virtualized environment it a good idea to take actual images of servers (using something like Acronis True Image) and store them on\off site? Backing up data is great but I feel it would be good to have copies of OS images in the event hardware dies or an upgrade gets botched I can always revert back. What would be your recommended way to do this (preferably using a NAS and an online backup service)? I was talking with the Iron Mountain folks and the service they described is more geared toward taking incremental snapshots of data. I'm not sure if there's a way to backup images in an incremental way such that only the changes between them are saved (that way I'm not wasting X GB each time I take an image).

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• DNS Pointer to old server name

  - by TechKnow Dude

  We have a SBS2003 server that was migrated to a new hardware platform, the computer name has changed but the domain is the same. The desktop's are trying to do offline files to the old server name. There is a nslookup entry for the old server name and a DNS entry for the old server. How do we safely remove the old DNS entry without breaking the computer offline folder storage locally. Can we change the pointing location on the offline file storage to point to the new server name.

  Read the article

< Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >