Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 288/383 | < Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >

• bond0:0 + define virtual IP

  - by yael

  in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• I can't connect to internet via lan cable because 2032 battery died and my bios bios info is now empty [closed]

  - by Rand Om Guy

  I have a compaq CQ61-112SL from about 5 years now... the main battery is almost dead, doesn't keep more then 10 minutes. anyway my problem is that my motherboard battery didn't have any more energy left a few days ago and since then I can't access internet through lan cable but only via wifi. I need cable though. I saw that on my BIOS setup page there were a bunch of parameters missing like serial number, UUID, product number and stuff like that. Also when I start the notebook it prints something like : No serial found. or something like that. I don't really know if the reason why my lan cable doesn't work is the empty BIOS but i assume that's it. If it's not please enlighten me. Or anyway tell me how to update the serial number and product number to the real ones (instead of the 0000000000000 that is now in my bios). I downloaded HP DMI which should make it possible to set these variables on the BIOS but i'm on Windows 8 64bit and the executable file that I need to open for my laptop model says it can't run on 64 bit.

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

• allow spoofing when using tun

  - by Johnny

  I have a working openvpn setup with a server and a number of clients. How would i go around allowing IP spoofing through the openvpn server? (to demonstrate security concepts)? A normal ping from client to server goes through all right: root@client: hping3 10.8.0.1 HPING 10.8.0.1 (tun0 10.8.0.1): NO FLAGS are set, 40 headers + 0 data bytes len=40 ip=10.8.0.1 ttl=64 DF id=0 sport=0 flags=RA seq=0 win=0 rtt=124.7 ms root@server:/etc/openvpn# tcpdump -n -i tun0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tun0, link-type RAW (Raw IP), capture size 65535 bytes 10:17:51.734167 IP 10.8.0.6.2146 > 10.8.0.1.0: Flags [], win 512, length 0 But when spoofing a packet, it does not arrive at the openvpn server: root@client: hping3 -a 10.0.8.120 10.8.0.1 HPING 10.8.0.1 (tun0 10.8.0.1): NO FLAGS are set, 40 headers + 0 data bytes root@server:/etc/openvpn# tcpdump -n -i tun0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tun0, link-type RAW (Raw IP), capture size 65535 bytes My current config files server.conf local X.Y.Z.P port 80 proto tcp dev tun ca ca.crt cert server.crt key server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1 bypass-dhcp" keepalive 10 120 comp-lzo persist-key persist-tun persist-local-ip status openvpn-status.log verb 3 client.conf client dev tun proto tcp remote MYHOST..amazonaws.com 80 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3

  Read the article

• windows 2008 r2 iis worker proccess memory usage increase

  - by nLL

  I have this web site written in c#. around 400-500 users online at any time. it was on windows 2008 32 bit machine before and never ever locked/slowed down due to increased memory consumption up until i upgraded it's server to win 2008 r2 64 bit. Old server had only 4 gig ram and quad core cpu at 2ghz. site was working just fine. since i've upgraded the server i noticed (2 times with in 10 days) it started to eat ram. last night it went up to 4 gb ram. with ram increase response slows down quite a lot. recycling app pool doesn't help. I have to restart it's worker process to recover. i've noticed this usually happens if there are continuous errors. as i didn't change anything in the code am i safe to assume it is not related to memory leak in the code? did anyone came across something like that? same thing happens if i create continuous errors with classic asp. thanks

  Read the article

• Explorer constantly hanging

  - by user978122

  So I'm running Windows 7 Ultimate (x64) an AMD 8150 on an Asus Crosshair V motherboard with all the latest and greatest patches, and I am experiencing frequent Explorer freezes. I've included the information I've grepped from the Event Viewer below: The program Explorer.EXE version 6.1.7601.17567 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel. Process ID: 13a4 Start Time: 01cdb2968999c6fd Termination Time: 0 Application Path: C:\Windows\Explorer.EXE Report Id: c000ba44-1e8b-11e2-9ae7-000272ddf2b0 - System - Provider [ Name] Application Hang - EventID 1002 [ Qualifiers] 0 Level 2 Task 101 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2012-10-25T10:08:44.000000000Z EventRecordID 14626 Channel Application Computer RyanMain-PC Security - EventData Explorer.EXE 6.1.7601.17567 13a4 01cdb2968999c6fd 0 C:\Windows\Explorer.EXE c000ba44-1e8b-11e2-9ae7-000272ddf2b0 430072006F00730073002D0074006800720065006100640000000000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00720043 0073006F 002D0073 00680074 0008: 00650072 00640061 00000000 In Bytes 0000: 43 00 72 00 6F 00 73 00 C.r.o.s. 0008: 73 00 2D 00 74 00 68 00 s.-.t.h. 0010: 72 00 65 00 61 00 64 00 r.e.a.d. 0018: 00 00 00 00 .... Any idea what "Cross-thread" here means?

  Read the article

• Tuning up a MySQL server

  - by NinjaCat

  I inherited a mysql server, and so I've started with running the MySQLTuner.pl script. I am not a MySQL expert but I can see that there is definitely a mess here. I'm not looking to go after every single thing that needs fixing and tuning, but I do want to grab the major, low hanging fruit. Total Memory on the system is: 512MB. Yes, I know it's low, but it's what we have for the time being. Here's what the script had to say: General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Your applications are not closing MySQL connections properly Variables to adjust: query_cache_limit (> 1M, or use smaller result sets) tmp_table_size (> 16M) max_heap_table_size (> 16M) table_cache (> 64) innodb_buffer_pool_size (>= 326M) For the variables that it recommends that I adjust, I don't even see most of them in the mysql.cnf file. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_buffer_pool_size = 220M innodb_flush_log_at_trx_commit = 2 innodb_file_per_table = 1 innodb_thread_concurrency = 32 skip-locking big-tables max_connections = 50 innodb_lock_wait_timeout = 600 slave_transaction_retries = 10 innodb_table_locks = 0 innodb_additional_mem_pool_size = 20M user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = localhost key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 4 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M log_error = /var/log/mysql/error.log expire_logs_days = 10 max_binlog_size = 100M skip-locking innodb_file_per_table = 1 big-tables [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M !includedir /etc/mysql/conf.d/

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• Ram configuration 4x4 or 2x8?

  - by Carl B

  I am looking to upgrade my Ram to 16gigs and I am wondering if there is any distinct advantage of the way I do it. That being a 4x4 or 2x8 set up. In all my searching there have been a number of pros for each profile. I can find no benchmarck results for either setup as a compaison. So, if there are 2 profiles of the same speed, same voltage, same timing and same cas what would perform better or have a better over all benafit? A few examples from my search - a 4x4 set would lend a benafit in that if one stick failed, you only lose 25% of your Ram vs 50% in a 2x8 set up. a 2x8 set up would have less strain on the memory controler and motherboard. a 2x8 would generate less heat. a 2x8 set up is easier to over clock (not part of my need, but alot of the comparisons circled around the overclocability ease of the 2 stick set up). There is one outstanding benafit that I have found in at least the target company I have looked at and that is price. The 2x8 is nearly half the cost. My motherboard supports a max of 16 gigs and I have a 64 bit OS. Has anyone seen any performance comparisons or is 16 gb just 16 gb no matter how you slice it? And is there any merit to the above pros? Edit: as per the mobo specs - Main Memory • Supports four unbuffered DIMM of 1.5 Volt DDR3 800/1066/1333/1600*/1800*/2133* (OC) DRAM, 16GB Max

  Read the article

• linux networking: how to redirect incoming connections from old server to new server?

  - by aliz

  hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

  Read the article

• Intel HD Graphics vs NVIDIA Quadro FX 380 PCI-E

  - by Michael

  I recently purchased an Acer Veriton which has an i5-650 processor, Windows 7 Pro (64 bit) and Intel HD Graphics listed as the video card. I also purchased a PNY nVIDIA Quadro FX 380 PCI-E card for improved picture and home video viewing and editing. I have already replaced the original 300 wattt power supply to a 430 watt Antec Truepower I had on hand and boosted the RAM to 8 gigs from the original 4. Question 1) Am I getting any improvement in visual quality or system speed with the Quadro or is it a waste of money and I should just save up to buy a bigger video card? This card was on sale for $115. If I am getting improvement then I need to ask another question. Question 2) Instructions for the Quadro installation are as follows... 1--Uninstall the existing VGA driver. -Remove the existing Display Driver via "Add or Remove Porgrams". -Shut down your computer. 2--Remove your Existing Graphics Board (or Disable Integrated 3D Graphics Controller). skipping instructions on how to remove existing graphics board -Systems with integrated (also know as on-board) 3D graphics may require you to disable the integrated 3D graphics system. Consult the owners or vendor manual that came with your PC on how to properly do this. So is the Intel HD Graphics considered a 3D graphics controller? If so should I just contact Acer or can anyone give me instructions? Thanks in advance for any help.

  Read the article

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Copying files to my laptop makes them locked

  - by John

  When I save files from e.g. remote desktop or from an email (outlook) attachments, or from skype even to my local machine they show a locked Icon on the file. Then e.g. SQL Server doesn't let me restore backups as it says the operating system doesn't have access to the file. I've had success fixing this by setting the ownership of the parent folder to my user and then let it apply to sub folders. Also sometimes I need to click - Proerties - Security - Advanced - Change Permmissions, then check "change child permissions..." and apply on the parent dir. I'm using Windows 7 64 bit Proffessional, on HP Probook 4530, and I have a administrator user. This is a real pain to do everytime. I suspect it might be because of HP software that came with the laptop, I think there is drive encryption as part of the protect tools. Although I'm hoping there's something in windows i can set to change the behaviour to not lock these files.

  Read the article

• VM load and ping problems after replacing server motherboard

  - by Andre

  Recently, we had to replace the motherboard of one of our servers. The procedure was done by IBM as it had guarantee. The server runs ESXi 5.1, with several virtual machines, including our main mail server (Domino) and a file server. After the replacing the motherboard and staring the VMs, ESXi asked us if we had moved it or copied (different motherboard is like a different computer). We clicked the latter. We started each machine and after some basic reconfiguration, all of them were up. However, we have been having problems with the mail server, it has been acting really slow at times (this could be when it syncs with the secondary mail server) and we have been checking with Centreon (a Nagios frontend) that its CPU load has been a bit high at times and ping response too. There was a moment this morning in which I tried connecting via SSH console and it was really slow to show login and basic commands like ifconfig and top. This particular mail server is a CentOS 4.4.7 64-bit. The little configuring we had to do after restarting it was to configure the network connection as it was resolving through DHCP. Our mail software is Lotus Notes server 9. Do you know of any way in which this replacement may be causing these difficulties, and how to fix it? Thanks.

  Read the article

• how to get ip address of a PPP(Point-to-Point Protocol) network interface?

  - by Xsmael

  I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

  Read the article

• How to use the outcome of a formula as the value for Vlookup or another IF formula

  - by Steven

  Ok I will try to explain my issue effectively. I am making a GPA sheet in which the value out of 100 is computer in to a GPA value and then in to a letter. In cell N5 i have the value of all their grades (formula: =H3+H4+H5) Now in cell (j6) I have a formula which is giving them a number depending on the value calculated in N5 (Formula: =IF(AND(N5>=60,N5<=63.999),"2.0",IF(AND(N5>=64,N5<=66.999),"2.25",IF(AND(N5>=67,N5<=69.999),"2.4",IF(AND(N5>=70,N5<=73.999),"2.5",IF(AND(N5>=74,N5<=76.999),"2.75",IF(AND(N5>=77,N5<=79.999),"2.9",IF(AND(N5>=80,N5<=83.999),"3.0",IF(AND(N5>=84,N5<=86.999),"3.25",IF(AND(N5>=87,N5<=89.999),"3.4",IF(AND(N5>=90,N5<=93.999),"3.50",IF(AND(N5>=94,N5<=96.999),"3.75",IF(AND(N5>=97,N5<=100),"4",IF(AND(N5<=59.999),"0"))))))))))))) Still no problem... as the values I was looking for comes out (example 84.2 shows up as 3.25 as I wanted). However here comes the problem.... I have tried to use the outcome in J6 to do Vlookup or another if formula, however excel does not seem to recognize the value in J6. For example: =VLOOKUP(j6,B3:C15,2,FALSE)... this returns N/A however if I enter =VLOOKUP(3.25,B3:C15,2,FALSE) it gives me what im looking for. It seems that excel will not register the outcome of my formula as a number. What can I do please?

  Read the article

• Outlook 2010 - Missing New Mail Envelope Icon

  - by sdoca

  I've seen a number of posts related to this issue, but none with a solution that works for me. I have: Windows 7 Professional 64 bit Office/Outlook 2010 "Show an envelope icon in the taskbar" checked "Hide When Minmized" selected "Show icon and notifications" selected for Outlook in my taskbar settings This used to show me the envelope icon in my notifications area. Then something happened with my user profile and the sys admins created me a new one. Since then, the envelope only displays if Outlook is not minimized. It doesn't matter if I unselect "Hide When Minmized", the icon still doesn't display when new mail arrives. If I select "Display a Desktop Alert", then the icon is displayed. However, I HATE the desktop alert as I find it too intrusive/distracting. Is there some way to just get the envelope icon working (again)? UPDATE More testing and sometimes I will and sometimes I won't get an envelope icon with the desktop alert turned on. This is driving me nuts!! UPDATE TWO I like my notification area of the taskbar to be clean. So, all icons are set to "Only show notifications" except for Outlook as noted above. I've noticed the envelope icon is being displayed in the expanded notification area when I click on the up arrow to view all icons. So, it is being added to the notification area, but not displayed. It's a rather useless feature now...

  Read the article

• Ping not working

  - by Nishant

  Ping is not working to and from this IP to my computer. inet addr:10.125.104.4 Bcast:10.125.111.255 Mask:255.255.240.0 My computer is like this Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.125.65.75 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 10.125.64.6 We both CAN reach the common gateway IP , 10.125.96.6 . What should I check ? What is the barrier in sending info if we both have a common gateway that is pingable ? Besides I can login to a intermediate server and ssh to this server also !!

  Read the article

• PHP unable to allocate memory.

  - by AlReece45

  On my way to the office this morning, every website on our shared VPS started giving the same error (several times, not the typical memory_limit error which is fatal): Warning: Unknown: Unable to allocate memory for pool. in Unknown on line 0 The shared server is a 64-bit OpenVZ container running cPanel. There are only ~6 VPSes on the host-- this is the largest one at only 4GB. The host itself has 24GB RAM. As the below graphs show, the memory usage on the host and VPS are both rather low. CPU Usage/Disk/Host all seem to be normal. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. Apache 2.2, PHP 5.2 (mod_php) Restarting Apache has corrected the problem for now. However, I'd like to prevent it from happening again and I'm not sure what was limiting the memory. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. There's seems to be plenty of memory: what caused this error? VPS Memory Usage Host Memory Usage APC Information apc.ttl=0 apc.shm_size=0 apc.mmap_file_mask=(blank) 1 Segment(s) with 32.0 MBytes (mmap memory, pthread mutex locking)

  Read the article

• Diagnosing RAM issues

  - by TaylorND

  I have an old Acer Aspire T180 desktop. The specs are as follows: AMD Athlon 64 3800+ 2.4GHz 1GB DDR2 SDRAM 160GB DVD-Writer (DVD±R/±RW) Gigabit Ethernet 17" Active Matrix TFT Color LCD Windows Vista Home Basic Mini-tower AST180-UA381B According to the information in the computer's documentation the computer comes with 1 GB of RAM. It has two DDR2 SDRAM sticks. I used to have Windows Vista installed. Then I removed it and install Windows 7, and now I have since removed Windows 7 and installed Windows XP. According to Windows XP with both RAM sticks in the computer has 768 MB. Isn't this supposed to be 1 GB of RAM or 1024 MB of RAM? Is the amount of RAM installed only partly used by the Operating System? Is there's something I'm missing? If I remove either one of the RAM sticks I'm left with 448 MB of RAM. These numbers don't seem to add up. If each of the RAM sticks contains at least 448 MB of RAM shouldn't they (both being in) provide 896 MB of RAM. Even then, isn't that less than a GB of RAM? I'm not too experienced in hardware so I thought this would be the best place to ask. As a follow up question, is the RAM I have enough to run/multitask with Windows XP efficiently? I plan to do a lot of computing with the system (although not gaming), should I invest in more RAM?

  Read the article

• Clone a Windows Installation to a 3TB Hard Drive; MBR to GPT

  - by DanBlakemore

  I have Windows 7 Professional 64-bit installed on my desktop. Unfortunately for me and my wallet my hard drive is failing. I have purchased a 3TB hard drive as a replacement for my current 2TB drive. I would like to avoid as much hassle as possible in moving to this new drive so I would like to copy my current partition to the new drive using Gparted. The problem is that I suspect that my current partition is MBR, and I need GPT on my new drive since it is 3TB. Can I simply copy the MBR partition onto the new disk and then convert it to GPT after the fact (can you even convert the type of a partition)? Or would I need to somehow copy the contents of the partition into a GPT partition on the new drive? How do I go about making this transistion? Also, are there any issues I should be wary of booting to a GPT partition? If it matters, my motherboard is 1 year old as of May, 2012. Edit: My motherboard is 1 day old. My old one does not have UEFI compatibility, so I decided to make an upgrade to Intel today given that I would need a UEFI motherboard to use my new HDD. How much can I use a dying hard drive (bad sectors according to Hitachi Drive Fitness Test)? I have assumed not at all, to be safe.

  Read the article

• Server not resolving after restart

  - by DomainSoil

  I restarted our server today, and now cannot for the life of me get anything to resolve... I suspect it has something to do with our routes. I've tried numerous Google results to no avail. Here is as far as I've gotten: [root@www ~]# route -n Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.101 0.0.0.0 255.255.255.255 UH 0 0 0 eth1 0.0.0.0 192.168.1.101 0.0.0.0 UG 0 0 0 eth1 Things you need to know: Our server (CentOS 6.3) runs two virtual machines, one live, and one development. They mirror each other as much as possible, but I can't find where I've went wrong with the live server. The dev server works fine. [root@www ~]# ifconfig eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet6 addr: xxxx:xxx:xxxx:xxxx:xxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118206 errors:0 dropped:0 overruns:0 frame:0 TX packets:165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7825749 (7.4 Mib) TX bytes:7146 (69.2 KiB) Interrupt:28 [root@www ~]# /etc/init.d/network status Configured devices: lo Auto eth0 Currently active devices: lo eth1 If there is any other information you need, please don't hesitate to ask!

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• Low-traffic WordPress website on Apache keeps crashing server

  - by OC2PS

  I have recently moved my low-moderate traffic (1000 UAUs, 5000 pageviews on a busy day) website from shared hosting to a Centos 6 64-bit VPS with Apache and cPanel running on 4 quad-core processor (likely oversold) and 3GB memory (Xen). We've had problems from the beginning. The server keeps crashing. It seems PHP keeps expanding till it consumes all the memory and crashes the server. Some folks have suggested that I should abandon Apache/cPanel/PHP/mySQL and go with nginX/Varnish/PHP-FPM/SQLite. But that's just not possible for me as I am not very tech savvy and need a simple GUI like cPanel to be able to manage the mundane management tasks (can't afford to hire system administrator or get fully managed hosting). I have come across several posts discussing optimization of Apache for WordPress. But all of these lead to articles that are pretty dated such as this ~4 year old one from Jan 2009 - http://thethemefoundry.com/blog/optimize-apache-wordpress/ The article is pretty detailed and seems helpful, but I stumble even on the first step. My httpd.conf only has 2 loadmodule commands LoadModule fastinclude_module modules/mod_fastinclude.so LoadModule bwlimited_module modules/mod_bwlimited.so So I go total bust right there. Further, my httpd.conf says Direct modifications to the Apache configuration file may be lost upon subsequent regeneration of the configuration file. To have modifications retained, all modifications must be checked into the configuration system by running: /usr/local/cpanel/bin/apache_conf_distiller I am having trouble finding where to change the modules in WHM. Please can someone help me with updated guidelines on how to optimize Apache for WordPress? Many thanks! P.S. The WordPress installation also has WP Super Cache installed. P.P.S. I also have phpBB, OpenCart, and Menalto Gallery installed.

  Read the article

< Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >