Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 289/383 | < Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >

• Replaced CPU and black screen but no beep?

  - by luke

  I'm having a bit of trouble with a GIGABYTE GA-MA78G-DS3H (rev. 2.0) motherboard. Recently when trying to clean my AMD Phenom II X 4 CPU, I dropped it and broke some pins. I have now brought a Athlon 64 X2 5400+. However, it does not seem to work. To begin with, I cleared the CMOS via the jumper located near the battery. This was because I had my AMD Phenom II overclocked and did not wish for the same voltage to go to the new CPU. I then tried booting with the monitor plugged into the chipsets VGA but no luck. No signal was sent to the monitor, and the monitor just went into standby. I then tried it off the graphics card but the same happened again. Then I tried to check whether the CPU could executed some BIOS codes by stripping the RAM out and making sure a speaker was plugged in but no beeps could be heard. I replaced the speaker and tried again but no luck. The CPU is brand-new so what is going wrong?

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

• How do I speed up and cache mmap file access over NFS on Linux?

  - by Zan Lynx

  The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

  Read the article

• Nginx , Apache , Mysql , Memcache with server 4G ram. How optimize to enought memory?

  - by TomSawyer

  i have 1 dedicated server with Nginx proxy for Apache. Memcache, mysql, 4G Ram. These day, my visitor on my site wasn't increased, but my server get overload always in some specified time. (9AM - 15PM) Ram in use is increased second by second to full. that's moment, my server will get overload. i have to kill all apache , mysql service and reboot it to get free memory. that's the circle. here is my ram in use at the moment 160(nginx) 220(apache) 512(memcache) 924(mysql) here's process number 4(nginx) 14(apache) 5(memcache) 20(mysql) and here's my my.cnf config. someone can help me to optimize it? [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql skip-locking skip-networking skip-name-resolve # enable log-slow-queries log-slow-queries = /var/log/mysql-slow-queries.log long_query_time=3 max_connections=200 wait_timeout=64 connect_timeout = 10 interactive_timeout = 25 thread_stack = 512K max_allowed_packet=16M table_cache=1500 read_buffer_size=4M join_buffer_size=4M sort_buffer_size=4M read_rnd_buffer_size = 4M max_heap_table_size=256M tmp_table_size=256M thread_cache=256 query_cache_type=1 query_cache_limit=4M query_cache_size=16M thread_concurrency=8 myisam_sort_buffer_size=128M # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 [mysqldump] quick max_allowed_packet=16M [mysql] no-auto-rehash [isamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [myisamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [mysqlhotcopy] interactive-timeout [mysql.server] user=mysql basedir=/var/lib [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid

  Read the article

• Suggestions for cleaning up the mess after removing the "system tool" virus?

  - by Ross

  Hi! Last night I got infected with the "System Tool" virus. For those who don't know it disallows the user from executing any software, changes the desktop, stops all security software from running, and continually requests that you buy a Trojan security software. It took me a few hours but I finally managed to remove the software. To do this I went into my Ubuntu partition and searched out files that had been created around the time that I got infected and deleted the executable. Then I went back into my W7 partition and ran an MBAM full scan, an MSE full scan, an AVG bootable USB scan, and ran a ClamAV scan from my Ubuntu partition (Together these found 3 more infected executables). I also ran a Ccleaner full sweep and the registry cleaner just in case. I think I have found all of the problems but am still concerned that there might be a payload leftover from the virus that I didn't find. Do you have any suggestions of what else I can do to be sure. Just FYI I use W7 64 bit and MSE as my primary antivirus. I was using chrome when I got infected and it seems that it was due to a slightly out of date Java installation (MSE gave me a warning that the website had used a Java exploit and then my desktop changed to the classic "System Tools" desktop) Thank you very much for your help.

  Read the article

• Unwanted forced authentication after server restart (Win 2k3)

  - by Felthragar

  We're running a Win 2k3 R2 Standard 64-bit edition server. On this server we're running a fileserver and the ability to allow remote login to our network through vpn. We do not currently utilize a domain setup, all user accounts are local accounts on the server. Each employee is given a unique account to login to the server. The password is a randomly generated 16 character long string, which makes it hard to remember. What we've done is basicly had the password stored on the client machine (standard "Remember Me" functionality). This has worked well. However, last night our server automatically restarted after an automatic update. After that, some of our employees, myself included, had to re-authenticate with the server, submitting our credentials again. Then again, some others did not have to re-authenticate. Do you guys have any idea why this is? Is there a setting to prevent this? I've checked the logs but I couldn't find anything of interest. Then again I'm not really sure what I'm looking for. Thanks in advance, I'll try to answer any additional questions you may have. Edit: When I say "login" or "authenticate" I mean through the standard windows samba protocol. Edit 2: Ok, new day. Tonight the server restarted again, and the same two clients that had to re-authenticate yesterday had to re-authenticate today as well. The rest did not.

  Read the article

• What is the risk of introducing non standard image machines to a corporate environment

  - by Troy Hunt

  I’m after some feedback from those in the managed desktop or network security space on the risks of introducing machines that are not built on a standard desktop image into a large corporate environment. This particular context relates to the standard corporate image (32 bit Win XP) in a large multi-national not being suitable for a particular segment of users. In short, I’m looking at what hurdles we might come across by proposing the introduction of machines which are built and maintained by a handful of software developers and not based on the corporate desktop image (proposing 64 bit Win 7). I suspect the barriers are primarily around virus definition updates, the rollout of service packs and patches and the compatibility of existing applications with the newer OS. In terms of viruses and software updates, if machines were using common virus protection software with automated updates and using Windows Update for service packs and patches, is there still a viable risk to the corporate environment? For that matter, are large corporate environments normally vulnerable to the introduction of a machine not based on a standard image? I’m trying to get my head around how real the risk of infection and other adverse events are from machines being plugged into the network. There are multiple scenarios outside of just the example above where this might happen (i.e. a vendor plugging in a machine for internet access during a presentation). Would a large corporate network normally be sufficiently hardened against such innocuous activity? I appreciate the theory as to why policies such as standard desktop images exist, I’m just interested in the actual, practical risk and how much a network should be protected by means other than what is managed on individual PCs.

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• SQL Server Replication Backup

  - by user18039

  Hi We have a new system that runs on SQL Server 2008 r2 64-bit. There is a primary on-line transactional processing (OLTP) database that accepts a high volume of updates from several thousand Point of Sale systems at stores around the country. In order to protect this vital function, I have decided to introduce a dedicated reporting database server - from which multiple users will run some pretty complex reports. I realise that there were a number of choices but I decided to use Transaction Replication as the mechanism for copying the data from the OLTP database to the new reporting database - one way replication. The solution has worked well in test. I'm now being asked what changes need to be made to the backup policy to cover the architectural changes. I have read pages such as MSDN:Strategies for Backing Up and Restoring Snapshot and Transactional Replication but I think these are overkill for my solution. In fact, my current thinking is that we simply need to continue making backups of the OLTP data and logs. If the Reporting db or any of the system replication (eg distribution) databases fail then it's no big deal - we can clear all down then re-create the replication. I realise that taking a complete snapshot of the OLTP would be time consuming (approx 5 hours) but I'd be more relaxed about this that trying to restore backups of the various data and log files in the correct sequence. My view is that the complex strategies set out in the MSDN article would only be the way to go for a more complex replication solution than I have, eg if there were multiple subscribers with 2-way replication. Would you agree? I'd be grateful for any advice. Many thanks, Rob.,

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• Oracle: 1 Large Server vs. 2 Smaller Servers?

  - by nvahalik

  We are in the planning stages of setting up our production Oracle 10gR2 environment. Our budget gives us the ability to buy 2 processor licenses of Oracle DB Standard Edition. We have minimal experience with Oracle so I'll defer to anyone who has used it. We are trying to decide if we should set up a single dual quad-core box or 2 individual quad-core boxes in a RAC configuration. Our DB right now is about 60 GB, and at our peak, we'll have up to 150 concurrent users. Most of the big stuff is done via batch processing at night. My gut tells me that having 2 boxes in a RAC configuration can't be a bad thing because it provides a true hardware failover solution. DB stored in a shared LUN on a SAN via iSCSI. Plus if we ever need to add capacity, we already have boxes in place that can be upgraded with extra procs (I assume with zero downtime, since it's set up in a RAC config) if we add extra licenses, or RAM. Does RAC have any performance penalties? Will it add extra latency? Is there any true advantage for having dual processor boxes running these systems? If we build out the Oracle boxes with special hardware: hardware iSCSI cards, TOE NICs, will these boxes be solid? We are deploying on 64-bit Windows. So what would you do? One box or two?

  Read the article

• Ubuntu 12.04 as router with 2 nic

  - by Blue Gene

  I have been trying this setup for weeks and still can not make this to work... ubuntu 12.04 64 bit with 2 nic nic1: eth0:192.168.2.33 -static ip with internet access (connected to modem) nic2: eth1:192.168.1.2 -static ip connected to LAN. enabled ip_forward on ubuntu box net_ip_forward = 1 on the LAN with ip address 192.168.1.5 specified gateway as 192.168.1.2 and able to ping gateway.But can not ping public address.What am i missing? on router box: route -n Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 tried ip route add 192.168.2.0/24 via 192.168.1.2 dev eth0 route -n on LAN 192.168.1.5 Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.2 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 192.168.1.2 255.255.255.0 UG 0 0 0 eth0 iptables default policy is to accept all. tracepath 8.8.8.8 from LAN 1: 192.168.1.5 0.060ms pmtu 1500 1: 192.168.1.2 3.367ms 1: 192.168.1.2 3.764ms 2: no reply Is there a way to make this work,other than NAT ing.

  Read the article

• sql server uninstallation issue

  - by angel

  I'm unable to remove SQL Server 2008 sp1 completely from my system. I'm using windows 7 ultimate. Everytime I try uninstalling it i get the following error. How can I remove it? here is the log: Overall summary: Final result: Failed: see details below Exit code (Decimal): -2068643839 Exit facility code: 1203 Exit error code: 1 Exit message: Failed: see details below Start time: 2013-06-24 21:10:38 End time: 2013-06-24 21:21:17 Requested action: Uninstall Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\sql_rs_Cpu64_1.log Exception help link: http://go.microsoft.com/fwlink?LinkId=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.0.1600.22 Machine Properties: Machine name: ABHI-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: United States OS language: English (United States) OS architecture: x64 Process architecture: 64 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Sql Server 2008 MSSQLSERVER MSRS10.MSSQLSERVER Reporting Services 1033 Enterprise Edition 10.0.1600.22 No Sql Server 2008 Management Tools - Basic 10.0.1600.22 No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation edition: ENTERPRISE User Input Settings: ACTION: Uninstall CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini FEATURES: RS,SSMS,SNAC_SDK,CE_RUNTIME,CE_TOOLS,SNAC HELP: False INDICATEPROGRESS: False INSTANCEID: INSTANCENAME: MSSQLSERVER MEDIASOURCE: QUIET: False QUIETSIMPLE: False X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini Detailed results: Feature: SQL Client Connectivity Status: Skipped MSI status: Passed Configuration status: Passed Feature: SQL Client Connectivity SDK Status: Skipped MSI status: Passed Configuration status: Passed Feature: Reporting Services Status: Failed: see logs for details MSI status: Passed Configuration status: Failed: see details below Configuration error code: 0xFFD65603 Configuration error description: Input string was not in a correct format. Configuration log: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\Detail.txt Feature: SQL Compact Edition Tools Status: Passed MSI status: Passed Configuration status: Passed Feature: SQL Compact Edition Runtime Status: Skipped MSI status: Passed Configuration status: Passed Feature: Management Tools - Basic Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\SystemConfigurationCheck_Report.htm

  Read the article

• No outbound internet connection after restarting CentOS 6.3

  - by wnstnsmth

  After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

  Read the article

• Security Token for Mac/Linux/Windows, self-managed, pref. open source?

  - by DevelopersDevelopersDevelopers

  I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

  Read the article

• Can't access YouTube

  - by Agentleader1

  I can not seem to connect to YouTube at all. If I connect directly to YouTube (youtube.com) I get this: And if I try to connect via video directly (youtube.com/watch?v=), I get this: Here's how this isn't a web issue: I have malware on my computer I believe. And the question here is, how do I get rid of it, or what possible issue could this be? I can verify this is not a website issue or wifi issue, I've tried to connect on another computer in my wifi, and it worked. It is the local machine issue. I've tried to get rid of malware at my best and also have tried to disable possible virus extensions. All can out as the same result: no help. Also, I am unable to find these hiding viruses. I used malware-bytes and Microsoft Security Essentials. Edit: This is OBVIOUSLY Windows. I am currently running on a laptop Windows 7 Home Premium 4gb ram 64-bit os Lifebook series manufactured by Fujitsu America, Inc. Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz nslookup youtube.com:

  Read the article

• Power surge PC damage: How can I test all components of my PC without access to a second computer?

  - by Doug T.

  Ever since we had some crazy power surges last week my 64 bit Windows 7 PC has been acting strange. My USB network adapter disconnects from the wireless and can't detect the signal. I have to disable/reenable the adapter to detect it again. Also my wife has reported that the PC has rebooted a few times while I'm not sitting at it. Today I finally caught the reboot while I was using the PC. I got this blue screen of death. Stop Code 0x00000109: "Modification of system code or a critical data structure was detected." I followed the advice at the linked article and ran a memory test. I used memtest86 and its already found around 300,000 errors out of 8 gigs of ram. Now I'm worried -- what are the odds this is isolated to just my memory and not just a system wide problem? Isn't there a good chance that many other components are fried? More importantly, how can I test those other components? Are there tools similar to memtest I can use to test my motherboard/video card/power supply? If these are vender specific, is it typical for vendors to provide testing tools?

  Read the article

• Utilu IE Collection IE6 crashes under Windows 7

  - by Aron

  I've installed Utilu IE Collection under Windows 7 64-bit, but am unable to successfully run IE6 (specifically, "Internet Explorer 6.0 (6.00.2900.2180)"). I haven't tried other versions of IE from the package, so their behavior is unknown. It starts up fine, but the address bar isn't shown. (Attempted to post image, but I'm a newbie on SU and it wouldn't let me. Can be found here.) View-Toolbars shows 'Address Bar' already selected. If I try to (de-)select Address Bar in that list, it crashes: Problem signature: Problem Event Name: APPCRASH Application Name: iexplore.exe Application Version: 6.0.2900.2180 Application Timestamp: 41107b81 Fault Module Name: StackHash_e162 Fault Module Version: 0.0.0.0 Fault Module Timestamp: 00000000 Exception Code: c0000005 Exception Offset: 00000000 OS Version: 6.1.7600.2.0.0.256.48 Locale ID: 1033 Additional Information 1: e162 Additional Information 2: e1625455580a00d3fda64a8cdf366fbb Additional Information 3: 58c7 Additional Information 4: 58c75753c6745fad91929ab6430a83fa That's not all that's wrong ('Search' pane has no contents as well, probably more), but it's the most glaring problem. I've seen some allusions to a registry change needed to fix this, but haven't been able to find any details. Anybody? I'm running the latest version of the collection, 1.7.0.6.

  Read the article

• Are these hardwares compatible?

  - by Tom Kaufmann

  I am trying to upgrade my new machine but I want to do it myself. This is my 1st attempt at building system. After carefully reading reviewing feedback and my budget I have decided to select the below listed components. Can anybody let me know are they compatible or not? Transcend 64 GB 2.5" SATA Solid State Drive Asus GeForce GTX550 1GB DDR5 ENGTX550 TI DI/1GD5 Graphics Card Seagate Barracuda 1 TB HDD Internal Hard Drive Cooler Master eXtreme Power Pro 600 Power Supply Intel Core i5 2500K Sandy Bridge 3.30 GHz 95 W 4 Core Desktop Processor Intel DX79TO Motherboard Corsair CMZ8GX3M2A1600C9 8 GB DDR3 SDRAM 1600 MHz Dual Channel Kit Desktop Memory Sony AD-7260S-ZS Internal DVD Writer - Black Cooler Master Hyper TX3 EVO Intel CPU Cooler Cooler Master Elite 335U Cabinet LG E2051T 20.1 Inch SuperSlim Monitor Is any of these hardware components incompatible with I5 2500K? If you have any other suggestions for selecting any other harwdware that can boost up my performance or lower my cost while having the same performance, please suggest. But my primary questions is whether they are compatible or not! Any help is appreciated. Thank you.

  Read the article

• Constant crashes in windows 7 64bit when playing games

  - by yx.

  I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

  Read the article

• How to find out which process is hogging the linux server?

  - by user1149518

  We have a RHEL server. Today it suddenly became slow. Symptoms - It was responding slow to ping queries from other server. When I try to login using ssh, it was taking about 10 seconds to login. I was able to resolve the problem by doing some guess work. I killed one process which I thought was culprit. Which resolved the problem. Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness. These were the conditions when the server was slow - # vmstat 3 3 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 1 176 6730868 285052 4899676 0 0 3 4 0 0 1 1 97 1 0 0 0 176 6751576 285064 4899704 0 0 0 115 15307 37171 1 1 96 3 0 0 0 176 6751948 285068 4899700 0 0 0 23 14813 39559 1 1 98 1 0 # top top - 16:38:18 up 150 days, 19:36, 64 users, load average: 1.68, 1.46, 1.44 Tasks: 1287 total, 2 running, 1284 sleeping, 1 stopped, 0 zombie Cpu(s): 1.3%us, 1.7%sy, 0.1%ni, 95.9%id, 0.7%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 16620824k total, 9867124k used, 6753700k free, 287424k buffers Swap: 8193140k total, 176k used, 8192964k free, 4898996k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 26258 khk 34 19 130m 47m 7088 S 11.2 0.3 385:32.42 edm Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness.

  Read the article

• Windows 7: Dual Monitor Issue

  - by sdoca

  I have a Dell laptop with a docking station and two external monitors hooked up. I'm running Windows 7 64 bit. Originally, the two monitors were the same - Dell 1908FP. I have replaced one of them with an HP LA2405. I have set the HP 24" (1920 x 1200 connected via DVI port) as montior 1 and extended to use the Dell 19" (12080 x 1024 connected via VGA port) as monitor 2. I have set my power plan so that when the laptop is plugged in, it will turn the monitors off after 10 minutes, but it will not put my laptop to sleep. However, now that I have the HP monitor, when I unlock my laptop and the monitors come back on, all my windows are resized and shifted to the top left corner of the HP monitor as if they had been resized for display on the smaller Dell monitor. A co-worker has the exact same laptop and monitor configuration but doesn't experience this issue, so I figure there's some configuration that's different but we can't find it. I haven't been able to find any mention of a similar problem doing an internet search, but I'm not really sure what terms to use in my search. Anybody have any suggestions as to what may be causing the issue? OS setting? Monitor setting? EDIT: My laptop is using the Intel Graphics and Media Control Panel/drivers.

  Read the article

• Windows 7 Laptop Randomly Sleeping

  - by Josh Arenberg

  I'm running Windows 7 64-bit on a Lenovo laptop, and I have a problem wherein after I've put it to 'sleep' once, it will seemingly without any reason or warning go back to sleep every 10 to 15 minutes after that. Each time it wakes back up just fine, and you can happily continue on. However, 10 or 15 minutes later, it just drops out into sleep mode. I don't see any errors in the system logs. I don't think it's related to heat ( since it's not rebooting ). When I check the system event log, I can see where the machine goes to sleep, but it simply says "reason: application API", and doesn't indicate which app ( brilliant ). I don't see any errors from hardware or anything relating to sleep in the application log that would point to what is going on either. How can I find out which app is triggering this? EDIT: I confirmed that temperature wasn't the issue. I think it's important to keep in mind that this condition only happens after the first sleep. If I reboot, the problem goes away until I put it to sleep, after which it sleeps on it's own every few minutes. Is there no way to capture which app is calling the sleep routine?

  Read the article

< Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >