Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 289/1094 | < Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >

• Wireless Connection Troubles

  - by James

  I just recently switched from Windows 7 over to Ubuntu 12.04 and have been experiencing some issues connecting to my home's wireless network. The only way I can get it to connect to the network is by disabling IPv4 and IPv6 settings. Even then while it says its connected to the network (3 bars), I'm unable to access the Internet. It connected for a little while after I first installed Ubuntu, but after the first reboot I haven't been able to access the web at all. I have very basic knowledge when it comes to computers and barely any when dealing with Ubuntu and Linux. I'm very happy with Ubuntu apart from this one issue, as before my computer was overheating and crashing, I've yet to experience any of those problems since installing Ubuntu. The information I can give may be very limited since I'm having to use my cell phone to figure out the solution to this. Any help would be greatly appreciated. Thanks in advance!

  Read the article

• Why can't I ping server? VMware set to 'Bridged' loses IP address

  - by Dave

  I have installed a fresh 10.04 server onto a laptop on a home network as a VMware machine and set network connection to 'Bridged: connect directly to the physical network' from within VMware and rebooted the server. It then loses its IP address. dhclient eth0 says "No working leases in persistent database - sleeping" DHCP is working fine on the wi-fi router. The laptop is wired to a wireless router and from there wirelessly to a desktop. Desktop and Laptop can ping each other from Windows. I can ping the VM from Windows on the same laptop, but not from the desktop. Strangely ping has started to resolve hostnames to IPv6 addresses and not IPv4. Don't know whether that's connected? A kick in the right direction would be greatly appreciated. I've been an Ubuntu desktkop user for a few years, but new to ubuntu servers.

  Read the article

• Issue with setting up multiple IP addresses on ubuntu server installation

  - by varunyellina

  I want to setup two ip addresses on my system for access through lan. This is my config on my other system. Desktop Installation My desktop installation runs with multiple IP's added through networkmanager both through lan and wifi. Server Installation On my server install I've edited /etc/network/interfaces to the following. auto eth0 auto eth0:1 # IP-1 iface eth0 inet static address 172.16.35.35 network 172.16.34.1 netmask 255.255.254.0 broadcast 172.166.35.255 dns-nameservers 172.16.100.221 8.8.8.8 # IP-2 iface eth0:1 inet static address 172.16.34.34 network 172.16.34.1 netmask 255.255.254.0 gateway 172.16.34.1 broadcast 172.16.35.255 After restarting through "/etc/init.d/networking restart" I recieve "Failed to bring up eth0:1" What am I doing wrong? Thankyou.

  Read the article

• No keyring secrets found for [ssid] /802-11-wireless-security, ubuntu 12.04

  - by acimer

  I'm on Ubuntu 12.04 x64bit, installed it couple of days ago. The issue i'm having is this: on startup it connects to my wireless without a problem, but after a while I am disconnected and prompted to enter the key for the wireless network (which is entered - saved) so i just click 'ok', but wireless doesn't connect again. Reseting network manager doesn't help either. Only restart, after which, ubuntu connects to the said wireless without a problem. Terminal outputs this error message: ** Message: No keyring secrets found for cimermanovic /802-11-wireless-security; asking user. cimermanovic is the ssid name. also, here are some error messages that network manager is giving: (nm-applet:31926): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed (nm-applet:31693): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed (nm-applet:30184): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed What should i do to fix this? Thanks!

  Read the article

• All my bandwidth eaten up - report included

  - by Mel

  I have my network bandwidth eaten up totally. Whenever I connect my network, without any application being opened it is always full. I have prepared report of iftop, nethogs and network system monitor. iftop and nethogs My host IP is 192.168.1.203 and all the rest are not known though I have tried to pin 192.168.1.105, it doesn't reply. If possible I would like to block the most disturbing IP which is 192.168.1.105 to block it. but don't know how.

  Read the article

• Other people's files showing up in rhythmbox

  - by Avery Boyer

  I have my computer connected to a college network, and right now files that belong to other individuals on campus are showing up under Shared in rhythmbox. This is driving me up the wall, I absolutely despise the idea that files are being thrown around on the network and that other people's s*** is showing up on my computer, and that they may be able to see my files as well. This is a very, very serious problem as far as I am concerned and I want to know how I can ensure that I am sharing nothing with the network in the way of files on my computer and that no one else's files are showing up on my computer.

  Read the article

• dhcpd fails to start

  - by TECHPREACHER

  I recently installed Ubuntu 11.10 I then used apt-get to grab isc-dhcp3. I removed Network-Manager and manually configured my network interface eth0. In addition, I hand edited a dhcpd.conf file and designated eth0 as the listen port in /etc/default/isc-dhcp-server. However, each time I attempt to start dhcpd it fails. When I view the syslog file, the last line is as follows: "Not configured to listen on any interfaces!" My eth0 interface works fine. I can ping addresses inside and outside the network and perform DNS queries. Any help would be greatly appreciated. AJ

  Read the article

• Share between Ubuntu machines

  - by Anero

  I'm sure it might be a very easy way to do this, but I haven't found how... I have two machines with Ubuntu 10.10 on the same network (just workgroup, no domain involved). On one of them I have shared a folder through Nautilus Folder Sharing. When opening the Network place on the second machine, I cannot see the first one listed, just Windows Network and when going into this folder I can see the Workgroup though when trying to go into it I get an Unable to mount. Failed to retrieve share list from server error. Is it required to do something else when sharing the folder through Nautilus?

  Read the article

• Sharing samba-folder with root access

  - by Industrial

  Hi everyone, I have a staging server in my network running Ubuntu server 10.10, being my main development area. As I need to access the files in the Apache root from other computers in the network, I have setup samba with the following settings: [www] comment = Apache root www path = /var/www writable = yes force user = root force group = root On the host computer, running Ubuntu 10.10 desktop, I am trying to mount the drive with a bash file looking like below: #!/bin/bash sudo mount -t cifs //192.168.1.5/www /media/www/ -o username=myusername,password=mypassword,rw,iocharset=utf8,file_mode=0777,dir_mode=0777 What happens is that I get mount error(13): Permission denied Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) thrown in my face whilst trying to execute the mount. I've done exactly the same, with exactly the same smb.conf & mount-bash file on another computer in my network, but this just wont work. What am I doing wrong? I am running out of ideas.

  Read the article

• VirtualBox: Import on different platform

  - by katsumii

  VirtualBox behaves almost the same on different OSes but the default network name for host-only network is different.The picture below is from Windows. On Linux, it will be named "vboxnet0" by default.This causes a problem on cross-platform export/import and it's already reported.#7067 (VERRINTERNALERROR: Inexistent host networking interface, named 'vboxnet0') – Oracle VM VirtualBoxVERR_INTERNAL_ERROR: Inexistent host networking interface, named 'vboxnet0'There are at least 2 workarounds.Open the imported VM in VBox GUI and pick correct network.Run CUI command like below. This one is for Windows.VBoxManage.exe modifyvm node1_1  --hostonlyadapter1 "VirtualBox Host-Only Ethernet Adapter"

  Read the article

• 12.04 in Virtualbox is keep losing my wireless connection

  - by Derek

  I've Windows 7 as the Host OS, Ubuntu 12.04 as the guest and a Netgear WG111v2 as the USB Wireless device. Its connected to an open Wi-Fi network at work to bypass my works crazy strict filtering, When on the domain. I currently have network eth0 turned off in the virtualbox settings so the only network source would be through the USB device at wlan1. Its odd but the wireless seems extremely temperamental, I constantly have to ifconfig wlan down then ifconfig wlan1 up to get it back online. I know this might be super vague just curious if anyone has tried something like this or run into anything like it to point me in a direction I might not be seeing.

  Read the article

• Passing data between engine layers

  - by spaceOwl

  I am building a software system (game engine with networking support ) that is made up of (roughly) these layers: Game Layer Messaging Layer Networking Layer Game related data is passed to the messaging layer (this could be anything that is game specific), where they are to be converted to network specific messages (which are then serialized to byte arrays). I'm looking for a way to be able to convert "game" data into "network" data, such that no strong coupling between these layers will exist. As it looks now, the Messaging layer sits between both layers (game and network) and "knows" both of them (it contains Converter objects that know how to translate between data objects of both layers back and forth). I am not sure this is the best solution. Is there a good design for passing objects between layers? I'd like to learn more about the different options.

  Read the article

• Cannot get Atheros AR9285 to work on 12.10

  - by user100449

  I've already went through all possible advices and still cannot start my Atheros AR9285 wireless card. I have a laptop Toshiba Portege Z830 where the WiFi already worked under Windows 7. But after migration on Ubuntu 12.10. I'm not able get it work. This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea?

  Read the article

• Battery life starts at 2:30 hrs (99%), but less than 1 minute later is only 1:30 hrs (99%)

  - by zondu

  After searching this and other forums, I haven't seen this same issue listed anywhere for Ubuntu 12. Prior to installing Ubuntu 12.10, my Netbook (Acer AspireOne D250, SATA HDD) was consistently getting 2:30-3 hrs battery life under Windows XP Home, SP3. However, immediately after installing Ubuntu 12.10, the battery life starts out at 2:30 hrs (99%), but less than 1 minute later suddenly drops to 1:30 hrs (99%), which seems very odd. It could be a complete coincidence that the battery is suddenly flaky at the exact same moment that Ubuntu 12.10 was installed, but that doesn't seem likely. I'm a newbie to Ubuntu, so I don't have much experience tweaking/trouble-shooting yet. Here's what I've tried so far: enabled laptop mode (sudo su, then echo 5 /proc/sys/vm/laptop_mode) and checked that it is running when the A/C adapter is unplugged, but it doesn't seem to have made any noticeable difference in battery life, installed Jupiter, but it didn't work and messed up the system, so I had to uninstall it, disabled bluetooth (wifi is still on b/c it is necessary), set the screen to lowest brightness, etc., run through at least 1 full power cycle (running until the netbook shut itself off due to critical battery) and have been using it normally (sometimes plugged in, often unplugged until the battery gets very low) for a week since installing Ubuntu 12.10. installed powertop, but have no idea how to interpret its results. Here are the results of acpi -b: w/ A/C adapter: Battery 0: Full, 100% immediately after unplugging: Battery 0: Discharging, 99%, 02:30:20 remaining 1 minute after unplugging: Battery 0: Discharging, 99%, 01:37:49 remaining 2-3 minutes after unplugging: Battery 0: Discharging, 95%, 01:33:01 remaining 10 minutes after unplugging: Battery 0: Discharging, 85%, 01:13:38 remaining Results of cat /sys/class/power_supply/BAT0/uevent: w/ A/C adapter: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Full POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=12136000 POWER_SUPPLY_CURRENT_NOW=773000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1956000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= immediately after unplugging: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11886000 POWER_SUPPLY_CURRENT_NOW=773000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1937000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 1 minute later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11728000 POWER_SUPPLY_CURRENT_NOW=1174000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1937000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 2-3 minutes later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11583000 POWER_SUPPLY_CURRENT_NOW=1209000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1878000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 10 minutes later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11230000 POWER_SUPPLY_CURRENT_NOW=1239000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1644000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= Results of upower -i /org/freedesktop/UPower/devices/battery_BAT0: w/ A/C adapter: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:24:58 2012 (823 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: fully-charged energy: 21.1248 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 8.3484 W voltage: 12.173 V percentage: 100% capacity: 43.4667% technology: lithium-ion immediately after unplugging: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:41:25 2012 (1 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.9196 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 8.3484 W voltage: 11.86 V time to empty: 2.5 hours percentage: 99.0286% capacity: 43.4667% technology: lithium-ion History (charge): 1354023683 99.029 discharging 1 minute later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:42:31 2012 (17 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.9196 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.5432 W voltage: 11.753 V time to empty: 1.5 hours percentage: 99.0286% capacity: 43.4667% technology: lithium-ion History (charge): 1354023683 99.029 discharging History (rate): 1354023751 13.543 discharging 2-3 minutes later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:45:06 2012 (20 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.2824 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.7484 W voltage: 11.545 V time to empty: 1.5 hours percentage: 96.0123% capacity: 43.4667% technology: lithium-ion History (charge): 1354023906 96.012 discharging 1354023844 97.035 discharging History (rate): 1354023906 13.748 discharging 1354023875 12.992 discharging 1354023844 13.284 discharging 10 minutes later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:54:24 2012 (28 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 18.1764 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.2948 W voltage: 11.268 V time to empty: 1.4 hours percentage: 86.0429% capacity: 43.4667% technology: lithium-ion History (charge): 1354024433 86.043 discharging History (rate): 1354024464 13.295 discharging 1354024433 13.662 discharging 1354024402 13.781 discharging I noticed that between #2 and #3 (0 and 1 minutes after unplugging), while the battery still reports 99% charge and drops from 2:30 hr to 1:30 hr, the energy usage goes from 8.34 W to 13.54 W and the current_now increases, but shouldn't it be using less energy in battery mode since the screen is much dimmer and it's in power saving mode? (or is that normal behavior?) It also seems to drain more quickly than what it predicts, especially with the 1-1.25 hour drop in the first minute of being unplugged, which seems odd. What really concerns me is that Ubuntu 12.10 may not be properly managing the battery (with the sudden change in charge/life from 2:30 to 1:30 or 1:15 within a minute of unplugging), and that a new battery may quickly die under Ubuntu 12.10. I'd greatly appreciate any advice/suggestions on what to do, and especially whether there's a way to get back the 1-1.5 hrs of battery life that were suddenly lost when changing from WinXp to Ubuntu 12.10. Thanks :)

  Read the article

• samba share not allowing windows pc to access

  - by user72289

  I have been trying to no avail, to share folders on my ubuntu pc with a windows network. The windows network isn't a homegroup, just a straight up access to folders made public. I can see the ubuntu shares I make, but when I try to access them I get a permission denied contact your system administrator type message. Could someone clarify the area re adding a user to samba, as there are about 30 different unix usernames! I just want my windows network to have unrestricted access to my linux folders. Any help would be greatly appreciated

  Read the article

• Sidestep Automatically Secures Your Mac’s Connection on Unsecure Networks

  - by Jason Fitzpatrick

  If you’re wary of browsing on wide open public Wi-Fi networks (and you should be), Sidestep is a free Mac application that routes your connection on an unsecure network through a secure proxy. Sidestep automatically detects when you are on an unprotected wireless network and forms an encrypted tunnel to the proxy you specified during setup. Anytime you login a wide open Wi-Fi node (such as at a coffee shop, airport, or other public area) you won’t be broadcasting your login credentials and other personal information in what amounts to plain text into the air around you. Anyone snooping on you or the network in general will simply see your stream of encrypted data going to the proxy. Hit up the link below to grab a copy and read additional information about setting up the program and finding/configuring a proxy server. Sidestep is freeware, Mac OS X only. Sidestep [via Gina Trapani] How to Create an Easy Pixel Art Avatar in Photoshop or GIMPInternet Explorer 9 Released: Here’s What You Need To KnowHTG Explains: How Does Email Work?

  Read the article

• Help me start my Atheros AR9285 working on Ubuntu 12.10

  - by user100449

  Could you, pls, help me with my wireless card Atheros AR9285 on Ubuntu 10.12.. I've already went through all possible advices and still cannot start my wireless card. I have a laptop Toshiba Portege Z830 where Wifi've already worked under Windows 7. But after migration on Ubuntu 10.12. I'm not able get it work. My actual situation is on image bellow This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea? Thank you Michal

  Read the article

• Putting Ubuntu Server on to a networked HDD

  - by SimplySimon

  Firstly, I know very little about servers and secondly the 1Tb HDD I have has network capabilities, but no software is installed on it, so when connected to the computer it is seen as a network connection, but not as a drive. Any advice on how to get started would be great. Up until now, I have been using it as a USB drive which worked well, but when this is sorted, I would like it to be connected directly to our BT HomeHub accessible through the WiFi for all the family to use as a film and back up repository. I would then be able to set up individual accounts for each family member to use and may be, if possible, make it accessible from outside locations. The First question then is: How can I install Ubuntu server on the 1Tb HDD attached directly to the computers network port but which doesn't show up in Nautilus? HDD Western Digital 1.0Tb LBA 1953525168 Model: WD10EACS-00DB0 DCM: DHRNHT2CF

  Read the article

• Wireless/Bluetooth problems on t43p

  - by user75965

  I have been struggling to get my wireless mini pcmcia card recognised by 12.04. It suddenly stopped, mid session. I have taken it out and replaced with a couple of spares with slightly different serial numbers. One had no joy - 'unauathorised'. The other worked briefly for thunderbird but not firefox, it seemed. The network controller reads like this: 0b:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05) I have ordered a replacement from ebay, and hope I got the right one - used the the FRU number from the one that stopped working. But I have ALWAYS had no joy with my Thinkpad t43p Bluetooth and Ubuntu ( 12.04, and even 11.04 and 11.10, if I remember rightly). Do you think the Bluetooth problem will solve with a new mini pcmcia? Surely not, as it has never worked, whereas Wireless worked until a couple of weeks ago...

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• Slow writing HDD speed, Ubuntu 12.04 64-bit, Thinkpad T520i

  - by pyc

  It seems that (but I'm not completely sure), that when I'm copying files from gigabit network to HDD, I can't use full potential of the network which in my case is about 60 MB/s, because HDD writing is so slow like lower than 10 MB/s, and also it's slowing down the whole system which becomes pretty much unresponsive, almost impossible to work with. Copying files to samba share residing at Ubuntu machine, connected to share from Windows 7, I'm completely sure my network equipment is OK, and there's no CPU intensive process on Ubuntu except smbd getting about 10-20% from time to time which I think is OK. Something here is burried deep I think, maybe even in kernel. Already tried to switch from AHCI to compatibility mode, and turning acpi on and off - nothing helped. So it's like HDD buffer is full and emptying slowly while machine is sluggish, load is about 3 to 4. Somebody experienced the similar problems? Some help on troubleshooting process and identifying the cause would be helpful too :) Thanks!

  Read the article

• ubuntu will not connect after restart

  - by nicedoggy

  Firstly, I hope this hasn't been covered elsewhere, I have searched but haven't found this particular problem. I updated to 12.04 a while back and though I now thoroughly regret that decision, I'm able to live with 12.04 and all it's odd little quirks. The one problem that I would like to fix is this. I have a small network, using a router modem which stays on most of the time. If the computer is switched off, when it is switched on again I have to click on "auto Ethernet" in "Network" in order to get on the internet. It then works fine. Previous versions just connected automatically on restart. When 12.04 says it is unable to connect, other computers on the network are able to connect. Thanks for any help.

  Read the article

• Android - Multiplayer Game - Client / Server - Java etc

  - by user1405328

  I must write a multiplayer pong game for the school. Where are thousand of rooms and where two players can go in to a room and play together and collect points. I programmed the Pong game using Java (LibGDX). How can I do the Network part. I searched the web. And I came across Kryonet. Is there something better? What should I google. On the Internet there are a lot of those questions. And no good answers. I hope that this most questions can be answered. If someone has actual Open Source network game links, tutorials, books, network tutorial, etc. All this would help everyone. Thank you.

  Read the article

• USB modem dosn't working in Ubuntu

  - by skeeph

  In Ubuntu 12.10 USB-modem Huawei 171 from MTS is not connected to the network. First on the message "Are you registered on the network", immediately after that, "You are disconnected from the network." This happened after there was an internal error notification Ubuntu. I did not pay attention, and closed by sending the report. After the reboot does not work. Settings are not changed. I am online with this modem in Windows 8. Could you tell me why it is not working,please thank you in advance P.S Sorry for my English. It's foreign language for me. Please mention to me where are my mistakes. Thanks

  Read the article

• Need instructions on how to create wpa_supplicant.conf and add fast_reauth=0 to it

  - by nutty about natty

  Like many other natty users on a university/academic network, I'm experiencing annoying frequent disconnects/hangs/delays. See, for instance here. I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: README You will need to make a configuration file, e.g. /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

  Read the article

< Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >