Search Results

Search found 3140 results on 126 pages for 'debian'.

Page 29/126 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Strange message during the Linux boot and slow start caused by "udevd[336] timeout ... "

  - by Kyrol

  When Debian (wheezy testing version) is loading, at a certain point appears a strange message: udevd[336] timeout usb_id--export /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-2.2/1-1.2:1.0 video4linux/ [502] after this message, start another message that loops for 120 secs: udevd[336] killing /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-2.2/1-1.2:1.0 video4linux/ [502] When the loop finish, Debian start normally and nothing seems to be "broken"! I also killed the loop with CTRL-C to break the loop and the system doesn't give any problem. Does anyone know a possible answer?

  Read the article

• Minimal Lunix distribution with sshd and apt

  - by Sergey Mikhanov

  When I signed up for my Debian Linux VPS hosting and first logged on and invoked ps, there was the only user process running: sshd. As I can see, this was minimal Linux with only two things installed and configured: sshd and apt (plus all dependencies, of course). I want to build (or use existing) similar Linux distro, any advice on how to build (or pick) one? Googling "minimum linux", or "linux with sshd only" usually brings up Debian's netinstall, which is not what I want. Thanks in advance.

  Read the article

• VMWare Server lck file keeps coming back

  - by muncherelli

  I am running VMWare Server 2.0 on a Debian Lenny system as a host OS. I am getting this error when I try to start a Virtual Machine Cannot open the disk '/var/lib/vmware/Virtual Machines//.vmdk' or one of the snapshot disks it depends on. Reason: Failed to lock the file. So I looked around on the web and found that I need to delete the .lck folder and file in order to get this error This seems to happen any time I reboot my Debian Server. The Virtual Machines sometimes do not recover and this lck file is causing problems. Should I create a cron script that does a rm *.lck on each of my machines on reboot? Looking for any direction on how to resolve this. It seems when i do a "reboot" command it is maybe not gracefully shutting down the VMware containers so the lock files are still intact?

  Read the article

• Packaging python software with custom dependencies

  - by viraptor

  Hi, I'm looking for a good way to package a Python application that is going to be deployed on a Debian server. The application itself depends on some modules which are not included in base Debian repository, although they might be in the future. This creates some problems... I depend on some patches to those modules. If the original module gets installed one day, the application will break. However if I install everything I need in a virtualenv just for that application, I lose the ability to upgrade Python itself (in case of security updates). The third option would be to rename my fork of the upstream module and just treat it as a completely separate one. But that would mean changing the code (not much work, but it wouldn't be that clean / universal anymore). Are there any other options that I missed? Are there any pros / cons I didn't see in the solutions above?

  Read the article

• How to configure autofs5 timeout on per-filesystem basis?

  - by Norman Ramsey

  Because of a show-stopping bug in Debian autofs 4, I just upgraded to autofs5. It is not honoring the timeout option in my auto.master file: /var/autofs/removable /etc/auto.removable --timeout=2 I use this map for thumb drives and so on; I don't want a general default timeout of 2 seconds. I did some digging and although the --timeout option worked in autofs 4, and it appears in some examples on the Web, it is not actually sanctioned (or even mentioned) in the documentation for the auto.master file. So I don't feel I can report the problem as a bug. How can I get autofs5 to timeout after 2 seconds only on designated filesystems? Update: I am using a Debian-packaged autofs5, version 5.0.4-3.2.

  Read the article

• Lighttpd with FastCGI won't create /tmp/fcgi.sock on startup?

  - by Marlon

  I'm running lighttpd-1.4.19 on a debian 5 box and try to run web2py with fastcgi. The problem with that is, that lighttpd does not create the socket file /tmp/fcgi.sock. If I'm creating the file by myself touch /tmp/fcgi.sock lighttpd will start but will throw this error after some time running: unexpected end-of-file (perhaps the fastcgi process died): pid: 0 socket: unix:/tmp/fcgi.sock My config looks like this: fastcgi.server = ( "/handler_web2py.fcgi" = ( "handler_web2py" = ( #name for logs "check-local" = "disable", "socket" = "/tmp/fcgi.sock", "idle-timeout" = 20, "max-procs" = 1 ) ), ) Is there any known problem with running lighttpd on debian 5? Thanks for any help. I have pasted the whole lighttpd config: http://pastie.org/1660646

  Read the article

• Development environment for embedded system

  - by Howard Lee Harkness

  I need to develop software in C/C++ for an embedded system. I have Debian 6 running off of a USB hard drive. I would like to be able to generate a stripped-down kernel with modules, and install them either on a CF card or a USB 'thumb' drive. I succeeded in building a Linux 3.6 kernel and running it in Debian off of the USB hard drive, but I am having trouble figuring out how to install it on the thumb drive. I would like a build cycle that looks like this: 1) Build module or kernel with desired software 2) Install it on thumb drive 3) Boot and test I would like to use the same system for both development and testing, if that is feasible. I am looking for resources and tutorials that would help me understand how to do this.

  Read the article

• How to install ia32-libs on Wheezy?

  - by javano

  I have seen a couple of questions on ServerFault relating to installing ia32-libs on a 64bit machine but the solutions aren't working for me (I don't think any of these questions where for Wheezy specifically I'm not sure how to proceed); root@server:/home/# apt-get install -f ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# sudo apt-get install ia32-libs-i386 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs-i386:i386 : Depends: freeglut3:i386 (>= 2.6.0-1) but it is not going to be installed Depends: lesstif2:i386 (>= 1:0.95.2-1) but it is not going to be installed Depends: libacl1:i386 (>= 2.2.49-4) but it is not going to be installed Depends: libasyncns0:i386 (>= 0.3-1.1) but it is not going to be installed Depends: libattr1:i386 (>= 1:2.4.44-2) but it is not going to be installed Depends: libaudio2:i386 (>= 1.9.2-4) but it is not going to be installed Depends: libaudiofile1:i386 (>= 0.2.6-8) but it is not going to be installed Depends: libavahi-client3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libavahi-common3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libbsd0:i386 (>= 0.2.0-1) but it is not going to be installed Depends: libcap2:i386 (>= 1:2.19-3) but it is not going to be installed Depends: libcomerr2:i386 (>= 1.41.12-4stable1) but it is not going to be installed Depends: libcups2:i386 (>= 1.4.4-7+squeeze1) but it is not going to be installed Depends: libcurl3:i386 (>= 7.21.0-2) but it is not going to be installed Depends: libdbus-1-3:i386 (>= 1.2.24-4+squeeze1) but it is not going to be installed Depends: libdirectfb-1.2-9:i386 (>= 1.2.10.0-4) but it is not going to be installed Depends: libdrm-intel1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm-radeon1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm2:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libedit2:i386 (>= 2.11-20080614-2) but it is not going to be installed Depends: libesd0:i386 (>= 0.2.41-8) but it is not going to be installed Depends: libexif12:i386 (>= 0.6.19-1) but it is not going to be installed Depends: libexpat1:i386 (>= 2.0.1-7) but it is not going to be installed Depends: libflac8:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libfltk1.1:i386 (>= 1.1.10-2+b1) but it is not going to be installed Depends: libfontconfig1:i386 (>= 2.8.0-2.1) but it is not going to be installed Depends: libfreetype6:i386 (>= 2.4.2-2.1+squeeze3) but it is not going to be installed Depends: libgcrypt11:i386 (>= 1.4.5-2) but it is not going to be installed Depends: libgdbm3:i386 (>= 1.8.3-9) but it is not going to be installed Depends: libgl1-mesa-dri:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgl1-mesa-glx:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libglu1-mesa:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgnutls26:i386 (>= 2.8.6-1) but it is not going to be installed Depends: libgpg-error0:i386 (>= 1.6-1) but it is not going to be installed Depends: libgphoto2-2:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgphoto2-port0:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgssapi-krb5-2:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libice6:i386 (>= 2:1.0.6-2) but it is not going to be installed Depends: libidn11:i386 (>= 1.15-2) but it is not going to be installed Depends: libieee1284-3:i386 (>= 0.2.11-6) but it is not going to be installed Depends: libjack-jackd2-0:i386 (>= 1.9.5~dfsg-14) but it is not going to be installed or libjack0:i386 (>= 1:0.118+svn3796-7) but it is not going to be installed Depends: libjpeg62:i386 (>= 6b1-1) but it is not going to be installed Depends: libjpeg8:i386 (>= 8b-1) but it is not going to be installed Depends: libk5crypto3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkeyutils1:i386 (>= 1.4-1) but it is not going to be installed Depends: libkrb5-3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkrb5support0:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: liblcms1:i386 (>= 1.18.dfsg-1.2+b3) but it is not going to be installed Depends: libltdl7:i386 (>= 2.2.6b-2) but it is not going to be installed Depends: liblzo2-2:i386 (>= 2.03-2) but it is not going to be installed Depends: libmpg123-0:i386 (>= 1.12.1-3) but it is not going to be installed Depends: libnspr4-0d:i386 (>= 4.8.6-1) but it is not going to be installed Depends: libnss3-1d:i386 (>= 3.12.8-1+squeeze4) but it is not going to be installed Depends: libogg0:i386 (>= 1.2.0~dfsg-1) but it is not going to be installed Depends: libopenal1:i386 (>= 1:1.12.854-2) but it is not going to be installed Depends: libpam0g:i386 (>= 1.1.1-6.1+squeeze1) but it is not going to be installed Depends: libpng12-0:i386 (>= 1.2.44-1+squeeze1) but it is not going to be installed Depends: libpopt0:i386 (>= 1.16-1) but it is not going to be installed Depends: libpulse0:i386 (>= 0.9.21-3+squeeze1) but it is not going to be installed Depends: libsamplerate0:i386 (>= 0.1.7-3) but it is not going to be installed Depends: libsane:i386 (>= 1.0.21-9) but it is not going to be installed Depends: libsasl2-2:i386 (>= 2.1.23.dfsg1-7) but it is not going to be installed Depends: libsdl1.2debian:i386 (>= 1.2.15) but it is not going to be installed Depends: libselinux1:i386 (>= 2.0.96-1) but it is not going to be installed Depends: libsigc++-2.0-0c2a:i386 (>= 2.2.4.2-1) but it is not going to be installed Depends: libsm6:i386 (>= 2:1.1.1-1) but it is not going to be installed Depends: libsndfile1:i386 (>= 1.0.21-3+squeeze1) but it is not going to be installed Depends: libsqlite3-0:i386 (>= 3.7.3-1) but it is not going to be installed Depends: libssh2-1:i386 (>= 1.2.6-1) but it is not going to be installed Depends: libssl1.0.0:i386 (>= 1) but it is not going to be installed Depends: libstdc++5:i386 (>= 1:3.3.6-20) but it is not going to be installed Depends: libsvga1:i386 (>= 1:1.4.3-29) but it is not going to be installed Depends: libsysfs2:i386 (>= 2.1.0+repack-1) but it is not going to be installed Depends: libtasn1-3:i386 (>= 2.7-1) but it is not going to be installed Depends: libtdb1:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libtiff4:i386 (>= 3.9.4-5+squeeze3) but it is not going to be installed Depends: libts-0.0-0:i386 (>= 1.0-7) but it is not going to be installed Depends: libusb-0.1-4:i386 (>= 2:0.1.12-16) but it is not going to be installed Depends: libuuid1:i386 (>= 2.17.2-9) but it is not going to be installed Depends: libvorbis0a:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisenc2:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisfile3:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libwrap0:i386 (>= 7.6.q-19) but it is not going to be installed Depends: libx11-6:i386 (>= 2:1.3.3-4) but it is not going to be installed Depends: libx86-1:i386 (>= 1.1+ds1-6) but it is not going to be installed Depends: libxau6:i386 (>= 1:1.0.6-1) but it is not going to be installed Depends: libxaw7:i386 (>= 2:1.0.7-1) but it is not going to be installed Depends: libxcb-render-util0:i386 (>= 0.3.6-1) but it is not going to be installed Depends: libxcb-render0:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcb1:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcomposite1:i386 (>= 1:0.4.2-1) but it is not going to be installed Depends: libxcursor1:i386 (>= 1:1.1.10-2) but it is not going to be installed Depends: libxdamage1:i386 (>= 1:1.1.3-1) but it is not going to be installed Depends: libxdmcp6:i386 (>= 1:1.0.3-2) but it is not going to be installed Depends: libxext6:i386 (>= 2:1.1.2-1) but it is not going to be installed Depends: libxfixes3:i386 (>= 1:4.0.5-1) but it is not going to be installed Depends: libxft2:i386 (>= 2.1.14-2) but it is not going to be installed Depends: libxi6:i386 (>= 2:1.3-6) but it is not going to be installed Depends: libxinerama1:i386 (>= 2:1.1-3) but it is not going to be installed Depends: libxml2:i386 (>= 2.7.8.dfsg-2+squeeze1) but it is not going to be installed Depends: libxmu6:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxmuu1:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxp6:i386 (>= 1:1.0.0.xsf1-2) but it is not going to be installed Depends: libxpm4:i386 (>= 1:3.5.8-1) but it is not going to be installed Depends: libxrandr2:i386 (>= 2:1.3.0-3) but it is not going to be installed Depends: libxrender1:i386 (>= 1:0.9.6-1) but it is not going to be installed Depends: libxslt1.1:i386 (>= 1.1.26-6) but it is not going to be installed Depends: libxss1:i386 (>= 1:1.2.0-2) but it is not going to be installed Depends: libxt6:i386 (>= 1:1.0.7-1) but it is not going to be installed Depends: libxtst6:i386 (>= 2:1.1.0-3) but it is not going to be installed Depends: libxv1:i386 (>= 2:1.0.5-1) but it is not going to be installed Depends: libxxf86vm1:i386 (>= 1:1.1.0-2) but it is not going to be installed Depends: odbcinst1debian2:i386 (>= 2.2.14p2-1) but it is not going to be installed Depends: libodbc1:i386 but it is not going to be installed Depends: xaw3dg:i386 (>= 1.5+E-18) but it is not going to be installed php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# dpkg --print-architecture amd64 root@server:/home/# dpkg --print-foreign-architectures i386 root@server:/home/# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 7.1 (wheezy) Release: 7.1 Codename: wheezy root@server:/home/# uname -a Linux servername 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux root@server:/home/# cat /etc/apt/sources.list deb http://ftp.us.debian.org/debian stable main contrib non-free

  Read the article

• Grub: Legacy 'ask' parameter no longer supported

  - by leeand00

  I'm trying to change the resolution on my base shell (the Ctrl+Alt+1) shell in Debian so that it supports my ViewSonic monitor. The shell appears really fuzzy when it is displayed on my lcd monitor, but GRUB looks fine when it's displayed. In I tried changing part of the GRUB_CMDLINE_LINUX_DEFAULT to 'vga=ask', and now I get the error on booting up 'Legacy 'ask' parameter no longer supported' Has this 'vga=ask' value been changed to something else? Note, I tried setting it to 'vga=782' after finding a list of screen modes here and the shell font got real huge for a few seconds during boot up, and then switched back to it's awful fuzzy self again, when I went to use the Debian Bash shell. UPDATE Tried suggestion in this question, it works without fuzziness until the last resolution change which displays the user login to the shell.

  Read the article

• www-data is unable to write to an NFS share

  - by Bastian

  On Debian Squeeze, I created an NFS share with these options rw,sync,no_root_squash,no_subtree_check,insecure and on the other Debian Squeeze I can successfully mount it and read write with root, but this share is intended to be used by Apache. I changed the permission to 777 just to make sure. And still, the www-data user can read, create files but not write to them! It does not sound to me like the typical permissions problem, maybe something related to NFS, a lock problem that I am not aware of. Any idea is welcome.

  Read the article

• Ways to remotely reboot a Linux system

  - by dualed

  I had a remote server running Debian Sarge that experienced some HDD failure and I meant to reboot it hoping that fsck could repair the errors automatically. I eventually drove out there and replaced the faulty disks... But I was wondering: What other ways are there to force a Linux system to reboot that do not require hard drive access? What I had tried: shutdown -r now Did not work, as shutdown is a program that would have to be loaded from disk, the error shown in the terminal was bash: /sbin/shutdown: Input/output error init 6 same as above telinit q same as above kill -2 1 This did not print an error, but did not work either. (However, it is possible that the Sarge init did not implement SIGINT, the sarge manpages did not mention it. So it could work in a more recent version of Debian) This guide on PCFreak.net. However, this failed at sysctl, which was not in memory either.

  Read the article

• Minimal Linux distribution with sshd and apt

  - by Sergey Mikhanov

  When I signed up for my Debian Linux VPS hosting and first logged on and invoked ps, there was the only user process running: sshd. As I can see, this was minimal Linux with only two things installed and configured: sshd and apt (plus all dependencies, of course). I want to build (or use existing) similar Linux distro, any advice on how to build (or pick) one? Googling "minimum linux", or "linux with sshd only" usually brings up Debian's netinstall, which is not what I want. Thanks in advance.

  Read the article

• How to reduce 3rd party repository priority in apt

  - by carlosz

  I'm using Debian Testing together with the Deb Multimedia (previously Debian Multimedia) repository for testing. I want to reduce the priority of the deb-multimedia packages so it only installs certain packages. I've tried with: Package: * Pin: release o="Unofficial Multimedia Packages" Pin-Priority: 10 and Package: * Pin: origin "mirror.home-dn.net" Pin-Priority: 10 But neither works, the packages still have the default priority (500). The Release file from the repository looks like this: Archive: testing Version: None Component: main Origin: Unofficial Multimedia Packages Label: Unofficial Multimedia Packages Architecture: amd64 What am I doing wrong? Edit: It worked when I used the Version information instead: Package: * Pin: release v=None Pin-Priority: 10 But I still don't know the reason the other filters didn't work.

  Read the article

• Share folder with active directory group permissions

  - by Hihui

  I have a Debian as a member of our AD (which is a 2k3). I want to share 2 folders from our Debian. 1 with full access for everyone, the second only readable by group "ADM", and "PROD". Part of smb.conf: [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL netbios name = SERV-FTP wins server = "IP serv 2k3" security = domain [JUKEBOX] // full access path = /media/JUKEBOX/JUKEBOX comment = sharing writable = yes browsable = yes public = yes read only = no valid users = @ASYLUM\prod_std admin users = @ASYLUM\ADM [SOFTWARE] comment = Software path = /media/JUKEBOX/SOFTWARE valid users = @ASYLUM\prod_adv, @ASYLUM\ADM writable = yes read only = no My log : [2013/10/25 09:24:37.316643, 0] smbd/service.c:1055(make_connection_snum) canonicalize_connect_path failed for service SOFTWARE, path /media/JUKEBOX/SOFTWARE And, from my Windows's client, if i want to access on that folder : Windows can't access to \serv-ftp\software Where is the problem ... ? Thx !

  Read the article

• Debian 7 and PHP 5.4.4 error reporting

  - by milovan

  I use default php.ini and then in my PHP script (local.settings.php in Drupal) I simply set ini_set('error_reporting', 'E_ALL & ~E_NOTICE & ~E_STRICT'); According to documentation this means "show all messages minus notice and strict warnings". But in my case it still shows strict warnings! I have no idea why, because I clearly stated "~E_STRICT". If I comment it out then I see strict warnings. So it means that default from php.ini "E_ALL & ~E_DEPRECATED & ~E_STRICT" didn't do its job as it also has "~E_STRICT" but I still see strict warnings. On Debian 6 there was Suhoshin patch which was controlling usage of php_ini in PHP scripts. Especially when you try to get more memory than defined cap. Now on debian 7 there is no Suhoshin nor any other security element that might control php_ini. So what might cause php_ini not to be executed? Is there some new variable / setup / other that needs to be checked?

  Read the article

• Linux router: ping doesn't route back

  - by El Barto

  I have a Debian box which I'm trying to set up as a router and an Ubuntu box which I'm using as a client. My problem is that when the Ubuntu client tries to ping a server on the Internet, all the packets are lost (though, as you can see below, they seem to go to the server and back without problem). I'm doing this in the Ubuntu Box: # ping -I eth1 my.remote-server.com PING my.remote-server.com (X.X.X.X) from 10.1.1.12 eth1: 56(84) bytes of data. ^C --- my.remote-server.com ping statistics --- 13 packets transmitted, 0 received, 100% packet loss, time 12094ms (I changed the name and IP of the remote server for privacy). From the Debian Router I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 7, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 8, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 8, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 9, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 9, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 10, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 10, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 11, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 11, length 64 ^C 9 packets captured 9 packets received by filter 0 packets dropped by kernel # tcpdump -i eth2 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 213, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 213, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 214, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 214, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 215, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 215, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 216, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 216, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 217, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 217, length 64 ^C 10 packets captured 10 packets received by filter 0 packets dropped by kernel And at the remote server I see this: # tcpdump -i eth0 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 1, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 1, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 2, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 2, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 3, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 3, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 4, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 4, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 5, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 5, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 6, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 6, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 7, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 7, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 8, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 8, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 9, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 9, length 64 18 packets captured 228 packets received by filter 92 packets dropped by kernel Here "X.X.X.X" is my remote server's IP and "Y.Y.Y.Y" is my local network's public IP. So, what I understand is that the ping packets are coming out of the Ubuntu box (10.1.1.12), to the router (10.1.1.1), from there to the next router (192.168.1.1) and reaching the remote server (X.X.X.X). Then they come back all the way to the Debian router, but they never reach the Ubuntu box back. What am I missing? Here's the Debian router setup: # ifconfig eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:105761 errors:0 dropped:0 overruns:0 frame:0 TX packets:48944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:40298768 (38.4 MiB) TX bytes:44831595 (42.7 MiB) Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38335992 errors:0 dropped:0 overruns:0 frame:0 TX packets:37097705 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:4260680226 (3.9 GiB) TX bytes:3759806551 (3.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3408 errors:0 dropped:0 overruns:0 frame:0 TX packets:3408 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:358445 (350.0 KiB) TX bytes:358445 (350.0 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:2767779 errors:0 dropped:0 overruns:0 frame:0 TX packets:1569477 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3609469393 (3.3 GiB) TX bytes:96113978 (91.6 MiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Ubuntu box (on 10.1.1.12 and 192.168.1.12) Address HWtype HWaddress Flags Mask Iface 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.102 ether NN:NN:NN:NN:NN:NN C eth2 10.1.1.12 ether 00:1e:67:15:2b:f0 C eth1 192.168.1.86 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.2 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.40 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.12 ether 00:1e:67:15:2b:f1 C eth2 192.168.1.77 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.41 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.123 ether NN:NN:NN:NN:NN:NN C eth2 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 10.1.1.0/24 !10.1.1.0/24 MASQUERADE all -- !10.1.1.0/24 10.1.1.0/24 Chain OUTPUT (policy ACCEPT) target prot opt source destination And here's the Ubuntu box: # ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f1 inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28785139 errors:0 dropped:0 overruns:0 frame:0 TX packets:19050735 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32068182803 (32.0 GB) TX bytes:6061333280 (6.0 GB) Interrupt:16 Memory:b1a00000-b1a20000 eth1 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f0 inet addr:10.1.1.12 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:285086 errors:0 dropped:0 overruns:0 frame:0 TX packets:12719 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30817249 (30.8 MB) TX bytes:2153228 (2.1 MB) Interrupt:16 Memory:b1900000-b1920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:86048 errors:0 dropped:0 overruns:0 frame:0 TX packets:86048 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11426538 (11.4 MB) TX bytes:11426538 (11.4 MB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.1.1 0.0.0.0 UG 100 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.8.0.0 192.168.1.10 255.255.255.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Debian box (on 10.1.1.1 and 192.168.1.10) Address HWtype HWaddress Flags Mask Iface 192.168.1.70 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.97 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.103 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.13 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.120 (incomplete) eth0 192.168.1.111 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.51 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.102 (incomplete) eth0 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.74 (incomplete) eth0 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.121 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.71 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.88 (incomplete) eth0 192.168.1.82 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.98 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.73 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.11 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.85 (incomplete) eth0 192.168.1.112 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.81 ether NN:NN:NN:NN:NN:NN C eth0 10.1.1.1 ether 94:0c:6d:82:0d:98 C eth1 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.10 ether 6c:f0:49:a4:47:38 C eth0 192.168.1.86 (incomplete) eth0 192.168.1.119 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth1 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth0 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination Edit: Following Patrick's suggestion, I did a tcpdump con the Ubuntu box and I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 1, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 1, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 2, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 2, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 3, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 3, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 4, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 4, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 5, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 5, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 6, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 6, length 64 ^C 12 packets captured 12 packets received by filter 0 packets dropped by kernel So the question is: if all packets seem to be coming and going, why does ping report 100% packet loss?

  Read the article

• Wget works, Ping doesn't

  - by derty

  There are some anomalies on a Virtuozzo virtualized Debian 4 (I know, I'm gonna upgrade this one asap, but there dependences). We run some Websites on this one. And a view Days ago exmi4 wasnt able to send mails to SOME people. I'll use live.com as exampledomain! So some of this people got mails and some didn't. Some of the mails got stuck in the queue, and after 2 days they went out!! My Nagios never showed problems with the internet connection or disk space Now i wanted to install "dig" to look how he's solving the dns request. And this Debian tells me he doesn't know dig.. Long story made short, Debian is able to download sites with exact IP or even with wget live.com, but it is not able to ping live.com. I'm 99% sure that the networking is right and the routing too! Some examples of my tring below: wget live.com downloads the site ping live.com ping http://www.live.com ping http://live.com returns: ping: unknown host live.com EDIT: i now use heise.de not live.com any more. and i found out i can ping the heise.de server by using it's IP-address. myserver:~# ping 193.99.144.85 PING 193.99.144.85 (193.99.144.85) 56(84) bytes of data. 64 bytes from 193.99.144.85: icmp_seq=1 ttl=248 time=12.7 ms 64 bytes from 193.99.144.85: icmp_seq=2 ttl=248 time=12.6 ms 64 bytes from 193.99.144.85: icmp_seq=3 ttl=248 time=12.9 ms 64 bytes from 193.99.144.85: icmp_seq=4 ttl=248 time=13.1 ms 64 bytes from 193.99.144.85: icmp_seq=5 ttl=248 time=13.1 ms --- 193.99.144.85 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4001ms rtt min/avg/max/mdev = 12.671/12.924/13.163/0.238 ms EDIT 2: myserver:/etc/apt# dig heise.de ; <<>> DiG 9.3.4-P1.2 <<>> heise.de ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 40551 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 5, ADDITIONAL: 3 ;; QUESTION SECTION: ;heise.de. IN A ;; ANSWER SECTION: heise.de. 2266 IN A 193.99.144.80 ;; AUTHORITY SECTION: heise.de. 1622 IN NS ns.pop-hannover.de. heise.de. 1622 IN NS ns.s.plusline.de. heise.de. 1622 IN NS ns.plusline.de. heise.de. 1622 IN NS ns2.pop-hannover.net. heise.de. 1622 IN NS ns.heise.de. ;; ADDITIONAL SECTION: ns.plusline.de. 265 IN A 212.19.48.14 ns.pop-hannover.de. 5113 IN A 193.98.1.200 ns2.pop-hannover.net. 15150 IN A 62.48.67.66 ;; Query time: 2 msec ;; SERVER: 193.200.112.80#53(193.200.112.80) ;; WHEN: Tue Oct 9 13:03:50 2012 ;; MSG SIZE rcvd: 216

  Read the article

• Remote Scripted Installation of Sun/Oracle JRE

  - by chrisbunney

  I'm attempting to automate the installation of a Debian server (debian 6.0 squeeze 64bit). Part of the installation requires the Sun JRE package to be installed. This package has a licence agreement, which has to be accepted. I have a script which uses the following lines to accept and install the JRE: echo "sun-java6-bin shared/accepted-sun-dlj-v1-1 boolean true" | debconf-set-selections apt-get install -y sun-java6-jre This works fine when executing the script locally. However, I need to execute the script remotely using the ssh command, e.g.: ssh -i keyFile root@hostname './myScript' This doesn't work. In particular, it fails on apt-get install -y sun-java6-jre. It would seem that in spite of me setting the licence agreement to accepted, when run remotely in this manner it is ignored. Despite setting the value to true, I still get prompted to manually accept the agreement when I run this command: ssh -i keyFile root@hostname 'apt-get install -y sun-java6-jre' I suspect it is something to do with environment that is taken care of when running a proper terminal session, but have no idea what to try next to fix it. So, what do I have to do to get this command (and hence my deployment script) to run correctly when executing it remotely? Or is there an alternative way that allows me to install the JRE remotely by another means? Edit 0: I have compared the output of env when executed remotely via ssh and when executed via a local terminal session. The only difference between the outputs is that the local terminal session has the additional value TERM=xterm.

  Read the article

• redmine gives 404 error after installation

  - by Sankaranand

  I am using Debian squeeze with nginx and mysql. After raking db and loading default data to redmine. When i try to visit redmine in a browser, http://ipaddress:8080/redmine, I get a 404 error Page not found The page you were trying to access doesn't exist or has been removed. My nginx configuration file, below: server { listen 8080; server_name localhost; server_name_in_redirect off; #charset koi8-r; #access_log logs/host.access.log main; location / { root html; index index.html index.htm index.php; } location ^~/phpmyadmin/ { root /usr/share/phpmyadmin; index index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/$fastcgi_script_name; } location /redmine/ { root /usr/local/lib/redmine-1.2/public; access_log /usr/local/lib/redmine-1.2/log/access.log; error_log /usr/local/lib/redmine-1.2/log/error.log; passenger_enabled on; allow all; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www$fastcgi_script_name; include fastcgi_params; } location /phpMyadmin { rewrite ^/* /phpmyadmin last; } I don't know what the problem is - this is my second attempt to install redmine in Debian with nginx.

  Read the article

• .htaccess error "not allowed here" for all for all instructions

  - by andres descalzo

  I am using Debian Lenny and Apache 2. I changed the default .htaccess file with: AllowOverride AuthConfig But I always get the error message not allowed here when putting any instructions in the .htaccess file. EDIT: file default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks Order allow,deny Allow from all AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks Includes #AllowOverride All #AllowOverride Indexes AuthConfig Limit FileInfo AllowOverride AuthConfig Order allow,deny Allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> .htaccess: #Options +FollowSymlinks # Prevent Directoy listing Options -Indexes # Prevent Direct Access to files <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> # SEO URL Settings RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] PHP info: apache2handler Apache Version = Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch Apache API Version = 20051115 Server Administrator = webmaster@localhost Hostname:Port = hw-linux.homework:80 User/Group = www-data(33)/33 Max Requests = Per Child: 0 - Keep Alive: on - Max Per Connection: 100 Timeouts = Connection: 300 - Keep-Alive: 15 Virtual Server = Yes Server Root = /etc/apache2 Loaded Modules = core mod_log_config mod_logio prefork http_core mod_so mod_alias mod_auth_basic mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_cgi mod_deflate mod_dir mod_env mod_mime mod_negotiation mod_php5 mod_rewrite mod_setenvif mod_status

  Read the article

• Configuring apache and php to handle many connections

  - by Marc

  My preliminary setup is like this. Two QuadCore 8GB servers running debian 6, with php and apache, One QuadCore 16GB server running debian 6, with mysql My plan is to have one 8Gb server to act as a proxy server, using vertx java to handle connections. I will let vertx use HttpClient to send web requests to the second 8GB server. This would have apache installed and use php to deliver any information that it gets from the mysql server on the third, 16GB server. The main reason I want this setup is to have things separated, so the "proxy" will be the only way to access the system, as the other two server will only be reachable from the local network. I can have the vertx proxy handle 5000+ concurrent connections, but, I don't know how to configure apache to handle all the requests coming from the proxy. Php will connect over mysqli with persistent connection pool of 500-800 connections, the mysql server seems not to have any issues on this part. In previous projects, the apache part was always causing issues, no matter how I set it up. I might not fully understand how to setup apache, since normally apache should handle many concurrent connections, but it does seem to now.

  Read the article

• MySQL Server Is Slow

  - by user2853965746

  I have two MySQL servers and one was just recently setup. The one I just recently setup is a bit slower than my older one, which kind of bothers me because I don't want my clients to be upset with the speed difference when I launch the new one. The older server runs on Ubuntu (~13.04 I believe) and the new one is on Debian 6. Both servers are 2GB ram, but my newer server is has an SSD, so I thought it might be the same speed if not faster. Anyway, the speed difference isn't too much (both are still under a second, but still noticeable). Whenever I select 50 rows from the user table on my older server (SELECT * FROM users LIMIT 50), I get the results in 0.003 s. There is 100,000+ accounts in that table. Whenever running the same command on the same table with only six dev accounts, it takes 0.069 s. It may not seem like a lot, but it's noticeable when you're used to a fast response. I added skip-name-resolve to the config and it didn't seem to help. Basically I'm asking if anyone knows what can cause a MySQL server to be slow in Debian 6? Should I just drop it and switch to Ubuntu like the older server (I don't think the OS is the problem, but you never know)? The older server is under a lot of use too, it's used a lot for web api's on my website. A lot of connections and stuff, and it still remains fast.

  Read the article

• Repository bugzilla package changed to bugzilla3 in Lenny; upgradable?

  - by Pukku

  This question was asked in debianhelp.org almost half a year ago, but never got an answer. I wasn't the one who posted it, however I was today facing exactly the same question. Not sure if copying it to here as such is considered as inappropriate or something, but there's not really anything that I would even like to paraphrase... So let's just go. (I'm sure you will be happy to close it, if this is not the way to go :) Hello all! We are using a Bugzilla server install on a Debian 4/Etch server and are starting to look at the upgrade to Debian 5/Lenny. I was hoping to upgrade the existing Bugzilla server and database from the oldstable (v2.22) to the newer stable in Lenny (v3) when we get to doing a dist-upgrade. However from testing in a virtual machine it seems that the old package was called "Bugzilla" whereas the Lenny package is called "Bugzilla3" and I could not figure a way to directly upgrade between the two. Is it possible to establish some kind of upgrade path quickly after the dist-upgrade to minimise downtime using apt-get or aptitude? Going on past experiences I would not want to do a fresh install with the Bugzilla3 package and attempt to inject the old database into it (previous attempts failed miserably!) :(

  Read the article

• Can't make Dovecot communicate with Postfix using SASL (warning: SASL: Connect to private/auth failed: No such file or directory)

  - by Fred Rocha

  Solved. I will leave this as a reference to other people, as I have seen this error reported often enough on line. I had to change the path smtpd_sasl_path = private/auth in my /etc/postfix/main.cf to relative, instead of absolute. This is because in Debian Postfix runs chrooted (and how does this affect the path structure?! Anyone?) -- I am trying to get Dovecot to communicate with Postfix for SMTP support via SASL. the master plan is to be able to host multiple e-mail accounts on my (Debian Lenny 64 bits) server, using virtual users. Whenever I test my current configuration, by running telnet server-IP smtp I get the following error on mail.log warning: SASL: Connect to /var/spool/postfix/private/auth failed: No such file or directory Now, Dovecot is supposed to create the auth socket file, yet it doesn't. I have given the right privileges to the directory private, and even tried creating a auth file manually. The output of postconf -a is cyrus dovecot Am I correct in assuming from this that the package was compiled with SASL support? My dovecot.conf also holds client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } I have tried every solution out there, and am pretty much desperate after a full day of struggling with the issue. Can anybody help me, pretty please?

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >