Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 29/59 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Problems with wired ethernet connection Ubuntu 11.10

  - by Andrew Fielden

  After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

  Read the article

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Set up a GUI managed firewall for other machines?

  - by Azendale

  What ways are there of setting up a firewall for traffic routed for other machines whose rules can be managed by a GUI? Can GUFW do it? FireStarter? (or should that be avoided because it is supposedly no longer updated?) *By filtering, I'm mean the traffic I am setting rules up for is not destined for this computer. It is either from or to other computers on my LAN. Say, for (a simplified, hypothetical) example: I have an ethernet connection at my dorm that I have plugged into eth0. It gets an address of 192.168.1.185 and I also have 192.168.185.0/24 routed to me, so I don't have to do any NAT. I have a hub attached to my second ethernet port (eth1) with a few Windows computers and I give addresses out of my 192.168.185.0/24 block with DHCP. How can I use my Ubuntu box to block incoming connections from eth0 that are being routed to my Windows computers and let through just a few specific ports (so fellow students can't see what files my Windows boxes are sharing via SMB)?

  Read the article

• ubuntu nic card issue

  - by Blainer

  I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

  - by Lorenzo

  I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• How do I install Intel ethernet drivers?

  - by Pat

  I just bought a Lenovo T420, I booted the live CD and couldn't connect to my wireless router so I figured I needed the drivers for it. I have the last version of Ubuntu(12.04). It's a Intel® 82579 Gigabit Ethernet Controller So I went on intel's website and downloaded the Drivers for Linux and compiled them with make install. Here's the tutorial I followed: Linux Driver Install I have a few question though, What are these doing : modprobe e1000e ifconfig eth0 up dhclient eth0 ping intel.com As far as what I've read, modprobe seems to add the driver to the list of drivers for the kernel, but is that operation only good for one session? The two other lines, I don't understand either what they are doing. What does he mean at the end when he mentions : Note: Whenever the kernel version is upgraded you will need rebuild this driver. And are these steps permanent? Or do I have to add them to some boot.conf file for everytime I boot. Anyways, the steps worked for me and I have established a connection with my router, I just need to know if I need to do additional steps to keep the driver permanently etc.

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• Ubuntu Wireless not working on Lenovo t400

  - by VmaxBoss

  This problem started after upgrading to 12.04, an my system is 'up2date' Have tried most of the solution-proposals found on the net. lspci -nnk | grep -iA2 net 00:19.0 Ethernet controller [0200]: Intel Corporation 82567LF Gigabit Network Connection [8086:10bf] (rev 03) Subsystem: Lenovo Device [17aa:20ee] Kernel driver in use: e1000e 03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlagn iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off sudo lshw -C network *-network description: Ethernet interface product: 82567LF Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:22:68:1a:c4:75 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-3 ip=192.168.2.154 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:29 memory:fc000000-fc01ffff memory:fc024000-fc024fff ioport:1820(size=32) *-network DISABLED description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:6c:2d:24 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:30 memory:f4300000-f4301fff Please help Br/VB

  Read the article

• Setting up a network between a host and guest virtual machine

  - by anonymous

  (I'm running ubuntu server 12.04 on virtual box) I'm trying to transfer a file (scp) from my laptop to one of the directories of a virtual machine. I tried sharing folders, but that failed. I'm a bit of a networking newbie. I've looked at like 20-30 pages. Here's one: http://www.howtoforge.com/moving-files-between-linux-systems-with-scp I followed those steps exactly. My problem is that when I try using scp, it just hangs. I'm also not sure which network interface to configure (eth0, eth1?) in the guest OS. Another (significant?) detail is that the inet address of eth0 is 10.0.2.15 instead of something like 192.168.x.y. I've enabled the bridge adapter and the host-only adapter. Both the laptop and guest VM have openssh-server installed. I'm not sure what to do at this point. Is there a better place to ask about this?

  Read the article

• Configuring network to set wlan0 as primary

  - by Sheed

  I recently had to rebuild my pc and decided to go for ubuntu 14.04. I think the mistake I made was I started from a 12.04 install disk instead of the 12.10 disk I'd used previously and when given the option set my primary connection as ethernet (because the wireless option didn't work). After upgrading to 14.04 etc, I managed to get the wireless working, or more using steps like ifconfig -a and the likes I managed to prove that the wireless card etc. is all installed and working. However every time I boot without a hard wired connection plugged in I get the message "waiting for network configuration". I can then once it's booted without a network get my wirless working using sudo ifconfig wlan0 up iwlist wlan0 scan This seems to kick the wireless module into life and it appears in the GUI and I can then select a network, however all the options like edit network and disconnect etc are all greyed out. What I would like of course is if the WLAN0 was just set as my primary default network so I've been looking for a solution to this and it would seem that I need to adjust the old /etc/network/interfaces file but when I try to do so using the sudo vi /etc/network/interfaces command I, well I simply have no idea what I'm doing. Other than that typing :q! gets me out of there before I do to much damage! As far as I can tell (by navigating to the file in the GUI) the output of my /etc/network/interfaces is as follows: (obviously not including the " in each line that's just to break the heading rule of the #) "# This file describes the network interfaces available on your system "# and how to activate them. For more information, see interfaces(5). "# The loopback network interface auto lo iface lo inet loopback "# The primary network interface auto eth0 iface eth0 inet dhcp If this is the case then this clearly doesn't contain what it should do but I don't how to fix it. Nor do I even know if I'm on the right track. Any help would be appreciated thanks :)

  Read the article

• Iptables working strangely

  - by user109985

  I have Ubuntu 12.04 x64 installed in my laptop. I'm quite new to linux, and I wanted to specify certain rules for the iptables firewall. This is the saved config of my iptables: *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A PREROUTING -p tcp -m tcp --dport 3306 -j DNAT --to-destination 192.168.1.100:3306 -A PREROUTING -p tcp -m tcp --dport 11002 -j DNAT --to-destination 192.168.1.100:11002 -A PREROUTING -p tcp -m tcp --dport 13000 -j DNAT --to-destination 192.168.1.100:13000 -A PREROUTING -p tcp -m tcp --dport 13001 -j DNAT --to-destination 192.168.1.100:13001 -A PREROUTING -p tcp -m tcp --dport 13002 -j DNAT --to-destination 192.168.1.100:13002 -A PREROUTING -p tcp -m tcp --dport 13003 -j DNAT --to-destination 192.168.1.100:13003 -A PREROUTING -p tcp -m tcp --dport 13004 -j DNAT --to-destination 192.168.1.100:13004 -A PREROUTING -p tcp -m tcp --dport 13061 -j DNAT --to-destination 192.168.1.100:13061 -A PREROUTING -p tcp -m tcp --dport 13099 -j DNAT --to-destination 192.168.1.100:13099 -A POSTROUTING -j MASQUERADE COMMIT *filter :INPUT DROP [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT COMMIT In theory, what it does is to drop all connections in all ports except for http, mysql and few other ports. Moreover, it redirects all mysql and 13000-13004..etc port connections to a specific local ip in the same port, which is 192.168.1.100. But what I find strange is that when my firewall is active, it blocks absolutely all the input connections, even those which must not block (http, mysql). In fact, I'm literally blocked and I can't establish any external connection. What am I doing wrong? PS: I tested the firewall without those redirections, and it still block all inputs, so I suppose it's not the problem.

  Read the article

• Unable to get wireless card working properly in DELL D620 laptop - Zorin OS 6.0 (3.2.0)

  - by ElliTech

  I have a DELL D620 laptop running Zorin OS 6.0 (3.2.0) The wireless was working prior to running Update Manager. Here is the output from some commands: dell@dell-lt:/$ rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no dell@dell-lt:/$ iwconfig lo no wireless extensions. eth0 no wireless extensions. dell@dell-lt:/$ ifconfig -a eth0 Link encap:Ethernet HWaddr 00:18:8b:d4:d8:2f inet addr:192.168.1.74 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::218:8bff:fed4:d82f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22227 errors:0 dropped:0 overruns:0 frame:0 TX packets:15027 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26452734 (26.4 MB) TX bytes:1708955 (1.7 MB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I am at a loss as to how to get the wireless working!!! ElliTech

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• Soft lockup after upgrade - cannot install from live CD

  - by nbm

  I dual-boot MacIntel Core 2 duo. nVidia graphics. Ran upgrade from ubuntu 13.10 to 14.04 (64 bit). On restart ran into {numbers} Bug: soft lockup - CPU#0 stuck for 22s! [swapper/0:1] Tried loading earlier kernel: same problem Tried re-installing ubuntu from a liveCD that has worked in the past: version 13.04. Same problem. Tried re-partitioning hard drive using Mac OS X disk utility and then installing ubuntu 14.04LTS from liveCD. Same problem. Not possible to verify liveCD disk (creates same "soft lockup" bug.) Tried installing from the liveCD with version 13.04 that I know works (that's how I got Ubuntu on this machine in the first place.) Same problem. I know this is not a hardware problem as OS X works just fine, I am using it right now on the same machine. I have been using various versions of Ubuntu for 2 years. Things I cannot do: Open a terminal Verify CD image Start ubuntu from CD (same soft lockup problem) This problem is similar to some other questions, none of which have been satisfactorily answered: Ubuntu 14.04 soft lockup on Vostro 3500 Cannot do fresh install of Ubuntu 13.04 while booting from DVD: "soft lockup" bug Live CD stalls when installing Ubuntu 13.10 UPDATE 6/11/14: Following some much-appreciated advice from bain (see below) I burned a 12.04LTS disk and started with kernel parameters: noapic, no1apic, acpi=off, nomodeset, elevator=deadline, and clocksource=jiffies. With all of these parameters I was able to load the 12.04LTS CD ("Try without installing"). It worked fine. However, as soon as I tried to install Ubuntu from the CD, my wired ethernet (eth0) connection would hang. There are already various askubuntu questions and bug reports about this problem, none of which had answers for me. (E.g., dhclient eth0 does nothing, none of the various reset commands does anything, manually setting IP &etc does nothing. I could reliably kill the ethernet connection by clicking "install ubuntu" every single time.) I could go ahead and install 12.04 without an internet connection, but the install would freeze after mostly completing (I tried several times.) There were some relevant error messages in the details of the install output script that, IIRC, had to do with searching for missing files and not being able to access eth0 (internet) to get them. To be honest I gave up at that point and I'm not sure I wrote those down. If I find some notes I will post them. At this point I no longer have Ubuntu on my system. I wiped the partitions and am using exclusively OS X. I am leaving this question in case it helps anyone else with similar problems. I love open source and I love Linux, and the next machine I get I will probably just build from Arch. At the moment I miss repositories and a lot of other things about Ubuntu, but the OS X terminal is 'nix, I can pretty much use all the open source apps I like, and while I am not a fan of the Apple software it gets the job done for me. Unlike Ubuntu, which can't even install. I realize this isn't necessarily a place for a soapbox speech, but when I first installed 12.04 several years ago there were already people in the community complaining that Canonical was going too "commercial". But I loved it. Several years later and all I've seen is Canonical adding more not-so-useful bells and whistles to Ubuntu while continually failing to fix basic problems on upgrades. With a dual-boot (and sometimes triple-boot) system it always took me some tweaking to get an upgrade to work, and to some extent that is okay. But at this point I feel like Canonical ought to just put a price tag on Ubuntu. All I see is more commercialism and advertising and product tie-ins, and ongoing problems do not get fixed. I am a big fan of open-source, not-for profit enterprise. I am also a big fan of for-profit enterprise, which certainly has its place and usefulness. I am not a fan of companies who pretend to be in favor of open source but really are just out to make a buck, and IMNSHO that is what Canonical has become. This is a great community and I wish you all the best, but my next install of Linux will not be Ubuntu.

  Read the article

• Kernel oops on Linux running in VirtualBox breaks some IO-related functionality on the server

  - by Kristoffer E

  We are having problems with CentOS release 6.3 running in VirtualBox on Windows 7 machines. The symptoms are the following: Everything works as normal for several hours, even days. Then something happens which breaks the system. What we still can do after this something happens: Access the web server Use existing SSH sessions to run top and free What does not work: Starting new SSH sessions (hangs after username and password is entered) Running ls in existing SSH sessions (hangs) SSI includes from our web servers that fetch data from remote machines probably more What we see on the server when this something happens is the following: Load average go from basically nothing to around 3 CPU usage is still low (5%) Disk activity is low (running iostat) Plenty of memory available Plenty of disk space available In /var/log/messages we get the following: Jun 14 01:10:48 devvm kernel: e1000 0000:00:03.0: eth0: Detected Tx Unit Hang Jun 14 01:10:48 devvm kernel: Tx Queue <0> Jun 14 01:10:48 devvm kernel: TDH <2e> Jun 14 01:10:48 devvm kernel: TDT <30> Jun 14 01:10:48 devvm kernel: next_to_use <30> Jun 14 01:10:48 devvm kernel: next_to_clean <2e> Jun 14 01:10:48 devvm kernel: buffer_info[next_to_clean] Jun 14 01:10:48 devvm kernel: time_stamp <1038284db> Jun 14 01:10:48 devvm kernel: next_to_watch <2f> Jun 14 01:10:48 devvm kernel: jiffies <103828b42> Jun 14 01:10:48 devvm kernel: next_to_watch.status <0> Jun 14 01:10:50 devvm kernel: e1000 0000:00:03.0: eth0: Detected Tx Unit Hang Jun 14 01:10:50 devvm kernel: Tx Queue <0> Jun 14 01:10:50 devvm kernel: TDH <2e> Jun 14 01:10:50 devvm kernel: TDT <30> Jun 14 01:10:50 devvm kernel: next_to_use <30> Jun 14 01:10:50 devvm kernel: next_to_clean <2e> Jun 14 01:10:50 devvm kernel: buffer_info[next_to_clean] Jun 14 01:10:50 devvm kernel: time_stamp <1038284db> Jun 14 01:10:50 devvm kernel: next_to_watch <2f> Jun 14 01:10:50 devvm kernel: jiffies <103829312> Jun 14 01:10:50 devvm kernel: next_to_watch.status <0> Jun 14 01:10:52 devvm kernel: ------------[ cut here ]------------ Jun 14 01:10:52 devvm kernel: WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26d/0x280() (Not tainted) Jun 14 01:10:52 devvm kernel: Hardware name: VirtualBox Jun 14 01:10:52 devvm kernel: NETDEV WATCHDOG: eth0 (e1000): transmit queue 0 timed out Jun 14 01:10:52 devvm kernel: Modules linked in: vboxsf(U) ipv6 ppdev parport_pc parport microcode sg vboxguest(U) i2c_piix4 i2c_core e1000 snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc pcnet32 mii ext4 mbcache jbd2 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] Jun 14 01:10:52 devvm kernel: Pid: 0, comm: swapper Not tainted 2.6.32-279.el6.x86_64 #1 Jun 14 01:10:52 devvm kernel: Call Trace: Jun 14 01:10:52 devvm kernel: <IRQ> [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0 Jun 14 01:10:52 devvm kernel: [<ffffffff8106b836>] ? warn_slowpath_fmt+0x46/0x50 Jun 14 01:10:52 devvm kernel: [<ffffffff814595fd>] ? dev_watchdog+0x26d/0x280 Jun 14 01:10:52 devvm kernel: [<ffffffff81099138>] ? sched_clock_cpu+0xb8/0x110 Jun 14 01:10:52 devvm kernel: [<ffffffff81459390>] ? dev_watchdog+0x0/0x280 Jun 14 01:10:52 devvm kernel: [<ffffffff8107e897>] ? run_timer_softirq+0x197/0x340 Jun 14 01:10:52 devvm kernel: [<ffffffff810a21c0>] ? tick_sched_timer+0x0/0xc0 Jun 14 01:10:52 devvm kernel: [<ffffffff8102b40d>] ? lapic_next_event+0x1d/0x30 Jun 14 01:10:52 devvm kernel: [<ffffffff81073ec1>] ? __do_softirq+0xc1/0x1e0 Jun 14 01:10:52 devvm kernel: [<ffffffff81096c50>] ? hrtimer_interrupt+0x140/0x250 Jun 14 01:10:52 devvm kernel: [<ffffffff8100c24c>] ? call_softirq+0x1c/0x30 Jun 14 01:10:52 devvm kernel: [<ffffffff8100de85>] ? do_softirq+0x65/0xa0 Jun 14 01:10:52 devvm kernel: [<ffffffff81073ca5>] ? irq_exit+0x85/0x90 Jun 14 01:10:52 devvm kernel: [<ffffffff81505be0>] ? smp_apic_timer_interrupt+0x70/0x9b Jun 14 01:10:52 devvm kernel: [<ffffffff8100bc13>] ? apic_timer_interrupt+0x13/0x20 Jun 14 01:10:52 devvm kernel: <EOI> [<ffffffff810387cb>] ? native_safe_halt+0xb/0x10 Jun 14 01:10:52 devvm kernel: [<ffffffff810149cd>] ? default_idle+0x4d/0xb0 Jun 14 01:10:52 devvm kernel: [<ffffffff81009e06>] ? cpu_idle+0xb6/0x110 Jun 14 01:10:52 devvm kernel: [<ffffffff814e433a>] ? rest_init+0x7a/0x80 Jun 14 01:10:52 devvm kernel: [<ffffffff81c21f7b>] ? start_kernel+0x424/0x430 Jun 14 01:10:52 devvm kernel: [<ffffffff81c2133a>] ? x86_64_start_reservations+0x125/0x129 Jun 14 01:10:52 devvm kernel: [<ffffffff81c21438>] ? x86_64_start_kernel+0xfa/0x109 Jun 14 01:10:52 devvm kernel: ---[ end trace 2c7bb984812cf120 ]--- Jun 14 01:10:52 devvm kernel: e1000 0000:00:03.0: eth0: Reset adapter Jun 14 01:10:53 devvm abrtd: Directory 'oops-2013-06-14-01:10:53-1537-0' creation detected Jun 14 01:10:53 devvm abrt-dump-oops: Reported 1 kernel oopses to Abrt Jun 14 01:10:53 devvm abrtd: Can't open file '/var/spool/abrt/oops-2013-06-14-01:10:53-1537-0/uid': No such file or directory Jun 14 01:10:55 devvm kernel: Bridge firewalling registered After this we see for a while, every two minutes: Jun 14 01:14:22 devvm kernel: INFO: task events/0:19 blocked for more than 120 seconds. Jun 14 01:14:22 devvm kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jun 14 01:14:22 devvm kernel: events/0 D 0000000000000000 0 19 2 0x00000000 Jun 14 01:14:22 devvm kernel: ffff880116c4fb90 0000000000000046 00000000ffffffff 0000000000000008 Jun 14 01:14:22 devvm kernel: 0000000000016680 0000000000016680 ffff880028210400 0000000000016680 Jun 14 01:14:22 devvm kernel: ffff880116c4daf8 ffff880116c4ffd8 000000000000fb88 ffff880116c4daf8 Jun 14 01:14:22 devvm kernel: Call Trace: Jun 14 01:14:22 devvm kernel: [<ffffffff8105b483>] ? perf_event_task_sched_out+0x33/0x80 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe6a5>] schedule_timeout+0x215/0x2e0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100975d>] ? __switch_to+0x13d/0x320 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe323>] wait_for_common+0x123/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff81060250>] ? default_wake_function+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe43d>] wait_for_completion+0x1d/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d093>] __cancel_work_timer+0x1b3/0x1e0 Jun 14 01:14:22 devvm kernel: [<ffffffff8108cbe0>] ? wq_barrier_func+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d0f0>] cancel_work_sync+0x10/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffffa01c5ca5>] e1000_down_and_stop+0x25/0x50 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cb695>] e1000_down+0x155/0x200 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cbcb0>] ? e1000_reset_task+0x0/0xe0 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cbd1e>] e1000_reset_task+0x6e/0xe0 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffff8108c760>] worker_thread+0x170/0x2a0 Jun 14 01:14:22 devvm kernel: [<ffffffff810920d0>] ? autoremove_wake_function+0x0/0x40 Jun 14 01:14:22 devvm kernel: [<ffffffff8108c5f0>] ? worker_thread+0x0/0x2a0 Jun 14 01:14:22 devvm kernel: [<ffffffff81091d66>] kthread+0x96/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100c14a>] child_rip+0xa/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff81091cd0>] ? kthread+0x0/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100c140>] ? child_rip+0x0/0x20 Jun 14 01:14:22 devvm kernel: INFO: task parted:8069 blocked for more than 120 seconds. Jun 14 01:14:22 devvm kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jun 14 01:14:22 devvm kernel: parted D 0000000000000003 0 8069 7994 0x00000080 Jun 14 01:14:22 devvm kernel: ffff8800908b3bb8 0000000000000082 0000000000000000 ffff88010ab50080 Jun 14 01:14:22 devvm kernel: ffff880116c7d500 0000000000000001 0000000000000000 0000000000000000 Jun 14 01:14:22 devvm kernel: ffff88010ab50638 ffff8800908b3fd8 000000000000fb88 ffff88010ab50638 Jun 14 01:14:22 devvm kernel: Call Trace: Jun 14 01:14:22 devvm kernel: [<ffffffff814fe6a5>] schedule_timeout+0x215/0x2e0 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe323>] wait_for_common+0x123/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff81060250>] ? default_wake_function+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8112b6d0>] ? lru_add_drain_per_cpu+0x0/0x10 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe43d>] wait_for_completion+0x1d/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d177>] flush_work+0x77/0xc0 Jun 14 01:14:22 devvm kernel: [<ffffffff8108cbe0>] ? wq_barrier_func+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d2f3>] schedule_on_each_cpu+0x133/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff811ad440>] ? invalidate_bh_lru+0x0/0x50 Jun 14 01:14:22 devvm kernel: [<ffffffff8112ae35>] lru_add_drain_all+0x15/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff811adf6a>] invalidate_bdev+0x2a/0x50 Jun 14 01:14:22 devvm kernel: [<ffffffff8125e9a4>] blkdev_ioctl+0x3b4/0x6e0 Jun 14 01:14:22 devvm kernel: [<ffffffff811b381c>] block_ioctl+0x3c/0x40 Jun 14 01:14:22 devvm kernel: [<ffffffff8118dec2>] vfs_ioctl+0x22/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8118e064>] do_vfs_ioctl+0x84/0x580 Jun 14 01:14:22 devvm kernel: [<ffffffff8118e5e1>] sys_ioctl+0x81/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b In /var/spool/abrt/oops-2013-06-14-01:10:53-1537-0 we can see the following information: In backtrace: WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26d/0x280() (Not tainted) Hardware name: VirtualBox NETDEV WATCHDOG: eth0 (e1000): transmit queue 0 timed out Modules linked in: vboxsf(U) ipv6 ppdev parport_pc parport microcode sg vboxguest(U) i2c_piix4 i2c_core e1000 snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc pcnet32 mii ext4 mbcache jbd2 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] Pid: 0, comm: swapper Not tainted 2.6.32-279.el6.x86_64 #1 Call Trace: <IRQ> [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0 [<ffffffff8106b836>] ? warn_slowpath_fmt+0x46/0x50 [<ffffffff814595fd>] ? dev_watchdog+0x26d/0x280 [<ffffffff81099138>] ? sched_clock_cpu+0xb8/0x110 [<ffffffff81459390>] ? dev_watchdog+0x0/0x280 [<ffffffff8107e897>] ? run_timer_softirq+0x197/0x340 [<ffffffff810a21c0>] ? tick_sched_timer+0x0/0xc0 [<ffffffff8102b40d>] ? lapic_next_event+0x1d/0x30 [<ffffffff81073ec1>] ? __do_softirq+0xc1/0x1e0 [<ffffffff81096c50>] ? hrtimer_interrupt+0x140/0x250 [<ffffffff8100c24c>] ? call_softirq+0x1c/0x30 [<ffffffff8100de85>] ? do_softirq+0x65/0xa0 [<ffffffff81073ca5>] ? irq_exit+0x85/0x90 [<ffffffff81505be0>] ? smp_apic_timer_interrupt+0x70/0x9b [<ffffffff8100bc13>] ? apic_timer_interrupt+0x13/0x20 <EOI> [<ffffffff810387cb>] ? native_safe_halt+0xb/0x10 [<ffffffff810149cd>] ? default_idle+0x4d/0xb0 [<ffffffff81009e06>] ? cpu_idle+0xb6/0x110 [<ffffffff814e433a>] ? rest_init+0x7a/0x80 [<ffffffff81c21f7b>] ? start_kernel+0x424/0x430 [<ffffffff81c2133a>] ? x86_64_start_reservations+0x125/0x129 [<ffffffff81c21438>] ? x86_64_start_kernel+0xfa/0x109 In cmdline: ro root=/dev/mapper/vg_01-lv_root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD SYSFONT=latarcyrheb-sun16 rd_LVM_LV=vg_01/lv_root crashkernel=129M@0M rhgb quiet rd_LVM_LV=vg_01/lv_swap rd_NO_DM rhgb quie Additional information: # uname -a Linux devvm 2.6.32-279.el6.x86_64 #1 SMP Fri Jun 22 12:19:21 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux # cat /etc/redhat-release CentOS release 6.3 (Final) VirtualBox version 4.2.6. Any insight in how we can proceed with troubleshooting this is appreciated. If you need more information, just let me know.

  Read the article

• Wireless Connected But No Internet Connection (Ubuntu 12.04)

  - by Zxy

  I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

  Read the article

• RHEL 5 SCSI ADPATEC

  - by Rajiv Sharma

  HI I have RHEL 5 box . and adpatec scsi card connected to it . I can see the adaptor under dsmeg | grep -i scsi dmesg | grep -i scsi SCSI subsystem initialized scsi0 : SCSI emulation for USB Mass Storage devices Type: CD-ROM ANSI SCSI revision: 00 scsi 0:0:0:0: Attached scsi generic sg0 type 5 sr0: scsi3-mmc drive: 0x/0x caddy sr 0:0:0:0: Attached scsi CD-ROM sr0 scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs Loading iSCSI transport class v2.0-871. iscsi: registered transport (iser) iscsi: registered transport (cxgb3i) Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.0 (Dec 06, 2009) iscsi: registered transport (bnx2i) scsi2 : Broadcom Offload iSCSI Initiator scsi3 : Broadcom Offload iSCSI Initiator iscsi: registered transport (tcp) iscsi: registered transport (be2iscsi) bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth1 bnx2i: iSCSI not supported, dev=eth1 but cann't see under cat /proc/scsi/scsi cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: KVM Model: vmDisk-CD Rev: 0.01 Type: CD-ROM ANSI SCSI revision: 02 all st and sg modules are enable. Anyone please help me thanks advance Rajiv

  Read the article

• Restricting dnsmasq's DHCP server to one interface

  - by Delan Azabani

  How do I configure dnsmasq to only assign addresses on eth0, not wlan0?

  Read the article

• How do i get the default gateway in LINUX given the destination?

  - by Suezy

  Good day! I'm trying to get the default gateway, using the destination 0.0.0.0 i used this command: netstat -rn | grep 0.0.0.0 and it returns this list: Destination Gateway Genmask Flags MSS Window irtt Iface 10.9.9.17 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 133.88.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 133.88.31.70 0.0.0.0 UG 0 0 0 eth0 My goal here is to ping the default gateway using destination 0.0.0.0; thus, that is "133.88.31.70"; but this one returns a list because of using 'grep'. Question is: How do i get the default gateway only? I will need it for my bash script to identify if net connection is up or not. Any answers will be much appreciated. =)

  Read the article

• How to Grab MAC Address of Active Ethernet Connection in Bash Script?

  - by Huy Tran

  Simple Question: How do I grab the MAC address of the active Ethernet connection in a bash script? I currently have: set - `/sbin/ifconfig eth0 | head -1` MAC=$5 Which outputs the MAC address of the eth0, but if it's eth1 that's active, I want that instead. Could I beforehand execute ifconfig | grep inet but that wouldn't tell me which interface is active, just that one is active. I need to grab the line above it to tell me which one is the active connection. Any help would be much appreciated. Thank you!

  Read the article

• Debian, 6rd tunnel, and connection troubles

  - by Chris B

  Long story short I am having issues with IPv6 using a 6rd tunnel with my ISP, charter business. They offer a 6rd tunnel that I think I have properly set up, but the server doesn’t reply to every ipv6 request. When the server has the network interfaces idle with no traffic for about 10 minutes, then IPv6 stops accepting inbound connections. to re-allow it, I must go into the server, and make it do a outbound ipv6 connection (normally a ping) to start it back up. Whats weird though i that if I run iptraf when its not working, it still shows a inbound ipv6 packet… the server is just not replying, and I can’t figure out why. Also, if I try to access my server over IPv6 from a house about 1 mile away on the same ISP, it is never able to connect. it always times out, but again the iptraf shows a ipv6 inbound packet. Again, it just does not reply. To test if my server is accessible through IPv6 I always have to use my vzw 4g phone (they use IPv6) or ipv6proxy dot net. Here is all of the configuration information my ISP gives on there tunnel server: 6rd Prefix = 2602:100::/32 Border Relay Address = 68.114.165.1 6rd prefix length = 32 IPv4 mask length = 0 Here is my /etc/network/interfaces for ipv6 (used x's to block real addresses) auto charterv6 iface charterv6 inet6 v4tunnel address 2602:100:189f:xxxx::1 netmask 32 ttl 64 gateway ::68.114.165.1 endpoint 68.114.165.1 local 24.159.218.xxx up ip link set mtu 1280 dev charterv6 here is my iptables config filter :INPUT DROP [0:0] :fail2ban-ssh – [0:0] :OUTPUT ACCEPT [0:0] :FORWARD DROP [0:0] :hold – [0:0] -A INPUT -p tcp -m tcp —dport 22 -j fail2ban-ssh -A INPUT -m state —state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m multiport -j ACCEPT —dports 80,443,25,465,110,995,143,993,587,465,22 -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp —dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp —dport 5900:5910 -j ACCEPT -A fail2ban-ssh -j RETURN -A INPUT -p icmp -j ACCEPT COMMIT and last here is my ip6tables firewall config filter :INPUT DROP [1653:339023] :FORWARD DROP [0:0] :OUTPUT ACCEPT [60141:13757903] :hold – [0:0] -A INPUT -m state —state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m multiport —dports 80,443,25,465,110,995,143,993,587,465,22 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp —dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp —dport 5900:5910 -j ACCEPT -A INPUT -p ipv6-icmp -j ACCEPT COMMIT So Summary: 1.iptraf always shows IPv6 traffic, so its always making it to the server 2.server stops replying on ipv6 after no traffic for awhile (10 minutesish) until a outbound connection is made, then the process repeats. 3.server is NEVER accessable vi same ISP (yet iptraf still shows ipv6 request) Notes: When I try to access it from the same ISP from across town, even with iptables and ip6tables allowing ALL inbound traffic, this is what iptraf shows. IPv6 (92 bytes) from 97.92.18.xxx to 24.159.218.xxx on eth0 ICMP dest unrch (port) (120 bytes) from 24.159.218.xxx to 97.92.18.xxx on eth1 its strange, like its trying to forward to LAN? (eth1 is LAN, eth0 is WAN) even with the IPv6 address being set in the hosts file to the servers domain name. With iptables set up normally with the above configurations it only says this: IPv6 (100 bytes) from 97.92.18.xxx to 24.159.218.xxx on eth0 Im REALLY stuck on this, and any help would be GREATLY appreciated.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >