Search Results

Search found 2649 results on 106 pages for 'signal slot'.

Page 29/106 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Only half of RAM is recognized by BIOS

  - by Rick Crawford

  I got a Gigabyte GA-P35-DS3 mainboard. Some time ago I noticed that Windows only showed 2GB instead of 4GB. I don't know exactly what caused it anyway. I tried putting in each of the 4 x 1GB RAM modules one by one, and tried every slot one by one, until every stick and slot worked. However, then I tried adding one more at a time, and it kept showing 1GB, until I put in all 4, where it only showed 2 GB instead of 4 (in BIOS and windows 7 64bit). I tried replacing the BIOS battery since I've read that low battery could cause it. It didn't help though. I also bought 4GB new RAM (yes, it's supported, I checked it), and it's still the same, it only shows 2GB (or 3GB, when I put in 4 of the new and 2 of the old). I also did the latest BIOS update, and used default BIOS settings, but nothing of that helped. When my PC boots it shows "RAM modules used 2 and 3", when 4 sticks are in - or "0 and 1", when only 2 are in.

  Read the article

• unable to install anything on ubuntu 9.10 with aptitude

  - by Srisa

  Hello, Earlier i could install software by using the 'sudo aptitude install ' command. Today when i tried to install rkhunter i am getting errors. It is not just rkhunter, i am not able to install anything. Here is the text output: user@server:~$ sudo aptitude install rkhunter ................ ................ 20% [3 rkhunter 947/271kB 0%] Get:4 http://archive.ubuntu.com karmic/universe unhide 20080519-4 [832kB] 40% [4 unhide 2955/832kB 0%] 100% [Working] Fetched 1394kB in 1s (825kB/s) Preconfiguring packages ... Selecting previously deselected package lsof. (Reading database ... ................ (Reading database ... 95% (Reading database ... 100% (Reading database ... 20076 files and directories currently installed.) Unpacking lsof (from .../lsof_4.81.dfsg.1-1_amd64.deb) ... dpkg: error processing /var/cache/apt/archives/lsof_4.81.dfsg.1-1_amd64.deb (--unpack): unable to create `/usr/bin/lsof.dpkg-new' (while processing `./usr/bin/lsof'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Selecting previously deselected package libmd5-perl. Unpacking libmd5-perl (from .../libmd5-perl_2.03-1_all.deb) ... Selecting previously deselected package rkhunter. Unpacking rkhunter (from .../rkhunter_1.3.4-5_all.deb) ... dpkg: error processing /var/cache/apt/archives/rkhunter_1.3.4-5_all.deb (--unpack): unable to create `/usr/bin/rkhunter.dpkg-new' (while processing `./usr/bin/rkhunter'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Selecting previously deselected package unhide. Unpacking unhide (from .../unhide_20080519-4_amd64.deb) ... dpkg: error processing /var/cache/apt/archives/unhide_20080519-4_amd64.deb (--unpack): unable to create `/usr/sbin/unhide-posix.dpkg-new' (while processing `./usr/sbin/unhide-posix'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Processing triggers for man-db ... Errors were encountered while processing: /var/cache/apt/archives/lsof_4.81.dfsg.1-1_amd64.deb /var/cache/apt/archives/rkhunter_1.3.4-5_all.deb /var/cache/apt/archives/unhide_20080519-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up libmd5-perl (2.03-1) ... Building dependency tree... 0% Building dependency tree... 50% Building dependency tree... 50% Building dependency tree Reading state information... 0% ........... .................... I have removed some lines to reduce the text. All the error messages are in here though. My experience with linux is limited and i am not sure what the problem is or how it is to be resolved. Thanks.

  Read the article

• How do I get 480i resolution for an external monitor in Windows 7?

  - by Carson Myers

  I'm trying to get a laptop video signal to my really old television, so that I can play movies on it. But the TV won't accept the video signal. I found the manual online, and apparently the output has to be 480i. But I don't know how to do that -- Windows 7 will only let me set the resolution down to 800x600. Even if I get it down to 640x480- is that 480i or 480p? How do I tell the difference? How do I switch between them? How do I get the resolution down so low in the first place?

  Read the article

• Installing mod_xsendfile on MAMP

  - by mail4alberto

  Hello, I'm having trouble installing mod_xsendfile on MAMP. I've used some sources to try to help me install it: http://iprog.com/posting/2008/04/compiling_mod_xsendfile_for_mac_os_x http://groups.google.com/group/phusion-passenger/browse_thread/thread/e6dac9d5ea0de9c1 I ended up installing apache20 via macports and used apsx command to create the module and then copy it into MAMP's modules folder. I was able to seem to load the module at least. But then I get this error in my apache logs: [Thu May 27 19:08:28 2010] [notice] child pid 68606 exit signal Bus error (10) [Thu May 27 19:08:41 2010] [notice] child pid 68607 exit signal Bus error (10) Can anyone help me out? :S

  Read the article

• Why can't connect with second computer in same LAN and settings?

  - by user930450

  I'm trying to connect to WLAN with notebook. The notebook works fine with other WLANs. It can authenticate, signal is "very good" but it says "can't access internet". (On Windows it's small yellow exclamation mark on the signal). With other computer exactly in the same location, with the same settings, it's possible to connect. Both are configurated to get IP dynamically. One difference is that the other computer is using "Ralink wireless" instead normal windows client to connect. But does this make a difference? the settings are the same. What could be the reason?

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• Brand New Monitor Won't Get Input From Computer

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• HP Z210 SFF: two different video cards produce no Displayport output when installed

  - by ConcernedOfTunbridgeWells

  I have a HP Z210 SFF that I'm trying to install a video card into. I've tried two different cards in Slot 2 (a Quadro FX380LP and a Quadro 600). Neither of these cards produce a displayport signal when installed. With neither installed the displayport port on the motherboard works fine with the built in graphics. When I install the cards it produces no signal and the cards don't either. The Quadro 600 is brand new and the odds of having two dead video cards is quite low. Is there something fundamental that I could be missing out - a BIOS setting maybe?

  Read the article

• Any dangers in using DDR memory with a higher frequency than the FSB?

  - by raw_noob

  I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

  Read the article

• How to programmatically control slave computer on BIOS level?

  - by PovilasSid

  I want to run some test on hardware level. My goal is to create or find a way to control one computer from another down to BIOS settings changing. For example: Master computer sends a signal for slave to restart and opens BIOS settings dialog. Master computer sends a signal to slave to change BIOS parameters and then restart. Then slave fully boots up master starts up some software on slave. Then software finishes operations cycle continues till certain conditions are met. I know that I am looking for a complex thing but mainly what I need are correct keywords because now I am being flooded by BIOS configurations tutorials. Main concerns: Is it possible without using any custom tailer chip? How can master monitor salve`s hardware activity? How to let master handled more than one slave? How what connections are needed to create this kind of setup? (cables)

  Read the article

• Is it possible to make Ctrl+C as responsive as Ctrl+Break in the Windows 7 console?

  - by Peter Graham

  Is it possible to make Ctrl+C act like Ctrl+Break in the Windows 7 cmd.exe console? By default Ctrl+C seems to only send a signal the next time the input buffer is read, where Ctrl+Break sends a signal immediately. This makes Ctrl+C useless for ending processes because when I want to end a process I want to end it immediately. I'm using Ctrl+Break for now but it's far harder to type. It looks like in DOS you can add BREAK=ON to CONFIG.SYS to achieve this, but not in Windows 7?

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• No break compatible with Linux box?

  - by Somebody still uses you MS-DOS

  I'm buying this unit from deal extreme: it's a bitorrent downloader, with NAS capability. I'm interested in sharing an external HD in it, with media and backup purposes. I'm afraid of energy problems (don't know if this is the correct term), corrupting my mounted drives (like after a storm), so I thought about buying a No Break that sends a "signal" to my Linux box, and a script in my Linux box would unmout everything to avoid problems. Do this "No Break signal" feature exists? Do you have model suggestions? Thanks!

  Read the article

• How to recover my invisible HD again?

  - by pattulus

  I made this several times now, but this time something bad happened. What I did: I installed Windows 7 at a 32GB partition on my slot 2 HD in my MacPro. Windows 7 made a 105MB partition… I knew this before, but what I didn’t know was that this partition is now on my slot 4 HD. My home folder, my private videos and some other stuff are on this 1TB drive. What I found out so far: I’m currently logged in as another admin since my OS partition as well as the two other HD's aren't harmed. Disk Utility: … only shows the 105MB NTSF partition on this 1TB volume. It isn’t showing my old 1TB partition/ex-HD named "storehouse". Only the partition tab is telling me that there now is a 1TB empty free unpartitioned space. Data Rescue II: … is showing the Volume as it used to be with it's old Name "storehouse". A quick scan and a thorough scan both were done in 1 second which leds me to the conclusion that there's isn’t something deleted at all (» hope!). Data Rescue doesn’t even mention the damn "system reserved" partition. Drive Genius: … also shows the old partition and doesn’t mention the new one. But looking at the info it tells me under "content": FDisk_partition_scheme (instead of Apple_partition_scheme). Well D'oh…. Tech Tools: … doesn’t show the volume, otherwise I'd might have been tempted to press rebuild/repair. What to do next?? I think the best approach is to buy another 1TB HD and let Disk Warrior Clone my old one to it… just to be on the safe side. But what is the best thing to do after this… ???

  Read the article

• Random Server shutdown? - CentOS

  - by Kevin Hammett

  My system was working fine, and then it just had a random restart. Anyone have any idea of the problem? The message log: Jul 6 22:56:34 909I7 shutdown[719711]: shutting down for system halt Jul 6 22:56:34 909I7 init: Switching to runlevel: 0 Jul 6 22:56:35 909I7 smartd[10743]: smartd received signal 15: Terminated Jul 6 22:56:35 909I7 smartd[10743]: smartd is exiting (exit status 0) Jul 6 22:56:42 909I7 hcid[8749]: Got disconnected from the system message bus Jul 6 22:56:42 909I7 auditd[8430]: The audit daemon is exiting. Jul 6 22:56:42 909I7 kernel: audit(1341640602.922:344412): audit_pid=0 old=8430 by auid$ Jul 6 22:56:43 909I7 pcscd: pcscdaemon.c:572:signal_trap() Preparing for suicide Jul 6 22:56:43 909I7 pcscd: hotplug_libusb.c:376:HPRescanUsbBus() Hotplug stopped Jul 6 22:56:44 909I7 pcscd: readerfactory.c:1379:RFCleanupReaders() entering cleaning f$ Jul 6 22:56:44 909I7 pcscd: pcscdaemon.c:532:at_exit() cleaning /var/run Jul 6 22:56:44 909I7 kernel: Kernel logging (proc) stopped. Jul 6 22:56:44 909I7 kernel: Kernel log daemon terminating. Jul 6 22:56:45 909I7 exiting on signal 15

  Read the article

• I need to preserve a tape using symantec backup exec. I'm aving trouble doing so

  - by MrVimes

  Please forgive me if this is the wrong stack exchange site. Please suggest which one I should post this to if it is. There's an automatic tape machine running in a remote location, with software (symantec backup exec 11d) Recently one of the servers being backed up had problems with its raid controller, so one of the drives has become invisible. I need to preserve the last good backup of that drive so I am trying to replace the tape with the most recent backup of that drive on it with one of the scratch tapes (blank tapes) present in the machine. I've tried the following... Associate the blank media with the media set in question (Wednesday) For the existing media (the tape with the data I want to keep) I click 'move to vault' and move it to the offline vault. I associate it with something other than 'Wednesday' (a media set called 'keep data infinitely...') I then do an inventory on that slot. The above steps I'm led to believe are supposed to put the fresh tape in the slot that had the tape I want to keep in it. But it just keeps showing up as containing the tape I want to keep after the inventory. (after refreshing the device tree) I am a complete newbie with this software. Can you tell me what I'm doing wrong, and/or tell me how to acheive my desired goal Edit: Just want to point out that I did try to get help directly from symantec with this, but having jumped through countless hoops to create an account and create a support ticket my progress was halted by requiring something called a 'tecnical contact id' at the final step with no explanation of what it is or how to get one.

  Read the article

• Productive Writing Software

  - by Nick Retallack

  What do you guys use to write a personal journal, notes, and reference information that you want to group and search through later? I'm not one of those crazy people who likes to share their journal with the world. Some things I like to keep to myself. It's quite nice to have a reference. Preferences for cross-platform stuff (windows, mac, linux) Some Background For Windows, there's a program called Yeah Write, which really changed my expectations about how easy it should be to start writing something. You don't open or close files -- just click an empty slot and start writing, or click a filled slot to work on another file. And you can organize things into categories by creating tabs. Now that I carry a Macbook, I've just been using TextEdit. I like it because I can't lose my work when my computer crashes: it auto-saves everything and restores it when I launch TextEdit again. But I make a mess, leave thirty open files, and save everything to one directory with no tags for easy grouping. Saving files and selecting the directory they should be in is too clunky to do in the middle of a meeting. And organizing files into folders in the Finder is a pain, since there's no tree view like on Windows. Sure, I'm lazy, but I miss Yeah Write. I'm not going to get a windows laptop just to use it though. Since the laptop I take my notes on is a mac, I'm gonna be biased toward mac solutions.

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• How can I connect a DVI monitor to the VGA port in my laptop?

  - by Corey

  Is there a device I can buy that will convert the analog signal to digital?

  Read the article

• Win XP cannot connect (or see) my wifi network, but can see others

  - by Jorre

  since yesterday I have a strange wifi problem with my pc. I have a wireless linksys router setup that worked fine for many months, now since yesterday my pc won't connect to the wifi signal anymore. The strange thing is, my macbook pro still connects fine. SSID is broadcasting, but my windows XP doens't see it, I have all signal modes set to "auto". Windows XP sees all my neighbours wifi networks, so the wifi card isn't broken or anything. Any idea what can be wrong here?

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• UPS compatible with Linux box?

  - by Somebody still uses you MS-DOS

  I'm buying this unit from deal extreme: it's a bitorrent downloader, with NAS capability. I'm interested in sharing an external HD in it, with media and backup purposes. I'm afraid of energy problems (don't know if this is the correct term), corrupting my mounted drives (like after a storm), so I thought about buying an UPS that sends a "signal" to my Linux box, and a script in my Linux box would unmout everything to avoid problems. Do this "UPS signal" feature exists? Do you have model suggestions? Thanks!

  Read the article

• Is it better to use a crowded 2.4GHz Wi-Fi channel 1, 6, 11 or "unused" 3, 4, 8, or 9?

  - by Luke

  I understand that 2.4GHz Wi-Fi channels overlap, and that the only non-overlapping channels in the US are 1, 6, and 11. Generally, my signal strength on channels 1, 6, and 11 are much stronger than my neighbors' on the same channel. However, several of the channels may have 4 or 5 others on that same channel. In this scenario, is it better to use 3, 4, 8, or 9? Or is it better to use the crowded channels 1, 6, and 11? As a secondary question, does it even matter that my signal strength is much higher than theirs? Related: Why use wifi channels other than 1, 6 or 11?

  Read the article

• Is 50% download speed on a wireless G network normal?

  - by Bartlomiej Skwira

  I have a wired connection of about 36Mb/s, but my wireless speed is max at about 18-19Mb/s. I have a WRT54G-TM (T-Mobile, 802.11G) router with DD-WRT firmware - I've upgraded it to latest build. Done some settings changes: changed channel - 13 wireless network mode - G-only ACK Timing - 0 Fragmentation Threshold and RTS Threshold - 2304 Basic Rate - All Signal/Noise ratio: -46/-94, signal quality ~50-60%. Is this normal with G networks? Edit: The AP is located about 2 meters from laptop, no walls or metal objects, but its next to a TV. I've done a channel scan (had problems locating it, go to "Status - Wireless - Site survey" - lame naming) and everybody else is on channels 1 and 6. Switched to channel 11 but it didn't help. As for trasmit power I got best results with default 71mw. The antenna might be a factor, I'm using the default 2 antennas.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >