Search Results

Search found 18424 results on 737 pages for 'load balance'.

Page 290/737 | < Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >

• How to diagnose failing 6Gbps SATA connection?

  - by whitequark

  I have a Samsung RC530 notebook and OCZ Vertex-3 6Gbps SATA SSD working in AHCI mode. # dmesg | grep DMI SAMSUNG ELECTRONICS CO., LTD. RC530/RC730/RC530/RC730, BIOS 03WD.M008.20110927.PSA 09/27/2011 # lspci -nn 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) # sdparm -a /dev/sda /dev/sda: ATA OCZ-VERTEX3 2.15 At the boot, the following messages are present in dmesg (I am running Debian wheezy @ Linux 3.2.8): # dmesg | grep -iE '(ata|ahci)' [ 5.179783] ahci 0000:00:1f.2: version 3.0 [ 5.179802] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 5.179864] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X [ 5.195424] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode [ 5.195429] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst [ 5.195436] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.204035] scsi0 : ahci [ 5.204301] scsi1 : ahci [ 5.204447] scsi2 : ahci [ 5.204592] scsi3 : ahci [ 5.204682] scsi4 : ahci [ 5.204799] scsi5 : ahci [ 5.204917] ata1: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06100 irq 42 [ 5.204920] ata2: DUMMY [ 5.204923] ata3: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06200 irq 42 [ 5.204924] ata4: DUMMY [ 5.204926] ata5: DUMMY [ 5.204927] ata6: DUMMY [ 5.523039] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.525911] ata3.00: ATAPI: TSSTcorp CDDVDW SN-208BB, SC00, max UDMA/100 [ 5.531006] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 5.533703] ata3.00: configured for UDMA/100 [ 5.542790] ata1.00: ATA-8: OCZ-VERTEX3, 2.15, max UDMA/133 [ 5.542800] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 5.552751] ata1.00: configured for UDMA/133 [ 5.553050] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX3 2.15 PQ: 0 ANSI: 5 [ 5.559621] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208BB SC00 PQ: 0 ANSI: 5 [ 5.564059] sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB) [ 5.564127] sd 0:0:0:0: [sda] Write Protect is off [ 5.564131] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.564158] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.564582] sda: sda1 [ 5.564810] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.572006] sr0: scsi3-mmc drive: 16x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 5.572010] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 5.572189] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 6.717181] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen [ 6.717238] ata1.00: irq_stat 0x08000000, interface fatal error [ 6.717291] ata1: SError: { UnrecovData HostInt 10B8B BadCRC } [ 6.717342] ata1.00: failed command: READ FPDMA QUEUED [ 6.717395] ata1.00: cmd 60/50:00:20:39:58/00:00:00:00:00/40 tag 0 ncq 40960 in [ 6.717396] res 40/00:00:20:39:58/00:00:00:00:00/40 Emask 0x50 (ATA bus error) [ 6.717503] ata1.00: status: { DRDY } [ 6.717553] ata1: hard resetting link [ 7.033417] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.055234] ata1.00: configured for UDMA/133 [ 7.055262] ata1: EH complete [ 7.147280] ata1.00: exception Emask 0x10 SAct 0xf8 SErr 0x280100 action 0x6 frozen [ 7.147340] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.147393] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.147460] ata1.00: failed command: READ FPDMA QUEUED [ 7.147529] ata1.00: cmd 60/08:18:88:17:41/00:00:02:00:00/40 tag 3 ncq 4096 in [ 7.147531] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147691] ata1.00: status: { DRDY } [ 7.147754] ata1.00: failed command: READ FPDMA QUEUED [ 7.147821] ata1.00: cmd 60/00:20:f8:42:4c/01:00:02:00:00/40 tag 4 ncq 131072 in [ 7.147822] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147977] ata1.00: status: { DRDY } [ 7.148036] ata1.00: failed command: READ FPDMA QUEUED [ 7.148100] ata1.00: cmd 60/50:28:f8:43:4c/00:00:02:00:00/40 tag 5 ncq 40960 in [ 7.148101] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148255] ata1.00: status: { DRDY } [ 7.148315] ata1.00: failed command: READ FPDMA QUEUED [ 7.148379] ata1.00: cmd 60/00:30:50:98:64/01:00:02:00:00/40 tag 6 ncq 131072 in [ 7.148380] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148534] ata1.00: status: { DRDY } [ 7.148593] ata1.00: failed command: READ FPDMA QUEUED [ 7.148657] ata1.00: cmd 60/00:38:50:99:64/01:00:02:00:00/40 tag 7 ncq 131072 in [ 7.148658] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148813] ata1.00: status: { DRDY } [ 7.148875] ata1: hard resetting link [ 7.464842] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.486794] ata1.00: configured for UDMA/133 [ 7.486822] ata1: EH complete [ 7.546395] ata1.00: exception Emask 0x10 SAct 0x2f SErr 0x280100 action 0x6 frozen [ 7.546470] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.546531] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.546588] ata1.00: failed command: READ FPDMA QUEUED [ 7.546648] ata1.00: cmd 60/00:00:e0:4b:61/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.546649] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.546794] ata1.00: status: { DRDY } [ 7.546847] ata1.00: failed command: READ FPDMA QUEUED [ 7.546906] ata1.00: cmd 60/00:08:90:2f:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.546907] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547053] ata1.00: status: { DRDY } [ 7.547106] ata1.00: failed command: READ FPDMA QUEUED [ 7.547165] ata1.00: cmd 60/00:10:90:30:48/01:00:02:00:00/40 tag 2 ncq 131072 in [ 7.547166] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547310] ata1.00: status: { DRDY } [ 7.547363] ata1.00: failed command: READ FPDMA QUEUED [ 7.547422] ata1.00: cmd 60/00:18:50:c7:64/01:00:02:00:00/40 tag 3 ncq 131072 in [ 7.547423] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547568] ata1.00: status: { DRDY } [ 7.547621] ata1.00: failed command: READ FPDMA QUEUED [ 7.547681] ata1.00: cmd 60/00:28:e0:4c:61/01:00:02:00:00/40 tag 5 ncq 131072 in [ 7.547682] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547825] ata1.00: status: { DRDY } [ 7.547882] ata1: hard resetting link [ 7.864408] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.886351] ata1.00: configured for UDMA/133 [ 7.886375] ata1: EH complete [ 7.890012] ata1: limiting SATA link speed to 3.0 Gbps [ 7.890016] ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x280100 action 0x6 frozen [ 7.890093] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.890152] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.890210] ata1.00: failed command: READ FPDMA QUEUED [ 7.890272] ata1.00: cmd 60/00:00:90:33:48/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.890273] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890418] ata1.00: status: { DRDY } [ 7.890472] ata1.00: failed command: READ FPDMA QUEUED [ 7.890530] ata1.00: cmd 60/00:08:90:34:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.890531] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890672] ata1.00: status: { DRDY } [ 7.890724] ata1.00: failed command: READ FPDMA QUEUED [ 7.890781] ata1.00: cmd 60/78:10:e0:4f:61/00:00:02:00:00/40 tag 2 ncq 61440 in [ 7.890782] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890925] ata1.00: status: { DRDY } [ 7.890981] ata1: hard resetting link [ 8.208021] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 8.230100] ata1.00: configured for UDMA/133 [ 8.230124] ata1: EH complete Looks like the SATA interface tries to use 6Gbps link, then fails miserably and Linux fallbacks to 3Gbps. This is somewhat fine for me, as the system boots successfully each time and works under high load (cd linux-3.2.8; make -j16). I've also ran memtest86+ and it did not find any errors. What concerns me more is that Grub sometimes takes a long time to load the images and/or fails to load itself completely. The error is consistent and is probablistic: that is, each time I boot I have a certain chance to fail. Actually, I have a slight suspiction on the cause of the failure. Look at the cabling: What kind of engineer does it this way? Nah. Even 1Gbps Ethernet hardly tolerates cables bent over a small angle, and there you have 6Gbps SATA. How cound I determine and fix the cause of errors and/or switch the link to 3Gbps mode permanently?

  Read the article

• Slow ASP.NET site using IIS6

  - by lars

  Hi, I have two servers, one virtual and one physical, running the exact same site on both machines. Both machines are running on ~ 2% CPU load and very much RAM available for usage. Somehow the site, with cache turned off ofcourse, loads in ~ 500ms on the virtual machine (which is a dev-server by the way) but almost 3 full seconds on the physical machine. They're both running Server 2003, IIS6 aswell as asp.net version 2.0 Any ideas where I can start troubleshoot this? Best Regards LP

  Read the article

• Can't start apache in linux, because of proxy module

  - by Silmaril89

  When I try to start apache or run the command, httpd -M each fail and print the following error: httpd: Syntax error on line 137 of /etc/httpd/conf/httpd.conf: Syntax error on line 2 of /etc/httpd/conf.d/proxy_ajp.conf: Cannot load /etc/httpd/modules/mod_proxy_ajp.so into server: /etc/httpd/modules/mod_proxy_ajp.so: undefined symbol: proxy_module Any ideas on how to fix this? Thanks.

  Read the article

• MS Excel not installed after uninstalling Crystal Reports Viewer

  - by PowerUser

  I recently tried out the free Crystal Reports Viewer. I installed it on my work computer, but it didn't load (crashed on the EULA agreement of all places). After uninstalling the viewer, however, MS Excel 2003 does 3 things: "An error occurred initializing the VBA libraries (1004)" "Microsoft Excel has not been installed for the current user" Excel then closes. Did uninstalling the CR Viewer take some Microsoft DLLs with it? How do I get Excel working again?

  Read the article

• Traditional ASP.NET application in subdirectory of an MVC application

  - by David

  Windows Server 2003, IIS6. We're trying to deploy a non-MVC ASP.NET web application as a subdirectory of an MVC application. However the ASP.NET application in the subdirectory is failing with the message "Could not load file or assembly 'System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified." which is bizarre because it's not an MVC application.

  Read the article

• Windows Server 2008 Black Screen on boot

  - by Mark Milford

  Hi I have a windows server 2008 running in Parrallels (on Mac osx)... the mac crashed yesterday and so I hard rebooted it, when I fired up the Windows Server 2008 VM this morning it goes as far as the progress bar then goes black screen and does nothing else (even when left for a long time). I can boot into safe mode, Event Viewer says: "The following boot-start or system-start driver(s) failed to load: spldr stoflt" Any ideas? What should I do next?

  Read the article

• Trying to setup a PHP daemon using System_Daemon and I'm having issues getting it to run.

  - by yummm

  I get the following error when trying to start a daemon using Ubuntu 10.04 and the PHP5: PHP Warning: PHP Startup: Unable to load dynamic library 'usr/lib/php5/20060613/pcntl.so' - /usr/lib/php5/20060613/pcntl.so: cannot open shared object file: No such file or directory in Unknown on line 0 Does System_Daemon try to call pcntl? If so, why is it looking for the file where it does not exist?

  Read the article

• Best way to handle PHP sessions across Apache vhost wildcard domains

  - by joshholat

  I'm currently running a site that allows users to use custom domains (i.e. so instead of mysite.com/myaccount, they could have myaccount.com). They just change the A record of their domain and we then use a wildcard vhost on Apache to catch the requests from the custom domains. The setup is basically as seen below. The first vhost catches the mysite.com/myaccount requests and the second would be used for myaccount.com. As you can see, they have the exact same path and php cookie_domain. I've noticed some weird behavior surrounding the line below "#The line below me". When active, the custom domains get a new session_id every page load (that isn't the same as the non-custom domain session). However, when I comment that line out, the user keeps the same session_id on each page load, but that session_id is not the same as the one they'd see on a non-custom domain site either despite being completely on the same server. There is a sort of "hack" workaround involving redirecting the user to mysite.com/myaccount, getting the session ID, redirecting back to myaccount.com, and then using that ID on the myaccount.com. But that can get kind of messy (i.e. if the user logs out of mysite.com/myaccount, how does myaccount.com know?). For what it's worth, I'm using a database to manage the sessions (i.e. so there's no issues with being on different servers, etc, but that's irrelevant since we only use one server to handle all requests currently anyways). I'm fairly certain it is related to some sort of CSRF browser protection thing, but shouldn't it be smart enough to know it's on the same server? Note: These are subdomains, they're separate domains entirely (but on the same server). <VirtualHost *:80> DocumentRoot "/opt/local/www/mysite.com" ServerName mysite.local ErrorLog "/opt/local/apache2/logs/mysite.com-error.log" CustomLog "/opt/local/apache2/logs/mysite.com-access.log" common <Directory "/opt/local/www/mysite.com"> AllowOverride All #php_value session.save_path "/opt/local/www/mysite.com/sessions" php_value session.cookie_domain "mysite.local" php_value auto_prepend_file "/opt/local/www/mysite.com/core.php" </Directory> </VirtualHost> #Wildcard (custom domain) vhost <VirtualHost *:80> DocumentRoot "/opt/local/www/mysite.com" ServerName default ServerAlias * ErrorLog "/opt/local/apache2/logs/mysite.com-error.log" CustomLog "/opt/local/apache2/logs/mysite.com-access.log" common <Directory "/opt/local/www/mysite.com"> AllowOverride All #php_value session.save_path "/opt/local/www/mysite.com/sessions" # The line below me php_value session.cookie_domain "mysite.local" php_value auto_prepend_file "/opt/local/www/mysite.com/core.php" </Directory> </VirtualHost>

  Read the article

• Samba 'include' a per user config script

  - by cb0

  It is possible to use the include = /somepath/%u.smb.conf in the global section to call a script /somepath/cb0.smb.conf if the user cb0 connects to the samba server. Unfortunately this does not wotk for me because testparm alway gives me Can't find include file /somepath/.smb.conf When I connect to the server I can enter a username and pass but it alway rejects the connection. I'm using Samba Version 3.2.5 How can I achieve to load a custom user script depending on the user that is connecting ?

  Read the article

• Emacs23 with "window height too small"

  - by Willi Richert

  The new emacs23 gives me ("Window width 0 too small (after splitting)")) whenever I load ECB or tabbar. Seems to be introduces after updating from Kubuntu intrepid to jaunty. Any hint how to solve this?

  Read the article

• lacp, cicso 3550, 3560, help with configuration

  - by Flamewires

  Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Sendmail Tuning For Batch Mail Jobs

  - by Kyle Brandt

  I have a webservers that send out emails to a sendmail relay server as a batch job. The emails need to be accepted by the relay sendmail server as fast as possible, however, they do not need to go out (be relayed) very quickly. I am seeing a couple timeouts once and a while from the webserver trying to connect to the relay server. The load currently is about 30 emails a second for a couple minutes. There are quite a few tuning options for sendmail in the sendmail tuning guide. What I am focusing on now is the Delivery Mode: Delivery Mode There are a number of delivery modes that sendmail can operate in, set by the DeliveryMode ( d) configuration option. These modes specify how quickly mail will be delivered. Legal modes are: i deliver interactively (synchronously) b deliver in background (asynchronously) q queue only (don't deliver) d defer delivery attempts (don't deliver) There are tradeoffs. Mode i gives the sender the quickest feedback, but may slow down some mailers and is hardly ever necessary. Mode b delivers promptly but can cause large numbers of processes if you have a mailer that takes a long time to deliver a message. Mode q minimizes the load on your machine, but means that delivery may be delayed for up to the queue interval. Mode d is identical to mode q except that it also prevents lookups in maps including the -D flag from working during the initial queue phase; it is intended for ``dial on demand'' sites where DNS lookups might cost real money. Some simple error messages (e.g., host unknown during the SMTP protocol) will be delayed using this mode. Mode b is the usual default. If you run in mode q (queue only), d (defer), or b (deliver in background) sendmail will not expand aliases and follow .forward files upon initial receipt of the mail. This speeds up the response to RCPT commands. Mode i should not be used by the SMTP server. I currently have the CentOS default modes: Sendmail.cf: DeliveryMode=background Submit.cf: DeliveryMode=i Is sendmail.cf/mc for outgoing email from relay (to the intertubes) and sumbit.cf/mc for incoming eamil (from my webservers). Would it make sense to change the outgoing delivery mode to queue? If I did, what would the outbound email flow behave like? If this is the right thing to do, can anyone show me example mc configurations for this change? If it isn't, what recommendations are there for these constraints?

  Read the article

• Give me a sweet and simple XML viewer/editor for Windows

  - by Will

  I'm not talking about a full-weight and size editor. I'm talking about something better than Notepad and faster to load and less bloated than Visual Studio. Minimum requirements would be syntax highlighting.

  Read the article

• Why does my hackintosh freeze coming out of sleep?

  - by Dave

  I put OSx 10.1 on a Dell Mini 10v and everytime it goes to sleep, it either will not emerge from the sleep or if it does it's frozen. Is there something that I should be doing that I'm not? I went into the boot settings and it's set to load off of the Hard Disk drive and not the USB.

  Read the article

• NFS robustness or weaknesses

  - by Thomas

  I have 2 web servers with a load balancer in front of them. They both have mounted a nfs share, so that they can share some common files, like images uploaded from the cms and some run time generated files. Is nfs robust? Are there any specific weaknesses I should now about? I know it does not support file locking but that does not matter to me. I use memcache to emulate file locking for the runtime generated files. Thanks

  Read the article

• SQL Server 2012 Read-Only Replica physical requirements

  - by Ddono25

  We are going to be setting up two replicas of our DataMart and related databases, and our plan includes using Hyper-V VM's to handle the load. When creating the VM's, we cannot find specific requirements or recommendations for RAM/CPU power for read-only replicas. Our current Primary DataMart setup has 64GB RAM and Two Quad-Core procs, which so far has been adequate for our usage. What should be the server setup for replicas and SQL Server to adequately support the read-only usage?

  Read the article

• svnserve vs xinetd + svnserve

  - by crazybyte

  What would be the best solution considering, scalability/load and security, svnserve + xinetd or standalone svnserver? Thank you!

  Read the article

• How to set up linux watchdog daemon with Intel 6300esb

  - by ACiD GRiM

  I've been searching for this on Google for sometime now and I have yet to find proper documentation on how to connect the kernel driver for my 6300esb watchdog timer to /dev/watchdog and ensure that watchdog daemon is keeping it alive. I am using RHEL compatible Scientific Linux 6.3 in a KVM virtual machine by the way Below is everything I've tried so far: dmesg|grep 6300 i6300ESB timer: Intel 6300ESB WatchDog Timer Driver v0.04 i6300ESB timer: initialized (0xffffc900008b8000). heartbeat=30 sec (nowayout=0) | ll /dev/watchdog crw-rw----. 1 root root 10, 130 Sep 22 22:25 /dev/watchdog | /etc/watchdog.conf #ping = 172.31.14.1 #ping = 172.26.1.255 #interface = eth0 file = /var/log/messages #change = 1407 # Uncomment to enable test. Setting one of these values to '0' disables it. # These values will hopefully never reboot your machine during normal use # (if your machine is really hung, the loadavg will go much higher than 25) max-load-1 = 24 max-load-5 = 18 max-load-15 = 12 # Note that this is the number of pages! # To get the real size, check how large the pagesize is on your machine. #min-memory = 1 #repair-binary = /usr/sbin/repair #test-binary = #test-timeout = watchdog-device = /dev/watchdog # Defaults compiled into the binary #temperature-device = #max-temperature = 120 # Defaults compiled into the binary #admin = root interval = 10 #logtick = 1 # This greatly decreases the chance that watchdog won't be scheduled before # your machine is really loaded realtime = yes priority = 1 # Check if syslogd is still running by enabling the following line #pidfile = /var/run/syslogd.pid Now maybe I'm not testing it correctly, but I would expecting that stopping the watchdog service would cause the /dev/watchdog to time out after 30 seconds and I should see the host reboot, however this does not happen. Also, here is my config for the KVM vm <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit sl6template or other application using the libvirt API. --> <domain type='kvm'> <name>sl6template</name> <uuid>960d0ac2-2e6a-5efa-87a3-6bb779e15b6a</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>Westmere</model> <vendor>Intel</vendor> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='ds'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='vme'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='rdtscp'/> <feature policy='require' name='ht'/> <feature policy='require' name='dca'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='pdpe1gb'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='pclmuldq'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='require' name='aes'/> </cpu> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/mnt/data/vms/sl6template.img'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> <controller type='usb' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/> </controller> <interface type='bridge'> <mac address='52:54:00:44:57:f6'/> <source bridge='br0.2'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:88:0f:42'/> <source bridge='br1'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <watchdog model='i6300esb' action='reset'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </watchdog> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain> Any help is appreciated as the most I've found are patches to kvm and general softdog documentation or IPMI watchdog answers.

  Read the article

• Windows File Server -- Where To Start

  - by yodie

  I have a Windows 2003 server, a whole load of PDFs on it that need to be accessed from various computers, both on the local network and not, and including mobile devices, and files that have to be sent to it. Where do I start? The most important thing (after getting the job done) is security.

  Read the article

• Playing HD video accelerated by GPU? (Linux)

  - by data_jepp

  I know that this laptop (Asus UL30A) does support playing HD material with the help of the GPU on windows. The question is how can I do this under linux? The CPU load as is implies that this is not activated. I assume that it's limited to a handful of codecs. But which player supports this, if its even supported at all?

  Read the article

• Automatic start of Tomcat on server restart (Linux)

  - by Nick

  I have 4 Tomcat instances I wish to start when the server (Cent OS 2.6.9) restarts. After all other services have started I would like to start these up - but I am a bit worried about the load of starting all 4 at the same time, so maybe a short delay would be necessary. How should I go about this?

  Read the article

• VMWARE WORKSTATION terrible performance on local hard disk

  - by Captain Kidd

  I'm working on vmwaer image files. My computer always load hard disk and vmware works very slow at the same time. Guest operation system: WindowsXP SP2 Host operation system: WindowsXP sp2 Is there any way can improve the performance?

  Read the article

• Site not loading when www is left out of the URL

  - by Etienne

  Why does my website not load if I type: example.com But it does work when I type: www.example.com Is this a setting in IIS? We are using ASP.NET 3.5 with a SQL Server database. Thanks in advanced!

  Read the article

• Lag spikes at full CPU usage, maybe video card

  - by Roberts

  I am posting this thread in hurry so few things may be missed (I will update tomorrow). My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can).

  Read the article

< Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >