Search Results

Search found 13950 results on 558 pages for 'durable services'.

Page 291/558 | < Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >

  • remote telnet and email

    - by Mustafa Ismail Mustafa
    This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

    Read the article

  • Dependency issue installing PostGIS on CentOs 6.3

    - by Nyxynyx
    I am new to linux and is trying to install PostGIS2 after successfully installing PostgreSQL 9.1. The machine is running CentOS 6.3 and has cPanel installed. Problem: When I tried installing PostGIS using yum: yum install postgis2_91 postgis2_91-utils, I get the dependency error below. How should I solve this dependency problem and install PostGIS? Thank you so much! --> Finished Dependency Resolution Error: Package: postgis2_91-utils-2.0.1-1.rhel6.i686 (pgdg91) Requires: perl-DBD-Pg Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdapserver.so.7 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdap.so.11 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libgeotiff.so.1.2 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libnetcdf.so.6 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libdapclient.so.3 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libhdf5.so.6 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: librx.so.0 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libogdi.so.3 Error: Package: gdal-1.7.2-1.el6.i686 (pgdg91) Requires: libcfitsio.so.0 You could try using --skip-broken to work around the problem ** Found 6 pre-existing rpmdb problem(s), 'yum check' output follows: bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) exim-4.77-1.i386 has missing requires of perl(SafeFile) frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 sendmail-cf-8.14.4-8.el6.noarch has missing requires of sendmail = ('0', '8.14.4', '8.el6') Update An error still remains: Error: Package: postgis2_91-utils-2.0.1-1.rhel6.i686 (pgdg91) Requires: perl-DBD-Pg You could try using --skip-broken to work around the problem ** Found 6 pre-existing rpmdb problem(s), 'yum check' output follows: bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) exim-4.77-1.i386 has missing requires of perl(SafeFile) frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 sendmail-cf-8.14.4-8.el6.noarch has missing requires of sendmail = ('0', '8.14.4', '8.el6')

    Read the article

  • PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded

    - by Tiny
    I'm trying to upgrade php 5.4.14 from php 5.4.3 in wamp server 2.2e. I have downloaded php-5.4.14-Win32-VC9-x86 (thread safe). Extracted it under C:\wamp\bin\php. Copied wampserver.conf from C:\wamp\bin\php\php5.4.3 to C:\wamp\bin\php\php5.4.14. Renamed php.ini-development to phpForApache.ini. -The port number the wamp server has been changed in the http.conf file to 8087 from its default 80. This is mentioned here though it is about upgrading from php 5.3.5 to php 5.4.0. After this, Restarting of the wamp server and services all over again has all been done and those two versions appeared in the menu php-versions (which is opened when the icon of the server is clicked). But when I attempt to enable a library like php_mysql or php_mysqli, a warning message box appears. PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded. I have also tried to removing the semicolon before them in the php.ini file but to no avail. I'm running Microsoft Windows XP Professional Version 2002, service pack 3. Where might be the problem? EDIT: I have changed extension_dir from C:\php to c:\wamp\bin\php\php5.4.14\ext\ in php.ini as the answer below indicates and the library is now loaded correctly but it says, 1045 - Access denied for user 'root'@'localhost' (using password: YES) though the user name and the password are the same as they are in MySQL in the config.inc.php file under phpmyadmin. I have also tried to restart MySQL56 service from Control Panel-Services(Local) but it keeps giving the same error. Does someone know why this happens?

    Read the article

  • How to collect the performance data of a server during an unreachable/down period using Nagios?

    - by gsc-frank
    Some time services and host stop responding due to a poor server performance. I mean, if for some reason (could be lot of concurrency services access, a expensive backup execution on the server or whatever that consume tons of server resources) a server performance is very degraded, that could lead that the server isn't capable to establish any "normal network communication" (without trigger whatever standards timeouts defined for such communication). Knowing host's performance data (cpu, memory, ...) in case of available during that period (host is not down and despite of its performance degradation still allow plugins collect performance data) could be very useful for sysadmin to try to determine what cause the problem, or at least, if the host performance was good and don't interfered at all in the host/service down. This problem could be solved using remote active (NRPE) or remote passive (NSCA) if such remote solutions could store (buffered) perf data to be send to central Nagios server when host performance or network outage allow it. I read the doc of both solutions and can't find any reference to such buffer mechanism neither what happened in case that NSCA can't reach Nagios server. Any idea of how solve this lack of info? so useful for forensic analysis. EDIT: My questions isn about which tools I can use to debug perf problems or gather perf data to analysis, but is about how collect (using Nagios) host perf data even during a network outage for its posterior analysis (kind of forensic analysis). The idea is integrate such data to Nagios graphers like pnp4nagios and NagiosGrapther. I know that I could install tools like Cacti in each of my host, and have a kind of performance data collection redundancy, but I really want avoid that and try to solve all perf analysis requirements with one tools: Nagios

    Read the article

  • Exchange DEAD! Server recovered but no users can log in

    - by erotsppa
    Yesterday we had a hardware failure and brought our exchange server down. The hardware was repaired and the server was brought back up. Windows server 2008 did the disk check upon bootup and everything was recovered. However, no users can log into their exchange account! This is true with IMAP, Exchange and OWA! All three of them, refused to accept any users. For example when I try to access OWA, I get the following page http://pastie.org/584061 We verified that all the services are up (IMAP, POP, SMTP, IIS etc). We were able to connect to all those services with their respective ports through telnet. What could be the problem? It looks like the database cannot be mounted, from Exchange management console, when I try to mount the database it gives: Microsoft Exchange Error Failed to mount database 'Mailbox Database'. Mailbox Database Failed Error: Exchange is unable to mount the database that you specified. Specified database: SERVER\First Storage Group\Mailbox Database; Error code: MapiExceptionCallFailed: Unable to mount database. (hr=0x80004005, ec=-528) . I read online that there is a repair utility, so I tried it. I navigated to my edb file and ran eseutil /p "Mailbox Database.edb". It printed the following output *Repair completed. Database corruption has been repaired! Note: It is recommended that you immediately perform a full backup of this database. If you restore a backup made before the repair, the database will be rolled back to the state it was in at the time of that backup. Operation completed successfully with 595 (JET_wrnDatabaseRepaired, Database cor ruption has been repaired) after 885.750 seconds.* However I am still unable to mount!

    Read the article

  • How does enterprise failover, such as with google.com, actually work?

    - by Alex Regan
    We have a few fedora systems that are configured for web, FTP, and email services. We'd like to mirror these services, so that we can provide near 100% reliability for our users. I'm a fairly experienced Linux administrator, but don't have much experience with redundant systems. What is the best way to do this? How does google and amazon do it? Google.com resolves to multiple IP addresses, but if my local desktop caches one of the IPs that are unreachable, I'm going to get a failed connection message. How do they prevent that from happening? If one of their servers goes down, how is it automatically redirected to another system, without the end-user ever knowing it? I understand there are failover devices, but they're only for failing over the system itself, not a complete network. Let's say we have the worst-case scenario, such as my primary system becomes inaccessible. What are the fundamental components that are used on Linux systems to provide this capability? I'm looking for concepts, or approaches, not answers like "check out openstack". What are the actual pieces that make up the solution? What has to be done to implement this capability? Hopefully my question is clear. I'd like to know what the pieces are that make up a failover system and what approach is taken by successful organizations that implement it. Thanks again, Alex

    Read the article

  • Windows 2008 R2 remote desktop - Double Login

    - by Zulgrib
    After an Active Directory fail RDP connection started to ask for credentials twice (once on local RDP program, second time on remote's logon screen) I already looked at Windows 2008 R2 RDS - Double Login Solution provided there doesn't work for me. The server is alone, without AD/DNS services, RDP service isn't installed I tried every security settings on RDP-Tcp (RDP, Negotiate, SLL) Logon option is set to "Use credentials from the client" Both windows client and server use RDP 7.1 fPromptForPassword regitries are set to 0 Local Computer Policy\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Security\Always prompt for password upon connection is set to "Disabled" Why i am sure the problem comes from the server and not the client ? This problem affected a 3rd RDP program on Android too (it was directly showing "preparing desktop previously, on both MS RDP and the 3rd program) No bakcup are available (Else the Active Directory wouldn't be a fail, but just a lose of time) I am wondering if a rule linked to RDP got changed after the AD install+unistall, but i'm unable to find where. While this is not a critic problem, this is very annoying. I don't know if more information are needed, if it's the case and if you are patient enough, please tell me what is missing and i'll edit this post to add the missing informations.

    Read the article

  • Domino to Exchange 2007 (or 2010) Design Concerns?

    - by NickToyota
    Today we got the executive green light to proceed with changing from a Domino platform to Exchange. The business prefers Exchange for a messaging platform. (even though IMO IBM Domino is fine - if it aint broke, don't fix it but it was not my call). I have been put in charge of Domino to Exchange process goes smoothly as possible. I have also been told to put together costs for this project. I have some questions and concerns re: network design, licensing, costs: The current setup is as follows. 1 HQ office (100 users), 1 secondary office (50 users), 5 branch offices (under 10 users). 5 different email domains Windows Server 2003 functional level with a few 2008 R2 Servers Lotus Domino Notes Servers (one in each office) Ironmail Appliance Public Domino Web Mail server Majority G5+ Proliant Servers Domino Blackberry Enterprise license and server No VoIP phones What are the basic hardware requirements for Exchange 2007 or 2010? Can I simply purchase a single physical server? Will each office require an Exchange server or possibly additional servers (roles)? How is email routed to the smaller branch offices? Standard or Enterprise licenses? The business has been running Domino (messaging and application services) for over 10 years and also want Exchange to support email services, Blackberry, Outlook Web Access, possibly support for iPhone devices. Thank you Serverfault universe.

    Read the article

  • Server 2008 R2 DNS Lockup / Stops Resolving Internet Names

    - by Richard Maynard
    We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed

    Read the article

  • SQL Server Installaion error 0x84B40000

    - by Kurtevich
    I have a problem installing SQL Server 2008 R2. Long time ago I had it installed, and then uninstalled. It was left in "Add/remove programs", but I didn't pay attention on that. I had 2005 installed. And now there is a need to install 2008. I removed 2005 and started installing 2008, but it says that space on C: is not enough. That's when I found out that "Add/remove programs" shows it occupying more than 4 gigabytes, though I used to uninstall it. So I click "Remove", it shows all those many screens and validations, shows that removal completed, but the size of Program Files folder is still more than 4 GB. I removed (from "Add\remove programs" everything that had "SQL Server" in it's name, but that main "SQL Server 2008" item is still there and still 4 GB and uninstalling does nothing. Because installation of SQL Server did not show existing instances, and I don't see any running services related to SQL server (well, almost any, more details in the end), I though that this folder contains just some leftover staff and data and deleted it manually. Then agreed to removing of the item in "Add/remove programs" and everything looks clean. Now every time I try to install SQL Server (even in the minimum configuration), I receive the following error: SQL Server Setup has encountered the following error: The specified credentials that were provided for the SQL Server service are not valid. To continue, provide a valid account and password for the SQL Server service. Error code 0x84B40000. What is this service mentioned here? This error looks like I'm trying to add features to existing server and it can't login. But the setup didn't ask me for any credentials, except one username that couldn't be changed. Here are the services shown that can be related, both disabled and pointing to non-existing executables: SQL Active Directory Helper Service SQL Full-text Filter Daemon Launcher (MSSQLSERVER) I understand that this must be because of my manual deletion, but is there a way to clean it up now?

    Read the article

  • Enabling AHCI in BIOS for SSD

    - by Robert
    I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

    Read the article

  • Windows 2008 RemoteAPP client disconnects within a matter of minutes.

    - by Jeroen Wilke
    I'm having an odd problem with Windows 2008 TS, and remote applications specifically. The situation is as follows: TS idle timeout is disabled via GPO TS terminating disconnected sessions after 1hr (via GPO) My users can log on to the Terminal server, and get a full desktop, OR via rdp files that give access to a few remote applications. When a user connects to a full desktop, everything is fine and dandy, they will remain logged on indefinately, and when they disconnect the session is terminated after an hour. however, when a user connects using a remote application link, the client seems to disconnect after only a few minutes of inactivity, when you click the window, the session reconnects. EventID's on TS server: 4779: This event is generated when a user disconnects from an existing Terminal Services session, or when a user switches away from an existing destop using Fast User Switching. 4778 : This event is generated when a user reconnects to an existing Terminal Services session, or when a user switches to an existing desktop using Fast User Switching users are connecting directly to 3389, not using a TS-gateway at the moment. This behavior is consistent on different clients that we have, Full desktop is fine, RemoteAPP constantly disconnects. The .rdp file used doesn't list any interesting parameters, aside from what application to launch, and where to find it. Can someone explain to me how there can be a difference in behaviour between full desktop, and remoteapp ? since essentially they use the exact same client ? Regards Jeroen

    Read the article

  • Kerberos service on win2k dc will not start following disk failure

    - by iwilson68
    Hi, I have a win2k (mixed mode domain) with 4 DCS. One of these also acts an exchange 2000 server which uses 2 logical volumes from an MSA 2000 array. AD etc is stored on local drives. We experienced a problem last week when the raid array fell back to a redundant controller and this temporarily meant that the two logical drives were not visible to the server for around 5 minutes and a couple of reboots. The log records these Events as Type: Warning Event Source: Disk Event Category: None Event ID: 51 Date: 06/11/2009 Time: 11:46:23 User: N/A Computer: server1 Description: An error was detected on device \Device\Harddisk1\DR1 during a paging operation. Following these problems, the server “kerberos Key Distribution” service refuses to start with an “error.31 a device attached to the system is not functioning”. All other automatic start services (including net logon) are running and there are no DNS issues etc. All devices are also functioning but the two logical MSA disks are now numbered in the Windows Disk Management MMC as 2 and 4 and I suspect that they may have previously been identified as disks 1 & 2 and perhaps windows still sees this as an ongoing failure?? Replication has not been affected but obviously there are many audit failures in the security log relating to users and workstations presumably linked to the Kerberos issue. Attempting to manually start the kerberos service generates the following in the System Log. Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 09/11/2009 Time: 09:46:55 User: N/A Computer: Server1 Description: The Kerberos Key Distribution Center service terminated with the following error: A device attached to the system is not functioning. DCDIAG passes all tests except “Advertising” and “Services” which I believe relate directly to the failure of Kerberos only. Any advice would be appreciated.

    Read the article

  • Do you need to advertise an AFP service via Avahi for an Ubuntu Server to show up in OSX Finder?

    - by James
    I am only advertising an NFS share plus the "model", and I don't want to install extra services on the Server unless I have to, ie netatalk, as it is used solely for NFS exports. Currently there is no entry in Finder under "Shared" with below config of Avahi. serveradmin@FILESERVER:/etc/avahi/services$ cat nfs.service <?xml version="1.0" standalone='no'?><!--*-nxml-*--> <!DOCTYPE service-group SYSTEM "avahi-service.dtd"> <service-group> <name replace-wildcards="yes">%h</name> <service> <type>_nfs._tcp</type> <port>2049</port> <txt-record>path=/Volumes/StoragePool</txt-record> </service> <service> <type>_device-info._tcp</type> <port>0</port> <txt-record>model=Xserve</txt-record> </service> </service-group> Server: Ubuntu 12.04.01 x64 Clients: OSX 10.6.8 , 10.7.5, 10.8.2 The goal is to advertise that NFS share, then assign a really old Model code of Mac like a Powermac and switch out the icon for a more "LinuxServer-y" one. Plus allow users to connect to NFS in a manner they are familiar with like our other Xserve servers. I think Avahi is working in general as if I do: nfs://FILESERVER.local/Volumes/StoragePool it will connect fine. Any ideas?

    Read the article

  • TeamCity sends inadequate responses after Selenium tests

    - by Dmitriy Sukharev
    I have a TeamCity 7.0.2 at CentOS 6.2 server without X Server. I've installed x11-fonts*, xvfb, firefox, xauth, extracted env. variable DISPLAY=localhost:1, and started xvfb. After that I could start Selenium tests using maven. Tests are executed, but there's an issue with TeamCity. Usually TeamCity starts hehaves absolutely inadequate (it confuses images at the page, sends xml or strange text ampersants and numbers in responses and is a bit slower), also tests are executed 4 times slower (1h 15m) at server than at tester Windows 7-based machine (25m). It worth to notice that tests launch two Jetty servers for tested application (one for REST-services application and another for client). In TeamCity I set JVM command line parameters: -Xms256m -Xmx1224m -XX:MaxPermSize=320m, and Additional Maven command line parameters ends with "-DMAVEN_OPTS=-Xmx1024m" (without quotes). Also both web-services and TeamCity uses the same Oracle server (but different Oracle users). Finally TeamCity and its build agent is at the same server. Server has only 4GB of RAM, but during testing there're 400MB of RAM and 1.2GB of swap. TeamCity and Firefox uses about 65% of CPU during testing. There's no firefox process after end of testing. My knowledge about Selenium is weak. I only know that we use 2.20.0 version of selenium-java maven dependency. Please help me to determine why TeamCity sends wrong responces after Selenium tests. I've tried to give you all information I have, but feel free to ask me for more information.

    Read the article

  • How to solve SocketException: Permission denied: connect

    - by luxinxian
    I recently encountered a problem that is giving me a headache and I need help ... The System consists of two subsystems, called A and B, each running on a standalone Tomcat instance and currently running on the same machine. A invokes B's service via Spring httpInvoker (i.e. over HTTP). B system also invokes the other system's services via HTTP. Symptoms: the system starts to run and appears to work normally for around 10-15 days; the system will run for a period of time after an exception: org.springframework.remoting.RemoteAccessException: Could not access HTTP invoker remote service at [http://xxx.xxx.xxx.xxx/remoting/call]; The nested exception is java. net.SocketException: **Permission denied: connect** when the exception occurs, the system continues. This happens always, not only occasionally. (It looks like some resources are exhausted, but CPU rate < 5%, memory < 15%, network < 5%). when the system call between A and B fails, the B system call over HTTP to an external service also failed, with the same exception. Restarting both Tomcat services makes the whole system work properly. So repeatedly following steps 1 - 5, I have not found the root reason. Environment: windows 2008 R2 tomcat7.0.42 x86_64 oralce-jdk-1.7.0_40 Any ideas?

    Read the article

  • RemoteApp .rdp embed creds?

    - by Chris_K
    Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

    Read the article

  • QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

    - by Horst Walter
    On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

    Read the article

  • Ho can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

    - by jjr2527
    I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

    Read the article

  • OSX Server 10.5 - Cannot log into Workgroup Manager - diradmin password is correct

    - by Mister IT Guru
    I've got a setup where I am trying to rescue a broken AD. We can no longer authenticate on the Workgroup manager, with passwords being rejected all the time - even though it is correct. I can connect using the workgroup manager on another server and I get the user list as expected, but when I click the padlock to make changes, I get the following screen: The problem is, I know the password is correct, I just used it to connect to the server in the first place. I can log into the server using the local admin, and services such as AFP, VPN and SMB continue to serve users. I have about 300 or so users on this server, and I would very much like to avoid having a rebuild. As there is much configuration that has been done without my knowledge (it's a client machine), I'd like to attempt to fix it, and then create another server and migration OD off this broken machine, then decommission it "gently". Ultimately this would mean no disruption of services. What I'd like it some tips as to how to fix the problem with authenticating to make changes in the work group manager, and maintenance on open directory in general. Thanks

    Read the article

  • KVM guest VLAN aware problems

    - by baraka
    Hi, We are using Centos 5.5. as KVM host. It has two nics. One for management and the other one for services. As we have services in multiple vlans this nic is configured as a 802.1Q trunk. Any VM must be able to have access to any vlan, so host trunk interface is bridged to its tap interface and vlan is configured inside VM. Everything works fine while there is not heavy traffic. I can not find any log on guest or host, but, after some certain sustained big file transfer (about 6Gb) bridging stop working. Other guest on the same host continue working without problems. tcpdump on bridge interface is Ok, but on guest tap inferface I can see only outgoing traffic. Restarting bridge or rejoining tap interface doesn't provide any clue. Rebooting guest turns on bridge again. Bridge configuration is minimal: just addbr and addif (no stp). Any idea welcome!

    Read the article

  • Optimum configuration of McAfee for Servers

    - by Wayne Arthurton
    Our corporate standard is McAfee Enterprise, unfortunately this is non-negotiable. On two types of servers I'm responsible for, SQL & Web, we have noticed major performance issues with the corporate standard setup. Max scan time 45sec One policy for all processes Scan ALL files on write, read and open for backup Heuristics: Find unknown programs, trojans and macros Detect unwanted programs Exclude: EVT, LDF, LOG, MDF, VMD, , windows file protection) This of course still causes major slowdowns. IIS .NET recompiles are slow especially with SharePoint, SQL backups and restores, SQL Analysis Services, Integration Services and temp data from them as well. I have looked from time to time, for some best practices on setting up McAfee of SQL & SQL Analysis Service, SQL Integration Service, Visual Studio, Sharepoint, and .NET web servers in general. How do people setup McAfee enterprise on their corporate serves keeping security intact, but affecting performance as minimally as possible? Has anyone run across white papers on these setups? Obviously some are case by case, but there must be some best practices out there somewhere.

    Read the article

  • OpenLDAP Authentication UID vs CN issues

    - by user145457
    I'm having trouble authenticating services using uid for authentication, which I thought was the standard method for authentication on the user. So basically, my users are added in ldap like this: # jsmith, Users, example.com dn: uid=jsmith,ou=Users,dc=example,dc=com uidNumber: 10003 loginShell: /bin/bash sn: Smith mail: [email protected] homeDirectory: /home/jsmith displayName: John Smith givenName: John uid: jsmith gecos: John Smith gidNumber: 10000 cn: John Smith title: System Administrator But when I try to authenticate using typical webapps or services like this: jsmith password I get: ldapsearch -x -h ldap.example.com -D "cn=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" Enter LDAP Password: ldap_bind: Invalid credentials (49) But if I use: ldapsearch -x -h ldap.example.com -D "uid=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" It works. HOWEVER...most webapps and authentication methods seem to use another method. So on a webapp I'm using, unless I specify the user as: uid=smith,ou=users,dc=example,dc=com Nothing works. In the webapp I just need users to put: jsmith in the user field. Keep in mind my ldap is using the "new" cn=config method of storing settings. So if someone has an obvious ldif I'm missing please provide. Let me know if you need further info. This is openldap on ubuntu 12.04. Thanks, Dave

    Read the article

  • XP Client for NFS failure dialog on startup, but drive mapping works

    - by Matt Bennett
    I'm mounting an NFS share to some windows machines using the tools that come in the Services for UNIX Administration toolkit. I've set up the User Name Mapping service to use local passwd and group files. I had to manually start the User Name Mapping service, and then created an 'advanced map' from the XP machine's user to a uid that exists in on my NFS server, like so: Windows User: Matt Bennett UNIX Domain: PCNFS UNIX User: mattbennett UID: 10250 Primary: * I can map a network drive without any issues, and it correctly identifies the UID and GID to use, but when I reboot I get this message: "An error occurred while connecting to the NFS server. Make sure that the Client for NFS service has started. If the problem persists make sure Client for NFS service can communicate with User Name Mapping or PCNFS server." After dismissing the dialog, the machine finishes booting and the network drive is there in My Computer with the title "Disconnected Network Drive", but I can open it I can see the network share without a problem, and then it drops the 'disconnected' from its title. It seems like the services are starting in the wrong order or something, so the first attempt to connect fails but subsequent ones work as expected. There don't seem to be any symptoms apart from the dialog box, but obviously something's not quite right. What have I done wrong? Thanks, Matt.

    Read the article

  • How can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

    - by jjr2527
    I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

    Read the article

< Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >