Search Results

Search found 15780 results on 632 pages for 'pass board elections 2011'.

Page 294/632 | < Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >

  • Why do Ping and Dig provide different IP address than nslookup?

    - by user1032531
    When pinging my domain name which points to my home public IP from two different servers on my LAN, it shows them pinging different IP. Further investigation shows dig and nslookup providing different results. See below. A little history. My IP used to be 11.22.33.444 and is hosted by Comcast. I changed routers, and it somehow got changed to 55.66.77.888. I've since updated my 1and1 domain name to point to the 55.66.77.888. desktop is a basic server, runs the web server, and connects wirelessly to my LAN. laptop is a GUI and connected via CAT5. Both operate Centos6.4. My old router was a D-Link, and used their "Virtual Server" feature to pass port 80 to desktop. My new router is a Linksys, and I use their "Port Forwarding" feature to pass port 80 to desktop (however, I haven't gotten this part working yet). What is going on??? Why the different IPs? Obviously, it most somehow be stored on the server, but why does the actual machine even know the public IP since it is on a LAN? How do I purge the old IP? [root@desktop etc]# dig +short myDomain.com 11.22.33.444 [root@desktop etc]# nslookup www.myDomain.com Server: 8.8.8.8 Address: 8.8.8.8#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@desktop etc]# dig myDomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.6 <<>> myDomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 13822 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myDomain.com. IN A ;; ANSWER SECTION: myDomain.com. 16031 IN A 11.22.33.444 ;; Query time: 21 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Mon Oct 21 04:36:52 2013 ;; MSG SIZE rcvd: 44 [root@desktop etc]# [root@laptop ~]# dig +short myDomain.com 55.66.77.888 [root@laptop ~]# nslookup www.myDomain.com Server: 192.168.0.1 Address: 192.168.0.1#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@laptop ~]#

    Read the article

  • Optical multicast

    - by Randomblue
    I have a 10G XPF+ optical cable with market updates from a stock exchange. This cable goes into a switch, which then multicasts every packet to a couple of computers. The problem with using a switch for multicast is that there is latency overhead, even with a pass-through switch (~200ns). Are there "optical" solutions (I'm thinking of a beam splitter of some sort) which would allow for close to zero latency 10G multicast?

    Read the article

  • Update to recent stable php in Ubuntu 12.04

    - by Jurian Sluiman
    We run an Ubuntu 12.04 server where php 5.3.10 is installed by default. I thought Ubuntu did only apply bugfixes in their updates, so micros like 5.3.x should pass through. Apparently, our version isn't updated, but we are stuck with a critical bug in php which is solved in 5.3.15. Should I wait longer for this release to bubble up? Or are there safe repositories to use for Ubuntu to continuously update php and php related packages?

    Read the article

  • OSX Samba Server

    - by Chris Maness
    Hello I have a MacPro that I'm using as a local file server. I mapped a directory on the secondary hard drive of the MacPro as a drive on our local Windows box. It worked fine for about a week and then suddenly stopped working. The windows computer gives the error that it's an invalid username and password however I have checked and double checked to ensure that the user and pass are correct to no avail. Anyone have any ideas on what's going on here?

    Read the article

  • Again WPA Connection problem even after changed to latest version ..please help

    - by Renjith G
    I am using hostapd, wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board with linux and my desktop PC, Windows XP SP2 (with Olitec USB wireless) are fine. But when I configured the WPA type, the connection seems established but shows the status "TKIP - Key Absent" in the security dialog box. Anyone faced this problem? Am attaching the conf files and the connection status. In the AP side am complaining . I am using the in built radius server conf with the hostapd 0.4.7 hostapd.conf interface=ath0 driver=madwifi logger_syslog=0 logger_syslog_level=0 logger_stdout=0 logger_stdout_level=0 debug=0 eapol_key_index_workaround=1 dump_file=/tmp/hostapd.dump.0.0 ssid=Renjith G wpa wpa=1 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-EAP wpa_pairwise=TKIP CCMP wpa_group_rekey=600 macaddr_acl=2 /* commented */ ieee8021x=1 /* commented */ eap_authenticator=1 own_ip_addr=172.16.25.1 nas_identifier=renjithg.com auth_server_addr=172.16.25.1 auth_server_port=1812 auth_server_shared_secret=key1 ca_cert=/flash1/ca.crt server_cert=/flash1/server.crt eap_user_file=/etc/hostapd.eap_user hostapd.eap_user "*@renjithg.com" TLS And the commands am using are wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid Renjith channel 6 ifconfig ath0 192.168.25.1 netmask 255.255.255.0 up hostapd -ddd /etc/hostapd.conf Please correct if am wrong .. Also am getting the debug messages on my AP when am connecting in my windows machine through WPA ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf Configuration file: /etc/hostapd.conf Line 18: obsolete eap_authenticator used; this has been renamed to eap_server madwifi_set_iface_flags: dev_up=0 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'Renjith G wpa' madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA= 0x1 madwifi_set_iface_flags: dev_up=1 madwifi_set_privacy: enabled=1 WPA: group state machine entering state GTK_INIT GMK - hexdump(len=32): 9c 77 cd 38 5a 60 3b 16 8a 22 90 e8 65 b3 c2 86 40 5c be c3 dd 84 3e df 58 1d 16 61 1d 13 d1 f2 GTK - hexdump(len=32): 02 78 d7 d3 5d 15 e3 89 9c 62 a8 fe 8a 0f 40 28 ba dc cd bc 07 f4 59 88 1c 08 84 2b 49 3d e2 32 WPA: group state machine entering state SETKEYSDONE madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 Deauthenticate all stations l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 < Register Fail < Register Fail Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 NOW am getting the following error message with latest tools. *This is the latest error messages..please refer this only..* ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf TLS: Trusted root certificate(s) loaded madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'RenjithGwpa' SSID - hexdump_ascii(len=11): 52 65 6e 6a 69 74 68 47 77 70 61 RenjithGwpa PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): a6 55 3e 76 94 8b d9 81 a1 22 5e 24 29 83 33 86 11 a8 7e 93 19 7c a9 ab ab cc 12 58 37 e5 35 b6 RADIUS local address: 172.16.25.1:1024 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=24 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09

    Read the article

  • View Remote Desktop access logs on Win 2003

    - by NealWalters
    Is there a history log of each use of Remote Desktop. I'd like to view and audit IP addresses. I'm running a dedicated server hosted by a web hosting company. Had some problems recently, and trying to validate if anyone besides me actually logged on (i.e. if user/pass is compromised). Thanks, Neal Walters

    Read the article

  • Hosting multiple email domains on single server

    - by sharjeel
    Is it practically possible to host multiple email domains on a single machine with single IP address? Considering that spam filters do RDNS and in that case one IP address may host only one domain to pass the spam filters. If not, how does the hosted email work? Do they have get a separate IP address for each domain's email they host?

    Read the article

  • System shuts down immediately after few sconds

    - by Anil
    I have a computer with following specification and was working fine after re-installing the system and refitting sink fan unit. Recently it shuts down automatically after a few seconds. I checked PSU by shorting pin no.s 13 & 14 as well as 14 & 15. It worked well means the PSU fan moves. But I never checked the voltages at different wires. I refitted the heat sink fan by applying thermal paste. but it behaved the same. Again I refitted the Heat Sink Fan, then it worked for 2 minutes and again shut down. Now it shuts down immediately after switching on. Mother board : M26GTM-3VP CPU : AMD athlon PSU : 450 watt Can anyone help?

    Read the article

  • Sound does not work on the administrator profile.Works on a non-administrator profile on Windows XP

    - by Sharjeel Sayed
    Initially I suspected a missing driver, but then sound ( for movies,songs etc ) works fine on the other non-administrator account, but does not work when I log in to the Administrator account. And yes..I have checked the sound volume and mute status as well. Details of my system OS: Windows XP Professional Service Pack 3 (build 2600) Processor: 2.00 gigahertz AMD Athlon 64 Memory: 448 Megabytes Usable Installed Memory Board: ASUSTeK Computer Inc. K8V-MX Bus Clock: 200 megahertz BIOS: American Megatrends Inc. 0112 07/18/2005 Multimedia: SoundMAX Integrated Digital Audio Any help would be appreciated.Thanks in advance

    Read the article

  • When connecting to a unix box, how does it know you have SSH setup on your desktop?

    - by Blankman
    When you use something like putty to connect to a linux box, and you setup your SSH keys etc. When connecting, how does it tell the server that you want to connect using your SSH keys? Is SSH running as a service on a particular port or does it simply pass your private-key and then the login service sees that and tries to connect using it? Just looking for a fairly high level understanding (with maybe some detail if you want to...)

    Read the article

  • Wake network adapter from deep sleep mode

    - by BeatMe
    I recently buyed a new Mainboard (Asrock ALiveXFire) and got some trouble with the network adapter. After switching my Windows 7 x64 in energey saving mode and returning from it, my network adapter couldn't be found. After some googling I found out, that apparently my network adapter has been put in a deep sleep mode and didn't reactivate. Their solution was to switch the PC off, take out the RAM and the CMOS battery for some time. After that, the adapter should be powered on again, but that didn't happen for me. I waited several hours before turning my PC on again, but that didn't help. Formatting and reinstalling didn't help either. The network adapter is not found in the hardware manager and reinstalling the drivers didn't help. I have the newest BIOS installed on the mainboard. I literally don't know what to try next. I'm thinking of returning my board, but I would like to avoid the hassle.

    Read the article

  • Unable to connect to OpenVPN server

    - by Incognito
    I'm trying to get a working setup of OpenVPN on my VM and authenticate into it from a client. I'm not sure but it looks to me like it's socket related, as it's not set to LISTEN, and localhost seems wrong. I've never set up VPN before. # netstat -tulpn | grep vpn Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:1194 0.0.0.0:* 24059/openvpn I don't think this is set up correctly. Here's some detail into what I've done. I have a VPS from MediaTemple: These are my interfaces before starting openvpn: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:39482 errors:0 dropped:0 overruns:0 frame:0 TX packets:39482 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3237452 (3.2 MB) TX bytes:3237452 (3.2 MB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:4885284 errors:0 dropped:0 overruns:0 frame:0 TX packets:4679884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:835278537 (835.2 MB) TX bytes:1989289617 (1.9 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:205.[redacted] P-t-P:205.186.148.82 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 I've followed this guide on setting up a basic server and getting a .p12 file, however, I was receiving an error that stated /dev/net/tun was missing, so I created it mkdir -p /dev/net mknod /dev/net/tun c 10 200 chmod 600 /dev/net/tun This resolved the error preventing the service from launching, however, I am unable to connect. On the server I've set up the myserver.conf file (as per the tutorial) to indicate local 127.0.0.1 (I've also attempted with the public IP address, perhaps I don't understand what they mean by local IP?). The server launches without error, this is what the log looks like when it starts: Sun Apr 1 17:21:27 2012 OpenVPN 2.1.3 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Mar 11 2011 Sun Apr 1 17:21:27 2012 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Sun Apr 1 17:21:27 2012 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Sun Apr 1 17:21:27 2012 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Sun Apr 1 17:21:27 2012 TUN/TAP device tun0 opened Sun Apr 1 17:21:27 2012 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500 Sun Apr 1 17:21:27 2012 GID set to openvpn Sun Apr 1 17:21:27 2012 UID set to openvpn Sun Apr 1 17:21:27 2012 UDPv4 link local (bound): [AF_INET]127.0.0.1:1194 Sun Apr 1 17:21:27 2012 UDPv4 link remote: [undef] Sun Apr 1 17:21:27 2012 Initialization Sequence Completed This creates a tun0 interface that looks like this: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the netstat command still indicates the state is not set to LISTEN. On the client-side I've installed the p12 certs onto two devices (one is an android tablet, the other is an Ubuntu desktop). I don't see port 1194 as open either. Both clients install the cert files and then ask me for the L2TP secret (which was set on the file), but then they oddly ask me for a username and a password, which I don't know where I could possibly get those from. I attempted all of my logins, and some whacky guesses that were frantically pulling at straws. If there's any more information I could provide let me know.

    Read the article

  • Should I use SSD Caching on non bootable HD?

    - by Onema
    I have an asus 9p79x pro which allows me to do SSD Caching. I have a 256 GB SSD drive that I use an my primary boot drive, and I have a 1 TB disk where I put most of my games, music, videos, dowloads, pictures, etc. I also have an extra 64 GB SSD Drive that I'm currently not using. I thought it would be a good idea to use it as my 1 TB disk cache and improve the load time of games and programs that are installed on the 1 TB disk; but will this work correctly? It seems from all that I have read online about this board that it is used to cache a boot drive. Any thoughts? Thank you

    Read the article

  • CentOS 6.2 Bridge Setup for KVM

    - by Gaia
    I'm trying to set up bridged networking with KVM on CentOS 6.2 to no avail. There are plenty of docs and tutorials about it, but they all seem to conflict or don't provide info specific enough to my situation. I just don't get it. I access the host via public IP "xxx.xxx.128.58". All other available IPs (/29) should be bridged and made available to the only KVM guest (running a public facing LAMP stack) that will be setup on this machine. The amazingly unhelpful NOC people assigned the extra IPs to eth1. Is this correct? Should br0 bridge to eth0 or eth1? How do I set this up? Here is the relevant info: eth0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BC inet6 addr: fe80::225:90ff:fe68:febc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:763 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:550811 (537.9 KiB) TX bytes:648 (648.0 b) Memory:fb980000-fba00000 eth1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.58 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 inet6 addr: fe80::225:90ff:fe68:febd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1806 errors:0 dropped:0 overruns:0 frame:0 TX packets:1505 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:133166 (130.0 KiB) TX bytes:106070 (103.5 KiB) Memory:fb900000-fb980000 eth1:0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.59 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.60 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:2 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.61 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:3 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.62 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) virbr0 Link encap:Ethernet HWaddr 52:54:00:62:55:68 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=XXXX.domain.com > brctl show bridge name bridge id STP enabled interfaces br0 8000.00259068febc no eth0 virbr0 8000.525400625568 yes virbr0-nic > ls -fl | grep ifcfg -rw-r--r-- 1 root root 198 Jun 7 10:58 ifcfg-eth0 -rw-r--r--. 1 root root 254 Oct 7 2011 ifcfg-lo -rw-r--r-- 1 root root 77 Jun 6 18:51 ifcfg-eth1-range0 -rw-r--r-- 1 root root 168 Jun 6 18:50 ifcfg-eth1 > cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO="static" BRIDGE="br0" HWADDR="00:25:90:68:FE:BC" IPV6INIT="yes" MTU="1500" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" IPADDR="yyy.yyy.216.131" NETMASK="255.255.255.128" > cat ifcfg-eth1 DEVICE="eth1" HWADDR="00:25:90:68:FE:BD" NM_CONTROLLED="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="xxx.xxx.128.58" NETMASK="255.255.255.248" GATEWAY="xxx.xxx.128.57" > cat ifcfg-eth1-range0 IPADDR_START="xxx.xxx.128.59" IPADDR_END="xxx.xxx.128.62" CLONENUM_START="0" Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xxx.xxx.128.56 * 255.255.255.248 U 0 0 0 eth1 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0 link-local * 255.255.0.0 U 1003 0 0 eth1 default xxx.xxx.128.57 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • dd-wrt and squid proxy

    - by Soe Naung Win
    I am now using linksys router with dd-wrt firmware & squid proxy from off-site (VPN) for anonymity. The problem is i have to configure proxy setting in my browser to access that proxy. What i would like to do is to get all my traffic pass through the router via squid proxy without configuring any setting in browser. I can't use openvpn due to port blockage in my country. My current squid proxy listen to port 443.

    Read the article

  • Are Motherboards for the Acer Aspire One AOA150 Netbook Compatible with the AOA110?

    - by Mindstormscreator
    I have an Acer Aspire One ZG5 AOA110-1588 netbook, and the motherboard doesn't have a port for a SATA 2.5 inch hard drive; it only supports this slow 8GB SSD type drive. Through research I've discovered that the AOA150 motherboards do have a SATA slot, and the bottom plate of these laptops have an appropriate protrusion for the drive to fit in (for example, compare this to this). The AOA110 and AOA150 models are very similar in appearance and specs. I've even seen tutorials that involve soldering a SATA connector onto the AOA110's motherboard, essentially creating an AOA150 motherboard (right?) So, could I just swap out the motherboard in my netbook with the MBS0506001? (I'd post another link to the actual board but can't because of the spam prevention...) I assume I would also need to purchase and replace the bottom cover with a larger one and possibly get a hard drive caddy as well...? Thanks!

    Read the article

  • dd-wrt and squid proxy

    - by Soe Naung Win
    I am now using linksys router with dd-wrt firmware & squid proxy from off-site (VPN) for anonymity. The problem is i have to configure proxy setting in my browser to access that proxy. What i would like to do is to get all my traffic pass through the router via squid proxy without configuring any setting in browser. I can't use openvpn due to port blockage in my country. My current squid proxy listen to port 443.

    Read the article

  • Accessing a persistent ssh tunnel

    - by woowaa
    How do I pass commands (shell) to a persistent SSH tunnel rather than open a connection for every instance? I have a Python scraper running on a client server which passes URL variables and shell commands to a remote host via a reverse tunnel (forwarded port), so that the URL's are then executed on the host (python fabric ssh localhost:12345 'browser open URL'). I could make the reverse tunnel persistent but how do I echo the url/command to the session? Update - ControlMaster (built into SSH) solves this one.

    Read the article

  • Connecting two Windows XP with MSMQ

    - by NealWalters
    I have MSMQ installed on two Windows XP computers. Can I configure them to pass messages back and forth, or do I need an MSMQ server in the middle? If I need an MSMQ server, does the normal MSMQ with Win2003 able to act as that? And then, how do I connect my Windows XP to that Windows 2003 server? Is it a) On screen admin dialog in the MSMQ plug-in to MMC, b) a config file, c) Active Directory, d) something else? Thanks, Neal Walters

    Read the article

  • Dedicated GPU in Dell PowerEdge C1100

    - by Eli Gundry
    We recently purchased a Dell PowerEdge C1100 off lease with the initention of using it for graphics processing. We installed an AMD HD 7000 series GPU in it that runs off of board power and it sends video to the display. That said, the video is very choppy, leading us to belive that the onboard video is doing all the processing and sending it to the card. Is there any way to either disable the VGA on this server or tell the OS to only use the dedicated card. More info: The server is running REHL 6.4 The graphics running the proprietary AMD drivers The video card only works in OS and does not show the BIOS on boot (we know that it's impossible to change this) Any ideas, guys? Update We are now thinking that the GPU is doing the graphics processing, but not working at the full speed of the PCI bus. Which is odd, because it is an x16 slot, but probably optimized to use a RAID card (if that makes any sense). Is there any way to remedy the choppy graphics on this server?

    Read the article

  • upgrading Subversion on Suse 10.0

    - by jessica
    I have a Suse Linux 10.0 with an old version of Subversion (1.4). I would like to upgrade it to the current (1.6.6) but I am having problem trying to understand how to build SVN from source. I mean, what should I pass to the configure script? Is there a simple way to upgrade the current SVN? thanks for the help. jessica

    Read the article

  • Roundcube can't connect to PostgreSQL database

    - by kenny.r
    I'm trying to install Roundcube on a CentOS 5.5 server, with a PostgreSQL 8.1.22 database. The first page of the installer script, that checks for the presence of php libraries and such, gives me green OKs across the board. I even went out of my way to install the optional ones. Page two generates me two configuration files (main.inc.php and db.inc.php) which I put into place. Page three is where things go wrong: Check DB config DSN (write): NOT OK(MDB2 Error: connect failed) Make sure that the configured database exists and that the user has write privileges DSN: pgsql://roundcube:password@localhost/roundcubemail The info you see there (user roundcube, password password, server localhost and database roundcubemail) is all correct. The database roundcubemail belongs to the user roundcube and it has write permissions. I have no clue why it can't connect to that database. I'm managing it with phpPgAdmin, which is running on the very same Apache, on the same server!

    Read the article

  • TimeZone Issue during DayLight Saving

    - by Viren
    I just been bugged by the Day light saving hours I seem that 3rd November 2013 01:00:00 start EST time Now ever Time I set my time to 3rd November 2013 00:58:xx(some seconds) and run date it give me valid Time zone i.e EDT but even after the time pass 01:00:00 and I still query the date library I still see the Time zone as EDT and not EST have a look at this screenshot You can clearly see the Time zone saying as EDT even when it is EST any one has a clue for this Update There is one other finding I found if I restart my machine I see this More Update Before Restart After Restart

    Read the article

  • TimeZone Issue during DayLight Saving

    - by user1328293
    I just been bugged by the Day light saving hours I seem that 3rd November 2013 01:00:00 start EST time Now ever Time I set my time to 3rd November 2013 00:58:xx(some seconds) and run date it give me valid Time zone i.e EDT but even after the time pass 01:00:00 and I still query the date library I still see the Time zone as EDT and not EST have a look at this screenshot You can clearly see the Time zone saying as EDT even when it is EST any one has a clue for this Update There is one other finding I found if I restart my machine I see this

    Read the article

< Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >